Search Results

Search found 11955 results on 479 pages for 'non techie'.

Page 351/479 | < Previous Page | 347 348 349 350 351 352 353 354 355 356 357 358  | Next Page >

• How can I control disk numbering (enumeration) in Windows 7 Disk Management?

  - by tim11g

  A desktop system had two drives (Assigned C and D, which were enumerated in Disk Management as Disk 0 and Disk 1). A new SSD was added as the boot drive, after copying the C drive to the SSD. The SSD was connected to SATA 0 (master) port on the motherboard. The previous C Drive was moved to SATA 2 and is reformatted as a non-booting NTFS partition. The D drive remained on SATA 1. The system boots and everything seems fine. I was able to manually adjust the Drive Letters. However, the list in Disk Management is re-ordered. Disk 0 is the the previous Disk 2 (D Drive) on SATA 1, Disk 1 is the new Boot Drive (now C) on SATA 0, and Disk 2 is the former C Drive (now assigned E) on SATA 2. Does the Disk 0, 1, 2, designation mean anything? I would prefer to have them display in Disk Management as Drives C, D, and E from top to bottom. Is the Disk enumeration based on the SATA port or something else? (If it was based on SATA Port, they should be ordered C, D, E. Is there any way to re-order the Disk number assignments? What actually does determine the Disk number enumeration?

  Read the article

• Windows 8.1 - Won't boot (0xc000000f), bcdedit fails

  - by user3014097

  I’m pretty much stuck at this point. So, backstory: Windows was installed on one of the SSDs currently in my tower. I bought a new SSD to install Windows (8.1 64 bit) on. Windows installation went fine, booted up, and formatted the old SSD from within Windows (this seems to have been a mistake, but I didn’t realize that at the time). Despite formatting the old SSD, whenever I tried to boot I was told that there were 2 Windows installations. Apparently, when I formatted the old drive, not all of the partitions were removed. So, I booted up with the repair utility, went into cmd, and deleted the non-primary partitions on the old SSD (there were 2 – think they were system and recovery, although I’m forgetting now). Reboot – computer won’t boot. Getting the 0xc000000f “The boot selection failed because a required device is inaccessible” error. Troubleshooting so far: Automatic repair doesn’t fix anything (I’ve never had luck with it though) If I go to install a new version of Windows, the drives and partitions are all there. The SSD is functioning, I at least know that. I’ve essentially gone through this guide: https://neosmart.net/wiki/recovering-windows-bootloader/ Unfortunately, I’m not getting anywhere. I’m not even entirely sure how to describe the errors I’m getting, so I’ve just included pictures of every step (I can't actually post them though so I just included a photobucket link). http://s319.photobucket.com/user/DGalt11/library/Computer%20Issue Am I completely screwed here (i.e. reformat and reinstall?)? Thanks

  Read the article

• SSO "Portal"

  - by Clinton Blackmore

  Pursuant to my question on alleviating the password explosion, I've contacted some of the services to whom we are paying money to access their websites to ask if we could authenticate our own users, and some of them said yes and send me specs on how to do so. (One of the sites called such a system a page a "portal"; I've never heard the term used in quite that way.) It is simple enough that I am tempted to roll my own. The largest complication is that one site wants us to store a key for every user in our database (and I think the LDAP database makes sense) after their initial login. So, non-trivial, but doable. The nature of these sorts of tasks, I expect, is that if they start out small and simple, they don't end that way. There must be some software that addresses this that is readily extended, surely. In my searching, I've come across: SimpleSAMLphp JOSSO RubyCAS-Server Shibboleth Pubcookie OpenID [Wow, gee. I'd missed some of those in my previous searches! The wikipedia page on Central Authentication Services is useful, and the section on Alternatives to OpenID makes it look like there is a lot of choice.] Can anyone recommend any of these, or suggest ones to avoid? Internally, we are authenticating using Apple's Open Directory [ == OpenLDAP + Kerberos + Password Server (which, I believe, == SAML) ]. As far as extending/tweaking/advanced configuration of a system, I am able to program in Python, C++, can do some basic PHP, and may be able to remember some Java. Looks like I need to pick up Ruby at some point. Addendum: I would also like users to be able to change their passwords over the web (and for certain users to change passwords of other users).

  Read the article

• CDROM does not appear on desktop, MACOS 10.5.7

  - by Cheeso

  When I pop a CDROM into the drive of my Macbook Pro, It spins up, I hear it, but no icon appears on the desktop. (I think it's 10.5.7; actually not sure how to verify this on Mac, but I think I saw a 10.5.7 flash by somewhere). In the finder preferences, I have "Show these items on the Desktop" set to show HDs, External Disks, and CDs, DVDs, and ipods. All three of those are checked. I do see the internal HD on the desktop. In Disk utility I can see the CD/DVD hardware. It says "MATSHITA DVD-R UJ-857E...". From Disk Utility I can eject the drive. But in Finder, there is never a CD/DVD listed under "Devices". When I insert a disk, nothing happens, I cannot see it. I also cannot boot from bootable CDROMs by holding C down . Suggestions? I am not very experienced with Mac; I have used Windows for years. EDIT Two updates: I saw this article on support.apple.com, and modified the hostconfig appropriately. It did not have the AUTODISKMOUNT entry, so I added one, rebooted. Same behavior. It does not see the CDROM in Finder, does not mount it on desktop. I put an old manufactured CDROM into the drive, and voila! it showed up on the desktop. The CD that does not appear is a GNome Partition Editor Live CD, which I guess is based on debian. That CD boots in other (non-Mac) PCs. I want to use this to adjust the Bootcamp partition. Suggestions?

  Read the article

• Hardware doesn't work some times

  - by Ali

  I have an Asus n51vf laptop. I bought it not long time ago (less than a month) and installed Windows 7 on it. Since that it wasn't new when I bought it, I don't know, if the problem was occuring before re-installing Windows 7. There are two problems, that might (or might not) have something to do with each other: Problem The less annoying problem is that the screen flickers ONLY on YouTube when scrolling and/or pausing/playing the video or moving the curser over the video. The second more timeconsuming problem is that some of the hardware doesn't work when I turn up the computer. Then I have to reboot the computer and try again. Example: I turn on the computer, and the touchpad doesn't work - I then reboot and it works again. This has so far happened to the screen (leading to a black screen), the keyboard and the touchpad. More frequently the mouse. What have I tried to do so far? I tried reeinstalling the touchpad driver (Synaptic Touchpad driver from Asus Support Page) - didn't help at all. I even tried reinstalling the driver when the non-responding mouse on startup-problem occured (using the keyboard), but it asked me to reboot and didn't help at all. I also installed (and reinstalled) the graphics driver; it's a GeForce GT 130M. Now, the problem never occurs spontaneously - it only appears when booting my computer. I can even use the computer for heavy tasks (games, multiple programs running etc.) with no problem at all. I suspect, that the problem is in some booting mechanism that fails: Maybe the Windows driver loading? Motherboard problems?

  Read the article

• Adobe Acrobat Reader don't zoom out the page enough in "one page" mode

  - by mbaitoff

  I'm using Adobe Acrobat Reader version 9.4 under Debian Lenny. I'm experiencing a problem: when I push the "Show one page at a time" button, I expect the page to zoom such that pressing PgUp/PgDn would turn to the next/previous page. However, the zoom seems to be not enough - very thin bottom portion of the page doesn't fit inside the reader window, and pressing PgUp/PgDn gives the jitter of the same page, and I have to push twice to get to the next page. It is even worse in continuous page mode - a roll of pages begin to be non-synced with window boundaries, ending up with page break right in the middle of the view after several turns of the pages. This behaviour doesn't occur on windows version - I have a page properly zoomed in single/continuous modes, so that turning the pages is performed as page-at-once, as intended. How to make the Acrobat Reader fit the page to window properly? Thats how it looks before pressing PgDn (notice the bottom edge of the "paper" hidden beneath the bottom window edge): Thats how it looks after pressing PgDn (notice the "paper" bottom edge emerged from beneath the window edge, while the "paper" upper edge hides behind the upper window edge, showing that the document window size is not enough to contain the whole page):

  Read the article

• Shared files folder in Amazon Elastic Beanstalk environment

  - by por

  I'm working on a Drupal application, which is planned to be hosted in Amazon Elastic Beanstalk environment. Basically, Elastic Beanstalk enables the application to scale automatically by starting additional web server instances based on predefined rules. The shared database is running on an Amazon RDS instance, which all instances can access properly. The problem is the shared files folder (sites/default/files). We're using git as SCM, and with it we're able to deploy new versions by executing $ git aws.push. In the background Elastic Beanstalk automatically deletes ($ rm -rf) the current codebase from all servers running in the environment, and deploys the new version. The plan was to use S3 (s3fs) for shared files in the staging environment, and NFS in the production environment. We've managed to set up the environment to the extent where the shared files folder is mounted after a reboot properly. But... The Problem is that, in this setup, the deployment of new versions on running instances fail because $ rm -rf can't remove the mounted directory, and as result, the entire environment goes down and we need restart the environment, which isn't really an elegant solution. Question #1 is that what would be the proper way to manage shared files in this kind of deployment? Are you running such an environment? How did you solve the problem? By looking at Elastic Beanstalk Hostmanager code (Ruby) there seems be a way to hook our functionality (unmount if mounted in pre-deploy and mount in post-deploy) into Hostmanager (/opt/hostmanager/srv/lib/elasticbeanstalk/hostmanager/applications/phpapplication.rb) but the scripts defined in the file (i.e. /tmp/php_post_deploy_app.sh) don't seem to be working. That might be because our Ruby skills are non-existent. Question #2 is that did you manage to hook your functionality in Hostmanager in a portable way (i.e. by not changing the core Hostmanager files)?

  Read the article

• computer build for extreme tabbed browsing

  - by David Berger

  I'm interested in building or buying a task-specific computer for my brother. His requirements are ridiculously simple: the machine has to be able to wait in hundreds of web-based virtual waiting rooms at once and not crash. To be competitive, he needs to be able to enter the waiting rooms an dauto-refresh them faster. My question is, what priority do I give the different specs? My initial surmise is this: Connection speed (nothing to do with my build, but I kind of think this will be more beneficial than anything I build for him) Memory size -- I don't usually see firefox taking up more than a gig, even when heavily tabbed, but I think one gig for the operating system and two gigs for the browser are necessary. Processor speed -- I think the processor will affect performance, but even something out of date will do what he needs Memory speed/RAM bus -- I doubt this will matter much, but it seems just on this side of irrelevant. Everything else is a non-issue for him. Does this seem to stack up correctly? Also, since he's looking to stay on the cheaper side, and I might end up recommending a refurb to him, is there anything particularly egregious that Vista would do if it came pre-installed? If I build it myself, I'll give him linux, but if I have it shipped to him, I'm not sure I could walk him through the install process for linux, but I probably could walk him through the process to upgrade to Windows 7, if it were somehow worth it.

  Read the article

• Serving and caching content from Amazon S3 with Tomcat

  - by Rob

  Hi all, We're looking to serve a range of content using Amazon S3 as a store for the content and Tomcat to host the web application. The content is divided into free and paid for content. We intend to authenticate the users when they access the web application running in Tomcat. Based around their authentication we are able to tell if the user has access to paid for content or simply free stuff. So I envision the flow of a request being something like this: Authenticated request to Tomcat If user is "paid" user, display links to premium content Direct requests for paid content back through Tomcat to prevent direct access to it by non-paying users. Tomcat makes request to S3 through a web cache to keep our costs down Content is returned to user. As we have to pay for each request to S3, I'd ideally like to cache content locally to the Tomcat instance after it has been requested for the first time to keep costs to a minimum and to speed things up. I would also like to be able to invalidate this cache if we publish fresh content to S3. So to confirm my proposal: Client Request - Tomcat - Web Cache - S3 To invalidate the cache, I was thinking of using something like PubSubHubbub with the cache waiting for updates to the feed for content that it should invalidate. I'd appreciate some general feedback on this approach as I've no real experience of caching and I'm sure I've made some invalid assumptions. I'd also appreciate any recommendations for caching technologies. Thanks.

  Read the article

• Overheating Toshiba Satellite L300

  - by ldigas

  A coleague of mine's having trouble with his new Toshiba Satellite L300 ... I tool a kook at it, and indeed it's hot as hell. I couldn't hold my hand on it for too long. He says it also has a tendency to turn itself off (WinXP 32bit running) with no forewarning. Hasn't happened to me while I was using it, but that wasn't long anyways. The first guess was it was too dirty ... problem is it's new, came out of a package a quarter of a year ago. Kept in a clean environment (office). Looks clean. No dust in sight. Second guess is that the fan wasn't working properly, cause indeed it has intervals of working, and non working. But when I listen to it, it sounds like normal usage. I took a SpeedFan measurement, and it reports temp. up to 85 Celsius ... which is definitely too high. Anyone knows what else I could do to it ? It is under warranty and it will go to the service, but I thought if there is something we can do, as to avoid carrying it there / be without it for a week ...

  Read the article

• What is the difference between the Linux and Linux LVM partition type?

  - by ujjain

  Fdisk shows multiple partition types. What is the difference between choosing 83) Linux and 8e) Linux LVM? Choosing 83) Linux also works fine for using LVM, even creating a physical volume on /dev/sdb without a partition table works. Does picking a partition type in fdisk really matter? What is the difference in picking Linux or Linux LVM as partition type? [root@tst-01 ~]# fdisk /dev/sdb WARNING: DOS-compatible mode is deprecated. It's strongly recommended to switch off the mode (command 'c') and change display units to sectors (command 'u'). Command (m for help): l 0 Empty 24 NEC DOS 81 Minix / old Lin bf Solaris 1 FAT12 39 Plan 9 82 Linux swap / So c1 DRDOS/sec (FAT- 2 XENIX root 3c PartitionMagic 83 Linux c4 DRDOS/sec (FAT- 3 XENIX usr 40 Venix 80286 84 OS/2 hidden C: c6 DRDOS/sec (FAT- 4 FAT16 <32M 41 PPC PReP Boot 85 Linux extended c7 Syrinx 5 Extended 42 SFS 86 NTFS volume set da Non-FS data 6 FAT16 4d QNX4.x 87 NTFS volume set db CP/M / CTOS / . 7 HPFS/NTFS 4e QNX4.x 2nd part 88 Linux plaintext de Dell Utility 8 AIX 4f QNX4.x 3rd part 8e Linux LVM df BootIt 9 AIX bootable 50 OnTrack DM 93 Amoeba e1 DOS access a OS/2 Boot Manag 51 OnTrack DM6 Aux 94 Amoeba BBT e3 DOS R/O b W95 FAT32 52 CP/M 9f BSD/OS e4 SpeedStor c W95 FAT32 (LBA) 53 OnTrack DM6 Aux a0 IBM Thinkpad hi eb BeOS fs e W95 FAT16 (LBA) 54 OnTrackDM6 a5 FreeBSD ee GPT f W95 Ext'd (LBA) 55 EZ-Drive a6 OpenBSD ef EFI (FAT-12/16/ 10 OPUS 56 Golden Bow a7 NeXTSTEP f0 Linux/PA-RISC b 11 Hidden FAT12 5c Priam Edisk a8 Darwin UFS f1 SpeedStor 12 Compaq diagnost 61 SpeedStor a9 NetBSD f4 SpeedStor 14 Hidden FAT16 <3 63 GNU HURD or Sys ab Darwin boot f2 DOS secondary 16 Hidden FAT16 64 Novell Netware af HFS / HFS+ fb VMware VMFS 17 Hidden HPFS/NTF 65 Novell Netware b7 BSDI fs fc VMware VMKCORE 18 AST SmartSleep 70 DiskSecure Mult b8 BSDI swap fd Linux raid auto 1b Hidden W95 FAT3 75 PC/IX bb Boot Wizard hid fe LANstep 1c Hidden W95 FAT3 80 Old Minix be Solaris boot ff BBT 1e Hidden W95 FAT1 Command (m for help):

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

• Ubuntu 12.04 - HP ProLiant DL380 G4 - Load Maxes Out / Unresponsive

  - by Brian S

  Trying to post this question on here. I've posted it on the Ubuntu forums as well with no replies. Recently I upgraded an HP ProLiant DL380 G4 server from Ubuntu 10.04 server to Ubuntu 12.04 server. Upon doing so, the server will not - at random times - get to a load of 400+ and then become completely non-responsive. I use an SNMP graphing program (cacti) and the load steadily increases by about 10 every five minutes until it gets over 400 and the graphing stops. The graphs may not be accurate, but the CPU load averages about 3% before this happens - and right when the load starts increasing, it jumps to about 25% for 15 minutes and dramatically dips down to less than 1% (about 0.3%) until the graphing stops. I'm not able to open a SSH tunnel to the server to do anything. I've checked the /var/log/syslog and all logging stops at that time as well - with nothing else in there. The odd thing is - the server still responds to DNS queries for the zones it is authoritative on during this time - and at normal speed. Just not sure what the next step would be in order to find out what is going on - and how this issue can be corrected. The server cannot stay with Ubuntu 10.04 Server and needs to stay upgraded.

  Read the article

• Creating Active Directory on an EC2 box

  - by Chiggins

  So I have Active Directory set up on a Windows Server 2008 Amazon EC2 server. Its set up correctly I think, I never got any errors with it. Just to test that I got it all set up correctly, I have a Windows 7 Professional virtual machine set up on my network to join to AD. I set the VM to use the Active Directory box as its DNS server. I type in my domain to join it, but I get the following error: DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "ad.win.chigs.me": The query was for the SRV record for _ldap._tcp.dc._msdcs.ad.win.chigs.me The following domain controllers were identified by the query: ip-0af92ac4.ad.win.chigs.me However no domain controllers could be contacted. Common causes of this error include: - Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses. - Domain controllers registered in DNS are not connected to the network or are not running. It seems that I can talk to Active Directory, but when I'm trying to contact the Domain Controller, its giving a private IP to connect to, at least thats what I can make out of it. Here are some nslookup results. > win.chigs.me Server: ec2-184-73-35-150.compute-1.amazonaws.com Address: 184.73.35.150 Non-authoritative answer: Name: ec2-184-73-35-150.compute-1.amazonaws.com Address: 10.249.42.196 Aliases: win.chigs.me > ad.win.chigs.me Server: ec2-184-73-35-150.compute-1.amazonaws.com Address: 184.73.35.150 Name: ad.win.chigs.me Address: 10.249.42.196 win.chigs.me and ad.win.chigs.me are CNAME's pointing to my EC2 box. Any idea what I need to do so that I can join my virtual machine to the EC2 Active Directory set up I have? Thanks!

  Read the article

• Windows Server NTFS volume list file name encodings and any illegal file names

  - by benbradley

  I'm having to deal with a Windows Server (NTFS) file server and our backup application appears to be failing with certain files. According to this https://en.wikipedia.org/wiki/NTFS#Internals NTFS apparently supports file names encoded in UTF-16 but according to their support team, our backup application only supports UTF-8. I'd like to confirm whether this is actually the problem by seeing the file name encoding for myself. The files that are failing appear to be using plain English A-Z letters and other ASCII characters. No accents or non-English letters etc. I suppose even though the letters appear to be plain A-Z the file name could still be encoded in UTF-16. Does anyone know of a utility or script that can recursively go through all files in a directory and show the encoding of the file name? Then I could try renaming to UTF-8 to see if the backup can proceed. I'm not a Windows developer so can't write this up myself. Presumably the encoding of the file name should be stored in the FS somewhere and therefore it should be possible to expose this.

  Read the article

• Bypass proxy authentication [closed]

  - by Diego Queiroz

  My scenario: My network has a proxy that requires interative authentication. When I access any URL, an username and password is requested to enable navigation. I do have a valid username/password (this means I have permissions to access external content). I do not have access to the proxy server (any change to the proxy server is not an option). What I need: I need to bypass the interative authentication process and make it an automated authentication process. What I do NOT need/want: I do not need/want to hack the network. I do not need/want to access unauthorized content. In other words, I just need to find a way to "save" my password in the computer (security is not a problem) to allow application that does not support this kind of interative authentication to access the internet (like non-browser software that also uses HTTP port). My guess: My guess is to develop a new proxy server that will run in the local machine (eg, a proxy for the network proxy). This proxy server will access my network proxy, authenticate and forward the content. Of course this is a last resort. I prefer to not need to develop a proxy server. Does someone know other solution? (any operating system)

  Read the article

• Recommendations for hosting large videos

  - by Clinton Blackmore

  I recently created and put a 45-minute, 300 MB video file on my website and told a mailing list about it. Checking my site stats, I see that I've used 20% of my "unlimited" bandwidth for the month. As I want to be able to have several videos like this, clearly, I need to consider other options. The appeal to hosting files as my own site (aside from the supposedly unlimited disk space and bandwidth), is to be able to have control over the format, resolution, and quality of the video(s), as well as to ensure that it is clear that I'm the copyright holder (although the videos will be under a creative commons license). I find that for the screencasts I'm making, having a high resolution (say 3/4 of 1024 * 768) really makes seeing what is going on on the screen easier. It is also always a plus to not have the experience marred by advertisements. One more wrench to throw in is that while the videos are non-commercial, they do promote a club, and it seems that that falls afoul of some terms of services (especially for free services; while free is very nice, I will certainly consider putting up some money.) What recommendations do you have for (fairly) long, high-resolution videos? Should I look in depth at sites like YouTube and Vimeo, should I be considering a filesharing site [I have no qualms with someone downloading the entire video first -- I wouldn't want to watch 45 minutes in my browser!], hosting files with Bittorent (ugh -- I think that'd reduce my audience), or should I be looking into other web hosts (and if so, who?)

  Read the article

• eAccelerator Issue - Cache Directory Empty.

  - by Tom

  Hi all, Hoping someone can give me a hand with this. I've recently installated eAccelerator 0.9.6.1 - On a CentOS LAMP server. Had it working fine, using the /tmp/accelerator as the cache directory. php.ini set up: zend_extension="/usr/local/lib/php/extensions/no-debug-non-zts-20060613/eaccelerator.so" eaccelerator.shm_size="200" eaccelerator.cache_dir="/var/cache/eaccelerator" eaccelerator.enable="1" eaccelerator.optimizer="1" eaccelerator.check_mtime="1" eaccelerator.debug="0" eaccelerator.filter="" eaccelerator.shm_max="0" eaccelerator.shm_ttl="3600" eaccelerator.shm_prune_period="180" eaccelerator.shm_only="1" eaccelerator.compress="1" eaccelerator.compress_level="9" php -v output: PHP 5.2.12 (cli) (built: Feb 3 2010 00:34:28) Copyright (c) 1997-2009 The PHP Group Zend Engine v2.2.0, Copyright (c) 1998-2009 Zend Technologies with eAccelerator v0.9.6.1, Copyright (c) 2004-2010 eAccelerator, by eAccelerator with the ionCube PHP Loader v3.3.20, Copyright (c) 2002-2010, by ionCube Ltd. I had to remove the cache directory as I was testing something. Remade it, re-set permissions and found that eAccelerator was no longer creating cache files within the folder. I thought it might be down to ownership rights on the folder so chown'd it apache.apache and this made no difference. I recreated the directory in /var/cache instead and editted php.ini to point to the new cache dir location, chmod'd, chown'd etc. and still eAccelerator is not creating any of the cache files in the directory (just empty). Could someone suggest what I might be doing incorrectly here. I've read through numerous pages to try and troubleshoot the issue to no avail. Any help appreciated.

  Read the article

• preformance wise htaccess

  - by purpler

  hese's the my htaccess template, i wonder if anything could be added to increase website performance.. # Defaults AddDefaultCharset UTF-8 DefaultLanguage en-US ServerSignature Off FileETag None Header unset ETag Options -MultiViews #Options All -Indexes # Force the latest IE version or ChromeFrame <IfModule mod_setenvif.c> <IfModule mod_headers.c> BrowserMatch MSIE ie Header set X-UA-Compatible "IE=Edge,chrome=1" env=ie </IfModule> </IfModule> # Proxy X-UA Setup <IfModule mod_headers.c> Header append Vary User-Agent </IfModule> #Rewrites Options +FollowSymlinks RewriteEngine On RewriteBase / # Redirect to non-WWW RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} ^www\.(.+)$ [NC] RewriteRule ^(.*)$ http://%1/$1 [R=301,L] # Redirect to WWW RewriteCond %{HTTP_HOST} ^domain.com RewriteRule (.*) http://www.domain.com/$1 [R=301,L] # Redirect index to root RewriteRule ^(.*)index\.(php|html)$ /$1 [R=301,L] # Caching ExpiresActive On ExpiresDefault A0 Header set Cache-Control "public" # 1 Year Long Cache <FilesMatch "\.(flv|fla|ico|pdf|avi|mov|ppt|doc|mp3|wmv|wav|png|jpg|jpeg|gif|swf|js|css|ttf|eot|woff|svg|svgz)$"> ExpiresDefault A31622400 </FilesMatch> # Proxy Caching <FilesMatch "\.(css|js|png)$"> ExpiresDefault A31622400 Header set Cache-Control "private" </FilesMatch> # Protect against DOS attacks by limiting file upload size LimitRequestBody 10240000 # Proper SVG serving AddType image/svg+xml svg svgz AddEncoding gzip svgz # GZip Compression <IfModule mod_deflate.c> <FilesMatch "\.(php|html|css|js|xml|txt|ttf|otf|eot|svg)$" > SetOutputFilter DEFLATE </FilesMatch> </IfModule> # Error page ErrorDocument 404 /404.html # Deny access to sensitive files <FilesMatch "\.(htaccess|ini|log|psd)$"> Order Allow,Deny Deny from all </FilesMatch>

  Read the article

• How to access Windows Server 2008 R2 file shares from a different subnet

  - by Lloyd Cotten

  We have a couple of severs that used to be Windows Server 2003 that we recently upgraded to Windows Server 2008 R2. A couple of details to set the situation up: We wiped the OS and re-installed. These servers are on one subnet (172.16.x.x) and we are trying to access some file shares on them from another subnet (10.34.x.x). Firewall is disabled on these servers. Trying to access with UNC "\172.16.x.x\sharename" and net use \172.16.x.x However, we're having problems doing this. We are getting "The network path was not found". Here's some of the things we've tried so far and the result: Tried accessing the share from other (non-2008) servers on the same subnet... Success! Ping servers from different subnet... Success! Telnet connection into port 139 from different subnet... Success! Took a scan through Local Security Policies to see if something obvious needed to be enabled / disabled / configured... Fail I'm not sure where to look next. I know that the router between the two subnets is locked down pretty good, but this did work for our 2003 servers. Has anything changed in the way of ports used for UNC / file share access in 2008? Maybe I'm missing some security policy setting? Hoping somebody can take pity on a poor programming guy that can't figure out something really simple. :-) Thanks!

  Read the article

• Nginx: Serve static files out of a given directory - one level too deep

  - by Joe J

  I'm pretty new to nginx configs. I'm having some difficulty with a pretty basic problem. I'd like to host some static files at /doc (index.html, some images, etc). The files are located in a directory called /sites/mysite/proj/doc/. The problem is, is that with the nginx config below, nginx tries to look for a directory called "/sites/mysite/proj/doc/doc". Perhaps this can be fixed by setting the root to /sites/mysite/proj/, but I don't want to potentially expose other (non-static) assets in the proj/ directory. And for various reasons, I can't really move the doc/ directory from where it is. I think there is a way to use a Rewrite rule to solve this situation, but I don't really understand all the parts, so having some difficulty formulating the rule. rewrite ^/doc/(.*)$ /$1 permanent; I've also included a working example of hosting files out of a /sites/mysite/htdocs/static/ directory. > vim locations.conf location /static { root /sites/mysite/htdocs/; access_log off; autoindex on; } location /doc { root /sites/mysite/proj/doc/; access_log on; autoindex on; } 2011/11/19 23:49:00 [error] 2314#0: *42 open() "/sites/mysite/proj/doc/doc" failed (2: No such file or directory), client: 100.100.100.100, server: , request: "GET /doc HTTP/1.1", host: "myhost.com" Does anyone have any ideas how I might go about serving this static content? Any help is much appreciated. Thanks, Joe

  Read the article

• Virtual Fileserver

  - by Sergei

  Hi, We are planning to move our production servers to the datacenter and virtualize remaining servers in the process.Datacenter will have HP blades with vSphere on top.Currentliy we are using Celerra NS20 as fileserver.Since datacenter is using HP kit and EVA 4400 as SAN, we cannot have Celerra there, as EMC supoprt for Celerra does not work for non EMC array. I have searched for possible options and one of them was to have HP NAS blade X3800sb instead of Celerra.However this seems like overkill for me.We are only using Celerra for about 100 users and 50 servers and I think having X3800sb could be waste of resources. The other option would be to have a virtual fileserver as a part of vmware environment in datacenter.We only need CIFS to be provided.The only option I can think of is Windows Storage server.We had a bad expirience with Windows servers used as fileservers ( memory leaks one thing) in the past and this was one of the reasons we moved to Celerra. What are the other options?We need something as reliable as Celerra with as many options as possible.For example , Celerra has per folder quotas, deduplication, dynamic volume allocation, automatic failover, VTLU, replication. Also we would need to replicate NAS data to the failover site.We could use block level replication , SAN-to-SAN, but this would mean wasted bandwidth, as we need only subset of folders to be replicated.We used CA XSoft for windows servers in the past and Celerra has option for Celerra replication. Thank you very much in advance, Please ask me if I missed any details!

  Read the article

• Windows Key is shutting my PC with Windows 7 down when pressed

  - by jasondavis

  I am having a really annoying problem lately with my Windows 7 PC. The problem, is all of a sudden, just within the last day or 2, anytime I hit the WIN (Windows keyboard key) instead of popping up the start menu, the system shuts down all my programs and trys to shut down, the only reason it doesn't suceed is because one of the programs I will have running will have an un-saved document, so it will ask me if I want to save the document before shutting down, I then can hit cancel and it halts the process. I do not remember installing anything and programs from from around the time it started doing this, maybe 2-3 days ago. I have gone through and searched Google for every Process running in the taskmanager to see which processes were REQUIRED for Windows to run, I then closed eveything down and killed all the non-essential Processes and the result was this... The reason you see notepad.exe is because I had it open with an unsaved document to keep the system from shutting down, I then tried hitting the win key after I shut each process down, after everything was shut to just show the above, it still tries to shut my system down, this is driving me insane, please help I am at a lost. I am about to see if I can try a different keyboard just encase it is some malfunction on the keyboard. The reason I need to access the WIN key or would like to is because I have Win + v set up to work with a special clipboard manager I believe it is called ClipX

  Read the article

• Cannot remove storage account because of lease, but I already deleted the server [closed]

  - by djechelon

  I recently created a temporary virtual server on Azure. Then I deleted it. I wanted to delete the storage account associated with it because I didn't need it any more. The problem is that the VHD file is still associated to a non-existing virtual machine!! If I try to delete the VHD from Virtual Machines\Disks I get the Delete button greyed and the table tells me it's still associated with the old VM. If I go to storage administration and try to delete the blob from vhds/ directory I get there is an active lease. I've read on Azure forums that, in these case, one should try to force releasing the lease from the blob. I followed their instructions and downloaded their script, but running it failed. The script detected that the disk is associated to a Virtual Machine and can't be deleted. The problem is that I'm 1000000% sure that I already deleted the VM. In fact, I currently only have a single VM that has its own HD and is up and running fine! What can I do to delete that storage account that is probably sucking money from my pocket?

  Read the article

• can't connect to vsftpd from outside network

  - by rick

  i know this has been asked many times before, but nothing seems to resolve my issue. i have vsftpd running on ubuntu 10.04. i can connect with ftp localhost on the machine. i can connect from another machine in my network. i just cannot connect from outside. the machine is behind an airport extreme managed by airport utility on a mac. 21 is open as per nmap: macmini:~$ nmap localhost Starting Nmap 5.21 ( http://nmap.org ) at 2011-04-10 23:49 EDT Nmap scan report for localhost (127.0.0.1) Host is up (0.00045s latency). Hostname localhost resolves to 2 IPs. Only scanned 127.0.0.1 rDNS record for 127.0.0.1: localhost.localdomain Not shown: 997 closed ports PORT STATE SERVICE 21/tcp open ftp 22/tcp open ssh 631/tcp open ipp netstat says 21 is listening: macmini:~$ netstat -lep --tcp | grep ftp (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) tcp 0 0 *:ftp *:* LISTEN iptables: macmini:~$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination when i try to connect from my external IP (or a dyndns name which resolves there) it times out. ("control connection timed out") as i know very little about networking, i feel like something may jump out as clearly wrong?

  Read the article

< Previous Page | 347 348 349 350 351 352 353 354 355 356 357 358  | Next Page >