Search Results

Search found 11737 results on 470 pages for 'intel core i7'.

Page 340/470 | < Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >

• Boot error aftter clean Ubuntu 13.04 install: [Reboot and select proper boot device]

  - by IcarusNM

  I am having the same problem as this guy where a fresh Ubuntu install completes beautifully but will not boot. I get the ASUS (?) "Reboot and select proper boot device" error, first with Xubuntu 13.10 and after finally giving up there, and Xubuntu 13.4, I am back to regular Ubuntu 13.4. ASUS motherboard Z77, Intel chipset. Standard internal SATA 500GB HD. 64-bit. All-new hardware less than 3 months old. It was running Ubuntu 12.04LTC great until I tried this upgrade. I have re-installed from scratch every which way: with LVM, without LVM; with the default partitions, with my own partitions. With ext3 or ext4. Alongside; replace; upgrade. No difference. On the last two tries, I have booted afterward from the same USB stick, downloaded and run boot-repair, and now I guess I am off to the boot-repair support email with my URLs from that. It did all kinds of cool stuff but ultimately made no difference. I never got anything like this with Ubuntu 12.04. I've now probably re-installed Ubuntu 13.04 ten times slightly different ways. I finally found how to skip the language packs, so at least that sped things up! :) This starts from the ubuntu-13.04-desktop-amd64.iso and UNetbootin as suggested on the official instructions for USB thumb drive creation from OSX. That part all works fine (booting the USB on the PC and trying Ubuntu and/or installing from there on the PC HD.) I have no CD drive on this PC, but I suppose I could get one. I would rather find some Linux install that works from USB like I've always done. After running boot-repair twice, in the ASUS BIOS I now see three different UEFI boot options in the priority list, and they are all labeled exactly the same: ubuntu (P6: WDC WD5000AAKX-00U6AA0) Then there's a non-UEFI option: P6: WDC WD5000AAKX-00U6AA0 (476940MB) And a fifth option appeared after the first boot-repair: Windows Boot Manager (P6: WDC WD5000AAKX-00U6AA0) I have tried all 5 of these, and I get exactly the same error. I have never had Windows installed on this HD. ASUS is calling it Windows Boot Manaer but I presume that's a mistaken label for whatever boot-repair did. I can boot on USB and run GParted and it looks great. The partitions all look normal. I found another case of this online with no solution posted. I can't find much about it online. Needs a Master Boot Record wipe/redo?? I'm not sure how.

  Read the article

• Is Ubuntu recognizing and/or using my NVIDIA graphics card?

  - by user212860

  This is my first post here, and I'm pretty new to Ubuntu/Linux. I currently have no other OS except for Ubuntu 13.10. (I used to have Win7 until i got a new terabyte hard drive). My current PC build, if any of this helps: CPU: Intel i5 quad-core Graphics: NVIDIA GeForce GTX 650 RAM: 8 GB HDD: 1 TB SATA 3 Motherboard: MSi Z77 A-G41 OS Ubuntu 13.10 So I recently installed Ubuntu 13.10 and put Steam on it, and I'm seeing that my games run a lot slower than they did when I had Win7. I figured it was a graphics problem, so I checked System Settings Details Overview. It says in "Graphics" that I have "Gallium 0.4 on NVE7" (don't really know what that is). Does this mean that Ubuntu is not using my graphics card? In System Settings Software & Updates Additional Drivers, it clearly shows like this: NVIDIA Corporation: GK107 [GeForce GTX 650] -This device is using an alternative driver (And then it shows a list of drivers that I can switch back and forth to) So this is a bit confusing. In Software and Updates, it clearly shows that I have my NVIDIA card installed, and that I have a driver selected for it. But in System Settings, it shows I have some Gallium 0.4 thing. I had done a bit of research, and ended up typing command: "lspci|grep VGA" in the Terminal. It showed this in response: VGA compatible controller: NVIDIA Corporation GK107 [GeForce GTX 650] (rev a1) The Terminal seems to recognize my graphics card. What it looks like to me, is that I don't have the proper driver, and I might be using my CPU's integrated graphics. When I switch around which driver I am using in that list, it still does not see my card in System Settings. Some of the drivers in the list give me some sort of OpenGL error when I try to run a game. It might just be that my games are running slow because the game developers have not optimized it for Ubuntu that well. However, that still doesn't take away from the fact that System Settings is not showing my NVIDIA card. TL;DR Version: How do I know if my video card is being recognized/used? If my video card is not being used, what is the best way fix that? Please make your answers easy to understand. I do not mind wordy responses, as long as I can follow what you're saying. Any help would be greatly appreciated! Thanks, Jabber5

  Read the article

• Why is firefox 4 not HW accelerated?

  - by acidzombie24

  At first i thought it was my computer but then i tried chrome. Why isnt firefox not hardware accelerated? The first screenshot shows chrome at 23% usage. The 2nd shows 59%. I have 2 cpus which is why it isnt 100% usage. The game pictured is biolab Heres the text for about:support Application Basics Name Firefox Version 4.0 User Agent Mozilla/5.0 (Windows NT 6.1; WOW64; rv:2.0) Gecko/20100101 Firefox/4.0 Profile Directory Open Containing Folder Enabled Plugins about:plugins Build Configuration about:buildconfig Extensions Name Version Enabled ID Modified Preferences Name Value accessibility.typeaheadfind.flashBar 0 browser.places.importBookmarksHTML false browser.places.smartBookmarksVersion 2 browser.startup.homepage_override.buildID 20110303194838 browser.startup.homepage_override.mstone rv:2.0 extensions.lastAppVersion 4.0 gfx.font_rendering.directwrite.enabled true network.cookie.prefsMigrated true places.history.expiration.transient_current_max_pages 127602 privacy.sanitize.migrateFx3Prefs true Graphics Adapter Description Mobile Intel(R) 4 Series Express Chipset Family Vendor ID 8086 Device ID 2a42 Adapter RAM Unknown Adapter Drivers igdumd64 igd10umd64 igdumdx32 igd10umd32 Driver Version 8.15.10.2202 Driver Date 8-25-2010 Direct2D Enabled true DirectWrite Enabled true (6.1.7600.16385, font cache n/a) WebGL Renderer Google Inc. -- ANGLE -- OpenGL ES 2.0 (ANGLE 0.0.0.541) GPU Accelerated Windows 1/1 Direct3D 10

  Read the article

• SD Card reader not working on Sony Vaio

  - by TessellatingHeckler

  This laptop (Sony Vaio VGN-Z31MN/B PCG-6z2m) has been installed with Windows 7 64 bit, all the drivers from Sony's VAIO site are installed, and everything in Device Manager both (a) has a driver and (b) shows as working, no exclamation marks or warnings. "Hide empty drives" in Folder options is disabled so the card reader appears, but will not read the card ("please insert a disk in drive O:"). Previously, when the laptop had Windows XP on it, it could read the same card. Also, Windows update suggested driver ("SD Card Reader") doesn't work, Ricoh own drivers install properly but do the same behaviour. Other 3rd party driver suggestions from forums (Acer and Texas-Instruments FlashMedia) do not seem to install properly. I would post the PCI id if I had it, but it was just showing up as rimsptsk\diskricohmemorystickstorage (while it had the Ricoh Driver installed). Edit: If there are any lower level diagnostic utlities which might shed more light on it I'd welcome hearing of them. Anything which might show get it to put troubleshooting logs in the event log or identify chipsets or whatever... Update: Device details are: SD\VID_03&OID_5344&PID_SD04G&REV_8.0\5&4617BC3&0&0 : SD Memory Card PCI\VEN_8086&DEV_2934&SUBSYS_9025104D&REV_03\3&21436425&0&E8: Intel(R) ICH9 Family USB Universal Host Controller - 2934 PCI\VEN_1180&DEV_0476&SUBSYS_9025104D&REV_BA\4&1BD7BFCD&0&20F0: Ricoh R/RL/5C476(II) or Compatible CardBus Controller RIMSPTSK\DISK&VEN_RICOH&PROD_MEMORYSTICKSTORAGE&REV_1.00\MS0001: SD Storage Card PCI\VEN_1180&DEV_0592&SUBSYS_9025104D&REV_11\4&1BD7BFCD&0&24F0: Ricoh Memory Stick Host Controller WPDBUSENUMROOT\UMB\2&37C186B&1&STORAGE#VOLUME#_??_RIMSPTSK#DISK&VEN_RICOH&PROD_MEMORYSTICKSTORAGE&REV_1.00#MS0001#: O:\ STORAGE\VOLUME\{C82A81B8-5A4F-11E0-AACC-806E6F6E6963}#0000000000100000: Generic volume PCI\VEN_1180&DEV_0822&SUBSYS_9025104D&REV_21\4&1BD7BFCD&0&22F0: SDA Standard Compliant SD Host Controller ROOT\LEGACY_FVEVOL\0000 : Bitlocker Drive Encryption Filter Driver PCI\VEN_1180&DEV_0832&SUBSYS_9025104D&REV_04\4&1BD7BFCD&0&21F0: Ricoh 1394 OHCI Compliant Host Controller Now going to search for drivers for that.

  Read the article

• Windows web server and SQL Server on same dedicated server

  - by asinc

  I'm currently trying to decide on the best approach to handle hosting a few moderate traffic websites for production e-commerce and online applications. We'd like to move to a dedicated server and are looking at this as the most likely machine: Quad Core Intel Core2Quad Q9550 Processor, 2.83 Ghz X 4, 4 GB Kingston Ram This would run Windows Web Server 2008 R2 x64 and potentially also Sql Server Web 2008 and SmarterMail server. Given that we already pay for a high-end VPS for development, testing, shared version control we'd like to avoid going with two servers for production. We'd like to avoid using shared sql server hosting and have thought of using the development server as the database server as an option too - but potentially a security risk due to use for development by internal and contract users. The questions are: - Do you feel there would be performance degradation by running this on the same machine? - Are there significant issues to be concerned about if we do this? We understand that best practice would be to run separate db and app servers but the volume of traffic is currently not that high and adding another server just for database is currently too costly. - What are others doing out there? Alternatively, would you recommend instead going with two separate VPS servers with 2GB RAM each on Hyper-v which would be about the same cost as the single dedicated server above? Thanks!

  Read the article

• "0x80004005: Unspecified error" when renaming folders in Windows 7

  - by Michael Steele

  Setup I've just installed Windows 7 Ultimate 64bit. The operating system is installed on an 80GB Intel X-25M. I have a secondary 500GB Barracuda 7200.12 to be used for storage. This second drive is mounted as 'G'. Problem I'm getting an error whenever I try to rename a folder within this drive. The error says: An unexpected error is keeping you from renaming the folder. If you continue to receive this error, you can use the error code to search for help with this problem. Error 0x80004005: Unspecified error Clicking the "Try Again" button gets past the error, and correctly renames the folder. If I create a folder and leave it's name as "New Folder", then I don't see an error. I'm also able to manipulate files however I want without seeing an error. Things I've Tried Changing permissions on the drive Reformatting the drive. I've tried using both a "Basic" and "Dynamic" partition table. Checking the drive for errors using Microsoft tools Things I've Not Yet Tried When I first installed Windows I was given a choice between three types of partitions to use. I no longer remember what the choices were or what I selected. One was a GUID partition table, one was a traditional MBR, and I can't remember the third option.

  Read the article

• BIOS interrupts, privilege levels and paging

  - by Jack

  Hi, I was learning about Intel 8086-80486 CPUs and their interactions with HW. But I still don´t understand it quite well. Please, help me fill blank spots. First, I know that CPU communicates with HW using BIOS interrupts. But, what really happens in PC, when I call some INT instruction? I know that according the interrupt table some instructions begin to execute, but how by executing some instructions can BIOS recognize what I want to do? Becouse as far as I know, CPU has no extra communication channel with BIOS, it can only adress memory and receive data. So how can I instruct BIOS to do something, when I can only address RAM? Next thing I don't understand is about privilege levels. I know about ring model, and access rights, but how does the CPU know which privilege level has executed an instruction? I think that these privileges apply only when intruction is trying to address memory, but how does an application get its privilege level? I mean I know its level 3, but how is it set? And last thing, I know that paging is address scheme that is used to support aplication-transparent virtual memory, or swapping, but I could not find any information about how paging is tied with protected mode. Like if paging is like next mode independent of protected mode, or its somehow implemented within protected mode. And if it is implemented in protected mode, isn´t it too slow, to first address application space, then offset, and then paging folder, page and offset once again?

  Read the article

• BIOS interrupts, priviledge levels and paging

  - by Jack

  Hi, I was learning about Intel 8086-80486 CPUs and their interactions with HW. But I still don´t understand it quite well. Please, help me fill blank spots. First, I know that CPU communicates with HW using BIOS interrupts. But, what really happens in PC, when I call some INT instruction? I know that according the interrupt table some instructions begin to execute, but how by executing some instructions can BIOS recognize what I want to do? Becouse as far as I know, CPU has no extra communication channel with BIOS, it can only adress memory and receive data. So how can I instruct BIOS to do something, when I can only adress RAM? Next thing I dont understand is about priviledge levels. I know about ring model, and acess rights, but how CPU knows which priviledge level has executed instruction? I think that these priviledges apply only when intruction is trying to adress memory, but how applications gets its priviledge level? I mean I know its level 3, but how its set? And last thing, I know that paging is adress scheme that is used to support aplication-transparent virtual memory, or swaping, but I could not find any informations about how is paging tied with protected mode. Like if paging is like next mode independent of protectet mode, or its somehow implemented within protected mode. And if it is implemented in protected mode, isn´t it too slow, to first adress application space, than offset, and than paging folder, page and offset once again? Thank you for every response.

  Read the article

• Cisco adaptive security appliance is dropping packets where SYN flag is not set

  - by Brett Ryan

  We have an apache instance sitting inside our DMZ which is configured to proxy requests to an internal NATed tomcat instance inside our network. It works fine, but then all of a sudden requests from apache to the tomcat instance stop getting through with the following in the apache logs: [error] (70007)The timeout specified has expired: ajp_ilink_receive() can't receive header Investigating into the Cisco log viewer reveals the following: Error Message %ASA-6-106015: Deny TCP (no connection) from IP_address/port to IP_address/port flags tcp_flags on interface interface_name. Explanation The adaptive security appliance discarded a TCP packet that has no associated connection in the adaptive security appliance connection table. The adaptive security appliance looks for a SYN flag in the packet, which indicates a request to establish a new connection. If the SYN flag is not set, and there is not an existing connection, the adaptive security appliance discards the packet. Recommended Action None required unless the adaptive security appliance receives a large volume of these invalid TCP packets. If this is the case, trace the packets to the source and determine the reason these packets were sent. All are machines are virtualised using VMware, and by default machines have been using the Intel E1000 emulated NIC. Our network administrator has changed this to a VMXNET3 driver in an attempt to correct the problem, we just have to wait and see if the problem persists as it's an intermittent problem. Is there something else that could be causing this problem? This isn't the first service where we have had similar issues. Our apache host is running Ubuntu 11.10 with a kernel version of 3.0.0-17-server. We have also had this issue on RHEL5 (5.8) running kernel 2.6.18-308.16.1.el5, this machine also has the E1000 NIC. NOTE: I am not a network administrator and am a software architect and analyst programmer responsible for these systems.

  Read the article

• BSOD Dump - EXCEPTION_DOUBLE_FAULT - ON Windows 2008 Server 64bit

  - by Mark K

  Hello, my windows 2008 server (datacenter ed) 64bit , have recently created a series of BSOD on a different applications. the error message is in general EXCEPTION_DOUBLE_FAULT. Can anyone please help with the analysis of the dump file bellow- Best regards, Mark 2: kd !analyze -v * Bugcheck Analysis * * UNEXPECTED_KERNEL_MODE_TRAP (7f) This means a trap occurred in kernel mode, and it's a trap of a kind that the kernel isn't allowed to have/catch (bound trap) or that is always instant death (double fault). The first number in the bugcheck params is the number of the trap (8 = double fault, etc) Consult an Intel x86 family manual to learn more about what these traps are. Here is a portion of those codes: If kv shows a taskGate use .tss on the part before the colon, then kv. Else if kv shows a trapframe use .trap on that value Else .trap on the appropriate frame will show where the trap was taken (on x86, this will be the ebp that goes with the procedure KiTrap) Endif kb will then show the corrected stack. Arguments: Arg1: 0000000000000008, EXCEPTION_DOUBLE_FAULT Arg2: 0000000080050033 Arg3: 00000000000006f8 Arg4: fffff800018b1678 Debugging Details: BUGCHECK_STR: 0x7f_8 CUSTOMER_CRASH_COUNT: 1 DEFAULT_BUCKET_ID: DRIVER_FAULT_SERVER_MINIDUMP PROCESS_NAME: CustomerService. CURRENT_IRQL: 1 EXCEPTION_RECORD: fffffa6004e45568 -- (.exr 0xfffffa6004e45568) ExceptionAddress: fffff800018a0150 (nt!RtlVirtualUnwind+0x0000000000000250) ExceptionCode: 10000004 ExceptionFlags: 00000000 NumberParameters: 2 Parameter[0]: 0000000000000000 Parameter[1]: 00000000000000d8 TRAP_FRAME: fffffa6004e45610 -- (.trap 0xfffffa6004e45610) NOTE: The trap frame does not contain all registers. Some register values may be zeroed or incorrect. rax=0000000000000050 rbx=0000000000000000 rcx=0000000000000004 rdx=00000000000000d8 rsi=0000000000000000 rdi=0000000000000000 rip=fffff800018a0150 rsp=fffffa6004e457a0 rbp=fffffa6004e459e0 r8=0000000000000006 r9=fffff8000181e000 r10=ffffffffffffff88 r11=fffff80001a1c000 r12=0000000000000000 r13=0000000000000000 r14=0000000000000000 r15=0000000000000000 iopl=0 nv up ei pl zr na po nc nt!RtlVirtualUnwind+0x250: fffff800018a0150 488b02 mov rax,qword ptr [rdx] ds:00000000000000d8=???????????????? Resetting default scope LAST_CONTROL_TRANSFER: from fffff800018781ee to fffff80001878450 STACK_TEXT: fffffa6001768a68 fffff800018781ee : 000000000000007f 0000000000000008 0000000080050033 00000000000006f8 : nt!KeBugCheckEx fffffa6001768a70 fffff80001876a38 : 0000000000000000 0000000000000000 0000000000000000 0000000000000000 : nt!KiBugCheckDispatch+0x6e fffffa6001768bb0 fffff800018b1678 : 0000000000000000 0000000000000000 0000000000000000 0000000000000000 : nt!KiDoubleFaultAbort+0xb8 fffffa6004e44e30 fffff800018782a9 : fffffa6004e45568 0000000000000001 fffffa6004e45610 000000000000023b : nt!KiDispatchException+0x34 fffffa6004e45430 fffff800018770a5 : 0000000000000000 0000000000000000 0000000000000000 0000000000000001 : nt!KiExceptionDispatch+0xa9 fffffa6004e45610 fffff800018a0150 : fffffa6004e46638 fffffa6004e46010 fffff80001965190 fffff8000181e000 : nt!KiPageFault+0x1e5 fffffa6004e457a0 fffff800018a3f78 : fffffa6000000001 0000000000000000 0000000000000000 ffffffffffffff88 : nt!RtlVirtualUnwind+0x250 fffffa6004e45810 fffff800018b1706 : fffffa6004e46638 fffffa6004e46010 fffffa6000000000 0000000000000000 : nt!RtlDispatchException+0x118 fffffa6004e45f00 0000000000000000 : 0000000000000000 0000000000000000 0000000000000000 0000000000000000 : nt!KiDispatchException+0xc2 STACK_COMMAND: kb FOLLOWUP_IP: nt!KiDoubleFaultAbort+b8 fffff800`01876a38 90 nop SYMBOL_STACK_INDEX: 2 SYMBOL_NAME: nt!KiDoubleFaultAbort+b8 FOLLOWUP_NAME: MachineOwner MODULE_NAME: nt IMAGE_NAME: ntkrnlmp.exe DEBUG_FLR_IMAGE_TIMESTAMP: 4a7801eb FAILURE_BUCKET_ID: X64_0x7f_8_nt!KiDoubleFaultAbort+b8 BUCKET_ID: X64_0x7f_8_nt!KiDoubleFaultAbort+b8 Followup: MachineOwner

  Read the article

• VMWare ESXi 4.1- 5.1 installation hang

  - by osij2is

  I'm well aware that I'm trying to install VMWare ESXi 5.1 on hardware that's not on the HCL. I can't find my motherboard on the ultimatewhitebox site as well. I acknowledge these issues in advance. What I'm trying to find is someway to access the logs during installation or see a console or log file to see where the installation is hanging at and remove a device or change a setting in the BIOS. The installation is hanging, not getting a purple screen of death. I thought by hitting ALT+F10 or F12 (or some key combination as such) would enable me to see the console but no such luck. I haven't been able to find much within the ESXi online documentation either. Here's the parts I'm using: AMD Phenom II x3 700 MSI 890FXA-GD70 (IOMMU capable) 16GB DDR3 1333 RAM (2x8GB DIMMs) Intel Pro 1000 (Dual-GbE) PCIe x4 (removed during installation) LSI 9211-8i PCIe (removed during installation) LSI 9201-16i PCIe (removed during installation) Matrox video card BIOS settings: IOMMU is enabled (during 5.1 IOMMU successfully loads) AHCI is enabled (hangs for 4.1) Both onboard Realtek NICs are disabled For ESXi 5.1, the installation hangs after vmkapi_v2_0_0_0 is loaded. For ESXi 5.0, it hangs when loading the vmklinux_9 module. For ESXi 4.1 U3, the installation hangs during loading of ahci module. Again, I'm looking for some way to view a console (service console?) or log file during or after an installation attempt to see what verbose error messages or logging can lead me to solving this problem.

  Read the article

• OpenSolaris / Nexenta problems with NetXen 4-port NIC card (ntxn driver)

  - by ewwhite

  Hello, I'm running NexentaStor Enterprise on an HP ProLiant DL180 G6 server. The onboard NIC interfaces surface as igb0 and igb1 and work well. However, I've added an HP NC375T 4-port network card using the NetXen 3031 chipset. This card should be handled by the ntxn driver in the SUNWntxn package, but that results in "ntxn0: failed to map doorbell" messages upon boot. The network interfaces don't show up. After some research, I found HP's driver package for the card. The release notes for the driver package state: This version of the Driver is supported only on Oracle Solaris 10 5/09 & 10/09. Oracle Solaris 10 5/09 & 10/09 contain an older version of NetXen P3 driver package called SUNWntxn. So, adding another version of NetXen P3 driver package using pkgadd command might result in conflicts with the NetXen driver binary & related files. Users are advised to uninstall native SUNWntxn driver package before installing the new package. The install completes, but I end up with a different set of errors in initializing the card. ifconfig ntxn0 plumb ifconfig: cannot open link "ntxn0": DLPI link does not exist dmesg output: Jan 29 07:20:17 ch-san2 ntxn: [ID 977263 kern.warning] WARNING: Memory not available Jan 29 07:20:17 ch-san2 ntxn: [ID 404858 kern.notice] NOTICE: ntxn0: Mac registration error Trying to manually create the device files: root@ch-san2:/volumes# add_drv -i "4040,100" ntxn ("ntxn") already in use as a driver or alias. Update the driver: root@ch-san2:/volumes# update_drv -f ntxn devfsadm: driver failed to attach: ntxn Warning: Driver (ntxn) successfully added to system but failed to attach Any ideas on how to get this driver working, or should I ditch the card and go with an Intel or something else?

  Read the article

• Why is usable RAM less than total RAM?

  - by D Connors

  My girlfriend bought a laptop last week. It's a core 2 duo with 4 GB We installed vista 64bit, and one of the first things we did was right click on "My computer" to see gthe properties. Immediately we noticed something strange about her RAM, the line said: Installed memory (RAM): 4,00 GB (3,68 GB usable) I told her not to worry, thinking it must be something about the laptop hardware (considering her vista installation came from the same DVD as mine, and I never noticed anything like that on my 4 GB desktop). One hour ago, it got worse. We looked at Properties again, and it now says: Installed memory (RAM): 4,00 GB (2,98 GB usable) What does that mean? Are those 1,02 GB missing or being used by the system? EDIT: There is a possibility that the sytem information is wrong. I just noticed that it reports an intel T6500 processor, when it's actually a T6400. How can I find out how much RAM is really available to the system? EDIT2: Checking the resource monitors, it says 1003 MB are reserved for the hardware. Is that good or bad? Thanks

  Read the article

• Error 0x80300001 Installing Windows Server 2008 R2 64bit on FastTrak TX4660 RAID volume

  - by Konstantin Boyandin

  I am trying to install Windows Server 2008 R2 Enterprise 64bit on the following hardware: motherboard Intel DBS1200BTL Promise FastTrak TX4660 RAID controller 4 disks set up in two RAID1 arrays (handled by FastTrak) I am trying to install Windows so it would boot from RAID1 volume created with the FastTrak controller. The installation goes as in the manual, I insert the disk with the driver, select 'Browse' and specify the correct driver, it finds all the RAID arrays but notifies me that error 0x80300001 happened, Windows can't be installed on the mentioned RAID volumes, since they may not be bootable (even though the target RAID volume is the first in boot options list). If I proceed with the installation, Windows copies and unpacks itself, performs other standard actions after that. After the computer is restarted, it won't boot (Windows Boot Manager appears in the boot devices list; however, neither it nor the RAID volume itself does not boot). Is it a known problem? I can attach the boot disks to the motherboard and use its RAID capabilities instead, but I'd prefer FastTrak ones. Driver version is 1.3.0.4. Thanks.

  Read the article

• Windows Server 2008 Stops Responding (Hyper-V Role Enabled)

  - by blackf0rk

  The machine is a brand new Dell Precision m6500, Core i5, 8GB RAM. Windows Server 2008 R2 (fully patched) with Hyper-V Role Enabled. Virtualization options in the BIOS are ON, SpeedStep is OFF, couldn't find C1E option in the BIOS to turn it off (I also got the impression that SpeedStep is C1E, but the Intel Product site lists them as separate "features." shrug) The server stops responding without any apparent reason. I've tried testing in multiple scenarios, all of which result in a crash at seemingly random times: With the Server sitting idle, no apps running. Server sitting idle with a Virtual Machine running. Using a BurnInTest application There's no blue screen. It doesn't restart. The screen just sits there. The keyboard backlight still responds and comes on with input, but nothing on the screen changes. There are no errors in the error log. I have to hold down the power button to turn it off. Doing memory tests on bootup results in no errors with the memory. I have a second identical system and the same thing happens there too. I've dual-booted into Windows 7 Profession x64 on this system with no problems. Further testing has shown that the issue is definitely related to Windows Server 2008 R2 and Hyper-V as it appears the crashing does not happen when the services are not running. I've installed all hotfixes relating to this issue (that I could find): 975530, 979444, 979491, 976427 System is still crashing without response.

  Read the article

• Internal drives vs USB-3 with external SSD or eSata with External SSD

  - by normstorm

  I have a need to carry VMWare Virtual Machines with me for work. These are very large files (each VM is 20GB or more) and I carry around about 40 to 50 VM's to simulate different software configurations for different client needs. Key: they won't fit on the internal hard drive of my current laptop. I currently execute the VM's from an external 7200RPM 2.5" USB-2 drive. I keep copies of the VM's on other 5400 external USB-2 drives. The VM's work from this drive, but they are slow, costing me much time and frustration. It can take upwards of 30 minutes just to make a copy of one of the VM's. They can take upwards of 10-15 minutes to fully launch and then they operate sluggishly. I am buying a new laptop (Core I7, 8GB RAM and other high-end specs). I intend to buy an SSD for the O/S volume (C:). This SSD will not be large enough to hold the VM's. I have always wanted a second internal hard drive to operate the VM's. To have two hard drives, though, I am finding that I will have to go to a 17" laptop which would be bulky/heavy. I am instead considering purchasing a 15" laptop with either an eSATA port or USB-3 ports and then purchasing two external drives. One of the drives might be an external SSD (maybe OCX brand) for operating the VM's and the other a 7400RPM 1TB hard drive for carrying around the VM's not currently in use. The question is which options would give me the biggest bang for the buck and the weight: 1) 2nd Internal SSD hard drive. This would mean buying a 17" laptop with two drive "bays". The first bay would hold an SSD drive for the C: drive. I would leave the first bay empty from the manufacture and then purchase/install an aftermarket SSD drive. This second SSD drive would have to be very large (256 GB), which would be expensive. I would still also need another external hard drive for carrying around the VM's not in use. 2) 2nd internal hard drive - 7400 RPM. Again, a 17" laptop would be required, but there are models available with on SSD drive for the C: drive and a second 7200 RPM hard drives. The second drive could probably be large enough to hold the VM's in use as well as those not in use. But would it be fast enough to drive the VM's? 3) USB-3 with External SSD. I could buy a 15" laptop with an SSD drive for the C: drive and a second hard drive for general files. I would operate the VM's from an external USB-3 SSD drive and have a third USB-3 external 7200 RPM drive for holding the VM's not in use. 4) eSATA with External SSD. Ditto, just eSATA instead of USB-3 5) USB-3 with External 7400 RPM drive. Ditto, but the drive running the VM's would be USB-3 attached 7400 RPM drives rather than SSD. 6) eSATA with External 7400 RPM drive. Dittor, but the drive running the VM's would be eSATA attached 7400 RPM drives rather than SSD. Any thoughts on this and any creative solutions?

  Read the article

• Slow VM on esxi 4.1

  - by user57432

  We have a FreeBSD 64bit running on a esxi 4.1, the hardware platform is a DELL R710 with 2 x 56xx (intel 6core cpu) and 48 GB ram. The FreeBSD vm is very slow, when we compiles/builds something on it, it takes 5 minuts and it says "build time 18 seconds.". There's no vmtools installed on the vm. The same vm is installaed on another R710 running esxi 4.0 for dell and there's no problems with that one. Does anyone have any idea about what to look for? the VMs on the second server (ESXi 4.1) is a clone of the VMs running on the first VMserver (ESXi 4.0 Dell edition). It's not possible for me to move the VM back to the first server since the file contaning the vm is too big. We installed the new esxi with a datasore with 8mb blocks because 1mb blocks dident allow for the file size we needed. It looks like the www server on the new ESXi 4.1 works fine, but I havent really tested it. There's not installed vmtools on any of the VMs (FreeBSD). The block size on the second VM (ESXi 4.1) datastorage is 8mb and 1mb on the first (ESXi 4.0)

  Read the article

• Debian and Multipath IO problem

  - by tearman

  Basically the situation is, I have a box running Debian, the box internally has an Intel SCSI RAID controller which is controlling 2 hard drives in RAID1 mode which is where the OS is installed. Further, I have a QLogic fiber channel adapter that connects the unit to a Fiber Channel SAN. My process of installation is I'll install Debian to the local drives, and leave the QLogic firmware out of it for the time being. Then once I get the unit online, I'll install the firmware drivers. This flops my internal drives from /dev/sda to /dev/sdc, which is a bit annoying, but recoverable. Probably should address these by UUID anyways. Once I get back online, I have to install multipath-tools (the framework is a multipath framework). However, once I reboot the machine again, it fails on boot after discovering multipath targets, saying my local drives are busy and cannot be mounted to /root. Any help in what may be the problem here? Or at least how to disable multipath until after the unit boots and then ignores the internal drives?

  Read the article

• ZFS + FreeBSD + virtualbox

  - by John

  Hi, I'm configuring a FreeBSD server hosting virtualbox serving half dozen mission critical busy mail servers. I just learned ZFS, I'm quite attracted, but have a few questions: what is the CPU overhead of ZFS? I googled and found little (or no) benchmark for that. from what I learned, when ZFS updates files, it keeps the old file as snapshot, and write the updated part for the new version. However that would mean for each snapshot it keeps that require significant storage overhead. How much is this storage overhead? For example, suppose I have 2TB usable space, how much space can actually be used for the latest version of files one year later? is FreeBSD with ZFS hosting virtualbox serving half dozen busy guest mission critical mail servers a reasonable combination? Anything particular to be careful with? And can I still choose ZFS for the guest OSs? This is because I may build another identical such box for redundancy, and will need to do some mirroring between each pair of the guest systems across the boxes. I'm trying to configure a Dell R710 for this. From what I learned, I shouldn't choose any RAID at all, is that true? In that case, are the drives still arrive hot swappable? this may sounds a bit pathetic, but since I have no experience with ZFS at all, and this is a mission critical server, so just ask just in case: I'm choosing twin Intel L5630 processors, and 6 x 600GB 15K RPM Serial-Attach SCSI drives. If I need more space in the future, I would just hot swap some drivers with larger capacity to expand the storage. There is no problem with these, right?

  Read the article

• Our application is responding different on client server

  - by WtFudgE

  I have an application running on our local server and it works perfect. However when I deploy my application to our client's server there are problems. If i copy all the sources to another local from their server, it works fine again.... I am talking about an ASP.NET application talking with windows server 2008. The server specs of our client are: intel Xeon 2.13 GHz 6 GB RAM 300 GB HDD windows server 2008 R2 Although I think it's not that important I will describe the problems I am talking about to give u a better idea: It is related to upating and deleting fields in the sql server. Whenever there is more than one user running the application, and updates or deletes (not even the same record!0, there seems to be fields updating/deleting wrongly. But as I said before, if we copy the source to another server it is not the case. So I assumed it is more configuration related. Do you guys have any idea what the issue could be? Thanks a lot EDIT: my client old me he disabled the sql related accounts Could this be related?

  Read the article

• Tomcat 6 Windows Server 64 Redirect Connector Fails

  - by Rafe

  So is there some problem with running the Tomcat connectors under a 64 bit windows OS? Here's my configuration: Windows Server 2003 64 bit Intel Xeon Tomcat 6.0.26 JVM 1.6.0 (64bit) ISAPI Redirect Connector 1.2.30.0 (64 bit) Calling the IP address of the site with :8080 brings up the tomcat page so I know that's running and the examples all work so its obviously not having a problem with the JVM. Calling the site ip on port 80 however gives me error 324 - looking at the application log on windows shows "Could not load all ISAPI filters for site/service. Therefore startup aborted". The ISAPI filter page under the web site properties shows the status of this filter to be down with a red arrow. The ISAPI filter name is jakarta and there is a corresponding virtual directory set up in the root of the site pointing to the same directory as the filter. The jakarta web service extension is also pointing to the required dll (c:\program files\apache software foundation\jakarta isapi redirector\bin\isapi_redirect.dll). Incidentally, this same problem occurs when trying to use Tomcat 5.5. I've also tried swapping out various redirect versions. It's really odd because I got it to work once with a version of the redirector that came with Plesk but I've since uninstalled everything to do with plesk and even trying to use the plesk-compiled dll doesn't work now. I am pulling my hair out on this, any ideas?

  Read the article

• raid 1 and high load average

  - by melocoton

  i have a server with high load average, I think the problem is the raid 1. cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdb1[1] sda1[0] 256896 blocks [2/2] [UU] md3 : active raid1 sdb3[1] sda3[0] 2562240 blocks [2/2] [UU] md4 : active raid1 sdb5[1] sda5[0] 958566272 blocks [2/2] [UU] md1 : active raid1 sdb2[1] sda2[0] 15366080 blocks [2/2] [UU] model name : Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz Linux 2.6.18-164.6.1.el5.centos.plus (local) 04/19/2010 avg-cpu: %user %nice %system %iowait %steal %idle 17.37 0.01 6.02 26.17 0.00 50.43 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 61.09 562.65 893.73 1557214 2473546 sda1 0.01 0.27 0.02 751 42 sda2 6.11 195.50 169.78 541075 469888 sda3 0.01 0.23 0.00 641 0 sda4 0.00 0.01 0.00 18 0 sda5 54.96 366.54 723.94 1014449 2003616 sdb 54.40 433.22 893.73 1199015 2473546 sdb1 0.01 0.16 0.02 436 42 sdb2 5.31 169.00 169.78 467729 469888 sdb3 0.01 0.31 0.00 865 0 sdb4 0.00 0.00 0.00 10 0 sdb5 49.05 263.65 723.94 729695 2003616 md1 29.96 364.39 166.68 1008498 461312 md4 124.15 630.07 713.28 1743822 1974112 md3 0.05 0.43 0.00 1192 0 md0 0.04 0.32 0.00 872 10 dm-0 7.96 83.29 23.02 230530 63720 dm-1 3.67 51.81 2.73 143394 7560 dm-2 7.63 67.76 27.35 187546 75696 dm-3 8.20 134.60 14.02 372514 38792 dm-4 5.90 10.66 39.35 29498 108912 dm-5 17.39 24.52 121.79 67850 337080 dm-6 27.19 229.60 139.89 635442 387168 dm-7 0.14 1.07 0.28 2970 776 dm-8 25.84 4.23 202.89 11698 561536 dm-9 14.77 8.38 112.35 23202 310960 dm-10 5.29 12.78 29.55 35376 81784 dm-11 0.16 1.25 0.05 3450 128 the server runs lvm in the md4

  Read the article

• process and memory issue on linux server

  - by zapping

  Need some assistance in analyzing apache and php process running on linux server. Its a 8-core intel processor with 4GB ram. When the website on it runs the top displays like this. PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 23459 username1 16 0 151m 27m 8388 S 11.3 0.7 0:11.71 php5 23730 username1 16 0 151m 28m 8388 S 11.3 0.7 0:03.87 php5 23458 username1 16 0 151m 28m 8388 S 3.0 0.7 0:19.20 php5 16202 mysql 15 0 459m 38m 4624 S 0.7 1.0 62:33.81 mysqld 24141 nobody 15 0 311m 5832 2304 S 0.3 0.1 0:00.03 httpd Why does the command say php5 when the website is accessed. Both apache and php was preconfigured so not sure whats done there. Tried setting up the same site and db on a different server but on it the process shows httpd always and not php5. The site uses mysql db. The problem is server load seems to go till about 5.x when the website was access by about 16users. When the free -m command was given the output shows total used free shared buffers cached Mem: 3941 3727 213 0 236 2734 -/+ buffers/cache: 756 3184 Swap: 4095 0 4095 Lots of memory seems to be in cache and free memory is less. Even when the website is not accessed that is leaving it very much idle for about 2days the free memory showed just 190. When the site is accessed the free memory seems to be go till 90mb then it increases to about 150mb. It always seems to remain just about 200mb. Is it somehow related to the server load showing 5.x. Will adding some more RAM resolve the load issue?

  Read the article

• Linux can't find file that exists

  - by Joe

  I'm trying to get Google's Dart language up and running, but it errors when running dart2js. I'm running Arch linux and I installed dart-sdk from AUR. Some relevant terminal output lies below. % dart2js main.dart /usr/local/bin/dart2js: line 7: /usr/local/bin/dart: No such file or directory % cat /usr/local/bin/dart2js #!/bin/sh # Copyright (c) 2012, the Dart project authors. Please see the AUTHORS file # for details. All rights reserved. Use of this source code is governed by a # BSD-style license that can be found in the LICENSE file. BIN_DIR=`dirname $0` exec $BIN_DIR/dart --allow_string_plus=false $BIN_DIR/../lib/dart2js/lib/compiler/implementation/dart2js.dart "$@" % file /usr/local/bin/dart /usr/local/bin/dart: ELF 32-bit LSB executable, Intel 80386, version 1 (SYSV), dynamically linked (uses shared libs), for GNU/Linux 2.6.15, BuildID[sha1]=0x27fe166ca015c1adfeaf3a6f9c018e7d7af46d9f, stripped % ls -alh /usr/local/bin total 4.9M drwxr-xr-x 2 root root 4.0K Jun 10 22:51 . drwxr-xr-x 12 root root 4.0K Jun 10 22:51 .. -rwxr-xr-x 1 root root 422K May 10 22:41 cargo -rwxr-xr-x 1 root root 2.7M Jun 10 22:50 dart -rwxr-xr-x 1 root root 360 Jun 6 16:20 dart2js -rwxr-xr-x 1 root root 176 Jun 6 16:20 pub -rwxr-xr-x 1 root root 166K May 10 22:41 rustc -rwxr-xr-x 1 root root 1.6M May 10 22:41 rustdoc % uname -rm 3.3.7-1-ARCH x86_64 Could it be because I'm running a 64bit OS and the dart binary is 32bit?

  Read the article

• Can VMWare Server 2.0 be useful in Production for easing backups?

  - by Keith Sirmons

  Howdy, Let's run this idea by the group here. I am thinking about using VMWare Server in production to host a 2008 Domain Controller with DHCP and DNS, a 2008 member server with WSUS, some virus software, and other "management" utilities a second 2008 member server with SQL, IIS, and File Shares for a medium business of 50-100 desktops. The reason I am leaning toward Server vs ESXi is for backup purposes. Using ESXi, if I want to backup the VM's, I would need a second server in the office with enough storage availability to hold a copy of the vmdks. I am wondering if putting this virtual environment on top of a basic 2008 server install will allow for easier backups to both tape and/or to offsite storage using JungleDisk. Can a snapshot be triggered easily via a scheduled job? I know this doesn't necessarily handle file level restores, but I want to make sure in a DR situation, we can restore production servers quickly. Does this concept hold water? Would a very minimum install of the 2008 Host remove too many resources from the actual production machines? This would be a new Dell 410 server with 12 GB ram and (6) 600 GB 15K in a RAID 6, Dual Intel Xeon 2.26GHz procs.

  Read the article

< Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >