Search Results

Search found 25088 results on 1004 pages for 'dsl linux'.

Page 347/1004 | < Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >

• Motherboard/PSU crippling USB and Sata

  - by celebdor

  I very recently bought a new desktop computer. The motherboard is: Z77MX-D3H and the power supply is ocz zs series 550w. The issue I have is that once I boot to the operating system (I have tried with fedora and Ubuntu with kernels 2.6.38 - 3.4.0), my hard drive (2.5" Magnetic) occasionally makes a power switch noise and it resets. Needless to say, when this drive is the OS drive, the OS crashes. I also have a SSD that works fine with the same OS configurations, but if I have the magnetic hard drive attached as second drive, it works erratically and the reconnects result in corrupted data. I also noticed that whenever I plug an external hard drive USB2.0 or USB3.0 to the computer the issue with the reconnects is even worse: [ 52.198441] sd 7:0:0:0: [sdc] Spinning up disk... [ 57.955811] usb 4-3: USB disconnect, device number 3 [ 58.023687] .ready [ 58.023914] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.023919] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.023932] sd 7:0:0:0: [sdc] Sense not available. [ 58.024061] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024063] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024064] sd 7:0:0:0: [sdc] Sense not available. [ 58.024099] sd 7:0:0:0: [sdc] Write Protect is off [ 58.024101] sd 7:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 58.024135] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024137] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024400] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.024402] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024405] sd 7:0:0:0: [sdc] Sense not available. [ 58.024448] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024450] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024451] sd 7:0:0:0: [sdc] Sense not available. [ 58.024469] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024471] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024472] sd 7:0:0:0: [sdc] Attached SCSI disk [ 58.407725] usb 4-3: new SuperSpeed USB device number 4 using xhci_hcd [ 58.424921] scsi8 : usb-storage 4-3:1.0 [ 59.424185] scsi 8:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 59.424406] scsi 8:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 59.425098] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 59.425176] ses 8:0:0:1: Attached Enclosure device [ 59.425248] ses 8:0:0:1: Attached scsi generic sg3 type 13 [ 61.845836] sd 8:0:0:0: [sdc] 976707584 512-byte logical blocks: (500 GB/465 GiB) [ 61.845838] sd 8:0:0:0: [sdc] 4096-byte physical blocks [ 61.846336] sd 8:0:0:0: [sdc] Write Protect is off [ 61.846338] sd 8:0:0:0: [sdc] Mode Sense: 47 00 10 08 [ 61.846718] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.846720] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.848105] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.848106] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.857147] sdc: sdc1 [ 61.858915] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.858916] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.858918] sd 8:0:0:0: [sdc] Attached SCSI disk [ 69.875809] usb 4-3: USB disconnect, device number 4 [ 70.275816] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd [ 70.293063] scsi9 : usb-storage 4-3:1.0 [ 71.292257] scsi 9:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 71.292505] scsi 9:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 71.293527] sd 9:0:0:0: Attached scsi generic sg2 type 0 [ 71.293668] ses 9:0:0:1: Attached Enclosure device [ 71.293758] ses 9:0:0:1: Attached scsi generic sg3 type 13 [ 73.323804] usb 4-3: USB disconnect, device number 5 [ 101.868078] ses 9:0:0:1: Device offlined - not ready after error recovery [ 101.868124] ses 9:0:0:1: Failed to get diagnostic page 0x50000 [ 101.868131] ses 9:0:0:1: Failed to bind enclosure -19 [ 101.868288] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868292] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868296] sd 9:0:0:0: [sdc] Sense not available. [ 101.868428] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868434] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868439] sd 9:0:0:0: [sdc] Sense not available. [ 101.868468] sd 9:0:0:0: [sdc] Write Protect is off [ 101.868473] sd 9:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 101.868580] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868584] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868845] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868849] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868854] sd 9:0:0:0: [sdc] Sense not available. [ 101.868894] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868898] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868903] sd 9:0:0:0: [sdc] Sense not available. [ 101.868961] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868966] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868969] sd 9:0:0:0: [sdc] Attached SCSI disk Now, if I plug the same drive to the powered usb 2.0 hub of my monitor, the issue is not reproduced (at least on a 20h long operation). Also the issue of the usb reconnects is less frequent if the hard drive is plugged before I switch on the computer. Does anybody have some advice as to what I could do? Which is the faulty part/s that I should replace? As for me, I really don't know if to point my finger to the PSU or the Motherboard (I have updated to the latest firmware and checked the BIOS settings several times). EDIT: The reconnects are happening both in the Sata connected drives and the USBX connected drives.

  Read the article

• syntax highlighting in vim?

  - by ajsie

  on my ubuntu server vim got no syntax highlighting when i open files (configurations, scipts...). i have tried with :syntax on :syntax enable and it ways in vim that its enabled, but it doesnt work someone knows how to fix it? thanks!

  Read the article

• Server load high, CPU idle. NFS the cause?

  - by Mech Software

  I am running into a scenario where I'm seeing a high server load (sometimes upwards of 20 or 30) and a very low CPU usage (98% idle). I'm wondering if these wait states are coming as part of an NFS filesystem connection. Here is what I see in VMStat procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 1 0 1298784 0 0 0 0 16 5 0 9 1 1 97 2 0 0 1 0 1308016 0 0 0 0 0 0 0 3882 4 3 80 13 0 0 1 0 1307960 0 0 0 0 120 0 0 2960 0 0 88 12 0 0 1 0 1295868 0 0 0 0 4 0 0 4235 1 2 84 13 0 6 0 0 1292740 0 0 0 0 0 0 0 5003 1 1 98 0 0 4 0 0 1300860 0 0 0 0 0 120 0 11194 4 3 93 0 0 4 1 0 1304576 0 0 0 0 240 0 0 11259 4 3 88 6 0 3 1 0 1298952 0 0 0 0 0 0 0 9268 7 5 70 19 0 3 1 0 1303740 0 0 0 0 88 8 0 8088 4 3 81 13 0 5 0 0 1304052 0 0 0 0 0 0 0 6348 4 4 93 0 0 0 0 0 1307952 0 0 0 0 0 0 0 7366 5 4 91 0 0 0 0 0 1307744 0 0 0 0 0 0 0 3201 0 0 100 0 0 4 0 0 1294644 0 0 0 0 0 0 0 5514 1 2 97 0 0 3 0 0 1301272 0 0 0 0 0 0 0 11508 4 3 93 0 0 3 0 0 1307788 0 0 0 0 0 0 0 11822 5 3 92 0 0 From what I can tell when the IO goes up the waits go up. Could NFS be the cause here or should I be worried about something else? This is a VPS box on a fiber channel SAN. I'd think the bottleneck wouldn't be the SAN. Comments?

  Read the article

• Removing DS_Store files and variants?

  - by Ron Gejman

  Hi, I am running an Ubuntu 10.04.1 LTS server. Frequently I open up files using AFP from my Mac. Inevitably this created .DS_Store files on the server (although for some reason they are named :2eDS_Store. However, it also creates variants on DS_Store files. These variants are often named similarly to other files in that directory. E.g.: ~$ ls total 60K -rw-r--r-- 1 tarakhovsky 16K 2010-11-30 18:28 :2eDS_Store drwx--S--- 4 tarakhovsky 4.0K 2010-11-08 13:58 :2eTemporaryItems/ lrwxrwxrwx 1 tarakhovsky 15 2010-10-19 17:44 bigdisk -> /media/bigdisk// ... drwxr-xr-x 3 tarakhovsky 4.0K 2010-11-03 18:24 Temporary Items/ drwxr-xr-x 3 tarakhovsky 4.0K 2010-11-30 01:34 tmp/ ... I've disabled creation of DS_Store files using: defaults write com.apple.desktopservices DSDontWriteNetworkStores true so hopefully this won't continue to occur—but I really want to get rid of all of the existing variants of DS_Store files already on the server. Any ideas as to why these variants are being created and how I can get rid of them all?

  Read the article

• Command-line way to send keystrokes to a window open on a different X-session

  - by Sanjay Manohar

  I have a Ubuntu desktop open and logged on, on my main machine. I am then also logging in to this machine from a remote computer, using X2go which creates a new X-session. I have a libreoffice file open on the original session. I want to save this file and close it - but from the remote machine! (Both sessions have same user logged in; I can sudo if needed) I have tried using xdotool search but this fails to find the window. Is there a way to do what I want from this second session? I can see the process with ps -A I can even see the open file with lsof! How can I do a "save-and-close" on it?

  Read the article

• Dialog Connect to Server in Gnome Nautilus contains no items

  - by abatishchev

  I have installed Gnome Nautilus 2.28.4 on my Debian 5.0 box and a dialog File - Connect to Server - Service type is almost empty: How can I fix that?

  Read the article

• Can not boot CentOS VM using VirtIO in KVM

  - by Jake

  I converted qcow2 image to raw and changed I/O bus to VirtIO for a VM. now I can't boot that VM. I Installed VirtIO driver with following command: mkinitrd --with virtio_pci --with virtio_blk -f /boot/initrd-$(uname -r).img $(uname -r) and these are related kernel modules: virtio_balloon 11329 0 virtio_blk 11593 3 virtio_pci 11845 0 virtio_ring 8513 1 virtio_pci virtio 9541 3 virtio_balloon,virtio_blk,virtio_pci and this is what happens during boot-up. I also changed /boot/grub/device.map from "(hd0) /dev/sda" to "(hd0) /dev/vda" but problem still exists. any ideas how to fix this ? This is my default option to boot: title CentOS (2.6.18-308.13.1.el5) root (hd0,0) kernel /vmlinuz-2.6.18-308.13.1.el5 ro root=/dev/VolGroup00/LogVol00 initrd /initrd-2.6.18-308.13.1.el5.img

  Read the article

• zabbix monitoring mysql database

  - by krisdigitx

  I have a server running multiple instances of mysql and also has the zabbix-agent running. In zabbix_agentd.conf i have specified: UserParameter=multi.mysql[*],mysqladmin --socket=$1 -uzabbixagent extended-status 2>/dev/null | awk '/ $3 /{print $$4}' where $1 is the socket instance. From the zabbix server i can run the test successfully. zabbix_get -s ip_of_server -k multi.mysql[/var/lib/mysql/mysql2.sock] and it returns all the values However the zabbix item/trigger does not generate the graphs, I have created a MACRO for $1 which is the socket location {$MYSQL_SOCKET1} = '/var/lib/mysql/mysql2.sock' and i use this key in items to poll the value multi.mysql[{$MYSQL_SOCKET1},Bytes_sent] LOGS: this is what i get on the logs: 3360:20120214:144716.278 item [multi.mysql['/var/lib/mysql/mysql2.sock',Bytes_received]] error: Special characters '\'"`*?[]{}~$!&;()<>|#@' are not allowed in the parameters 3360:20120214:144716.372 item [multi.mysql['/var/lib/mysql/mysql2.sock',Bytes_sent]] error: Special characters '\'"`*?[]{}~$!&;()<>|#@' are not allowed in the parameters Any ideas where the problem could be? FIXED {$MYSQL_SOCKET1} = /var/lib/mysql/mysql2.sock i removed the single quotes from the line and it worked...

  Read the article

• Can I get advice on my nginx configuration (as a proxy in front of Jira and Confluence)?

  - by Nate

  I was wondering if I could get some advice on my nginx configuration. The config seems to be working, but I'm unsure if I'm doing everything properly. The basic idea is to have a Jira and Confluence server (in separate Tomcat instances) running on the same machine, with nginx in front to handle SSL for both. I want only SSL connections to be made to Jira/Confluence. Jira is running on 127.0.0.1:9090 and Confluence on 127.0.0.1:8080. Here is my nginx.conf, any advice or tips would be greatly appreciated. user nginx; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] $request ' '"$status" $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; #gzip on; # Load config files from the /etc/nginx/conf.d directory include /etc/nginx/conf.d/*.conf; # Our self-signed cert ssl_certificate /etc/ssl/certs/fissl.crt; ssl_certificate_key /etc/ssl/private/fissl.key; # redirect non-ssl Confluence to ssl server { listen 80; server_name confluence.example.com; rewrite ^(.*) https://confluence.example.com$1 permanent; } # redirect non-ssl Jira to ssl server { listen 80; server_name jira.example.com; rewrite ^(.*) https://jira.example.com$1 permanent; } # # The Confluence server # server { listen 443; server_name confluence.example.com; ssl on; access_log /var/log/nginx/confluence.access.log main; error_log /var/log/nginx/confluence.error.log; location / { proxy_pass http://127.0.0.1:8080; proxy_set_header X-Forwarded-Proto https; proxy_set_header Host $http_host; } error_page 404 /404.html; location = /404.html { root /usr/share/nginx/html; } redirect server error pages to the static page /50x.html error_page 500 502 503 504 /50x.html; location = /50x.html { root /usr/share/nginx/html; } } # # The Jira server # server { listen 443; server_name jira.example.com; ssl on; access_log /var/log/nginx/jira.access.log main; error_log /var/log/nginx/jira.error.log; location / { proxy_pass http://127.0.0.1:9090/; proxy_set_header X-Forwarded-Proto https; proxy_set_header Host $http_host; } error_page 404 /404.html; location = /404.html { root /usr/share/nginx/html; } # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { root /usr/share/nginx/html; } } }

  Read the article

• OpenOffice Daemon Problem

  - by mp_gt

  Dear all, I'm using OpenOffice as a daemon. Sometimes, when the daemon is running a long time, CPU use spikes very high and then openoffice crash. At this point, the open office applicattion don't work and the documents don't be generated. How can I restart automatically the openoffice daemon when this problem happens? Is there any way to monitor the service or to program a watchdog to handle it? Thanks in advance, regards.

  Read the article

• how to `tail` the latest file in a directory

  - by Itay Moav

  In shell, how can I tail the latest file created in a directory?

  Read the article

• echo newline character not working in bash

  - by Bashuser

  I have bash script which has lots of echo statements and also I aliased echo to echo -e both in .bash_profile and .bashrc, so that new lines are printed properly for a statement like echo 'Hello\nWorld' the output should be Hello World but the output I am getting is Hello\nWorld I even tried using shopt -s expand_aliases in the script, it doesn't help I am running my script as bash /scripts/scriptnm.sh; if I run it as . /scripts/scriptnm.sh I am getting the desired output...

  Read the article

• How to upgrade XMBC Live from 9.04.1 to 9.11?

  - by sunpech

  I've been unable to do a fresh install of XBMC Live 9.11 to my hard drive. Everytime it fails at the Install System step. But I am able to get XBMC Live 9.04.1 to install successfully. How do I upgrade XBMC Live 9.04.1 to 9.11? I understand that Ctrl+Shift+F2 brings up the command line, but what are the next set of commands to run?

  Read the article

• Can't figure out why hard drive is full [closed]

  - by Belgin Fish

  Possible Duplicate: How do I find out what is using up all the space on my / partition? No Free disk space so I have 2 hard drives in my server, one main one that is 10gb and then a separate one that is 2tb I'm storing all the files on the second one and the df -h output looks like this Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.2G 8.8G 0 100% / tmpfs 1.5G 0 1.5G 0% /lib/init/rw udev 1.5G 148K 1.5G 1% /dev tmpfs 1.5G 0 1.5G 0% /dev/shm /dev/sda4 1.8T 747G 981G 44% /home /dev/sda4 1.8T 747G 981G 44% /usr/lib/cgi-bin I just can't figure out why the first one is full when all the files are being stored in the /usr/lib/cgi-bin I'm running debian I can't seem to find any files that would take up 8.8gb that arn't on the second hard drive :S Thanks!

  Read the article

• Apache configuration to access directory

  - by Felipe Hummel

  I'm on Ubuntu 9.10. My web application is in a directory on my /home/me/app . I want to configure Apache in such a way that I can access my app through a directory. For example: People can access my machine through domain.com. What I would like to do is access my web application (located at /home/me/app) through a directory, using something like: domain.com/myapp. How can I set up the apache configuration for this kind of behavior? Of course, I do not want to move all my application to /var/www/myapp. Thanks

  Read the article

• How may I run a user process at system startup that the user can set himself?

  - by Eduardo

  I would like the users of the system to be able to setup processes that run at system startup that they can setup by themselves. How may I do it?

  Read the article

• Explanation of command to uppercase the first letter of a filename

  - by hazielquake

  I'm trying to learn to rename files with the command line, and after browsing around a lot of pages I finally found a command that uppercases the first letter of a file, but the problem is that I want to understand the meaning of each command. The command is: for i in *; do new=`echo "$i" | sed -e 's/^./\U&/'`; mv "$i" "$new";done I understand the 'for' kinda... but not the 'echo' or '`' and especially the sed command. if someone has a little patience to explain the meaning of each thing that'd be awesome! Thanks!

  Read the article

• Server not sending a SYN/ACK packet in response to a SYN packet

  - by jeff

  Using iptraf, tcpdump and wireshark I can see a SYN packet coming in but only the ACK FLAG is set in reply packet. I'm running Debian 5 with kernel 2.6.36 I've turned off window_scaling and tcp_timestamps, tcp_tw_recycle and tcp_tw_reuse: cat /etc/sysctl.conf net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_tw_reuse = 0 net.ipv4.tcp_window_scaling = 0 net.ipv4.tcp_timestamps = 0 I've attached an image of the wireshark output. http://imgur.com/pECG0.png Output to netstat netstat -natu | grep '72.23.130.104' tcp 0 0 97.107.134.212:18000 72.23.130.104:42905 SYN_RECV I've been doing everything possible to find a solution and have yet to figure out the problem, so any help/suggestions are much appreciated. UPDATE 1: I've set tcp_syncookies = 0 and noticed I am now replying with 1 SYN+ACK for every 50 SYN requests. The host trying to connect is sending a SYN request about once every second. PCAP FILE

  Read the article

• Configuring Apache for multiple clients

  - by Chris_K

  Last week I had a question here about suexec / suphp but I tried to accomplish too much. I'm going to narrow the scope a bit and try again. I'd like to configure a LAMP server to host multiple clients. I'd like it to seem (from the client's viewpoint) just like any other shared hosting environment. Web sites in their home directory, no need to muck around with file ownerships to get pages served, etc. It would seem that a configuration that involves suexec and suphp is the way to go(?) I'm specifically looking for a current/modern guide on how to accomplish this (I'll be using CentOS if it matters) and I'm afraid I need more than a link to Apache docs. Are there any good How-To's out there? The few I've found have been pretty out of date, but it is quite possible my search was weak.

  Read the article

• Force an LXC container to use its own IP address

  - by emma sculateur

  Sorry if this question has already been asked. I could not find it, I have this setup : +---------------------------------------------------------------------------------------------+ |HOST | | | | +-------------------------------------------------+ | | | UBUNTU-VM | | | | | | | | +-------------------+ | | | | |UBUNTU-LXC | | +------------------+ | | | | 10.0.0.3/24 | 10.0.0.1/24 | |OTHER VM | | | | | eth0-----lxcbr0----------eth0-----------br0----------eth0 | | | | | | 192.168.100.2/24| 192.168.100.1/24 |192.168.100.3/24 | | | | +-------------------+ | +------------------+ | | +-------------------------------------------------+ | +---------------------------------------------------------------------------------------------+ When I ping 192.168.100.3 from my UBUNTU-LXC, the source IP address is automatically changed to 192.168.100.2 by UBUNTU-VM. It's like having a NAT, whereas I really want my UBUNTU-LXC to talk with it own IP address. Is there any way to do this ? Edit : these info may be relevant : I am using KVM +libvirt to set up my VMs Here is how I create my interface in UBUNTU-VM : <interface type='bridge'> <mac address='52:54:00:cb:aa:74'/> <source bridge='br0'/> <model type='e1000'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x09' function='0x0'/> </interface>

  Read the article

• Error when starting qpidd as a service

  - by Sparks

  I have recently swapped from CENTOS 5 to FEDORA 17. Previously I have created my own init.d scripts successfully (albeit not for qpidd) however, in FEDORA I cannot get it to work. I have created the following script (called qpidd) in the init.d directory: #!/bin/bash # # /etc/rc.d/init.d/qpidd # # QPID/AMQP Broker scripts # # # chkconfig: 2345 20 80 # description: QPID/AMQP Broker service # processname: qpidd # pidfile: /var/lock/subsys/qpidd # Source function library. . /etc/init.d/functions SERVICENAME=qpidd start() { echo -n "Starting $SERVICENAME: " daemon qpidd -d & retval=$? touch /var/lock/subsys/$SERVICENAME return $retval } stop() { echo -n "Shutting down $SERVICENAME: " qpidd -q & retval=$? rm -f /var/lock/subsys/$SERVICENAME return $retval } case "$1" in start) start ;; stop) stop ;; status) status qpidd ;; restart) stop start ;; condrestart) [ -f /var/lock/subsys/<service> ] && restart || : ;; *) echo "Usage: $SERVICENAME {start|stop|status|restart" exit 1 ;; esac exit $? After this, I ran chkconfig --add qpidd, however, now when I run sudo service qpidd start I get the following message: Starting qpidd (via systemctl): Job failed. See system journal and 'systemctl status' for details. If I then run systemctl status qpidd I get the following message: Failed to issue method call: Unit name qpidd is not valid. I am now lost, I have search the web and Stack Overflow but cannot find anybody with similar problem, any help or direction to a website that can help would be much appreciated Sparks :)

  Read the article

• How to diagnose causes of oom-killer killing processes

  - by dunxd

  I have a small virtual private server running CentOS and www/mail/db, which has recently had a couple of incidents where the web server and ssh became unresponsive. Looking at the logs, I saw that oom-killer had killed these processes, possibly due to running out of memory and swap. Can anyone give me some pointers at how to diagnose what may have caused the most recent incident? Is it likely the first process killed? Where else should I be looking?

  Read the article

• High Availability Configuration using Heartbeat and Pacemaker

  - by pradeepchhetri

  I have the following setup: I have configured high availability between two load balancers (HAProxy) so that if HAProxy1 get down, the floating IP gets transferred to the other load balancer HAProxy2, hence all the clients will get the response from HAProxy2, which at the back-end is doing LB among the sme two webserver. This is for removing the single point of failure in case of only one HAProxy. Whenever I stops the hearbeat in HAProxy1, the floating IP goes to HAProxy2. But I want to configure such that whenever the process haproxy goes down, the floating IP should get assigned to HAProxy2. Can someone tell me how to implement it ?

  Read the article

• How do you set up Ubuntu to see Windows Network?

  - by Axeman

  I've tried the various tutorials and no success so far. I can connect to the router and from there to the internet, but I cannot see any network shares. I'm connecting through wlan0. I would prefer to keep the dynamic IP address if possible.

  Read the article

• Why create many partitions?

  - by ryeguy

  I have noticed that when installing Ubuntu some people create multiple partitions for directories. Like one for root, one for home, one for boot. What is the advantage to doing this over installing them all on one partition, assuming there is only one hard drive?

  Read the article

< Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >