Search Results

Search found 12790 results on 512 pages for 'port islander 2009'.

Page 373/512 | < Previous Page | 369 370 371 372 373 374 375 376 377 378 379 380  | Next Page >

• connection with the application object server could not be established

  - by user44048

  Hello All, I have installed Axapta server on my Axapta(Machine name) machine. When i am going to start the axapta at that time it give error like " connection with the application object server could not be established ". Basic all the steps that i have tested like Service start restart and connection configuration. port number problem. Still i am not able to resolve a problem. please can any one tell me the solution. It's urgent please help as soon as possible. Thank you.

  Read the article

• Clarification of the difference between PCI memory addressing and I/O addressing?

  - by KevinM

  Could someone please clarify the difference between memory and I/O addresses on the PCI/PCIe bus? I understand that I/O addresses are 32-bit, limited to the range 0 to 4GB, and do not map onto system memory (RAM), and that memory addresses are either 32-bit or 64-bit. I get the impression that memory addressing must map onto available RAM, is this true? That if a PCI device wishes to transfer data to a memory address, that address must exist in actual system RAM (and is allocated during PCI configuration) and not virtual memory. So if a PCI device only needs to transfer a small amount of data at a time, where there is no advantage to putting it into RAM or using DMA, then I/O addressing is fine (e.g. a parallel port implemented on a PCI card). And why do I keep reading that PCI/PCIe I/O addressing is being deprecated in favour of memory addressing? Thanks!

  Read the article

• Need to configure multiple default gateways for four seperate physical network ports for a FreeBSD Webserver

  - by user20010

  I need to configure default gateways for four separate physical network interfaces for a FreeBSD Webserver. Basically, this is a web server that needs to be accessed by multiple WANS. I've been using various online resources, and a combination of setfib, pf, and ipfw. This web server will be deployed in multiple sites where access to next hop router info is not available, so we can't use static routes. We've used setfib to successfully create multiple routing tables and can ping beyond every default gateway we've created. Using setfib # ping ip.addr.what.ever we can ping anything available on a wan and beyond the router. The problem is we can't get Apache web server (port 80) traffic to route out when external users access the server(box). Multiple people have examples of binding setfib to ipfw commands, but none of them seem to work.

  Read the article

• Home router for higher network loads

  - by Zizzencs

  I'm trying to find a replacement for my ASUS WL500GP router. Some constraints: my ISP now provides 120 Mbit bandwidth - the router must be able to handle it I have 3 computers and a laptop at home - the router must have at least 4 LAN ports and the WAN port I need to be able to do the following in parallel: use bittorrent with ~1000 connections transfer files from one home computer to another at high speed access one home computer from my workplace I don't really need wireless I don't really want two boxes to serve all these purposes. So I was searching for a router with 1 Gbit ports, jumbo frame support and good reviews, but haven't really found a promising candidate so far. Any suggestions?

  Read the article

• How to tell if my sound card is listed in Device Manager?

  - by Bruhan

  The sound on my computer suddenly stopped working. When I check Sounds and Audio Devices in the Control Panel, I get "No Audio Device" with everything grayed out. When I check the Device Manager under "Sound, video and game controllers" I see the following list: Audio Codecs Legacy Audio Drivers Legacy Video Capture Devices Media Control Devices MPU-401 Compatible MIDI Device Standard Game Port Video Codecs None of these looks like my sound card. Of course, my sound "card" is not really a sound card, it's integrated with the nVidia-nForce motherboard. I'm running Windows XP. So is one of the above my sound device, or is the OS not detecting it? If the latter, how do I get it to detect it?

  Read the article

• Why do people tell me not to use VLANs for security?

  - by jtnire

  Hi Everyone, As per title, why do people tell me not to use VLANs for security purposes? I have a network, where a have a couple of VLANS. There is a firewall between the 2 VLANs. I am using HP Procurve switches and have made sure that switch-to-switch links accept tagged frames only and that host ports don't accept tagged frames (They are not "VLAN Aware"). I've also made sure that the native VLAN (PVID) of the trunk links are not the same as either of the 2 host VLANs. I've also enabled "Ingress Filtering". Furthermore, I've made sure that host ports are only members of a single VLAN, which is the same as the PVID of the respective port. The only ports which are members of multiple VLANs are the trunk ports. Can someone please explain to me why the above isn't secure? I believe I've addressed the double tagging issue.. Thanks

  Read the article

• outlook iptables configuration

  - by mediaexpert

  I've a Debian mail server, but only the outlook users can't be able to download the emails. I've seen a lot of post about some kind of forwarding port configuration, I've tried some commands, but I don't be able to solve this problem, please help me. below INPUT and FORWARD iptables: Chain INPUT (policy DROP 20 packets, 1016 bytes) pkts bytes target prot opt in out source destination 60833 16M ACCEPT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:143 state NEW,ESTABLISHED 18970 971K ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp spts:1024:65535 dpt:110 state NEW,ESTABLISHED Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT tcp -- * * 192.168.0.0/24 0.0.0.0/0 tcp dpt:110 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 ACCEPT tcp -- * * 192.168.1.0/24 0.0.0.0/0 tcp dpt:110 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:25 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:110

  Read the article

• MacPorts on mountain lion - cannot install apache2 due to gettext package

  - by jancha

  I have been having problem with installing gettext package from macports. When I am launching /opt/local/bin/port -v install apache2 it checks dependencies, and continues with gettext package installation. But the configure process freezes here: checking for egrep... /usr/bin/grep -E and nothing happens.. can wait hours, nothing changes. I tried to configure, make, make install manually for that package and it went all fine. But, when same configure is launched by ports, it hangs there. Question: 1) How can that be fixed? 2) Maybe I can somehow manually tell ports, that I installed that gettext package manually already? Sorry, if wrong "site" for this question. Felt most proper one.

  Read the article

• Activating ssl on tomcat

  - by toom

  I want to encrypt the http traffic on a tomcat instance via ssl. Therefore I followed the most simplistic approach described on various webpages. But anyway it simply does not work. Here is what I did: "keytool -genkey -alias tomcat -keyalg RSA" and I enterd "changeit" as the password (since this is the defaut chosen by tomcat) Altering $CATALINA_HOME/conf/servers.xml by uncommenting the following line Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS"/ Restarting tomcat Entering https://localhost:8443 does not work. However, I can still access the page via normal http like http://localhost:8080 The logfile does not contain any suspicious information. What is going wrong here?

  Read the article

• Postfix cleanup daemon access control

  - by Flimzy

  Is there any way to control which hosts are permitted to connect to the cleanup daemon over TCP? Our 'master.cf' contains: 2526 inet n - - - 0 cleanup This is necessary because we have a cluster of SMTP servers running custom code, and they can all inject mail to the centralized postfix server via the cleanup daemon. However, we want to allow only our authorized servers to connect to the cleanup daemon. The current configuration allows any host to connect to port 2526. Clearly we can use iptables to restrict access, but is there a way to do this within postfix itself?

  Read the article

• View apache server across virtual machine?

  - by Mark

  I installed VirtualBox on my Windows 7 machine. Through VirtualBox, I installed Ubuntu 9.10 with apache2. I can view http://localhost from Ubuntu, but is there anyway I can view it from my windows machine too? i.e. run the apache server on ubuntu, and view it from windows? I figured it would open a port or something that would be visible to my whole computer regardless of its virtualness, but I guess not. How do I get around this?

  Read the article

• How to configure my web server for public and development service

  - by Steve

  I have one and only one web server, which runs Windows Server 2008 and wamp. Now I would like to setup SVN on the server so I can program the trunk version of the website. Every time I branch a version and put it to public. While developing on the trunk version, I also want to be able to test it. The web server has 5 IPs so I can use one IP for public website(the branch) and another IP for trunk development test. I believe one wamp server can only handle one 80 port request thus can only handle one website. How can I configure the server so it can handle one IP request and direct to my branch and handle another IP request and direct to my trunk?

  Read the article

• HP Virtual Connect and VLAN Tagging

  - by JaapL

  We have a c7000 chasis with the ability to have 8 uplinks per ESX host. Only 6 are currenlty active. I have a Virtual Switch with multiple vlan port groups and all the VMs are working fine. Recently we've been asked to setup network load balancing for one of our VMs, so we had our Virtual Connect engineer activate the last two uplinks. We then created a new vSwitch and added the two new uplinks to this vSwitch. We then moved the VM to this new vSwitch, but we get no connectivity. What could be the issue? We also added the appropriate VLAN ID. The VConnect engineer says everything is configured correctly and networking TEAM says the appropriate trunking is setup, so we are at a loss...

  Read the article

• software to monitor internet usage on an XP PC? (browser + non-browser)

  - by user39316

  Hi Is there any (ideally open source) software for Windows that can be used on a PC, to monitor the usage of internet from that PC? It would need to include both browser and non-browser sources (e.g. a service that sync's calendar to gmail). So any software on your PC that uses would need to be configured to point to this local internet monitoring software/proxy. The monitoring software/proxy then would be configured to point to the company proxy server (address, port & credentials). Things that come to mind that might be close but not really focused on solving this might be perhaps: Charles Proxy, Fiddler 2, SQUID? The idea would be it could give you a daily/weekly/monthly report of internet upload/download usage on a per program/process/service basis for the PC it is being run on. thanks

  Read the article

• How to disable screens turn off Windows 8.1

  - by Warpzit

  So recently my computer started turning my screen monitors off after a while without activity, if I move the mouse or hit the keyboard they turn back on. I just want them to stay on. My System is windows 8.1 64 bit, I have 2 screens with mini display port and 1 television with hdmi which often is in regular television mode when this issue happens. Now before you jump to conclusions this is what I've tryed: Disabled screen saver Power saving settings to high with following set: Turn of the display: Never Put the computer to sleep: Never Turn off hard disk after: Settings: Never Sleep: Sleep after: Settings: Never Display: Turn off display after: Settings: Never Display: Enable adaptive brightness: Settings: Off Multimedia settings: When sharing media: Settings: Prevent idling to sleep. Any pointers that get me in the right direction will be greatly appreciated.

  Read the article

• wamp server does not start: Windows 7, 64Bit

  - by Ram

  I am trying to install wamp server (following is the exact setup name) on windows 7, 64Bit OS. But it never starts, icon stays in orange color meaning some services did not start. wampserver2.2e-php5.3.13-httpd2.2.22-mysql5.5.24-x64 I have been searching from last 3hours but did not find any solution. Port 80 is not in use. In windows services, when I try to start wampapache service manually, it throws following error: Windows could not start the wampapache service on Local Computer. Error 1053: The service did not respond ot the start or control request in a timely fashion. apache_error.log is empty. Things use to work fine in windows XP. May be this is a repeated thread, but I did go through similar posts. But nothing worked! Please help!!

  Read the article

• Two routers in a LAN

  - by taxi

  router A no wifi +--- pc01 +--- pc02 | +--- router B wifi +--- pc03 +--- printer In my LAN I have a modem-router (say A) (no wifi connection) acting as DHCP server, and connected to the Internet. Now, I want to add another router (say B) (with wifi connection) to the LAN, in order to connect wifi pc's and net printers. Here I would disable DCHP server functionality. Is it correct to connect router B to router A via an ethernet port? In router A I define an IP address (eg 192.168.1.100) to be assigned to router B (MAC address). I expect to see router B listed as an attached device, in router A's status, but on the contrary it is not listed.

  Read the article

• Connecting via url to a server that is on the same network as me

  - by Axehead

  Good day, I'm having problems with the ftp server I've just set up. I've already managed to configure my modem and wireless router to open up port 21 and setup ftp in my server. But It seems that when I try to connect to it when I'm in the same network as the server via URL, (ftp://mydomain.com) it redirects me to the modem's web interface. But then when I try to connect to it outside the network using a different internet connection. It succeeds. It also succeeds when I'm in the same network and I go to ftp://192.168.., the server's local IP. Am I supposed to adjust something in the modem or router? Or is this a different problem altogether? BTW I'm using Windows Server 2008 r2 as my server's OS and using IIS for ftp.

  Read the article

• Cisco WLAN Controller not pushing out DHCP addresses, what else could it be?

  - by Name

  On our Cisco WLAN Controller web interfaces, in Controller Interfaces, I have made a new interface with these settings: VLAN Identifier 202 IP Address 172.16.202.1 Netmask 255.255.255.0 Gateway 172.16.202.254 Primary DHCP Server 172.16.100.3 Secondary DHCP Server 172.16.100.2 Port: LAG I've also made a new WLAN and assigned it to the above interface. I have saved changes. But our wireless devices, although they seem to authenticate with the WLAN fine, they always get stuck on "obtaining DHCP address", so it seems the WLAN Controller isn't pushing out DHCP addresses to our devices. We do have a DHCP scope for the above in Windows Server 2008 R2 and everything there seems fine. If I connect a device with a static address (e.g. 172.16.202.10), it will connect. Stuck on what to do :(

  Read the article

• Filtering downloading a file

  - by Ozgun Sunal

  people. i know there are several types of firewalls operating at different layers of OSI. ACLs(layer 3 firewalls filter based on port numbers and IP addresses), SPI(which examines the patterns of data at layer 3 and realise that data content is malicious or not) and application layer firewalls which is capable of understanding the data at that level. Considering this, i'll give an example and learn what i need to do. Lets say, we have a computer has access to the Internet. i want to download a file or display a web page from a website but block access to the another website/s or downloading. To do this, i cant block access to the web browser on the 3rd party firewall bcos that will shut down all access. ACLs wont already do it. So, which kind of firewall will make it possible to filter specific traffic and how?

  Read the article

• What is the "real" difference between a NAS and NFS? Or, why pick a NAS device over "mere" NFS?

  - by warren

  From an end-user perspective, what is the difference between a NAS device and using NFS exports from a file server? They seem to accomplish the same end result. The difference between a SAN and other file storage is related (in my experience) to how they are connected to the server infrastructure. However, the difference between a NAS, connecting over a standard ethernet port, and NFS (sharing storage off specific servers, also over the network), seems more nebulous. Is there a good reason to pick a NAS filer over just running NFS on servers?

  Read the article

• Network connectivity issue

  - by kubiej21

  I am a novice cisco user and I am trying to investigate as to why one of our connections went down. We have a fiber network ring that is operating just fine. Connected to this ring via ethernet, is a lone 3560. This connection has worked flawlessly for the past year and a half. This morning, I noticed that I could not connect to that remote switch. I checked the configurations on both switches, and nothing has changed (as I expected). In the field, the port lights were flashing, indicating that some sort of communication is occurring. There is only 1 ethernet cable that has been run between these two locations, so testing an alternate path is not possible. What else can I do to fix this connection?

  Read the article

• Can you use a DVI-VGA Adapter on a monitor instead of a video card?

  - by Joel Coehoorn

  I suspect the answer to this is "no", but here goes: I have a monitor with inputs for DVI and VGA. I want to be able to share this display with two computers (one at a time, of course) that both have VGA only. I also have a DVI-VGA dongle that came with a video card that's in a different computer. Can I connect this dongle directly to the DVI port on the monitor so that I can connect both VGA computers? I'd rather not resort to a kvm.

  Read the article

• Stopped windows firewall service during ICS, how is this possible?

  - by insipid

  Although windows firewall is required to be on when you "start" Internet Connection Sharing, you can stop the WF service with MMC. When done a client can still use the host machines internet. The firewall had port 80/http blocked, and now it is open for incoming traffic. However other ports used by applications on the host and client which communicate with each other still seem to be blocked. Can anybody explain what might be happening here? Doesn't ICS need windows firewall for NAT? Note: I am not actually seeing anything in the firewall logs after stopping the service, but even packets sent localhost on the host machine never arriving on these other random ports.

  Read the article

• Where can I connect this USB 3.0 cord?

  - by tomsawyer95

  My motherboard has 2 USB 3.o slots in the back, where the usual slots go, but the tower also supports 1 or 2 USB 3.0 ports in the front, above the DVD drive. So, there is a cord coming out of those ports that has an end exactly like the one in the attached picture. I am not able to find a matching port on the mobo, so I presume it doesn't have one, and I would need an adapter or else just leave it inoperable. I have an ASUS P8Z68-V LX and an Antec 900 tower.

  Read the article

< Previous Page | 369 370 371 372 373 374 375 376 377 378 379 380  | Next Page >