Search Results

Search found 12144 results on 486 pages for 'non pae'.

Page 356/486 | < Previous Page | 352 353 354 355 356 357 358 359 360 361 362 363  | Next Page >

• Move an existing RAID 5 array from Ubuntu to Gentoo

  - by Cocoabean

  I have a 64-bit Ubuntu machine with a 4-disk RAID 5 using software raid (md). I've been able to boot an Ubuntu LiveCD and recognize the array with a simple mdadm -A /dev/md0. It was easy to mount after that and nothing had to rebuild. I'm installing Gentoo on this box now (multi-boot, non-RAID root partition) and I have md auto-detect turned on in the kernel. When I boot Gentoo I get: "invalid superblock magic on sdd" for each of the drives in the array. I boot back to Ubuntu and they mount no problem. I tried copying the mdadm.conf that works in Ubuntu to Gentoo, and then ran mdadm -A /dev/md0 but it reports that there is no array named md0. I don't want to lose data (obviously) and I don't want to have to let the RAID rebuild every time I switch between OSes. Any help is appreciated. Both are using mdadm 3.1.4 Both are running 64-bit kernels. mdadm -D /dev/md0 from Ubuntu yields: http://pastebin.com/5gj2QNkV UPDATE: After rebooting I noticed that it still complains about invalid blocks, but cat /proc/mdstat shows an inactive /dev/md127 with the same disks as my raid. I want to mount it but I don't want to get stuck waiting for a rebuild or destroying it inadvertently. mdadm -D /dev/md127 Here is pastebin of mdadm -D /dev/md127 on gentoo: http://pastebin.com/gDCWn0Rn UPDATE II: dmesg output about 'invalid raid superblocks' http://paste.ubuntu.com/885471/ fdisk -l from Ubuntu, /dev/md0 does not have any partitions but I do have it mounted and accessible: http://paste.ubuntu.com/885475/

  Read the article

• Conky starts above windows in Ubuntu Maverick

  - by DesertIvy

  Hey guys, I did not run into this problem until I upgraded my Ubuntu box to Maverick Meerkat (10.10). Basically, whenever I start my computer, conky runs as expected, except it gets drawn over any windows that I load (see screenshot). To fix this for a single session, I simply restart conky by running killall conky; conky in a terminal. Conky gets re-drawn below active windows (namely, only appearing on my desktop), and does not have the border/drop-shadow, but I have to do this every time I start a new session. Is there a simple way to fix this? I have a small shell script that I run on startup, but it does not seem to solve the problem. #!/bin/bash sleep 10 && conky; sleep 5 && killall conky; conky; Below is the non-text part of my .conkyrc file. # Conky settings # background yes update_interval 1 cpu_avg_samples 2 net_avg_samples 2 override_utf8_locale yes double_buffer yes no_buffers yes text_buffer_size 2048 #imlib_cache_size 0 temperature_unit fahrenheit # Window specifications # own_window yes own_window_type override own_window_transparent yes own_window_hints undecorate,sticky,skip_taskbar,skip_pager,below border_inner_margin 0 border_outer_margin 0 minimum_size 200 250 maximum_width 200 alignment tr gap_x 220 gap_y 280 # Graphics settings # draw_shades no draw_outline no draw_borders no draw_graph_borders no # Text settings # use_xft yes xftfont caviar dreams:size=8 xftalpha 0.5 uppercase no temperature_unit celsius default_color FFFFFF # Lua Load # lua_load ~/.lua/scripts/clock_rings.lua lua_draw_hook_pre clock_rings

  Read the article

• SSH login very slow on OS X Leopard

  - by acjohnson55

  My SSH sessions take a very long time to initiate. This applies for logins with and without passwords, interactive and non-interactive. I have tried setting 'GSSAPIAuthentication no' and 'IPQoS 0x00' on the client side, and 'UseDNS no' on the server side, but no dice. I'm really stumped and frustrated. The worst part is that it SFTP takes forever to establish connections too, making file transfer much longer than it would be otherwise. I thought the problem might be something with PAM, because of where the hang is in the sshd log below, so I tried commenting out each line one-by-one in the /etc/pam.d/sshd file. Some caused login to be impossible, some had no apparent effect. I can't really tell if PAM is stalling for other services, but I can say that su'ing into my account from another account with 'su -l' has no apparent delay. I tried creating a new user account, just to see if there was something wrong with my existing account, and the same problem persisted. Any ideas of what's going on? On the client side, the most verbose mode outputs (redacted where reasonable): OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data ... debug1: ... line 1: Applying options for ... debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 53: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to ... [x.x.x.x] port 22. debug1: Connection established. debug1: identity file /.../.ssh/id_rsa type -1 debug1: identity file /.../.ssh/id_rsa-cert type -1 debug3: Incorrect RSA1 identifier debug3: Could not load "/.../.ssh/id_dsa" as a RSA1 public key debug1: identity file /.../.ssh/id_dsa type 2 debug1: identity file /.../.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.2 debug1: match: OpenSSH_5.2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug2: fd 3 setting O_NONBLOCK debug3: load_hostkeys: loading entries for host "..." from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug3: order_hostkeyalgs: prefer hostkeyalgs: [email protected],[email protected],ssh-rsa debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],ssh-rsa,[email protected],[email protected],ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 136/256 debug2: bits set: 523/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ... debug3: load_hostkeys: loading entries for host "..." from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug3: load_hostkeys: loading entries for host "x.x.x.x" from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug1: Host '...' is known and matches the RSA host key. debug1: Found key in /.../.ssh/known_hosts:9 debug2: bits set: 492/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /.../.ssh/id_dsa (0x7f8b7b41d6c0) debug2: key: /.../.ssh/id_rsa (0x0) debug1: Authentications that can continue: publickey,password,keyboard-interactive debug3: start over, passed a different list publickey,password,keyboard-interactive debug3: preferred publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering DSA public key: /.../.ssh/id_dsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-dss blen 434 debug2: input_userauth_pk_ok: fp ... debug3: sign_and_send_pubkey: DSA ... debug1: Authentication succeeded (publickey). Authenticated to ... ([x.x.x.x]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. ****** Hangs here ****** debug2: callback start debug2: client_session2_setup: id 0 debug2: fd 3 setting TCP_NODELAY debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env TERM_PROGRAM debug3: Ignored env SHELL debug3: Ignored env TERM debug3: Ignored env TMPDIR debug3: Ignored env Apple_PubSub_Socket_Render debug3: Ignored env TERM_PROGRAM_VERSION debug3: Ignored env TERM_SESSION_ID debug3: Ignored env USER debug3: Ignored env COMMAND_MODE debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env Apple_Ubiquity_Message debug3: Ignored env __CF_USER_TEXT_ENCODING debug3: Ignored env PATH debug3: Ignored env MKL_NUM_THREADS debug3: Ignored env PWD debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env DYLD_LIBRARY_PATH debug3: Ignored env PYTHONPATH debug3: Ignored env LOGNAME debug3: Ignored env DISPLAY debug3: Ignored env SECURITYSESSIONID debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 On the server side, the debug output looks like: Sep 16 18:46:40 ... sshd[31435]: debug1: inetd sockets after dupping: 3, 4 Sep 16 18:46:40 ... sshd[31435]: Connection from x.x.x.x port 52758 Sep 16 18:46:40 ... sshd[31435]: debug1: Current Session ID is 56AC0FB0 / Session Attributes are 00008000 Sep 16 18:46:40 ... sshd[31435]: debug1: Running in inetd mode in a non-root session... assuming inetd created the session for us. Sep 16 18:46:40 ... sshd[31435]: debug1: Client protocol version 2.0; client software version OpenSSH_5.9 Sep 16 18:46:40 ... sshd[31435]: debug1: match: OpenSSH_5.9 pat OpenSSH* Sep 16 18:46:40 ... sshd[31435]: debug1: Enabling compatibility mode for protocol 2.0 Sep 16 18:46:40 ... sshd[31435]: debug1: Local version string SSH-2.0-OpenSSH_5.2 Sep 16 18:46:40 ... sshd[31435]: debug1: Checking with Service ACLs for ssh login restrictions Sep 16 18:46:40 ... sshd[31435]: debug1: call to mbr_user_name_to_uuid with <...> suceeded to retrieve user_uuid Sep 16 18:46:40 ... sshd[31435]: debug1: Call to mbr_check_service_membership failed with status <0> Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: initializing for "..." Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: setting PAM_RHOST to "x.x.x.x" Sep 16 18:46:40 ... sshd[31435]: Failed none for ... from x.x.x.x port 52758 ssh2 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys2 Sep 16 18:46:40 ... sshd[31435]: debug1: fd 5 clearing O_NONBLOCK Sep 16 18:46:40 ... sshd[31435]: debug1: matching key found: file /.../.ssh/authorized_keys2, line 1 Sep 16 18:46:40 ... sshd[31435]: Found matching DSA key: ... Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys2 Sep 16 18:46:40 ... sshd[31435]: debug1: fd 5 clearing O_NONBLOCK Sep 16 18:46:40 ... sshd[31435]: debug1: matching key found: file /.../.ssh/authorized_keys2, line 1 Sep 16 18:46:40 ... sshd[31435]: Found matching DSA key: ... Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: ssh_dss_verify: signature correct Sep 16 18:46:40 ... sshd[31435]: debug1: do_pam_account: called Sep 16 18:46:40 ... sshd[31435]: Accepted publickey for ... from x.x.x.x port 52758 ssh2 Sep 16 18:46:40 ... sshd[31435]: debug1: monitor_child_preauth: ... has been authenticated by privileged process Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: establishing credentials ***** Hangs here ***** Sep 16 18:46:54 ... sshd[31435]: User child is on pid 31654 Sep 16 18:46:54 ... sshd[31654]: debug1: PAM: establishing credentials Sep 16 18:46:54 ... sshd[31654]: debug1: permanently_set_uid: 509/20 Sep 16 18:46:54 ... sshd[31654]: debug1: Entering interactive session for SSH2. Sep 16 18:46:54 ... sshd[31654]: debug1: server_init_dispatch_20 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_open: ctype session rchan 0 win 1048576 max 16384 Sep 16 18:46:54 ... sshd[31654]: debug1: input_session_request Sep 16 18:46:54 ... sshd[31654]: debug1: channel 0: new [server-session] Sep 16 18:46:54 ... sshd[31654]: debug1: session_new: session 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_open: channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_open: session 0: link with channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_open: confirm session Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_global_request: rtype [email protected] want_reply 0 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request pty-req reply 1 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req pty-req Sep 16 18:46:54 ... sshd[31654]: debug1: Allocating pty. Sep 16 18:46:54 ... sshd[31435]: debug1: session_new: session 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_pty_req: session 0 alloc /dev/ttys008 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request env reply 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req env Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request shell reply 1 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req shell Sep 16 18:46:54 ... sshd[31655]: debug1: Setting controlling tty using TIOCSCTTY.

  Read the article

• How can I get FreeNAS to respond to libvirt shutdown requests

  - by ptomli

  I have a KVM VM of FreeNAS 0.7.1 Shere (revision 5127) running on Ubuntu Server 10.04 and I'm unable to convince the VM to shutdown from the host virsh shutdown freenas I would expect this to send some ACPI? trigger to the VM and FreeNAS then do what it's told. I'm not a FreeBSD fundi so I don't really know what packages or processes to poke to get this running. I have tried to convince powerd to run, but the VM cpus don't have the required freq entry Sysctl HW $ sysctl hw hw.machine: amd64 hw.model: QEMU Virtual CPU version 0.12.3 hw.ncpu: 1 hw.byteorder: 1234 hw.physmem: 523116544 hw.usermem: 463806464 hw.pagesize: 4096 hw.floatingpoint: 1 hw.machine_arch: amd64 hw.realmem: 536850432 hw.aac.iosize_max: 65536 hw.amr.force_sg32: 0 hw.an.an_cache_iponly: 1 hw.an.an_cache_mcastonly: 0 hw.an.an_cache_mode: dbm hw.an.an_dump: off hw.ata.to: 15 hw.ata.wc: 1 hw.ata.atapi_dma: 1 hw.ata.ata_dma_check_80pin: 1 hw.ata.ata_dma: 1 hw.ath.txbuf: 200 hw.ath.rxbuf: 40 hw.ath.regdomain: 0 hw.ath.countrycode: 0 hw.ath.xchanmode: 1 hw.ath.outdoor: 1 hw.ath.calibrate: 30 hw.ath.hal.swba_backoff: 0 hw.ath.hal.sw_brt: 10 hw.ath.hal.dma_brt: 2 hw.bce.msi_enable: 1 hw.bce.tso_enable: 1 hw.bge.allow_asf: 0 hw.cardbus.cis_debug: 0 hw.cardbus.debug: 0 hw.cs.recv_delay: 570 hw.cs.ignore_checksum_failure: 0 hw.cs.debug: 0 hw.cxgb.snd_queue_len: 50 hw.cxgb.use_16k_clusters: 1 hw.cxgb.force_fw_update: 0 hw.cxgb.singleq: 0 hw.cxgb.ofld_disable: 0 hw.cxgb.msi_allowed: 2 hw.cxgb.txq_mr_size: 1024 hw.cxgb.sleep_ticks: 1 hw.cxgb.tx_coalesce: 0 hw.firewire.hold_count: 3 hw.firewire.try_bmr: 1 hw.firewire.fwmem.speed: 2 hw.firewire.fwmem.eui64_lo: 0 hw.firewire.fwmem.eui64_hi: 0 hw.firewire.phydma_enable: 1 hw.firewire.nocyclemaster: 0 hw.firewire.fwe.rx_queue_len: 128 hw.firewire.fwe.tx_speed: 2 hw.firewire.fwe.stream_ch: 1 hw.firewire.fwip.rx_queue_len: 128 hw.firewire.sbp.tags: 0 hw.firewire.sbp.use_doorbell: 0 hw.firewire.sbp.scan_delay: 500 hw.firewire.sbp.login_delay: 1000 hw.firewire.sbp.exclusive_login: 1 hw.firewire.sbp.max_speed: -1 hw.firewire.sbp.auto_login: 1 hw.mfi.max_cmds: 128 hw.mfi.event_class: 0 hw.mfi.event_locale: 65535 hw.pccard.cis_debug: 0 hw.pccard.debug: 0 hw.cbb.debug: 0 hw.cbb.start_32_io: 4096 hw.cbb.start_16_io: 256 hw.cbb.start_memory: 2281701376 hw.pcic.pd6722_vsense: 1 hw.pcic.intr_mask: 57016 hw.pci.honor_msi_blacklist: 1 hw.pci.enable_msix: 1 hw.pci.enable_msi: 1 hw.pci.do_power_resume: 1 hw.pci.do_power_nodriver: 0 hw.pci.enable_io_modes: 1 hw.pci.host_mem_start: 2147483648 hw.syscons.kbd_debug: 1 hw.syscons.kbd_reboot: 1 hw.syscons.bell: 1 hw.syscons.saver.keybonly: 1 hw.syscons.sc_no_suspend_vtswitch: 0 hw.usb.uplcom.interval: 100 hw.usb.uvscom.interval: 100 hw.usb.uvscom.opktsize: 8 hw.wi.debug: 0 hw.wi.txerate: 0 hw.xe.debug: 0 hw.intr_storm_threshold: 1000 hw.availpages: 127714 hw.bus.devctl_disable: 0 hw.ste.rxsyncs: 0 hw.busdma.total_bpages: 32 hw.busdma.zone0.total_bpages: 32 hw.busdma.zone0.free_bpages: 32 hw.busdma.zone0.reserved_bpages: 0 hw.busdma.zone0.active_bpages: 0 hw.busdma.zone0.total_bounced: 0 hw.busdma.zone0.total_deferred: 0 hw.busdma.zone0.lowaddr: 0xffffffff hw.busdma.zone0.alignment: 2 hw.busdma.zone0.boundary: 65536 hw.clockrate: 2808 hw.instruction_sse: 1 hw.apic.enable_extint: 0 hw.kbd.keymap_restrict_change: 0 hw.acpi.supported_sleep_state: S3 S4 S5 hw.acpi.power_button_state: S5 hw.acpi.sleep_button_state: S3 hw.acpi.lid_switch_state: NONE hw.acpi.standby_state: S1 hw.acpi.suspend_state: S3 hw.acpi.sleep_delay: 1 hw.acpi.s4bios: 0 hw.acpi.verbose: 0 hw.acpi.disable_on_reboot: 0 hw.acpi.handle_reboot: 0 hw.acpi.cpu.cx_lowest: C1 Processes $ ps ax PID TT STAT TIME COMMAND 0 ?? DLs 0:00.00 [swapper] 1 ?? ILs 0:00.00 /sbin/init -- 2 ?? DL 0:00.08 [g_event] 3 ?? DL 0:00.29 [g_up] 4 ?? DL 0:00.33 [g_down] 5 ?? DL 0:00.00 [crypto] 6 ?? DL 0:00.00 [crypto returns] 7 ?? DL 0:00.00 [xpt_thrd] 8 ?? DL 0:00.00 [kqueue taskq] 9 ?? DL 0:00.00 [acpi_task_0] 10 ?? RL 34:12.42 [idle: cpu0] 11 ?? WL 0:01.13 [swi4: clock sio] 12 ?? WL 0:00.00 [swi3: vm] 13 ?? WL 0:00.00 [swi1: net] 14 ?? DL 0:00.04 [yarrow] 15 ?? WL 0:00.00 [swi6: task queue] 16 ?? WL 0:00.00 [swi2: cambio] 17 ?? DL 0:00.00 [acpi_task_1] 18 ?? DL 0:00.00 [acpi_task_2] 19 ?? WL 0:00.00 [swi5: +] 20 ?? DL 0:00.01 [thread taskq] 21 ?? WL 0:00.00 [swi6: Giant taskq] 22 ?? WL 0:00.00 [irq9: acpi0] 23 ?? WL 0:00.09 [irq14: ata0] 24 ?? WL 0:00.11 [irq15: ata1] 25 ?? WL 0:00.57 [irq11: ed0 uhci0] 26 ?? DL 0:00.00 [usb0] 27 ?? DL 0:00.00 [usbtask-hc] 28 ?? DL 0:00.00 [usbtask-dr] 29 ?? WL 0:00.01 [irq1: atkbd0] 30 ?? WL 0:00.00 [swi0: sio] 31 ?? DL 0:00.00 [sctp_iterator] 32 ?? DL 0:00.00 [pagedaemon] 33 ?? DL 0:00.00 [vmdaemon] 34 ?? DL 0:00.00 [idlepoll] 35 ?? DL 0:00.00 [pagezero] 36 ?? DL 0:00.01 [bufdaemon] 37 ?? DL 0:00.00 [vnlru] 38 ?? DL 0:00.14 [syncer] 39 ?? DL 0:00.01 [softdepflush] 1221 ?? Is 0:00.00 /sbin/devd 1289 ?? Is 0:00.01 /usr/sbin/syslogd -ss -f /var/etc/syslog.conf 1608 ?? Is 0:00.00 /usr/sbin/cron -s 1692 ?? Ss 0:00.03 /usr/local/sbin/mDNSResponderPosix -b -f /var/etc/mdn 1730 ?? S 0:00.43 /usr/local/sbin/lighttpd -f /var/etc/lighttpd.conf -m 1882 ?? DL 0:00.00 [system_taskq] 1883 ?? DL 0:00.00 [arc_reclaim_thread] 4139 ?? S 0:00.03 /usr/local/bin/php /usr/local/www/exec.php 4144 ?? S 0:00.00 sh -c ps ax 4145 ?? R 0:00.00 ps ax 1816 v0 Is 0:00.01 login [pam] (login) 1818 v0 I+ 0:00.03 -tcsh (csh) 1817 v1 Is+ 0:00.00 /usr/libexec/getty Pc ttyv1 1402 con- I 0:00.00 /usr/local/sbin/afpd -F /var/etc/afpd.conf 1404 con- S 0:00.00 /usr/local/sbin/cnid_metad 1682 con- I 0:02.78 /usr/local/sbin/mt-daapd -m -c /var/etc/mt-daapd.conf 1789 con- S 0:00.18 /usr/local/bin/fuppesd --config-dir /var/etc --config Libvert snippet <domain type='kvm'> <name>freenas</name> <uuid>********-****-****-****-************</uuid> <memory>524288</memory> <currentMemory>524288</currentMemory> <vcpu>1</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> Is this possible? Ideally I'd like to be able to stop the host without having to manually deal with shutting down the VM.

  Read the article

• How do I configure nVidia drivers on a Portable Ubuntu setup?

  - by Nicholas Flynt

  I've been pulling my hair out over this one for a couple of days now, google is no help. I've created a wonderful (until this issue) portable copy of Ubuntu linux that will boot on mostly anything by using a USB enclosure for my laptop's 80GB SATA drive. So far so good, it boots and runs on everything, and on non-nVidia card setups was even detecting the drivers, or letting me install the required drivers for hardware acceleration and compiz. Because you know, the wobble windows are the most awesome thing ever. Anyway, my desktop machine had an nVidia card, so I'm thinking, sure, I'll just install the nVidia drivers like before and everything will work happily. Not so-- now the desktop and any other nVidia cards work great, but it seems to have completely disabled any other graphics cards. When the kernel module detects that an nVidia card isn't present, it shoots up this nasty little dialog box giving me the option to boot into "low graphics" mode, which doesn't even allow me to use the correct screen resolution, much less see the installed graphics card and try to configure a driver for it. Is there any way to configure Ubuntu (with the dreaded nVidia kernel module) so that it can use nVidia's drivers when an nVidia card is present, and default to the normal (not low-graphics) setup in other cases, so that it has a fair chance of using what's actually present? I'm not afraid to much with config files, I just don't know the underlying system well enough to feel comfortable diving in without a push in the right direction. Thanks guys!

  Read the article

• Outlook Shared Address book and contact not displaying

  - by user224061

  We have a shared Exchange addressbook with distribution email groups. When someone connects to the shared addressbook, composes an email to a group, the email distribution list is empty, then the distribution list is expanded. In troubleshooting, I noticed that when we expand the distribution list to view the recipients, most of the recipients are missing and only semicolons appear. CLICK HERE FOR IMAGE Further troubleshooting, I notice that when I open the distribution list with my Outlook client and click on the Update Now icon, and then go to create the email then when I expand the group the email addresses now appear. CLICK HERE FOR IMAGE Now, my Outlook profile is a cached profile. The shared contact list that I pulled the distribution list from is an online/non-cached shared contact list. What I also found is that if I switched my Outlook client to be online only(not cached) the share address book lists appear properly when expanded. Is there any way to make this list appear correctly without having to click on update now for each and every distribution list in the shared contacts list we have on the server? I would really prefer that every time one wants to use this shared contact list, they do not have o click the update not button or switch from cached mode to make this work. T.I.A

  Read the article

• How can I systematically shut down Windows services in order?

  - by cbmeeks

  We have this open source application that has three (3) services. For the purpose of this question, let's call them A, B, and C. Now, they have to be shut down in a specific order. That order would be A then B then C. If B shuts down before A then we run into all kinds of problems. Same is true if C shuts down before B or A. Plus, each service can take a different amount of time to shut down due to how many users were using it. Oh, this need to be wrapped up in a DOS batch file or something a non-techy user could just double-click to initiate. (PowerShell is not out of the question but I've never used it). Also, I'm a C# coder so that could be used too. Anyway, when the restart is initiated the following needs to happen: 1) Initiate shutdown of service A 2) When service A is down, it should trigger the shutdown of service B 3) When service B is down, it should trigger the shutdown of service C 4) When service C is down, it should trigger the START UP of service A 5) When service A is UP, it should trigger the START UP of service B 6) When service B is UP, it should trigger the START UP of service C So as you can see, each stop/start needs to wait on the previous to be completely finished before moving on. And since each service can take a few seconds to a few minutes, we can't use any kind of timing tricks. Suggestions greatly appreciated. Thanks!

  Read the article

• Windows 7 - mysteriously missing free HDD space

  - by sYnfo

  I have Windows7 installed on 50GB (Oops, it should have been 45GB, sorry) partition, and every now and then it gets full, and I have to resize that partition. I always thought it is quite normal. But it happened again today and this time, I'm sure it is not normal, because since last resizing (35GB 45GB) I did not install any new apps or whatever. Also, sum of sizes off all, including hidden & system, root folders and files is ~18GB, yet windows is indicating that all 50GB are used up... Any idea what is going on? EDIT: Great tools everyone! (SourceForge appears to be offline at the moment, I'll check WinDirStat later) Alas, non of them solved my problem just yet... Screenshot from SpaceSniffer: On the right there is some kind of "Unknows Space", any idea what that could be? EDIT2: After those two apps failing to help much I didn't expect it, but WinDirStat actually helped. It showed that those missing 27GB are in my Temp folder (Well, that should have been my first guess anyway). There I found hundreds of ~100MB files, named like HTT????.tmp. After some googling it appears to be a problem with ESET NOD32 antivirus and it's ThreatSense feature. Thank you all for help! :)

  Read the article

• Password Cracking Windows Accounts

  - by Kevin

  At work we have laptops with encrypted harddrives. Most developers here (on occasion I have been guilty of it too) leave their laptops in hibernate mode when they take them home at night. Obviously, Windows (i.e. there is a program running in the background which does it for windows) must have a method to unencrypt the data on the drive, or it wouldn't be able to access it. That being said, I always thought that leaving a windows machine on in hibernate mode in a non-secure place (not at work on a lock) is a security threat, because someone could take the machine, leave it running, hack the windows accounts and use it to encrypt the data and steal the information. When I got to thinking about how I would go about breaking into the windows system without restarting it, I couldn't figure out if it was possible. I know it is possible to write a program to crack windows passwords once you have access to the appropriate file(s). But is it possible to execute a program from a locked Windows system that would do this? I don't know of a way to do it, but I am not a Windows expert. If so, is there a way to prevent it? I don't want to expose security vulnerabilities about how to do it, so I would ask that someone wouldn't post the necessary steps in details, but if someone could say something like "Yes, it's possible the USB drive allows arbitrary execution," that would be great! EDIT: The idea being with the encryption is that you can't reboot the system, because once you do, the disk encryption on the system requires a login before being able to start windows. With the machine being in hibernate, the system owner has already bypassed the encryption for the attacker, leaving windows as the only line of defense to protect the data.

  Read the article

• Optimum configuration of McAfee for Servers

  - by Wayne Arthurton

  Our corporate standard is McAfee Enterprise, unfortunately this is non-negotiable. On two types of servers I'm responsible for, SQL & Web, we have noticed major performance issues with the corporate standard setup. Max scan time 45sec One policy for all processes Scan ALL files on write, read and open for backup Heuristics: Find unknown programs, trojans and macros Detect unwanted programs Exclude: EVT, LDF, LOG, MDF, VMD, , windows file protection) This of course still causes major slowdowns. IIS .NET recompiles are slow especially with SharePoint, SQL backups and restores, SQL Analysis Services, Integration Services and temp data from them as well. I have looked from time to time, for some best practices on setting up McAfee of SQL & SQL Analysis Service, SQL Integration Service, Visual Studio, Sharepoint, and .NET web servers in general. How do people setup McAfee enterprise on their corporate serves keeping security intact, but affecting performance as minimally as possible? Has anyone run across white papers on these setups? Obviously some are case by case, but there must be some best practices out there somewhere.

  Read the article

• SPDIF passthrough not working in Windows 7

  - by adriangrigore

  Hi, I'm running Windows 7 on a computer with an Audigy Platinum eX sound card connected to a surround receiver via optical cabling. Sound works fine when listening to non-surround audio sources, such as windows sounds or MP3. However, when I view a DVD in Media Center and the SPDIF passthrough kicks in, I can only hear an awful noise instead of the movie soundtrack. Also, the receiver does not show the Dolby Digital or DTS symbol, but stays at Dolby Prologic, so it seems it doesn't identify the sound encoding properly. I could switch off SPDIF passthrough and use the sound card's decoder instead, but that's not an option for me since it would create more problems with regular MP3 playback via additional Stereo Receiver which is also connected to the same sound card. I've tried both the default Audigy drivers that come with Windows 7 and the latest drivers from the Soundblaster website, but the problem remains unchanged. Also, I have ensured that the receiver's Dolby Digital decoder is not broken by successfully connecting it to my PS3 to view a Dolby Digital DVD. Besides, SPDIF passthrough was working fine in Vista before I upgraded to Windows 7. Is there anything else I could try?

  Read the article

• apache 2.4, mod_proxy_fcgi not honouring .htaccess, work around needed

  - by user229874

  I am using apache 2.4.7 with mod_proxy_fcgi for purpose of passing through php to php-fpm (this will be used for shared hosting environment). The htaccess works fine for non php files, but once it hit rewrite rule that proxies through the php requests, the htaccess is ignored. I know why it is happening. The question is: how do I work around it? The question how do I force apache to treat the request to php file as a request to local file, and then proxy it through? I have spent substantial time in researching on this problem, and following "answers" were given as solution: 1) "use apache configuration instead of .htaccess" it is valid solution, but not for shared hosting environment (I am not going to give access to apache configuration to shared hosting customers ;)). 2) "don't use .htaccess, as it has performance/security/other issues", well how else would shared hosting customers control access/url rewriting on their site? Besides if the .htaccess was not a requirement I would simply use nginx. 3) "put rewrite rule for proxy inside of " - this is incorrect, and it does not work. This behaviour appears to be not a bug but a "feature" as per https://issues.apache.org/bugzilla/show_bug.cgi?id=54887

  Read the article

• Apache ProxyPass with SSL

  - by BBonifield

  I have a QA setup that consists of multiple internal development servers and one world-accessible provisioning machine that is setup to proxy pass the web traffic. Everything works fine for non-SSL requests, but I'm having a hard time getting the SSL logic working as well. Here's a few example vhost blocks. <VirtualHost 192.168.168.101:443> ProxyPreserveHost On SSLProxyEngine On ProxyPass / https://192.168.168.111/ ServerName dev1.site.com </VirtualHost> <VirtualHost 192.168.168.101:80> ProxyPreserveHost On ProxyPass / http://192.168.168.111/ ServerName dev1.site.com </VirtualHost> <VirtualHost 192.168.168.101:443> ProxyPreserveHost On SSLProxyEngine On ProxyPass / https://192.168.168.111/ ServerName dev2.site.com </VirtualHost> <VirtualHost 192.168.168.101:80> ProxyPreserveHost On ProxyPass / http://192.168.168.111/ ServerName dev2.site.com </VirtualHost> I end up seeing the following error in the provisioner's error log. [Fri Jan 28 12:50:59 2011] [warn] [client 1.2.3.4] proxy: no HTTP 0.9 request (with no host line) on incoming request and preserve host set forcing hostname to be dev1.site.com for uri / As well as the following entry in the destination QA machine's access log. 192.168.168.101 - - [22/Feb/2011:08:34:56 -0600] "\x16\x03\x01 / HTTP/1.1" 301 326 "-" "-"

  Read the article

• How can I recover from SharePoint configuration errors after promoting the server to a Domain Controller?

  - by jjr2527

  I have a SharePoint 2010 VM setup in VirtualBox and I was using local machine accounts to handle security on the server. While preparing for a demo it came time to have some meaningful users on my VM image. I followed some docs on promoting my server to a Domain Controller in a new forrest. So now I have [MachineName].SPDEMO.CONTOSO.com and I can add users as needed. However, when I try to connect to my SharePoint sites I am getting a white screen with the error: "Cannot connect to the configuration database" I changed the pool identity account of each of my IIS app pools to the new Administrator account and started the services successfully but I can't get the SQL services to start up. When I try to start them I get the following error: Windows could not start the SQL Server (MSSQLSERVER) on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service vendor, and refer to service-specific error code 17058. In the event log I see the following error: The SQL Server (MSSQLSERVER) service terminated with service-specific error %%17058. Can I recover from this or should I roll back or just uninstall the Domain Controller role. I'd like to keep the server as a standalone DC so I can do some user profile creation/management but I need the SharePoint bits to work as well.

  Read the article

• What is causing Null Pointer Exception in the following code in java? [migrated]

  - by Joe

  When I run the following code I get Null Pointer Exception. I cannot figure out why that is happening. Need Help. public class LinkedList<T> { private Link head = null; private int length = 0; public T get(int index) { return find(index).item; } public void set(int index, T item) { find(index).item = item; } public int length() { return length; } public void add(T item) { Link<T> ptr = head; if (ptr == null) { // empty list so append to head head = new Link<T>(item); } else { // non-empty list, so locate last link while (ptr.next != null) { ptr = ptr.next; } ptr.next = new Link<T>(item); } length++; // update length cache } // traverse list looking for link at index private Link<T> find(int index) { Link<T> ptr = head; int i = 0; while (i++ != index) { if(ptr!=null) { ptr = ptr.next; } } return ptr; } private static class Link<S> { public S item; public Link<S> next; public Link(S item) { this.item = item; } } public static void main(String[] args) { new LinkedList<String>().get(1); } }

  Read the article

• Passing two arguments to a command using pipes

  - by firebat

  Usually, we only need to pass one argument: echo abc | cat echo abc | cat some_file - echo abc | cat - some_file Is there a way to pass two arguments? Something like {echo abc , echo xyz} | cat cat `echo abc` `echo xyz` I could just store both results in a file first echo abc > file1 echo xyz > file2 cat file1 file2 But then I might accidentally overwrite a file, which is not ok. This is going into a non-interactive script. Basically, I need a way to pass the results of two arbitrary commands to cat without writing to a file. UPDATE: Sorry, the example masks the problem. While { echo abc ; echo xyz ; } | cat does seem to work, the output is due to the echos, not the cat. A better example would be { cut -f2 -d, file1; cut -f1 -d, file2; } | paste -d, which does not work as expected. With file1: a,b c,d file2: 1,2 3,4 Expected output is: b,1 d,3 RESOLVED: Use process substitution: cat <(command1) <(command2) Alternatively, make named pipes using mkfifo: mkfifo temp1 mkfifo temp2 command1 > temp1 & command2 > temp2 & cat temp1 temp2 Less elegant and more verbose, but works fine, as long as you make sure temp1 and temp2 don't exist before hand.

  Read the article

• Ruby Passeger + Nginx or lighthttpi + fgci for shared hosting

  - by devnull

  I have set up a passenger + nginx setup and I plan to offer a free non-commercial hosting (or in fact on the fly deployment) for rack-based frameworks (e.g. camping, sinatra). I am facing an "issue" with passenger. For each application you need to configure nginx.conf (it would be the same with apache so it is not an nginx issue) with: server { ... passenger_base_uri /app1; passenger_base_uri /app2; passenger_base_uri /app3; } Now this is not inherently bad as, in theory, I could allow a user to run just one app on his webspace but even in this case I need to create a new server directory on nginx e.g. (user.domain.com). As this will mainly be used to deploy apps the behavior I am looking at is more the possibility to auto map several apps (e.g. app1, app2, app3, app4) under the same server (your app.com/app1 yourapp.com/app2) without having to update the nginx or apache file each time. This seems to be a limitation in passenger. As such I am thinking about an alternative with lighttpd and fastcgi. Would this allow immediate deployment without touching the lighttpd config file e.g. I create a new directory with app2 and it will run immediately ? What is your experience in performance difference between passenger + nginx vs. lighttpd + fastcgi ? thanks in advance scenario details: on nginx + passenger - user cannot add a new sub-folder and run another sinatra/camping app without declaring the path on nginx.conf and restarting the server; wished behavior with the new setup: - user can add a new folder with a new app and it would run on lighttpd+fcgi without any extra configuration of the web server;

  Read the article

• Under which circumstances can a *local* user account access a remote SQL Server with a trusted connection?

  - by Heinzi

  One of our customers has the following configuration: On the domain controller, there's an SQL Server. On his PC (WinXP), he logs on with LocalPC\LocalUser. In Windows Explorer, he opens DomainController\SomeShare and authenticates as Domain\Administrator. He starts our application, which opens a trusted connection (Windows authentication) to the SQL Server. It works. In SSMS, the connection shows up with the user Domain\Administrator. Firstly, I was surprised that this even works. (My first suspicion was that there is a user with the same name and password in the domain, but there is no user LocalUser in the domain.) Then we tried to reproduce the same behaviour on his new PC, but failed: On his new PC (Win7), he logs on with OtherLocalPC\OtherLocalUser. In Windows Explorer, he opens DomainController\SomeShare and authenticates as Domain\Administrator. He starts our application, which opens a trusted connection (Windows authentication) to the SQL Server. It fails with the error message Login failed for user ''. The user is not associated with a trusted SQL Server connection. Hence my question: Under which conditions can a non-domain user access a remote SQL Server using Windows Authentication with different credentials? Apparently, it's possible (it works on his old PC), but why? And how can I reproduce it?

  Read the article

• CentOS 6.3 X86_64 RAM detection

  - by Peter

  I have a machine with 8GB ram (BIOS sees it, so my motherboard and CPU supports it), and I installed CentOS 6.3 on it. When it starts up, it only see 3.1GB. uname says: 2.6.32-279.1.1.el6.x86_64 #1 SMP BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000cf65f000 (usable) BIOS-e820: 00000000cf65f000 - 00000000cf6e8000 (ACPI NVS) BIOS-e820: 00000000cf6e8000 - 00000000cf6ec000 (usable) BIOS-e820: 00000000cf6ec000 - 00000000cf6ff000 (ACPI data) BIOS-e820: 00000000cf6ff000 - 00000000cf700000 (usable) dmesg | grep -i memory says: initial memory mapped : 0 - 20000000 init_memory_mapping: 0000000000000000-00000000cf700000 Reserving 129MB of memory at 48MB for crashkernel (System RAM: 3319MB) PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 PM: Registered nosave memory: 00000000cf65f000 - 00000000cf6e8000 PM: Registered nosave memory: 00000000cf6ec000 - 00000000cf6ff000 Memory: 3184828k/3398656k available (5152k kernel code, 1016k absent, 212812k reserved, 7166k data, 1260k init) please try 'cgroup_disable=memory' option if you don't want memory cgroups Initializing cgroup subsys memory Freeing initrd memory: 16136k freed Non-volatile memory driver v1.3 agpgart-intel 0000:00:00.0: detected 8192K stolen memory crash memory driver: version 1.1 Freeing unused kernel memory: 1260k freed Freeing unused kernel memory: 972k freed Freeing unused kernel memory: 1732k freed Update: Memtest see all the 8GB, and dmidecode -t 17 | grep Size too. But free -m still see only 3.1 GB. Question: How can I repair/modify the system, to see all the 8GB RAM? Thanks in advance!

  Read the article

• Rsyslogd not listening on port

  - by amorfis

  I installed rsyslogd on ubuntu server, started it and everything looks fine, but the port the server should listen on is not opened. ubuntu@node7:~$ sudo service rsyslog restart rsyslog stop/waiting rsyslog start/running, process 14114 Netstat shows it is not listening: ubuntu@node7:~$ netstat -tlan Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 320 172.22.0.17:22 10.8.8.38:61335 ESTABLISHED tcp6 0 0 :::22 :::* LISTEN tcp6 0 0 :::2776 :::* LISTEN tcp6 0 0 :::2777 :::* LISTEN tcp6 0 0 172.22.0.17:2777 172.22.0.11:56554 ESTABLISHED tcp6 0 0 172.22.0.17:2776 172.22.0.11:39780 ESTABLISHED This is how /etc/rsyslog.conf looks like (most comments omitted): ubuntu@node7:~$ cat /etc/rsyslog.conf ################# #### MODULES #### ################# $ModLoad imuxsock # provides support for local system logging $ModLoad imklog # provides kernel logging support (previously done by rklogd) $ModLoad imtcp $InputTCPServerRun 514 ########################### #### GLOBAL DIRECTIVES #### ########################### $ActionFileDefaultTemplate RSYSLOG_TraditionalFileFormat $RepeatedMsgReduction on $WorkDirectory /var/spool/rsyslog $FileOwner syslog $FileGroup adm $FileCreateMode 0640 $DirCreateMode 0755 $Umask 0022 $PrivDropToUser syslog $PrivDropToGroup adm $IncludeConfig /etc/rsyslog.d/*.conf In /etc/rsyslog.d/35-server-per-host.conf I have following lines, and I suspect this can be the cause. What does it mean? # Stop processing of all non-local messages. You can process remote messages # on levels less than 35. :fromhost-ip,!isequal,"127.0.0.1" ~ and if it is, how could I change it to have server listening and receiving and logging messages? UPDATE: I commented out suspected line, but still it's not listening on port 514

  Read the article

• Line-length-tolerant XML diff

  - by Jon Skeet

  I've looked at the answers to this question, and unfortunately none of them has helped me so far. Not to beat about the bush, the second edition of C# in Depth is now in copy edit. I want to be able to see what the copy editor's done really easily, so I can reject or accept his changes. We're using a modified form of docbook, but I'm happy enough looking at the raw XML source. All fine so far - except that when the copy editor makes a change, that can change the line wrapping. So something that used to read: <para>Foo bar baz second line</para> now reads <para>Foo bar grontle baz second line</para> Now the real change here is the insertion of "grontle". I don't care that "baz" has moved from the first line to the second line... but all the diff tools I've seen do. I realise that one option would be to reformat the whole document (or possibly just whole paragraphs) into single lines... but that's then really hard to read, because diff tools don't wrap when they're displaying. I'm sure I can manage with the tools I've got, but if anyone knows of anything better, I'd be really glad to hear about it. I suspect my publishers would too :) (I've included the Windows tag here because I'd really need it to be available on Windows. I'd like to hear about any non-Windows software too, but only in case I could help to build it on Windows :)

  Read the article

• IPSec for LAN traffic: Basic considerations?

  - by chris_l

  This is a follow-up to my Encrypting absolutely everything... question. Important: This is not about the more usual IPSec setup, where you want to encrypt traffic between two LANs. My basic goal is to encrypt all traffic within a small company's LAN. One solution could be IPSec. I have just started to learn about IPSec, and before I decide on using it and dive in more deeply, I'd like to get an overview of how this could look like. Is there good cross-platform support? It must work on Linux, MacOS X and Windows clients, Linux servers, and it shouldn't require expensive network hardware. Can I enable IPSec for an entire machine (so there can be no other traffic incoming/outgoing), or for a network interface, or is it determined by firewall settings for individual ports/...? Can I easily ban non-IPSec IP packets? And also "Mallory's evil" IPSec traffic that is signed by some key, but not ours? My ideal conception is to make it impossible to have any such IP traffic on the LAN. For LAN-internal traffic: I would choose "ESP with authentication (no AH)", AES-256, in "Transport mode". Is this a reasonable decision? For LAN-Internet traffic: How would it work with the internet gateway? Would I use "Tunnel mode" to create an IPSec tunnel from each machine to the gateway? Or could I also use "Transport mode" to the gateway? The reason I ask is, that the gateway would have to be able to decrypt packages coming from the LAN, so it will need the keys to do that. Is that possible, if the destination address isn't the gateway's address? Or would I have to use a proxy in this case? Is there anything else I should consider? I really just need a quick overview of these things, not very detailed instructions.

  Read the article

• How do I make XTerm not use bold?

  - by mike

  I like using XTerm, I like its default "fixed" font, and I like using terminal colors rather than having a monochromatic terminal. However, XTerm seems to insist on using a bold version of the font whenever it's displaying a bright color: I hate hate hate the bold version of the font, but I like the brightness. The man page seems to suggest that adding "XTerm.VT100.boldMode:false" to my ~/.Xresources would disable this "feature", but it doesn't seem to have any effect. I've had it in there for months, so it's not a rebooting issue. How can I force XTerm to always use the standard, non-bold version of the fixed font, even when it's displaying bright text? Edit: Some have suggested putting "XTerm*boldMode: false" in my ~/.Xresources. That didn't help either. I've confirmed that the changes have taken effect with xrdb, though: $ xrdb -query | grep boldMode XTerm*boldMode: false And if i run xprop and click an xterm, I get "WM_CLASS(STRING) = "xterm", "XTerm"" .. so i'm definitely running real xterms. BTW, this is just a plain-vanilla Ubuntu Intrepid box. If anyone else here is running the same, can you try running: echo -e '#\e[1m#' ...and let me know whether the # on the right has a black pixel in the middle like the one on the left does?

  Read the article

• Windows XP dual screen problems, user account related

  - by Chris

  I have had this issue with a few laptops now and it looks like it is some sort of user account problem. Specifics of the system are: Dell Laptop Windows XP Pro SP3 Non-domain member computer DLP Projector connected to laptop via VGA I use this setup almost daily to do presentations, always the mirrored display mode where I can see on the laptop monitor the same thing that is displayed on the projector. Today, when I boot up, I get the mirrored display at the login screen, but after I log in, it switches to Extended Desktop (like two desktops side-by-side). Fn+F8 just cycles through all the normal settings except the mirrored display. I created a new user account on the computer and it performs normally. Mirrored display works as normal. I have run into this about 4 times now and it always can be solved by creating a new user account on the computer, and then all is well. I would like to either: 1. Find a way to reset the customized settings for a specific user account which would hopefully make this go away, or 2. Find the specific setting that causes this so that I can easily fix it when the problem comes up. Creating new user accounts is kind of a pain and a easy fix must be out there somewhere.

  Read the article

• Windows Vista claims wireless key is the wrong length

  - by humble coffee

  A family member of mine is house sitting and has been given the details of their wifi. The access point is an Airport Express, it has WEP encryption (I think) and they've been given a passphrase to use. I know it's a passphrase and not the encrypted key as it's an English word. The passphrase is 10 characters long. The problem is that Vista complains that it's not a valid key as it must be a 5 or 13 character non-hex key or a 10 or 26 character hex key. (From what I've read this suggests the encryption is WEP?) I've found a couple of suggested solutions, but I'm not actually at the house at the moment so I wanted to make sure I have a good chance of getting it to work when I'm there but have no internets to ask. Solution 1: Vista needs to be told explicitly what kind of encryption and key is being used. Specify in the connection settings that you are using WEP and that it is a "shared key". Solution2: Try converting the passphrase to hexadecimal using an ASCII-hex converter and entering that.

  Read the article

< Previous Page | 352 353 354 355 356 357 358 359 360 361 362 363  | Next Page >