Search Results

Search found 9340 results on 374 pages for 'andy boot'.

Page 339/374 | < Previous Page | 335 336 337 338 339 340 341 342 343 344 345 346  | Next Page >

• Ubuntu 12.04 on VMware Player loses network configuration

  - by d4ryl3

  I've been having this issue for 2 weeks now with my VMware Player-hosted Ubuntu 12.04. I only use it for my LAMP stack. I've had no issues with it before until about 2 weeks ago when it almost always (once per day at least) loses its network configuration. On boot it shows: Waiting for network configuration... Waiting up to 60 more seconds for network configuration... Booting system without full network configuration... Then when I do ifconfig -a it doesn't show an IP Address and couldn't get online. The only resolutions I've found so far was either to reinstall VMware Tools or use the VMware Player installer and choose Repair. This is frustrating to me because even when the issue was resolved after doing either of the steps I mentioned, the IP Address gets changed. Then I'd have to update the Remote Configuration of my IDE (Netbeans) and my database manager. What could possible cause this? Please help. Thank you. Additional details: I'm using a laptop with Windows 7 and connected to the office WiFi, which is unrestricted as far as I know. Thanks again.

  Read the article

• Tomato OS: "memory exhausted" running vi .... how to solve?

  - by Sam Jones

  I have set up tomato (shibby) on an asus RT-N66U router. It works great. I loaded up a few pieces, like transmission and optware. I can run vi, but when I run vi it fails with a "memory exhausted" error, and the terminal session hangs. For reference: If I simply start "vi" it runs fine. But if I specify vi I get the memory exhausted error, even if the file I am opening is just a couple of hundred bytes in size (like fstab). I discovered that my swap partition was not properly set up, so I did that. The swapon command now indicates I really do have a swap: [root@MyRouter samba]$ swapon -s Filename Type Size Used Priority /dev/sda1 partition 32900860 0 1 How can I get vi to work? Thanks! System setup reference information: asus RT-N66U router 2TB usb hard drive partitions on hard drive: Disk /dev/sda: 2000.4 GB, 2000398839808 bytes 255 heads, 63 sectors/track, 30400 cylinders Units = cylinders of 16065 * 4096 = 65802240 bytes Disk identifier: 0xfacbc8ab Device Boot Start End Blocks Id System /dev/sda1 1 512 32900868 82 Linux swap / Solaris /dev/sda2 513 29000 1830638880 83 Linux running samba memory: $ cat /proc/meminfo MemTotal: 255840 kB MemFree: 210980 kB Buffers: 5264 kB Cached: 22768 kB SwapCached: 0 kB Active: 20272 kB Inactive: 11448 kB HighTotal: 131072 kB HighFree: 99868 kB LowTotal: 124768 kB LowFree: 111112 kB SwapTotal: 32900860 kB SwapFree: 32900860 kB Dirty: 0 kB Writeback: 0 kB TIA!

  Read the article

• Need clear steps on how to convert a Windows 2000 Server to a XenServer VM

  - by Jay

  The source system is not local. The target host running XenServer is not local. The source system is running Windows 2000 Server SP4 and has 1 disk split into 6 partitions, all NTFS: C: 6 GB (boot) D: 15 GB E: 6 GB F: 6 GB G: 5 GB H: 26 GB Most of the partitions are mostly mostly full ( 60%). What is the most straightforward way to do a P2V migration of the server? I can do minor database & data syncs after the P2V is successful & running as a VM within XenServer, it's just getting to that point which is not clear. The option of installing a Windows 2000 Server from scratch is not available, I need to convert the existing physical server as-is into a VM to be hosted within a XenServer environment. I've looked at XenConvert but it maxes out on converting only 4 partitions in one shot, and I'm not certain how to account for the 2 extra partitions. I'm not familiar with XenServer but it's my only option right now to go P2V.

  Read the article

• Logic behind SCCM 2012 required PXE deployments

  - by Omnomnomnom

  I'm in the process of setting up Windows 7 deployment through PXE boot, with Microsoft SCCM 2012. The imaging itself works very well, but I have a question about the logic behind PXE deployments. My setup is the following: My Windows 7 deployment task sequence is deployed to the unknown computers group. (not required, press F12 to start installing) OSDComputerName variable is also set on the unknown computers group, so unknown computers that are being imaged will prompt for a pc name. The computer then becomes known in SCCM and is added to the correct collection(s). But if I want to reïnstall windows on a known computer things are different: I can do a required deployment of the imaging task sequence to the collection of computers. Then windows installs through PXE, without any human interaction, keeping the original computer name. But because the initial deployment was not required, the "required PXE deployment" flag is not set. So as soon as I add a new computer to a collection with a required PXE deployment, it will start to reïnstall windows again. I can also deploy the imaging task sequence to the new unknown computers as required, so the flag gets set initially. But then it does not prompt for a computer name. (and it generates a name like MININT-xxx) Which is also sort of what I want. Because when i want to re-install a machine, I want it to install without interaction. How can I solve this?

  Read the article

• IPv4 not enabled in Windows 7

  - by RidDeBakTiYar

  I have a Netbook with Win 7 Starter edition. I am not able to get IPv4 enabled/installed in the Netbook and hence not able to network/connect to Internet. It says "Limited access" when I check connections. It all began when my system crashed and I was not able to get thro beyond the boot screen. The system advice me to try repair with the original OS cd and I did the same. After that the Netbook has booted, but is not able to network. On a detailed study I found that the Network adapter has both IPv4 and IPv6 Protocols, but there are some differences. The IPv4 is not having the "Properties" enabled to configure, while the IPv6 is having "Properties" enabled. I have only a IPv4 Wired and Wireless at home and its not able to get the Netbook connected as it cannot I had tried uninstalling the Adapter to allow windows to automatically detect and install. Using the "netsh" command to uninstall and install, but not having any change in status. There is a option to "Have disk" under add Protocol, but I don't know how to give the standard IPv4 for installation (asking for *.inf). Any help in solving the issue will be very much appreciated

  Read the article

• Can you "swap" the Sysprep answer file in Windows 7

  - by Ben

  I have a load of new Lenovo laptops which I am due to distribute in my company. We are distributed in multiple locations and I want to ship the laptops "boxed" and untouched by IT hand for distribution. We are using LANDesk to do all the software distribution and provisioning, but are currently falling at the first hurdle as when booted, the laptops kick into the Lenovo mini-setup wizard. I assume this is because they have been sysprepped at Lenovo. In order to keep with our (almost) zero touch strategy I want the users to PXE boot into a PE of some sort, which will run a script on startup which replaces the sysprep answer file with one of my own. (i.e. prepopulated with product key, company info etc.) and then reboot to complete Sysprep. The plan is that this will run, and then install the LANDesk agent as a post-sysprep task, which in turn will complete the provisioning. Anyone have any experience / know any pitfalls to look out for / can suggest a suitable, PXE-bootable PE environment? Apologies for the verbosity of the question - it takes a bit of explaining! Thanks in advance, Ben

  Read the article

• how to correctly mount fat32 partition in Ubuntu in order to preserve case

  - by Dean

  I've found there are couple of problems might be related how my FAT32 partition was mounted. I hope you can help me to solve the problem. I also included the command I used to help others when they find this post, sorry to those might feel I should use less space. I've the following file structures on my disk dean@notebook:~$ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x08860886 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 5737 45978624 7 HPFS/NTFS /dev/sda3 5738 10600 39062047+ 83 Linux /dev/sda4 10601 19457 71143852+ 5 Extended /dev/sda5 10601 11208 4883728+ 82 Linux swap / Solaris /dev/sda6 11209 15033 30720000 b W95 FAT32 /dev/sda7 15033 19457 35537920 7 HPFS/NTFS In the etc/fstab I've got UUID=91c57a65-dc53-476b-b219-28dac3682d31 / ext4 defaults 0 1 UUID=BEA2A8AFA2A86D99 /media/NTFS ntfs-3g quiet,defaults,locale=en_US.utf8,umask=0 0 0 UUID=0C0C-9BB3 /media/FAT32 vfat user,auto,utf8,fmask=0111,dmask=0000,uid=1000 0 0 /dev/sda5 swap swap sw 0 0 /dev/sda1 /media/sda1 ntfs nls=iso8859-1,ro,noauto,umask=000 0 0 /dev/sda2 /media/sda2 ntfs nls=iso8859-1,ro,noauto,umask=000 0 0 I checked my id using id and I've got dean@notebook:~$ id uid=1000(dean) gid=1000(dean) groups=4(adm),20(dialout),24(cdrom),46(plugdev),103(fuse),104(lpadmin),115(admin),120(sambashare),1000(dean) I don't know why with these settings I still have problem of using svn like in this one Thank you for your help!

  Read the article

• GTX 280 purple snow on bootup, card works without drivers

  - by Brokar

  i have owned a ASUS GTX280 for 3 years now. The card has been great all along but i started having problems 10 days ago. I was playing Diablo 3 for 1 week on max settings no problems, then suddenly my display kept getting some weird purple/colours as soon as i booted and logged into windows. Went into safe mode, updated drivers and it kept crashing. Formatted PC, fresh windows install with new WHQL drivers again same problem. Uninstalled nvidia drivers and pc has been running great for 4 days now, ofcourse i cannot run games but everything works on 1680x1050 resolution and i can browse internet,watch movies and use my PC for everything but gaming. As soon as i install nvidia drivers PC won't boot. I only wanna game a few hours a week (very busy program with school this month so it might be a blessing that i cannot game) and i would love it if i could keep the card. I am looking to upgrde later on when i will have time for gaming but i wonder if i could still use the card somehow with different/new drivers (tried older drivers that came with the card on a CD aswell) tldr: PC works fine with no nvidia drivers (apart from gaming ofc). Once i install WHQL drivers or older ones, cannot even log into windows. Fix?

  Read the article

• mysql startup, shtudown and logging on osx

  - by Joelio

  Hi, I am trying to troubleshoot some mysql problems (I have a table I cant seem to delete or drop, it hangs forever) I have 10.5.8 osx, I dont remember how/if I installed mysql, here is what I know: it automatically starts on boot the process looks like this: /usr/local/mysql/libexec/mysqld --basedir=/usr/local/mysql --datadir=/usr/local/mysql/var --pid-file=/usr/local/mysql/var/Joels-New-Pro.local.pid _mysql 96 0.0 0.0 75884 684 ?? Ss Sat06PM 0:00.02 /bin/sh /usr/local/mysql/bin/mysqld_safe when I run: /usr/local/mysql/libexec/mysqld --verbose --help it says: /usr/local/mysql/libexec/mysqld Ver 5.0.45 for apple-darwin9.1.0 on i686 (Source distribution) it seems to use my.cnf from /etc/my.cnf Now here are my questions: I dont see anything in the startupitems that remotely looks like mysql ls /Library/StartupItems/ BRESINKx86Monitoring ChmodBPF HP IO HP Trap Monitor Parallels ParallelsTransporter 1.) So how does it startup automatically? 2.) How do I start & stop this type of installation? Also, looking at the config, the logs have no values: /usr/local/mysql/libexec/mysqld --verbose --help|grep '^log' log (No default value) log-bin (No default value) log-bin-index (No default value) log-bin-trust-function-creators FALSE log-bin-trust-routine-creators FALSE log-error log-isam myisam.log log-queries-not-using-indexes FALSE log-short-format FALSE log-slave-updates FALSE log-slow-admin-statements FALSE log-slow-queries (No default value) log-tc tc.log log-tc-size 24576 log-update (No default value) log-warnings 1 3.) Does that mean there is no logging enabled in mysetup? thanks in advance! Joel

  Read the article

• DD-WRT router causing IP address conflicts across network

  - by r.tanner.f

  My DD-WRT router has lost its mind! I just set up two DD-WRT routers, one as a WAP (working fine) and one in Client Bridge (routed) mode (the problem). Not long after setup I started seeing IP address conflicts on other machines. The event log always points the finger at my Client Bridge router's MAC address. Neighbour table overflow The log on my router is flooded with Neighbour table overflow errors. These start a minute or two after boot. The network is rather large, with +200 IP addresses being used in this subnet. The other router shows no such errors. Mass ARP requests from 1.1.1.1 I'm also seeing constant ARP requests (with the problem router's MAC address) from 1.1.1.1. Seems like it's bugging everything on the network for its MAC address and then promptly forgetting it (or never receiving a response). Configuration: Model: Buffalo N600 Firmware: DD-WRT v24SP2-MULTI (03/21/11) Wireless Mode: Client Bridge (routed) I'm not sure what configuration details are relevant and I'd rather not have comments flooded, so just ping me in this chat if you want to know something. Why is my router stealing IP addresses and how can I stop it?

  Read the article

• Looking for a comprehensive/"expert" guide to BCD parameters

  - by Stilez

  I'm interested in educating myself about BCD on Windows 8. There are many, many "walkthrough" guides" and "howtos", but I can't find any guides at typical "enthusiast" level covering what each option or argument in a BCD /ENUM dump might mean, and the principles governing how these all work together. Imagine trying to rebuild or debug BCD (including EFI/BIOS variants and recovery/hibernate/memtest sections, and perhaps multiple boot Windows/WinPE/WinRE) from scratch using just BCDedit + DiskPart, and trying to understand rather than just copy/pasting commands. That's roughly the knowledge I'm after. Example questions might be: How is a BCD /ENUM dump to be read, item by item? How do its sections work together? (A lot of guides only show a specific example rather than explaining all the all common args that can exist and what they mean, they don't actually explain how sections work together, or they assume MBR/BIOS/Vista/7 and omit info needed for EFI/GPT/Dynamic disks/8) Partitions are specified by volume letter or as a \Device\HarddiskVolumeNNN. Why does it sometimes show these items as a letter and sometimes as a GUID? What are the practical differences if any? What exactly is syntax like "ramdisk=[C:]\Images\winpe.wim,{ramdiskoptions}" saying, and how will the drive letter "C" be interpreted at runtime in a line like this? Is the drive in such a line always "C:" (most examples assume so) and if not, when wouldn't it be? Many websites state that an sdi device and path may be needed in some sections of BCD, but what is sdi and what are these args doing when they appear? How does the GUID to HDD volume/partition mapping work under EFI/GPT? So that if disks or partitions/volumes change it's clear how one can confirm from basic principles whether data shown in BCD /ENUM ALL is still correct or not. Does anyone know of a suitable reference source for this kind of raw BCD data and structures? Thanks!

  Read the article

• My hard drive seems to be overheating... what should I do?

  - by George Edison

  After a cold boot, the hard drive in my notebook jumps to 56? within an hour or so of idling. Is 56? a cause for alarm? Notes: The notebook is on a flat desk and none of the vents are obstructed. The video card is currently at 55? and the CPU at 50?. It's a Western Digital 250GB hard drive. SMART reports the drive healthy but does warn that: Edit: this problem had a very surprise ending. I inverted the notebook and unscrewed some of the panels on the back (there was one covering the hard drive, and one that provided access to the memory). I couldn't see any dust, so I simply screwed everything back together and powered it on... and it worked! The temperature is now staying at 46?, and it feels notable cooler to the touch. So I can only assume that some internal fan was malfunctioning or something. Whatever the case, it's working now so I won't complain. Edit: I have an SSD now, so temperature isn't as big an issue as it was when I had a mechanical drive.

  Read the article

• Cannot connect to server via SSH

  - by Rayne

  I'm running RHEL 6.0, and I accidentally moved the /bin, /boot, /cgroup, console.txt, /data, /dev, /etc to another folder. I think I managed to move these folders back, but now I'm having trouble connecting to the server using SSH, but am able to access the server via VNC. When I tried to connect to the server using a terminal from another server, I get the error ssh_exchange_identification: Connection closed by remote host I'm currently still connected via SSH to the server (haven't closed the window yet), and am still able to access it normally. But if I try to open a new SSH terminal from my current session, I see /bin/bash: Permission denied If I try to open a new SSH File Transfer window from my current session, I get the error File transfer server could not be started or it exited unexpectedly. Exit value 0 was returned. Most likely the sftp-server is not in the path of the user on the server-side I checked and I have Subsystem sftp /usr/libexec/openssh/sftp-server which is the same path as the output of locate sftp-server Also, when I tried to restart sshd, I get the error Couldn't open /dev/null: Permission denied But my /dev/null has the permissions crw-rw-rw- for root,root. How can I resolve this? ETA: Thanks for all your help! I was able to start ssh by running the application directly /usr/sbin/sshd Even though the status of the openssh-daemon is still "stopped".

  Read the article

• How to bypass resume from hibernate

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• Lightweight Linux distro that includes developer tools? (or, the most BSD-like Linux)

  - by RevAaron

  I cut my teeth on Minix and Slackware 1.1, but I've been in the OS X Wilderness for the last few years. I'm trying to standardize on a Linux distribution for personal and work-related use on less powerful laptops and under virtualization. So far, NetBSD and OpenBSD are the best fit for my purposes- but after plenty of frustration I've come to the conclusion that I need to stick with Linux to get the hardware and software support that comes with it. What I like about NetBSD/OpenBSD that I'd like to keep: X, but no default KDE, GNOME or XFCE! A sensible /etc and dot file setup- startx calls xinit, xinit looks for ~/.xinitrc; nothing more complicated than that is needed. Command line tools and file-based configuration: I shouldn't need a GUI to connect to a WAP. Decent selection of binary packages; building from source is OK, but nothing source-only like Gentoo. pkg_add (BSD) and apt-get both have treated me well in the past. Modest RAM and HDD requirements: boot + X + awesome+ two xterms takes up 80 MB on OpenBSD and 240 MB on Debian 5 and Crunchbang In my experience, most "lightweight" and Live CDs focus on a nice desktop environment crammed into a CD or USB stick; once you add build-essentials you end up with something just about as bloated as Ubuntu or Debian full install. Crunchbang is a great example. Thanks in advance for all suggestions!

  Read the article

• ZFS: Mirror vs. RAID-Z

  - by John Clayton

  I'm planning on building a file server using OpenSolaris and ZFS that will provide two primary services - be an iSCSI target for XenServer virtual machines & be a general home file server. The hardware I'm looking at includes 2x 4-port SATA controllers, 2x small boot drives (one on each controller), and 4x big drives for storage. This allows one free port per controller for upgrading the array down the road. Where I'm a little confused is how to setup the storage drives. For performance, mirroring appears to be king. I'm having a hard time seeing what the benefit would be of using RAIDZ over mirroring would be. With this setup I can see two options - two mirrored pools in one stripe, or RAIDZ2. Both should protect against 2 drive failures, and/or one controller failure...the only benefit of RAIDZ2 would be that any 2 drives could fail. The storage should be 50% of capacity in both cases, but the first should have much better performance, right? The other thing I'm trying to wrap my mind around is the benefit of mirrored arrays with more than two devices. For data integrity what, if any, would be the benefit of a RAIDZ over a three-way mirror? Since ZFS maintains file integrity what does RAIDZ bring to the table...doesn't ZFS's integrity checks negate the value of RAIDZ's parity?

  Read the article

• Cannot login to Windows7 in normal mode but can in safe mode

  - by Guy

  I have a Windows 7 Ultimate computer (Shuttle) that I built myself and in it I put a Solid State Drive (SSD). It's been working well for a number of months but now when I start it there are problems. I have 2 users setup on the computer and when I try and sign in with either user it claims that the password is incorrect. I could understand the odd typo but I've had my wife try it as well and we've got the passwords correct. On top of that it will remain at the login screen for 1 minute and 20 seconds and then spontaneously reboot without shutting down. So I'm trying to work out if this is a hard disk problem or something else. Any ideas? (I have a nightly backup to a WHS so it will be easy to recover but I don't want to do that unless I have to and don't want to waste time putting in a new HD just to discover it's something else.) More info: If I start in Safe Mode I am able to login with the password and all appears as normal as it can in Safe Mode. However, normal boot continues with same problem.

  Read the article

• Backup, Migrate or Clone Failing CentOS 4 (LVM)

  - by Hegelworm

  Hello there, I've been running a BlueQuartz CentOS 4 system (Nuonce.net distro) for a few years now and although the hard drive (Deskstar) has always been a bit noisy, on a few recent occasions I've heard it having trouble spinning up. Basically, I want to clone this drive to a similar sized one (80 Gig). I've spent many hours reading upon dd, dd_rescue, rsync, clonezilla and LVM mirroring yet the sheer number of options and nightmarish accounts has left me frozen - unable to make an informed decision as to how to start. I've made a few attempts. dd failed after about 2 hours, as, although the drives appeared to be identical on the surface (ATA Seagate Barracudas, Thai not Chinese), the destination drive is slightly smaller. My most recent attempt involved using a Debian CD to format the new drive and then rsync-ing everything over and editing the new drive's grub and fstab to reflect the changes. No joy here either as I hadn't chosen LVM when partitioning the destination drive and it wouldn't boot. As you can probably tell, I'm out of my depth here and a panic-invoking mixture of caution and frustration has prompted me to sign up here. The server itself, although not strictly a production environment, has a very specific installation of Festival, LAME and ffMpeg and provides the back-end for a Text-to-Speech jQuery plugin that I've built over the last 2 years. I'm also planning to rebuild the whole TTS system on Debian as the existing CentOS system still has PHP4 etc. For now though, I'd really like to just shift everything over to a new drive. As this is my first post, please feel free to lay any house rules on me that I might've overlooked; I've been hovering around StackOverflow for a while now but have only just signed up. Many thanks.

  Read the article

• WIM2VHD failing with "Cannot derive Volume GUID from mount point."

  - by Jacob

  I'm trying to use WIM2VHD according to the instructions on Scott Hanselman's blog post to create a Sysprepped VHD image to boot from. I've installed the WAIK, and I have my Windows 7 sources mounted as a virtual drive. When I try to run WIM2VHD like this: cscript WIM2VHD.wsf /wim:F:\sources\install.wim /sku:Ultimate /vhd:E:\WindowsSeven.vhd /size:30721 I get the following log: Log for WIM2VHD 6.1.7600.0 on 11/2/2009 at 10:51:18.16 Copyright (C) Microsoft Corporation. All rights reserved. MACHINE INFO: Build=7600 Platform=x86fre OS=Windows 7 Ultimate ServicePack= Version=6.1 BuildLab=win7_rtm BuildDate=090713-1255 Language=en-ZA INFO: Looking for IMAGEX.EXE... INFO: Looking for BCDBOOT.EXE... INFO: Looking for BCDEDIT.EXE... INFO: Looking for REG.EXE... INFO: Looking for DISKPART.EXE... INFO: Session key is E01E1ED7-C197-4814-BDE4-43B73E14FCC4 INFO: Inspecting the WIM... INFO: Configuring and formatting the VHD... ******************************************************************************* Error: 0: Cannot derive Volume GUID from mount point. ******************************************************************************* INFO: Unmounting the VHD due to error... WARNING: In order to help resolve the issue, temporary files have not been deleted. They are in: C:\Users\Jacob\AppData\Local\Temp\WIM2VHD.WSF\E01E1ED7-C197-4814-BDE4-43B73E14FCC4 *emphasized text*Summary: Errors: 1, Warnings: 1, Successes: 0 INFO: Done. Any ideas?

  Read the article

• Install Ubuntu 10.10 from loopback mounted ISO image

  - by Zifre

  I have a laptop with a faulty BIOS that has stopped booting from CDs even though it supports it (and it doesn't support booting from USB drives). I am trying to install Ubuntu 10.10 on it. I already had 9.10 installed. I tried using Kexec, but it refused to accept the kernel image. Eventually I found this page which shows how to make GRUB 2 boot from an ISO file. That worked fine, and I am now running the live image from the file. (If I can get this to work, it will be my new preferred way of installing Ubuntu, as it saves CDs and boots much faster.) However, I can't install it. The installer won't make changes to the hard drive, because the partition containing the ISO is mounted (and can't be unmounted because it is in use). Even if I only choose to use other partitions that are not mounted, the installer refuses to go any farther. Clearly, it should be possible using other partitions on the same disk. Is there any way to work around this issue or force the installer to go ahead?

  Read the article

• Can I have a single solid state drive and a RAID array on the same machine?

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Wireless disconnect randomly with wpa_supplicant reason=2

  - by renenglish

  I installed ubuntu-server 12.04 on my PC , and I use an usb wireless card to join the network. It works ok when I boot up my PC , but the wireless disconnects after a while. I pkill wpa_supplicant and reload the driver rtl8192cu , then it works a again. Then it disconnect again after about a random minutes. Here is the syslog: 22384 May 29 21:49:27 homecenter kernel: [ 6450.459313] wlan1: authenticated 22385 May 29 21:49:27 homecenter kernel: [ 6450.459535] wlan1: associate with f4:ec:38:45:62:74 (try 1) 22386 May 29 21:49:27 homecenter kernel: [ 6450.469080] wlan1: RX AssocResp from f4:ec:38:45:62:74 (capab=0 x431 status=0 aid=3) 22387 May 29 21:49:27 homecenter kernel: [ 6450.469085] wlan1: associated 22388 May 29 21:49:27 homecenter wpa_supplicant[2342]: Associated with f4:ec:38:45:62:74 22389 May 29 21:49:27 homecenter kernel: [ 6450.481933] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready 22390 May 29 21:49:27 homecenter wpa_supplicant[2342]: WPA: Key negotiation completed with f4:ec:38:45:62:7 4 [PTK=CCMP GTK=CCMP] 22391 May 29 21:49:27 homecenter wpa_supplicant[2342]: CTRL-EVENT-CONNECTED - Connection to f4:ec:38:45:62: 74 completed (auth) [id=0 id_str=] 22392 May 29 21:49:38 homecenter kernel: [ 6461.472014] wlan1: no IPv6 routers present 22393 May 29 21:49:38 homecenter ntpdate[2263]: step time server 91.189.94.4 offset 0.012758 sec 22394 May 29 21:49:51 homecenter ntpdate[2404]: step time server 91.189.94.4 offset -0.001190 sec 22395 May 29 21:54:38 homecenter kernel: [ 6762.052030] wlan1: deauthenticated from f4:ec:38:45:62:74 (Reas on: 2) 22396 May 29 21:54:38 homecenter wpa_supplicant[2342]: CTRL-EVENT-DISCONNECTED bssid=f4:ec:38:45:62:74 reas on=2 22397 May 29 21:54:38 homecenter kernel: [ 6762.064744] cfg80211: All devices are disconnected, going to re store regulatory settings 22398 May 29 21:54:38 homecenter kernel: [ 6762.064752] cfg80211: Restoring regulatory settings 22399 May 29 21:54:38 homecenter kernel: [ 6762.064757] cfg80211: Calling CRDA to update world regulatory d omain 22400 May 29 21:54:38 homecenter kernel: [ 6762.069938] cfg80211: Ignoring regulatory request Set by core s ince the driver uses its own custom regulatory domain 22401 May 29 21:54:38 homecenter kernel: [ 6762.069943] cfg80211: World regulatory domain updated: 22402 May 29 21:54:38 homecenter kernel: [ 6762.069945] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 22403 May 29 21:54:38 homecenter kernel: [ 6762.069949] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22404 May 29 21:54:38 homecenter kernel: [ 6762.069952] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22405 May 29 21:54:38 homecenter kernel: [ 6762.069956] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22406 May 29 21:54:38 homecenter kernel: [ 6762.069959] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22407 May 29 21:54:38 homecenter kernel: [ 6762.069962] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KH z), (300 mBi, 2000 mBm)

  Read the article

• Ballooning Mac OS X kernel_task and Wired memory usage. How to diagnose / fix?

  - by user28930

  I have a very strange issue, which I'm having a hard time diagnosing as to the root cause. I have a Mac Pro (2008, 8-core 2.8 GHz, 8800GT) with 14 GB of RAM (recently upgraded because of this issue!). When I boot my system and log in, vm_stat / top / Activity Monitor will show that kernel_task has about 150 MB allocated, and the machine has about 800 MB of Wired memory being allocated. Even initially, 800 MB seems an awful lot of wired memory to be allocated with no applications running - but, it gets worse. (NB: Wired is locked, unswappable memory) After a very short time, sometimes triggered by something as simple as launching a terminal, kernel_task will balloon to 8-900 MB of Real Mem (RSIZE), and Wired Memory will accelerate to 1.6 GB (implying that all the extra memory requests are for wired RAM in the kernel). If I quit everything (I.E: no running applications, bar an activity monitor or terminal to view top), there is no appreciable reduction in either kernel_task RSIZE, or Wired Memory usage. Going the opposite way, and loading the system with tasks also shows that wired memory does not get reduced - and that importantly it is not reduced in preference to heavy swapping. If I log out and log back in again, it reduces a bit (450 MB kernel_task, 1.28 GB Wired), but not back to the start. I'm not running any wacky kexts - and futhermore, kextstat shows no huge memory allocations there; the largest being com.apple.nvidia.nv50hal at about 4 MB of Memory. The machine feels overall more sluggish when this has happened - unsurprisingly because such a huge amount of RAM has been marked as non-pageable. So I have a few questions: 1) Is there a good way to diagnose what has allocated all of this wired memory? It's often over 2 times the kernel_task size, running no applications. The real memory total doesn't seem to add up - it seems that there is a bunch of RAM that isn't being accounted for anywhere. 2) What is happening to cause the kernel to suddenly require 6 times as much memory?

  Read the article

• Troubleshooting Mid 2007 iMac RAM upgrade

  - by MDT

  I am trying to install new RAM in my friends iMac, something I have done several times before. We unplugged the computer before performing the upgrade, used anti static wrist bands, and yes the memory is compatible and inserted correctly. The stock RAM was Hynix 1gb pc2-5300s-555-12 and the memory we are replacing it with is 2x2gb Centon CMP800SO2048.01. Now I know this model number suggests that the ram is 800MHz and the iMac is only 667MHz but it clearly states on the box that this RAM is PC2-5300 667MHz compatible. The problem is, that when I install the new RAM I get little response from the computer. I hear the hard drive and disk drive start to initialize, but then they just stop and the screen remains black. I have tried every variation of the new RAM and the old RAM in both slots and even tried the same RAM from my old iMac and I just can't get it to boot. Has anyone ever had a problem like this? Thank you in advance for any and all input on thus issue!

  Read the article

• Why is mkfs overwriting the LUKS encryption header on LVM on RAID partitions on Ubuntu 12.04?

  - by Starchy

  I'm trying to setup a couple of LUKS-encrypted partitions to be mounted after boot-time on a new Ubuntu server which was installed with LVM on top of software RAID. After running cryptsetup luksFormat, the LUKS header is clearly visible on the volume. After running any flavor of mkfs, the header is overwritten (which does not happen on other systems that were setup without LVM), and cryptsetup will no longer recognize the device as a LUKS device. # cryptsetup -y --cipher aes-cbc-essiv:sha256 --key-size 256 luksFormat /dev/dm-1 WARNING! ======== This will overwrite data on /dev/dm-1 irrevocably. Are you sure? (Type uppercase yes): YES Enter LUKS passphrase: Verify passphrase: # hexdump -C /dev/dm-1|head -n5 00000000 4c 55 4b 53 ba be 00 01 61 65 73 00 00 00 00 00 |LUKS....aes.....| 00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000020 00 00 00 00 00 00 00 00 63 62 63 2d 65 73 73 69 |........cbc-essi| 00000030 76 3a 73 68 61 32 35 36 00 00 00 00 00 00 00 00 |v:sha256........| 00000040 00 00 00 00 00 00 00 00 73 68 61 31 00 00 00 00 |........sha1....| # cryptsetup luksOpen /dev/dm-1 web2-var # mkfs.ext4 /dev/mapper/web2-var [..snip..] Creating journal (32768 blocks): done Writing superblocks and filesystem accounting information: done # hexdump -C /dev/dm-1|head -n5 # cryptsetup luksClose /dev/mapper/web2-var 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00000400 00 40 5d 00 00 88 74 01 66 a0 12 00 17 f2 6d 01 |.@]...t.f.....m.| 00000410 f5 3f 5d 00 00 00 00 00 02 00 00 00 02 00 00 00 |.?].............| 00000420 00 80 00 00 00 80 00 00 00 20 00 00 00 00 00 00 |......... ......| # cryptsetup luksOpen /dev/dm-1 web2-var Device /dev/dm-1 is not a valid LUKS device. I have also tried mkfs.ext2 with the same result. Based on setups I've done successfully on Debian and Ubuntu (but not LVM or Ubuntu 12.04), it's hard to see why this is failing.

  Read the article

< Previous Page | 335 336 337 338 339 340 341 342 343 344 345 346  | Next Page >