Search Results

Search found 32598 results on 1304 pages for 'ubuntu touch'.

Page 371/1304 | < Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >

• HP Proliant DL360 G5 + MSA50 RAID Setup recommendations

  - by JohnRB

  I am running a HP Proliant DL360 2 x 3GHz Xeon 16GB Ram P400 integrated RAID card with 6 x 73GB SAS HDDs running Ubuntu Server 14.04 CLI only. I recently got my hands on a MSA50 SAS Enclosure (10 x SAS HDD bays w/ SAS in/out interface) and wondering what you guys recommended as far as an addon raid controller for one of the pciex slots. I have both slots free Full and Half sizes. Any suggestions are greatly appreciated, I am an I.T. Consultant but have not used these particular units before so I was hoping to hear from someone who has. Thanks!

  Read the article

• Issues with DHCP over multiple subnets

  - by Dan Monego

  I have a cisco router configured to handle multiple subnets (10.1.10.n, 10.2.10.n, etc), and an ubuntu system serving DHCP to the computers served by the router. After a restart of the DHCP, the systems on the 10.1 subnet are fine, but neither the server or the computers configured on the other subnets can see the router at 10.2.10.1 (or 10.3.10.1, or 10.4.10.1). The router can see itself at 10.2.10.1, however. The change that caused this was restarting the server, so I'm approaching it assuming the configuration error is on that end. Is that the likely issue or is there a different problem that would prevent the machines on the 10.2.10 subnet from resolving DHCP?

  Read the article

• Is it possible to control my CPU frequency?

  - by Tim

  My laptop's CPU Type is: Mobile AMD Turion 64 ML-30, 1600 MHz (8 x 200) I was wondering how to find out if its CPU frequency is controllable? What softwares or other ways can control my CPU frequency? My OSes are Windows XP and Ubuntu. Can I control CPU frequency so that the CPU temperature can be controlled not to exceed some temperature? Thanks and regards! More information: My laptop is Acer Aspire 5000. Its motherboard is reported by Speccy as: Manufacturer: Acer, Inc. Model: Lugano M Version: Not Applicable Chipset Vendor: SiS Chipset Model: 760GX Chipset Revision: 03 Southbridge Vendor: SiS Southbridge Model: LPC Bridge Southbridge Revision: 25 BIOS Brand: Acer Version: 3A19 Date: 05/17/05

  Read the article

• Where can I find logs for SFTP?

  - by Jake

  I'm trying to set up sftp-server but the client is getting an error, Connection closed by server with exitcode 1 /var/log/auth.log (below) doesn't help much, how can I find out what the error is? I'm running Ubuntu 10.04.1 LTS sshd[27236]: Accepted password for theuser from (my ip) port 13547 ssh2 sshd[27236]: pam_unix(sshd:session): session opened for user theuser by (uid=0) sshd[27300]: subsystem request for sftp sshd[27236]: pam_unix(sshd:session): session closed for user theuser Update: I've been prodding this for a while now, I've got the sftp command on another server giving me a more useful error. Request for subsystem 'sftp' failed on channel 0 Couldn't read packet: Connection reset by peer Everything I've found on the net suggests this id a problem with sftp-server but when I remove the chroot from sshd config I can access the system. I assume this means sftp-server is accessible and set up correctly.

  Read the article

• localhost name error with linux machines

  - by coderex

  Hi, CASE 1: I have a Ubuntu machine with name midhun.local I can access this in http://midhun.local/svn ... But its can't access from other machines(both Windows and Linux) through this host name. But it works with http://192.168.1.192/svn CASE 2: I have a another machine(windows) having the host-name myname:555 In this case i can access https://myname:555/svn from other windows machines with the same URL. But if am trying to access from the a Linux machine it will not work with the same URL instead of that https://192.1.168.111:555/svn will work. How can I solve the problem. I need to access via the same name from cross domain. How is it possible in LAN Thanks in advance!!

  Read the article

• sSMTP Configuration Question

  - by SevenCentral

  I've installed sSMTP on Ubuntu 10.04 via: sudo apt-get install ssmtp My configuration file is: # # Config file for sSMTP sendmail # # The person who gets all mail for userids < 1000 # Make this empty to disable rewriting. [email protected] # The place where the mail goes. The actual machine name is required no # MX records are consulted. Commonly mailhosts are named mail.domain.com mailhub=smtp.gmail.com:587 # Where will the mail seem to come from? #rewriteDomain= # The full hostname hostname=somedomain.com # Are users allowed to set their own From: address? # YES - Allow the user to specify their own From: address # NO - Use the system generated From: address #FromLineOverride=YES [email protected] authpass=**** usestarttls=yes Am I transmitting my credentials in clear text? Is calling ssmtp a secure operation? Thanks.

  Read the article

• Setting up Shibboleth to secure part of a website

  - by HorusKol

  I've installed the Shibboleth module for apache on Ubuntu 10.04 using aptitude to install libapache2-mod-shib2 as per https://groups.google.com/group/shibboleth-users/browse_thread/thread/9fca3b2af04d5ca8?pli=1 and enabled the module (I have checked in /etc/apache2/mods-enabled) I then proceeded to secure a directory on the server by placing a .htaccess file with the following directives: AuthType shibboleth ShibRequestSetting requireSession 1 Require valid-user Now - I haven't set up an SSL host yet - and I also haven't set up the IdP - but I would expect that the server would block access to this directory - but I'm getting the content without any problems. I have restarted the apache service and I have no errors in the log files.

  Read the article

• Why do I get duplicated entries in my $PATH?

  - by reprogrammer

  I'm using Ubuntu 9.10 (karmic). And, my ~/.pam_environment looks like the following. PATH DEFAULT=${PATH}:~/Adobe/Reader9/bin:~/texlive/2009/bin/x86_64-linux GIT_EDITOR DEFAULT=vim MANPATH DEFAULT=${MANPATH}:~/texlive/2009/texmf/doc/man INFOPATH DEFAULT=${INFOPATH}:~/texlive/2009/texmf/doc/info But, echo $PATH returns me duplicated entries as the following. /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:~/apps/Adobe/Reader9/bin:~/apps/texlive/2009/bin/x86_64-linux:~/apps/Adobe/Reader9/bin:~/apps/texlive/2009/bin/x86_64-linux I've tried replacing DEFAULT by OVERRIDE in my ~/.pam_environment file. But, that didn't help. Does any one know what's wrong with my ~/.pam_environment?

  Read the article

• How can I remove the ssh last login info?

  - by Gnijuohz

  Whenever I log into a server using ssh. The prompt gives me "last login" information. I was wondering where this information comes from. How can I remove this record so when someone else log into the same server, the person would see my login info with my ip in it? So how can I do this? For the record, I am not hacking someone's computer and the server runs Ubuntu 12.04. EDIT: which file logs this kind of information? If I find the file, then I can do anything to it as root. Thanks.

  Read the article

• NFSv4 - ACLs not working

  - by alex

  I've setup an NFSv4 server (Debian) and client (Ubuntu/Mythbuntu). It seems that uid username mapping is working nicely out-of-the-box (I get correct usernames on ls -l if the usernames match between the two boxes, even if the uids don't), but ACLs are not working. I've installed nfs4-acl-tools and I can read the ACLs correctly on the client, but they don't get applied. What needs to be done for ACLs to work? To clarify; username mapping works for regular permissions. ACLs are applied using uid/gid (I can even set ACLs by uid and they work).

  Read the article

• Removing DS_Store files and variants?

  - by Ron Gejman

  I am running an Ubuntu 10.04.1 LTS server. Frequently I open up files using AFP from my Mac. Inevitably this created .DS_Store files on the server (although for some reason they are named :2eDS_Store. However, it also creates variants on DS_Store files. These variants are often named similarly to other files in that directory. E.g.: ~$ ls total 60K -rw-r--r-- 1 tarakhovsky 16K 2010-11-30 18:28 :2eDS_Store drwx--S--- 4 tarakhovsky 4.0K 2010-11-08 13:58 :2eTemporaryItems/ lrwxrwxrwx 1 tarakhovsky 15 2010-10-19 17:44 bigdisk -> /media/bigdisk// ... drwxr-xr-x 3 tarakhovsky 4.0K 2010-11-03 18:24 Temporary Items/ drwxr-xr-x 3 tarakhovsky 4.0K 2010-11-30 01:34 tmp/ ... I've disabled creation of DS_Store files using: defaults write com.apple.desktopservices DSDontWriteNetworkStores true so hopefully this won't continue to occur—but I really want to get rid of all of the existing variants of DS_Store files already on the server. Any ideas as to why these variants are being created and how I can get rid of them all?

  Read the article

• How to add exception for backup MX to tumgreyspf?

  - by Waleed Hamra

  I have an Ubuntu raring server running postfix/dovecot as an email server, with tumgreyspf doing greylisting and SPF checks. My problem is that I also have a backup MX server, that is supposed to store my emails temporarily, should my main server ever fails. It usually rejects receiving emails if it finds the main server online and functional. The problem is when it does need to do its job, tumgreyspf rejects all emails from the backup MX with an error like this: Jun 27 16:18:13 hamra postfix/smtpd[28732]: NOQUEUE: reject: RCPT from mxbackup.mydomain.com[x.x.x.x]: 550 5.7.1 <[email protected]>: Recipient address rejected: QUEUE_ID="" SPF Reports: 'SPF fail - not authorized'; from=<[email protected]> to=<[email protected]> proto=SMTP helo=<mxbackup.mydomain.com> any ideas?

  Read the article

• Increasing a Linux partition once VM size increased in vSphere?

  - by dannymcc

  I have a Ubuntu 12.04 VM running on VMWares ESXi 5.1. The server (VM) itself has run out of space, the results of df -h are as follows: Filesystem Size Used Avail Use% Mounted on /dev/sda1 19G 17G 1.2G 94% / udev 490M 4.0K 490M 1% /dev tmpfs 200M 232K 199M 1% /run none 5.0M 0 5.0M 0% /run/lock none 498M 0 498M 0% /run/shm The original VM HDD size was just under 19GB which is I have now increased to 100GB within the vCenter GUI: Is there a simple way of doing this? The VM doesn't seem to acknowledge the increase at all.

  Read the article

• Emacs doesn't load gui.

  - by D Connors

  Hi, whenever I run emacs or emacs23 on terminal I just get the following output: ** (emacs:2620): CRITICAL **: menu_proxy_module_load: assertion `dbusproxy != NULL' failed And the gui doesn't load, and emacs' window never opens. The emacs process doesn't actually crash (the terminal stays busy, and I can see the emacs23 process running with ps -e). I've tried running it with the -D --debug-init arguments, but the same thing happens and the output is exactly the same. However, if I run emacs -nw it successfully runs emacs in terminal mode as if nothing were wrong. Strangely, this problem only started happening the second time I ran emacs today. The first time it worked perfectly fine. Since then, I've tried rebooting and I've tried purging the emacs installation, to no success. I haven't installed any new packages today, but I might have upgraded some, could that be the reason? Is there a way to find out which packages were installed/upgraded today? Thanks I'm running Ubuntu Lucid

  Read the article

• Easily tell if focused on VirtualBox window?

  - by Benjamin Oakes

  Is there a way to make it very obvious that my VirtualBox window isn't in focus? The problem I'm having is switching between workspaces on Ubuntu or OS X and then trying to type in my Windows virtual machine, only to find that it's not in focus. The Windows window looks like it's in focus (based on the title bar), but I'm actually typing in Firefox on the host machine, for example. It's even worse because the Windows text insertion cursor is blinking to show focus. Ideally, I'd like the VM's display to get unsaturated (e.g. a "partial" grayscale) when not in focus, just to prevent this keyboard-focus problem. Other options would be fine too, as long as I don't have to second guess where my focus is. I'm not using the seamless mode -- the display is all within a window.

  Read the article

• Chef bootstrap giving 401 unauthorized

  - by loddy1234

  I'm trying to bootstrap a new chef node by running: knife bootstrap <server ip> -x lewis -N gitlab --sudo But I get the following output: [Mon, 03 Sep 2012 14:45:17 +0000] INFO: *** Chef 10.12.0 *** [Mon, 03 Sep 2012 14:45:17 +0000] INFO: Client key /etc/chef/client.pem is not present - registering [Mon, 03 Sep 2012 14:45:17 +0000] INFO: HTTP Request Returned 401 Unauthorized: Failed to authenticate. Ensure that your client key is valid. [Mon, 03 Sep 2012 14:45:17 +0000] FATAL: Stacktrace dumped to /var/chef/cache/chef-stacktrace.out [Mon, 03 Sep 2012 14:45:17 +0000] FATAL: Net::HTTPServerException: 401 "Unauthorized" My chef server is running Ubuntu 12.04 x32 and the machine I'm trying to bootstrap is running CentOS 6.3 x64 Any idea what's going wrong?

  Read the article

• Connecting to a VirtualBox machine from the host, using an ip address

  - by Doron

  Hello, In a macbook host, I run VirtualBox having a guest ubuntu server, with a NAT network setting. In the virtual machine application "Parallels", I would get on the host an IP address of the guest, to which I could later set hostnames and access it directly. However, I couldn't find a way to accomplish this using VirtualBox. The only solution VirtualBox has for me, is to set port forwarding, and access "localhost" with these ports. How can I have the desired behavior set up, without having to change to a bridged network settings, and expose my guest computer to the network my host computer is connected to ? Thanks.

  Read the article

• Other users on my Server?

  - by Jennifer Weinberg

  I'm buying a Server from a person (that I don't know really well) and I want to make sure that the previous owner hasn't got any access anymore. It's an Ubuntu Virtual Server and I already received the admin access (via shell). How can I find out if there are still other accounts left, who are still able to access my server (e.g. with a still existing shell account, ftp or another type of user account)? And how can I delete them if these accounts exist? Best regards, Jennifer

  Read the article

• Network access to VM only from host ...

  - by Jamie

  I'm trying to do some testing of Ubuntu 10.04 Beta 2 Server in a VMWare environment. The host is XP, and the VM software is VMPlayer. Problem is, I want to be able to see the VM from the network, not just from the host. I can SSH into the VM from the host, but from any other machine on the network I can't even get the VM to respond to a ping. Going the other way (from the VM out) isn't a problem at all. The VM software did an 'easy installer' so I'm not really sure what was going on with the networking. Suggestions?

  Read the article

• Gnome Terminal intercepts ctrl-F1

  - by frank

  Gnome Terminal does not pass on to applications the keypress ctrl-F1. It's an official bug: https://bugs.launchpad.net/ubuntu/+source/gnome-terminal/+bug/932940 The bug is marked Feb. 2012 but lives on in serendipity since 2009. The bug report is not even complete since shift-ctrl-F1 is also affected. However, I noticed that those two keys are the default keys for switch-to-workspace-1 and move-to-workspace-1. So I disabled them. Zero, zippo, zilch: Gnome Terminal would still swallow the keys. Next, I assigned to those two workspace functions totally different keys. The new keybindings did work, Gnome Terminal would still swallow ctrl-F1 and shift-ctrl-F1. Where are the default workspace keybindings stored? [Not in a xml-file.]

  Read the article

• What settings need to be changed to allow EC2 instances to use Amazon's Route 53 for DNS?

  - by ks78

  I have a number of Amazon EC2 instances, all running Ubuntu, which I'd like to configure to use Amazon's Route 53. I setup a script, following Shlomo Swidler's article, but ran into script-related issues, which were answered here. Now, I have the script working, but my instances are still not able to access Route 53's DNS. By this I mean, they are not able to resolve hostnames to IP addresses. My instances are currently configured with the DNS server IP address Amazon pushes out to them by default, does that need to be changed when using Route 53? I'm also IP-restricting my instances using the Security Groups. Could that be the problem? Is there a certain IP address or port I should open to allow communication with Route 53? It seems that DNS requests should be originating from my instances so the Security Groups shouldn't be an issue, but I've been wrong before. If anyone has any ideas, I'd really appreciate it.

  Read the article

• Very High Network out in ec2 instance

  - by Jatin

  I launched an ubuntu-14.04-64bit instance in Amazon EC2 two days back. And I started Tomcat 7.0.54 in that instance and deployed my application war files. It has no other software installed other than tomcat and the default ones. In the past 2 days, its shows 858 GB of Data Transfer(Network Out) from that instance. I have attached a graph of Amazon CloudWatch Metric "Network Out" My application does not do any data download/upload. Its a Java Spring application and the front end is in HTML&Javascript. My application traffic was very low (less than 20 hits) in those 2 days. Is there a way to find out why these data transfers happened and also to find what data has been transferred. If you can see in graph, network out was 20gb per minute. Some more info: Network in was negligible CPU Utilization was very high Everything else was low

  Read the article

• Monitor a log file on Linux and send each line to another program

  - by mlambie

  I run an apt-cacher-ng server on Ubuntu Linux which writes logs in the following format: 1299745593|O|149406|XXX.XXX.XXX.XXX|uburep/pool/main/t/tiff/libtiff4_3.9.2-2ubuntu0.4_amd64.deb 1299745593|O|10154976|XXX.XXX.XXX.XXX|uburep/pool/main/l/linux-firmware/linux-firmware_1.34.4_all.deb 1299748529|O|39368|XXX.XXX.XXX.XXX|uburep/pool/main/n/nagios-nrpe/nagios-nrpe-server_2.12-4ubuntu1_amd64.deb 1300155440|O|680100|XXX.XXX.XXX.XXX|uburep/pool/main/t/tzdata/tzdata_2011c-0ubuntu0.10.04_all.deb It shows the timestamp, direction (in or out), byte count, IP and filename. Every time a line is written to it, I'd like to also send that line to another program. I will have this program insert the line into a database so that I can crunch some statistics about how much bandwidth we're saving through operating a caching server. I do not want to cat the log file every X minutes (via cron) looking for new entries as it'd be somewhat computationally uneconomical. Instead I'd prefer to have a daemon monitor the log, and when a change is detected, each line is sent to my database-insertion script. Will swatch achieve this, or are there better options?

  Read the article

• No HTTP Response from Tomcat 7 EC2 instance

  - by David Kaczynski

  I am new to EC2 (and Tomcat, for that matter), and I am trying to deploy a vanilla Tomcat 7 server to an Ubuntu 12.04.1 EC2 instance and access the default test site over HTTP. My EC2 instance is running, and the Security Group includes port 80: My /etc/tomcat7/server.xml config has been edited to listen for HTTP requests on port 80: 0 I have restarted my Tomcat 7 server via sudo service tomcat7 restart. However, according to sudo netstat -lnp, Tomcat is not listed as listening over port 80: I am unable to get any response from going to the ...amazonaws.com public DNS in a web browser. What am I missing?

  Read the article

• VirtualBox, physical disks, and snapshots

  - by noamtm

  I have an Ubuntu guest installed on a raw HDD (entire disk, not a partition). It runs just fine under WinXP. In addition, I was able to boot directly into it (using the BIOS boot-device selector). At some point, I have created a snapshot of the VM. I have made some changes since then. Today, after a long time, I tried booting into the "VM" disk. It worked, but all the data there is pre-snapshot (or, rather, frozen at the snapshot). Can I somehow merge the changes since I took the snapshot into the physical state?

  Read the article

< Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >