Search Results

Search found 25894 results on 1036 pages for 'ask the readers'.

Page 343/1036 | < Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• Can I upgrade Lucid to Precise with the 12.04.1 desktop image?

  - by rahmad ars

  I am running Ubuntu Lucid and would like to upgrade to Precise, using the normal ubuntu-12.04.1-desktop-...iso image. So far I have tried upgrading with the CD but was not given the choice. Searching on the internet, I have found upgrading using the ubuntu-12.04.1-alternate-...iso image works, but I don't have great internet access. Is upgrading from Lucid possible, with the ubuntu-12.04.1-desktop image?

  Read the article

• How do I customize the Unity launcher for different workspaces?

  - by Srijan

  How do I customize the Unity launcher for different workspaces for Ubuntu 12.04? I am using x86-64 bit architecture running solely Ubuntu 12.04. I have searched in the community for possible aspects of this question as per the link Different Launchers for Different Workspaces? but the links provided in this doesn't address my issue as the links are outdated and it does not exactly say how to customize the launcher. Besides the environment is now buzzing with unity 5.4 and also Ubuntu 12.10. So can someone please help me to customize the unity launcher for Ubuntu 12.04 for different workspaces? Thanks a zillion in advance. Is there any features enabling customization of launcher in different workspaces in unity 5.4?

  Read the article

• 12.04 LTS boot hangs at "SP5100 TCO timer: mmio address 0xfec000f0 already in use", didn't yesterday

  - by DarkIron112

  Dual-booting Windows 7 and Ubuntu 12.04 LTS. I went to reboot from Win to Ubu, and found a few interesting things. My POST screen is covered in blocks of epileptic colors until I hit GRUB, which continues when I try to boot into Ubuntu. These color blocks don't appear when I use my on-board VGA, so I'll just attribute to that. Grub dimensions are swapped (card vs onboard, probably), but, when interfacing with onboard VGA, the Grub Timeout Counter works and when using my card, it does not (see "[!!!]" below for more information) Booting into Ubuntu directly causes the error: SP5100 TCO timer: mmio address 0xfec000f0 already in use Booting into recovery mode, meanwhile, and then "resuming normal boot" gets me to the desktop without native 1440x900 resolution and graphic drivers can't tell the monitor it's looking at (I assume this is because it's not a full graphic boot, and as it says, some drivers won't run?) [!!!] When I reboot after going into recovery mode, the countdown timer works ONCE, puts me back into default ubuntu boot, and then does not work again until after another recovery-mode boot. Windows 7 can boot perfectly with no issues whatsoever from epilepsy color blocks or driver detection. This makes me wonder /why/ the POST screen can't handle my video card anymore. Amidst all the diagnostics, I opened my case and re-seated the videocard securely, ensuring it wasn't a loose connection-- But this did nothing to help me. Hardware I am running an NVidia GeForce GTX 8800 video card in a PCI slot. I have 4.8GiB memory, an AMD Athlon II Quad-core 640 Processor, on an MSI K9N6GM Series Mobo. Onboard video is an NVidia GeForce MCP61(V/S/P) card. Note: I did not have any of these problems yesterday, and I have been using Ubuntu intensively for a week, though it's been working flawlessly for months. I've recently been using it to mod my Android phone, perhaps I messed something up in the file system?

  Read the article

• How to mount ext4 partition?

  - by Flint

  How do I mount an ext4 partition as my user account so I wouldn't require root access to r/w on it? I used -o uid=flint,gid=flint on the mount command but I keep getting mount: wrong fs type, bad option, bad superblock on /dev/sda7, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Another thing, I want avoid using udisks for now as it doesn't let me mount to my specified mount point name.

  Read the article

• Creating widgets using GtkBuilder

  - by user72943

  I am using Glade to design a Box with widgets and then load these widgets into my UI at run-time. To create each Box with widgets at run-time, I create a new GtkBuilder, call add_from_string passing in the text from the .ui file Glade creates, and then use the object returned from get_object("box1") in the UI. I know I could create the widgets with code, but for now, I'd like to use the .ui files Glade creates. It seems inefficient though to instantiate a new GtkBuilder object and the wasted Window object for every Box I want to create. Is there a more efficient method to load .ui files without creating a new GtkWidget object and wasted Window object? Thanks, Vance

  Read the article

• How do I get a Canon MP550 working with Gutenprint?

  - by Marek

  My printer canonMP550 doesn't work with i7 x86 64bit under Ubuntu 11.10 with cups+Gutenprint2.5.7. What I found, is: in gutenprint it is translated into ip4000 only, but it belongs to the group ip4700, which is translated into ip4300 (parameter). I tried to correct, read only, what to do? Next is gutenprint uses cups 1.2, but installed is cups 1.5 , so instead system/library/ color sync/ ..... it is usr/share/color/icc/sRGB.icc. So this seem to be real bugs, but Ii am new and need help to correct this staff!

  Read the article

• ejabberd starts slow and fails

  - by Michael Tanner

  I installed ejabberd and tried to set it up. On my server there are strict rules which allow only several services and denies everything else. I experienced starting problems with my iptables rules and found out that ejabberd works when I allow everything in the iptables and restore my rules afterwards. Then it also works for connecting, registering and else. What could be the problem in my rules? Attached here: http://fixee.org/paste/s5s744j/ Would be nice to get a correction straight on fixee if I made a mistake. Thanks in advance. Edit 1: In the log files there are no specific error messages during startup.

  Read the article

• Can't convert .iso to .img on iMac G5

  - by user89004

  So I'm trying to create a bootable USB stick in order to install Ubuntu 12.04.1 on my iMac G5 running Mac OS X 10.4.11 but whenever I try to convert the downloaded .iso file into a .img, the .img.dmg file that the terminal creates just suddenly dissapears no matter where I select the output file to be. I tried hdiutil convert -format UDRW -o /path/to/target.img /path/to/ubuntu.iso and also hdiutil convert /path/to/ubuntu.iso -format UDRW -o /path/to/target.img but the exact same thing happens. I tried becoming root before I do all of this with sudo su but I still get the same results. The totally weird thing is that it works perfectly with Ubuntu Minimal .iso files. Could it be that the .iso I downloaded is corrupt?

  Read the article

• Why does Ubuntu, sometimes, fails to load?

  - by mohit

  I recently installed Ubuntu 12.04 LTS on my SONY VAIO VPCEH (with Windows 7 Home Basic previously installed). Sometimes when I boot in Ubuntu, following things happen: Ubuntu loading screen seems to freeze. Esc key doesn't show installation progress. Hard-drive led doesn't glow. caps lock and scroll lock keys keep blinking. I've to manually restart my laptop. On restart, Ubuntu loads normally. What can I do to recover from present situation?

  Read the article

• SMART: DISK FAILURE IS IMMINENT (under 24 hours?)

  - by flix

  I have on my hard drive 2 OSes: Ubuntu 12.04 and Windows Vista( I keep it just because of school). Everything was OK on both OSes,but one day on Ubuntu I was getting awkward noises from my notebooks's hard drive and then everything stops and I couldn't do anything. On Windows everything was ok. Everytime I boot on Ubuntu I can get 5 minutes of normal run, without problems. After that the hard drive sounds crazy and nothing works. I could run S.M.A.R.T tests from a older Ubuntu CD (10.04) from the GUI(Disk Utility, or something like that and from terminal). From the GUI I got that the DISK FAILURE IS IMMINENT and I have ~700 bad blocks(or broken blocks, I had that test I while ago) on my HDD. From the terminal ( I don't remember if it was fsck or a SMART test command) I got that the HDD will fail in under 24 hours. Since then it passed 2-3 weeks. I've tried "badblocks" but after 10 hours it was still running and I had to stop it. Now I have to use cygwin and other alternatives for my linux apps on Windows. PLEASE HELP!!! How can I separate the bad blocks from Ubuntu so it wouldn't use them?

  Read the article

• toshiba c800 Fn keys not working

  - by Nirjon Nj

  i am a new born baby in Ubuntu family. And i am really loving it. but i am having few issues which are rally annoying.Please help me to remain in this family. my Toshiba C800 laptop(12.04lts desktop) has special Fn keys as followed Fn+ F2-BRIGHTNESS DOWN F3-BRIGHTNESS UP F4-DISPLAY SELECT F5-TOUCH PAD on/off F6-PREVIOUS F7-PLAY/PAUSE F8-NEXT F9-VOLUME DOWN F10-VOLUME F11-MUTE F12-WiFi on/off now the problem is keys are working fine from F6 to F11(media player keys, i may say) but the keys from F2 to F5 and F12(setting change keys) are not working. please help me. i really liked ubuntu!!

  Read the article

• Recovering data from /

  - by Abhijit Gavas

  I accidentally installed Ubuntu to one of my data drives from Windows. The drive was a NTFS drive and contained about 80 GB of important data. The size of the drive is 110 GB. Its new file system is ext4. In an attempt to recover the data, I downloaded foremost and tried the following commands: foremost -i / -o /media/281C8DB01C8D7998/Recovery/ -T -v foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v (sda7 is the drive in question.) It appears that with either command, foremost gets stuck reading some file. Here is the console output: abhi@abi-PC:/dev$ foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Foremost version 1.5.7 by Jesse Kornblum, Kris Kendall, and Nick Mikus Audit File Foremost started at Fri Sep 28 20:58:00 2012 Invocation: foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Output directory: /media/281C8DB01C8D7998/Recovery_Fri_Sep_28_20_58_00_2012 Configuration file: /etc/foremost.conf Processing: stdin |------------------------------------------------------------------ File: stdin Start: Fri Sep 28 20:58:00 2012 Length: Unknown Num Name (bs=512) Size File Offset Comment Killed As you can see I have to kill it from system monitor. This approach does not seem to be working. What else could I try to recover the files? Please help. The files are very important and I will be devastated if I cannot recover them.

  Read the article

• Burned DVD essentially has no content and the DVD is not bootable when creating on Mac OSX

  - by Tom Winans

  I have been unsuccessful when burning downloaded ISOs to a DVD on OSX - the burned DVD essentially has no content and the DVD is not bootable. I've tried Ubuntu versions of 11.x and 12.04 with no success. Further, I took the DVD out of an Ubuntu Unleashed book (v11.x), and am unable on several OSX laptops to read the DVD. The applications to manage ISO disks on OSX are really straightforward, and they properly function with ISOs of other linux distributions. Is there a problem with Ubuntu's? Or is it just me?

  Read the article

• Ubuntu 12.10 upgrade is stalled

  - by Wuchtbrumme123

  My Ubuntu is upgrading to 12.10 at the moment but since 4 hours or more I see only previous packages get restored and nothing happen. If I exit the upgrading now is all my previous data lost or does the Computer boot my old Ubuntu? I had a problem that is similar to this before while installing Linux on my fathers notebook. After the installation got crashed the Computer wasn't able to boot and I wasn't able to reinstall it. I need help I don't know what to do now.

  Read the article

• Empathy not showing in memenu

  - by dadexix86

  I just installed 12.10 and noticed that, even if I added more than one account to Online Accounts and I'm actually using empathy to chat, it is not present in Messaging Menu or in any other point of the tray. This means that if i close it, it remains open but unaccessbile and I have to start it again from dash. How can i integrate it in messaging menu (shouldn't this be the default?) or, at least, make it showing me a tray icon?

  Read the article

• Lubuntu 12.04 on Acer laptop boots to blank blue screen

  - by WGCman

  My previous question on this was closed, but I am posting it again as the solution which my son eventually found may assist other users of the forum, or someone may be able to tweak the solution to improve the performance. Having installed Kubuntu 12.04.01 from a live USB onto my desktop, I wanted to do the same on my laptop, an Acer Aspire 1362 Laptop, which has 256MB RAM (actually 512 "on the box", but a good deal can be borrowed by the graphics!). I found Kubuntu wouldn't run on so little memory but downloaded: Lubuntu-12.04-alternate-i386.iso, which I understood was light enough to go. The laptop has one internal 40GB Toshiba hard drive divided into 3 partitions: C,19GB with Windows XP, Windows program files and some data, D, 19GB mostly data, and a small 2GB partition with some Acer software, which XP can't normally “see”. I transferred most of the contents of D to a memory stick, leaving 16GB free for Lubuntu. I did not want to dump XP yet, though it is painfully slow. I installed Lubuntu from then USB stick, accepting the default answers to most of the questions. The D: partition was further partitioned into a 500MB boot partition, 10GB for Linux, 2GB Swap and 6GB for data shareable between Linux and Windows. I had no error messages during installation, rebooted, was offered the choice of Ubuntu or XP, and selected the former. After a few minutes, I get a dark blue screen announcing Lubuntu with five dots underneath which lighten in turn. Eventually the lights stopped, and whatever I try the screen remains blank apart from “Lubuntu” I tried several solutions suggested on the forum for “identical” questions but without success.

  Read the article

• Printing with Lacie Lightscribe requires root privileges

  - by James

  I have installed Lacie Lightscribe software on Ubuntu 12.04. Everything seems to be fine, the drive is detected, the proper media is detected, but when I click print I get the message "Printing Requires Root Privileges". I am the main (administrator) account on this computer, part of the sudo group and I cannot seem to find an answer to this dilemna in plain english. I've seen some apparently relevant posts which say things like "check whether the files /usr/4L/4L-gui and /usr/4L/4L-cli have any setuid-bits set. If so, remove them" but I need more detailed step-by-step instructions than that, please. Is there anyone who knows how to solve this?

  Read the article

• Best place to install apps

  - by t3ch

  I am completely new to Ubuntu and I must say AskUbuntu and you folks are of great help. So now when I have started installing and playing with apps, my question is what is the best place to install/download apps? Like in Windows it usually goes under your C: drive and then you manage it under Program Files. Linux structure is quite different with a different folder hierarchy. I have attached the directory structure of my machine as well. I thought this question would help lot of beginners.

  Read the article

• Internal Mic not working on Dell Adamo 13

  - by AFD

  So I'm using Elementary Luna Beta (based on Ubuntu 12.04 LTS) on a spare HDD after successfully using Jupiter release (based on 10.10) for many years. In Jupiter I had my internal mic work out of the box and with Skype installed from deb it was all setup without having to step foot inside the terminal. In Luna Beta the internal mic is not recognised by the OS and so also not recognised by Skype. I believe the hardware is this (from sudo lshw): *-multimedia description: Audio device product: 82801I (ICH9 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 03 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:46 memory:f8600000-f8603fff As well as this I ran cat /proc/asound/card0/codec* | grep Codec which gave me: Codec: IDT 92HD73C1X5 Codec: Intel Cantiga HDMI How do I tweak Luna to get this hardware working properly? I'm able to switch out my Luna HDD with the Jupiter HDD to help troubleshoot what the differences are between the two and why the more recent OS can't find / use the mic correctly. Thanks in advance for any help you can give.

  Read the article

• apt-get install does not work. Gives the same error every time E: Unable to locate package

  - by SAMEER

  There is an issue, for every package that I try to install. I am using VMWare Player 3.16 & I have installed Ubuntu 12.04. The error is: E:Unable to locate package (PACKAGE NAME) Also, another problem is that there are some configuration errors. So I have to use the CLI rather than the GUI. Now if this is a network error, I'm not sure as to how to open the setting from the command prompt. Even if I get to the GUI, it might not work, as the shortcuts are not available.

  Read the article

• How to control / disable low level battery on bluetooth mouse

  - by Alberto

  I have a little problem with my Kesington Bluetooth Mouse on Ubuntu 12.10. Ubuntu 12.10 considers my bluetooth mouse battery as a system battery as if it was the main laptop battery (so I have two on the battery indicator, the main and the bluetooth one). When it runs low level, near to die, battery, my laptop acts as if it was the main battery and I must quickly stop bluetooth and continue on the touchpad if I want to work. Can anyone help me? Maybe I prefer to disable the battery control over the mouse, I don't care about it, I know it is fully charged, but Ubuntu always starts on 33% or less, I just want to work with it and when it will be battery-off I will recharge the batteries. Many thanks in advance. Alberto.

  Read the article

• How do I use a 4GB USB flash drive to install Ubuntu 12.10?

  - by Logan

  I've downloaded "ubuntu-12.10-desktop-amd64" and used Pen Drive Linux to get it onto my USB. I then restarted my computer (a Windows 7 Home Premium edition) and entered the boot menu to have it boot from the Sandisk USB (it called it Sandisk Cruzer Cruzer). Linux came up and asked if I wanted to try or install. I picked install, connected to my Wi-Fi, and installed it. After my laptop restarted, Windows booted immediately. I have tried several times and cannot get a choice between the two. P.S. I have used the Windows Installer, Wubi, but at the last second it gave me some kind of error.

  Read the article

• Ubuntu 13.04 client cannot connect to Raspbian samba share

  - by envoyweb

  I have a client Ubuntu 13.04 machine trying to connect to a server running Raspbian with samba and samba-common-bin installed on the server I can see my share and when I try to login I get this error: Unable to access location: Failed to write windows share Cannot allocate memory. I have installed ntfs-3g for the usb hard drive that already auto mounts on the server so I never had to create a directory or edit fstab. Testparm on the server states the following: [global] workgroup = ENVOYWEB server string = %h server map to guest = Bad User obey pam restrictions = Yes pam password change = Yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%m max log size = 1000 dns proxy = No usershare allow guests = Yes panic action = /usr/share/samba/panic-action %d idmap config * : backend = tdb [homes] comment = Home Directories valid users = %S create mask = 0700 directory mask = 0700 browseable = No [printers] comment = All Printers path = /var/spool/samba create mask = 0700 printable = Yes print ok = Yes browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/printers [BigDude] comment = Sharing BigDude's Files path = /media/BigDude/ valid users = @users read only = No create mask = 0755 testparm on the client which is running ubuntu is as follows [global] workgroup = ENVOYWEB server string = %h server (Samba, Ubuntu) map to guest = Bad User obey pam restrictions = Yes pam password change = Yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%m max log size = 1000 dns proxy = No usershare allow guests = Yes panic action = /usr/share/samba/panic-action %d idmap config * : backend = tdb [printers] comment = All Printers path = /var/spool/samba create mask = 0700 printable = Yes print ok = Yes browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/printers

  Read the article

• TuxOnIce-problem: "CPU stuck for 22 s"

  - by Lester

  I use Ubuntu 12.04 LTS on a Lenovo Thinkpad T61 and am new to Linux. I installed TuxOnIce following this Guide. Actually it works but resuming takes very long. Shortly before resuming is complete I see some message flashing in command-line like "CPU stuck for 22 s". Some googling brought up pages like this but it did not help me solve me problem. I suppose being absolutely new to Linux is the biggest part of the problem.

  Read the article

< Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >