Search Results

Search found 11973 results on 479 pages for 'ip conflict'.

Page 376/479 | < Previous Page | 372 373 374 375 376 377 378 379 380 381 382 383  | Next Page >

• Problem connecting to isp server using xl2tpd as client. Ubuntu server 13.04

  - by Deon Pretorius

  I have followed guides found on google and ubuntu support pages and can get xl2tpd connection up but only under the following conditions: 1 - ADSL model must be configured and connected to the ISP or 2 - ADSL modem in bridge mode I must have an existing PPPoe connection established. If neither of the above are active xl2tpd wont trigger pppd and connect to the isp and thus tunnel connection fails to connect to the L2TP server of the ISP. Am I doing something wrong; /etc/ppp/options.l2tpd.axxess ipcp-accept-local ipcp-accept-remote refuse-eap refuse-chap require-pap noccp noauth idle 1800 mtu 1200 mru 1200 defaultroute usepeerdns debug lock connect-delay 5000 name (name used for ppp connection) /etc/ppp/pap-secrets # * password (name used for ppp connection as above) * (ppp password supplied by isp) /etc/xl2tpd/xl2tpd.conf [global] ; Global parameters: auth file = /etc/xl2tpd/l2tp-secrets ; * Where our challenge secrets are access control = yes ; * Refuse connections without IP match debug tunnel = yes [lac axxess] lns = 196.30.121.50 ; * Who is our LNS? redial = yes ; * Redial if disconnected? redial timeout = 5 ; * Wait n seconds between redials max redials = 5 ; * Give up after n consecutive failures hidden bit = yes ; * User hidden AVP's? length bit = yes ; * Use length bit in payload? require pap = yes ; * Require PAP auth. by peer require chap = no ; * Require CHAP auth. by peer refuse chap = yes ; * Refuse CHAP authentication require authentication = yes ; * Require peer to authenticate name = BLA85003@axxess ; * Report this as our hostname ppp debug = yes ; * Turn on PPP debugging pppoptfile = /etc/ppp/options.l2tpd.axxess ; * ppp options file for this lac /etc/xl2tpd/l2tp-secrets # Secrets for authenticating l2tp tunnels # us them secret # * marko blah2 # zeus marko blah # * * interop * vzb_l2tp (*** secret supplied by isp) ^ isp server host name Any help will be greatly appreciated

  Read the article

• Reverse WiFi to Broadcast connection coming from a USB device

  - by Daniel Clem

  I am using the app called Clockworkmod Tether. It connects using a script ( command line " gksu ./run.sh " ) on the computer. All my programs connect to the internet perfectly, minitube, midori, transmission torrents. But the network manager does not show any connection, wired or wireless. So this may cause issues? What I want to do is take this connection, and be able to share it some way, any way, by wireless. This Acer Timeline "Aspire 5810TZ" does have an Ethernet, so wired out to a router might be an option. But I would prefer to simply reverse the Wireless card to broadcast out to about 2 or 3 devices. Is this possible? Yes I have taken a look at the other questions already posted here, but the answers are 1 year old or older, and not clear at all. I am moderately comfortable (4.5 out of 10 ) on the command line. But pretty much need line by line directions for what commands are needed and what order, ect. Edit I have already tried the method of "Left click network manager, Create New Wireless Network" It is created fine, and I am able to connect to it with a tablet, but am un-able to get an outside connection with it. Using the "Shared to other computers" option because DHCP doesn't seem to work, and WEP Passphrase Security. I get an IP address on the connected device. But as I said, won't bring up any outside webpages or the like. So perhaps this is the wrong approach?

  Read the article

• Bad archive mirror using PXE boot method

  - by user11566

  I'm trying to automatically install Ubuntu on a client PC by using the PXE BOOT method....my Objectives are below: I am following the steps given in this link installation using PXE BOOT the server will have a KICKSTART config file which contains the parameters for the OS installation and the files which are required for the OS installations. the client will have to detect this configuration along with the setup files and complete the installation without any input from the user. In my server I have installed DHCP3-server,Apache2 and TFTP to help me with the installation. I have nearly achieved my first objective, I am able to boot my client using the files stored in the server but during the installation stage it is asking me to CHOOSE A MIRROR OF UBUNTU ARCHIVE I gave the server's IP address and the path in the server where the files are located but then its giving me this error BAD ARCHIVE MIRROR So is it possible that instead of downloading all the files from the internet and storing them on my disk can I use the files which comes with the UBUNTU-CD, and how to store these files in what format (should I zip them) on the disk? secondly I am also generating the ks.cfg which I wanted to give to the client for automatic installation of the OS. So how should the configuration file be given to the installation process?

  Read the article

• Can't Start ISC DHCP IPv6 Server

  - by MrDaniel

  Trying to enable the ISC DHCP server for just IPv6 on Ubuntu 12.04 LTS. I have downloaded and installed the DHCP server via the following command: $ sudo apt-get install isc-dhcp-server Then I have followed the instructions in the following resources, Ubuntu Wiki DHCPv6, SixXS - Configuring ISC DHCPv6 Server and Linux IPv6 HOWTO - Configuration of the ISC DHCP server for IPv6 . So from review all those resources it seems like I need to: set a static IPv6 address for the Interface I want to run the DHCPv6 server from that is part of the IPv6 network subnet outside the DHCP range. Edit the /etc/dhcp/dhcpd6.conf file to configure the DHCPv6 range etc. Create the /var/lib/dhcp/dhcpd6.leases Manually start the DHCPv6 server. Setting the Static IP for eth0 $ sudo ifconfig eth0 inet6 add 2001:db8:0:1::128/64 My dhcpd6.conf default-lease-time 600; max-lease-time 7200; log-facility local7; subnet6 2001:db8:0:1::/64 { #Range for clients range6 2001:db8:0:1::129 2001:db8:0:1::254; } Created the dhcpd6.leases file As indicated in the dhcpd.leases man page. $ touch /var/lib/dhcp/dhcpd6.leases #Tried with sudo as well Manually starting the DHCPv6 server. Attempted to start the server using the following command: $ sudo dhcp -6 -f -cf /etc/dhcp/dhcpd6.conf eth0 The problem, the DHCP will not start, with an append error for the dhcpd6.leases file as indicated below when running the manual start command noted above. Can't open /var/lib/dhcp/dhcpd6.leases for append. Any ideas what I might be missing?

  Read the article

• Cannot ping any computers on LAN

  - by Timothy

  I havem't been able to find a straight forward answer on this yet. I'm hoping people here are able to help! Keep in mind that I'm a complete beginner at this - this is the first installation i've done for any LINUX systems ever so please keep that in mind when answering this question. We are a complete Windows shop, using nothing but Microsoft products but looking into the value of OpenStalk however have been having problems getting Ubuntu Server installed and speaking to the network. The machine is getting an IP address which is telling me that some sort of DHCP activity is working but I'm not able to ping any computer on our network as well as not able to connect to the internet. Every time I try to ping i'm getting; Destination Host Unreachable I've tried using modifying the resolv.conf file with our static details to match my Windows 7 machine still with no luck. Even tried disabling the firewall on Ubuntu Server 11 and no luck. Any ideas? Please let me know if there is any information you need from the server and I'll post up.

  Read the article

• Reproducible freezes with on an AMD fusion (e350) sony vaio

  - by doycho

  So a week ago I bought it and I've been struggling to make the Ubuntu which I installed stable. There's one thing that makes my life miserable, though. There's this easily reproducible freeze when I start some kind of video. So here is what happens: Everything works fine for some time I start vlc/mplayer/flashplayer/totem with something to watch In few minutes time I lose the sound (nothing in the logs at this point) At that time the video app instantly allocates all the memory and its CPU usage skyrockets. Total freeze. I can move the cursor around for few seconds and sometimes even switch to another app. But ultimately there comes the time I can't do anything - can't kill X with ctrl+alt+backspace (I have it enabled), can't switch to any other console (ctrl+alt+f1-6), can't connect to the machine via ssh. The only way to restart it is the ctrl+alt+SysRq+UABI magic :) What discourages me most is the fact I can't see anything in the logs. The only error I've noticed is Jun 19 17:00:37 serenity kernel: [ 1506.350676] software-center[17581]: segfault at 30 ip 00007fd3631b814c sp 00007fff18a6fa10 error 4 in libgtk-x11-2.0.so.0.2400.4[7fd362f7d000+436000]. I've been searching through the Xorg log, kernel logs, syslog. If you have any idea how I can get more debug info I'll be glad to try them. Things I've tried: Changing drivers - the open source one, the proprietary driver xorg-edgers' ppa - https://launchpad.net/~xorg-edgers/+archive/ppa changing to the last stable kernel (2.6.39) Some notes: It my be irrelevant but the sound is constantly stuttering. This probably is a separate issue though I've found that if I start more video/sound apps the freeze happens faster.

  Read the article

• What does the crash mean? And why is my Ubuntu Blackbox is crashing how can i check deeply?

  - by YumYumYum

  My system was running for a while amount of 6 hour. Two times i loss remote access and it was not functioning anymore IP is gone etc etc. 3 time showing crash but i have no idea what and why. How to know what went wrong? $ last sun pts/0 d51a429c9.access Mon Mar 19 13:44 still logged in sun tty7 :0 Mon Mar 19 12:17 still logged in reboot system boot 2.6.38-8-generic Mon Mar 19 12:17 - 13:49 (01:31) sun pts/0 d51a429c9.access Mon Mar 19 10:05 - crash (02:12) sun tty7 :0 Mon Mar 19 10:00 - crash (02:16) reboot system boot 2.6.38-8-generic Mon Mar 19 10:00 - 13:49 (03:48) sun pts/0 d51a429c9.access Mon Mar 19 09:24 - down (00:35) sun tty7 :0 Mon Mar 19 09:20 - down (00:39) reboot system boot 2.6.38-8-generic Mon Mar 19 09:20 - 10:00 (00:39) sun pts/2 d51a429c9.access Sun Mar 18 18:04 - down (01:14) sun pts/1 d51a429c9.access Sun Mar 18 17:43 - down (01:35) sun pts/0 d51a429c9.access Sun Mar 18 15:07 - 18:47 (03:40) sun pts/1 d51a429c9.access Sun Mar 18 12:58 - 17:42 (04:43) sun pts/0 d51a429c9.access Sun Mar 18 10:21 - 15:06 (04:44) sun tty7 :0 Sun Mar 18 08:56 - down (10:22) reboot system boot 2.6.38-8-generic Sun Mar 18 08:56 - 19:19 (10:22) sun tty7 :0 Sat Mar 17 18:03 - down (14:51) reboot system boot 2.6.38-8-generic Sat Mar 17 18:03 - 08:55 (14:51) sun tty7 :0 Sat Mar 17 15:00 - down (01:38) reboot system boot 2.6.38-8-generic Sat Mar 17 15:00 - 16:39 (01:38) sun pts/0 d51a4297d.access Sat Mar 17 10:45 - 14:32 (03:46) sun tty7 :0 Fri Mar 16 18:46 - crash (20:14) reboot system boot 2.6.38-8-generic Fri Mar 16 18:46 - 16:39 (21:53) $ sensors acpitz-virtual-0 Adapter: Virtual device temp1: +27.8°C (crit = +100.0°C) temp2: +29.8°C (crit = +100.0°C)

  Read the article

• How can I use domain masking without having self referral in Google Analytics

  - by Cdore

  I have one old domain that points to a website's server's ip (let's call it www.oldsite.com). I have a new one, www.newsite.com, that is set up to be forwarded to a specific page on the website. Due to the way the host of newsite.com places the website in a frame, in Google Analystics, the newsite.com is listed as a source rather than the source they were at before hand, causing a self referral. A solution is to edit the code of the iframe as I looked up, but there's no way to really edit the host's masking source code of course. Another solution I did previously was have www.newsite.com point to the address that www.oldsite.come pointed to. It solved the analytics problems, but in exchange, the url masking no longer worked. In the address bar, it came up as www.oldsite.com. Is there a way to make me have url masking and be able to forward to agree with google analytics? The server of the website is hosted on a cloud server, if this is anymore information.

  Read the article

• Need help with cybersquatting complaint: can a domain name forward AND resolve at same time? [on hold]

  - by Alan

  Probably a silly question for you pros... but for this novice here, I just want to make sure my understanding is correct. Context: I am trying to prove that a domain name owner has been cybersquatting and has never used the domain name in question. There are 4 shots from WayBackMachine over a three-year period that show the domain name resolving to a basic server index page with either no files or a single cgi-bin folder. The domain name owner claims, however, that the domain name was forwarded over the entire time from to another website, and that these captures probably coincided with occasional "outages." It is my understanding that: a) domain name forwarding is binary: if a domain name is forwarded to a valid site, it cannot simultaneously resolve to a valid IP address. Is this correct? b) domain name forwarding is not subject to "outages": servers can have outages, and websites can be down, but the forwarding itself cannot be down, as this is simply a pointer. (Or, the entire registrar where the DNS settings are hosted would have to malfunction. Is this correct? FINALLY, bonus question for pro webmasters: What is the likelihood that the WayBackMachine would capture the domain name on just those occasions when the webmaster disabled forwarding to supposedly work on the new site? Mucho thanks in advance!

  Read the article

• Dell inspiron not finding Vodafone router

  - by Jeggy

  I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

  Read the article

• Linux,Apache,NetBeans,PHP == Windows,IIS/Cassini,Visual Studio,ASP.Net

  - by Neil Smith

  I've worked out how to get my linux based Netbeans PHP development machine to behave much like what happens when you create a new ASP.Net project in Visual Studio. Firstly create multiple PHP project in Netbeans,say for example mysite1 and mysite2. Next edit the apache2/sites-enabled/000-default file and add two virtualhost sections as below <VirtualHost 127.0.1.1> ServerName mysite1.localhost DocumentRoot /var/www/mysite1/ </VirtualHost> <VirtualHost 127.0.2.1> ServerName mysite2.localhost DocumentRoot /var/www/mysite2/ </VirtualHost> For each site you add, pick a different ip address similar to the above where I use the third octet to increment, next edit the etc/hosts file and add the following two lines 127.0.1.1 mysite1.localhost 127.0.2.1 mysite2.localhost Then in Netbeans, go to File->Project Properties click on 'Run Configuration' and set 'Project Url' to http://mysite1.localhost for the first project and http://mysite2.localhost for the second project. That will give you a PHP development box which develops multiple PHP projects similar to how a Visual Studio Windows based box handles multiple ASP.Net sites. Hope this helps someone :)

  Read the article

• Unable to print login-required images in IE

  - by Tim Fountain

  I have some images in a section of a site that require the user to be logged in in order to view. These images are served by a PHP script, which checks the user's login state and if valid, serves the binary data with the appropriate headers. This all works fine. The issue comes when a user tries to print one of these images. In Internet Explorer, when they go to print preview they get the broken image box with a red cross in the corner instead of the actual file. This is what gets printed also. All other browsers can print the images without issue. I have some images elsewhere on the site that are also served via. PHP but these don't require a login. These print fine. The PHP-powered HTML pages on the site that require a login also print fine in IE. It's just login-required images. The user hitting print preview does not seem to result in additional HTTP request to the server for the file. However I do see an additional HTTP request a few seconds later that comes from the same IP (may or may not be related), This request includes no host header, no REQUEST_URI and no user agent. The 'please login' page sends an appropriate 403 header. I've also added a far-in-future expires header to the image response itself to ensure that browsers can serve/print the files from their own cache but this hasn't made any difference. Why can't IE print the images and what else can I do to investigate or fix the problem?

  Read the article

• How should I structure my database to gain maximum efficiently in this scenario?

  - by Bob Jansen

  I'm developing a PHP script that analyzes the web traffic of my clients websites. By placing a link to a javascript on the clients website (think of Google Analyses), my script harvests information like: the visitors IP address, reference link, current page link, user agent, etc. Now my clients can view these statistics via a control panel that I have build. These clients can also adjust profile settings, set firewall rules, create support tickets and pay invoices. Currently all the the traffic is stored in one table. You can imagine that this tabel would become very large as some my clients receive thousands of pageviews per day. Furthermore, all the traffic data of each client would be stored in the same table, creating a mess. This is the same for the firewall rules currently, and the invoice and support system. I'm looking for way to structure my database in a more organized way to hold large amounts of data of multiple users. This is the first project that I'm developing that deals with so much data, and would like to hear suggestions and tips. I was thinking of using multiple databases to structure the data. The main database will store users data (email,pass,id,etc) admin/website settings. Than each client will have an unique database labeled prefix_userid, which carry tables holding their traffic, invoice, and support ticket data. Would this be a solution, and would it slow down or speed up overall performances (that is spreading the data over muliple databases). I have a solid VPS, but would like to safe and be as effient as possible.

  Read the article

• MySQL - Configuration

  - by Stuart Brierley

  Having previously detailed how to install MySQL Server, the next step is configuring MySQL. The MySQL configuration wizard can either be run immediately following installation from the MySQL installation wizard or manually from the Start Menu. Following the splash screen you can then choose whether to run a detailed or standard configuration. The detailed configuration allows you to create the optimal configuration for your specific machine, whereas the standard configuration creates a general configuration that can then be manually tuned. I chose detailed.   You are then asked to choose the type of server instance that is being configured. In this case it is a developer machine. Following this you are asked to choose the type of database usage that you expect on the server. I opted for multifunctional. You must then specify the location of the InnoDB tablespace.   Next specify the number of concurent connections to the server.   Now you must configure the networking options. I left the Strict mode enabled as this is the recommended option, but I disabled TCP/IP networking as I wanted to restrict this MySQL installation to the local machine only.   Set the character set that is best suited to your use - for me this was the default standard character set. Next up is the option to run MySQL as a service and whether or not to include the mysql dircetories in the windows PATH. I kept the install as a windows service option enabled, but unchecked the Launch MySQL server automatically option. This is because I only wanted MySQL running when I specifically want to use it. I also enabled the include in windows PATH option.   You can then change the security settings for the mysql installation. I opted to change the root password, disable root from local machines and disable annoymous access.   You are now ready to execute the configuration.   Once completed you should hopefully see the completed screen with lots of nice ticks against the various configuration tasks.

  Read the article

• Spotlight on GlassFish 4.1: #7 WebSocket Session Throttling and JMX Monitoring

  - by delabassee

  'Spotlight on GlassFish 4.1' is a series of posts that highlights specific enhancements of the upcoming GlassFish 4.1 release. It could be a new feature, a fix, a behavior change, a tip, etc. #7 WebSocket Session Throttling and JMX Monitoring GlassFish 4.1 embeds Tyrus 1.8.1 which is compliant with the Maintenance Release of JSR 356 ("WebSocket API 1.1"). This release also brings brings additional features to the WebSocket support in GlassFish. JMX Monitoring: Tyrus now exposes WebSocket metrics through JMX . In GF 4.1, the following message statistics are monitored for both sent and received messages: messages count messages count per second average message size smallest message size largest message size Those statistics are collected independently of the message type (global count) and per specific message type (text, binary and control message). In GF 4.1, Tyrus also monitors, and exposes through JMX, errors at the application and endpoint level. For more information, please check Tyrus JMX Monitoring Session Throttling To preserve resources on the server hosting websocket endpoints, Tyrus now offers ways to limit the number of open sessions. Those limits can be configured at different level: per whole application per endpoint per remote endpoint address (client IP address)   For more details, check Tyrus Session Throttling. The next entry will focus on Tyrus new clients-side features.

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• Prevent Click Fraud in Advertisement system with PHP and Javascript

  - by CodeDevelopr

  I would like to build an Advertising project with PHP, MySQL, and Javascript. I am talking about something like... Google Adsense BuySellAds.com Any other advertising platform My question is mainly, what do I need to look out for to prevent people cheating the system and any other issues I may encounter? My design concept. An Advertisement is a record in the Database, when a page is loaded, using Javascript, it calls my server which in turn will use a PHP script to query the Database and get a random Advertisement. (It may do kore like get an ad based on demographics or other criteria as well) The PHP script will then return the Advertisement to the server/website that is calling it and show it on the page as an Image that will have a special tracking link. I will need to... Count all impressions (when the Advertisement is shown on the page) Count all clicks on the Advertisement link Count all Unique clicks on the Advertisement link My question is purely on the query and displaying of the Advertisement and nothing to do with the administration side. If there is ever money involved with my Advertisement buying/selling of adspace, then the stats need to be accurate and make sure people can't easily cheat the system. Is tracking IP address really the only way to try to prevent click fraud? I am hoping someone with some experience can clarify I am on the right track? As well as give me any advice, tips, or anything else I should know about doing something like this?

  Read the article

• CodePlex Daily Summary for Thursday, July 31, 2014

  CodePlex Daily Summary for Thursday, July 31, 2014Popular ReleasesDbEntry.Net (Leafing Framework): DbEntry.Net 4.2: DbEntry.Net is a lightweight Object Relational Mapping (ORM) database access compnent for .Net 4.0+. It has clearly and easily programing interface for ORM and sql directly, and supoorted Access, Sql Server, MySql, SQLite, Firebird, PostgreSQL and Oracle. It also provide a Ruby On Rails style MVC framework. Asp.Net DataSource and a simple IoC. DbEntry.Net.v4.2.Setup.zip include the setup package. DbEntry.Net.v4.2.Src.zip include source files and unit tests. DbEntry.Net.v4.2.Samples.zip ...Recaptcha for .NET: Recaptcha for .NET v1.5: What's NewMinor bug fixes Support for legacy .NET framework 4.0 and ASP.NET MVC 4. Support for .NET Framework 4.5.1.Azure Storage Explorer: Azure Storage Explorer 6 Preview 1: Welcome to Azure Storage Explorer 6 Preview 1 This is the first release of the latest Azure Storage Explorer, code-named Phoenix. What's New?Here are some important things to know about version 6: Open Source Now being run as a full open source project. Full source code on CodePlex. Collaboration encouraged! Updated Code Base Brand-new code base (WPF/C#/.NET 4.5) Visual Studio 2013 solution (previously VS2010) Uses the Task Parallel Library (TPL) for asynchronous background operat...Wsus Package Publisher: release v1.3.1407.29: Updated WPP to recognize the very latest console version. Some files was missing into the latest release of WPP which lead to crash when trying to make a custom update. Add a workaround to avoid clipboard modification when double-clicking on a label when creating a custom update. Add the ability to publish detectoids. (This feature is still in a BETA phase. Packages relying on these detectoids to determine which computers need to be updated, may apply to all computers).VG-Ripper & PG-Ripper: PG-Ripper 1.4.32: changes NEW: Added Support for 'ImgMega.com' links NEW: Added Support for 'ImgCandy.net' links NEW: Added Support for 'ImgPit.com' links NEW: Added Support for 'Img.yt' links FIXED: 'Radikal.ru' links FIXED: 'ImageTeam.org' links FIXED: 'ImgSee.com' links FIXED: 'Img.yt' linksDynamics AX Development tools: Version 1.0.0: Alpha release of the package. I am just combining greate community tools into a package. I have not go through testing every function of the tools. However, feel free to point out if you found any bugs!Asp.Net MVC-4,Entity Framework and JQGrid Demo with Todo List WebApplication: Asp.Net MVC-4,Entity Framework and JQGrid Demo: Asp.Net MVC-4,Entity Framework and JQGrid Demo with simple Todo List WebApplication, Overview TodoList is a simple web application to create, store and modify Todo tasks to be maintained by the users, which comprises of following fields to the user (Task Name, Task Description, Severity, Target Date, Task Status). TodoList web application is created using MVC - 4 architecture, code-first Entity Framework (ORM) and Jqgrid for displaying the data.Waterfox: Waterfox 31.0 Portable: New features in Waterfox 31.0: Added support for Unicode 7.0 Experimental support for WebCL New features in Firefox 31.0:New Add the search field to the new tab page Support of Prefer:Safe http header for parental control mozilla::pkix as default certificate verifier Block malware from downloaded files Block malware from downloaded files audio/video .ogg and .pdf files handled by Firefox if no application specified Changed Removal of the CAPS infrastructure for specifying site-sp...SuperSocket, an extensible socket server framework: SuperSocket 1.6.3: The changes below are included in this release: fixed an exception when collect a server's status but it has been stopped fixed a bug that can cause an exception in case of sending data when the connection dropped already fixed the log4net missing issue for a QuickStart project fixed a warning in a QuickStart projectYnote Classic: Ynote Classic 2.8.5 Beta: Several Changes - Multiple Carets and Multiple Selections - Improved Startup Time - Improved Syntax Highlighting - Search Improvements - Shell Command - Improved StabilityHead First C#: The Quest: The Quest: Stable release of "The Quest" game ( Lab 2 from Head First C#, 3rd edition)TCP/IP Adapter BizTalk 2013: TCPIP Adapter for BizTalk 2013 - Version 1.0: Version 1.0 This is an updated version of the BizTalk 2010 TCP/IP adapter. References have been updated and a new setup (ISLE) has been used. Follow the installation instructions below to install the adapter. Still want to automate step 4, but haven't got to it yet. Installation instructions Make sure to close the BizTalk Administration Console. Just to make sure everything gets refreshed after installation. Download and install the setup. The setup makes sure the adapter will be regis...gicon: gicon HTTP service v1.0.0: core: 1.0.0.26592 service: 1.0.0.27190 Github: http://rynnwang.github.io/gicon/ Github.io: http://rynnwang.github.io/gicon/ Codeplex: http://gicon.codeplex.com .NET required: 2.0 or above. Installation notes: 1. You need to run intallutil command to install ifunction.GuidIconHttpService.exe file as Windows Service 2. You need to update ifunction.GuidIconHttpService.exe.config file in the folder to set correct HTTP URI prefixes. In release zip by default, it is set as http://localhost:20000...TEBookConverter: 1.2: Fixed: Could not start convertion in some cases Fixed: Progress show during convertion was truncated Fixed: Stopping convertion didn't reset program titlenewmail_OutlookCOM: newmail_OutlookCOM: First Stable ReleaseSharePoint - Data View Web Part Documenter: Data View Web Part Documenter 1.0: .NET Framework 4 Client Profile required for this to run on your PC. Please see the documentation for running the tool.LOL zmena skinu klienta: LOL jednoduchý menic skinu klienta: Jednoduchý prográmek, který ušetrí cas pri zmene klienta. Nemusí se proklikáva18541855 adresáru :)SSRS Plus+: Latest - SSRS Plus Application and Source Code: This release contains the Beta version with significant changes in comparison to the old release which I am keeping for legacy reasons. At some point a changeover will be made once it has been confirmed that my branch is stable and Mr Bagwan is in agreement also.CS-Script Source: Release v3.8.4: CSScript.Evaluator is migrated to Mono v3.3.0 Added aggregating //css_ignore_ns from the imported scripts cs-script.7z - CS-Script Suite (binaries, documentation, samples) cs-script.ExtensionPack.7z - CS-Script Extension Pack (additional binaries and samples) cs-scriptDocs.7z - CS-Script DocumentationDotSpatial: DotSpatial 1.7: DotSpatial.Full - includes all DotSpatial libraries, extensions and DemoMap application DotSpatial.Core - includes only DotSpatial core libraries Entire list of changes see in the issue tracker. Main changes: Improved common stability, optimized memory and speed when loading and rendering shapefiles, fixed some memory leaks in rasters and shape layers. Simplified plugin infrastructure. Now there are predefined implementations for all required components (IStatusControl, IDockManager, IHead...New ProjectsBrilliantORM: ????ORM??，??SQL?????????。???????????。Crafter: ?????? ??? ????Dotnetnuke xblog // Blog, Article, Events, Documents: xBlog is a blog program based on DNN, it has powerful functions and unique design style. In addition to article management function which common blog module hasIn Plain Sight: Embedding plain text into an image so one can hide the text "In Plain Sight". A cursory view into the world of Steganography.JS Koans Visual Studio Friendly Version: A Version of JS koans loaded into Visual StudioMy Troop First: just adding to the siteOFX Parser: Biblioteca desenvolvida em C# que traduz arquivos OFX e gera a instância de uma classe que representa o arquivo. Um exemplo de uso está disponível, assim como aOrchard Custom Code module: This module adds a very simple tool to add custom code in front-end pages head and foot.SPB Export to KeePass Import Conversion: A simple script to convert the .xml-file by konste's "SPB Wallet Export" (https://spbwalletexport.codeplex.com/) into an import format accepted by KeePass 2The unTroublemaker: The unTroublemaker is a troubleshooter program that helps your project quickly find and fix missing dependency issues using simple XML-based specifications.

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• Case study: LOREX Technology Increases Website Traffic 90% with Oracle ATG

  - by Richard Lefebvre

  LOREX Technology Increases Website Traffic 90% by Enhancing the Online Customer Experience with a Flexible E-Commerce Platform LOREX Technology Inc. provides businesses and consumers with advanced video surveillance security products under the LOREX and Digimerge brands. LOREX, which caters to midsize business and consumer markets, is available in thousands of retail locations across North America. The Digimerge division sells its products through security system distributors in North America. Both brands concentrate on the sale of wired, wireless, and IP security surveillance and monitoring equipment, including cameras, digital video recorders, and all-in-one systems. LOREX conducted an extensive search for the right e-commerce platform to address its immediate need for a more intuitive shopping cart interface that could grow along with the company. After reviewing other solutions, including open source, LOREX chose Oracle ATG Web Commerce because it addressed every stage of the buying process and crossed all customer touch points, including the Web, contact center, mobile devices, social media, and its B2B partners’ physical stores. LOREX also found that Oracle ATG Web Commerce’s functionality was more robust than competing options, and it offered an attractive total cost of ownership. “Oracle ATG Web Commerce provided an optimal foundation to support rapid, scalable, long-term business growth while allowing full control of the platform,” said Sufi Khan Sulaiman, director, E-Commerce and Digital, LOREX. Read full story here  

  Read the article

• Are webhosts that require NS instead of a CNAME common?

  - by billpg

  I've just signed up with a webhost (which I prefer not to name) and I'm reasonably happy with it. The only nit was when I was ready to put a site online and I asked the support line to what name I should point my 'www' CNAME to. They responded that they don't do that and I need to set my domain's NS records for the hosting to work. "Why would you ever want to do it that way? Our service to you includes DNS and our servers are probably much better than the one your registrar provides." This was a bit of surprise as all of the other webhosts I've worked with happily support this. I've set up (eg) gallery.myfriend.example for friends by having them configure their DNS to CNAME 'gallery' to the name of a shared server at a webhost and the webhost does name-based hosting for 'gallery.myfriend.example'. (Of course, if the webhost ever tells me I'm being moved from A.webhost.example to B.webhost.example, it would be my responsibility to change where the CNAME points. Really good webhosts would instead create myname.webhost.example for the IP of whichever server my stuff happens to be on, so I'd never have to worry about keeping my CNAME up to date.) Is my impression correct, that most webhosts will happily support a service that begins with a CNAME hosted elsewhere, or is it really more common that webhosts will only provide a service if they control the DNS service too?

  Read the article

• Wired connection problem through router

  - by tommypincha

  I'm having trouble to connect my Ubuntu 11.10 to internet through ethernet. I installed a router to get Wi-Fi and now (by a wired connection) I can't have internet with ubuntu (but I can with Windows 7). I see several attempts per minute of the network-manager to get a connection, but after a minute it stops trying. Here are a couple of outputs from key files: cat /etc/network/interfaces auto lo iface lo inet loopback and ifconfig -a eth0 Link encap:Ethernet HWaddr 00:16:76:e4:a6:e8 inet6 addr: fe80::216:76ff:fee4:a6e8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:117 dropped:0 overruns:0 frame:117 TX packets:50 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:12221 (12.2 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:582 errors:0 dropped:0 overruns:0 frame:0 TX packets:582 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:46024 (46.0 KB) TX bytes:46024 (46.0 KB) I tried reconnecting the modem and the router and reconnecting the ethernet cable but nothing... I tried other solutions from other posts (this one has a similar issue Wired connection not working) but again nothing. My IP is dynamic. A couple of things I see and did: I see no inet addr, only inet6. I ignored ipv6 from the internet connections, and restarted the network-manager service and nothing. A difference with the post I mentioned is the RX packets with errors I have, is this a clue of the problem? Any help would be appreciated, Thanks!

  Read the article

• Is it necessary to add an HP printer to CUPS using the hplip URI?

  - by JPbuntu

  I recently setup a CUPS print server (Ubuntu server 12.04) and I having trouble with performance of a HP Color LaserJet Printer CP3505n. The printer pauses for about a second between printing each page, which is annoying when there is a lot of printing to be done. This doesn't happen when the printer is installed directly to a Windows client. In an attempt to fix this I have setup the printer a couple different ways. I decided not to do a Samba share since this wiki said IPP is preferred. First Method Added to HP LaserJet to CUPS as a Discovered Network Printer, and selected HP Color LaserJet cp3505 hpijs pcl3, 3.12.2 (en) driver. I did not use a hplip URI. Second Method (hplip URI) I thought adding hplip to the mix might improve the performance, so I added the printer like this: Ran hp-setup -m 192.168.2.60, prompted to select driver Selected HP Color LaserJet cp3505 hpijs pcl3, 3.12.2 (en) Used hplip to generate a URI: hp-makeuri 192.168.2.60 Then added the printer to CUPS as a Local Printer: HP Printer (HPLIP), and entered: hp:/net/HP_Color_LaserJet_CP3505?ip=192.168.2.60. Either method I use I am able to share the printer on the network by adding a printer as http://192.168.2.2:631/printers/HP_LASER-TERRAC. Does it make a difference which way the printer is added cups? If so, and I install the printer with the hp URI, can I still change the driver using the CUPS web interface? I have been trying out different drivers to try and improve performance, and the cups interface is the easiest way to change them. Thanks in advance.

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

< Previous Page | 372 373 374 375 376 377 378 379 380 381 382 383  | Next Page >