Search Results

Search found 23950 results on 958 pages for 'ie8 64 bit'.

Page 389/958 | < Previous Page | 385 386 387 388 389 390 391 392 393 394 395 396  | Next Page >

• Windows doesn't get access to internet though linux easily does

  - by flashnik

  We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

  Read the article

• Slowdown upon router/modem setup change

  - by Ollie Saunders

  I’ve been using a Belkin FSD7632-4 modem router to connect to my TalkTalk provided ADSL internet connection for some time and been pretty happy with it. Recently, however, the connection has been failing and I decided to get a ASUS RT-N16 instead, which is also a much more capable router generally. The ASUS RT-N16 doesn’t come with a modem built-in so I purchased as Zoom modem as well. I’ve set them both up and am using them to post this message. But I’m a bit miffed to find that I get a significantly and consistently slower downstream rate from the new configuration than with the old Belkin. Belkin modem router: downstream: 3.45 mbps upstream: 0.73 mbps ASUS router + Zoom modem: downstream: 2.71 mbps upstream: 0.66 mbps Any ideas why this is? The really weird thing about this is that the Zoom supports ADSL2 and ADSL2+ but I don’t think the old Belkin does. At first I thought it might be due to the Zoom modem being limited to PPPoE instead of PPPoA, which my ISP supports, but then I tried using PPPoE with the Belkin and that still gave a high speed. I’m using VC-Mux encapsulation with both. VPI of 0 and VCI of 38. I pulled this data off the Zoom: Mode: ADSL2 Line Coding: Trellis On Status: No Defect Link Power State: L0 Downstream Upstream SNR Margin (dB): 12.3 11.8 Attenuation (dB): 43.0 24.9 Output Power (dBm): 12.9 0.0 Attainable Rate (Kbps): 3936 844 Rate (Kbps): 3194 840 MSGc (number of bytes in overhead channel message): 59 10 B (number of bytes in Mux Data Frame): 99 14 M (number of Mux Data Frames in FEC Data Frame): 2 16 T (Mux Data Frames over sync bytes): 1 8 R (number of check bytes in FEC Data Frame): 8 8 S (ratio of FEC over PMD Data Frame length): 1.9833 9.0594 L (number of bits in PMD Data Frame): 839 219 D (interleaver depth): 32 2 Delay (msec): 15 4 Super Frames: 15808 14078 Super Frame Errors: 0 4294967232 RS Words: 513778 111753 RS Correctable Errors: 126 4294967238 RS Uncorrectable Errors: 0 N/A HEC Errors: 0 4294967279 OCD Errors: 0 0 LCD Errors: 0 0 Total Cells: 1920175 237597 Data Cells: 205993 392 Bit Errors: 0 0 Total ES: 0 0 Total SES: 0 0 Total UAS: 34 0

  Read the article

• Which AMI to to use for Java/Tomcat/MySQL in Amazon EC2?

  - by Justin

  I originally posted this on stackoverflow.com and it was suggested serverfault.com might be a better place to ask this question. So here goes: I'm trying to determine which Amazon Machine Image (AMI) to use as my Virtual Server in Amazon's EC2. For now, I'll need to choose an AMI that complies with the AWS Free Usage Tier. I want to deploy a Java app that I've been developing using Eclipse on Windows XP, Tomcat 7 and MySQL 5.5. I'm aware that I can choose the Basic 32-bit Amazon Linux AMI. Then I'd manually install Tomcat and MySQL (does MySQL get installed on the image or separately on an Elastic Block Store (EBS)?). Here's the rub, I'm a bit of a Linux noob. I can start Tomcat and tail the logs and such on Linux but I'm not familiar with the install process for Tomcat and MySQL on Linux and commands like sudo and chmod. I'm happy to get more hands on with Linux but I'm short on time right now. Are there AMI's that already have Tomcat and MySQL bundled? The Request Instance Wizard shows 805 Community AMI's that are Free Tier Eligible. 51 of the Free Tier Eligible AMI's have "Tomcat" in their name. I'm willing to consider using Elastic Beanstalk but my research thus far hasn't found any discussion of using MySQL with Beanstalk. The discussions all seem to use Amazon's SimpleDB. Any advice is greatly appreciated.

  Read the article

• installed mongo using brew but stuck at prompt

  - by user50946

  I have installed mongo using brew on my mac. When I give mongo command I see this MongoDB shell version: 2.4.6 connecting to: test but it stays there and never give me command prompt back anyone else noticed something like this I have reinstalled with no luck. The issue is persistent thanks Logs ***** SERVER RESTARTED ***** Fri Oct 18 08:11:48.360 [initandlisten] MongoDB starting : pid=2081 port=27017 dbpath=/usr/local/var/mongodb 64-bit host=Asims-MacBook-Air.local Fri Oct 18 08:11:48.360 [initandlisten] db version v2.4.6 Fri Oct 18 08:11:48.360 [initandlisten] git version: nogitversion Fri Oct 18 08:11:48.360 [initandlisten] build info: Darwin minimountain.local 12.5.0 Darwin Kernel Version 12.5.0: Sun Sep 29 13:33:47 PDT 2013; root:xnu-2050.48.12~1/RELEASE_X86_64 x86_64 BOOST_LIB_VERSION=1_49 Fri Oct 18 08:11:48.360 [initandlisten] allocator: tcmalloc Fri Oct 18 08:11:48.360 [initandlisten] options: { bind_ip: "127.0.0.1", config: "/usr/local/etc/mongod.conf", dbpath: "/usr/local/var/mongodb", logappend: "true", logpath: "/usr/local/var/log/mongodb/mongo.log" } Fri Oct 18 08:11:48.361 [initandlisten] journal dir=/usr/local/var/mongodb/journal Fri Oct 18 08:11:48.361 [initandlisten] recover : no journal files present, no recovery needed Fri Oct 18 08:11:48.398 [websvr] admin web console waiting for connections on port 28017 Fri Oct 18 08:11:48.398 [initandlisten] waiting for connections on port 27017 Fri Oct 18 08:12:03.279 [signalProcessingThread] got signal 1 (Hangup: 1), will terminate after current cmd ends Fri Oct 18 08:12:03.279 [signalProcessingThread] now exiting Fri Oct 18 08:12:03.279 dbexit: Fri Oct 18 08:12:03.279 [signalProcessingThread] shutdown: going to close listening sockets... Fri Oct 18 08:12:03.279 [signalProcessingThread] closing listening socket: 9 Fri Oct 18 08:12:03.279 [signalProcessingThread] closing listening socket: 10 Fri Oct 18 08:12:03.280 [signalProcessingThread] closing listening socket: 11 Fri Oct 18 08:12:03.280 [signalProcessingThread] removing socket file: /tmp/mongodb-27017.sock Fri Oct 18 08:12:03.280 [signalProcessingThread] shutdown: going to flush diaglog... Fri Oct 18 08:12:03.280 [signalProcessingThread] shutdown: going to close sockets... Fri Oct 18 08:12:03.280 [signalProcessingThread] shutdown: waiting for fs preallocator... Fri Oct 18 08:12:03.280 [signalProcessingThread] shutdown: lock for final commit... Fri Oct 18 08:12:03.280 [signalProcessingThread] shutdown: final commit... Fri Oct 18 08:12:03.282 [signalProcessingThread] shutdown: closing all files... Fri Oct 18 08:12:03.282 [signalProcessingThread] closeAllFiles() finished

  Read the article

• Firefox: non-Vimperator way to do mouseless browsing?

  - by Peter Mortensen

  Is it possible to do efficient browsing with Firefox using only the keyboard (like in Opera)? By efficient I mean something faster than using TAB - this takes far too long. The arrow keys should be for navigation (in Opera it is Shift + arrow key). It can done with the Vimperator add-on, but isn't there a simpler way? Update 2: the closest to Opera's way is to enable caret navigation (F7 toggles this mode). It doesn't jump between links so it is a little bit slower, but the normal navigation (arrow keys, page up, page down, etc.) works and the focus/caret/cursor follows (in contrast to a text editor for page up/down). And text can be selected and copied like in a text editor. The biggest drawback is that in practice it is necessary to switch in and out of caret mode. And there is no indication of which mode is currently active. Update 1: a work-around (proposed by several but is not really what I am looking for) can be used if 3 settings are changed (to make it practical). After these changes the first few letters of a link text can be typed and that link will selected so pressing Enter will open it. Using the work-around the screen will jump around if it is a long page as it does not restrict itself to the current visible page, but it is usable. First settings change: menu Tools/Options/Advanced/tab General/Accessibility/Search for text when I start typing Turn this option on. Second settings change: set option to only go to links; in address bar enter: about:config followed by Enter. Then: press "I'll be careful, I promise", find the line accessibility.typeaheadfind.linksonly, select it and change the value to True by either hitting Enter or Shift+F10/Toggle (accessibility.typeaheadfind.linksonly is on line 11 when I tried). Third settings change: turn off case-sensitivity. Set accessibility.typeaheadfind.casesensitive to 0 (same procedure as for accessibility.typeaheadfind.linksonly, see above. When Enter is pressed a dialog box will appear with the current value. Type 0 and press Enter). To use: type some part of the link. If there are several possibilities use Ctrl+G (or F3) to jump between them. Use Ctrl+Enter to open in a new tab. Platform: Firefox 3.0.6, Windows XP 64 bit SP2.

  Read the article

• Dell PowerEdge R720 - Corrupted RAID

  - by BT643

  Apologies in advance for the lengthy question. We have a Dell PowerEdge R720 server with: 2 x 136GB SAS drives in RAID 1 for the OS (Ubuntu Server 12.04) 6 x 3TB SATA drives in RAID 5 for data A few days ago we were getting errors when trying to access files on the large RAID 5 partition. We rebooted the server and got a message about the raid controller has found a foriegn config. We've had this before, and just needed to use Dell's RAID configuration utility to import foreign config on the RAID. Last time this worked, but this time, it started doing a disk check then we got this: FSCK has returned the following: "/dev/sdb1 inode 364738 has a bad extended attribute block 7 /dev/sdb1 unexpected inconsistency run fsck manually (i.e without -a or -p options) MOUNTALL fsck /ourdatapartition [1019] terminated with status 4 MOUNTALL filesystem has errors /ourdatapartition errors where found while checking the disk drive for /ourdatapartition Press F to fix errors, I to Ignore or M for Manual Recovery" We pressed F to try and fix the errors, but it eventually errored with: Inode 275841084, i_blocks is 167080, should be 0. Fix? yes Inode 275841141 has an invalid extend node (blk 2206761006, lblk 0) Clear? yes Inode 275841141, i_blocks is 227872, should be 0. Fix? yes Inode 275842303 has an invalid extend node (blk 2206760975, lblk 0) Clear? yes .... Error storing directory block information (inode=275906766, block=0, num=2699516178): Memory allocation failed /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** e2fsck: aborted /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** mountall: fsck /ourdatapartition [1286] terminated with status 9 mountall: Unrecoverable fsck error: /ourdatapartition We noticed one of the drive lights was not lit at all, and thought this may have failed and be the problem. We replaced the drive with a spare, and tried "F" to repair it again, but we keep just getting the same error as above. In the RAID configuration utility, all drives show as "online" and "optimal". We do have this data on another replicated server, so we're not worried about "recovering" anything, we just want to get the system back online asap. The server has 64 or 32GB memory, can't remember off the top of my head, but either way, with a 14TB RAID, I think it may still not be enough. Thanks EDIT - I checked the memory usage while fsck was running as suggested and after 2 or 3 minutes, it looked like this, using up nearly all of our servers memory: When it failed after 5 minutes or so with the error in my post, the memory immediately freed up again:

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• keyboard intermittently stops working, even after reinstalling windows 7; possibly a Chrome issue?

  - by neverskipbreakfast

  My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash a couple of the ctrl+alt+windows type keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu, but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) *Unplugging & reconnecting keyboard does NOT fix it. *Connecting a different keyboard does NOT fix it. That one won't work, either. *Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. *Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears, they keyboard won't work, and neither will the icon to pull up the on-screen keyboard. Otherwise my mouse can click around just fine. I can only log onto a non-password protected account. *Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. *Clearing my Chrome browsing data stopped the problem from recurring for a week or so. *I use Avira free antivirus software, and repeated scans turn up nothing fishy. *I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. The only thing I suspect is something in Google Chrome -- I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

  Read the article

• XCP Project Kronos syslog error: "irq ... : nobody cared" on Dom0 host

  - by Vlad Fedin

  One of our production clusters driven by XCP suddenly went uresponsive. After restart and some investigation we found such logs in dom0 machine syslog: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659040] irq 339: nobody cared (try booting with the "irqpoll" option) Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659058] Pid: 0, comm: swapper/3 Tainted: G C O 3.2.0-24-generic #37-Ubuntu Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659060] Call Trace: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659062] <IRQ> [<ffffffff810db37d>] __report_bad_irq+0x3d/0xe0 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659071] [<ffffffff810db605>] note_interrupt+0x135/0x190 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659074] [<ffffffff810d8e69>] handle_irq_event_percpu+0xa9/0x220 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659078] [<ffffffff8130ff3b>] ? radix_tree_lookup+0xb/0x10 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659081] [<ffffffff810d9031>] handle_irq_event+0x51/0x80 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659084] [<ffffffff810dc187>] handle_edge_irq+0x87/0x140 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659089] [<ffffffff813a8829>] __xen_evtchn_do_upcall+0x199/0x250 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659092] [<ffffffff813aa96f>] xen_evtchn_do_upcall+0x2f/0x50 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659096] [<ffffffff81666d3e>] xen_do_hypervisor_callback+0x1e/0x30 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659097] <EOI> [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659104] [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659107] [<ffffffff8100a1d0>] ? xen_safe_halt+0x10/0x20 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659110] [<fff IRQ 339 in cat /proc/interrupts: 339: ... xen-pirq-msi-x eth0 where eth0 is hardware NIC. While host machine seems to hang, guest machines continue to work, so our tiny internal monitoring on one of the virtual hosts logged something like that: [2012-10-26 20:31:51] [OK......] 200 OK : 113159149 ns [2012-10-26 20:32:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 47763284432 ns ... [2012-10-26 20:34:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 46894835070 ns [2012-10-26 20:34:57] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 16821741955 ns ... [2012-10-26 20:38:18] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 20103298289 ns [2012-10-26 20:38:37] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 17895754943 ns Host and guest OS: Ubuntu 12.04 LTS, 05:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection Subsystem: ASUSTeK Computer Inc. Device 8369 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fe500000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at e000 [size=32] Region 3: Memory at fe520000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: e1000e Kernel modules: e1000e Any hints how to debug this?

  Read the article

• How can the Private Bytes of a process be significantly less than its effect on the system commit charge?

  - by bacar

  On a 64-bit Windows Server 2003, I can see using taskmgr or process explorer that the total commit charge is around 3.5GB, yet when I sum the Private Bytes consumed by each process (by running pslist -m and adding all values under the Priv column) the total comes in at 1.6GB. I know which process seems to be causing this (sqlservr.exe) as when I kill the process, the commit charge drops dramatically. However the process in question is consuming only ~220MB of Private Bytes yet killing the process drops the commit charge by ~1.6GB. How is this possible? How can the commit charge be so significantly greater than Private Bytes, which should represent the amount of committed memory? If some other factor contributes to the commit charge, what is that factor and how can I view its impact in process explorer? Note: I claim that I understand the difference between reserved and committed memory already: my investigations above relate specifically to Private Bytes which includes only committed memory and excludes reserved memory. the Virtual Size of the process in this case is over 4GB, but this should be irrelevant - Virtual Size in procexp represents reserved, not committed memory, and should not contribute to the commit charge. I'm particularly interested in generalised answers to this question: I'm assuming that if sqlservr.exe can behave in this way, that any process potentially could. Further Investigations I notice that pointing Sysinternals VMMap at this process reports a committed "Private Data" of 1.6GB despite Procexp's reported a Private Bytes of 220MB. This is particularly strange given that the documentation for this field in the "Windows® Sysinternals Administrator's Reference" states that: Private Data memory is memory that is allocated by VirtualAlloc and that is not further handled by the Heap Manager or the .NET runtime, or assigned to the Stack category... VMMap’s definition of “Private Data” is more granular than that of Process Explorer’s “private bytes.” Procexp’s “private bytes” includes all private committed memory belonging to the process. i.e. that VMMap's committed "Private Data" should be smaller than procexp's "Private Bytes". Also, after reading the 'Process committed memory' section of Mark Russinovich's excellent Pushing the Limits of Windows: Virtual Memory, he highlights two cases which won't show up in Private Bytes: File mapping views with copy-on-write semantics (however, according to VMMap there is no significant space allocated to Mapped Files). pagefile-backed virtual memory (however, I tried testlimit with the -l flag as suggested, and no significant memory is consumed by pagefile-backed sections)

  Read the article

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• What info is really useful in my iptables log and how do I disable the useless bits?

  - by anthony01

  In my iptables rules files, I entered this at the end: -A INPUT -j LOG --log-level 4 --log-ip-options --log-prefix "iptables: " I DROP everything besides INPUT for SSH (port 22) I have a web server and when I try to connect to it through my browser, through a forbidden port number (on purpose), I get something like that in my iptables.log Sep 24 14:05:57 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=64 TOS=0x00 PREC=0x00 TTL=54 ID=59351 DF PROTO=TCP SPT=63776 DPT=1999 WINDOW=65535 RES=0x00 SYN URGP=0 Sep 24 14:06:01 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC= yy.yy.yy.yy DST=xx.xx.xx.xx LEN=48 TOS=0x00 PREC=0x00 TTL=54 ID=63377 DF PROTO=TCP SPT=63776 DPT=1999 WINDOW=65535 RES=0x00 SYN URGP=0 Sep 24 14:06:09 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=48 TOS=0x00 PREC=0x00 TTL=54 ID=55025 DF PROTO=TCP SPT=63776 DPT=1999 WINDOW=65535 RES=0x00 SYN URGP=0 Sep 24 14:06:25 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=48 TOS=0x00 PREC=0x00 TTL=54 ID=54521 DF PROTO=TCP SPT=63776 DPT=1999 WINDOW=65535 RES=0x00 SYN URGP=0 Sep 24 14:06:55 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=100 TOS=0x00 PREC=0x00 TTL=54 ID=35050 PROTO=TCP SPT=63088 DPT=22 WINDOW=33304 RES=0x00 ACK PSH URGP=0 Sep 24 14:06:55 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=52 TOS=0x00 PREC=0x00 TTL=54 ID=14076 PROTO=TCP SPT=63088 DPT=22 WINDOW=33264 RES=0x00 ACK URGP=0 Sep 24 14:06:55 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=52 TOS=0x00 PREC=0x00 TTL=54 ID=5277 PROTO=TCP SPT=63088 DPT=22 WINDOW=33248 RES=0x00 ACK URGP=0 Sep 24 14:06:56 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=100 TOS=0x00 PREC=0x00 TTL=54 ID=25501 PROTO=TCP SPT=63088 DPT=22 WINDOW=33304 RES=0x00 ACK PSH URGP=0 As you can see, I typed xx.xx.xx.xx:1999 in my browser, and it tried to connect until it timed out. 1) There are many similar lines for just one event. Do you think I need all of them? How would I avoid duplicates? 2) The last 4 lines are for my port 22. But since I allow port 22 INPUT for my web server, why are they here? 3) Do I need info like LEN,TOS,PREC and others? I'm trying to find a page that explains them one by one, by I can't find anything.

  Read the article

• Thinkpad speaker turns mute - Linux Codec issue?

  - by Curlew

  At some point a few days ago the speakers on my Lenovo Thinkpad T410 (Model number: 2537A11) suddenly stopped working randomly. This error happens every time I watch a video or listen to a music file. The sound just abruptly stops. At the moment, I can't produce a single sound no matter what I do. I am using Debian GNU/Linux on this laptop and there doesn't appear to be anything else wrong (the fan is working, no abnormal heat (staying around ~40°C), no other obvious errors or problems). Here is the output of a nice program someone pointed me to: martin@martin:~/Downloads$ sudo python run.py --monitor Using temporary directory: /dev/shm/hda-analyzer You may remove this directory when finished or if you like to download the most recent copy of hda-analyzer tool. Downloading file hda_analyzer.py Downloading file hda_guilib.py Downloading file hda_codec.py Downloading file hda_proc.py Downloading file hda_graph.py Downloading file hda_mixer.py Downloaded all files, executing hda_analyzer.py Watching 1 cards ====================================== Sound is working normally and then it stops and the following lines appear: Diff for codec 0/0 (0x14f15069): --- +++ @@ -164,17 +164,17 @@ Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Pincap 0x00000010: OUT Pin Default 0x901701f0: [Fixed] Speaker at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT - Power: setting=D0, actual=D0 + Power: setting=D3, actual=D3 Connection: 2 0x10* 0x11 Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE And now there is also an error in the dmesg output hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I changed the bdl_pos_adj to various numbers (-1, 0, 64, 1024) and either there is no change at all or dmesg reports that the adjustment is too big. I wonder if this bdl_pos_adj is the real reason for the error. Here is my hardware information provided by alsa-info.sh website. Okay, i did some serious testing and even installed Windows and now i officially conclude that this is a hard-ware related issue with my Laptop speakers. Reason: The error occurs in my installed Debian Linux, an Ubuntu Live distribution and Windows XP No error-message appears in all of the OS. The sound just keeps running and i can't hear a thing. I tested different setups, including OSS, ALSA and the pulseaudio server on top If i use my new usb-headphones i can hear sound all the time without any sudden silences. So obviously, although hard to believe, my laptop speakers are not okay (never heard of similar cases). I'll award the bounty to anyone who can point me to good tutorials or the procedure how to exchange my T410 speakers (i still have warranty. The laptop was bought in Germany, but now i am in Denmark). Or to someone who can explain me the output from hda-analyzer (big log above).

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files

  - by yegor

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• Is there any program (or code, any language) that will mute all of the microphones on my computer?

  - by Sean

  Is there any program (or code, any language) that will mute all of the microphones on my computer? If it is code, please make it as simple as possible, the only language I know is C# and I am still VERY new to it. I just want to setup some way to mute my microphones from a hotkey/shortcut, and if I can just find a program that can do, I will be set. As I said, I can also do a little bit if it is in C#, but the only code I have seen before for this, was miles long (atleast to me). My goal, is I just want a program that opens up, and toggles the mute on the microhpones (all of the system audio input) then closes. That is it, very simple. Thank you to anyone who trys to helps me! EDIT: Yes, I am using Windows. I am using Windows 7 32-bit. I already know that I can go into the volume mixer and do it that way, but I need to do this while running a full screen application, and it is a hassle to have to exit fullscreen, open the volume mixer, the click the mute icon, then go back into full screen and the the whole thing over again to unmute it. And I will be toggling back and forth quite often, so it just takes alot to do that so much.

  Read the article

• How can I make WSUS less invasive for our users?

  - by Cypher

  We have WSUS pushing updates out to our user's workstations, and things are going relatively well with one annoying caveat: there seems to be an issue with a pop-up being displayed in front of some users informing them that their machine will be rebooted in 15 minutes, and they have nothing to say about it: This may be because they did not log out the prior night. Nevertheless, this is a bit too much and is very counter-productive for our users. Here is a bit about our environment: Our users are running Windows XP Pro and are part of an Active Directory Domain. WSUS is being applied via Group Policy. Here is a snapshot of the GPO that is enforcing the WSUS rules: Here is how I want WSUS to work (ideally - I'll take whatever can get me close): I want updates to automatically download and install every night. If a user is not logged in, I would like the machine to reboot. If a user is logged in, I would like their machine not to reboot, but instead wait until the next "installation period" where it can perform any other needed installations and reboot then (provided the a user account is not still logged in). If a user is to be prompted for reboot, it should only happen once per day (if possible), but every time they are prompted, they must have a way to postpone the reboot. I do not want users to be forced to restart their computer whenever the computer thinks it should happen (unless it's after an update installation and there are no logged in users). That doesn't seem productive to force a system restart in the midst of a person's workday. Is there something that I can do with the GPO that would help make WSUS less intrusive? Even if it gave the user an option to Restart Later - that would be better than what is happening now.

  Read the article

• Network connection keeps dropping - bad hardware?

  - by Bill Sambrone

  Hello all, I've into a bit of a wall with a client of mine. In an office of 20 people, he is the only one who experiences broken connections to his mapped network drives. I have everyone set up with about 6 mapped drives, all pointing to the same server (no DFS), and everyone else can access them lightning fast. The environment consists of a mix of Windows 7 and XP machines, all 32-bit. The server holding the data everyone is mapping to is running on Server 2008 R2, and is a domain controller. We recently swapped out their old 10/100 switch for a shiny new Dell PowerConnect gigabit switch. We have also replaced an old dying Sonicwall with a shiny new one. Everything is running on an ESX host except for the DC, where everyone is getting data from. In my client's office, we have done the following: Swapped out his computer (Win7 and XP box) Swapped out the desktop switch in his office Removed the desktop switch in his office Changed out the network cable going to the wall Ran 'net config server /autodisconnect:-1' on the server Disabled remote differential compression on his current Win7 box When we swapped out his network cable, everything seemed fine for about 4 days. Normally I would get a phone call a couple times per day letting me know that Outlook has crashed (there is a 9GB PST living on the server he is always connected to), or that his software he is running from his L drive has crashed. I almost thought I had this solved, but after we rebooted the DC the other night he all of a sudden couldn't stay connected to his mapped network drives for more than 10 minutes. When I ran 'net use' from the command prompt, it listed all the network drives where were randomly in a state of 'OK', 'Disconnected', or 'Reconnecting'. What else should I try? Maybe there is bad wiring in the wall, patch panel, or a bad port in the new switch I have in the server room?

  Read the article

• Second network card configuration not working.

  - by Sebas

  I have 4 servers running Centos 5. All of them have two ethernet network cards. I have configured 192.168.1.x IP addresses on their eth0 card. They are all connected to the same switch using their eth0 card and they are all working. I have configured 10.72.11.x IP addresses on their eth1 card.They are all connected to the same switch - a different one from the switch used with eth0 card - using their eth1 card and they are NOT all working. Their configuration files is like: DEVICE=eth1 BOOTPROTO=static IPADDR=10.72.11.236 BROADCAST=10.72.11.191 NETMASK=255.255.255.192 NETWORK=10.72.11.128 HWADDR=84:2B:2B:55:4B:98 IPV6INIT=yes IPV6_AUTOCONF=yes ONBOOT=yes The interfase is starting and configured as I need. [root@sql1 network-scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:97 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::862b:2bff:fe55:4b97/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2981 errors:0 dropped:0 overruns:0 frame:0 TX packets:319 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:386809 (377.7 KiB) TX bytes:66134 (64.5 KiB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:98 inet addr:10.72.11.236 Bcast:10.72.11.191 Mask:255.255.255.192 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:48 Memory:dc000000-dc012800 I also added a route-eth1 file that looks like: 10.0.0.0/8 via 10.72.11.254 Routing looks fine to me: [root@sql1 network-scripts]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.72.11.192 0.0.0.0 255.255.255.192 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.72.11.254 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 But I cannot ping one server from the other. [root@sql1 network-scripts]# ping 10.72.11.235 PING 10.72.11.235 (10.72.11.235) 56(84) bytes of data. From 10.72.11.236 icmp_seq=1 Destination Host Unreachable From 10.72.11.236 icmp_seq=2 Destination Host Unreachable From 10.72.11.236 icmp_seq=3 Destination Host Unreachable From 10.72.11.236 icmp_seq=4 Destination Host Unreachable From 10.72.11.236 icmp_seq=5 Destination Host Unreachable From 10.72.11.236 icmp_seq=6 Destination Host Unreachable ^C --- 10.72.11.235 ping statistics --- 7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6033ms , pipe 3 What am I doing wrong?

  Read the article

• Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

  - by Shasteriskt

  I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

  Read the article

• FreeNAS pool configuration - RAID1 + other drives

  - by trnelson

  Simple questions, really. I found this answer with a similar setup, but not sure it answers my question. If it does, I'm curious why since the answer seems a bit unsure: ZFS Hard Drive Configuration in FreeNAS I'm building a server which will be used primarily for backup, plus some media streaming, possibly with Plex. I seem to understand most everything I need, but I'm still a bit confused on how pools work, and how to configure them for my scenario. I will have 2x 2TB WD Red drives, which I plan on using in a mirrored set up (RAID1). This would be for backup, and I'd also like to do offsite backup to my CrashPlan account from this array. I also have a few other drives: 1.5TB, 320GB, 250GB. I'm not sure exactly what to do with them yet, but looking for options. FreeNAS OS will be running from a 16GB USB Flash drive. Would it be wise to use the 1.5TB as a backup-backup, essentially as a mirror or perhaps for snapshots of the 2TB RAID1? I'm still learning about snapshots. Should the 2TB mirrored drives be in their own pool? Should the other drives be set up in their own pools as well, or should they be JBOD in a single pool? They may or may not get much use since the 2TB array is plenty for me. Does a dataset basically mimic the idea of a partition or a network share? In other words, I would map \SERVER\Share to X: on my laptop? Let's say I wanted to use the 250GB drive as an encrypted drive to store all of my cat pictures. Would it have to be in its own pool? If I use jails apps, should they go in the backup RAID1, or in another place? Thank you!

  Read the article

• Any way to recover ext4 filesystems from a deleted LVM logical volume?

  - by Vegar Nilsen

  The other day I had a proper brain fart moment while expanding a disk on a Linux guest under Vmware. I stretched the Vmware disk file to the desired size and then I did what I usually do on Linux guests without LVM: I deleted the LVM partition and recreated it, starting in the same spot as the old one, but extended to the new size of the disk. (Which will be followed by fsck and resize2fs.) And then I realized that LVM doesn't behave the same way as ext2/3/4 on raw partitions... After restoring the Linux guest from the most recent backup (taken only five hours earlier, luckily) I'm now curious on how I could have recovered from the following scenario. It's after all virtually guaranteed that I'll be a dumb ass in the future as well. Virtual Linux guest with one disk, partitioned into one /boot (primary) partition (/dev/sda1) of 256MB, and the rest in a logical, extended partition (/dev/sda5). /dev/sda5 is then setup as a physical volume with pvcreate, and one volume group (vgroup00) created on top of it with the usual vgcreate command. vgroup00 is then split into two logical volumes root and swap, which are used for / and swap, logically. / is an ext4 file system. Since I had backups of the broken guest I was able to recreate the volume group with vgcfgrestore from the backup LVM setup found under /etc/lvm/backup, with the same UUID for the physical volume and all that. After running this I had two logical volumes with the same size as earlier, with 4GB free space where I had stretched the disk. However, when I tried to run "fsck /dev/mapper/vgroup00-root" it complained about a broken superblock. I tried to locate backup superblocks by running "mke2fs -n /dev/mapper/vgroup00-root" but none of those worked either. Then I tried to run TestDisk but when I asked it to find superblocks it only gave an error about not being able to open the file system due to a broken file system. So, with the default allocation policy for LVM2 in Ubuntu Server 10.04 64-bit, is it possible that the logical volumes are allocated from the end of the volume group? That would definitely explain why the restored logical volumes didn't contain the expected data. Could I have recovered by recreating /dev/sda5 with exactly the same size and disk position as earlier? Are there any other tools I could have used to find and recover the file system? (And clearly, the question is not whether or not I should have done this in a different way from the start, I know that. This is a question about what to do when shit has already hit the fan.)

  Read the article

• Intermittently uncommunicative subnets

  - by mhd

  Last week proved me a veritable Cassandra: I've always said that it's a bad idea to have only one firewall/router, without a backup or failover. And thus our Cisco PIX went haywire, refusing to route properly. And of course, the only one available here on short notice is me, and while I'm quite grounded in Linux, I'm really a developer not a sysadmin (the fact that this hit me on sysadmin appreciation day is a bit ironic). Anyway, this weekend I tried to hack up a temporary solution: I used an old server with enough NICs (two built-in, four on a card) to serve as a gateway and firewall. Due to some problems with the raid controller, I got only two router distros running, and between Untangle and Ebox I decided for the latter. Now everything is quite okay. I've got all the different subnets we've got here (all with separate switches) talking to each other and even to the internet (Cisco 2800 router, T1 lines). But from time to time (20-60 minute intervals), I get a total routing failure. Our main, office subnet can't talk to our server subnet and can't connect to the internet. This is not the end of a gradual slowdown, either everything's working perfectly or I get a total lack of communication for about two minutes each time. Now I'm a bit at wits end what to check. At least with the default EBox setup, nothing in /var/log shows anything weird and it doesn't exactly have lots of built-in monitoring tools. So I'm hoping someone here could give me some pointers about what to look out for. I did change the ethernet cable from the office switch to the firewall, with no results. I might change switches, although within the switch it seems to work ok enough. Edit: I'm not sure whether this is the sole cause of the problem, but after I noticed a few DHCP entries just before the last drop of connectivity, I tried to reproduce that. And alas, whenever I renew a DHCP connection, I can't access other subnets anymore. Running ISC DHCPD 3.0.6.

  Read the article

• Failed to start up after upgrading software in ubuntu 10.10

  - by Landy

  I've been running Ubuntu 10.10 in a physical x86-64 machine. Today Update Manager reminded me that there are some updates to install and I confirmed the action. I should had read the update list but I didn't. I can only remember there is an update about cups. After the upgrading, Update Manager requires a restart and I confirmed too. But after the restart, the computer can't start up. There are errors in the console. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. [xxx]usb 1-8: new high speed USB device using ehci_hcd and address 3 [xxx]usb 2-1: new full speed USB device using ohci_hcd and address 2 [xxx]hub 2-1:1.0: USB hub found [xxx]hub 2-1:1.0: 4 ports detected [xxx]usb 2-1.1: new low speed USB device using ohci_hcd and address 3 Gave up waiting for root device. Common probles: - Boot args (cat /proc/cmdline) - Check rootdelay=(did the system wait long enough) - Check root= (did the system wait for the right device?) - Missing modules (cat /proc/modules; ls /dev) FATAL: Could not load /lib/modules/2.6.35-22-generic/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.35-22-generic/modules.dep: No such file or directory ALERT! /dev/sda1 does not exist. Dropping to a shell! BusyBox v1.15.3 (Ubuntu 1:1.15.3-1ubuntu5) built-in shell(ash) Enter 'help' for a list of built-in commands. (initramfs)[cursor is here] At the moment, I can't input anything in the console. The keyboard doesn't work at all. What's wrong? How can I check boot args or "root=" as suggested? How can I fix this issue? Thanks. =============== PS1: the /dev/sda1 is type ext4 (rw,nosuid,nodev) PS2: the /dev/sda1 can be mounted and accessed successfully under SUSE 11 SP1 x64.

  Read the article

• Doing arithmetic and passing it to the next command

  - by neurolysis

  I know how to do this in /bin/sh, but I'm struggling a bit in Windows. I know you can do arithmetic on 32-bit signed integers with SET /a 2+2 4 But how do I pass this to the next command? For example, the process I want to perform is as follows. Consumer editions of Windows have no native automated sleep function (I believe?) -- the best way to perform a sleep is to use PING in association with the -n switch to get that many seconds, minus one, of sleep. The following command is effective for a silent sleep: PING localhost -n 3 > NUL But I want to alias this into a sleep command. I'd like to have it elegant so that you enter the actual number of seconds you want to sleep after the command, right now I can do DOSKEY SLEEP=PING 127.0.0.1 -n $1 > NUL Which works, but it's always 1 second less than your input, so if you wanted to sleep for one second you would have to use the command SLEEP 2. That's not exactly ideal. Is there some way for me to pass the arithmetic of $1+1 and pass it on to the next command in Windows? I assume there is some way of using STDOUT...

  Read the article

< Previous Page | 385 386 387 388 389 390 391 392 393 394 395 396  | Next Page >