Search Results

Search found 11707 results on 469 pages for 'boot failure'.

Page 355/469 | < Previous Page | 351 352 353 354 355 356 357 358 359 360 361 362  | Next Page >

• X locks up with konqueror on comics.com

  - by retracile

  If I browse to comics.com using konqueror under KDE on Fedora 11, X will, after a delay, lock up. The mouse will move, but no keyboard input is recognized, and the screen does not react to the mouse passing over objects on screen. I am able to ssh into the machine and issue shutdown -r now and have that work. The machine is a Dell XPS M1330 with Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c), and Fedora 11 is fully updated. Visiting the same site in Firefox does not cause a lockup. I am booting with nomodeset since it won't boot into X otherwise. I tried the other two accel options: EXA (still locks up) and XAA (X won't start). Any suggestions on how I can debug this? bugzilla

  Read the article

• Nexus One USB freezes Vista SP2 Quad Core

  - by user25479

  My Nexus One (N1) will occasionally freeze my Vista 32bit SP2 Quad Core 2.4GHz during POST. MB is ASUS P5N-E SLI with 4GB of RAM. The PC will be booting and when I connect the N1 via USB, the boot sequence will freeze, then continue once I unplug the N1 USB link. It happens whether the N1 is in USB debugging mode and when it is not. I'm not sure whether this is an N1 hw/fw issue, system interaction with my PC, or a result of my N1 development environment (I'm using the Eclipse Galileo IDE for Java Developers, primarily compiling to API Level 7. Eclipse has also occasionally frozen although I haven't established N1 USB cause-and-effect on that issue). Is anyone else experiencing these symptom?

  Read the article

• Retrieving a specific value from “df -h” using shell

  - by diegodias

  When I use df -h, I get the following output: Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 59G 2.2G 54G 4% / /dev/sda1 122M 38M 78M 33% /boot tmpfs 1.1G 0 1.1G 0% /dev/shm 10.10.0.105:/somepath 11T 8.4T 2.1T 81% /storage4 10.11.0.101:/somepath 15T 8.9T 5.9T 61% /storage1 /dev/mapper/patha 5.0T 255G 4.8T 5% /storage5_vol0 /dev/mapper/pathb 5.0T 195G 4.9T 4% /storage5_vol1 /dev/mapper/pathc 5.0T 608G 4.5T 12% /storage5_vol2 I want to write a script that gets the value of Avail column on a specific storage. I used to use df -k /storage_name | tail -1 | awk '{print $3}' But the FileSystem column can have a value or not .. which would change the variable of my script from $3 to $4. How can I get the Avail on a single command line even if there are no values on the previous columns?

  Read the article

• Cloning Win 7 installation from MBR to GPR drive and make it bootable

  - by Nelluk

  I've seen threads on similar topics - such as this one - but the answers never seem to solve how to make it bootable. I have Win 7 64-bit on a PC installed on a 2tb MBR volume. The motherboard is UEFI compatible. I just installed a secondary internal 3TB drive which will be partitioned as GPT. Is there a relatively easy way to clone my installation over to the new drive and have that drive be bootable? I have used EaseUS Partition Master to clone the C volume to the D volume, but that would not boot and I assume the issue is that one is MBR and one is GPT. Is there a process to do this?

  Read the article

• OSX Menu bar doesn't appear til opening an application

  - by gms8994

  When I boot my MBP, the menu bar doesn't appear. When I open Mail.app or Safari, the menu bar appears. I've searched for a bit, and nothing seems to talk about this. Is there a way to fix this? UPDATE From the Console logs: 3/29/12 7:05:10.037 AM com.apple.launchctl.Aqua: load: option requires an argument -- D 3/29/12 7:05:10.037 AM com.apple.launchctl.Aqua: usage: launchctl load [-wF] [-D <user|local|network|system|all>] paths... 3/29/12 7:05:10.100 AM com.apple.launchd.peruser.501: (com.apple.launchctl.Aqua[153]) Exited with code: 1

  Read the article

• Major Issue with Asus M4A78T-E Bios

  - by user114721

  I am having major issues with my bios and I have tried three different forums in hopes that there is someone out there that can help me.... The issue is that every single time I turn off my computer, when I turn it back on the bios resets and tries to boot from a floppy drive....first problem is I dont have a floppy drive and secondly it does not read my HDD.... I tried everything to fix this...I tried replacing the cmos battery, I tried replacing the sata cable, and I tried a different sata port....none of these things seem to be working. Now the messed up part about all of this is that i am on my computer right now....If I take the battery out and put it back in and setup the bios again manually I am able to get into my computer...but this is NOT normal... Why is my bios resetting constantly when I power down my computer? Please assist me I need my computer for business

  Read the article

• two operating systems sharing their file systems with eachother (Windows and Linux)

  - by John Kube

  I have two operating systems installed on my notebook computer, Windows Vista and Ubuntu Linux. When I boot up, I'm presented with a bootloader which allows me to choose which one I want to load. I'm interested in sharing each operating system's file system with the other, such that I could access my Windows files from Linux and vice-versa. Is this possible, and if so how would one go about setting it up? Feel free to just post a link to an existing solution if there is one. I would Google for this myself, but I don't even know what to search for, as I don't know what this is called.

  Read the article

• Computer POST's and draws the BIOS screens very slowly - Motherboard issue?

  - by Ssvarc

  I have a desktop that refuses to boot into Windows. I used Hitachi DFT and the HD came back OK. I then used Memtest86+ and it took hours for the test to run. After 8+ hours it was up to test number 6. I aborted and ran Memtest86. It ran at basically the same speed. I aborted and went to look at the BIOS settings. The computer is running slow at POST. It takes a long time for the keyboard to be recognized, etc. The BIOS settings takes time to be (slowly) drawn on the screen. What could be causing such behavior? EDIT: I gave back the computer a while back without ever discovering the cause so I'm closing the question.

  Read the article

• How can I free up disk space in my Ubuntu Hardy Heron install?

  - by rvs

  I'd like to make some room on /dev/sda1 without necessarily having to remove a whole bunch of applications (I've already gone through and deleted all frivolous apps). This is the state of /dev/sda1 currently: Dir: / Type: ext3 Total: 9.4GiB Free: 488.6MiB Available: 0bytes Used: 8.9GiB EDIT added du output from comments below: 769068 /var/lib/mysql 351208 /usr/lib 297060 /usr/local/bin/eclipse/plugins 184124 /usr/bin 175924 /usr/lib/openoffice/program 143940 /usr/local/bin/eclipsePHP/plugins 92520 /boot 81200 /opt/android-sdk-linux/add-ons/google_apis-6_r01/images 79964 /opt That's funny, because the tables in /var/lib/mysql are the reason that I ran out in the first place. But I need them, and room for many more possibly large db's.

  Read the article

• What are "Missing thread recordng" erros when running fsck -fy?

  - by ohho

  There is some error reported when I run Disk Utility and verify the root volume on my OS X MacBook. So I boot and CMD-S into the shell mode and run /sbin/fsck -fy. Errors are like: ** Checking catalog file. Missing thread record (id = ...) In correct number of thread records ** Checking catalog hierarchy. Invalid volume file count (It should be ... instead of ...) ** Repairing Volume Missing directory record (id = ...) I'd like to know what is the cause of the above errors? Hopefully I will be more careful in the future to prevent them from happening again. p.s. I am using a SSD and so I assume mechanical hard disk error is less likely. Thanks!

  Read the article

• MediaShield RAID 5 is showing up as 760GB when the actual size is 2.7TB

  - by Ilya Volodin

  I just finished setting up Windows 2003 Server on my new server. And I started setting up a RAID 5 for it. I have 4x1TB Hard Drives. From MediaSheild RAID Utility (at boot time) the RAID size is displayed as 2.7TB. Linux also shows it as 2.7TB. However, in Windows, everything (including Windows Disk Management as well as Windows based MediaShield utility) is reporting only 760Gb. I already tried converting partitioning table to GUID from MBR, because I read somewhere that Windows can only handle up to 2TB MBR tables, that didn't help much. Tried searching for partitioning utilities that I could use, but couldn't find anything free. Formatted the disk as NTFS partition from within Linux, it stop showing in Windows all together, even MediaShield windows utility isn't showing at anymore. Windows is installed on a separate 500Gb hard drive, that's setup not to support RAID. Any ideas?

  Read the article

• Sonicwall settings for Polycom TFTP

  - by Michael Glenn

  I'm switching our VoIP phones (Polycom 301s and 501s) to our data network. They were previously segmented to their own network. This means disabling the DHCP on the Trixbox (Asterisk) server and configuring the Sonicwall TZ 210 DHCP to indicate that Trixbox is the TFTP server. The Polycom phones are stating "could not contact boot server". All phones are configured to TFTP and were confirmed working when previously using the Trixbox server for DHCP. Trixbox DHCP is now turned off. I've configured options 66(as String), 128(as IP) and 150(as IP) in DHCP and added them to a TFTP Option Group. I've enabled "Allow BOOTP Clients to use Range" for the Dynamic IP range and assigned the Option Group TFTP as the DHCP Generic Option Group. Any idea what I'm missing? Is there a separate tool to inspect the DHCP response to compare Trixbox to the Sonicwall?

  Read the article

• Revert "Deny" permissions in Windows 7

  - by saurabhj

  I made a very dumb mistake and I am hoping there is a way to fix this without having to boot in through a Linux Live CD and extracting the data. My user login to my Windows 7 system is: John John is part of the Administrator's group. I have a folder called "C:\Users\John" I tried to make this folder accessible to ONLY John (and deny from all other Administrators) by going to the Folder, Right Click Secturity tab and then selecting all the checkboxes under "Deny" while having selected the "Administrators" group. As a result, I cannot access this folder from any of the accounts: "John" and "Administrator" as both of them belong to the Administrators groupd and deny permissions out-weigh the "Allow Permissions" Is there any way I could revert this back? Thanks a million!

  Read the article

• ignore ipv6 router advertisements for static addresses with bonded interfaces

  - by boran

  I need to attribute static IPv6 addresses (not use autoconfigured addresses, and ignore router advertisements). This can be done as follows for a standard interface like eth0 iface eth0 inet6 static address myprefix:mysubnet::myip gateway myprefix:mysubnet::mygatewayip netmask 64 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.autoconf=0 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.accept_ra=0 However, how can this be done for bonded interfaces? using the "all" interface does not work. Systems is Ubuntu 10.04, 2.6.24-24-server. If one uses the above sysctl command for the bond0, the networking hangs on boot, because /proc/sys/net/ipv6/conf/bond0 does not yet exist and cannot be written to. One the system has booted /proc/sys/net/ipv6/conf/bond0 exist, so one solution after booting is to add the following to /etc/rc.local: /sbin/sysctl -q -w net.ipv6.conf.bond0.autoconf=0 /sbin/sysctl -q -w net.ipv6.conf.bond0.accept_ra=0 /etc/init.d/networking restart and this has the desired effect, the autoconfig v6 address disappears. Seems like a bit of a hack though, are there better solutions?

  Read the article

• Expanding Files 0%, error 0x80070017 Windows 7 x64 RTM

  - by Liam

  I have downloaded Windows 7 x64 from MSDN. I have checked the hash of the file and it is correct. I have them made a bootble USB stick (http://kmwoley.com/blog/?p=345 (had to use my vista bootsect.exe as running 32bit at the moment). When I boot from the USB it fails when expanding the file. It stays on 0% and fails after around 90 seconds. The error is 0x80070017. As the hash is correct and I am using USB I guess it could be a hardware problems. Any advice how to get Windows 7 installed? The machine is a Dell Studio Slim.

  Read the article

• Compiling the Linux kernel, how much size is needed?

  - by ant2009

  I have downloaded the newest most stable Linux kernel, 2.6.33.2. I thought I would test this using VirtualBox. So I create a dynamically sized harddisk of 4 GB. And installed CentOS 5.3 with just the minimum packages. I setup the make menuconfig with just the default settings. After that I ran make and got the following error: net/bluetooth/hci_sysfs.o: final close failed: No space left on device make[2]: *** [net/bluetooth/hci_sysfs.o] Error 1 make[1]: *** [net/bluetooth] Error 2 make: *** [net] Error 2 The amount of space I have left is: # df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 3.3G 3.3G 0 100% / /dev/hda1 99M 12M 82M 13% /boot tmpfs 125M 0 125M 0% /dev/shm My virtual size is 4 GB, but the actual size is 3.5 GB. $ ls -hl total 7.5G -rw-------. 1 root root 3.5G 2010-04-13 14:08 LFS.vdi How much size should I give when compiling and installing a Linux kernel? Are there any guidelines to follow when doing this? This is my first time, so just experimenting with this.

  Read the article

• Is there a "Run Level Configurator" for Windows XP?

  - by djangofan

  I have been having trouble with something causing my Windows XP system to take 6-8 minutes to startup from a cold boot. Something is happening during startup that is causing the system to crawl. I have a lot of Linux experience , especially configuring run levels so that some programs start before others do. I also know how to do that on Windows XP but its really complex, and with 50 services I'd have to keep a giant spreadsheet to keep it all organized. Is there such a thing as a Windows XP Tool that "emulates" the Linux run-level editors that I can use to control the order than services start on my system?

  Read the article

• asus eee pc 1018p os installation

  - by cornerback84

  My friend has an asus eee pc 1018p. It has no cd/dvd drive (neither do he have a usb cd/dvd drive). The OS wasn't working fine, so we decided to restore the system using the provided OS backup from HD. But midway to installation it was interrupted and the computer was restarted (not h/w or s/w issue but we did it). Now we cannot run the backup and we also tried to install windows 7 through USB, but as soon as we start to install the OS, it says that some device driver is missing. It turns out that the OS needs usb device driver to continue. It has USB 3.0 maybe thats why the OS needs the driver. I tried disabling 3.0 and enabling 2.0 but then it does not boot from USB drive for some reason. We are stuck with this. The backup doesn't runs and when booting from USB it says that it needs device driver. Anyone has any idea what we should do?

  Read the article

• What should I know before I set up RAID 6 on Linux?

  - by Dan Ellis

  I just ordered five 1TB drives to install as a RAID 6 array in a Linux server (keeping the existing 1TB drive as a boot disk). I want to use Linux MD for RAID rather than a RAID card, to avoid lock-in. The intended use is for storing filesystems for Xen development environments and an AFP server for iPhoto/Aperture/Lightroom. What things should I know before I set it up? For example, what would be a good choice of filesystem, and what chunk size should I use?

  Read the article

• Windows 2008 R2: can't extend C drive, mystery partitions

  - by wfaulk

  I have a Windows 2008 R2 server running under VMware ESX 4.0.0. I have reallocated disk space to it in order to extend the C drive, but Disk Management has "Extend Volume" greyed out. DISKPART shows more partitions than Disk Management shows, including one after the volume I'm trying to extend, which would explain why Disk Management isn't allowing the extension. Disk Management shows: System Reserved / 100MB NTFS / Healthy (System) (C:) / 39.39 GB NTFS / Healthy (Boot, Page File, Crash Dump) 10.00 GB / Unallocated DISKPART shows: Partition 1 Dynamic Data 992 KB 31 KB Partition 2 Dynamic Data 100 MB 1024 KB Partition 3 Dynamic Data 39 GB 101 MB Partition 4 Dynamic Data 1024 KB 39 GB My question at this point is: what the heck are partitions 1 and 4, where did they come from, why doesn't Disk Management show them, and, most importantly, can I delete partition 4 in order to extend partition 3?

  Read the article

• partitioning problems

  - by Remus Rigo

  I had on my laptop a dual system (Ubuntu 11.04 and Windows 7) and someway the partitions messed-up. Windows stopped from booting, I just got a blinking cursor, but Ubuntu worked fine. I tried to fix the windows boot (fixmbr, fixboot, bootsect /nt60 C:/....) but now grub was overwritten and I have no OS. Finally I formatted the hdd (low format), installed Windows, partition hdd with paragon partition manager and now I want to install Ubuntu, but Ubuntu sees an empty hdd, weird, can anyone tell me what can I do? EDIT: I have created: partition 1: 100MB ntfs - windows reserved (drive B) partition 2: 50GB ntfs win 7 (drive C) partition 3: 50GB ext3 linux partition 4: 'the rest' ntfs for data (drive E) (the swap i will create after)

  Read the article

• Windows 7 - Runs in safe mode, crashes in "normal" mode

  - by JonHopkins

  A couple of days ago I came back from a meeting to find my laptop had locked up. Power lights still on but the screen was blank (by which I mean black, though still "backlit" so not dead). Didn't respond to anything. I rebooted and it powered up fine and I got to the login screen. I logged in and it seemed to be going fine for about 30 seconds (gmail notifier and pidgin popped up) then the same thing happened - black screen. If I boot into Safe Mode it's all fine, no problems. I've tried removing everything from the startup folders (All users and my login), everything from the Run section of the registry (Local Machine and my login) and I've disabled every service which doesn't run in Safe Mode (assuming anything running in safe mode is OK) but the problem still exists. I've scanned the memory for errors (all fine). Any thoughts on what else I could try?

  Read the article

• Problems enabling BitLocker on Windows 7 enterprise

  - by ericl42

  I had BitLocker turned on originally when I loaded the computer but had to turn it off to do some testing. I recently tried to turn it back on and I continue to get the following error: Blockquote A required TPM measurement is missing. If there is a bootable CD or DVD in your computer, remove it, restart the computer, and turn on BitLocker again. If the problem persists, ensure the master boot record is up to date. Blockquote I have verified that there is nothing in the DVD tray and that the laptop is not docked. I have also verified that TPM is running and I have no problems enabling BitLocker on a flash drive. I think it's a problem with my MBR since I am dual booting into Fedora as well but I am not sure how to fix it. (even though it did work a few months ago while I was also dual booted) Thank you for the help.

  Read the article

• White Screen of Death

  - by cust0s

  The other night I updated my iTunes to the latest version (through Software Update) when I came to turn on my computer I was greeted with the dreaded white screen of death. I use an early 2008 iMac 24". I've tried the basic things, unplugging/turning off accessories, trying to boot from the install disk, reseting pram, etc, etc. Still no luck and no change what-so-ever. All I've been able to ascertain that my keyboard still works (by ejecting). I should point out that I did recently replace my Hard drive with a Western Digital Black 500GB (though the computer is well out of warrenty) and I'm a little concerned that the problem could be the screen.

  Read the article

• EFI Partition Types

  - by Will

  Another employee was working with a mounted VHD and was using diskpart on it and I'm not sure if he messed something up or not. I think it's fine but I wanted to double check. We have a Windows 2008 x64 machine that boots with EFI because of the large disks in the system. What should the different labels be within Disk Manager for this system? Here is what is currently set: 200 MB Partition - EFI System Partition C Partition - Boot, Page File, Crash Dump There should not be an active partition under EFI, correct? Also, is there supposed to be a "System" label in addition to "EFI System Partition"?

  Read the article

< Previous Page | 351 352 353 354 355 356 357 358 359 360 361 362  | Next Page >