Search Results

Search found 17550 results on 702 pages for 'real world'.

Page 332/702 | < Previous Page | 328 329 330 331 332 333 334 335 336 337 338 339  | Next Page >

• What does the "Maximum Frequency" number mean in the Windows Resource Monitor?

  - by nhinkle

  In the Windows Resource Monitor's CPU tab, there is a status box and graph for the "Maximum Frequency", right next to the "CPU Usage" values. What does this mean? The value is sometimes over 100% on my system... what could that imply? By looking at CPU-z's real-time report of the processor's clock speed, it seems to be loosely related to what frequency the CPU is running at, which would imply that it means "percent of maximum possible frequency the CPU is running at"; this would be of relevance on systems with SpeedStep and/or TurboBoost technology (or similar). Furthermore, setting the system to "power saving mode" lowers the "maximum frequency" value to around 60%, while setting it to "high performance" mode sets it to around 110%. However, the percentage does not seem to exactly correlate to the CPU speed being shown. What value is this actually representing then?

  Read the article

• Considerations for a business looking to transition from PSTN to IP Telephony

  - by Bryce Thomas

  Full disclosure - This is related to a homework assignment question. I am not asking you to do my work for me, I am merely looking for some pointers and considerations to direct me in my further research. I have an assignment I'm working on where I've been given a scenario where a business wants to look into transitioning to using "Internet Telephone" as opposed to a traditional PSTN/PBX system and I need to write a report on it. I'm after some high level pointers from people, especially anyone that has been involved in a real life transition of this nature, on what some of the most important considerations are. These can be financial considerations, initial setup considerations, ongoing administrative considerations, quality of service considerations or anything else that is pertinent to performing such a transition.

  Read the article

• Nagios configuration management

  - by HannesFostie

  I am going to implement Nagios (most likely anyway, could turn out to be another tool as well) and I was wondering if anyone would like to share their best practices when it comes to creating, managing and maintaining the config files when it comes to scalability and managability as I find that it might quickly become a real big mess. Any tips, examples or even full configurations would be most welcome and I'd happily look them over. Tools would be welcome as well. Tried out NConf so far, but the generated config files don't seem to do what was promised (not including the parent information for one, and just a PITA to get them working - they generate a ton of errors when checking the config files with the script supplied by nagios) Thanks

  Read the article

• Unable to delete a directory from NTFS drive: "Access is denied"

  - by Evgeny

  I'm running Windows XP Pro x64 SP2. I have a directory on an NTFS drive that was created by a Maven build. A subsequent build attempted to delete this directory and failed. I now get the error "Access is denied" whenever I try to do anything with that directory: change to it, delete it, rename it. This happens both in Windows Explorer and from a command prompt. The properties dialog in Windows Explorer doesn't even contain the Security tab. I created the directory, so I don't think this is truly a permissions issue. I've occasionally had this error happen in the past is well. I believe the error is misleading, but the question is: what is the real problem and how do I fix it?

  Read the article

• Recurring events repeatedly saves a draft every minute

  - by Henrik Rasmussen

  Using Outlook 2010, some of my recurring (planned, not drafts) events is saving a draft to my Drafts folder every single minute as long as it's active. An example taken from real life is that I have a calendar entry (Appointment) occuring every day from 24-09-2012 until 28-09-2012 from 08:00 to 16:00 (GMT+1) with a blue category, only one participant (me) with subject but without a place. So every minute from 24-09-2012 until 28-09-2012 from 08:00 to 16:00, but not from 16:00 to 08:00, a new draft is automatically saved in my Drafts folder. How do I get rid of that behaviour? Addition here: Removing the offending event just allows a new one to take its place. There doesn't seem to be much on the sites - Microsoft calls it a "personal" issue, but there are more and more instances.

  Read the article

• Which kerberos flavor?

  - by Michael Lowman

  So I'm setting up a small network with all the standard stuff (files, email, etc.) and I've decided to go with a Kerberos+LDAP solution. Any ideas or recommendations on Heimdal vs. MIT? I've used MIT before, and tangentially Heimdal, but I don't really know of any real reason for using one over the other. I just know that I'd prefer not to realize I'd rather be running MIT after getting the whole Heimdal up and running with a full user database. If any other info'd be useful, I'm happy to provide.

  Read the article

• Where can I find a tutorial for PCB?

  - by BCS

  I'm looking at using this PCB layout program and looking for a tutorial for it. After skimming through the manual, and a few attempts at guessing how to use it, I have to say that in combination they are a near ideal example of how Not to make a UI easy to use. The GUI seems to borrow it's key combinations from vi (despite not being a text editor) and the manual seems to say more about what things do than how to do things. The closest I can find is this section that starts with the todo note: [...] do a real-world tutorial example.

  Read the article

• MRTG + RRDTool Hourly Graph

  - by SuperMicro321

  I am using MRTG + RRDtool to monitor the bandwidth on each switchport of a Cisco Catalyst 2950 via snmp. Is MRTG capable of generating an hourly graph? With RRDtool I was able to set the interval to 1 minute in hopes of getting a more detailed graph, but the shortest timeframe the graph is 'Daily' graph (5 Minute Average) and the image is too small. What I am looking to get out of this: I am looking to be able to visually monitor all of the switch ports and tell when port begins to have unusually high traffic, in real time (1 minute interval of snmp poll, graphs generated, and page refreshed).

  Read the article

• Architecture behind live streaming [on hold]

  - by l19

  I'm a Comp Sci undergraduate student, and I'm currently trying to understand the architecture behind streaming. I hear several terms and I'm not quite sure how they are related (e.g. streaming, broadcasting, ingesting, etc.) Is there a blog post or book that explains: How it all works in a high-level view (the workflow) The architecture (i.e. I capture content using my camera and want to display it real-time to an audience. I imagine that the content will be transferred to a server, but how does that server transmit the information to several users simultaneously?) Thanks!

  Read the article

• Install PHP on RedHat

  - by John R

  I just ran yum install php in the command prompt. Everything went fine ('complete!') as per the dialogue. I then uploaded a file that does not use short tags and is named with the proper extension (i.e., the name is test.php). <?php print "hello world"; ?> When I navigate my browser to test.php it just prints each of the characters shown above; i.e., PHP is not interpreting it. What might be the problem? Also, if there is a configuration file that needs to be updated, please tell me what directory path I am likely to find that file. Edit: Apache2 & Redhat

  Read the article

• How can I create an external SSL wrapper/tunnel page for an insecure webpage behind a firewall?

  - by Ross Rogers

  I have an security cam with a built-in webpage inside my home network. That camera is using basic HTTP authentication instead of SSL. I want to be able to access the camera's webpage from outside my network, but I don't want to open an unencrypted video stream to the outside world. Right now, I'm doing some cumbersome ssh tunneling where I bounce off an ssh server like: ssh -N -L 9090:CAMERA_IP:80 [email protected] and then I connect to my web page like: http://localhost:9090 But this is a pain. Now, gentle reader, I beseech you to tell me how I can use linux (Ubuntu) to get a fully encrypted SSL connection to my internal web page without the hassle of creating an ssh tunnel each time. I believe I can use stunnel, but I'm not sure of the command.

  Read the article

• Are speakers wasting power when they are not in use?

  - by Dennis Cheung

  I guess all of you have a pair/set of speakers for your MP3s. I am just interesting to how do they do when they are not playing? How actually the power spent by the speaker? Does any the below cases matter? Idle / Silence input When you computer is off / not connected Raise the volume by hardware (turn/push the button on the speaker) Raise the volume by software (do it with your mouse) BTW, to save the world. I am here to suggest you to unplug it when you leave your PC.

  Read the article

• Routing traffic to another internal network

  - by Jason

  OK, so here is the scenario. I have 4 Locations connected with an MPLS. I have installed an ASA at the primary location which is 10.20.1.0. Traffic is fine internally and to the world, however... I can't route traffic over the MPLS to another network. It is being blocked by an implicit deny rule even though there is a rule to allow any to any less secure interface (it should be using the same interface in/out, right?). I have a static route for the network in and the ASA can ping it - Just not traffic on the internal network of the ASA. -Jason

  Read the article

• Original sender is not correctly identified when spam is forwarded

  - by Stephan Burlot

  I have a forwarding rule with Postfix that forwards all messages to my main email address. When a spam message is sent to one of my emails, it is forwarded but the sender is shown as being the forwarding domain, not the spammer's domain. Real example: mywebsite.com is hosted on Linode. [email protected] sends an email to [email protected] the mail is forwarded to [email protected] my email hosting (anotherwebsite.com) sees it's spam and sends a message to [email protected] and Linode reports a TOS violation. I have modified my postfix settings so I now use RBL, but if a message goes through, it may happen again. How can I prevent this to happen again? Is there some settings to change on Postfix so the original sender is correctly identified? Thanks Stephan EDIT: The steps I did to prevent this to happen again are: Add RBL checking to Postfix Add postgrey to Postfix And finally fix the MX record which was incorrect. I checked with a test email on Spamcop.net and the original sender is correctly identified.

  Read the article

• Go frame-by-frame through a movie with a precise timer

  - by Matchu

  Hello, world: I have a video I made for physics class, which I intend to use to measure just how long an event took to take place. I can find the start frame and end frame easily using VLC's frame-by-frame feature. However, VLC's timer seems only to be precise to a single second, giving me no more precise an answer than "5 seconds." Is there a way in VLC, or any other program, to identify at precisely what time a particular frame in a video takes place? I have easy access to Ubuntu and Windows, and acquire a Mac if need be. If precise timer is not available, what number frame I am on will also work, since I know the framerate.

  Read the article

• write-through RAM disk, or massive caching of file system?

  - by Will

  I have a program that is very heavily hitting the file system, reading and writing randomly to a set of working files. The files total several gigabytes in size, but I can spare the RAM to keep them all mostly in memory. The machines this program runs on are typically Ubuntu Linux boxes. Is there a way to configure the file system to have a very very large cache, and even to cache writes so they hit the disk later? I understand the issues with power loss or such, and am prepared to accept that. Crashing aside, in normal operation the writes should eventually reach the disk! Or is there a way to create a RAM disk that writes-through to real disk?

  Read the article

• Port forwarding for VNC on Dynalink RTA1335 not working

  - by Curyous

  I've vnc-java running on an Ubuntu box, with the IP address 192.168.1.68, using port 5800 (because port 5900 is being used for normal VNC). If I connect to 192.168.1.68:5800 using another computer on the network, I can use VNC fine. Using www.whatismyip.com, I find out what my IP address from the outside world is, and if I go directly to that, I get to access my modem/router. If I try to navigate to that IP address, with ':5800' on the end, I get a "This web page is not available." error. I have port forwarding set up in the router as follows: Application Name External Packet Internal Host IP Address Protocol Port IP Address Port VNC ALL TCP/UDP 5800 192.168.1.68 5800 What else do I need to do to get this to work?

  Read the article

• what is the differences between (libapache2-mod-php5 ) and ( libapache2-mod-php5filter)

  - by tawfekov

  i had noticed that some code doesn't play nice when i use libapache2-mod-filter while it working as expected in libapache2-mod-php5 the error was generated by doctrine + it's very simple like : $db = new self(); $db["name"] = $name; $db["desc"] = $desc; $db->save(); /// it throw the error here error message like : Syntax error or access violation: 1064 You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near 'desc) VALUES ('aaaaaaaaaaa', 'aaaaaaaaaaaa')' at line 1 so what is the real difference between the both modules for php5 ???

  Read the article

• How would I / could I obtain an reasonably comprehensive list of domain names?

  - by Simon

  I know that domain names are constantly changing, and I know there are a lot of them, but there is clearly a region of the domain name space which is stable. How would I go about getting a list, even a very big one? Such a thing must logically exist, even if it is in a distributed form, because the web's DNS servers resolve names to IP addresses. So in theory if I could poll all the DNS servers in the world at a moment in time I would have the complete list of mapped names. Is there a practical way of doing that? As an aside, does anyone have any good estimates of how many domain names exist at the moment?

  Read the article

• Linux Software RAID: How to fsck on hard drive?

  - by Rick-Rainer Ludwig

  We have a Linux server running with Software RAID1. We see some issues in /var/log/messages like: unreadable sector. I want to perform a complete fsck on the drive to get some more information, but a fsck /dev/md0 brings a clean due to the Software RAID layer in between. How can I check the real hard drive? Do I need to disassemble the whole RAID? How do I deal with the inconsistency in the partition due to the additional Software RAID header? Does anyone have a good idea for this?

  Read the article

• How to switch users without entering password

  - by torbengb

  I'm a newbie running Ubuntu 9.10. I have two users (wife and me), and each user's screensaver is set to lock so that on wakeup, we get to choose which user's desktop to go to. However, Ubuntu requires a password, so this is pretty tedious. I'd like to switch users without entering any password. I know about this trick that works for the boot login, but it doesn't deal with multiple users. Is it possible to set empty passwords for users in Ubuntu, or skip the password in other ways? (I'm expecting real Linux users to suggest that passwordless users must not get any rights and there be an admin user with a strong password. Yes, you're right. But that's not what this question is about. Thanks.)

  Read the article

• 5v PCI to PCI-X or PCIe adapter?

  - by SiegeX

  We unfortunately have a very expensive ($10K) full-length 5 volt PCI card that we would like to use in the same system as another expensive PCI-X card. As luck would have it, it seems that PCI-X is not backwards compatible with 5v PCI cards. It would be a real shame to have to order a whole new server just to accommodate these two cards together. Does there exist any internal converter/adapter that will allow one to place a full-length 5v PCI card into either a PCI-X or PCIe slot? I've found an external expansion box that suits our needs but it's 1) External and 2) $1100. The only internal adapters I've been able to find go from Low-profile PCI - PCIe; nothing that seems to support full-height, full-length PCI cards.

  Read the article

• Recommended website performance monitoring services? [closed]

  - by Dennis G.

  I'm looking for a good performance monitoring service for websites. I know about some of the available general monitoring services that check for uptime and notify you about unavailable services. But I'm specifically looking for a service with an emphasis on performance. I.e., I would like to see reports with detailed performance statistics from multiple locations world-wide, with a break-down on how long it took to fetch the different website resources, including third-party scripts such as Google Analytics and so on (the report should contain similar details such as the FireBug Net tab). Are there any such services and if so, which one is the best?

  Read the article

• Max ping response time?

  - by DougN

  I'm wondering what a maximum (practical) ping response time might be. As far as I know, there isn't a max defined anywhere (TTL, but that's hops, not time). As I think about it, I'm not sure I've ever seen a ping response time of more than a second or so. But as far as I know, there is nothing to stop a remote host from waiting (or being really busy) and not sending the response back for a few seconds. As a simple data point, I just pinged a number of servers around the world and the worst time I could find was 350ms.

  Read the article

• installing plugins in vim

  - by Ying

  I had a real difficulty installing vim plugins on mac. I know for a plugin to be installed it has to be seen by runtimepath. According to vim docs, this is Macintosh: "$VIM:vimfiles, $VIMRUNTIME, $VIM:vimfiles:after" First off, what does $VIM:vimfiles mean?? It is certainly not $VIM/vimfiles, as (~/.vim/vimfiles) does not work. So my options are 1) put my plugin in /usr/share/vim/vim73 (my $VIMRUNTIME, which i know to be BAD) 2) find a way to make vim look at my home directory when including plugins. I have putting my plugin in: ~/.vim/plugin.vim ~/.vim/vimfiles/plugin.vim ~/.vim/plugin/plugin.vim All to no avail. Can somebody help me out here? Thanks!

  Read the article

< Previous Page | 328 329 330 331 332 333 334 335 336 337 338 339  | Next Page >