Search Results

Search found 25391 results on 1016 pages for 'update notification'.

Page 367/1016 | < Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >

• Ethernet cable unplugged after updating from windows 8.0 to 8.1

  - by Pehmolelu

  Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

  Read the article

• How to make Microsoft JVM work on Windows 7?

  - by rics

  I am struggling with the following problem. I cannot install MS JVM 3810 properly on Windows 7. When I start Interner Explorer 8 without starting any java 1.1 programs choosing Java custom settings under Internet options causes the crash of the browser. I have some Java 1.1 programs that work well in Internet Explorer 8 on Windows XP after the installation of MS JVM 3810. I know that it is not advised to use this old JVM but it is not a short-term option to port the programs in newer Java since it contains 3rd party components. Complete rewrite is a long-term plan. Strangely jview and appletviewer (jview /a) works from a console so the MS JVM 3810 is not completely busted just IE 8 does not like it. The problem with the appletviewer is that it cannot connect to the server even if both signed and unsigned content in Java custom settings have been set to Enable all. (Since Java custom settings was unreachable due to the crash the modifications - including My computer - were performed through the registry and pre-checked to behave correctly on Windows XP and Internet Explorer 8.) If jview was working then I could at least think of a workaround. Is there a way to configure MS JVM or jview properly on Windows 7? Another options would be: Checking Internet Explorer 9 Beta. Using virtualbox and Windows XP older IE in it. Delaying Windows 7 upgrade. ... Update Finally we have modified all the programs to work parallelly as applet and application as well. This way the programs can still be used from browser on older Windows versions. On Windows 7 the applications are started from the desktop. Installation to all user machine can easily be solved since they already have a large common application drive. The code update is fortunately only a few lines of modification: including a main method in the applet class. Furthermore instead of the starting html page a bat file is used to set the classpath before the startup with jview.

  Read the article

• Cron job checking for changes in Git repository

  - by HNygard

  We have just moved our server configs to a Git repository. Therefore there should not be any changes in any of the repository folders. I was thinking about how I could set up a cron job to check for any uncommited changes. How could a cron job be set up to check for changes in a Git repository? Greping the output of the git status command might just do it. Grep and cron jobs are not my strong side. Here are some sample outputs from git status: Standing the folder containing the git repository (e.g. /path/gitrepo/) with changed files: $ git status # On branch master # Changes not staged for commit: # (use "git add <file>..." to update what will be committed) # (use "git checkout -- <file>..." to discard changes in working directory) # # modified: apache2/sites-enabled/000-default # # Untracked files: # (use "git add <file>..." to include in what will be committed) # # apache2/conf.d/test no changes added to commit (use "git add" and/or "git commit -a") Standing in the folder when there is no changes: $ git status # On branch master nothing to commit (working directory clean) Update: Synced up with origin is not important. There should be no local changes. Local files that must be in place go into the .gitignore file. In addition to the server configs there are also git repos for content (static web sites, web apps, wordpress, etc). None of the repositories should have local changes. We might use Puppet in the long run since its being used for development of one of the web apps.

  Read the article

• How to delete removed devices from a mdadm RAID1?

  - by Kabuto

  I had to replace two hard drives in my RAID1. After adding the two new partitions the old ones are still showing up as removed while the new ones are only added as spare. I've had no luck removing the partitions marked as removed. Here's the RAID in question. Note the two devices (0 and 1) with state removed. $ mdadm --detail /dev/md1 mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. /dev/md1: Version : 00.90 Creation Time : Thu May 20 12:32:25 2010 Raid Level : raid1 Array Size : 1454645504 (1387.26 GiB 1489.56 GB) Used Dev Size : 1454645504 (1387.26 GiB 1489.56 GB) Raid Devices : 3 Total Devices : 3 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 12 21:30:39 2013 State : clean, degraded Active Devices : 1 Working Devices : 3 Failed Devices : 0 Spare Devices : 2 UUID : 10d7d9be:a8a50b8e:788182fa:2238f1e4 Events : 0.8717546 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 8 34 2 active sync /dev/sdc2 3 8 18 - spare /dev/sdb2 4 8 2 - spare /dev/sda2 How do I get rid of these devices and add the new partitions as active RAID devices? Update I seem to have gotten rid of them. My RAID is resyncing, but the two drives are still marked as spares and are number 3 and 4, which looks wrong. I'll have to wait for the resync to finish. All I did was to fix the metadata error by editing my mdadm.conf and rebooting. I tried rebooting before, but this time it worked for whatever reason. Number Major Minor RaidDevice State 3 8 2 0 spare rebuilding /dev/sda2 4 8 18 1 spare rebuilding /dev/sdb2 2 8 34 2 active sync /dev/sdc2

  Read the article

• Forward e-mail to multiple addresses with conditions

  - by Valera Leontyev

  I need to forward e-mails to different mail accounts by different conditions. The aim is to create mail notification scheme for my company. I'd like to setup server on dedicated mail domain for it. Is there any software that helps to get my aim (Linux)? Examples: 1) forward all e-mail sent to [email protected] to x@x, y@y, z@z (no conditions) 2) forward e-mail sent to [email protected] where subject contains '[finance]' to a@b and b@b 3) forward e-mail sent to [email protected] where subject contains '[fault]' to s@s and s2@s. Receivers' domains are different. P.S. Now we use Gmail filters to get this functionality, but it's unstable and hard to maintain.

  Read the article

• Mysql: create index on 1.4 billion records

  - by SiLent SoNG

  I have a table with 1.4 billion records. The table structure is as follows: CREATE TABLE text_page ( text VARCHAR(255), page_id INT UNSIGNED ) ENGINE=MYISAM DEFAULT CHARSET=ascii The requirement is to create an index over the column text. The table size is about 34G. I have tried to create the index by the following statement: ALTER TABLE text_page ADD KEY ix_text (text) After 10 hours' waiting I finally give up this approach. Is there any workable solution on this problem? UPDATE: the table is unlikely to be updated or inserted or deleted. The reason why to create index on the column text is because this kind of sql query would be frequently executed: SELECT page_id FROM text_page WHERE text = ? UPDATE: I have solved the problem by partitioning the table. The table is partitioned into 40 pieces on column text. Then creating index on the table takes about 1 hours to complete. It seems that MySQL index creation becomes very slow when the table size becomes very big. And partitioning reduces the table into smaller trunks.

  Read the article

• Missing Memory on Windows Server 2008

  - by Chris Lively

  I have a windows 2008 x64 server with 8GB of RAM installed. Task Manager and Resource Monitor both insist that 7.5GB of the RAM is in use. However, the memory list under Processes (Memory Private Bytes) doesn't add up. I do have Show Processes from all users checked and hand adding the numbers I come up with about 3.5GB of RAM. I also looked at the latest copy of SysInternals Process Explorer. And neither the Private Bytes or Working Set adds up to more than about 3.5GB of RAM in use. What's going on? ===== Update: I bounced the server to see what would happen with the memory utilization. After boot and regular operations began it sat at 3GB of RAM usage. 18 hours later, it's back up to 6.8GB of usage with no indication as to where the additional 3.5GB or so of RAM is being used. Here are links to screen shots of the resource monitor and task manager: Resource Monitor Task Manager Update 2: Well, I believe I located the problem. When I detached one of the larger databases from my sql server the amount of ram shown as "in use" dropped drastically. The Memory Private Bytes count barely moved. So I'm guessing that SQL server has some way of allocating memory where it doesn't really show up in any of the monitors. I went further and created a new database file, then transferred all of the data from the one I detached. Even though it has the same data, and the same transactions going through it, the memory in use has stayed low. Maybe there was some corruption in the DB? I'll leave it to the DB gods and go searching for another "problem" ;)

  Read the article

• Files in Windows 7 case-insensitive?

  - by ChrisW

  I've got 2 files on a Unix server which I tried to ftp (using FileZilla) to a Windows 7 machine - tdda.png and TDDA.png - initially FileZilla complained that TDDA.png was already a file when I tried to transfer TDDA.png, so I renamed it to TDDA2.png before transferring it. I then tried to rename it back to TDDA.png in Windows and get the notification: "Do you want to rename 'TDDA2.png to ''tdda(2).png? There is already a file with the same name in this location" Has Windows 7 got some case-insensitivity built in somewhere? I've never experienced it with any other version of Windows...

  Read the article

• Clean installation of RHEL 5.5 claims package "desktops" is missing

  - by TKguru42

  Hi all, I'm a student worker in the CS department of my university, so please forgive me for any unprofessional descriptions. Simplified explanations are appreciated. I recently replaced some bad graphics cards in a few public workstations. The machines are all the same model. Before putting them back on the network I did fresh installs of RHEL---first I tried 5.4, but yum update ran into all sorts of ugly dependency errors and if I tried to remove any of the problematic packages, the whole operating system FUBAR'd. Using RHEL 5.5 gave me the same errors during install saying that "java.1.5.1-sun*" and "desktops" were missing, but yum update didn't have any dependency problems. Now that I tried logging in through the GUI, I encounter no GUI past the standard RHEL login page. The desktop is a uniform light teal and there's no system tray. An xclock window and an xterm window are open, and Firefox opens automatically, but that's it. Nothing else. What's REALLY confusing is that the computer claims that gnome is already installed, except it clearly isn't working. Any help or advice is greatly appreciated. If it helps, our department uses kickstart to run our standard Linux installs. I can try to get the script if that would be of use. Thank you!

  Read the article

• Reread partition table without rebooting?

  - by Teddy

  Sometimes, when resizing or otherwise mucking about with partitions on a disk, cfdisk will say: Wrote partition table, but re-read table failed. Reboot to update table. (This also happens with other partitioning tools, so I'm thinking this is a Linux issue rather than a cfdisk issue.) Why is this, and why does it only happens sometimes, and what can I do to avoid it? Note: Please assume that none of the partitions I am actually editing are opened, mounted or otherwise in use. Update: cfdisk uses ioctl(fd, BLKRRPART, NULL) to tell Linux to reread the partition table. Two of the other tools recommended so far (hdparm -z DEVICE, sfdisk -R DEVICE) does exactly the same thing. The partprobe DEVICE command, on the other hand, seems to use a new ioctl called BLKPG, which might be better; I don't know. (It also falls back on BLKRRPART if BLKPG fails.) BLKPG seems to be a "this partition has changed; here is the new size" operation, and it looked like partprobe called it individually on all the partitions on the device passed, so it should work if the individual partitions are unused. However, I have not had the opportunity to try it.

  Read the article

• solution for an offline server

  - by dashmug

  I'm trying to setup a development server at work that will ideally be able to test drive a couple of projects in PHP, Rails, or Django (not always running at the same time). I develop the apps locally on a Mac and then I'll put the projects up on this server for testing with my actual users (non-techies) before deploying to a production server. My problem is that we have a very poor internet connection (almost negligible) at work and doing the usual apt-get/yum/ports (make, clean, install) processes for setting up servers always get their packages from online repositories somewhere. I know I could probably download the source and then compile them myself but that's going to be too much of a hassle for me. I'm thinking about two solutions: Plan A: Run a server VM on my Mac and then use this VM as the source repository for the offline server. I've read about Ubuntu's apt-proxy and it seems to be good enough though I haven't tried it yet. I'm not sure if this is possible but can I simply do apt-get install nginx --downloadonly so that the package and its dependencies will be downloaded into my VM and my server can use the VM as the source repo for apt-get? Plan B: Run a server VM on my Mac (which I can setup/update easily when I'm home) and then clone the VM to the offline development server. Maybe I should simply make the server a VM host so I can simply copy the VM over. I think this is okay for the first-time setup but subsequent updates will take too long (cloning the VM image). If I was working on Windows, I imagine it'd be easier because most services have an installer file that I can download and then run at the server. If you could suggest another way, it would be much appreciated. Update: From Michael Hampton's answer, I found a possible solution which is apt-cacher. I also found this page on Ubuntu's website. I wonder if there is a better tool than this one.

  Read the article

• Windows Displays Double the Actual Installed Physical Memory

  - by Andrew Barber

  I have a server I've installed Windows Web 2008 R2 on, which is reporting that I have double the physical memory installed as is actually the case. In msinfo32 "Installed Physical Memory" shows as 2x what ever the actual installed amount is, though "Total Physical Memory" shows the correct amount. The "System" info window shows installed memory as 2x, with the correct amount in parenthesis listed as the "usable" amount). This server mistakenly had Windows Web 2008 (32-bit) installed on it just previously, and that OS also reported the same faulty information as Win2K8R2 is reporting. BIOS reports the correct amount, memtest was run on this server before installation, and a previous Windows 2000 instance installed on this system also reported the correct amount, as I recall. Server operation seems to be fine as well (it's only trying to use the correct amount of memory). The server is a generic pizzabox running on a SuperMicro X6DVL-EG with dual Xeon-3.2's. Memory installed are 4 matching mt18vddf12872g-335c3 sticks (1GB pc2700 DDR ECC REG cl2.5) This behavior occurs whether two or all four are installed. So, has anyone seen something like this before? Have any idea about what's causing it, and how I should be concerned about it? Everything else seems good so far, and I'll be upgrading the memory before putting the server into service, but I don't want to spend too much time/money/effort on the server if it's got something odd going wrong here. UPDATE: There was a question I ran into regarding memory sparing in the BIOS and a possible (buggy) effect thereof; however, flipping that bit back and forth in the BIOS revealed that isn't the issue. Still flummoxed a bit about this one, though I still have seen no negative impacts. Post-Answer Update (January 13, 2011): Upgrading the system with new, larger memory has fixed this issue.

  Read the article

• How to get IE to open JavaScript as text

  - by Pete

  I am running IE 9. Up until last week sometime, if I would put the URL of a JavaScript file in the address bar, it would show the JavaScript as text in the browser window. Now when I do that, it wants to download the JavaScript file. How can I revert it to the previous handling? This is annoying since I'm developing a web application and if I can get it to display the .js files as text in the browser, then I can refresh it to force the cache to update. Update: I've tested on several co-workers machines. For some, browsing to .js files renders them in the browser (IE 9 in all cases). In others, it asks for a download. File associations don't seem to have any effect. One co-worker we tested with IE and Chrome. IE wanted to download it, but Chrome rendered it as text. This makes me think it's an IE issue and not an OS issue.

  Read the article

• MySQL keeps crashing due to bug

  - by mike

  So about a week ago, I finally figured out what was causing my server to continually crash. After reviewing my mysqld.log I keep seeing this same error, 101210 5:04:32 [Warning] option 'max_join_size': unsigned value 18446744073709551615 adjusted to 4294967295 Here is a link to the bug report, http://bugs.mysql.com/bug.php?id=35346 someone recommend that you set the max_join_size vaule in my.cnf to 4M, and I did. I assumed this fixed the issue, and it was working for about a week with no issues until today... I checked MySQL and the same error is now back, 101216 06:35:25 mysqld restarted 101216 6:38:15 [Warning] option 'max_join_size': unsigned value 18446744073709551615 adjusted to 4294967295 101216 6:38:15 [Warning] option 'max_join_size': unsigned value 18446744073709551615 adjusted to 4294967295 101216 06:40:42 mysqld ended Anyone know how I can really fix this issue? I can't keep having mysql crash like this. EDIT: I forgot to mention every time this happens I get an email from linode staying I have a high disk io rate Your Linode, has exceeded the notification threshold (1000) for disk io rate by averaging 2483.68 for the last 2 hours.

  Read the article

• Timestamp Updating Constantly on /dev/null

  - by motorleague

  I've been working on a problem with a /dev/null file on an AIX system (just for background it looks as though it was inadvertently deleted and recreated as a normal file by somebody), but in trying to determine what caused the problem, I noticed that the timestamp on it seems to update every minute. I've observed this on several AIX servers at my workplace. At present I can't entirely rule out this be something specific to the Application being used at my workplace, so I compared with CentOS and Debian based computers at home last night. The CentOS box, which runs 24 hours, had a mod time on /dev/null of around 4 days ago (during which time it was essentially just being used as a web browser and multimedia player, although it would have had active but essentially unused Apache, MySQL and VMM processes running in the background). The timestamp on /dev/null on the Debian machine, which was a just booted laptop, pretty much reflected the boot time, but I tested redirecting STDIN from, and STDOUT to it, and the modification time was unchanged (I'm not sure 100% sure if directing data to /dev/null constitutes "writing to it" in the way it would a normal file). So my question is essentially, could anybody please offer any advice with regards to what circumstances (permissions changes etc.. aside) might cause the timestamp on /dev/null to update? Thanks very much for any suggestions. Alex.

  Read the article

• Get off greylisting (the reason why our emails bounced back)

  - by user34402

  Hello, I'm system administrator in online store. We send several emails to our clients after purchase: confirmation, invoice and sale notification to our staff. Recently we got most of emails bounced back and some bounces describes a reason as greylisting, others - just general failure. It is ruining our business because clients are calling that they didn't get the emails with confirmation and invoices. How to get off greylisting, and to not be greylisted? What actions should we do? Mailserver is dedicated machine using Mailenable on Win 2003. Thanks.

  Read the article

• Git completion __git_ps1 really slow on Mac

  - by mckeed

  I've had __git_ps1 in my bash prompt for a while, but just recently (I noticed it after I did some messing around with Homebrew and rbenv), it has slowed down my prompt horribly. When I'm in a git directory I have to wait 3-4 seconds after every command for the prompt to appear. If I just mash return and watch the Activity Monitor, it shows that distnoted and Finder are using more CPU than normal during the delay. Could something git-completion.bash is doing be triggering a notification to Finder? Maybe it involves folder actions or something?

  Read the article

• Outlook 2010 search not working after upgrade to windows 8

  - by Klaaz

  After upgrading my computer to Windows 8 Outlook 2010 has stopped displaying search results. Normally you can enter a (part) of a word in the search box on top of the inbox list and it will show you result immediatly. Even mails allready visible on the screen are not found. Somebody familiar with this issue? Update: maybe relevant: I use an Google Apps Pro account. All mail is synced and locally available in Outlook 2010. I did not change this in any way while upgrading, it was working perfectly before. I can scroll through all the e-mails, new mails are coming in as expected. This morning I received two mails from a person by the name of Rosanne. When searching on her name in Outlook it gives me One (1) result, the last mail from today. Update 2: Rebuilding the index seemed to be working. But after another day it stopped working again. No results whatsoever in Outlook search. Rebuilding indexes every day is not an option as it takes several hours. I suspect it has something to do with the fact that I use Google Apps Pro. It acts like a Exchange server to outlook. In indexing options (configuration) I added the directories containg the PST from this service (mail is also synced locally)

  Read the article

• CF64 on Server 2008x64 breaks pretty much everything else, how to fix?

  I just installed CF64 on a WinServer2008x64 machine. Previously a whole array of classic ASP and ASP.Net apps were functioning, after the CF install they're not. I'm getting an http 500 on everything not coldfusion. I believe it's a mapping issue. CF seems to have dropped a wildcard handler mapping into the IIS config Module IsapiModule Notification ExecuteRequestHandler Handler AboMapperCustom-89420 Error Code 0x800700c1 The upside (if you can call it that) is that the CF install took and seems to be functioning. It appears to have dropped in

  Read the article

• Windows Internet Connection Issue (HELP)

  - by semajjames1399

  I have a windows 8 hp dual booting ubuntu. When i log onto windows i cant get on the internet... But skype and other applications can just now webpages in a browser what so ever (this is on windows 8). But on ubuntu i have no internet issues at all. From what i see right now its only the browsers in windows 8 that cant get the internet, and ive tried all the browsers i had (chrome, ie, firefox) and they cant connect but in the win8 notification area it says im connected. I can even ping via cmd. HELP! Thanks. Whats not working is that i cant get access the internet through the windows 8 broswer.

  Read the article

• Why does the Windows XP Task Manager icon disappear from the tray?

  - by Jason Owen

  One of the more annoying bugs in Windows XP is the tendency for the Task Manager icon to not show up in the tray (aka the notification area). Sometimes it does, sometimes it doesn't, and it's not consistent enough to have an obvious cause. Looking on Google turns up a bunch of forums that have the same problem but no working solution. Why does the task manager icon sometimes not show up? How can I repair it when this happens (how can make it show up when it's missing)? How can I prevent it from not working in the first place, so that I don't have to worry about repairing it after the fact?

  Read the article

• Allow connections to only a specific URL via HTTPS with iptables, -m recent (potentially) and -m string (definitely)

  - by The Consumer

  Hello, Let's say that, for example, I want to allow connections only to subdomain.mydomain.com; I have it partially working, but it sometimes gets in a freaky loop with the client key exchange once the Client Hello is allowed. Ah, to make it even more annoying, it's a self-signed certificate, and the page requires authentication, and HTTPS is listening on a non-standard port... So the TCP/SSL Handshake experience will differ greatly for many users. Is -m recent the right route? Is there a more graceful method to allow the complete TCP stream once the string is seen? Here's what I have so far: #iptables -N SSL #iptables -A INPUT -i eth0 -p tcp -j SSL #iptables -A SSL -m recent --set -p tcp --syn --dport 400 #iptables -A SSL -m recent --update -p tcp --tcp-flags PSH,SYN,ACK SYN,ACK --sport 400 #iptables -A SSL -m recent --update -p tcp --tcp-flags PSH,SYN,ACK ACK --dport 400 #iptables -A SSL -m recent --remove -p tcp --tcp-flags PSH,ACK PSH,ACK --dport 400 -m string --algo kmp --string "subdomain.mydomain.com" -j ACCEPT Yes, I have tried to get around this with nginx tweaks, but I can't get nginx to return a 444 or abrupt disconnect before the client hello, if you can think of a way to achieve this instead, I'm all ears, err, eyes. (As suggested by a user, bringing this inquiry over from http://stackoverflow.com/questions/4628157/allow-connections-to-only-a-specific-url-via-https-with-iptables-m-recent-pote)

  Read the article

• Failed Software RAID0 on Linux - Attempting to recover data

  - by Gizmo_the_Great

  I have a two disk RAID0 software raid (not hardware raid) that is reported to have failed during boot and my OS won't start. Using a Live CD, I get the following output : sudo mdadm -E /dev/sdc1 /dev/sdd1 /dev/sdc1: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 3710713d:fb301031:84b61247:d1d53e0f Name : HP-xw9300:0 Creation Time : Sun Sep 1 15:22:26 2013 Raid Level : -unknown- Raid Devices : 0 Avail Dev Size : 1465145328 (698.64 GiB 750.15 GB) Data Offset : 16 sectors Super Offset : 8 sectors State : active Device UUID : ad427cd2:9f885f57:7f41015f:90f8f6af Update Time : Sun Jun 8 12:35:11 2014 Checksum : a37407ff - correct Events : 1 Device Role : spare Array State : ('A' == active, '.' == missing) /dev/sdd1: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 3710713d:fb301031:84b61247:d1d53e0f Name : HP-xw9300:0 Creation Time : Sun Sep 1 15:22:26 2013 Raid Level : -unknown- Raid Devices : 0 Avail Dev Size : 976771056 (465.76 GiB 500.11 GB) Data Offset : 16 sectors Super Offset : 8 sectors State : active Device UUID : 2ea0199d:cb08d9e7:0830448a:a1e1e348 Update Time : Sun Jun 8 13:06:19 2014 Checksum : 8883c492 - correct Events : 1 Device Role : spare Array State : ('A' == active, '.' == missing) GParted lists both disks, detects the flags as 'Raid' and lists the data usage. Can anyone please help me re-assemble just so that I can copy some of the data off that I have not backed up recently? Thanks

  Read the article

• How do I prevent lighttpd from caching static files, even when modified on disk?

  - by Pixelastic

  I am using lighttpd to serve static files. I have a bunch of images in a dir that I regularly update. This will change the file content (and filesize) as well as the modification date, but not their filename. When I access the files through http, the updates are not taken into account and lighty serves the old file. I can manually rename the file to something different, then lighttpd will return a 404 error, and if I rename my file back, I will get the correct updated version. Seems like lightty is using some kind of cache mechanism of its own (which is fine) to return static files. Unfortunatly, it seems that this mechanism doesn't update itself when files are modified. I checked through Wireshark, and my browser is really doing a request to the file, this is not a browser caching issue. It returns a 200 OK when requesting it from an empty cache, and a 304 Not Modified otherwise, as expected. But the file is returned with a wrong Last-Modified header that do not reflect the real last modification date. Maybe there is some config directive that I am not aware of ? I would like the files returned by lighty to reflect the changes made on disk directly, or at least being able to invalidate its cache.

  Read the article

• Can I prevent a particular program from showing up in the taskbar on Windows XP?

  - by jsnlxndrlv

  I have a program that I need to run more or less continuously, but which I won't need to access very frequently. Currently, launching the program creates a window and causes the program to appear on the taskbar. I'm fine with the program window appearing, but I'd just as soon the taskbar be reserved for programs that I need to switch between frequently—it would be superior for this program to only appear as an icon in the notification area, if at all. Is this possible? How do I do this?

  Read the article

< Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >