Search Results

Search found 11707 results on 469 pages for 'boot failure'.

Page 344/469 | < Previous Page | 340 341 342 343 344 345 346 347 348 349 350 351  | Next Page >

• Should I use "Raid 5 + spare" or "Raid 6"?

  - by Trevor Boyd Smith

  What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

  Read the article

• Intermittent extrememly long response times when downloading documents

  - by pap

  I have a Java web application running om Tomcat 7 with an Apache httpd 2.2 fronting with mod_jk/AJP. One part of the application is serving files (up to 4mb size). Now, normally this all runs very smooth with stable, low response-times. However, in rare instances (<0.1% of downloads), the downloadtime will go beyond 1 minute. After activating the ThreadStuckValve in Tomcat, I can see that the long responses seem to be stuck at org.apache.tomcat.jni.Socket.sendbb(Native method) i.e network I/O. At most, these long-running downloads take 5 minutes, which I strongly suspect is because of the default 300 second timout in Apache 2.2 (http://httpd.apache.org/docs/2.2/mod/core.html, "TimeOut directive"). To me, this looks like network problems. The Apache timeout (if that is what is kicking in at the 5 minute mark) indicates that ACK packets are not being transmitted correctly. My questions are what could be causing this? Closed browser at receiving end but socket not signaled as closed properly? Packet loss or some other network failure in transit? Where would I start troubleshooting this? We're running Tomcat and Apache on Windows server 2008-R2 in a vmware virtualized server.

  Read the article

• ATI firepro will not detect a second DVI-D monitor

  - by John

  OK so weird issue here. I have previously been running 6 screens off of 3 of the older ATI firepro graphics cards but they had a problem with the heat sink getting too hot and warping the PCB resulting in total failure of the card, to replace my three dead cards I purchased a new-type ATI firepro with the newer heat sink design. I'm only using one at the moment to make sure they've fixed the problem before I waste more money on 2 more cards but this is where things start to get weird. The Firepro's only have one port on them, they connect to two monitors via a splitter cable going from the one port to two DVI connectors for the screens. When I plug two identical monitors in via their DVI inputs not matter what I do windows and Catalyst will only detect one screen. However if I use the VGA input on one of the screens with a VGA - DVI adaptor to plug it in to the card it works fine. This confuses me greatly. I'm currently using the ATI Firepro 2270 Graphics card with identical DELL U2311H screens. I can post the rest of the system spec as well if needed but I wouldn't have thought it would make much difference as it had no problem handling 6 screens before the graphics cards failed. Naturally both catalyst and ATI drivers are the most current version. ATI tech support has been absolutely zero help, they seemed to get stumped as soon as I verified that both screens were plugged in and connected properly. Anyone have any ideas?

  Read the article

• Mailman delivery troubles

  - by stanigator

  I have apparently posted at the wrong place (superuser.com) for this question, so I'll just repost it here. Hope those of you who read both sites are not going to be offended. It's about mailing list management software called Mailman from GNU. Here are the details: Hosting provider: Vlexofree Domain: www.sysil.com with Google Apps Mailing List created from hosting cpanel: [email protected] I have registered a list of subscribers, and tried sending an email to [email protected]. I got the following error message: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550-5.1.1 The email account that you tried to reach does not exist. Please try 550-5.1.1 double-checking the recipient's email address for typos or 550-5.1.1 unnecessary spaces. Learn more at 550 5.1.1 http://mail.google.com/support/bin/answer.py?answer=6596 23si6479194ewy.44 (state 14). ----- Original message ----- MIME-Version: 1.0 Received: by 10.216.90.136 with SMTP id e8mr1469147wef.110.1264220118960; Fri, 22 Jan 2010 20:15:18 -0800 (PST) Date: Fri, 22 Jan 2010 20:15:18 -0800 Message-ID: <[email protected]> Subject: From: Stanley Lee <[email protected]> To: [email protected] Content-Type: multipart/alternative; boundary=0016e6dab0931bccc3047dcd2f1e - Show quoted text - Is there any way of fixing this problem? I would like to be able to have this mailing list to work through my hosting and domain. Thanks in advance.

  Read the article

• SSL connection error for only one site (of many) on server

  - by Matt Lacey

  I have a server running many websites, each with SSL. One of the sites is now refusing connections over SSL. This was previously working and I'm looking for assistance in determining what has been changed. Here's the situation: http://site1.com/ - works https://site1.com/ - works http://site2.com/ - works https://site2.com/ - Doesn't work (but did previously) Both sites are on the same server (Win Server 2003 SP2 - IIS6) Both sites use certificates from the same authority and are both valid (according to IIS). As far as I can tell, both sites have certificates configured identically in IIS. (Checked by a manual/visual check of properties, side by side) Through use of OpenSSL I can see that there's a "ssl handshake failure" when trying to connect to site2 using https. What could be the cause of this? How can I investigate further? Without SSL connections being available to this site, users are unable to log in or register. :( disclaimer: I'm not a server admin and not responsible for the box. Yes, there are wider issues here but I need to get this working again first.

  Read the article

• Generalized strategy for file server virtualization in Xenserver

  - by Jamie

  I'm not shopping as much as I'm looking for some guidance on good idea / bad idea strategies. I'm sure I'm not in the "best practices" budget range. Currently, I have 3 dell poweredges running xenserver in a pool. Each node has a ubuntu file server, serving about 6TB. One is the primary, the other two are rsync targets for backup. The 6TB is stored on their respective local storage disks as an LVM of 3x2tb virtual disks. The fileserver VM disks are also stored on the node local disks. Each node also runs a smattering of light-weight VMs for web, development, windows VMs, and stuff like that. Several of those VM's disks reside on a QNAP NAS to play with live migration. These VM's are often clients of the primary file server (like all the mail, web content, user files are stored on the file server, not on the mail, web, and samba VMs). This all works fine, and is a major step up for us. The downside is that the QNAP is a single point of failure. And the only thing the QNAP is doing is serving migratable VM images, not client data. Someday the poweredge local arrays will be full, and we will have to reinvent ourselves again. Is it wise to have heavywieght vms (like the fileserver, with its 6+ TB disks) on a SAN or NAS? Would it be better to keep the VMs lightweight, have the VM images on a SAN or NAS, and use 2 or more NAS act as NFS-serving file appliances? A hybrid SAN/NAS that can serve iscsi for images and NFS for the client vms? It seems like live-magration would be a misnomer if you have to migrate a fileserver with its entire 6+ TB disk. I recognize there are plenty of ways to skin the cat. We've already skinned it a few ways. What makes sense?

  Read the article

• Mystery 0xc0000142 error on starting java from a service, as a different user.

  - by cpf

  This is a very convoluted setup, but effectively this is what goes down: Manager service (which I don't have control over) running as admin user X starts my executable, which then starts Java as user Y using the standard c# StartInfo.Username/Password controls. Now, from a basic (not elevated or anything, just admin) command prompt I can run that executable, and Java pops up and works fine, running perfectly under the user it should be. When the service runs the same executable, however, Java silently fails. The only hint I see is this series of events in the event viewer: Service starts "Application popup: java.exe - Application Error : The application was unable to start correctly (0xc0000142). Click OK to close the application. " (googling this reveals a lot of scam sites telling me to use their "free antivirus to fix 0xc0000142 errors easy!"... sigh) Service stops (the java shutdown propagated, which is supposed to happen) And here's what process explorer has for the failure: As you can see, everything shows as a success. Now, I think this might have something to do with the permissions (the user java.exe is running under has traverse permission for the entire drive and full permissions to Directory A, which is where the .jar is), but I just can't fathom how something that works fine from the command line (and, this is an upgrade, the previous system without the user-switching aspect works fine from the service) can fail with such a cryptic message and little showing up in logs.

  Read the article

• Strange Internet Connection issues

  - by Nodren

  I'm attempting to troubleshoot problems with a laptop computer(HP 8510w) while it's connected to a server of mine via Remote Desktop. I double checked all the settings on the win2k3 server for remote desktop to verify that remote desktop isn't what's causing the disconnect issues, and other people using different computers/laptops can all connect to remote desktop correctly with no issues. These problems happen specifically when the laptop is connected via wifi(several different wifi sources, so it's not an ISP issue) as well as connected via a Verizon data card. However there's no network downtime when the laptop is resting in the docking station and plugged into the network with the remote desktop server. These problems have also only recently occurred since a recent hard drive failure in which a new hard drive was purchased and the laptop had a fresh install of windows xp professional. There's no special software used on this machine, just office 2003. So my question is, what could cause two types of internet access to fail while other types do not? If it is infact related to the win2k3 server, why is this particular laptop getting disconnected when others are not and are all on at the same time?

  Read the article

• RPC Server Unavailable on Hyper-V cluster when moving resources after the host adapter has failed

  - by Doug Luxem

  On a Windows 2008 R2 SP1 cluster running Hyper-V, a lost network connectivity on the primary host interface. The interface was rapidly flapping up and down, and this was later determined to be caused by a faulty switch port. As this was a clustered server, the host interface was not fault tolerant (seeing as how the whole server was fault tolerant), so connectivity to the host was going up and down. The Hyper-V guests were completely unaffected by the network outage as they used a dedicated trunk on the server separate from the host interface. Additionally, dedicated interfaces for the cluster and live migration networks were fine. In order to diagnose the server, I tried to move all resources (Hyper-V Guests) to other nodes through Failover Cluster Manager. These moves failed with an error RPC Server Unavailable. The only way to move resources was by shutting down the guests, stopping the cluster service on the Node A, allowing other nodes to take ownership of the resources, and restarting the guests. A few other notes: All nodes have Client for MS Networks and File & Printer Sharing enabled on the Cluster and LM networks. Node A was accessible over cluster and LM networks from other nodes (these are private, cluster-only networks); pingable, CIFs, etc. Accessing \\NODEA is done over the Host adapters, as you would expect in this case and is the reason for the RPC Server Unavailable error with that adapter being down. My questions here are - Is there a way to still use Live Migration in a failure scenario such as this to prevent shutting down the Hyper-V guests? How can the network be reconfigured in the future so that the cluster service attempts to use the cluster and/or live migration networks to issue the RPC requests?

  Read the article

• Running KVM/XEN/Hyper-V VMs from a RAM disk, is this possible? Practical?

  - by Ausmith1

  Currently I'm using ESX (v3 and v4) to test a scripted OS (Windows 2003) and application install DVD. The DVD ISO (8GB) is mounted on a 1Gbps NFS datastore and the VMDK's (20GB) are on an SSD mounted via NFS over a 10Gbps link. It still takes a lot longer than I'd really like for to run through a test iteration and I'm wondering if mounting the virtual disks and ISO on a RAM disk on the same server as the hypervisor is running on would be worth my while. I can dedicate a server to this VM and 32GB of RAM in the system should be adequate to do the trick I'd guess. (1GB hypervisor OS, 28GB RAM disk and 2GB for the VM is < the 32GB available to me) Since hosting a RAM disk within ESX does not seem possible I'm open to trying KVM/Xen/Hyper-V. KVM would probably be my first choice of these three. Anyone out there tried this? Bear in mind this is purely for a test run of the installer, the VM will be discarded as soon as the test is completed so I'm not worried about losing data from the remote possibility of a power failure.

  Read the article

• Mongo daemon restarts after replica set issue

  - by Matt Beckman

  We had a recent election in our replica set (2 read nodes; 1 write node) that changed the primary node. Curious as to why this occurred, I started looking through the logs to find out what happened. It appears that mongoNode2 could not communicate with mongoNode3. When both nodes could not communicate, it appears that this caused the services on mongoNode2 and mongoNode3 to restart, eventually resulting in a new primary after the services had been started again. Thu Jun 23 08:27:28 [ReplSetHealthPollTask] DBClientCursor::init call() failed Thu Jun 23 08:27:28 [ReplSetHealthPollTask] replSet info mongoNode3:27017 is down (or \ slow to respond): DBClientBase::findOne: transport error: mongoNode3:27017 query: { \ replSetHeartbeat: "myReplSet", v: 3, pv: 1, checkEmpty: false, from: \ "mongoNode2:27017" } Thu Jun 23 08:27:29 got kill or ctrl c or hup signal 15 (Terminated), will \ terminate after current cmd ends Thu Jun 23 08:27:29 [interruptThread] now exiting Thu Jun 23 08:27:29 dbexit: Is there any reason that the mongo service would restart due to a DBClientCursor::init call() failure? Is this a known bug? It should be noted that mongoNode2 and mongoNode3 are VMs on the same VMware host. MongoNode1 is not on the same host, and it did not have any issues with the service. However, I did not have any other reports of issues with other VMs on the VMware host.

  Read the article

• Missing whole disk device in OpenSolaris

  - by Jeff Mc

  I have begun experimenting with Solaris and ZFS as a NAS. All was going very smoothly until I had a drive failure. When I replaced the drive, I no longer have a device file mapped to the whole disk. /dev/dsk/c7t3d0 does not exist but c7t2d0 and c7t4d0 both do. Also the sd@3,0:wd file under the /devices/ tree is non-existent. Do I have to prepare/partition the disk somehow to cause the whole disk device to exist? Here are a few outputs that might be useful. jeffmc@ats-ds2:/dev/dsk$ zpool status pool: datapool state: DEGRADED status: One or more devices could not be opened. Sufficient replicas exist for the pool to continue functioning in a degraded state. action: Attach the missing device and online it using 'zpool online'. see: http://www.sun.com/msg/ZFS-8000-2Q scrub: none requested config: NAME STATE READ WRITE CKSUM datapool DEGRADED 0 0 0 mirror-0 DEGRADED 0 0 0 c7t2d0 ONLINE 0 0 0 c7t3d0 UNAVAIL 0 0 0 cannot open mirror-1 ONLINE 0 0 0 c7t4d0 ONLINE 0 0 0 c7t5d0 ONLINE 0 0 0 jeffmc@ats-ds2:/dev/dsk$ zpool replace datapool c7t3d0 cannot open 'c7t3d0': no such device in /dev/dsk must be a full path or shorthand device name jeffmc@ats-ds2:/dev/dsk$ sudo format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c7t0d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@0,0 1. c7t1d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@1,0 2. c7t2d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@2,0 3. c7t3d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@3,0 4. c7t4d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@4,0 5. c7t5d0 /pci@0,0/pci8086,3599@6/pci8086,330@0/pci1014,2cc@7,1/sd@5,0

  Read the article

• Standards for documenting/designing infrastructure

  - by Paul

  We have a moderately complex solution for which we need to construct a production environment. There are around a dozen components (and here I'm using a definition of "component" which means "can fail independently of other components" - e.g. an Apache server, a Weblogic web app, an ftp server, an ejabberd server, etc). There are a number of weblogic web apps - and one thing we need to decide is how many weblogic containers to run these web apps in. The system needs to be highly available, and communications in and out of the system are typically secured by SSL Our datacentre team will handle things like VLAN design, racking, server specification and build. So the kinds of decisions we still need to make are: How to map components to physical servers (and weblogic containers) Identify all communication paths, ensure all are either resilient or there's an "upstream" comms path that is resilient, and failover of that depends on all single-points of failure "downstream". Decide where to terminate SSL (on load balancers, or on Apache servers, for instance). My question isn't really about how to make the decisions, but whether there are any standards for documenting (especially in diagrams) the design questions and the design decisions. It seems odd, for instance, that Visio doesn't have a template for something like this - it has templates for more physical layout, and for more logical /software architecture diagrams. So right now I'm using a basic Visio diagram to represent each component, the commms between them with plans to augment this with hostnames, ports, whether each comms link is resilient etc, etc. This all feels like something that must been done many times before. Are there standards for documenting this?

  Read the article

• LDAP Account Locked Out Sporadically after Password change - Finding the source of invalid attempts

  - by CityView

  On a small network of machines (<1000) we have a user whose account is being locked out after an indeterminate interval following a password change. We are having severe difficulties finding the source of the invalid logon attempts and I would appreciate it greatly if some of you could go through your thought process and the checks you would perform in order to fix the problem. All I know for sure is that the account is locked out several (5+) times a day, I can't even be sure it's due to failed login attempts as there is no record of failure until the account is locked. So far I have tried; Logging the account out of everything we can think of and back in with the new password Scanning the user's box for any non standard software which might perform an LDAP lookup Checking all installed services on our production boxes to check none are attempting to run under the account Changing the user back to their old password (Problem persists so perhaps password change is a red herring) Wireshark on a box where lots of LDAP authentication is performed - Rejects only occur after account is already locked out Clearing the credential cache in - Control Panel - User Accounts - Advanced Looking at the local I'm at a loss for what to try. I am happy to try any suggestions you have in order to diagnose the issue. I think my question boils down to a simple request; I need a technique for deriving the source (Application/Host) of the invalid login attempts which are causing the account to be locked. I'm not sure if that's even possible but I suspect there must be more I can try. Many thanks, CityView

  Read the article

• Reliable custom Windows shortcut keys?

  - by Peter Baer

  I have global Windows shortcut keys assigned to several different cmd.exe instances. I do this by creating shortcuts to cmd.exe on my desktop, and assigning each one a unique shortcut key (for example, CTRL + SHIFT + U). Pretty basic stuff. I'm using Win2K8 (R1 and R2). This works just fine... most of the time. But with infuriating regularity, sometimes it doesn't. Or it will work with a long delay (many seconds). It doesn't matter what app currently has focus (it can even be one of the command prompts). It doesn't matter what keys I assign (I've tried a few variations of WIN, CTRL and SHIFT). I did notice that this is often, but not always, correlated with explorer.exe struggling in some way or another (say, an explorer window opened to a file share that's unavailable, or an app being unresponsive, or whatever). In other words the shortcut key handling appears to be very sensitive to unrelated system activity. Note that whenever I have this problem I can always successfully ALT + TAB to the window I want to get to, but that's tedious. I use the shortcuts to these command windows hundreds of times a day so even a 1% failure rate becomes really annoying. Is there a way to fix this, or is there some third-party utility out there that will RELIABLY intercept custom key combinations to bring focus to whatever apps I want, in a way that is independent of other system activity? ADDENDUM: There is a property of the Windows shortcuts that I would not want to lose if switching to a third-party hotkey tool: Windows shortcuts are idempotent. Once you've launched a shortcut to some app, pressing the shortcut key combo again takes you to the already launched process - it does not launch a new process.

  Read the article

• Problems installing Windows service via Group Policy in a domain

  - by CraneStyle

  I'm reasonably new to Group Policy administration and I'm trying to deploy an MSI installer via Active Directory to install a service. In reality, I'm a software developer trying to test how my service will be installed in a domain environment. My test environment: Server 2003 Domain Controller About 10 machines (between XP SP3, and server 2008) all joined to my domain. No real other setup, or active directory configuration has been done apart from things like getting DNS right. I suspect that I may be missing a step in Group Policy that says I need to grant an explicit permission somewhere, but I have no idea where that might be or what it will say. What I've done: I followed the documentation from Microsoft in How to Deploy Software via Group Policy, so I believe all those steps are correct (I used the UNC path, verified NTFS permissions, I have verified the computers and users are members of groups that are assigned to receive the policy etc). If I deploy the software via the Computer Configuration, when I reboot the target machine I get the following: When the computer starts up it logs Event ID 108, and says "Failed to apply changes to software installation settings. Software changes could not be applied. A previous log entry with details should exist. The error was: An operations error occurred." There are no previous log entries to check, which is weird because if it ever actually tried to invoke the windows installer it should log any sort of failure of my application's installer. If I open a command prompt and manually run: msiexec /qb /i \\[host]\[share]\installer.msi It installs the service just fine. If I deploy the software via the User Configuration, when I log that user in the Event Log says that software changes were applied successfully, but my service isn't installed. However, when deployed via the User configuration even though it's not installed when I go to Control Panel - Add/Remove Programs and click on Add New Programs my service installer is being advertised and I can install/remove it from there. (this does not happen when it's assigned to computers) Hopefully that wall of text was enough information to get me going, thanks all for the help.

  Read the article

• How to organise storage for media content such as video and music?

  - by thor

  Currently, we have a single server hosting all content: music, video and software. This content is downloaded by users through HTTP. Now free space is coming to an end and we are exploring different ways of extending our storage capacity. We want to do it cheap, simple and reliable (protected from disk/ server faults). Currenly, we see two ways: Add a couple of cheap servers with 4 disks (RAID1 ?), run some distributed file-system on top, like GlusterFS. Pros: hopefully, we will see all our disks as single flat file system, just dump content into it and be done. Cons: could be tricky in configuration and handling of faults. Add a couple of cheap servers, all running HTTP servers. Each piece of content (be it a music file or video) is placed on randomly selected two servers. Pros: don't have to deal with RAID, as content is duplicated; single server failure does not bring down any part of content; doubled distribution capacity (as any signle file could be downloaded from any of two servers hosting it). Cons: requires some scripting on part of distribution of content, adding/ removing servers. Do we miss any other ways? Which of the aforementioned options seems to be the best?

  Read the article

• Windows XP hanging on login screen

  - by Nathan W

  I have been given two Eee PC 100HA to manage for some people, they are both running the same hardware and XP home but one is having some strange problems with logging on. The main problem is that it hangs at the login screen for ages and sometimes never gets to the desktop. The strange thing is it only seems to do it after the computer has been cold started, but it won't do it if the computer has been restarted. I have made two logs of the start up with process monitor but every time the logger is attached the computer will log in fine. I have also set the computer to blue screen and create a crash dump when you press ctrl scroll twice but when I do it at the hung login it just sits at a black screen and I don't get a crash dump, I have turned off the auto system restart on failure option also. I can usually fix most computer start up and shutdown problems but this one has got me stuffed. Has anyone had the same problems before, or can recommend something that I can try? Cheers.

  Read the article

• Methods to transfer files from Windows server to linux server

  - by Raze2dust

  Hi, I need to transfer webserver-log-like-files containing periodically from windows production servers in the US to linux servers here in India. The files are ~4 MB in size each and I get about 1 file per minute. I can take about 5 mins lag between the files getting written in windows and them being available in the linux machines. I am a bit confused between the various options here as I am quite inexperienced in such design: I am thinking of writing a service in C#.NET which will periodically archive, compress and send them over to the linux machines. These files are pretty compressible. WinRAR can convert 32 MB of these files into a 1.2 MB archive. So that should solve the network transfer speed issue. But then how exactly do I transfer files to linux? I could mount linux drive on windows server using samba, or should I create an ftp server, or send the file serialized as a POST request. Which one would be good? Also, I have to minimize the load on the windows server. Mount the windows drive on linux instead. I could use the mount command or I could use samba here (What are the pros and cons of these two?). I can then write the compressing and copying part in linux itself. I don't trust the internet connection to be very stable, so there should be a good retry mechanism and failure protection too. What are the potential gotchas in these situations, and other points that I must be worried about? Thanks, Hari

  Read the article

• Startup script for Red5 on Ubuntu 9.04

  - by user49249

  I am creating startup script for Red5 on Ubuntu. Red5 is installed in /opt/red5 Following is a working script on a CentOS Box on which Red5 is running [code] ==========Start init script ========== #!/bin/sh PROG=red5 RED5_HOME=/opt/red5/dist DAEMON=$RED5_HOME/$PROG.sh PIDFILE=/var/run/$PROG.pid # Source function library . /etc/rc.d/init.d/functions [ -r /etc/sysconfig/red5 ] && . /etc/sysconfig/red5 RETVAL=0 case "$1" in start) echo -n $"Starting $PROG: " cd $RED5_HOME $DAEMON >/dev/null 2>/dev/null & RETVAL=$? if [ $RETVAL -eq 0 ]; then echo $! > $PIDFILE touch /var/lock/subsys/$PROG fi [ $RETVAL -eq 0 ] && success $"$PROG startup" || failure $"$PROG startup" echo ;; stop) echo -n $"Shutting down $PROG: " killproc -p $PIDFILE RETVAL=$? echo [ $RETVAL -eq 0 ] && rm -f /var/lock/subsys/$PROG ;; restart) $0 stop $0 start ;; status) status $PROG -p $PIDFILE RETVAL=$? ;; *) echo $"Usage: $0 {start|stop|restart|status}" RETVAL=1 esac exit $RETVAL [/code] What do I need to replace for Ubuntu in the above script. My Red5 is in /opt/red5/ and to start it manually I always do /opt/red5/dist/red5.sh from Ubuntu As I did not find rc.d/functions on Ubuntu on my laptop also /etc/init.d/functions I did not existed. I would like to be able to use them with service as Red hat distributions do. I checked /lib/lsb/init-functions.

  Read the article

• Good Enough Failover Strategy for DNS / MySQL / Email

  - by IMB

  I've asked and read a lot questions regarding DNS failover but the more I read the more complicated it becomes, some people say it's good enough some say it isn't. No clear answers from what I read. I was wondering if we can set it straight once and for all, at least for the requirements of most websites out there. Right now let's assume the following: We don't need really need load-balancing, what we need is a failover solution. We are running a website based on LAMP on a VPS. We need to make sure that the Web Server, MySQL, Email are always accessible if not 99%. Basically here's my idea and questions about it: Web Server: We need at least one failover server (another VPS on a separate data center). Is DNS Failover via Round Robin good, if not, what's the best? And how do you exactly implement it? How do you make the files you upload/delete on Server A is also on Server B? MySQL: I've only read a brief intro to MySQL replication and I assume that I can replicate Server A to Server B and vice versa on the fly right? So just it case Server A fails and Server B is now running, it will continue to work and replicate to Server A when it becomes available. So in essence Server B is now the primary server, and will later on failover to Server A, should a failure happen again. Email: If we are gonna use DNS Failover, using webmail or relying on emails stored on the server is probably not a good idea right? Since some emails might be on Server A while some might be on Server B? I assume a basic email forwarder to a 3rdparty is good enough (like Gmail for example) to ensure all emails are kept in one place. Here's a basic diagram for a better picture: http://i.stack.imgur.com/KWSIi.png

  Read the article

• Laptop Most Likely to Have Good Driver Support

  - by ShabbyDoo

  Through numerous bad experiences, I have learned that the most likely cause of laptop "failure" is the lack of updated drivers for new operating systems. As an example, I have a perfectly good Thinkpad T42 at home which runs Windows 7 just fine for my purposes except that no compatible ATI video drivers are available, and the generic drivers have flicker effects. I recently saw an ASUS laptop which looked quite nice except that I would be beholden to them to release ATI video driver updates customized for it. And, I can't trust them to do that for more than six months. What laptops (manufacturer/line) should I consider so that I could expect at least a couple years of frequent updates? I plan on running Windows 7 and installing whatever successor comes out. I like Intel components (especially WiFi) because I can install their drivers directly from them, and they have a long history of providing updates for years after shipping a particular component. More generally, components from companies which are likely to update drivers frequently are good as long as I can install the component manufacturer-provided drivers without laptop-specific customization (like the ATI drivers). Also, if a component can be replaced easily, I am less concerned. For example, Dell stopped pumping out updated drivers for one of its mini-PCI WiFi cards. The solution was to buy an Intel replacement on eBay for $12! That's fine. I can deal with that. So, what laptops should I consider so that I'm not likely to be stuck between a rock and a hard place?

  Read the article

• I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

  - by ChrisF

  Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

  Read the article

• Intermittently uncommunicative subnets

  - by mhd

  Last week proved me a veritable Cassandra: I've always said that it's a bad idea to have only one firewall/router, without a backup or failover. And thus our Cisco PIX went haywire, refusing to route properly. And of course, the only one available here on short notice is me, and while I'm quite grounded in Linux, I'm really a developer not a sysadmin (the fact that this hit me on sysadmin appreciation day is a bit ironic). Anyway, this weekend I tried to hack up a temporary solution: I used an old server with enough NICs (two built-in, four on a card) to serve as a gateway and firewall. Due to some problems with the raid controller, I got only two router distros running, and between Untangle and Ebox I decided for the latter. Now everything is quite okay. I've got all the different subnets we've got here (all with separate switches) talking to each other and even to the internet (Cisco 2800 router, T1 lines). But from time to time (20-60 minute intervals), I get a total routing failure. Our main, office subnet can't talk to our server subnet and can't connect to the internet. This is not the end of a gradual slowdown, either everything's working perfectly or I get a total lack of communication for about two minutes each time. Now I'm a bit at wits end what to check. At least with the default EBox setup, nothing in /var/log shows anything weird and it doesn't exactly have lots of built-in monitoring tools. So I'm hoping someone here could give me some pointers about what to look out for. I did change the ethernet cable from the office switch to the firewall, with no results. I might change switches, although within the switch it seems to work ok enough. Edit: I'm not sure whether this is the sole cause of the problem, but after I noticed a few DHCP entries just before the last drop of connectivity, I tried to reproduce that. And alas, whenever I renew a DHCP connection, I can't access other subnets anymore. Running ISC DHCPD 3.0.6.

  Read the article

• Distributed storage and computing

  - by Tim van Elteren

  Dear Serverfault community, After researching a number of distributed file systems for deployment in a production environment with the main purpose of performing both batch and real-time distributed computing I've identified the following list as potential candidates, mainly on maturity, license and support: Ceph Lustre GlusterFS HDFS FhGFS MooseFS XtreemFS The key properties that our system should exhibit: an open source, liberally licensed, yet production ready, e.g. a mature, reliable, community and commercially supported solution; ability to run on commodity hardware, preferably be designed for it; provide high availability of the data with the most focus on reads; high scalability, so operation over multiple data centres, possibly on a global scale; removal of single points of failure with the use of replication and distribution of (meta-)data, e.g. provide fault-tolerance. The sensitivity points that were identified, and resulted in the following questions, are: transparency to the processing layer / application with respect to data locality, e.g. know where data is physically located on a server level, mainly for resource allocation and fast processing, high performance, how can this be accomplished? Do you from experience know what solutions provide this transparency and to what extent? posix compliance, or conformance, is mentioned on the wiki pages of most of the above listed solutions. The question here mainly is, how relevant is support for the posix standard? Hadoop for example isn't posix compliant by design, what are the pro's and con's? what about the difference between synchronous and asynchronous opeartion of a distributed file system. Though a synchronous distributed file system has the preference because of reliability it also imposes certain limitations with respect to scalability. What would be, from your expertise, the way to go on this? I'm looking forward to your replies. Thanks in advance! :) With kind regards, Tim van Elteren

  Read the article

< Previous Page | 340 341 342 343 344 345 346 347 348 349 350 351  | Next Page >