Search Results

Search found 22871 results on 915 pages for 'automated install'.

Page 343/915 | < Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >

  • Mount encrypted hfs in ubuntu

    - by pagid
    I try to mount an encrypted hfs+ partition in ubuntu. An older post described quite good how to do it, but lacks the information how to use encrypted partitions. What I found so far is: # install required packages sudo apt-get install hfsprogs hfsutils hfsplus loop-aes-utils # try to mount it mount -t hfsplus -o encryption=aes-256 /dev/xyz /mount/xyz But once I run this I get the following error: Error: Password must be at least 20 characters. So I tried to type it in twice, but that results in this: ioctl: LOOP_SET_STATUS: Invalid argument, requested cipher or key (256 bits) not supported by kernel Any suggestions? Thx Edit: One thing I'm not sure about is whether I use the right password. My assumption is that it is my default one for these situations. But I'm not sure whether Max OSX choose another password (internally) for that.

    Read the article

  • Ubuntu 12.04 installation on GPT + RAID going into grub rescue

    - by Proy
    I have two 2TB disks. I am installing Ubuntu 12.04 using the alternate version of the server cd. On the partitioning page I have done my partitioning as follows /dev/sda1 - 32 MB - bios_grub /dev/sda2 - 50 GB -raid device /dev/sda3 - 8 GB -raid device /dev/sda4 - Balance full GB - raid device /dev/sdb1 - 32 MB - bios_grub /dev/sdb2 - 50 GB -raid device /dev/sdb3 - 8 GB -raid device /dev/sdb4 - Balance full GB - raid device After this I have setup raid devices /dev/md0 for /(/dev/sda2 + /dev/sdb2) for / ext4 /dev/md1 for swap( /dev/sda3 + /dev/sdb3)for swap /dev/md2 for /home(/dev/sda4 + /dev/sdb4)for /home ext4 The installation finishes it shows that it is installing grub to /dev/sda and /dev/sdb. But once the system reboots it falls into grub rescue mode. on doing ls I can not see the md devices only hd once. I also tried booting into rescue mode with the install cd and doing grub-install /dev/sda and /dev/sdb. What am I doing wrong ? Why is grub2 not detecting the raid revices ? UPDATE: I just did the same steps with Ubuntu 10.04 and it worked perfectly fine. I wiped out the RAID and partitions and everything and did it from scratch. I think the issue is with Ubuntu 12.04 and the way it partitions 2 TB disks

    Read the article

  • What are the downsides of leaving automation tags in production code?

    - by joshin4colours
    I've been setting up debug tags for automated testing of a GWT-based web application. This involves turning on custom debug id tags/attributes for elements in the source of the app. It's a non-trivial task, particularly for larger, more complex web applications. Recently there's been some discussion of whether enabling such debug ids is a good idea to do across the board. Currently the debug ids are only turned on in development and testing servers, not in production. There have been points raised that enabling debug ids does cause performance to take a hit, and that debug ids in production may lead to security issues. What are benefits of doing this? Are there any significant risks for turning on debug tags in production code?

    Read the article

  • Create access point (uap0) on debian 7(arm) - not found?

    - by ethrbunny
    I'm working with a fanless PC that has an ARM chipset, 2 eth plugs and a wifi card (among other things). If I install debian 6 on it all three network interfaces are available at boot time. Today I tried to install debian 7 and had numerous errors indicating that the wireless card isn't supported. uap0: error fetching interface information: Device not found SIOCSIFADDR: No such device uap0: ERROR while getting interface flags: No such device uap0: ERROR while getting interface flags: No such device No such device ERR:UAPHOSTCMD is not supported by uap0 ERR:Command sending failed! No such device ERR:UAPHOSTCMD is not supported by uap0 ERR:Command sending failed! I've tried comparing the kernel module list to the working system but there are too many other differences to make something obvious enough (to me) stand out. How would I get started debugging this problem?

    Read the article

  • Broadcom bluetooth driver for Windows 7 on MacBook Pro

    - by Sergiy Byelozyorov
    I have installed Windows 7 on MacBook Pro using BootCamp. Usually when turning my Bluetooth headset on and trying to pair it with Mac for the first time, Windows would fail to install drivers and open solution in Action Center, which suggests to download the driver from the Broadcom webpage. This worked before and drivers would install and work. However now, when I start driver installer, it would get stuck at "Detecting Bluetooth Device" stage. Below the steps there is also a warning with text, which says "Please plug in or turn ob your Bluetooth device". This is how the installer looks like when it's stuck: I have tried turning my headset on/off, bringing it into pairing mode, installing/uninstalling device to/from the Bluetooth Devices. None of these worked. Any ideas?

    Read the article

  • Creating a bootable flash without overlayfs

    - by Septagram
    I want to create an USB stick to carry my Ubuntu everywhere around with me. It's not intended to spread Ubuntu by installing it everywhere, but rather for running my configured system on any computer I come across. So far, I went with installing Ubuntu with unetbootin, however, I have some issues with this. When installed with netbootin, the original disk image is kept intact on the flash drive, forever. Also, a file is created for persistent storage and during boot it is accessed together with the image by overlayfs. This, in my opinion, has the following problems: If system is updated regularly, then files from the image are overwritten in persistent storage, doubling their size and wasting precious space. Persistent storage has a fixed size that you have to define from the start, again, wasting precious space. I'm not 100% sure, but maybe using overlayfs makes disk access slower, and more so on the relatively slow devices. So I'd like to find another solution: either to get rid of the original image or to install Ubuntu "normally" on the separate ext2 partition, or maybe even install it in the main vfat partition on the USB stick. Suggestions?

    Read the article

  • Windows 7, Drivers, Cloning and Sysprep

    - by Frank Thornton
    I have Windows 7 working on one machine but when I move it off to the new machine it crashes. If this is a driver issue do I need to download the drivers and install them first? Or do I install Windows 7 on the new machine first then copy the drivers folder over to the other disk so it will boot up correctly? EDIT: I was trying this as well: http://www.todo-backup.com/support/tutorial/redeploy-system-to-dissimilar-hardware.htm EDIT: I tried sysprep but on bootup I see the Windows logo then the system crashes. I can stick the drive back in the old hardware and it runs fine.

    Read the article

  • MySQL - Configuration

    - by Stuart Brierley
    Having previously detailed how to install MySQL Server, the next step is configuring MySQL. The MySQL configuration wizard can either be run immediately following installation from the MySQL installation wizard or manually from the Start Menu. Following the splash screen you can then choose whether to run a detailed or standard configuration. The detailed configuration allows you to create the optimal configuration for your specific machine, whereas the standard configuration creates a general configuration that can then be manually tuned. I chose detailed.   You are then asked to choose the type of server instance that is being configured. In this case it is a developer machine. Following this you are asked to choose the type of database usage that you expect on the server. I opted for multifunctional. You must then specify the location of the InnoDB tablespace.   Next specify the number of concurent connections to the server.   Now you must configure the networking options. I left the Strict mode enabled as this is the recommended option, but I disabled TCP/IP networking as I wanted to restrict this MySQL installation to the local machine only.   Set the character set that is best suited to your use - for me this was the default standard character set. Next up is the option to run MySQL as a service and whether or not to include the mysql dircetories in the windows PATH. I kept the install as a windows service option enabled, but unchecked the Launch MySQL server automatically option. This is because I only wanted MySQL running when I specifically want to use it. I also enabled the include in windows PATH option.   You can then change the security settings for the mysql installation. I opted to change the root password, disable root from local machines and disable annoymous access.   You are now ready to execute the configuration.   Once completed you should hopefully see the completed screen with lots of nice ticks against the various configuration tasks.

    Read the article

  • Writing selenium tests, should I just get it done or get it right?

    - by Peter Smith
    I'm attempting to drive my user interface (heavy on javascript) through selenium. I've already tested the rest of my ajax interaction with selenium successfully. However, this one particular method seems to be eluding me because I can't seem to fake the correct click event. I could solve this problem by simply waiting in the test for the user to click a point and then continuing with the test but this seems like a cop out. But I'm really running out of time on my deadline to have this done and working. Should I just get this done and move on or should I spend the extra (unknown) amount of time to fix this problem and be able to have my selenium tests 100% automated?

    Read the article

  • Moving a Drupal between linux servers, best practice to avoid file-ownership problems

    - by zero
    I want to port over a Drupal commons 6x24 from a local LAMP-stack to a production webserver. Both systems run OpenSuse Linux. How do I do this, what are the most important steps. How should I handle file-ownership. It's important for me to have to have full control of the file ownership. If I use the wwwrun account, I frequently run into problems, due to a very strict webserver-admin. See for example the long history of looking for fixes and solutions see this thread and even more interesting see this very long and impressive thread here. All troubles I run into have to do with file-owernship and permissions. This is my current setup; Note: This was just a quick hacked installation - quick and dirty. Well my interest is after the general options i have in the port of a drupal from linux to linux linux-vi17:/srv/www/htdocs/com624 # ls -l insgesamt 224 -rwxrwxrwx 1 root www 45285 19. Jan 00:54 CHANGELOG.txt -rwxrwxrwx 1 root www 925 19. Jan 00:54 COPYRIGHT.txt -rwxrwxrwx 1 root www 206 19. Jan 00:54 cron.php drwxrwxrwx 2 root www 4096 19. Jan 00:54 includes -rwxrwxrwx 1 root www 923 19. Jan 00:54 index.php -rwxrwxrwx 1 root www 1244 19. Jan 00:54 INSTALL.mysql.txt -rwxrwxrwx 1 root www 1011 19. Jan 00:54 INSTALL.pgsql.txt -rwxrwxrwx 1 root www 47073 19. Jan 00:54 install.php -rwxrwxrwx 1 root www 15572 19. Jan 00:54 INSTALL.txt -rwxrwxrwx 1 root www 14940 19. Jan 00:54 LICENSE.txt -rwxrwxrwx 1 root www 1858 19. Jan 00:54 MAINTAINERS.txt drwxrwxrwx 3 root www 4096 19. Jan 00:54 misc drwxrwxrwx 35 root www 4096 19. Jan 00:54 modules drwxrwxrwx 4 root www 4096 19. Jan 00:54 profiles -rwxrwxrwx 1 root www 1470 19. Jan 00:54 robots.txt drwxrwxrwx 2 root www 4096 19. Jan 00:54 scripts drwxrwxrwx 4 root www 4096 19. Jan 00:54 sites drwxrwxrwx 7 root www 4096 19. Jan 00:54 themes -rwxrwxrwx 1 root www 26250 19. Jan 00:54 update.php -rwxrwxrwx 1 root www 4864 19. Jan 00:54 UPGRADE.txt -rwxrwxrwx 1 root www 294 19. Jan 00:54 xmlrpc.php linux-vi17:/srv/www/htdocs/com624 # thx to BetaRides answer here a quick overview on the drush functionality with rsync http://drush.ws/ core-rsync Rsync the Drupal tree to/from another server using ssh. Examples: drush rsync @dev @stage Rsync Drupal root from dev to stage (one of which must be local). drush rsync ./ @stage:%files/img Rsync all files in the current directory to the 'img' directory in the file storage folder on stage. Arguments: source May be rsync path or site alias. See rsync documentation and example.aliases.drushrc.php. destination May be rsync path or site alias. See rsync documentation and example.aliases.drushrc.php. Options: --mode The unary flags to pass to rsync; --mode=rultz implies rsync -rultz. Default is -az. --RSYNC-FLAG Most rsync flags passed to drush sync will be passed on to rsync. See rsync documentation. --exclude-conf Excludes settings.php from being rsynced. Default. --include-conf Allow settings.php to be rsynced --exclude-files Exclude the files directory. --exclude-sites Exclude all directories in "sites/" except for "sites/all". --exclude-other-sites Exclude all directories in "sites/" except for "sites/all" and the site directory for the site being synced. Note: if the site directory is different between the source and destination, use --exclude-sites followed by "drush rsync @from:%site @to:%site" --exclude-paths List of paths to exclude, seperated by : (Unix-based systems) or ; (Windows). --include-paths List of paths to include, seperated by : (Unix-based systems) or ; (Windows). Topics: docs-aliases Site aliases overview with examples Aliases: rsync

    Read the article

  • Power cut during Ubuntu upgrade to 10.04 - boots to command line, apt-get and dpkg do not work.

    - by Macha
    I was upgrading Ubuntu to 10.04, when a tripswitch tripped, cutting power to the computer. When it was restarted, it booted into a command line prompt. Google tells me to try: sudo dpkg --configure -a This gets me a lot of output that ends with a list of packages. I can't tell you what the output is, as piping the output to more/less does not work (still just all scrolls by and moves to next prompt), and redirecting it to a file just results in an empty file. Google also suggested: sudo apt-get install -f This also didn't work. Is a fresh install the only solution at this point?

    Read the article

  • Need to run a .sh as root on boot or login

    - by Graymayre
    Still new with linux and running ubuntu 12.10 I have a wireless stick (ae2500) which has known issues that has been partially solved using ndiswrapper. However, to use it I must run the same scripts every time I reboot, effectively uninstalling and reinstalling the driver. I made a .sh file to run every time to make it easy, but I must do the sudo login everytime. There are three solutions I am looking for and although not all are necessary to solve this particular problem, I would still like to know them all for learning purposes. run scripts or file.sh on boot (as well as other programs) run scripts or file.sh automatically with root privileges make the install permanent so as not to have to go through the process every time. Any additional information that can help me regarding this that I did not think to ask (including streamlining my commands), or general knowledge, would be greatly appreciated. Following are the contents of the file. I pretty much just made it as I would have entered it. cd ~/ndiswrapper-1.58rc1 sudo modprobe -rf ndiswrapper sudo rm /etc/modprobe.d/ndiswrapper.conf sudo rm -r /etc/ndiswrapper/* sudo depmod -a sudo make uninstall sudo make sudo make install sudo ndiswrapper -i bcmwlhigh5.inf ndiswrapper -l sudo modprobe ndiswrapper

    Read the article

  • How to move ubuntu 12.04 on another drive

    - by Maksim
    How I can move my ubuntu on another drive? I know about clonezilla but problem is that destination drive is smaller the source one. Gparted can't copy-paste partition if destination not the end last partition. I tried dpkg --selected-packages and apt-clone. First one just not install all my packages and removed existed that now I have no full unity and not my all packages. Second one just fail on configuration package. But before I did that way I copy-paste my /etc to new system. My partition table destination : gpt 1 1049kB 106MB 105MB fat32 EFI System ??????????? 2 106MB 12,1GB 12,0GB ext4 3 12,1GB 66,3GB 54,2GB ext4 source: msdos 1 1049kB 12,0GB 12,0GB primary ext4 ??????????? 2 12,0GB 492GB 480GB primary ext4 3 492GB 500GB 8107MB primary linux-swap(v1) Gpt not working with ubuntu that use grub 1.99. I don't know why but my laptop can't boot any device with uefi just black screen and ubuntu detect it on fresh install.

    Read the article

  • Suggested ways of collecting 1000's of links to MSM media articles

    - by Matt
    I'm currently running a modified Wordpress site that is uniquely designed to simply publish links to other sites, similar to The Drudge Report. Right now I have a few dozen Google Alerts setup and go through each result manually and if it matches a few niche keywords I'm working with, then I add a link to the article to my site. I do the manual checking because sometimes Google Alerts finds links to sites that belong to service providers, organizations, or products, but all I want are mainstream news articles. So my question is there a more efficient - and ideally automated - way to go about performing highly qualitative searches and aggregating such links?

    Read the article

  • Problem in Installing Wordpress

    - by Hajloo
    I try to install Wordpress in a Windows Client with WebPI which provided by Microsoft. I had tostop installation process 3 time and installing PHP and mysql Extention manually. but everytime I continue setup by WebPi andfinally it show me a success message. But when I try to see installed wordpress in my client I see this Your PHP installation appears to be missing the MySQL extension which is required by WordPress. I asked it in StackOverFlow here but I couln't get the right answer. I install everything in **C:\Program files\** so these are the location C:\Program Files\MySQL\MySQL Server 5.1 C:\Program Files\Php C:\Program Files\ext mysql root password: admin wordpress database : wordpress wordpress database password : 123 here is my php.ini

    Read the article

  • Hybrid Graphics Functional won't work with my Asus UL30V anymore

    - by futuress
    The problem is that I am no longer able to boot in compatibility mode for just turning on my Nvidia graphics to install the driver. Because no login screen will appear if Ubuntu is loading. In Ubuntu 11.10 I was able to activate nvidia graphics only' option this way: 1) Change BIOS to 'compatibility mode' which will turn off the Intel card. 2) Install the Nvidia proprietary driver using Ubuntu's driver finder (Additional Drivers) and then reboot. I was not interested using only the Intel graphics, for the sake of battery life. Now I have both cards running and they drain my battery life dramatically. And the main problem of this configuration no OpenGL is available, so I can't play any games any more. At this point, I have a pre-solution. I uninstalled the nvidia drivers and installed bumblebee. Now the Intel card is recognized. I would prefer to run just the nvidia card as in Ubuntu 11.10 but for now this is better than nothing. Does anybody else have the same problem?

    Read the article

  • Cannot Restore GRUB (Ubuntu 11.04 + Win 7)

    - by Benny
    I'm trying to fix GRUB on my PC, but I'm running into serious issues doing so. Any help would be greatly appreciated as I'm completely crippled right now. Here is the sequence of events for this PC: Installed Windows 7 Split full disk into two partitions (one for win7 and one for multimedia) Long time passed Split one of the partitions into two again Installed Ubuntu 11.04 on new partition A little time passed Windows 7 acting up, reinstall Ubuntu GRUB gone Tried restoring GRUB by mounting and grub-install from live USB Tried switching to a live CD instead of USB (thinking it might be the drive) Now I don't see GRUB and I'm getting "input/output" errors An example i/o error: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xbe86aff6 Device Boot Start End Blocks Id System /dev/sda1 * 1 48727 391393280 7 HPFS/NTFS /dev/sda2 48727 77063 227612647+ 7 HPFS/NTFS /dev/sda3 77063 91202 113566721 5 Extended /dev/sda5 77063 90622 108908544 83 Linux /dev/sda6 90622 91202 4657152 82 Linux swap / Solaris ubuntu@ubuntu:~$ sudo mount /dev/sda5 /mnt ubuntu@ubuntu:~$ sudo grub-install --root-directory=/mnt /dev/sda mkdir: cannot create directory `/mnt/boot': Input/output error ubuntu@ubuntu:~$ cd /mnt ubuntu@ubuntu:/mnt$ ls ls: cannot access etc: Input/output error

    Read the article

  • How do I correct the kernel version loaded by Grub2 in Ubuntu 12.04

    - by Paul D'Ambra
    I have a linux vps running Ubuntu 12.04 and when I run uname-r it replies: paul@webforms:~$ uname -r 2.6.32.33-kvm-i386-20111128-dirty paul@webforms:~$ sudo grub-install -v grub-install (GRUB) 1.99-21ubuntu3.1 if I run update-grub I get: paul@webforms:~$ sudo update-grub Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.2.0-26-generic-pae Found initrd image: /boot/initrd.img-3.2.0-26-generic-pae Found linux image: /boot/vmlinuz-2.6.38-15-generic-pae Found initrd image: /boot/initrd.img-2.6.38-15-generic-pae done and then rebooting gives me the same dirty kernel I'm going round in circles and as a relative noob I'm sure I must be missing something obvious so over to the hive-mind!!

    Read the article

  • Problems with Ubuntu and AMD A10-4655M APU

    - by Robert Hanks
    I have a new HP Sleekbook 6z with AMD A10-4655M APU. I tried installing Ubuntu with wubi--the first attempt ended up with a 'AMD unsupported hardware' watermark that I wasn't able to remove (the appeared when I tried to update the drivers as Ubuntu suggested) On the second attempted install Ubuntu installed (I stayed away from the suggested drivers) but the performance was extremely poor----as in Windows Vista poor. I am not sure what the solution is--if I need to wait until there is a kernel update with Ubuntu or if there are other solutions--I realise this is a new APU for the market. I would love to have Ubuntu 12.04 up and running--Windows 7 does very well with this new processor so Ubuntu should, well, be lightening speed. The trial on the Sleekbook with Ubuntu 12.10 Alpha 2 release was a complete failure. I created a bootable USB. By using either the 'Try Ubuntu' or 'Install Ubuntu' options resulted in the usual purple Ubuntu splash screen, followed by nothing...as in a black screen without any hint of life. Interestingly one can hear the Ubuntu intro sound. In case you are wondering, this same USB was trialed subsequently on another computer with and Intel Atom Processor. Worked flawlessly. Lastly the second trial on the Sleekbook resulted in the same results as the first paragraph. Perhaps 12.10 Beta will overcome this issue, or the finalised 12.10 release in October. I don't have the expertise to know what the cause of the behaviour is-the issue could be something else entirely. Sadly, the Windows 7 performance is very good with this processor-very similar and in some instances better to the 2nd generation Intel i5 based computer I use at my workplace. Whatever the cause is for the performance with Ubuntu 12.04 or 12.10 Alpha 2, the situation doesn't bode well for Ubuntu. Ubuntu aside, the HP Sleekbook is a good performer for the price. I am certain once the Ubuntu issue is worked on and solutions arise, the Ubuntu performance will probably be better than ever.

    Read the article

  • Desktop interface crashes after software updates

    - by N.C. Weber
    Recently, after installing Ubuntu software updates on the evening of December 7th, 2012, my desktop interface crashes regularly leaving me with a command line screen with a long string of automated commands showing (I assume what goes on behind the pretty desktop). At first, I thought it was only crashing whenever I played DirectX games in WINE, but now it crashes if I open the native Firefox browser or if it's doing nothing at all but sitting there. Apport attempts to report the bugs after restart, but often they crash as well. I've done a SMART check on the hard drive, and everything report OK. No read errors, no bad sectors. I am using an Acer Extensa 4620Z Memory: 2.0 GiB Processor: Intel Pentium Dual CPU T2370 @ 1.73GHz x 2 GraphicsL: Intel 965GM x86/MMX/SSE2 OS: Ubuntu 12.10 32-bit Disk: 116.0 GB with 33.4 GB Available

    Read the article

  • Clear OS always showing "Operation too slow. Less than 1 bytes/sec"

    - by Blue Gene
    Have been trying to install clear os addon but nothing is working as i am facing this error on every mirror in the .repo file. Yum install squid http://mirror2-dallas.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on http://mirror2-dallas.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror2-dc.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror2-dc.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror1.timburgess.net/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror1.timburgess.net/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror2-houston.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror2-houston.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror3-toronto.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror3-toronto.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror2-dallas.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror2-dallas.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'O*peration too slow. Less than 1 bytes/sec transfered the last 30 seconds'*) Trying other mirror. mirror2-dc.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror2-dc.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror1.timburgess.net/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror1.timburgess.net/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. mirror3-toronto.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: [Errno 12] Timeout on mirror3-toronto.clearsdn.com/clearos/core/6/x86_64/repodata/primary.sqlite.bz2: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds') Trying other mirror. Error: failure: repodata/primary.sqlite.bz2 from clearos-core: [Errno 256] No more mirrors to try. How can i fix this.i am able to access repo through web,and it seems nothing wrong with the repo.Where can be the problem. Tried yum clean all but it also didnt help. Is there a way to fix it as i am not able to install any package in it.

    Read the article

  • Installing Ubuntu on Asus G75VW (UEFI)

    - by user101653
    You all are my last hope... help! I bought an Asus G75VW from Best Buy. It has the new UEFI BIOS instead of the old style BIOS (1980's) and has Windows 8 preinstalled. I cannot get the G75VW to install Ubuntu 12.10 in EFI mode. I did get Ubuntu to load if I changed the BIOS to CSM and the computer sees and installs Ubuntu in "legacy mode". I attempted boot repair, and Ubuntu will load after 1 minute but as legacy BIOS only. If I changed the BIOS to UEFI "Binary is whitelisted" is displayed and I get a purple screen. My goal... keep my preinstalled Windows 8 on internal drive bay 1 and install Ubuntu 12.10 on internal drive bay 2... and somehow make a choice on which to choose. I am at a loss. I am a software programmer, but I am very bad at understanding BIOS and partitioning. Any ideas? Has anyone done what I want to do. This is a full second day on my "issue"! If I cannot get Ubuntu installed, I'm returning the laptop. And "wait" until these obstacles of UEFI/EFI and properly handled to allow people to load EFI based Ubuntu without a hitch. Thanks, Dave

    Read the article

  • How do I create a Windows 7 USB installer with preinstalled software?

    - by Marcel
    I was wondering if it was possible to make a bootlable image of a Windows 7 Pro OEM Installation CD that I have and put it on an USB stick for faster/easier installation. I am asking because we have a couple of PC´s where I´d have to install the OS using the same key (MAK). Also is it possible to kind of populate that image with software that would have to be installed anyways on all machines (like Chrome, Outlook, etc)? It would be really helpful to just install a Windows 7 image with customized software already installed. I would just make an image of an OS and use that, but the hardware of the machines differ.

    Read the article

  • Fix for poor hd playback for 11.04 upwards

    - by mark kirby
    Hi guys ive seen loads of posts on this site about poor 720/1080p playback in recent ubuntu versions I had this problem and fixed it so I thought id share it with everyone.... 1 install mplayer 2 install smplayer frontend {in software center} 3 open smplayer 4 go to "OPTIONS" then "PREFRENCES" then "GENRAL" 5 if you have a nvidia card choose "OUTPUT DRIVER" and select "VDPAU" {for ATI or AMD choose xv (0 - ATI Radeon AVIVO video) I dont know if this will work as my card is nvidia but it should) 6 go to performance on the left hand side and set both local and streaming cache to 99999 (this may also fix dvd playback if you set that cache aswell} 7 check the box for "ALLOW HARD FRAME DROP" and set "LOOP FILTER" to skip only on HD 8 Set the "THREDS FOR DECODING OPTION TO THE NUMBER OF CORES YOUR CPU HAS IF YOU HAVE MORE THAN ONE CPU ADD UP ALL THE CORES FOR BEST PERFORMANCE" 9 Enjoy you HD movies again on ubuntu...... I have a pretty avrage machine heres my spec.... 2x Pentium 4 ht 3 ghz Stock dell power and motherboard GFORCE 310 HDMI 24 inch full HD tv as a monitor so any one with dule core cpu should have no problems getting this to work. hope this helps someone out.

    Read the article

< Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >