Search Results

Search found 42646 results on 1706 pages for 'vbox question'.

Page 343/1706 | < Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >

• Unable to connect to shared (iscsitarget) dvd-rw drive on ubuntu karmic box

  - by Develop7

  Intro I have desktop with DVD-RW drive that runs primarily on Linux (namely Ubuntu 9.10). My wife has netbook that rins Windows XP with no cd/dvd drive. There's also LAN through our ADSL modem/router. I've "ported" (actually, I've just grabbed sources and ran dpkg-buildpackage) iscsitarget package from Ubuntu Lucid to Karmic (here are packages), installed it (sudo aptitude install iscsitarget; sudo m-a a-i iscsitarget) and configured it in the following way (/etc/ietd.conf): Target iqn.2020-01.local.develop7-desktop:storage.disc.dvdrw Lun 0 Path=/dev/sr0,Type=blockio #I've skipped commented lines Also, I've opened port 3260 with ufw: $ sudo ufw status | grep 3260 3260 ALLOW 192.168.1.0/24 Problem But (here's the trouble) I still can't connect to this target from Windows box. Microsoft Software iSCSI Initiator screams "Logon failure" upon connect attempt, and, respectively, fails to connect. After unsuccessful connection attempt I've noticed this line in dmesg | tail's output: iscsi_trgt: ioctl(299) invalid ioctl cmd c078690d Question So the question is — what's wrong with my config/iSCSI target/whatever else? Or, in short — what I'm doing wrong? Thanks in advance.

  Read the article

• What service do you use for music on hold?

  - by Russ Warren

  This may not be a sysadmin question for some, but it is definitely a hurdle I have to jump as the sysadmin for my company. We recently rolled-out a company wide VoiP system (Switchvox, to be exact) that has come preloaded with some royalty-free music on hold. Our customers have been complaining that the music on hold sounds like "funeral music." This may be the case (although I wouldn't want it played at my funeral), but it is all we have and we aren't willing to be sued over using music that isn't properly licensed. So, that brings me to the question asked in the title -- what and/or how do you provide decent music on hold? I'm assuming many people here use a PBX that allows customized music, so this has to apply to many of you. We've been looking at some sites that allow you to download royalty-free music for a one-time fee, but the music seems...lame. Something like a one-year subscription from ibaudio.com seems to be the best bet so far. Have you been able to discover something a little more mainstream for a decent licensing fee? Thank you. EDIT: Our PBX allows the playback of MP3 and OGG files, but does not allow streaming of a live audio source, Internet-based or otherwise. It also does not allow the use of a "line-in" source such as a CD player or radio. Don't let this stop you from sharing your setup, though. I'm interested in hearing what everyone uses!

  Read the article

• iis7 large worker process request queue creating process blocking aspnet.config & machine.config amended (bottleneck)

  - by scott_lotus

  ASP.net 2.0 app .net 2.0 framework IIS7 I am seeing a large queue of "requests" appear under the "worker process" option. State recorded appear to be Authenticate Request and Execute Request Handles more than anything else. I have amended aspnet.config in C:\Windows\Microsoft.NET\Framework64\v2.0.50727 (32 bit path and 64 bit path) to include: maxConcurrentRequestsPerCPU="50000" maxConcurrentThreadsPerCPU="0" requestQueueLimit="50000" I have amended machine.config in C:\Windows\Microsoft.NET\Framework64\v2.0.50727\CONFIG (32 bit and 64 bit path) to include: autoConfig="true" maxIoThreads="100" maxWorkerThreads="100" minIoThreads="50" minWorkerThreads="50" minFreeThreads="176" minLocalRequestFreeThreads="152" Still i get the issue. The issue manifestes itself as a large number of processes in the Worker Process queue. Number of current connections to the website display 500 when this issue occurs. I dont think i have seen concurrent connections over 500 without this issue occurring. Web application slows as the request block. Refreshing the app pool resolves for a while (as expected) as the load is spread between the two pools. Application pool in question FIXED REQUEST have been set to refresh on 50000. Thank you for any help. Scott quick edit to say hmm, my develeopers are telling me the project was built with .net 3.5 framework. Looking at C:\Windows\Microsoft.NET\Framework64\v3.5 there does not appear to be a ASPNET.CONFIG or a MACHINE.CONFIG .... is there a 3.5 equivalent ? after a little searching apparenetly 3.5 uses the 2.0 framework files that 3.5 is missing. So back to the original question , where is my bottleneck ?

  Read the article

• Turning Google Apps mail inbox into Support Ticket System

  - by Saif Bechan

  I have an account at Google apps and most of my email is done trough Gmail. Now I just manually respond to support email. I was wondering if there is an easy way using filters and auto responders to create a support ticket system. I think something like this would be great, but is it possible: Gmail has to make a unique ID for every email that comes in. After that all the other incoming mails should be grouped using that unique ID and not grouped by email. Something like that, or are there things I am not taking into account. I really don't want to use separate software for this, because I think with some small configurations this can do the trick quite well. Or are there some free apps on the marketplace that do this already. I have searched for this but cannot find any. Sorry if this is not an SF question. I really didn't know which is the best fit for this question. This can be migrated to anywhere if someone things it would be answered better there.

  Read the article

• Java Swing over Remote Desktop - Strange, weird GUI squashing

  - by ADTC

  I thought this question fits SuperUser more than StackOverflow because it's not about actual Java programming, though programmers might be more likely to encounter the problem. Anyway, let me start of with some stats before I ask the actual question: Laptop: Windows 7 x32 Screen resolution 1024 x 768; Nvidia GeForce Go 6200 Connected to desktop via ad-hoc wireless network Access internet via desktop Desktop: Windows 7 x64 Screen resolution 1920 x 1080 Connected to laptop via ad-hoc wireless network Access internet via cable modem I'm connecting to my laptop via Remote Desktop from my desktop to take advantage of the large screen. I'm doing programming on my laptop (for portability reasons). Everything else runs smooth and fast over Remote Desktop as both computers are connected directly over the ad-hoc wireless. The only problem is this: Java Swing apps don't display the GUI properly. I acquired a Java Swing application and I'm debugging it in Eclipse. Here's what I got when I ran the app: Apparently there doesn't seem to be anything wrong with the GUI application I'm debugging, because the Java Control Panel exhibits the same problem. I've searched high and low in Google about this; the closest I came to a solution is this. But sadly, the use of -Dsun.java2d.nodraw=true has no effect at all. This only happens over Remote Desktop. I have tried locally and the GUI apps display properly. This isn't a dealbreaker for me as I can stop using Remote Desktop when developing Java Swing apps. However, I would like to know if anyone has encountered this and found any solution. PS: All software involved (Eclipse, Java JRE, etc.) are latest versions.

  Read the article

• how to design pound -> varnish -> jboss for ha + loadbalancing

  - by andreash

  Hello, I'm planning a new infrastructure for our web application. We have two JBossAS5 servers, running in a cluster. Session state will be replicated via JBoss Cache. In front of that, there should be some cache, to speed up delivery of static elements. However, most of the traffic to our app will be via HTTPS. So far, I had been thinking of two Varnish caches in front of the JBossASs, each being configured for loadbalancing to the two JBossASs via round-robin. Since Varnish doesn't handle HTTPS, then there would need to be two pound proxies in front of the Varnishs, dealing with the HTTPS. The two pounds would be made high-available with Heartbeat/LinuxHA. The traffic to www.example.com would then be going through our firewall, from there to the virtual IP of the pounds, from there to the Varnishs, and from there to the JBossASs. Question 1: Does this make sense? Or is it overly complicated, and the same goal can be reached with simpler methods? Question 2: If my layout is fine, how do I configure the pound - Varnish step? Should I a) make the Varnish service high-available through Heartbeat/LinuxHA as well and direct traffic from pound to the virtual IP of the Varnishs, or should I rather b) Configure two independent Varnishs and use load-balancing in pound to address the different Varnishs? Thanks a lot for your insight! Andreas.

  Read the article

• Should one have a separate user account for work use? [closed]

  - by Tyler Wayne

  This question examines the practice of using a separate OS-level user account to divide work use from personal use (specifically, in a creative profession and on a personal computer). I recently left my in-the-flesh job to go to school, but I'm carrying on with the work remotely. I do all of my work on my laptop, and I currently have a separate user account called "Work" where I do exactly that. However, I'm now starting to question that practice. Because my hobby is the same as my job, I want to save notes of the things I learn while working. Because ideas come at any moment, I often want to throw something into my personal task manager's inbox and look at it again later. That task manager is well-suited to handle both the work and personal aspects of my life. Only my personal account has admin rights, but work sometimes requires me to install programs. My employer has no preference regarding my choice, so that is a non-issue. My work is essentially freelance web development, so advice given with that in mind will be much appreciated. Back up all opinion with some personal experience, please. Ideally, give a list of pros and cons and then name reasons for your position.

  Read the article

• Tomcat deployment overwrites context.xml

  - by Kristoffer

  Hi, I'm pretty new to Tomcat in general, so please point out if got anything wrong. My question is regarding updates to already deployed apps, using the Tomcat manager. But first thing first. I'm using the META-INF/Context.xml for storing connection info for the database connections, so this is unique to every server the application is deployed to. I'm not sure if this is optimal but it's the only way I know. So, when updating the application, it's important that this file doesn't get modified, because I don't want to have to go in and remake all changes every time I update my app. For updating, I'm using the Tomcat Manager, and I've tried different approaches but everything seems to build on the process of undeploy, then deploy the new version. This way, the Context.xml gets removed/replaced by an empty Context.xml file. So my question is basically, how do I update a running webapp, and at the same time having the Context.xml left untouched? Btw, I'm running Tomcat 6.0.24.

  Read the article

• How to configure VirtualBox server for performance at home

  - by BluJai

  I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

  Read the article

• What does a DHCP-client consider to be the "best" answer?

  - by Nils

  We have training rooms where normally Windows XP is installed (via PXE). The "normal" DNS/DHCP infrastructure are Windows-Servers. The training room has its own VLAN (different from the Windows servers), so there is most propably an IP helper for DHCP requests active on the Cisco router where all PCs from that room are connected to. Now we wanted to convert some of the PCs to Linux instead. The idea was: Put our own Laptop with a DHCP server into the VLAN of the room and override the "normal" DHCP response. The idea was that this should work, since a directly attached DHCP server in that VLAN should have a faster response-time than the "normal" DHCP server located some hops away from that VLAN. It turned out that this did not work. We had to manually release the lease on the original DHCP server to get it working. On the Laptop we did see the client requesting the IP and "our" dhcp was sending NACKs to the Windows IP request, before that we did offer our own response. Old Question: Why did this not work out as expected? What is making the PC regain its old lease? Update 2012-08-08: The regain-issue has been explained in the DHCP-RFC. Now this explains why the PC regains its old lease. Now we do release the IP from the Windows-DHCP-server before giving it another try. Again - the Windows-DHCP-server wins. I suspect that there is some algorithm for the dhcp-client which determines the "best" dhcp-answer for the client. The new question is: How does the client choose the "best" answer?

  Read the article

• Parallel Environment (PE) on Sun Grid Engine (6.2u5) won't run jobs: "only offers 0 slots"

  - by Peter Van Heusden

  I have Sun Grid Engine set up (version 6.2u5) on a Ubuntu 10.10 server with 8 cores. In order to be able to reserve multiple slots, I have a parallel environment (PE) set up like this: pe_name serial slots 999 user_lists NONE xuser_lists NONE start_proc_args /bin/true stop_proc_args /bin/true allocation_rule $pe_slots control_slaves FALSE job_is_first_task TRUE urgency_slots min accounting_summary FALSE This is associated with the all.q on the server in question (let's call the server A). However, when I submit a job that uses 4 threads with e.g. qsub -q all.q@A -pe serial 4 mycmd.sh, it never gets scheduled, and I get the following reasoning from qstat: cannot run in PE "serial" because it only offers 0 slots Why is SGE saying "serial" only offers 0 slots, since there are 8 slots available on the server I specified (server A)? The queue in question is configured thus (server names changed): qname all.q hostlist @allhosts seq_no 0 load_thresholds np_load_avg=1.75 suspend_thresholds NONE nsuspend 1 suspend_interval 00:05:00 priority 0 min_cpu_interval 00:05:00 processors UNDEFINED qtype BATCH INTERACTIVE ckpt_list NONE pe_list make orte serial rerun FALSE slots 1,[D=32],[C=8], \ [B=30],[A=8] tmpdir /tmp shell /bin/sh prolog NONE epilog NONE shell_start_mode posix_compliant starter_method NONE suspend_method NONE resume_method NONE terminate_method NONE notify 00:00:60 owner_list NONE user_lists NONE xuser_lists NONE subordinate_list NONE complex_values NONE projects NONE xprojects NONE calendar NONE initial_state default s_rt INFINITY h_rt 08:00:00 s_cpu INFINITY h_cpu INFINITY s_fsize INFINITY h_fsize INFINITY s_data INFINITY h_data INFINITY s_stack INFINITY h_stack INFINITY s_core INFINITY h_core INFINITY s_rss INFINITY h_rss INFINITY s_vmem INFINITY h_vmem INFINITY,[A=30g], \ [B=5g]

  Read the article

• How can I systematically shut down Windows services in order?

  - by cbmeeks

  We have this open source application that has three (3) services. For the purpose of this question, let's call them A, B, and C. Now, they have to be shut down in a specific order. That order would be A then B then C. If B shuts down before A then we run into all kinds of problems. Same is true if C shuts down before B or A. Plus, each service can take a different amount of time to shut down due to how many users were using it. Oh, this need to be wrapped up in a DOS batch file or something a non-techy user could just double-click to initiate. (PowerShell is not out of the question but I've never used it). Also, I'm a C# coder so that could be used too. Anyway, when the restart is initiated the following needs to happen: 1) Initiate shutdown of service A 2) When service A is down, it should trigger the shutdown of service B 3) When service B is down, it should trigger the shutdown of service C 4) When service C is down, it should trigger the START UP of service A 5) When service A is UP, it should trigger the START UP of service B 6) When service B is UP, it should trigger the START UP of service C So as you can see, each stop/start needs to wait on the previous to be completely finished before moving on. And since each service can take a few seconds to a few minutes, we can't use any kind of timing tricks. Suggestions greatly appreciated. Thanks!

  Read the article

• Is basing storage requirements based on IOPS sufficient?

  - by Boden

  The current system in question is running SBS 2003, and is going to be migrated on new hardware to SBS 2008. Currently I'm seeing on average 200-300 disk transfers per second total across all the arrays in the system. The array seeing the bulk of activity is a 6 disk 7200RPM RAID 6 and it struggles to keep up during high traffic times (idle time often only 10-20%; response times peaking 20-50+ ms). Based on some rough calculations this makes sense (avg ~245 IOPS on this array at 70/30 read to write ratio). I'm considering using a much simpler disk configuration using a single RAID 10 array of 10K disks. Using the same parameters for my calculations above, I'm getting 583 average random IOPS / sec. Granted SBS 2008 is not the same beast as 2003, but I'd like to make the assumption that it'll be similar in terms of disk performance, if not better (Exchange 2007 is easier on the disk and there's no ISA server). Am I correct in believing that the proposed system will be sufficient in terms of performance, or am I missing something? I've read so much about recommended disk configurations for various products like Exchange, and they often mention things like dedicating spindles to logs, etc. I understand the reasoning behind this, but if I've got more than enough random I/O overhead, does it really matter? I've always at the very least had separate spindles for the OS, but I could really reduce cost and complexity if I just had a single, good performing array. So as not to make you guys do my job for me, the generic version of this question is: if I have a projected IOPS figure for a new system, is it sufficient to use this value alone to spec the storage, ignoring "best practice" configurations? (given similar technology, not going from DAS to SAN or anything)

  Read the article

• PC only boots from Linux-based media and won't boot from DOS-based media

  - by xolstice

  I have this problem where the PC only seems to boot from a floppy disk or CD if it was created as a Linux-based bootable media. If it was created as a DOS-based bootable media the system just freezes at the starting point of the boot process. I originally asked this under question 139515 for CD booting only, and based on the given answers, I was under the impression the problem was with the CD-ROM drive; however, I have since installed a newly purchased CD-ROM drive and the same freezing occurs. This then made me try the DOS bootable floppy disk approach and I was quite surprised that it exhibited the same freezing problem. I then tried try a Linux bootable floppy and everything booted from it without any issues. As I mentioned in my original question, the PC was booting just fine from the DOS-based bootable CD, and then it suddenly decides to pull this freezing stunt. I can't remember if I changed anything in the BIOS settings that may I have caused the problem, but I am wondering if that could be the case - it is currently using the Award Module BIOS v4.60PGMA. Can anyone help?

  Read the article

• How to configure VirtualBox server for performance at home

  - by BluJai

  I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

  Read the article

• Is this a File Header / Magic Number?

  - by Hammer Bro.

  I've got 120,000 files (way more, actually; this is just an arbitrary subset) of an unknown type. Linux file does not identify them (not that they're necessarily Linux files), nor do any other methods I've tried. There are only two hints about them that I currently have. One is that I suspect some compression is employed -- I have metadata that claims the file sizes are always some amount larger than what I observe. The other is that in 100,000 of these files, the first 16 bytes are always: ff ee ee dd 00 00 00 00 01 00 00 00 00 00 00 00 That really looks like a file header/magic number to me, but I just can't place it. Does anyone know what kind of files this would indicate? Alternatively, can anyone convince me that these suspiciously common bytes certainly do not indicate a specific file type? UPDATE I don't know the exact reverse-engineering details, but most of the files in our case are zips after the first 29(? or so) bytes are ignored. So in practice the problem is solved (we know how to process the files) but in theory the question is still unanswered -- I don't know which application routinely prepends about 29 bytes to its zips. [I'm not sure if I should leave the question open or not at this point.]

  Read the article

• Resize a RAID 1 volume on OSX Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OSX 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable...), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

• apache 2.4, mod_proxy_fcgi not honouring .htaccess, work around needed

  - by user229874

  I am using apache 2.4.7 with mod_proxy_fcgi for purpose of passing through php to php-fpm (this will be used for shared hosting environment). The htaccess works fine for non php files, but once it hit rewrite rule that proxies through the php requests, the htaccess is ignored. I know why it is happening. The question is: how do I work around it? The question how do I force apache to treat the request to php file as a request to local file, and then proxy it through? I have spent substantial time in researching on this problem, and following "answers" were given as solution: 1) "use apache configuration instead of .htaccess" it is valid solution, but not for shared hosting environment (I am not going to give access to apache configuration to shared hosting customers ;)). 2) "don't use .htaccess, as it has performance/security/other issues", well how else would shared hosting customers control access/url rewriting on their site? Besides if the .htaccess was not a requirement I would simply use nginx. 3) "put rewrite rule for proxy inside of " - this is incorrect, and it does not work. This behaviour appears to be not a bug but a "feature" as per https://issues.apache.org/bugzilla/show_bug.cgi?id=54887

  Read the article

• AutoHotkey - Organizing hotkeys so as to use Several hotkeys optimally

  - by Stenemo

  My question is how to structure key combinations in script below most effectively using AutoHotkey. Having searched for exactly how to do this for hours I figured I should post here so others can at least find this solution if they are trying to do the same: http://www.autohotkey.com/board/topic/90013-solved-wasd-fna-left-fnalta-home-fnctrla-ctrl-left-etc/ and How to combine three keys as a hotkey with Autohotkey? My Question is how to use this method most effectively, and is not answered in those threads. My idea would be to use this for everything related to up (etc), e.g.: ; Up Combinations: Ctrl Up, SHIFT + Up, SHIFT + Ctrl Up, [Alt/win + Up easily added and organized using this system] CapsLock & w:: GetKeyState, stateCtrl, LCtrl GetKeyState, stateShift, LShift GetKeyState, stateWin, LWin GetKeyState, stateAlt, LAlt if stateCtrl = D if stateShift = D if stateWin = D Send ^+#{Up}; Ctrl + SHIFT + Win + Up else Send ^+{Up} ; Ctrl + SHIFT + Up else if stateWin = D Send ^#{Up} ; Ctrl + Win + Up else Send ^{Up} ; Ctrl Up else if stateShift = D Send +{Up} ; SHIFT + Up else if stateWin = D Send #{Up} ; Win + Up else if stateAlt = D Send !{Up} ; Alt + Up else Send {Up} ; Up return Also, if there is a better way to do this, that would be great. E.g.: *CapsLock & w:: send {Up} Does almost exactly the opposite of what I want (sends up even if other modifiers are held down). When I hold e.g. control at the same time, I want it to do control + up. Have I missed such a AutoHotkey command? If anyone has a better way to do this that would be great.

  Read the article

• Cache updates when migrating DNS from one provider to another

  - by JohnCC

  This may be a Windows DNS specific question or a general DNS best practice question - I'm not sure! We migrated our 3rd party DNS provision from provider A to provider B. I noticed that our internal recursive windows DNS servers still had NS records cached for our domains pointing to provider A's servers, even though I changed the nameservers with our registrar several days ago, and even though selecting the properties of the cached records showed a TTL of 1 day. After 24 hours when the NS records in this cache have expired, will the DNS server go back to the TLD server for an update on the authority, or will it go by preference to dns1.providera.com since that is what it has cached? In this case I arranged to leave Provider A's servers up for a week to allow changes to propagate, so dns1.providera.com is still active and would still provide NS and SOA records that said that dns1.providera.com. was in charge of this domain. Given this fact, would the Windows DNS server ever go back to the TLD and pick up the authority changes, or would it just assume all was well and renew timestamps on its cached NS records? I wonder what would be the best approach to ensuring that caches pick this up. Should I:- (1) Leave Provider A's servers in place and active and wait for caches to catch up ... basically what we're doing now which seems to have issues - perhaps specifically for Windows servers, or perhaps more widely. (2) Leave Provider A's servers in place but change the NS and/or SOA information they provide to tell caches that new servers are in charge. (3) Remove Provider A's servers after 2*TTL to force remaining caches to update. The issue with (2) is that on Provider A's system I can't seem to change the NS or SOA information to anything other than their servers. The issue with (3) is that I'm not sure how a DNS server would behave in this case. When it couldn't reach the cached name servers, would it flush its cache and try a full recursive lookup, or would it just return an error, forcing the user to clear the cache manually? Thanks in advance!

  Read the article

• Why is a FLAC encoded from a decoded MP3 bigger than the MP3?

  - by Ryan Thompson

  To be more precise than in the title, suppose I have a MP3 file that is 320 kbps. If I decompress it, then logically, all the data except for roughly 320 kilobits out of each second of audio should be redundant data, able to be compressed away. So, when I encode the decompressed file to FLAC, or any other lossless codec, why is it so much larger? On a related note, is it theoretically possible to losslessly recover the source mp3 audio from a decompressed wav? (I know the mp3 itself is lossy. I'm asking if it's possible to re-encode without any further loss.) EDIT: Let me clarify the related question, and the rationale behind it. Suppose I have a wav that was decompressed from an MP3 file (and assume I don't have the mp3 itself for some reason). If I don't want to lose any more quality, I can re-encode it with FLAC or any other lossless encoder and get a larger file just to maintain the same quality. Or, I can re-encode it to mp3 again and get the same size as the original but lose more data. Obviously, neither of these cases is ideal. I can either have the original size or the original quality, but not both (I mean the quality of the original mp3, not the original lossless source). My question is: Can we get both? Is it theoretically possible to recover the lossy compressed data from the lossy decompressed data, without losing even more? If it is possible, I could imagine a lossless compression algorithm that compresses the audio with FLAC. Then it also scans the audio for any signs of previous lossy compression, and if detected, recompresses it losslessly to the original lossy file. Then it keeps whichever file is smaller.

  Read the article

• How to use DNS/Hostnames or Other ways to resolve to a specific IP:Port

  - by tomaszs

  This is a Canonical Question about DNS/Hostnames resolution to IPs/Ports Example 1 I'm running a web server on port 80 and another on port 87. I would like to use DNS so that www.example.com goes to port 87. How can I accomplish this using DNS only? Example 2 I'm running a service on my server on a non-standard port. How can I get clients to connect to this non-standard port automatically? Can I use DNS? Is there some application specific support where DNS could indicate the IP and Port? Example 3 Do some application protocols specifically support hostname awareness, and allow special actions to be taken based on this information? Are there other questions on Server Fault that cover some of these? Commandeering: This question was originally asking about running IIS and Apache on the same server, but the same concepts can be applied to any server software receiving connections from clients. The Answers below describe the technical problems and solutions of using DNS and application protocol support to assign a port number for a client to connect.

  Read the article

• Virtualbox - differencing disk based on different differencing disk

  - by Klinki

  I'm trying to create differencing image based on differencing image in VirtualBox 4.2.18. Official documentation says it should be possible: http://www.virtualbox.org/manual/ch05.html#diffimages Basically I want to achieve this drive hierarchy: + immutable image with Debian and all software installed +---- differencing image with specific configuration, autoreset=off, readonly +-------- differencing image with autoreset=on +---- another differencing image for different virtual machine +-------- differencing image with autoreset=on I successfully created differencing image based on differencing image, but I'm not able to connect it to virtual machine :( It always shows error: Failed to open the hard disk .... cannot register hard disk ... because hard disk with UUID ... already exists Here is screenshot of Virtual Media Manager and error dialog Virtual Media Manager Window screenshot Very strange is that the new differencing image (tempdrive.vdi) doesn't have Actual Size 0. I wasn't able to connect it, but still, it has 36KB of data on it... This is very similar to this older question: How to create a chained differencing disk of another differencing disk in Virtual Box? but suggested solution is not working anymore in VirtualBox 4.2.18, so I posted it as a new question. (Limit for posting links and screenshots is quite annoying..)

  Read the article

• Which internet scenario would be better?

  - by JL

  I currently have an 8mbps (down) / 512kbps (up) telephone ADSL solution. I must say the reliability is excellent, and up until now its been the fastest connection I could get because I don't live in a cable zone. The real speed of my connection is around 7mbps, but sometimes I manage to get the full 8mbps. I use my connection for work, so it needs to be at least 99% reliable. Recently I was told by a guy who lives up the road that he has a wireless connection with an external antenna and his speeds are 20mbps / 512kbps - he's also paying about 1/2 of what I pay for my wired telephone connection. My question is, is wireless internet good enough for a power user who uses his connection for work 8 hours a day, including VPNing into servers remotely. Besides this I also enjoy playing the odd network game, not a WoW freak, but sometimes I do pick up the odd MMORPG and at times do indulge in some semi heavy gaming sprees. Will this wireless latency drive me crazy and seem slow in comparison? Will it be reliable enough, I also live in an area that snows heavily in winter. I guess its a question of - should I go wireless or not. I've only had 1 wireless connection before and that was years ago using iBurst technology and I remember it was terrible for VPN, but I guess the technology might have been improved since then? What do you guys think?

  Read the article

• sql 2008 disk layout on a budget this is for database mirroring

  - by user22215

  Guys I'm rolling out a SQL database server that will be used to back Sharepoint 2007. Right now I need some advice on my disk layout. I have two Dell servers that are configured a little differently in terms of storage. The principle server will be using a combination of local storage and san storage. I have to work with what I have the organization is currently all allocated on san storage it was like pulling teeth to even get what I have to work with now. My disk setup on the principle is as follows: raid 1 for OS raid 10 for logs raid 10 fiber on san for high IO databases raid 10 sata on san for content databases My question in regards to the principle server is where should I place the temp db? I thought about placing it on the fiber raid 10 which will be hosting my high IO Sharepoint SSP databases my only other choice is to move it to the raid 1 os partition which I’m sure you guys will be against. Now let’s talk about the mirror server it is not connected to the san it is all local 6 15k SAS drives. Now my question is the same do I put tempdb on the os partition or do I leave the os partition and use a single raid 10 for everything? Any help you can provide is much appreciated.

  Read the article

< Previous Page | 339 340 341 342 343 344 345 346 347 348 349 350  | Next Page >