Search Results

Search found 12283 results on 492 pages for 'tcp port'.

Page 338/492 | < Previous Page | 334 335 336 337 338 339 340 341 342 343 344 345  | Next Page >

• Nginx + PHP FASTCGI FAILS - how to debug ?

  - by Niro

  I have a server on AMAZON EC2 running Nginx +PHP with PHP FASTCGI via port 9000. The server runs fine for a few minutes and after a while (several thousands of hits in this case) FastCGI Dies and Nginx returns 502 Error. Nginx log shows 2010/01/12 16:49:24 [error] 1093#0: *9965 connect() failed (111: Connection refused) while connecting to upstream, client: 79.180.27.241, server: localhost, request: "GET /data.php?data=7781 HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "site1.mysite.com", referrer: "http://www.othersite.com/subc.asp?t=10" How can I debug what is causing FastCGI to die?

  Read the article

• How do I configure Shrewsoft's VPN client to only route traffic to a certain IP address through the VPN?

  - by dommer

  We're using Shrewsoft's VPN client to connect to a third party development server. However, it seems to be configured to send all or nothing through the VPN. The devs have to disconnect from the VPN to get email/internet access back. The server that needs to be accessed via the VPN is on a specific (local - 10.x.x.x) IP address and a specific ports. Can we configure the Shrewsoft client application to only route traffic to that one address and/or port through the VPN and to route anything else though the usual channels? If so, how is it done? I'm not a VPN specialist and the options are confusing. In the absence of any Shewsoft VPN client specific advice, what should I be search for? Split tunnels?

  Read the article

• Assisting a user using VNC

  - by wizlog

  I'm trying to help a friend with their computer remotely. He has a version of VNC, I'm not sure which one, so I downloaded and installed the VNC Viewer and Listening Viewer. I ask my friend for his IP address and port number, and he tells me that every time he's used it, the person giving him assistance (remotely controlling his computer) gave him some kind of number. I should note that my friend is not tech savy, and it may have been an IP address, but I'm not sure. What kind of number would the user be looking for? Does this indicate his version of VNC, Does that even matter? I am completly forign to VNC and don't know where to begin looking for an answer myself, and (for whatever reason) I can't ask my friend to figure out what version of VNC he is using.

  Read the article

• How to write a ProxyPass rule to go from HTTPS to HTTP in IIRF

  - by Keith Nicholas

  I have a server which is running a web app that self serves HTTP. I'm wanting to use IIS6 (on the same server) to provide a HTTPS layer to this web app. From what I can tell doing a reverse proxy will allow me to do this. IIRF seems like the tool to do this job. There are no domain names involved.... its all ip numbers. So I think I want :- https:<ipnumber>:5001 to send all its requests to the same server but on a different port and use HTTP ( not exposed to the net ) http:<ipnumber>:5000 but not sure how to go about it with IIRF, I'm not entirely sure how to write the rules? I think I need to make a virtual web app on 5001 using HTTPS? then add a rules file.

  Read the article

• How to use mod_proxy to let my index of Apache go to Tomcat ROOT and be able to browse my other Apac

  - by Dagvadorj

  Hello, I am trying to use my Tomcat application (deployed at ROOT) to be viewed from Apache port 80. To do this, I used mod_proxy, since mod_jk made me try harder. I used sth like this in httpd.conf: <location http://www.example.com> Order deny,allow Allow from all PassProxy http://localhost:8080/ PassProxyReverse http://localhost:8080/ </location> <Proxy *> Order deny,allow Allow from all </Proxy> And now I can not retrieve my previous sites on Apache, which was running prior to my configuration. How can I have both running?

  Read the article

• Windows 7 Line In Delay Issue

  - by CheeseConQueso

  Not sure if this question should be posted on a different stack exchange site, so if you find that it should not be posted here, please move it. Either way, if you know the solution, please advise. I'm running Windows 7 Pro 32-bit on my Dell Latitude 2100 netbook and I'm having an issue with the line in device/driver/functionality. The device & driver are stock: Driver Date: 7/13/2009 Driver Version: 6.1.7600.16385 I'm almost sure that the manufacturer of the sound card is RealTek. The problem is that there is a delay (when monitoring input) between the source and the speakers. My setup is bass guitar running through a 12' long instrument cable (1/4") with a 1/4" female to 1/8" male adapter into the line in port on the computer. Then the 15' long headphones/line out cable goes into a standard set of powered speakers. How do I get rid of this delay? Thanks for any help.

  Read the article

• ASA firewalls: how does stateful filtering affect my access lists?

  - by Nate

  Ok, so assume that I have an ingress access list that looks like this: access-list outside_in extended ip permit any X.Y.Z.1 eq 25 access-group outside_in in interface outside And I want to do egress filtering. I want to allow inside machines to respond on port 80, and I want to allow ports over 1024. Given that the firewall is statefull, do I need to have the rule access-list inside_in extended ip permit X.Y.Z.1 any eq 25 in my inside_in ACL, or can I get away with just access-list inside_in extended ip permit any any gt 1024 access-group inside_in in interface inside In other words, if I apply an egress access list, do I have to explicitly allow machines to respond to requests allowed by the ingress access list, or does the statefullness of the firewall handle that for me? Thanks!

  Read the article

• postfix, webmin installed. whats next?

  - by Johnny Craig

  Im trying to get imap running and dont know the problem. i a developer, not a network guy.( our network guy left) we had postfix installed already for outgoing mail on 8 domains. we only had incoming on 1 domain. but that mail server is located on a different ip. now we want incoming on another domain, but we dont want it on another ip, we want it on the same ip as the website itself. I installed dovecot today because my hosting company said i needed it. it seems to run fine. do i need dovecot AND postfix? or are they the same thing? dovecot does not show up anywhere in webmin what i cant seem to figure out how to do is add a user email so i can try to telnet in on port 143. i think i have evrything installed, just need the next step.... sorry for the newb question

  Read the article

• Jetty8 virtual hosts

  - by Martin

  I have a server JAR that is deployed once per customer, it is the API server for their software package. To that end, the port for each API instance must be the same, so that anything programmed against it can always find it. Each instance is deployed on a different domain name The problem I'm having is that, even when using a SelectChannelConnector and setting the host property, I can't get two instances to run simultaneously, I get a BindException with "Address already in use". I suppose my question is: can Jetty do this, or do I need to do some external re-writing, or is there a better way I can go about achieving the same ends? Thanks.

  Read the article

• What's wrong with my MAC address?

  - by Shaul

  I have a D-Link DSL-2650U router, and exactly one computer on the network. For reasons of port forwarding I want to give my computer a static internal IP address, so that I don't take the chance of losing my NAT settings every time the computer reboots. So here's a screen shot that summarizes the entire problem: WTH is wrong with my MAC address? It's copied and pasted from the command prompt window! I tried editing out the dashes, but it still doesn't work. Am I doing something wrong, or is there a bug in the D-Link firmware?

  Read the article

• Unable to connect to Cygwin from Mac OS X by ssh

  - by skyjack

  I've started ssh server on Windows 7 using Cywgin and I'm trying to connect to it by ssh from Mac OS X Mavericks. It fails with next error: ./ssh username@hostname -v OpenSSH_6.6, OpenSSL 1.0.1g 7 Apr 2014 debug1: Reading configuration data /usr/local/etc/ssh/ssh_config debug1: Connecting to hostname [my ip] port 22. debug1: Connection established. debug1: identity file /Users/skyjack/.ssh/id_rsa type -1 debug1: identity file /Users/skyjack/.ssh/id_rsa-cert type -1 debug1: identity file /Users/skyjack/.ssh/id_dsa type -1 debug1: identity file /Users/skyjack/.ssh/id_dsa-cert type -1 debug1: identity file /Users/skyjack/.ssh/id_ecdsa type -1 debug1: identity file /Users/skyjack/.ssh/id_ecdsa-cert type -1 debug1: identity file /Users/skyjack/.ssh/id_ed25519 type -1 debug1: identity file /Users/skyjack/.ssh/id_ed25519-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.6 ssh_exchange_identification: read: Connection reset by peer Meanwhile I can connect successfully from Red Hat. OpenSSH version on Cygwin: OpenSSH_6.4p1, OpenSSL 1.0.1f 6 Jan 2014 OpenSSH version on MAC OS X: OpenSSH_6.6p1, OpenSSL 1.0.1g 7 Apr 2014 Please advice.

  Read the article

• rdesktop + seamlessrdp + virtualbox slow on Windows

  - by Claudiu

  I'm trying to get VirtualBox seamless mode to work on all of my monitors at once. I was directed to this link, so I followed the instructions, using the windows port of rdesktop 1.6 found here, and using Xming as an X server. I eventually finally got it to work! However, it's really slow. While VirtualBox's regular seamless mode is as performant as if I was running apps on my host machine, with rdesktop it takes 1-2 seconds to register any user input. Dragging windows around is laggy and buggy (pieces of the desktop behind the window show through). I'm simply connecting to localhost, so network bandwidth/latency shouldn't be an issue... anyone have any idea why it's so slow and what I can do to make it more performant?

  Read the article

• DHCPOFFER delay VLAN

  - by john883

  I have configured two VLANs [ 15 and 16 ] and a trunkport on a Cisco Catalyst 2960. The trunkport is connected to eth2 on a Linux server The server is configured to support VLAN's and the interfaces eth2.15 eth2.16 is configured with ip addresses on two different subnet. dhcp3-server is running on the same server and hands out IP-addresses to the VLANs. When connecting a client to a port that is configured in ex. VLAN 15 and requesting a IP-address, i experience a long delay before recieving a DHCPOFFER, around 30 seconds or so, the client needs to send a DHCPDISCOVER about five times but will always recieve a DHCPOFFER. Any suggestion why this delay is happening?

  Read the article

• client subscribed to a multicast group not receiving data

  - by Abruzzo Forte e Gentile

  I have a network that was setup for multicast traffic IN Machine A there is a server application generating multi-cast traffic. I have also different clients subscribing to that mulicast traffic -some client are in the same machine A -other clients are in machine B,C,D # Address I am using IP : 239.193.0.21 PORT: 20401 I don't know why but the client in machine A , even if they join the group, don't receive any data while (and this is the funny part) machine B,C and D receive everything. Checking with Wirshark I can see that the UDP traffic flow is there in Machine A. I am using LInux/Red-Hat Enterprise 6.2 What should I look at? Any setting in the os? Firewall or what?

  Read the article

• Empty sshd_config file

  - by Thomas

  I run a Centos 5 server with a LAMP stack. I was told this morning that the server was down not serving web content. I then tried to restart httpd but it failed due to another process was listening on port 443. I checked what process was running on 443 using netstat and it was sshd. I then checked the sshd_config file to check the ports that sshd was running on but the sshd_config file was completely blank. I than ran chkrootkit and it flagged not suspicions. What could of caused the sshd_config file to be blank, and sshd service to be restarted? I would really value your thoughts. All the best.

  Read the article

• connect to a headless virtualbox instance in Linux?

  - by 130490868091234

  I've started a headless virtualbox instance with this command: VBoxManage startvm "Ensembl67VirtualMachine" --type headless Waiting for VM "Ensembl67VirtualMachine" to power on... VM "Ensembl67VirtualMachine" has been successfully started. It is set up with Remote Desktop Server Port:5555 with Authentication Method: Null and Extended Features: Allow Multiple Connections and it's now running, but I don't know how to connect to it from the same laptop where it's running. I would like to be able to have it running on a terminal. I tried this but nothing happens: rdesktop localhost:5555 ERROR: localhost: unable to connect rdesktop 192.168.1.1:5555 Any ideas?

  Read the article

• Cable installed - now my hub has no connection the router/modem - what do I need to buy?

  - by bcmcfc

  My previous setup was as follows: [modem/router]------[switch]+------ [pc1] +------ [pc2] I've just moved and had cable installed and I no longer have the option of running a lengthy LAN cable from the router to the switch to provide network and internet access to the two PCs. The cable company provided 2 wireless N USB adapters. What do I need to buy to plug into where in order to restore the network to its previous state? PC1 dual boots Windows 7 and Ubuntu 12. PC2 runs Debian 6. Edit: USB adapters - Netgear WNDA3200 Switch - TP-Link TL-SF1008D 8 port Ethernet switch Cabling - various patch cables cat5e rj45 Modem/Router - pretty standard cable company job - wireless Intention is something like- [modem/router] --wifi-- [some-new-hardware or perhaps to pc1] ----[switch]---[pc1/2]

  Read the article

• OpenVPN route missing

  - by dajuric

  I can connect to an OpenVPN server from Windows without any problems. But when I try to connect from Ubuntu 12.04 (start OpenVPN) I receive the following: OpenVPN needs a gateway parameter for a --route option and no default was specified by either --route-gateway or --ifconfig options SERVER IP: 161.53.X.X internal network: 10.0.0.0 / 8 What I need to do ? client configuration: client dev tap proto udp remote 161.53.X.X 1194 resolv-retry infinite nobind ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3 server conf: local 161.53.X.X port 1194 proto udp dev tap dev-node OpenVPN ca ca.crt cert server.crt key server.key # This file should be kept secret dh dh1024.pem # DHCP leases addresses to clients server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. push "route 10.0.0.1 255.255.0.0" client-to-client duplicate-cn keepalive 10 120 comp-lzo verb 6

  Read the article

• How can I set up VLANs in a way that won't put me at risk for VLAN hopping?

  - by hobodave

  We're planning to migrate our production network from a VLAN-less configuration to a tagged VLAN (802.1q) configuration. This diagram summarizes the planned configuration: One significant detail is that a large portion of these hosts will actually be VMs on a single bare-metal machine. In fact, the only physical machines will be DB01, DB02, the firewalls and the switches. All other machines will be virtualized on a single host. One concern that has been is that this approach is complicated (overcomplicated implied), and that the VLANs are only providing an illusion of security, because "VLAN hopping is easy". Is this a valid concern, given that multiple VLANs will be used for a single physical switch port due to virtualization? How would I setup my VLANs appropriately to prevent this risk? Also, I've heard that VMWare ESX has something called "virtual switches". Is this unique to the VMWare hypervisor? If not, is it available with KVM (my planned hypervisor of choice)?. How does that come into play?

  Read the article

• What do I need to connect a hard disk to my laptop via non powered eSata?

  - by Ludo

  Hi there. I'm looking at getting a hard disk for my laptop (OCZ Vertex 2 SSD) which I would like to connect via eSata. My laptop has an eSata port, but it's not powered (Thinkpad T410). I presume this means I need more than just an eSata to eSata cable as it needs power, so does this mean I need a caddy for the hard disk as well which will provide power to the drive, or do I need one of them eSata cables that has a USB attachment too? I don't think the drive will come with a power supply. I realise this seems simple but I can't find an obvious answer online. Thanks for any assistance! Ludo.

  Read the article

• How to get external 2.5 inch HD enclosure get recognised

  - by fireBand

  I am completely out of ideas. I have 2.5inch HDD from my old laptop, I have tried with 2 different HDD enclosures but my desktop does not recognize it. Not even showing in the disk management or BIOS. The HDD works fine if I use in a 3.5 inch enclosure with external power. I have tried 3 different Y USB cables. I have also got a 7 port self powered 2A USB hub. I have updated my chipset drivers as well. The problem is with my desktop , the enclosures work fine with my new laptop. Anything else that I should try? Thanks in advance.

  Read the article

• Monitor Bonded Interface for Disconnection

  - by bradlis7

  I am trying to monitor for network failures on a machine, and one portion of that is to monitor interfaces that are intended to be active also be "RUNNING". An Ethernet port, such as eth0, will say "RUNNING" if it is physically connected to another device. The problem lies in the bonded interfaces, such as bond0. If all of the ethernet devices are disconnected, it still says that it is running, and it is still pingable. Is this by design, or is my system setup incorrectly? Does the miimon option have something to do with this?

  Read the article

• Ctrl W s not splitting windows in vim

  - by rajan sthapit

  I am trying to use Ctrl+ws to split a window in vim. However it is not working in my case. I opened a file using vim filename. Then I pressed Ctrl+ws. But as soon as I press just Ctrl+w it clears the viewport and I could see my shell display before vim opened the file. I mean the view port is replaced by the content just before the file was opened. However, I am still editing the file with vim. Suggestions?

  Read the article

• How to connect MySQL database of local server in NetBeans 7.0.1 ( windows)?

  - by diEcho

  Hello All, I am using NetBeans IDE 7.0.1 on Windows 7 very first time for my php. Actually in my company there is a local server ( 192.168.1.99) where all projects resides and we access phpmyadmin of that local server, Although I have added my project folders with NetBeans (this was also very hectic) but now I am having problem to connect database of my local server as I can see 192.168.1.99/phpmyadmin through my browser. I have set below value Server Host : localhost, Server port number : 3306, Administrator username : keshav Administrator password : ****** and when i click on connect, a popup error windows appears with below text Unable to connect to the MySQL server: org.netbeans.api.db.explorer.DatabaseException: org.netbeans.api.db.explorer.DatabaseException: java.sql.SQLException: Access denied for user 'keshav'@'localhost' (using password: YES). The server may not be running or your MySQL connection properties may not be set correctly. Do you want to edit your MySQL connection properties? Please help me out. Thanks

  Read the article

• Server 2008 R2 Remote Desktop Gateway Role and IIS7

  - by user137466

  I am attempting to setup a RD Gateway for a client. When I first set it up I noticed that IIS did not have the 'Defualt Web Site' so I created it and assigned it an id of 1 and set the bindings to port 80 and 443. I then re installed the RD Gateway role with the idea that it would then configure IIS correctly. It did not. How would I go about making sure a re install of the Remote Desktop Gateway role configures IIS correctly? I cannot re install IIS as there is a site that is already on there that I cannot take down

  Read the article

< Previous Page | 334 335 336 337 338 339 340 341 342 343 344 345  | Next Page >