Search Results

Search found 2488 results on 100 pages for 'virtualization portfolio'.

Page 37/100 | < Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• CLI-Based monitoring tool for KVM

  - by Pinnacle

  I am developing a scheduler for running VMs on KVM. The scheduling has over-commitment of resources like memory and CPU. For this, I need a CLI-based monitoring tool that keeps me giving information about the resource usage of each VM, because it might be the case that due to over-provisioning of resources, VMs on a particular host are running very slowly depending on the benchmarks/programs each VM is running, and then I need to migrate a VM to another host and so on. I looked into libvirt-based tools like collects, MUNIN, Nagios-vert, etc.( http://libvirt.org/apps.html#monitoring ) I also looked into Ubuntu utility perf-kvm ( http://manpages.ubuntu.com/manpages/maverick/man1/perf-kvm.1.html ) I want to ask which CLI-based would be recommended by the community so that I can make a automated scheduler that takes care of the above situation.

  Read the article

• KVM Guest Reboot Loop

  - by javano

  I have been pulled into a situation where a KVM server (CentOS 6.2) lost power and upon reboot one of the guests hasn't started up again (XP SP3). I have SSH'ed in and someone must have changed something relating to the hyper visors prior to the power loss, but not rebooted all the guests. This particular guest wouldn't start because it was configured to use /usr/bin/qemu-system-x86_64 which isn't there now (assuming it was before?). I changed it to use /usr/libexec/qemu-kvm as this is what all the other guests on this server seem to be using, and its booting up. Using virt-manager on my local machine I can connect to the display of the XP machine and it gets as far as this screen; http://support.gateway.com/emachines/issues/2-1131285152-01.gif The problem I face now, is that which ever option I choose the machine just reboots. So it's and endless loop. I thought that perhaps a file system error maybe present due to the unclean shutdown. There is an XP SP3 ISO mounted under the guest, which I booted from in an attempt to access the recovery tools, but I don't have the Administrator password! I am out of ideas, and it's turning out to be quite the conundrum. Should I use a 3rd party live CD to test the FS for errors? How else can I trouble shoot these restarts?

  Read the article

• Optimal Configuration for five 300 GB 15K SAS Drives

  - by Bob

  I recently acquired an HP Z800 workstation that has five 300 GB 15K SAS Drives. This system will be dedicated to running multiple virtual machines under VMware Workstation (Note: I'm not using ESXi because I do plan to use the system for other purposes.). For the host OS, I plan to install RHEL 5. My number one concern is guest performance. For example, should I create a RAID 10 array for the OS and virtual machine storage with four of the drives and reserve the 5th? Or, is there a solution that will provide better performance?

  Read the article

• Using VirtualBox/VMWare to deploy software to multi sites ?

  - by Sim

  Hi all, I'm currently evaluating the feasibility of using VirtualBox (or VMWare) to deploy the follow project to 10 sites Windows XP MSSQL 2005 Express Edition with Advanced Services JBoss to run 1 in-house software that mostly query master data (customers/products) and feed to other software Why I want to do this ? Because the IT staffs in my 10 sites are not capable enough and the steps taken to setup those "in-house project" are also complicated What are the cons I can forsee ? Need extra power to run that virtualbox instance The IT staffs won't be much knowledgeable 'bout how to install the stuffs Cost (license for VirtualBox in commercial environment as well as extra OS license) I really seek your inputs on the pro/con of this approach, or any links that I can read further Thanks a lot

  Read the article

• VirtualBox: using physical partition as virtual drive

  - by Hamman Samuel

  Background: I am using VirtualBox installed on Windows 7. From within VirtualBox I am using Xubuntu as a virtual OS. The reason I chose this approach is so that I don't have to keep turning off Windows and rebooting from Xubuntu every time I needed to switch OSes. And VirtualBox's seamless mode is pretty amazing to allow me see Xubuntu and Windows 7 all in one screen. Issue: Now I am thinking of a way to have Xubuntu more integrated into my system. By this I mean I want to have a physical partition for Xubuntu. But I want to still have the feeling of the seamless mode. Question: So finally, my question is: is it possible to load a partition in VirtualBox as a virtual OS? Case examples: Ideal scenario would be: I physically boot up and login to Windows 7. Now I want to access Xubuntu, so I load VirtualBox and access my Xubuntu partition without rebooting. And the other way around too, i.e. I boot up the system, login to Xubuntu, and can access the actual Windows 7 partition through VirtualBox. Other info: Please note that I am not talking about getting access to files, as I have a completely separate partition for my files, and am very familiar with VirtualBox's Shared Folders option.

  Read the article

• the kvm's terminal works weirdly

  - by Lai Yu-Hsuan

  I connect to a remote machine from the local machine and use virsh console to enter the virtual machine. I don't know how to exactly depict how it works. Normally it works well, but when I run VIM: Then it can't be recovered unless I cut the connection up: It's very hard to work with a broken terminal. Any advice? My terminal works well on my local machine and the remote machine in which the virtual machine runs.

  Read the article

• Identify OpenVZ virtual machine from inside

  - by Alfred Godoy

  Is there any way for me to identify which OpenVZ container I am in, from inside the container? I am working on a setup where OpenVZ machines shall boot the same (read-only) disk image, so I can not configure them individually in the file system. I need a unique identification for each of the virtual servers, to be used by scripts running inside the OpenVZ containers. (I'm running Debian Lenny, BTW.)

  Read the article

• Optimal Configuration for five 300 GB 15K SAS Drives

  - by Bob

  I recently acquired an HP Z800 workstation that has five 300 GB 15K SAS Drives. This system will be dedicated to running multiple virtual machines under VMware Workstation (Note: I'm not using ESXi because I do plan to use the system for other purposes.). For the host OS, I plan to install RHEL 5. My number one concern is guest performance. For example, should I create a RAID 10 array for the OS and virtual machine storage with four of the drives and reserve the 5th? Or, is there a solution that will provide better performance?

  Read the article

• openvz graphing user_beancounters

  - by Jona

  Hi there, We run a cluster of openvz servers and are looking for a way to automatically graph the content of user_beancounters for all ves. We currently have a fairly rudimentary cron which alerts us when limits are hit but we could like a graphing solution to show us history. Obviously we could roll our own using some fancy bash/php/perl and rrdtool but we're wondering if there are any existing solutions before we go down this path. We current run a cacti/snmp based graphing infrastructure.

  Read the article

• Keeping rackspace vserver alive

  - by mit

  It appears to me that rackspace somehow freezes cloud VMs after some idle time. This means the first page request to a php page takes much longer to respond than the subsequent requests. I am actually querying a machine with wget from a different host now to keep it "alive". But I wonder what frequency would be necessary. Does anyone know the time period after which they send a VM to "sleep"? I guess it would be some minutes. EDIT: There is no caching involved on the php site. It just recently moved from another vhost and there was never such latency on the first request.

  Read the article

• KVM Hosting: How to efficiently replicate guests

  - by javano

  I have three KVM servers each with 1 guest VM, running directly on it's local storage, (so they are essentially getting a dedicated box worth of computing power each). In the event of a host failure I would like the guests replicated to at least one of the other hosts so I can spin it up there, until the failing host is fixed. I am curious about KVM cloning. I can clone a VM live or when it's suspended/shutdown. Obivously suspended VMs will naturally be quicker to clone but these three VMs comprise three parts of a single solution, so I don't want to ever have any one of them shutdown. How can I efficiently clone these VMs between servers? I have had a couple of ideas, but are these insane or, is there a better method I have missed for my scenario? Set up a DRDB partition between box 1 and 2 where VM 1 runs from, and so is replicated between box1 and box 2, repeat between box 2 & 3, and box 3 & 1 (This could be insane, I have never used DRDB only read about it) Just use standard KVM CLI clone options to perform live clones (I'm dubious about this because I don't know how long it will take and what the performance impact will be during) Run a copy of each VM on at least one other host, and have the guest on one host export it's data to the matching guest on another host where it can import that data, scripting this on the guest) Some of other way? Ideas welcome! Side Note These servers have 4x15k SAS drives in a RAID 10 so they aren't rocketing fast, and as I mentioned, each VM runs from the host's local storage, no NAS or SAN etc. So that is why I am asking this question about guest replication. Also, this isn't about disaster recovery. Guests will be exporting their data to a NAS over a VPN, so I am looking at how I can have them quickly spun up in a host failure situation.

  Read the article

• Running Android emulator inside a Virtualbox Vm

  - by sgargan

  I'm trying to setup a VM with a complete android development stack (SDK, Platforms, Eclipse etc) for a Hackathon. I'm having real trouble getting the emulator to start in the VM. I realize that the emulator is essentially a VM itself inside the Vbox VM and so is going to be slow, but it just hangs at the Android splash screen and never gets any further. Might there be something going on with the VM that is causing it to run so very slowly? Is there anything I can do to give the VM more CPU? I've tried setting the execution cap to 100% but it didn't help any. Anyone know what might be going on here, or have any ideas about how I might speed it up? Thanks Steve.

  Read the article

• vihostupdate, many patches at once

  - by skomak

  Hi, i have ESXi 4.0 installed so i want to install all patch bundles available using vihostupdate.pl script from vm perl sdk. I can install it by typing: vihostupdate.pl -server 192.168.1.177 -b "C:\Documents and Settings\dawids\Pulpit\patche\ESXi-4.0.0-update01.zip" -i then patch 2,3 etc. But I would like to install them all at once, is there such possibility? Maybe there is possible to use vihostupdate patch1 then vihostupdate patch2... and after all patching reboot instead rebooting after 1 patch bundle. How is it working?

  Read the article

• My HyperV Virtual Server stops with critical error.

  - by Svisstack

  Hello, I on microsoft hyper v create a server, i installing on it linux debian, but while installation this server stopped with critical error and if I start it, he stops after approximaly 1 minute. How to debug it? Where i can find information about this critical error because in a events viewer I can't find any information about it.

  Read the article

• What disk setup is needed / best practice for hypervisor-only servers?

  - by Luke404

  Planning to buy some servers to run an hypervisor (Citrix XenServer or VMware vSphere, still have to decide between the two) we'd like to boot off the local redundant SD card module offered by various vendors (eg. Dell, HP, etc...). The actual VMs will run from an existing iSCSI SAN (which, by the way, can't support booting the servers directly off the SAN). What are the reasons, if any, to choose completely diskless servers VS having some local storage? And what would be the guidelines to choose that local storage? (number of spindles, raid level, etc)

  Read the article

• Custom Windows AMI for Amazon EC2

  - by cutyMiffy

  Hello: I am new to the Amazon EC2 services and I am planning to host a Windows based vm on Amazon. I have lot of fuzziness about AMIs on Amazon. So my first question would be, am I be able to install softwares and frameworks(e.g. Silverlight, .NET, etc) on a existing Windows instance that I select? And if not, how can I create a custom AMI so that I can install these softwares that I need before I submit it to Amamzon and launch? Thanks a lot for your help :) Deeply appriciated

  Read the article

• How to boot a partition using a virtual pc.

  - by Fantomas

  I have backed up my failing hard drive using a ddrescue Linux command to two partition files - p1 and p2 5GB and 90GB each. Now, without saving this back to an actual disk - is there a way for me to boot my old computer virtually, using Virtual PC or Parallels or VMWare? How? Thank you.

  Read the article

• Is it possible to create a delta VM?

  - by iTayb

  I have a VM of approx. 18GB. Sometimes I need temporally clones of it, so I clone it. The problems are: * It takes a while until it's done. * Sometimes I happen to need dozen of clones and I'm running out of storage. I wonder if there's a way to create a VM that saves only the delta (difference) since the delployment out of the source machine. That way each new VM's filesize should be 100MB at most, and creating it will be much faster. I've heard that VMWare View is using this concept. Is such a thing possible for ESXi as well? I'm using ESXi 4.1 with VSphere 4.1. Thanks!

  Read the article

• ipv6 with KVM on debian

  - by Eliasdx

  I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

  Read the article

• Can windows domain controller be virtualized?

  - by FerranB

  Just the question on the title. There is any problem? Any experience on this?

  Read the article

• Create Virtual Image of Laptop before Formatting

  - by Simon Mark Smith

  I have a 3 year old laptop running Windows XP that I used for business. Although I have not used the laptop in over a year, I now want to re-commission it with Windows 7 and a fresh install. Before I do the fresh install I want to create a Virtual Image of the laptop that I can keep and potentially run on my desktop machine should I ever need to access any of the old files/projects that it contains currently. I know that most people will say just copy the files over to your desktop, but my concern is the configuration of the laptop. I used to use it for development and it has older versions of Visual Studio, SQL Server, Active X controls etc, etc than I currently use so I really want to preserve the environment not just the files. So really I am asking what is the best tool-set/method to achieve this? I understand there are free VM tools available but I have never done this before and would appreciate any help.

  Read the article

• Virtual PC with Multi Monitors

  - by user41013

  Hi I have recently intalled Virtual PC and was wondering if it possible to make use of both of my monitors with it. I have managed to get a pseudo multi screen effect by connecting using Remote Desktop connection, but this isn't really what i wanted. Is this possible? Thanks

  Read the article

• Virtual PC with Multi Monitors

  - by user34710

  Hi I have recently intalled Virtual PC and was wondering if it possible to make use of both of my monitors with it. I have managed to get a pseudo multi screen effect by connecting using Remote Desktop connection, but this isn't really what i wanted. Is this possible? Thanks

  Read the article

• 2xAMD Opteron 6128 with libvirt, Physical CPU 13 doesn't exist

  - by yak

  I need help with libvirt(?) problem. Server specs: ProLiant DL165 G7 2x AMD Opteron(tm) Processor 6128 System: Debian GNU/Linux testing (wheezy) 3.2.0-3-amd64 libvirt 0.9.12-5 kvm 1:1.1.2+dfsg-2 $ grep processor /proc/cpuinfo | wc -l 16 $ virsh nodeinfo setlocale: No such file or directory CPU model: x86_64 CPU(s): 16 CPU frequency: 800 MHz CPU socket(s): 2 Core(s) per socket: 4 Thread(s) per core: 1 NUMA cell(s): 1 Memory size: 66114200 KiB $ virsh capabilities .. <topology> <cells num='4'> <cell id='0'> <cpus num='4'> <cpu id='0'/> <cpu id='1'/> <cpu id='2'/> <cpu id='3'/> </cpus> </cell> <cell id='1'> <cpus num='4'> <cpu id='4'/> <cpu id='5'/> <cpu id='6'/> <cpu id='7'/> </cpus> </cell> <cell id='2'> <cpus num='4'> <cpu id='12'/> <cpu id='13'/> <cpu id='14'/> <cpu id='15'/> </cpus> </cell> <cell id='3'> <cpus num='4'> <cpu id='8'/> <cpu id='9'/> <cpu id='10'/> <cpu id='11'/> </cpus> </cell> </cells> </topology> .. $ virsh vcpupin vm 0 13,12,11,10,9,8,7,6,5 error: Physical CPU 13 doesn't exist. error: cpulist: Invalid format. Question? Why my VM Guests use only first 8 CPUs and next 8 are idling? $ for host in virsh list | awk '{print $2}'; do virsh vcpuinfo $host; done | grep ^CPU: | sort | uniq CPU: 0 CPU: 1 CPU: 2 CPU: 3 CPU: 4 CPU: 5 CPU: 6 CPU: 7 Any ideas how to change it?

  Read the article

< Previous Page | 33 34 35 36 37 38 39 40 41 42 43 44  | Next Page >