Search Results

Search found 41598 results on 1664 pages for 'segmentation fault'.

Page 361/1664 | < Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either. EDIT: Adding arp output: C:\Users\Srekel>arp -a Interface: 192.168.1.7 --- 0xd Internet Address Physical Address Type 192.168.1.1 00-1f-33-ef-28-01 dynamic 192.168.1.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Adding ipconfig... C:\Users\Srekel>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Kakburken4 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TP-LINK Wireless N Adapter Physical Address. . . . . . . . . : 00-25-86-DF-C6-89 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 09 April 2010 23:09:45 Lease Expires . . . . . . . . . . : 10 April 2010 23:09:45 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller #2 Physical Address. . . . . . . . . : E0-CB-4E-26-B9-84 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : E0-CB-4E-26-BE-94 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{74D5C406-894E-4000-8DE7-6AAEBF7C8382}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2001:0:5ef5:73ba:881:20c1:3f57:fef8(Preferred) Link-local IPv6 Address . . . . . : fe80::881:20c1:3f57:fef8%14(Preferred) Default Gateway . . . . . . . . . : :: NetBIOS over Tcpip. . . . . . . . : Disabled

  Read the article

• Caching without file extensions

  - by Sigurs

  I'm trying to use Varnish to show the non-logged in users a cached version of my website. I'm able to perfectly detect if the user is logged in or out, but I can't cache pages without extensions. There is no file extension because nginx is rewriting the URL to a php script(so caching .php does not work). For example I'd like varnish to cache: example.com example.com/forum/ example.com/contact/ I have tried if (req.request == "GET" && req.url ~ "^/") { return(lookup); } if (req.request == "GET" && req.url ~ "") { return(lookup); } if (req.request == "GET" && req.url ~ "/") { return(lookup); } but nothing seems to work... any help?

  Read the article

• Proper network configuration for a KVM guest to be on the same networks at the host

  - by Steve Madsen

  I am running a Debian Linux server on Lenny. Within it, I am running another Lenny instance using KVM. Both servers are externally available, with public IPs, as well as a second interface with private IPs for the LAN. Everything works fine, except the VM sees all network traffic as originating from the host server. I suspect this might have something to do with the iptables-based firewall I'm running on the host. What I'd like to figure out is: how to I properly configure the host's networking such that all of these requirements are met? Both host and VMs have 2 network interfaces (public and private). Both host and VMs can be independently firewalled. Ideally, VM traffic does not have to traverse the host firewall. VMs see real remote IP addresses, not the host's. Currently, the host's network interfaces are configured as bridges. eth0 and eth1 do not have IP addresses assigned to them, but br0 and br1 do. /etc/network/interfaces on the host: # The primary network interface auto br1 iface br1 inet static address 24.123.138.34 netmask 255.255.255.248 network 24.123.138.32 broadcast 24.123.138.39 gateway 24.123.138.33 bridge_ports eth1 bridge_stp off auto br1:0 iface br1:0 inet static address 24.123.138.36 netmask 255.255.255.248 network 24.123.138.32 broadcast 24.123.138.39 # Internal network auto br0 iface br0 inet static address 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 bridge_ports eth0 bridge_stp off This is the libvirt/qemu configuration file for the VM: <domain type='kvm'> <name>apps</name> <uuid>636b6620-0949-bc88-3197-37153b88772e</uuid> <memory>393216</memory> <currentMemory>393216</currentMemory> <vcpu>1</vcpu> <os> <type arch='i686' machine='pc'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='cdrom'> <target dev='hdc' bus='ide'/> <readonly/> </disk> <disk type='file' device='disk'> <source file='/raid/kvm-images/apps.qcow2'/> <target dev='vda' bus='virtio'/> </disk> <interface type='bridge'> <mac address='54:52:00:27:5e:02'/> <source bridge='br0'/> <model type='virtio'/> </interface> <interface type='bridge'> <mac address='54:52:00:40:cc:7f'/> <source bridge='br1'/> <model type='virtio'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' keymap='en-us'/> </devices> </domain> Along with the rest of my firewall rules, the firewalling script includes this command to pass packets destined for a KVM guest: # Allow bridged packets to pass (for KVM guests). iptables -A FORWARD -m physdev --physdev-is-bridged -j ACCEPT (Not applicable to this question, but a side-effect of my bridging configuration appears to be that I can't ever shut down cleanly. The kernel eventually tells me "unregister_netdevice: waiting for br1 to become free" and I have to hard reset the system. Maybe a sign I've done something dumb?)

  Read the article

• Allowing connections initiated from outside

  - by Mark S. Rasmussen

  I've got an old Juniper SSG5 running ScreenOS 5.4.0r6.0. Once a day, more or less, it'll start randomly dropping packets at a rate of ~5-10%. We currently solve this issue by simply rebooting the unit, after which it resumes working in perfect condition. As this error has started appearing randomly, without any configuration or hardware changes, I'm assuming I've got an aging unit about to fail. As such, I've got a replacement SSG5 running ScreenOS 6.0. I've dumped the config on the 5.4 and imported it into a clean 6.0, and it seems to gladly accept it, and all my configuration seems to be A-OK. However, upon connecting the new unit, all outside-initiated connections seem to be blocked. If I browse our external IP from the inside, everything works perfectly, and it's not just port 80, SSH, Crashplan - all of our policies route correctly. All normal networking, initiated from the inside, work perfectly as well. If on the other hand I browse our external IP from the outside, everything is blocked. Barring differences between ScreenOS 5.4 and 6.0, the config is identical. Is there a setting somewhere that defines whether outside/inside initiated connections are allowed? unset key protection enable set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "XXX" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 215.173.182.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 215.173.182.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 215.173.182.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 215.173.182.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname companyalan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname companyblan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 215.173.182.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set pki x509 dn name "[email protected]" set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set vrouter "untrust-vr" exit set vrouter "trust-vr" exit set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "HTTP" permit log set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(215.173.182.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit Note that I've previously posted a similar question (pertaining to the same device & replacement, but ultimately caused by a malfunctioning switch, and thus clouding the current issue): Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  Read the article

• How can I proxy couchDB as a sub-diectory with lighttpd?

  - by indieinvader

  I have a sub-directory on my web server (lighttpd) that I want to point at a CouchDB instance running on the same machine. I tried using mod_proxy but it sends along the whole request, like a proxy should, I know! So: // What happens: Lighttpd: http://localhost/couchdb/some_request | V CouchDB: http://localhost:5984/couchdb/some_request // What I want to happen: Lighttpd: http://localhost/couchdb/some_request | V CouchDB: http://localhost:5984/some_request Is there any way to make this setup work?

  Read the article

• System monitoring tool via command line in Windows

  - by Anders

  Hi all, Is there a command line tool for Windows XP to display system resources, like available memory usage, cpu, diskspace etc... Small and requires a non-install. Best Regards, Anders

  Read the article

• 401 - Unauthorized: Access is denied error from web app running in IIS 7.5 using App Pool Identity

  - by Eric Gatesman

  I have an ASP.NET app on a Windows 2008 server, IIS 7.5. When I try to access web site, I get a login popup. If I click "cancel" I get a 401 - Unauthorized: Access is denied due to invalid credentials. The app is using Windows authentication (anonymous is disabled). The app has it's own app pool, running under the App Pool Identity. If I change the app pool to run under the NetworkService account, my website functions just fine. I'm guessing that this is just a permissions issue, but can't figure out what permissions I need to change. I gave the App Pool Identity permissions on the physical directory of the app, but that didn't solve the problem.

  Read the article

• VirtualBox - Public Static IP for a Debian Guest on a Dedicated Server

  - by user86296

  Goal: I want to run a Debian-squeeze-Guest in VirtualBox and it's own public static ip. I found tons of threads about this topic, but all in all I'm now trying for 10 hours (reading the manual, the forums, trying to learn about networking concepts & commands) to give a Guest his own public static ip (so that the Guest is similar to a vServer you can order from a hosting company), but wasn't able to. Since I'm a big noob as far as networking stuff is concerned, I'm probably doing something wrong.(please bear with me :-) ) Situation: VirtualBox 4.0.10 (headless no gui) is running on a dedicated Debian-Server, the Guest OS is Debian as well. The server has a static ip and I ordered an additional ip for a VM. Problem description: Upto now I was able to use NAT to access the VM from the outside and to setup an internal network between several Guests and all of this worked very well. When setting NIC 1 to bridged and configuring a public static ip on the guest, the guest was unpingable. (neither from outside, nor from the host) I could connect to the guest via the internal network, from another vm, though. ( VBoxManage controlvm VMGuest nic1 bridged eth0 ) ( configuration attempt of static-ip on the guest '/etc/network/interfaces' is below) Please let me know what I'm doing wrong, or what I can try to get it to work, or if you need more info. I think I've read that with a current VirtualBox-version for bridged networking no special host-configuration is necessary, is that accurate, or might that be the problem? Additional Info Info I got from the hosting company about the additional IP Please note that you can use the IP address only for this server. IP: 46.4.xx.xx Gateway: 46.4.xx.xx Mask: 255.255.255.248 VBoxManage showvminfo VMGuest |less ... NIC 1: MAC: 080027D72F7B, Attachment: Bridged Interface 'eth0', Cable connected: on, Trace: off (file: none), Type: 82540EM, Reported speed: 0 Mbps, Boot priority: 0 NIC 2: MAC: 080027B03B75, Attachment: Internal Network 'InternalNet1', Cable connected: on, Trace: off (file: none), Type: Am79C973, Reported speed: 0 Mbps, Boot priority: 0 NIC 3: disabled (...rest is disabled) cat /etc/network/interfaces on the Host-machine # Loopback device: auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 46.4.xx.xx broadcast 46.4.xx.xx netmask 255.255.255.224 gateway 46.4.xx.xx post-up mii-tool -F 100baseTx-FD eth0 # default route to access subnet up route add -net 46.4.xx.xx netmask 255.255.255.224 gw 46.4.xx.xx eth0 cat /etc/network/interfaces on the Guest-VM # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 46.4.xx.xx netmask 255.255.255.248 gateway 46.4.xx.xx auto eth1 iface eth1 inet dhcp ifconfig -a on the Guest shows the correct static ip for eth0 but the Guest is unreachable "over eth0" eth0 Link encap:Ethernet HWaddr 08:00:27:d7:2f:7b inet addr:46.4.xx.xx Bcast:46.4.xx.xx Mask:255.255.255.248 inet6 addr: fe80::a00:27ff:fed7:2f7b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:21 errors:0 dropped:0 overruns:0 frame:0 TX packets:69 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1260 (1.2 KiB) TX bytes:3114 (3.0 KiB) eth1 Link encap:Ethernet HWaddr 08:00:27:b0:3b:75 inet addr:192.168.10.3 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:feb0:3b75/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:142 errors:0 dropped:0 overruns:0 frame:0 TX packets:92 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15962 (15.5 KiB) TX bytes:14540 (14.1 KiB) Interrupt:16 Base address:0xd240 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:123 errors:0 dropped:0 overruns:0 frame:0 TX packets:123 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25156 (24.5 KiB) TX bytes:25156 (24.5 KiB)

  Read the article

• What does "link to unknown" mean?

  - by Question Overflow

  I just upgraded my server to Fedora 17 which made a switch of my bootloader from GRUB Legacy to GRUB2. There are two symbolic links in the /etc folder that points to the files grub.conf and grub.cfg in /boot/grub and /boot/grub2 respectively. Though the targets seem correct, the link icons are displaying an X status which seems to indicate that the links are broken. Upon right-clicking the property type, it states "link to unknown". The file size of the link corresponds exactly with the file size of the target file, so, why does the links appear to be broken? The image of the link icons: As requested, the following are the outputs from the commands: $ ls -l /etc/grub.conf lrwxrwxrwx. 1 root root 22 Jul 14 2011 /etc/grub.conf -> ../boot/grub/grub.conf $ ls -l /etc/grub2.cfg lrwxrwxrwx. 1 root root 22 Dec 10 18:57 /etc/grub2.cfg -> ../boot/grub2/grub.cfg

  Read the article

• can't get php mail() working on Ubuntu desktop version with sendmail and postfix

  - by user36428

  I'm running Ubuntu 9.10 LAMP and trying to do a simple email test with PHP and I'm not getting any emails sent. mail("[email protected]", "eric-linux test", "test") or die("can't send mail"); I get no errors from PHP when running that script. In my php.ini file is: sendmail_path = /usr/lib/sendmail -t -i $ sudo ps aux | grep sendmail eric 2486 0.0 0.4 8368 2344 pts/0 T 14:52 0:00 sendmail -s “Hello world” [email protected] eric 8747 0.0 0.3 5692 1616 pts/2 T 16:18 0:00 sendmail eric 8749 0.0 0.3 5692 1636 pts/2 T 16:18 0:00 sendmail start eric 9190 0.0 0.3 5692 1636 pts/2 T 19:12 0:00 sendmail start eric 9192 0.0 0.3 5692 1616 pts/2 T 19:12 0:00 sendmail eric 9425 0.0 0.3 5692 1620 pts/1 T 19:37 0:00 sendmail eric 9427 0.0 0.3 6584 1636 pts/1 T 19:37 0:00 sendmail restart eric 9429 0.0 0.3 5692 1636 pts/1 T 19:38 0:00 /usr/lib/sendmail restart eric 9432 0.0 0.1 3040 804 pts/1 R+ 19:38 0:00 grep --color=auto sendmail When I run $ sendmail start it just hangs there doing nothing. I installed postfix also to see if it would help, but it didn't. I tried to see port 25: eric@eric-linux:~$ telnet localhost 25 Trying ::1... Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 eric-linux ESMTP Postfix (Ubuntu) thanks

  Read the article

• DrayTek Vigor 2920(n): VPN with VLAN restrictions?

  - by Dirk

  Hi, I'm currently installing a DrayTek Vigor 2920n router in a new office. This router is to be used for 2 seperate companies. For one of these companies, the router has a LAN-2-LAN (VPN) connection to a datacenter configured. The other company should not be able to access this other (VPN-)network. I'm aware of the capability of this router to have VLAN's, but I cannot figure out how to configure the VPN-connection to only be accessible for VLAN0 and not for VLAN1. I know I can also add another router to physically split both networks, but we bought the DrayTek with the idea that it could easily have the VPN-connection available for VLAN0 and not for VLAN1. VLAN1 can easily be in another subnet, that's fine, although, I don't know how to configure that on this DrayTek. Can anyone point me in the right direction? Thanks in advance, Dirk

  Read the article

• How to create ftp server on Webmin?

  - by Tom

  Hello firstly, i'm new at vps hosting so i'm not that good at SSH and so on, So i have a vps running centOS 5.4 x64 LAMP ( linux,apache,mysql,php) and i'm really confused because i can't find FTP management or subdomains or even the email address on my webmin panel. Should i install additional modules ? Thanks

  Read the article

• Upgrade MySQL on Plesk on Windows

  - by Cyril Gupta

  I just got a nasty surprise when I installed a website in Unicode Hindi (Indian language) on a server, all freshly entered unicode data is turning into question marks on the server. On my dev machine it works perfectly. I found that I have MySQL version 5.0.45 (installed in default by Plesk I guess). On my dev machine i have version 5.1.33. I believe the problem could be due to the version difference. The new version of MySQL apparently has better support for Unicode than the older one. I want to upgrade MySQL on my Windows Server machine with Plesk installed on it I am reluctant to just install the new version using the mysql installer because Plesk maintains some custom settings for mysql and I am afraid the new version could change those settings and break my db. Can anyone tell me do I have to do anything special to install MySQL on plesk on windows or can I just use the new version installer?

  Read the article

• Intermittent PHP error: Undefined function <core function>

  - by Daniel

  In the last week I've been coming across an incredibly annoying error on one of Slicehost slices. It appears that every now and then PHP will fail with a fatal error, saying a certain function is undefined. The function changes, but is always a core PHP function e.g. defined(), version_compare(), etc. This problem has occurred while using several different PHP applications - PHPMyAdmin, my own custom built apps, etc, leading me to believe that the problem is not specific to the running code. Here are some details: - Debian Lenny - Apache 2.2.9 - PHP 5.2.6-1+lenny4 with Suhosin-Patch (running eAccelerator 0.9.6) Apache and PHP are installed from Debian packages. Error logs show nothing out of the ordinary. I thought memory might be an issue, but free -m reports upwards of 100MB free almost all the time. Another thing I'm trying to investigate is if the problem might be related to eAccelerator, but testing this theory out is incredibly hard because the issue doesn't appear very often and I've been using eAccelerator for months on this install without any problems up until now. Has anyone ever come across anything like this? Why would PHP report undefined core functions?

  Read the article

• Autoloading Development or Production configs (best practices)

  - by Xeoncross

  When programming sites you usually have one set of config files for the development environment and another set for the production server (or one file with both settings). I am assuming all projects should be handled by version control like git or svn. Manual file transfers (like FTP) is wrong on so many levels. How you enable/disable the correct settings (so that your system knows which ones to use) is a problem for me. Each system I work on just kind of jimmy-rigs a solution. Below are the 3 methods I know of and I am hoping that someone can submit a more elegant solutions. 1) File Based The system loads a folder structure based on the URL requested. /site.com /site.fakeTLD /lib index.php For example, if the url is http://site.com then the system loads the production config files located in the site.com folder. However, if I'm working on the site locally I visit http://site.fakeTLD to work on the local copy of the site. To setup this I edit my hosts file and add site.fakeTLD to point to my own computer (127.0.0.1/localhost) and then create a vhost in apache. So now I can work on the codebase locally and then push to the server without any trouble. The problem is that this is susceptible to a "host" injection attack. So someone loading site.com could set the host to site.fakeTLD and then the system would load my development config files instead of production. 2) Config Based The config files contain on section for development - and one for production. The problem is that each time you go to push your changes to the repo you have to edit the file to specify which set of config options should be used. $use = 'production'; //'development'; This leaves the repo open to human error should one of the developers forget to enable the right setting. 3) File System Check Based All the development machines have an extra empty file called "development.txt" or something. Each time the system loads it checks for this file - if found then it knows it is in development mode - if missing then it knows it is in production mode. Since the file is NEVER ADDED to the repo then it will never be pushed (and checked out) on the production machine. However, this just doesn't feel right and causes a slight slow down since all filesystem checks are slow.

  Read the article

• How to "FTP jail" with Pure-FTPD?

  - by Nate

  I asked this a little bit ago, but instead of specifying Pure-FTPD I just said Apache. Per the answer to that question, I'm asking again with "Pure-FTPD" in the title this time. I need to allow someone access to my VPS via FTP, but there are a number of directories that the person must not be allowed to view or modify. For example, something like this: private_info_1 public_info_1 private_info_2 public_info_2 In this example, the FTP user would need to be allowed to do stuff in the public directories, but not the private ones. How do I go about doing this with Pure-FTPD? I have cPanel and SSH access.

  Read the article

• Wiping out user and/or root password in embedded linux

  - by TryTryAgain

  We have a security camera system running an embedded linux. It boots with Lilo as a bootloader and has no tty access once booted. I don't know any username either. SSH/22 is open, but I don't think brute force is an option. I have tried all the common tricks to reset a linux user password (boot from the bootloader in single user mode = doesn't happen, still prompts for user login, boot to a live cd = can't access the file system...it's all loop files and other binary, etc etc), but they are all not possible as it is an embedded linux setup the way it is. Any help/suggestions would be appreciated. Thanks

  Read the article

• Lync 2010, Kamailio, & Trixbox 2.6.23 (Asterisk 1.4)

  - by slashp

  I'm having an issue trying to connect Lync 2010 phone calls with our trixbox PBX. I've gotten to the point where Kamailio seems to be functioning properly and acting as a bridge between TCP traffic (from Lync) & UDP traffic (to the trixbox, as Asterisk 1.4 does not support SIP over TCP). Our Lync box IP: 10.100.10.41 Our Kamailio box IP: 10.100.10.44 Our trixbox IP: 10.100.10.2 The issue I'm running into is as follows when enabling SIP debugging for the Kamailio box: <--- SIP read from 10.100.10.44:5060 ---> PRACK sip:TNECLTSLY01.contoso.com:5068;transport=Tcp;maddr=10.100.10.41 SIP/2.0 FROM: <sip:9121;[email protected];user=phone>;epid=CF2380792B;tag=4852bab430 TO: <sip:[email protected];user=phone>;epid=CF2380792B;tag=3684a6a24e CSEQ: 24 PRACK CALL-ID: 192daae6-00e1-4140-bddd-0394b35d475b MAX-FORWARDS: 70 Via: SIP/2.0/UDP 10.100.10.44;branch=z9hG4bKcydzigwkX;i=d VIA: SIP/2.0/TCP 10.100.10.41:51677;branch=z9hG4bK159fc989 CONTACT: <sip:TNECLTSLY01.contoso.com:5068;transport=Tcp;maddr=10.100.10.41> CONTENT-LENGTH: 0 USER-AGENT: RTCC/4.0.0.0 MediationServer RAck: 1 23 INVITE <-------------> --- (12 headers 0 lines) --- Sending to 10.100.10.44 : 5060 (NAT) <--- Transmitting (NAT) to 10.100.10.44:5060 ---> SIP/2.0 481 Call leg/transaction does not exist Via: SIP/2.0/UDP 10.100.10.44;branch=z9hG4bKcydzigwkX;i=d;received=10.100.10.44 Via: SIP/2.0/TCP 10.100.10.41:51677;branch=z9hG4bK159fc989 From: <sip:9121;[email protected];user=phone>;epid=CF2380792B;tag=4852bab430 To: <sip:[email protected];user=phone>;epid=CF2380792B;tag=3684a6a24e Call-ID: 192daae6-00e1-4140-bddd-0394b35d475b CSeq: 24 PRACK User-Agent: Asterisk PBX Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY Supported: replaces Content-Length: 0 <------------> trixbox1*CLI> <--- SIP read from 10.100.10.44:5060 ---> ACK sip:[email protected];user=phone SIP/2.0 FROM: "John Jones"<sip:9121;[email protected];user=phone>;tag=4852bab430;epid=CF2380792B TO: <sip:[email protected];user=phone>;tag=3684a6a24e;epid=CF2380792B CSEQ: 23 ACK CALL-ID: 192daae6-00e1-4140-bddd-0394b35d475b MAX-FORWARDS: 70 Via: SIP/2.0/UDP 10.100.10.44;branch=z9hG4bKcydzigwkX;i=d VIA: SIP/2.0/TCP 10.100.10.41:51677;branch=z9hG4bK79a21c CONTENT-LENGTH: 0 My SIP trunk on the trixbox looks like this: [from-lync] exten => _+4XXX!,1,Noop(Stripping + from start of number) exten => _+4XXX!,n,Goto(from-internal,${EXTEN:1}) Though I am still having no luck getting the + stripped or the call to go through. Any ideas would be greatly appreciated. Thank you! -slashp

  Read the article

• mrepo and grouplist/groupinstall?, mrepo not working as expected with group

  - by user52874

  All, I'm trying to set up mrepo so we can have internal repositories. After quite the slog, things seem to be working as expected EXCEPT for groups. From man createrepo: EXAMPLES Here is an example of a repository with a groups file. Note that the groups file should be in the same directory as the rpm packages (i.e. /path/to/rpms/comps.xml). createrepo -g comps.xml /path/to/rpms So here's what I'm doing: wget -c http://ftp.scientificlinux.org/linux/scientific/6/x86_64/os/repodata/comps-sl6-x86_64.xml cp comps-sl6-x86_64.xml /var/mrepo/SL6-x86_64/os/Packages/comps-sl6-x86_64.xml createrepo -g comps-sl6-x86_64.xml /var/mrepo/SL6-x86_64/os/Packages/ lots of output, no apparent errors or warnings BUT.. from a client: yum grouplist Loaded plugins: refresh-packagekit Setting up Group Process Error: No group data available for configured repositories Here's /etc/mrepo.conf: ### Configuration file for mrepo ### The [main] section allows to override mrepo's default settings ### The mrepo-example.conf gives an overview of all the possible settings [main] srcdir = /var/mrepo wwwdir = /var/www/mrepo confdir = /etc/mrepo.conf.d arch = x86_64 mailto = root@localhost smtp-server = localhost pxelinux = /usr/lib/syslinux/pxelinux.0 tftpdir = /tftpboot #rhnlogin = username:password ### Any other section is considered a definition for a distribution ### You can put distribution sections in /etc/mrepo.conf.d ### Examples can be found in the documentation. Here's /etc/mrepo.conf.d/sl6.mrepo: ### Scientific Linux 6 [SL6] name = Scientific Linux 6 release = 6 arch = x86_64 metadata = repomd repoview os = rsync://rsync.scientificlinux.org/scientific/$release/$arch/os/ updates = rsync://rsync.scientificlinux.org/scientific/$release/$arch/updates/ security = rsync://rsync.scientificlinux.org/scientific/$release/$arch/updates/security/ fastbugs = rsync://rsync.scientificlinux.org/scientific/$release/$arch/updates/fastbugs/

  Read the article

• /etc/crontab or any user crontab is not being executed

  - by ian

  My server is CentOS 5. When I edit /etc/crontab or edit any user(including root) crontab via "crontab -e" command, it just adds "(system) RELOAD (/etc/crontab)" or "(admin) RELOAD (cron/admin)" in the log. No CMD in the /var/log/cron. Sample entry in /var/log/cron: Aug 10 10:21:33 localhost crontab[31688]: (root) BEGIN EDIT (root) Aug 10 10:21:42 localhost crontab[31688]: (root) REPLACE (root) Aug 10 10:21:42 localhost crontab[31688]: (root) END EDIT (root) Aug 10 10:22:01 localhost crond[2688]: (root) RELOAD (cron/root) Result of "service crond status": crond (pid 1345) is running... The command "cat /var/log/messages | grep cron" does not give anything. Contents of /etc/cron.allow: admin root Contents of /etc/crontab: SHELL=/bin/bash PATH=/sbin:/bin:/usr/sbin:/usr/bin MAILTO=root HOME=/ # run-parts 01 * * * * root run-parts /etc/cron.hourly 02 4 * * * root run-parts /etc/cron.daily 22 4 * * 0 root run-parts /etc/cron.weekly 42 4 1 * * root run-parts /etc/cron.monthly * * * * * root run-parts /bin/date >> /data/date.txt Result of ps aux |grep cron: root 1345 0.0 0.1 5268 1204 ? Ss 11:43 0:00 crond Contents of admin's crontab: * * * * * /bin/date >> /data/date.txt Note that it's not only admin's crontab that's not running. All cron jobs are not running. Any ideas why they aren't running?

  Read the article

• My server freezes within a few hours of logging out. Staying logged in keeps the server running

  - by HappyEngineer

  I have an Ubuntu Godaddy server I use to host mail and webapps. It started having problems a couple months ago. It would lock up and stop responding to anything. I couldn't ssh into it, so I'd have godaddy power cycle the server. I have never seen anything that looked suspicious in the var logs (although I'm no expert at reading them). An fsck turned up no problems. Godaddy replaced the ram, but found no hardware problems. I started logging the output from "top" to a log file and found that even that stops running when the server freezes. Now, here is the crazy part: It got so bad that it would actually go down every few hours, but then it stopped going down. I eventually realized I had left an ssh terminal logged into the machine running top. This seemed unlikely to be a reason, but after the server was up with no problems for a full week (remember, it had been going down after just a few hours), I disconnected from the ssh session. Lo and behold, within a few hours the server froze again! I had them power cycle again and then left another ssh session open with top. It has been going without problems for 8 days now. I told others about this and they hardly believe me. I simply can't imagine what is going on. I don't know what else to try other than to just get a new server and reinstall everything. Does anyone have any ideas about what I can look for to determine what the cause is? Is it possible there's some sort of exploit on the server which only runs if everyone is logged out of the system? EDIT: The power management gone haywire sounds plausible, so I've modified the /boot/grub/menu.lst to boot with acpi=off and apm=off. It appears to have prevented kacpid and kacpid_notify from being in the process list, so I assume I did that right. I've disconnected all my sessions from the server. I'll check later tonight to see if it's still up. If it goes down then I'll try the pinging process idea. EDIT: It went down again. It lasted about a day. I've had them reboot, so now I'll try running "nohup ping -i 5 google.com &" and then disconnect. If it goes down again I'll come back. Hopefully someone will have some more ideas.

  Read the article

• svn: Syncing main source code with committed source code

  - by alam

  To manage my source code I have created SVN subversion server by using command svnadmin create /myrepos svn import /root/MySourceCode file:///myrepos I have created user and provided rw access to him. User can easily commit their changes in repository. How can I update my sourcecode (/root/MySourceCode) used in command svn import ? Is there any svn command to update my MySourceCode with commited code?

  Read the article

• yum remove doesn't remove things completely ?

  - by Shrinath

  I am trying to remove apache completely from my server,which is a ec2 instance, running Amazonian linux v2.6xx. Lets assume I have a file in /etc/httpd/conf/xyz.txt I am using the following code : yum remove httpd when I try to cd /etc/httpd I get "there is no such directory" error. Next, if I install httpd again, using this : yum install httpd, and then if I look in /etc/httpd/conf/ I still have that file as it is.. untouched.. How is this possible ? How do I "Clean" this ?

  Read the article

• Useful extensions for MediaWiki

  - by Stan

  Can anyone suggestion some useful MediaWiki extension? I've installed PDF export, syntax lighlight, file link protocol, submit in toolbar, enforce strong password. But still eager to know any good/handy extensions. Thanks

  Read the article

• MySQL: creating a user that can connect from multiple hosts

  - by DrStalker

  I'm using MySQL and I need to create an account that can connect from either the localhost of from another server, 10.1.1.1. So I am doing: CREATE USER 'bob'@'localhost' IDENTIFIED BY 'password123'; CREATE USER 'bob'@'10.1.1.1 IDENTIFIED BY 'password123'; GRANT SELECT, INSERT, UPDATE, DELETE on MyDatabse.* to 'bob'@'localhost', 'bob'@'10.1.1.1; This works fine, but is there any more elegant way to create a user account that is linked to multiple IPs or does it need to be done this way? My main worry is that in the future permissions will be updated form 'bob' account and not the other.

  Read the article

< Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >