Search Results

Search found 10397 results on 416 pages for 'mobile devices'.

Page 360/416 | < Previous Page | 356 357 358 359 360 361 362 363 364 365 366 367  | Next Page >

• IPSec tunnelling with ISA Server 2000...

  - by Izhido

  Believe it or not, our corporate network still uses ISA Server 2000 (in a Windows Server 2003 machine) to enable / control Internet access to / from it. I was asked recently to configure that ISA Server to create a site-to-site VPN for a new branch in a office about 25 km. away from it. The idea is basically to enable not only computers, but also Palm devices (WiFi-enabled, of course), to be able to see other computers in both sites. I was also told that a simple VPN-enabled wireless AP/router (in this case, a Cisco WRV210 unit) should be enough to establish communications with the main office. To be fair, the router looks easy to configure; it was confusing at first, but further understanding of how site-to-site VPNs work cleared all doubts about it. Now I need to make modifications to our ISA Server in order to recognize the newly installed & configured "remote" VPN site. Thing is, either my Googling skills are pathethically horrible, or there doesn't seem to be much (or any, at all) information about how to configure an ISA Server 2000 for this purpose. Lots of stuff on 2004, of course; also, I think I saw something for 2006. But nothing I could find about 2000. Reading about 2004, it seems that the only way I can do site-on-site with a Cisco router (read: a non-ISA-Server machine) is through something they call a "IPSec tunnel". Fair enough. However, I can't figure for the life of me how could I even start to find, leave alone configure, such a thing. Do you, people, happen to know how to do IPSec tunelling on a ISA Server 2000, so I can connect to a Cisco WRV210 VPN-enabled router, and build a site-to-site VPN for both networks? Or is this not possible at all? (Meaning I should change anything in this configuration to make it work...)

  Read the article

• WRT54GL Tomato Router in Client wireless mode to an iPhone Personal Hotspot

  - by Gordo

  I am trying to connect a router with Tomato firmware to an iPhone 4. The goal is to connect to the Personal Hotspot in Client Wireless mode. This should allow wired and wireless users to connect to the router rather then the iPhone. In theory this should be possible but I am having difficulty. Router Linksys WRT54GL Tomato 1.28.1816 firmware iPhone iPhone 4 iOS 5.1 (9B176) Carrier Rogers Wireless Personal Hotspot works with other devices, wifi/bluetooth/usb iPhone Personal Hotspot settings Mode: B/G Security: WPA or WPA2 Personal Encryption: AES Router IP: 172.20.10.1 Subnet: 172.20.10.0 Min IP: 172.20.10.2 Max IP: 172.20.10.14 maximum number of wireless tethered hosts is 5 I have followed the directions here: http://www.wi-fiplanet.com/tutorials/article.php/3810281 Ensured that the router subnet does not 'collide' with the iPhone subnet. Here is the configuration of the Tomato 'Basic - Network - Wireless' section: http://i.stack.imgur.com/pbmTB.png I have tried several variations of this configuration, but nothing seems to work. NOTE: I have successfully connected to my own wifi network in Wireless Client mode, so I am confident that there are no bad cables or other hardware issues. I would prefer to use Tomato, but DD-WRT maybe my only other option. Thanks!

  Read the article

• Do eSATA HDD docking stations have a capacity limit?

  - by Michael Kjörling

  I'm looking at perhaps buying an eSATA docking station to be able to easily plug in and unplug hard disk drives, particularly but not necessarily only for backup purposes. Note: This is not a hardware shopping recommendation question. Please don't vote to close it as such. Looking at different models, I find for example this page detailing the Deltaco SI-7908SUS which specifically states "storage capacity: 1.5 TB" as well as "pictured hard disk not included, only for illustration". A customer review specifically mentions that it does not work with 3 TB drives, although does not go into any detail such as OS, drive model, etc. From a brief glance, the vendor's web site does not appear to say either way. Then there is the quite similar Deltaco SI-7908B3 which boasts on the box "all 2.5" and 3.5" HDD/SSD compatible". My question is: Why would what basically amounts to a SATA/eSATA adapter have any say in what storage capacity devices are supported? Does it? Assuming the OS supports the full capacity of the drive, why should introducing another (not even a different, really) connector change anything? Bonus question: Might it make a difference if the docking station exposes multiple interfaces (such as in the case of for example the SI-7908SUS exposing USB 2.0 and eSATA)? (I still think it shouldn't, but it'd be nice to have it confirmed.)

  Read the article

• Zpool disk failure - Where am I at?

  - by JT.WK

  After checking the status of one of my zpools today, I was faced with the following: root@server: zpool status -v myPool pool: myPool state: ONLINE status: One or more devices has experienced an unrecoverable error. An attempt was made to correct the error. Applications are unaffected. action: Determine if the device needs to be replaced, and clear the errors using 'zpool clear' or replace the device with 'zpool replace'. see: http://www.sun.com/msg/ZFS-8000-9P scrub: resilver completed after 3h6m with 0 errors on Tue Sep 28 11:15:11 2010 config: NAME STATE READ WRITE CKSUM myPool ONLINE 0 0 0 raidz1 ONLINE 0 0 0 c6t7d0 ONLINE 0 0 0 c6t8d0 ONLINE 0 0 0 spare ONLINE 0 0 0 c6t9d0 ONLINE 54 0 0 c6t36d0 ONLINE 0 0 0 c6t10d0 ONLINE 0 0 0 c6t11d0 ONLINE 0 0 0 c6t12d0 ONLINE 0 0 0 spares c6t36d0 INUSE currently in use c6t37d0 AVAIL c6t38d0 AVAIL errors: No known data errors From what I can see, c6t9d0 has encountered 54 write errors. It seems as though it has automatically resilvered with the spare disk c6t36d0, which is now currently in use. My question is, where exactly am I at? Yes the 'action' tells me to determine whether or not the disk needs replacing, but is this disk currently still in use? Can I replace / remove it? Any explanation would be much appreciated as I'm quite new to this stuff :) update: After following the advice from C10k Consulting, ie detaching: zpool detach myPool c6t9d0 and adding as a spare: zpool add myPool spare c6t9d0 It appears as though all is well. The new status of my zpool is: root@server: zpool status -v myPool pool: myPool state: ONLINE scrub: resilver completed after 3h6m with 0 errors on Tue Sep 28 11:15:11 2010 config: NAME STATE READ WRITE CKSUM muPool ONLINE 0 0 0 raidz1 ONLINE 0 0 0 c6t7d0 ONLINE 0 0 0 c6t8d0 ONLINE 0 0 0 c6t36d0 ONLINE 0 0 0 c6t10d0 ONLINE 0 0 0 c6t11d0 ONLINE 0 0 0 c6t12d0 ONLINE 0 0 0 spares c6t37d0 AVAIL c6t38d0 AVAIL c6t9d0 AVAIL errors: No known data errors Thanks for your help c10k consulting :)

  Read the article

• USB Harddisk not working on dual boot windows7/8

  - by Jesper

  Yesterday I installed Windows 8 on a machine that already had Windows 7. They are on dual boot and both systems work fine. The problem is that inserting a USB hard disk in either system does nothing. If I connect a USB mouse or mobile phone, they work fine, so the USB plugs are active/working and the USB hard drives that I am trying to connect work on my other laptop just fine. I have tried to uninstall all USB-related items in Device Manager and let them reinstall upon restart, but that didn't help. The USB drive does not show up in disk management either. The strange thing is that it is exactly the same situation on both windows. USB mice etc. work just fine and USB hard drives do not. Any ideas on solving this problem would be great. ...Don't know if it is important, but this is a Toshiba Tecra R950 Laptop. EDIT: I have found out that my other USB HD (Western Digital) works on this laptop, but for my StoreJet Transcend and Adata "something" does not work. All three work on another Windows 7 laptop. Sizewise the WD is in the middle at 400 GB. The StoreJet is 640 GB and the Adata is 200 GB.

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7.

  Read the article

• Unable to Use Bluetooth Mighty Mouse or Wireless Keyboard with Boot Camp

  - by Kristopher Johnson

  I have Windows 7 64-bit running on a MacBook Pro in a Boot Camp partition. I am trying to pair with my Bluetooth Mighty Mouse and Apple wireless keyboard under Windows, but whenever I try to do so, here's what happens: While on the Add a device window, I turn on the mouse or press a key on the keyboard, and the mouse or keyboard shows up in the list of available devices. I click the device and then the Next button, and the window displays Connecting to device... Time passes. Eventually, I get this error message: Adding this device to this computer failed Adding the device failed resulting in an unknown error. The reported error code is 0x80070015. Contact your device manufacturer for assistance. I've run Windows Update and Apple Software Update. I've also tried reinstalling the drivers from the Snow Leopard DVD. The mouse and keyboard both work fine when I boot into Mac OS X. FWIW, after many, many repeated tries, I eventually got it to work. I don't know why. So while my problem is solved, I'd still like to get an "answer" as to why trial-and-error seems to be the only approach. The keyboard, in particular, was hard to get set up. A few times, Windows would apparently recognize it and prompt me to enter the pairing code, but then it would time out after a couple of seconds (not long enough to enter the code). Grrrr.

  Read the article

• Windows 7 DVD doesn't boot up, neither does USB. :'(

  - by Manan Shah

  My problem is that i'm not able to install windows 7. Been trying to install this since past 1 week. The methods i've tried are: I have a windows 7 bootable DVD which doesnt boot up. (I've set BIOS to boot from DVD ROM first but it just won't boot from the DVD). Tried to install Windows 7 from the same DVD to a friend's PC and it worked. So the DVD has no issues. I tried to run 'Setup.exe' from within the DVD. The two options pop-up 'Check compatibility' and 'Install now'. On clicking install now, after sometime, an error is encountered with the message 'Windows was unable to create a required installation folder' error code:0x8007000D. I am running Windows XP Professional and there's only one user on the PC which is the Admin, so i do not know why is the setup not getting permissions. I've also uninstalled my antivirus, CD burning software, disabled firewall and disconnected all other devices, but its still the same. I tried to install it from a USB device by making it bootable but that too doesnt work. (Yes the mobo supports booting from the USB). The problem is that XP does not recognize a 'USB' device on boot. Rather it shows this USB stick as a removable 'Hard Drive'. Furthermore, i changed the order of Hard Drive boot to boot from this removable Hard Drive first, it still boots my existing OS. Is there anything else that can be done? Any help would be greatly appreciated. :) Please ask if any other information is required, this post is becomimg increasingly long to add any other details. PS: I want to dual boot windows 7 with my existing XP, but that would be after i manage to run the windows 7 setup in the first place. PPS: Please bare with any 'not-so-technical' terms, i am a beginner with this. Again, thank you for taking the time and trying to help, really appreciate it. :)

  Read the article

• Why does my Intel Tolapai network chip not transmit packets?

  - by Hanno Fietz

  I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

  Read the article

• Will a 2.4Ghz WAP intefere with a 5.0Ghz WAP if placed directly next to each other

  - by Dan

  This is mostly a curiosity question to people who know more about radio and wi-fi than I. The 2.4Ghz band is massively overpopulated near my house to the point of sometimes getting 1000ms pings to the router from only a few feet away. inSSIDer finds at least 10 broadcasting SSID's within around 15 seconds of starting, so this isn't a real surprise to me! Sometimes I can get good results by changing the channel to something like 3 or 8, but it's usually temporary as the others use Auto Channel and hop around. Now, the router I have is capable of 5.0Ghz, as is the laptop I type this on. Switching to 5.0Ghz gives superb results: I can download at ~90Mbps and get consistent 1ms pings. The problem is that only this laptop supports 5.0Ghz! My question: Would I still get decent 5.0Ghz performance if I place a 2.4Ghz access point directly next to my router? And, indeed, will 2.4Ghz continue working as 'normal'? Testing would be an obvious step, but I threw all my superfluous equipment out in a recent house move. My understanding is that I should get good performance, certainly in comparison to having two devices using the same frequency range, but I do believe there will be some impact by the virtue of them being directly next to each other. (Cabling is not an option due to it being a rented house)

  Read the article

• Can Internet data be used by malware when PC off?

  - by Val

  I have noticed over the last month that my off peak data has been used at a rate of approx 350MB per hour - this has meant that I have gone over my quota and slowed down by my ISP to 256k. There is no one in the house using it (2am-8am is my ISPs off peak hours) at that time. My PC and other wireless devices (ipad and iphone) are turned off. I have changed the wireless password on my modem 3 times and it is now 30 digits long. So I don't think someone else is using my wireless access between 2-8am. It has been suggested by my ISP that I may have malware/spyware on my computer. Sorry for my ignorance, but can malware still run if the PC is off? I did look at my modem's log and followed an IP address to a service called Amazon Simple server Storage. Could this company possibly be the culprit? I am not too tech savvy, so any assistance appreciated. I have run a barrage of spyware cleaning software eg malware bytes; spy bot etc.... Cheers Val

  Read the article

• Ubuntu 12.10, Unity, AMD 12.11 beta drivers, AMD APP SDK 2.7 and OpenCL detection of multiple gpus

  - by junkie

  I'm using Ubuntu 12.10, AMD 12.11 beta drivers, AMD APP SDK 2.7 and OpenCL. I have three amd radeon 7990s plugged in each of which are a dual 7970 so I have six gpus altogether. I plan to go up to eight in a few days. Windows couldn't use even 4 but linux works fine with 6 so far. The strange thing is that the six gpus are only detected by OpenCL in unity (the ubuntu default window manager). If I switch to e17, blackbox or fluxbox or anything else for that matter OpenCL only detects one. I'm using a simple OpenCL program to list all devices to check. I've also checked the output of aticonfig --list-adapters, fglxinfo and clinfo. The first two always show six in all window managers wheras clinfo shows 6 in unity but 1 gpu in all other WMs. I'm also using an X config generated by aticonfig --initial -f --adapter=all. I'm also only using one monitor. I've also checked using lsmod that the fglrx module is loaded in all WMs. So I have two questions. Why does OpenCL see six gpus only in unity? How can I enable six gpus on other lightweight WMs? Basically I'm getting at what determines how many gpus the OpenCL runtime sees? Thanks.

  Read the article

• Port 5357 TCP on Windows 7 professional 64 bit?

  - by Registered

  Is there a reason this port is open, a quick Nmap scan and Nessus scan reveal it's open, why? Are there any ramifications if I close this port via the firewall rule set? Or does anyone here now more info about this port besides Google? WTF? 1)http://www.symantec.com/connect/blogs/who-left-tunnel-door-open-windows-firewall-vista-0 I know the talk is about Vista, but I am pretty sure it's the same port on 7, also. 2)Port 5357 common errors:The port is vulnerable to info leak problems allowing it to be accessed remotely by malicious authors. (Web Services for Devices) I am blocking this crap, if I have issues will just re-enable. Damn windows. Inbound rule for Network Discovery to allow WSDAPI Events via Function Discovery. [TCP 5357] You just got blocked, until I break something, will see. Time to re-Nmap and re-Nessus. Nmap scan 0 open ports after closing Port 5357,Win7 still works for now, one more scan with Nessus just to make sure all is well.

  Read the article

• Is execution of sync(8) still required before shutting down linux?

  - by Amos Shapira

  I still see people recommend use of "sync; sync; sync; sleep 30; halt" incantations when talking about shutting down or rebooting Linux. I've been running Linux since its inception and although this was the recommended procedure in the BSD 4.2/4.3 and SunOS 4 days, I can't recall that I had to do that for at least the last ten years, during which I probably went through shutdown/reboot of Linux maybe thousands of times. I suspect that this is an anachronism since the days that the kernel couldn't unmount and sync the root filesystem and other critical filesystems required even during single-user mode (e.g. /tmp), and therefore it was necessary to tell it explicitly to flush as much data as it can to disk. These days, without finding the relevant code in the kernel source yet (digging through http://lxr.linux.no and google), I suspect that the kernel is smart enough to cleanly unmount even the root filesystem and the filesystem is smart enough to effectively do a sync(2) before unmounting itself during a normal "shutdown"/"reboot"/"poweorff". The "sync; sync; sync" is only necessary in extreme cases where the filesystem won't unmount cleanly (e.g. physical disk failure) or the system is in a state that only forcing a direct reboot(8) will get it out of its freeze (e.g. the load is too high to let it schedule the shutdown command). I also never do the "sync" procedure before unmounting removable devices, and never hit a problem. Another example - Xen allows the DomU to be sent a "shutdown" command from the Dom0, this is considered a "clean shutdown" without anyone having to login and type the magical "sync; sync; sync" first. Am I right or was I lucky for a few thousands of system shutdowns?

  Read the article

• external drive and CentOS - Reset high speed USB device number

  - by Phil

  I have 2 external drives (3TB) and both will not work with my centOS Box. Tested them in windows ( different machine ) No problems ( 2.6.32-279.9.1.el6.i686 ) dmesg reports: usb 2-2: new high speed USB device number 3 using ehci_hcd usb 2-2: New USB device found, idVendor=2109, idProduct=0700 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-2: Product: USB 3.0 SATA Bridge usb 2-2: Manufacturer: VIA Labs, Inc. usb 2-2: SerialNumber: 0000000000006121 usb 2-2: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access ST3000DM 001-9YN166 CC4B PQ: 0 ANSI: 2 sd 6:0:0:0: Attached scsi generic sg3 type 0 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] 5860533165 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 06 00 00 sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sdd: sdd1 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Attached SCSI disk Tyring to use cfdisk / fdisk / gdisk or even fdisk -l results in the program hanging and dmesg reports: usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd I have the same 2 drives physically installed in the computer via SATA Any Ideas?

  Read the article

• Connecting multiple access points

  - by mohsen farahanipoor

  I'm working on a big project. We want to create a wireless network throughout the building with 15 floors. My idea is that we should set up one unified wireless access point at least in each floor...in case of signal attenuate, we use Access point extender/repeater. I selected DWL-6600AP from among D-Link industrial access points. I want to implement a single wireless LAN throughout the building. Is it possible to combines multiple DWL-6600 access points to achieving just a single WLAN? Can a wireless switch controller do this task? Can these Access Points interfere with each other? What is the solution? I read D-Link website's learning materials, but I am still confused. My other question is around the connecting these APs to Wireless Switch Controller - Is it possible to use power line for connecting DWL-6600 to Wireless Switch Controller device? My main goal is that clients with portable devices such as laptops should be easily connected to the network to share & have communication without any more manual configuration as they are already connected to a single network.

  Read the article

• Getting rid of your server in a small business environment

  - by andygeers

  In a small business environment, is it still necessary to have a central server? Speaking for my own company (a small charity with about 12 employees) we use our server (Windows Server 2003) for the following: Email via Microsoft Exchange Central storage Acting as a print server User authentication / Active Directory There are significant costs associated with running a server like this: Electricity, first for the server itself then for the air conditioning required (this thing pumps out a lot of heat) Noise (of which there is a lot) IT support bills (both Windows Server and Exchange are pretty complicated, and there are many ways they can go wrong) I've found ways to replace many of these functions with cheaper (better?) alternatives: Google Apps / GMail is a clear win for us: we have so many spam related problems it's not even funny, and Outlook is dog slow on our aging computers You can buy networked storage devices with built in print servers, such as the Netgear ReadyNAS™ RND4210 that would allow us to store/share all of our documents, and allow us to access printers over the network The only thing that I can't figure out how to do away with is the authentication side of things - it seems to me that if we got rid of our server, you'd essentially have a bunch of independent PCs that had no shared pool of user accounts / no central administrator. Is that right? Does that matter? Am I missing any other good reasons to keep a central server? Does anybody know of any good, cost-effective ways of achieving the same end but without the expensive central server?

  Read the article

• Windows 7 BSOD on startup

  - by Cristy

  I got a BSOD today after getting home from 11 hours of work... It seems to work in SAFE MODE (sometimes, not always) The BSOD says: SYSTEM_SERVICE_EXCEPTION STOP: 0x0000003b WimFsf.sys - Address FFFFF88001A6B76B base at FFFFF88001A600000, DateStamp 4a5bc362. Sometimes it shows the welcome screen, shows the destkop for a few seconds and then BSODs Already did: unplugged all the USB devices reset the CMOS I haven't installed any new software recently. What should I do? EDIT: I've managed to get into safe mode and it seems to works fine. When I go into normal mode it shows the desktop then it freezes... Is it more likely to be a software or hardware problem? EDIT2: I've managed to get into normal mode by disabling all the non-microsoft services & startup programs. One more thing: When I shut down my PC, on the "Logging off" screen appear some artifacts. I don't think it's because of my graphics card cause I've opened Black OPS and it worked fine. It's so strange... It still BSODS on startup (but there a ~=10% that it will not), and when it doesn't BSOD's it works fine...

  Read the article

• wireless router - configuring for low-latency, high traffic environment

  - by Mark C

  Hey all, I have a few questions about configuring a router to achieve low-latency, high speed throughput on a local area network that is not connected to the internet. I've read up on some stuff, but thought I would solicit some opinions here on what I've found and what I want to know.... Turn off SSID broadcast - it produces extraneous packets that all clients receive and reply (?) to. Not a huge deal, but it may help a bit. Mixed-mode off - I should attempt to have all devices using the same standard (e.g. 802.11n) and turn mixed-mode off. Any thoughts on security? Does having WEP or any of the WPA variants actually increase latency? Nothing super secure is going over this LAN so if turning security off made things better, that'd be cool. Any other thoughts or things to focus on to create the low latency environment I'm trying to go for would be great. Links to webpages and papers are also cool. I'm open to go through a bunch of stuff. Thanks in advance!

  Read the article

• Linux wireless disconnect every 20 minutes

  - by james

  My laptop uses CentOS 6.3 with kernel 2.6.32-279.el6.x86_64. My wireless adaptor is Intel Corporation Centrino Wireless-N 1000. My wireless connection always get off after about 20 minutes. The network applet shows the connection is still on with good signal strength, but I just cannot load any web pages even the configuration page of the wireless router. The problem will continue until I disable and reconnect the wireless. Other devices like my cell phone uses the same wireless network without the problem. Even yesterday I'm using the same laptop with Fedora 17 without this problem. I also searched the internet and someone said running services NetworkManager and network simultaneously may be a problem. But I cannot stop any one of them because: if I stop network and start NetworkManager, the network service will start automatically; if I stop NetworkManager and run network, it says "Device does not seem to be present, delaying initialization." when trying to bringing on the wireless. What shall I do to get rid of the problem? Thank you very much!

  Read the article

• HP Photosmart C4780 printer/scanner breaks netgear WNDR3700v3 router on connection

  - by CodeJunkie

  A few months ago, we upgraded our Netgear router's firmware. Immediately, we started having trouble connecting to the internet. Each time this problem would happen, every device in the house would stop being able to make new connections to the internet. For example, you couldn't open new pages in the browser, but if Skype was running when the problem happened, you could keep talking to people. The only solution to this problem seemed to be resetting the router to factory defaults. Eventually, we solved this problem by just downgrading the router firmware. A while later, we got a new Netgear router. Almost right away, the new router started having exactly the same problems as the old one did on current firmware. The network connection would stay active and the computer would say it had an internet connection, but you couldn't do anything online except for using Skype. We eventually figured out that this happens every time our HP printer gets onto the network. Any time the printer gets onto the wireless network, the whole network stops connecting to the internet almost completely. The only thing that will fix it at that point is to reset the router to factory specs, and unplug the printer so it can't get back onto the network. The Netgear router has the latest version of the firmware, but the printer/scanner is very old. It looks to me like this problem is probably a result of a firmware conflict between the printer and the router, but I'm not sure how to fix that problem. Here's some additional information: Printer: HP Photosmart C4780 Router: WNDR3700v3 Router firmware: V1.0.0.22_1.0.17 (Stock, up to date firmware) Why would the printer getting on the network cause the router to not be able to access the internet correctly until it was reset? What can be done to allow the printer to be on the network without breaking the network for all other devices? Edit: One other thing that happens during this internet problem is that multiple computers in the house display an "IP conflict" message repeatedly, and extremely frequently (as often as every five to ten minutes, and every time a connection to the wireless is made).

  Read the article

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• How do I mount an external USB hard drive on my Sheevaplug?

  - by James

  I've acquired a Sheevaplug running - I think - Ubuntu. I'd like to mount an external USB hard drive, but I don't know the name of the device that needs mounting. When I list the devices under /dev, a long list is produced. How do I find out which device listed needs to be mounted? Update: When I run dmesg after plugging the device in, I see the following at the end: usb 1-1: new high speed USB device using ehci_marvell and address 6 usb 1-1: device not accepting address 6, error -71 usb 1-1: new high speed USB device using ehci_marvell and address 7 usb 1-1: device not accepting address 7, error -71 usb 1-1: new high speed USB device using ehci_marvell and address 8 usb 1-1: device not accepting address 8, error -71 usb 1-1: new high speed USB device using ehci_marvell and address 9 usb 1-1: device not accepting address 9, error -71 And when I view /var/log/messages, I can see this: Sep 23 21:26:03 debian kernel: usb 1-1: new high speed USB device using ehci_ma$ Sep 23 21:26:04 debian kernel: usb 1-1: new high speed USB device using ehci_ma$ Sep 23 21:26:05 debian kernel: usb 1-1: new high speed USB device using ehci_ma$ Sep 23 21:26:05 debian kernel: usb 1-1: new high speed USB device using ehci_ma$ Unfortunately, I don't know what these mean.

  Read the article

• How to configure a Linux kernel based on the modules currently in use?

  - by Carla

  Hello, I'm willing to build a minimal kernel with only the needed things for my machine; so I started by compiling the kernel from the ground up, using the default configuration and adding things that I know for sure I have (i.e.: Ethernet card, WiFi card, ...). But there are several other things not so easy to know about (i.e.: the watchdog timer) so I came across AutoKernConf which supposedly detects the hardware of the machine and generates a kernel configuration file with the settings for the found devices. The problem is it contained several settings repeated and even some which I don't have (I'm using a Dell laptop and one of the things it "found" was something of a Toshiba one). So I ended up building a kernel with the configuration that came out of the make allmodconfig command, which is a kernel with most of the things compiled as modules. Booting into that kernel and running lsmod I can see all of the kernel modules in use (the ones really needed) and I would like to know if there is a tool or some way for me to parse that list and convert it to the corresponding kernel configuration file. Or how to map each one with the appropriate options in the kernel so that I can manually set them. Thank you very much for your time.

  Read the article

• Extending a home wireless network using two routers running tomato

  - by jalperin

  I have two Asus RT-N16 routers each flashed with Tomato (actually Tomato USB). UPSTAIRS: Router 'A' (located upstairs) is connected to the internet via the WAN port and connected via a LAN port to a 10/100/1000 switch (Switch A). Several desktops are also attached to Switch A. Router A uses IP 192.168.1.1. DOWNSTAIRS: I've just acquired Router 'B' and set it to IP 192.168.1.2. I have a cable running from Switch A downstairs to another switch (Switch B). Tivo, a blu-ray player and a Mac are connected to Switch B. My plan was to connect Router B to Switch B so that I have improved wireless access downstairs. (The wireless signal from Router A gets weak downstairs in a number of locations.) How should I configure Router B so that all devices in the house can see and talk to one another? I know that I need to change DHCP on Router B so that it doesn't cover the same range as DHCP on Router A. Should I be using WDS on the two routers, or is that unnecessary since I already have a wired connection between the two routers? Any other thoughts or suggestions? Thanks! --Jeff

  Read the article

< Previous Page | 356 357 358 359 360 361 362 363 364 365 366 367  | Next Page >