Search Results

Search found 36698 results on 1468 pages for 'old linux fan'.

Page 335/1468 | < Previous Page | 331 332 333 334 335 336 337 338 339 340 341 342  | Next Page >

• Reset KDE System Monitor (KSysGuard)

  - by Deltik

  Something went wrong while I was attempting to restore a backup, and KDE System Guard ceased to display properly. This is the correct display (command running from root: kdesudo ksysguard): This is the incorrect display (command: ksysguard): Here in the incorrect display, the menu bar is missing, and the tab "Process Table" is unclickable. I have already tried to remove the directory ~/.kde/share/apps/ksysguard/ but to no avail. My question: How do I restore KSysGuard back to factory defaults/normal functionality?

  Read the article

• ssh_exchange_identification: Connection closed by remote host

  - by Charlie Epps

  First: $ ssh-keygen -t dsa -P '' -f ~/.ssh/id_dsa $ cat ~/.ssh/id_dsa.pub >> ~/.ssh/authorized_keys Connecting to SSH servers gives this message: $ ssh -vvv localhost OpenSSH_5.3p1, OpenSSL 0.9.8m 25 Feb 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to localhost [127.0.0.1] port 22. debug1: Connection established. debug1: identity file /home/charlie/.ssh/identity type -1 debug1: identity file /home/charlie/.ssh/id_rsa type -1 debug3: Not a RSA1 key file /home/charlie/.ssh/id_dsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/charlie/.ssh/id_dsa type 2 ssh_exchange_identification: Connection closed by remote host My /etc/hosts.allow is as following: sshd: ALLOW /etc/hosts.deny is as following: ALL: ALL: DENY I have changed my /etc/ssh/sshd_conf as following: ListenAddress 0.0.0.0 Protocol 2 # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys PasswordAuthentication no

  Read the article

• When I restart my virtual enviorment it does not re-bind to the IP address

  - by RoboTamer

  The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

  Read the article

• Debian and Multipath IO problem

  - by tearman

  Basically the situation is, I have a box running Debian, the box internally has an Intel SCSI RAID controller which is controlling 2 hard drives in RAID1 mode which is where the OS is installed. Further, I have a QLogic fiber channel adapter that connects the unit to a Fiber Channel SAN. My process of installation is I'll install Debian to the local drives, and leave the QLogic firmware out of it for the time being. Then once I get the unit online, I'll install the firmware drivers. This flops my internal drives from /dev/sda to /dev/sdc, which is a bit annoying, but recoverable. Probably should address these by UUID anyways. Once I get back online, I have to install multipath-tools (the framework is a multipath framework). However, once I reboot the machine again, it fails on boot after discovering multipath targets, saying my local drives are busy and cannot be mounted to /root. Any help in what may be the problem here? Or at least how to disable multipath until after the unit boots and then ignores the internal drives?

  Read the article

• How do I make some files on my machine accessible via HTTP using Apache?

  - by Lazer

  I did a wget on the source and built the apache binaries correctly. Now what do I need to do to get some documents accessible using HTTP (start some services?)? Also, do I need to group all the files I want to make accessible in some directory and make the directory and its contents accessible or can I just make the individual documents available? I will be providing these links to my colleagues and do not want them to be down, so need to make sure that the apache services are up automatically after a reboot. Does apache have some inbuilt support for this?

  Read the article

• Error in applying patch in Apache

  - by newbie.my

  Recently i have installing apache 2.2.21 from the source for testing purpose. After doing clean installation of apache i want to patch it with the patches provided here: http://www.apache.org/dist/httpd/patches/ Anyway when i put the patch command as mention in the page it show this result: File to patch: CVE-2011-3368.patch 1 out of 1 hunk FAILED -- saving rejects to file CVE-2011-3368.patch.rej Is there something wrong with my patch?If not,how could i verified that the patch has been implemented or not?

  Read the article

• Installed ASUS HD4670, now unable to install ANY Debian due to low memory corruption

  - by Alfabravo

  I have a desktop PC which initially had the Intel D946gzis mobo, its chipset as video controller, some RAM and so. There I installed Debian without a problem alongside WindowsXP. I've bought an ASUS HD 4670 video card, installed it on the PC and now the installed Debian does not work, while the Ubuntu live CD refuses to run no matter if I set acpi, apic on or off... it throws me some low memory corruption at position just like shown here. With normal configuration, Debian throws kernel panic (keyboard lights blinking). Anyone have faced this before? Ideas? Thanks!! (meanwhile, debian hides in a virtualbox :'( ) Edited: Tried Ubuntu 9.10 x64 (due to the fact i've a core2duo at 2GHz) and it throws a kernel-panic to me (flashing caps and num LEDs). On screen, can be read different lines with things like: ... [ 1.957161] [] rb_erase+0xd6/0x160 [ 1.957266] [] page_fault+0x25/0x30 Could it be something about this new video card having ddr3?

  Read the article

• Hylafax: Encounter "No font metric information" when try to send a fax

  - by Chau Chee Yang

  I am using Hylafax 6.0.5 on Fedora 13 x86_64. As there are no rpm package available for Fedora 13, I use the source tar ball to install hylafax myself. Everything seems fine during compile and install. I try to send a fax with sendfax and encounter error: # sendfax -n -d <fax-number> /etc/passwd /usr/local/sbin/textfmt: No font metric information found for "Courier-Bold". Usage: /usr/local/sbin/textfmt [-1] [-2] [-B] [-c] [-D] [-f fontname] [-F fontdir(s)] [-m N] [-o #] [-p #] [-r] [-U] [-Ml=#,r=#,t=#,b=#] [-V #] files... >out.ps Default options: -f Courier -1 -p 11bp -o 0 Error converting document; command was "/usr/local/sbin/textfmt -B -f Courier-Bold -Ml=0.4in -p 11 -s default >'/tmp//sndfaxp5GdJ9' <'/etc/passwd'" It seems like there is problem with font problem. I have ghostscript-fonts installed too. I can't find hyla.conf in path /etc/hylafax. There is no /etc/hylafax path in my file system. All configuration files seems located in /var/spool/hylafax/etc. Please advice. Thank you.

  Read the article

• GlassFish will not start when SNMP is enabled

  - by edarc

  I have a GlassFish v3 app server running on 64-bit Debian Lenny. Everything is running fine, except I would like to monitor GF's JVM instance with SNMP. However, every time I try to enable it by adding the following <jvm-options> in domain.xml: -Dcom.sun.management.snmp.port=10161 -Dcom.sun.management.snmp.acl.file=/path/to/snmp.acl -Dcom.sun.management.snmp.interface=127.0.0.1 GlassFish refuses to start: $ asadmin start-domain Waiting for DAS to start .Error starting domain: default. The server exited prematurely with exit code 1. Command start-domain failed. $ There is also nothing illuminating (well, really nothing at all) in jvm.log or server.log. The snmp.acl file contains: acl = { { communities = public access = read-only managers = localhost } } and is chmod 600 (I know this is not the problem because it will actually fail with an error about the permissions if it is set to anything other than 600) $ java -version java version "1.6.0_0" OpenJDK Runtime Environment (build 1.6.0_0-b11) OpenJDK 64-Bit Server VM (build 1.6.0_0-b11, mixed mode)

  Read the article

• Advantages of Ubuntu LTS versions over regular Ubuntu?

  - by Adam Matan

  Do the LTS versions of Ubuntu have any advantages for the non-paying customers (who don't get any support?) From the tech spec only, these versions seem outdated in many aspects - mainly drivers and installed software versions. For instance, My previous (bounty!) problem regarding the AGN 5100 drivers would have been solved under Ubuntu 9.04.

  Read the article

• how to install glive

  - by neha soni

  how to install glive in ubuntu

  Read the article

• DRBD Not syncing between my nodes

  - by Mike Curry

  Some version info: Operating system is Ubuntu 11.10, on EC2, kernel is 3.0.0-16-virtual and the application info is: Version: 8.3.11 (api:88) GIT-hash: 0de839cee13a4160eed6037c4bddd066645e23c5 build by buildd@allspice, 2011-07-05 19:51:07 Getting some strange errors in dmesg (seen below) as well, there is no replication happening. I have made my first node primary and its showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Primary/Unknown UpToDate/DUnknown r----s ext3 my secondary node is showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Secondary/Unknown Inconsistent/DUnknown r----s Showing /proc/drbd on the master shows: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Primary/Unknown ds:UpToDate/DUnknown r----s ns:0 nr:0 dw:4 dr:1073 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Showing /proc/drbd on the slave shows that there is nothing being transfered... version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Secondary/Unknown ds:Inconsistent/DUnknown r----s ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Here is my config... resource r0 { protocol C; startup { wfc-timeout 15; degr-wfc-timeout 60; } net { cram-hmac-alg sha1; shared-secret "test123; } on drbd01 { device /dev/drbd0; disk /dev/xvdm; address 23.XX.XX.XX:7788; # blocked out ip meta-disk internal; } on drbd02 { device /dev/drbd0; disk /dev/xvdm; address 184.XX.XX.XX:7788; #blocked out ip meta-disk internal; } } I have run the following on the master: sudo drbdadm -- --overwrite-data-of-peer primary all There is no firewall between the systems. Here is the dmesg with some errors: [2285172.969955] drbd: initialized. Version: 8.3.11 (api:88/proto:86-96) [2285172.969960] drbd: srcversion: DA5A13F16DE6553FC7CE9B2 [2285172.969962] drbd: registered as block device major 147 [2285172.969965] drbd: minor_table @ 0xffff88000276ea00 [2285173.000952] block drbd0: Starting worker thread (from drbdsetup [1300]) [2285173.003971] block drbd0: disk( Diskless -> Attaching ) [2285173.006150] block drbd0: No usable activity log found. [2285173.006154] block drbd0: Method to ensure write ordering: flush [2285173.006158] block drbd0: max BIO size = 4096 [2285173.006165] block drbd0: drbd_bm_resize called with capacity == 524271928 [2285173.008512] block drbd0: resync bitmap: bits=65533991 words=1023969 pages=2000 [2285173.008518] block drbd0: size = 250 GB (262135964 KB) [2285173.079566] block drbd0: bitmap READ of 2000 pages took 17 jiffies [2285173.081189] block drbd0: recounting of set bits took additional 1 jiffies [2285173.081194] block drbd0: 250 GB (65533991 bits) marked out-of-sync by on disk bit-map. [2285173.081203] block drbd0: Suspended AL updates [2285173.081210] block drbd0: disk( Attaching -> UpToDate ) [2285173.081214] block drbd0: attached to UUIDs 1C1291D39584C1D1:0000000000000004:0000000000000000:0000000000000000 [2285173.095016] block drbd0: conn( StandAlone -> Unconnected ) [2285173.095046] block drbd0: Starting receiver thread (from drbd0_worker [1301]) [2285173.099297] block drbd0: receiver (re)started [2285173.099304] block drbd0: conn( Unconnected -> WFConnection ) [2285173.099330] block drbd0: bind before connect failed, err = -99 [2285173.099346] block drbd0: conn( WFConnection -> Disconnecting ) [2285173.295788] block drbd0: Discarding network configuration. [2285173.295815] block drbd0: Connection closed [2285173.295826] block drbd0: conn( Disconnecting -> StandAlone ) [2285173.295840] block drbd0: receiver terminated [2285173.295844] block drbd0: Terminating drbd0_receiver Edit: Reading some other similar issues, it was suggested to do a 'drbdadm dump all', so I figured it couldn't hurt. ubuntu@drbd01:~$ drbdadm dump all /etc/drbd.conf:19: in resource r0, on drbd01: IP 23.XX.XX.XX not found on this host. and on slave: root@drbd02:~# drbdadm dump all /etc/drbd.conf:25: in resource r0, on drbd02: IP 184.XX.XX.XX not found on this host. Strange it doesn't find its own ip, however, this is an Amazon EC2 system using an elastic IP... here are my ipconfigs for both... master: ubuntu@drbd01:~$ ifconfig eth0 Link encap:Ethernet HWaddr 22:00:0a:1c:27:11 inet addr:10.28.39.17 Bcast:10.28.39.63 Mask:255.255.255.192 inet6 addr: fe80::2000:aff:fe1c:2711/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1569 errors:0 dropped:0 overruns:0 frame:0 TX packets:1169 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:124409 (124.4 KB) TX bytes:213601 (213.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) slave: root@drbd02:~# ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3f:00:14:9d inet addr:10.160.27.107 Bcast:10.160.27.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3fff:fe00:149d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:774 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:75381 (75.3 KB) TX bytes:109673 (109.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

  Read the article

• how to resolve error in ubuntu

  - by Bipul

  i m using ubuntu 9.04. when i m running any command like sudo apt-get update ,i get following error message"E: Type 'l.com/ubuntu' is not known on line 45 in source list /etc/apt/sources.list E: The list of sources could not be read. ".due to this problem i m not able to download anything.please help

  Read the article

• What can cause an increase in inactive memory and how to reclaim it?

  - by Boaz

  I have heavy application running on a CentOS server and I'm seeing a strange memory behavior. Here is a snapshot of a munin graph: As you can see the amount of committed memory increases gradually causing the swap file to be use. What strikes me odd is that the amount of inactive memory keeps growing as well. It is my understanding that the inactive memory is actually memory freed up but not yet clean by the OS and put back in the free memory pool. It seems that running out of memory is acutally caused by this lack of clean up, but I may be wrong. Can you give some tips to find the cause of the problem and/or cause CentOS to reclaim the inactive memory? Thanks. Some extra info: 1) I have a tmpfs mounted on /tmp and the number of files stored there grows (but it is double the amount of the inactive memory). 2) cat /proc/meminfo (at a later stage than the image) gives: MemTotal: 14371428 kB MemFree: 1207108 kB Buffers: 35440 kB Cached: 4276628 kB SwapCached: 785316 kB Active: 9038924 kB Inactive: 3902876 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 14371428 kB LowFree: 1207108 kB SwapTotal: 10223608 kB SwapFree: 6438320 kB Dirty: 627792 kB Writeback: 0 kB AnonPages: 7844560 kB Mapped: 49304 kB Slab: 146676 kB PageTables: 27480 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 17409320 kB Committed_AS: 16471488 kB VmallocTotal: 34359738367 kB VmallocUsed: 275852 kB VmallocChunk: 34359462007 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 2048 kB 3) The application is a combination of MySQL, Heritrix (http://crawler.archive.org/ ) and a Tomcat based Java servlet to manage things.

  Read the article

• Cannot create file in directory even though it's writable by a group I belong to

  - by Alan Berndt

  I have a directory structure owned by a certain group, and I am a member of the group that owns these directories. I am able to create files in one directory, but not in another, even though the permissions are the same. alan@bricky:/mnt/storage/media$ stat Music Music\ \(Lossy\)/ File: `Music' Size: 34 Blocks: 8 IO Block: 4096 directory Device: fb00h/64256d Inode: 4215424 Links: 3 Access: (2775/drwxrwsr-x) Uid: ( 1001/ media) Gid: ( 1001/ media) Access: 2011-08-19 11:45:03.182586898 -0700 Modify: 2011-08-19 11:44:01.412840027 -0700 Change: 2011-08-19 11:45:02.734603240 -0700 File: `Music (Lossy)/' Size: 6 Blocks: 8 IO Block: 4096 directory Device: fb00h/64256d Inode: 1512056832 Links: 2 Access: (2775/drwxrwsr-x) Uid: ( 1001/ media) Gid: ( 1001/ media) Access: 2011-08-19 11:45:03.190586606 -0700 Modify: 2011-08-19 10:34:46.526530313 -0700 Change: 2011-08-19 11:45:02.738603094 -0700 alan@bricky:/mnt/storage/media$ touch Music/test alan@bricky:/mnt/storage/media$ touch Music\ \(Lossy\)/test touch: cannot touch `Music (Lossy)/test': Permission denied

  Read the article

• Using PAM and vsftpd without root access

  - by Zizzencs

  I'm trying to set up a few vsftpd instances on a machine that I have no root access to. The authentication should be done through PAM with pam_listfile, like this: pam_listfile.so item=group sense=allow file=/path/filename onerr=fail I can ask the administrator to set up a PAM service for me and include that line but he is not willing to create 6 PAM services for my 6 vsftpd instances and I really need different /path/filename set for each vsftpd server. Is there a way to solve this problem? Can I somehow not use absolute path as the parameter? (I know the correct solution would be to use one vsftpd instance and set up virtual users properly. However unfortunately I have to work what I have and the users already exist in an Active Directory and are authenticated to the system using another PAM service.)

  Read the article

• Install notify-osd on Opensuse 11.2

  - by Rafael

  Is it possible to use the notify-osd instead of libnotify in Opensuse 11.2 ? if it's possible then how ? should i just install notify-osd over libnotify ?? Thanks in advance.

  Read the article

• Proftp error message Fatal: unknown configuration directive 'DisplayFirstChdir' on line 22 of '/etc/proftpd/proftpd.conf'

  - by LedZeppelin

  Sorry for the newb factor but I'm trying to set up a server using this guide: http://www.intac.net/build-your-own-server/ I'm at the end of step 5 and when I try to restart proftp I get the following error message me@me-desktop:~$ sudo service proftpd restart * Stopping ftp server proftpd [ OK ] * Starting ftp server proftpd Fatal: unknown configuration directive 'DisplayFirstChdir' on line 22 of '/etc/proftpd/proftpd.conf' [fail] Any clues on how to change line 22?

  Read the article

• Sudoers file permissions

  - by twigg

  I'm trying to run the following command without the need for sudo: echo 1 | sudo tee -a /sys/block/$hd/device/delete The $hd variable changes dynamically from sdb - sdi for each one of my HDD's in my drive bay. I added the following line to the sudoers file: operator ALL=/sys/block/sdb/device/delete But this didn't make a difference its still asking for sudo password even if I run: echo 1 | sudo tee -a /sys/block/sdb/device/delete

  Read the article

• GDM Won't Automatically Start After Boot

  - by Mikey.B

  Ubuntu 10.04 Hi guys. I'm not sure why but quite recently, my ubuntu desktop started bringing up the command prompt login screen after booting. I want GDM to start up by default. I can manually bring up GDM by typing: sudo service gdm start or sudo /usr/sbin/gdm but I want something more permanent. The contents of /etc/X11/default-display-manager point to /usr/sbin/gdm The chkconfig status for GDM shows that it's off on all run levels... could that be it? I tried running: sudo chkconfig --add gdm and just got errors... Any ideas? How can I get GDM to automatically come up again? Any/all help is appreciated! -M

  Read the article

• Attempting to update Amazon Route53 using a script, but domain is not being updated

  - by ks78

  I have several Amazon EC2 instances, running Ubuntu 10.04, with which I'd like to use Amazon's Route53. I setup a script as described in Shlomo Swidler's article, but I'm still missing something. When the script runs, it doesn't return any output, which I initially assumed meant it ran correctly. However, when I check the DNS records using MyR53DNS, there are no entries for my instances. Here's my script: #!/bin/tcsh -f set root=`dirname $0` setenv EC2_HOME /usr/lib/ec2-api-tools setenv EC2_CERT /etc/cron.route53/ec2_x509_cert.pem setenv EC2_PRIVATE_KEY /etc/cron.route53/ec2_x509_private.pem setenv AWS_ACCESS_KEY_ID myaccesskeyid setenv AWS_SECRET_ACCESS_KEY mysecretaccesskey /user/bin/ec2-describe-instances | \ perl -ne '/^INSTANCE\s+(i-\S+).*?(\S+\.amazonaws\.com)/ \ and do { $dns = $2; print "$1 $dns\n" }; /^TAG.+\sShortName\s+(\S+)/ \ and print "$1 $dns\n"' | \ perl -ane 'print "$F[0] CNAME $F[1] --replace\n"' | \ xargs -n 4 $/etc/cron.route53/cli53/cli53.py \ rrcreate -x 60 mydomain.com Does anyone see a problem with this script? If its not the script, what else could be preventing my Route53 domain from being updated? I am using the Security Groups to IP-restrict the instances. I've tried opening port 53, but that didn't seem to have an effect. Is there another port that Route53 uses? I'd appreciate any help or guidance the ServerFault community can offer. Let me know if you need any further info.

  Read the article

• Setting a custom timeout to nmblookup

  - by C2H5OH

  As part of a batch script, I have the following command: hostname=$(nmblookup -A $ip_address | awk '$2 == "<20>" {print $1}') Which works fine from a functinality perspective, even for unresolved hosts. The problem is that when the IP address is not reachable or the remote machine does not respond to the SMB request, the command takes about ten seconds to complete. Therefore, the question is simple: is there a way to lower the elapsed time in such cases? Or, in other words, is there a way to set a custom timeout for the nmblookup command? NOTE: I'm interested in solutions that do not make use of SIGALRM or similar mechanisms; if they exist. The nmblookup version is 3.6.3 from Ubuntu 12.04 LTS.

  Read the article

• How can i remove some installed python modules in centos

  - by user1513613

  I am getting ths error Python 2.7.5 (default, Jul 2 2013, 13:33:13) [GCC 4.4.7 20120313 (Red Hat 4.4.7-3)] on linux2 Type "help", "copyright", "credits" or "license" for more information. >>> import MySQLdb Traceback (most recent call last): File "<stdin>", line 1, in <module> File "MySQLdb/__init__.py", line 23, in <module> (version_info, _mysql.version_info)) ImportError: this is MySQLdb version (1, 2, 4, 'final', 1), but _mysql is version (1, 2, 3, 'final', 0) >>> Now i dont know how i have installed that. i treid so many things like yum , pip easy, install etc. how can i remove all versions of MysqlDB FROM THERE

  Read the article

• Installing VLC on CentOS 6.2

  - by suraj

  I'm using CentOS 6.2, and I tried to install VLC Player using yum, but it shows "No package vlc available". I tried below command: [root@localhost ~]# yum install vlc Loaded plugins: fastestmirror, refresh-packagekit Loading mirror speeds from cached hostfile * base: ftp.iitm.ac.in * extras: ftp.iitm.ac.in * updates: ftp.iitm.ac.in base | 3.7 kB 00:00 extras | 3.5 kB 00:00 updates | 3.5 kB 00:00 updates/primary_db | 3.4 MB 01:17 virtualbox | 951 B 00:00 Setting up Install Process No package vlc available. Error: Nothing to do Is there any rpm package available?

  Read the article

• What can cause an increase in inactive memory and how to reclaim it?

  - by Boaz

  Hi All, I have heavy application running on a CentOS server and I'm seeing a strange memory behavior. Here is a snapshot of a munin graph: As you can see the amount of committed memory increases gradually causing the swap file to be use. What strikes me odd is that the amount of inactive memory keeps growing as well. It is my understanding that the inactive memory is actually memory freed up but not yet clean by the OS and put back in the free memory pool. It seems that running out of memory is acutally caused by this lack of clean up, but I may be wrong. Can you give some tips to find the cause of the problem and/or cause CentOS to reclaim the inactive memory? Thanks. Some extra info: 1) I have a tmpfs mounted on /tmp and the number of files stored there grows (but it is double the amount of the inactive memory). 2) cat /proc/meminfo (at a later stage than the image) gives: MemTotal: 14371428 kB MemFree: 1207108 kB Buffers: 35440 kB Cached: 4276628 kB SwapCached: 785316 kB Active: 9038924 kB Inactive: 3902876 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 14371428 kB LowFree: 1207108 kB SwapTotal: 10223608 kB SwapFree: 6438320 kB Dirty: 627792 kB Writeback: 0 kB AnonPages: 7844560 kB Mapped: 49304 kB Slab: 146676 kB PageTables: 27480 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 17409320 kB Committed_AS: 16471488 kB VmallocTotal: 34359738367 kB VmallocUsed: 275852 kB VmallocChunk: 34359462007 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 2048 kB 3) The application is a combination of MySQL, Heritrix (http://crawler.archive.org/ ) and a Tomcat based Java servlet to manage things.

  Read the article

< Previous Page | 331 332 333 334 335 336 337 338 339 340 341 342  | Next Page >