Search Results

Search found 12605 results on 505 pages for 'my settings'.

Page 390/505 | < Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >

• Can I have a single solid state drive and a RAID array on the same machine?

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Testlink stop working when configuring it to use LDAP

  - by YuriAlbuquerque

  I have a TestLink webservice running on a server, and OpenLDAP running on other server. There are no firewall problems between them (I managed to configure Redmine, on the same server as TestLink, to use LDAP authentication). But whenever I place the configuration for LDAP in TestLink, TestLink stops working. I have no clue on what is happening. This is where I define LDAP's settings on custom_config.inc.php: $tlCfg->authentication['method'] = 'LDAP'; $tlCfg->authentication['ldap_server'] = 'serverip'; $tlCfg->authentication['ldap_port'] = '389'; $tlCfg->authentication['ldap_version'] = '2'; $tlCfg->authentication['ldap_root_dn'] = 'dc=mycompany,dc=com,dc=br'; $tlCfg->ldap_organization'] = ''; $tlCfg->authentication['ldap_uid_field'] = 'uid'; $tlCfg->authentication['ldap_bind_dn'] = 'myuser'; //Not actual login name and password, for obvious reasons $tlCfg->authentication['ldap_bind_passwd'] = 'mypassword'; $tlCfg->authentication['ldap_tls'] = false; $tlCfg->user_self_signup = true; I'm certain that OpenLDAP is 2.X. My TestLink version is 1.9.3 What could I be doing wrong?

  Read the article

• Missing Home Folder XP Clients 2008R2 Domain

  - by minamhere

  We just completed a migration from Server 2003 to Server 2008R2. Everything seems to have gone well except that many of our desktops have stopped mapping the Home Folder as set in Active Directory. Other mappings that are defined on individual clients are mapping just fine, these mappings are all on the same file server as the failing Home Folders. Half of the users are on 1 file server and half are on another. Users from both servers are having this problem. I have enabled the Group Policy setting to "Wait for network before logging in". I enabled the policy to "Run Logon Scripts synchronously". There are no errors on the Domain Controller or either File Server. When I enabled Group Policy Preferences as an attempted workaround, I get this error: The user 'V:' preference item in the '<Policy Name>' Group Policy object did not apply because it failed with error code '0x800708ca This network connection does not exist.' This error was suppressed. This seems to indicate that the network connection is not ready by the time Group Policy is processed. But isn't this the point of the "Wait before logging in" and "Run Logon scripts synchronously" settings? Some other background facts: The new Server 2008R2 installation is a Virtual Machine. It is on a new Subnet in a different building from the old server. DNS and DHCP were also migrated from the old DC to this new DC. These Home Folders were all working properly before the migration. Are there new security restrictions/policies in Server 2008R2 that might be causing this? Is there a way to check whether I have an underlying network connectivity issue? Maybe moving the server to the new building is causing a delay/timeout? Any thoughts or ideas on what could be causing this or how I can resolve this? Thanks.

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• cups log kills ubuntu 12.04 and sudoer permissions changed

  - by peterretief

  I am using Ubuntu 12.04 as a desktop and recently had a weird crash with the log file for cups filling up the entire drive and not letting me back in, also what changed was /var/lib/sudo had changed from root to peter (me) I didn't make this change - I checked the history! I set the sudoers back to root and capped the max size for cups log Anyone had a similar experience? It feels like someone is messing around with my settings Is there any way to trace how the error occurred? Logs auth.log Jan 1 02:04:13 peter-desktop lightdm: pam_unix(lightdm:session): session opened for user lightdm by (uid=0) Jan 1 02:04:13 peter-desktop lightdm: pam_ck_connector(lightdm:session): nox11 mode, ignoring PAM_TTY :0 Jan 1 02:06:53 peter-desktop lightdm: pam_unix(lightdm:session): session opened for user lightdm by (uid=0) Jan 1 02:06:53 peter-desktop lightdm: pam_ck_connector(lightdm:session): nox11 mode, ignoring PAM_TTY :0 syslog Jan 1 02:04:13 peter-desktop rsyslogd: [origin software="rsyslogd" swVersion="5.8.6" x-pid="903" x-info="http://www.rsyslog.com"] start Jan 1 02:04:13 peter-desktop rsyslogd: rsyslogd's groupid changed to 103 Jan 1 02:04:13 peter-desktop rsyslogd: rsyslogd's userid changed to 101 Jan 1 02:04:13 peter-desktop rsyslogd-2039: Could not open output pipe '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] Jan 1 02:04:13 peter-desktop bluetoothd[898]: Failed to init gatt_example plugin Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] Initializing cgroup subsys cpuset Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] Initializing cgroup subsys cpu Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] Linux version 3.2.0-25-generic-pae (buildd@palmer) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #40-Ubuntu SMP Wed May 23 22:11:24 UTC 2012 (Ubuntu 3.2.0-25.40-generic-pae 3.2.18) Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] KERNEL supported cpus: Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] Intel GenuineIntel Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] AMD AuthenticAMD Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] NSC Geode by NSC

  Read the article

• Change the Default Date setting in Word 2010

  - by Chris

  I am using Word 2010 and Windows 7. You know how when you start typing a date in Word it will automatically suggest what it thinks you want? Like if I start typing “6/29”, a little grey bubble will display “6/29/13 (Press ENTER to Insert)”. How do I get it so the bubble will display the year in a 4 digit format, such as "6/29/2013 (Press Enter to Insert)"? The below picture is how it looks when typing a date into Word. I have already gone to the Date & Time option under the Insert menu and the date format that I want is already selected. I think this is only for using quickparts anyway, so the date automatically updates when you open a document. The Region and Language settings under the Control Panel are correct as well. I thought at one point I found it somewhere under options, but I am sure I looked through everything many times and I can’t find it. I posted this exact question at the Microsoft website and someone replied: Go to the Windows Control Panel and click on Clock, Language and Region and then on Change the date, time, or number format and then modify the Short date format so that it is what you want to be used. So please don't suggest this again, because in my question I did say that I already tried this and it doesn't work, at least not for Word, in this situation. Thanks.

  Read the article

• Apache doesn't immediately notice a change in the document root

  - by Tom

  We use capistrano for website deployments and our Apache document root is a symlink to a particular code release. The deployment procedure switches the symlink from the old release to the new release as the final step of the deployment. We are migrating our webservers from real servers running RHEL 5.6 to Amazon EC2 virtual machines running Ubuntu 11.10 and the new servers are suffering from a problem where Apache doesn't immediately notice the change to it's document root when the symlink is switched. It can take a second or so (and I think I've even seen it take a couple of minutes). It's kind of like Apache has cached the physical path of the symlink for some time. Does anyone know some Apache settings I could look at to get it to "scan" for changes to it's served files quicker. Thoughts: I read that the disks on virtual machines are much slower (since they are network attached storage). Perhaps the filesystem cache somehow works differently too? If so, is there anything that can be done? The website runs PHP code. Perhaps there is some PHP config differences between RHEL and Ubuntu? I checked realpath_cache_ttl but both servers have it commented out: e.g. ; Duration of time, in seconds for which to cache realpath information for a given ; file or directory. For systems with rarely changing files, consider increasing this ; value. ; http://www.php.net/manual/en/ini.core.php#ini.realpath-cache-ttl ;realpath_cache_ttl = 120 We do use the APC opcode cache but don't think it's the issue due to experimentation. The PHP code is in different file paths for each deployment and we ensure stat=1. Here is a similar question that is very interesting: 294107 - but doesn't provide an answer for me. One solution would be to reload Apache everytime we modify the document root symlink. I'll do this if we can't find another solution.

  Read the article

• How to install a private user script in Chrome 21+?

  - by Mathias Bynens

  In Chrome 20 and older versions, you could simply open any .user.js file in Chrome and it would prompt you to install the user script. However, in Chrome 21 and up, it downloads the file instead, and displays a warning at the top saying “Extensions, apps, and user scripts can only be added from the Chrome Web Store”. The “Learn More” link points to http://support.google.com/chrome_webstore/bin/answer.py?hl=en&answer=2664769, but that page doesn’t say anything about user scripts, only about extensions in .crx format, apps, and themes. This part sounded interesting: Enterprise Administrators: You can specify URLs that are allowed to install extensions, apps, and themes directly through the ExtensionInstallSources policy. So, I ran the following commands, then restarted Chrome and Chrome Canary: defaults write com.google.Chrome ExtensionInstallSources -array "https://gist.github.com/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://gist.github.com/*" Sadly, these settings only seem to affect extensions, apps, and themes (as it says in the text), not user scripts. (I’ve filed a bug asking to make this setting affect user scripts as well.) Any ideas on how to install a private user script (that I don’t want to add to the Chrome Web Store) in Chrome 21+? Update: The problem was that gist.github.com’s raw URLs redirect to a different domain. So, use these commands instead: # Allow installing user scripts via GitHub or Userscripts.org defaults write com.google.Chrome ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" This works!

  Read the article

• 4.00gb (3.25gb usable) in Windows 7 x64

  - by dotnetdev

  Hi, I have setup Windows 7 Ultimate x64 on my PC. I have 4gb RAM and my BIOS states the correct amount (4096mb), but I cannot Windows (System Manager) says I have 4.00gb (3.25gb usable). This seems to be a popular issue, and I have looked for an integrated video card (integrated with my chipset) to disable but haven't found anything. What else can be preventing me from seeing all 4gb? When I had Vista 32bit, it would say 3.25gb RAM not 4.00gb (3.25gb usable). I have an x64 CPU and when I brought my RAM, I used a compatibility tool from Crucial (the memory vendor) to test how much memory my PC can support and 4gb was the answer (this was a windows app I think). Chipset is Intel(R) G33/G31/P35/P31 Express Chipset PCI Express In the bios, I looked for an onboard video card (integrated) and there was no such thing, but a couple of other onboard devices. There are also no "Resource Mappings" settings. FURHTER DETAILS: Chipset North Bridge: Intel Bearlake G33 South Bridge: Intel 82801IR ICH9R Maximum Memory Amount 8 GB Graphics Controller Type Intel GMA 3100 (Enabled) I guess the first thing is, how do I disable the graphics controller? EDIT: This thread (http://forums.legitreviews.com/about23417.html) indicates the issue is with memory mapped devices, but someone on this thread says that does not apply to x64. The rest of the comments points to a mobo issue for the guy who started that thread. Thanks

  Read the article

• Poor gaming performance with hyper-v installed in windows 8

  - by SnowCrash

  I am getting very poor gaming performance on my Windows 8 host OS with Hyper-V installed but no guest machines running. For example World of Tanks reports 60-70 FPS without Hyper-V installed and 4-14 FPS with it installed. A similar, dramatic, hit is observed in several other games so the issue is not WoT specific. To make the point clear, I am not trying to run games in a virtual machine. I don't even have a VM running while observing this effect. I simply have the Hyper-V feature installed. My system specs: AMD Phenom II 965 (3.4 GHz) AMD Radeon 6950 2GB (XFX Double D HD-695X-CDFC) 16GB DDR3 1333 AMD 790GX chipset Mainboard (Gigabyte GA-MA790GPT-UD3H) I have tried every AMD driver from 12.8 to the current 12.11beta8, virtualization is enabled in the BIOS settings, the onboard 3300HD video device is disabled in BIOS and I have read the MSDN blog entry here regarding a similar issue in Server 2008 that was resolved in 2008 R2 (and hopefully not regressed in Win 8). I'd like to be able to use Hyper-V for development and testing at home (I am a sysadmin/software developer professionally). If, however, I can't also use my home system for entertainment I'll have to scrap those plans.

  Read the article

• Windows 7 Users unable to add Windows 2003 server printers

  - by TravBrack

  Hi there I just rolled out a few Windows 7 x64 machines and ran into this issue where non-admin users are unable to add printers hosted on a windows 2003 server. It works fine on a 2008 server. The issue appears to be with the point and print system. A user will attempt to add the printer, a prompt will come up requiring the user to elevate privileges in order to install a driver, and will fail citing 'access denied'. I found the group policy setting Point and Print Restrictions: When the policy setting is disabled: -Windows Vista computers will not show a warning or an elevated command prompt when users create a printer connection to any server using Point and Print. So I disabled it, verified that the policy was being picked up using rsop, but it still does the same thing. I've also tried the following: Recreating the printers using newer drivers Adding the printer using 32 bit drivers on the 2003 machine, then adding the 64 bit drivers on a Windows 7 machine Adding the printer from a windows 7 machine using print management None of these things work. The security settings are no different than the working printers. Help?

  Read the article

• Why Is ModSecurity Unable to Access the Data Directory?

  - by tommytwoeyes

  Update I think we've solved this; the problem appears to have been a result of the /modsec_storage directory having an incorrect value for its SELinux context type. However, we're still not sure, because although after I changed the SELinux context type value, Apache was able to create files in that directory for the global and ip collections (global.dir/global.pag and ip.dir/ip.pag), the new files still have zero bytes. I'm new to ModSecurity and am not sure if the files are empty because something is wrong with the configuration or if ModSecurity has simply determined it doesn't need to store IP addresses persistently after each transaction ends. Anyone able to offer guidance here? I've recently installed ModSecurity (v2.5.12 / CRS v2.0.8) on our production server, and everything works great, except for these errors that it keeps writing to the Apache error log: Failed to access DBM file "/modsec_storage/global": Permission denied [hostname "www.internationalstudent.com"] [uri "/includes/soc_bookmarks/images/delicious.png"] [unique_id "LZ6jc38AAAEAAFO6408AAABO"] Failed to access DBM file "/modsec_storage/ip": Permission denied [hostname "www.internationalstudent.com"] [uri "/includes/soc_bookmarks/images/delicious.png"] [unique_id "LZ6jc38AAAEAAFO6408AAABO"] After following the instructions for file permission settings in the ModSecurity handbook by Ivan Ristic, with no success, I created a /modsec_storage directory, set the owner & group to apache, and set the permissions for the directory recursively to 777. However, ModSecurity is still reporting the same permission errors, so I am stumped. Can anyone tell me how to fix this?

  Read the article

• Launching Installer Via Powershell and WinRM and Nothing Happens

  - by Nick DeMayo

  I'm currently working on a Powershell script to run some Microsoft Hotfix installers remotely on several Windows Server 2008 R2 servers that I manage. Basically, the script copies all the appropriate files up to the server, and then runs the installer via Invoke-Command, like so: function InstallCU { Write-Host "Installing June 2013 CU..." Invoke-Command -ComputerName $ServerName -ScriptBlock { Start-Process "c:\aaa\prjcusp2\ubersrvprj2010-kb2817530-fullfile-x64-glb.exe" -ArgumentList "/passive" } } If I run the "Start-Process" command locally on the server, the installer runs properly. However, when trying to run it remotely, nothing happens (actually, I can see the installer start up in Task Manager, but it closes a couple seconds later and doesn't run). I've attempted giving the Invoke-Command -Credentials, I've turned off UAC on the server, and I've ensured that my WinRM settings (running 'winrm quickconfig' and setting TrustedHosts to *) are correct. I've also tried having the Invoke-Command script run a local Powershell script to run the installer and changing the Argument from '/passive' to 'quiet' (in case it can't remotely launch something that has a UI), but again, no dice. Is there anything else I can try, or am I just not going to be able to do this?

  Read the article

• Is there a reason to use internal DNS over 8.8.8.8 ?

  - by skylarking

  I've inherited a LAN where there is really no name resolution being done for local resources... i.e. all users enter IP addresses manually to access printers and network shares. There are no LDAP servers or domains either....workstations simply connect to the network without authentication. DHCP is handled via a core switch... And DNS settings are also handed out by this same core switch. Currently, the DNS assignments are as such, and in this order: 10.1.1.50 / old Pentium III Windows 2003 box running DNS service- 128 MB RAM 169.200.x.x / ISP 4.2.2.2. / the well known public one There a couple thousand clients on the LAN....and most of the activity is web browsing ( this is an educational setting ). First of all, the server seems woefully underpowered for this task...yet there is virtually no slowness when web surfing by clients.... How much horsepower should a heavily used DNS server have ? I have also heard using 4.2.2.2 is a bad idea .... since it has been so overused... Finally, wouldn't it make sense to have a robust external DNS server listed first? ( Google's 8.8.8.8 would seem to be a logical candidate )

  Read the article

• Wireless USB keyboard and mouse can wake system, but then receiver is inactive

  - by BlueMonkMN

  I have a Microsoft brand USB device that acts as a receiver for a wireless Microsoft Keyboard and a wireless Mouse. When it's operating normally, there are LEDs on the device indicating Caps Lock, Num Lock and Function Lock, of which the latter 2 are usually lit. It is plugged into a Dell Isnpiron 531 with Windows 7 32-bit running on an AMD Athlon 64 X2 Dual Core processor 5000+. When the computer goes to sleep (the power indicator on the main box is flashing), I can wake it by moving the mouse. So far all is good. However, something changed in, I think, the past couple weeks (I suspect due to a Microsoft driver update problem). Before the change, after waking the computer, everything would operate normally as far as I could tell, but now after waking the computer, the receiver has no lights on, and the keyboard and mouse are completely unresponsive (which is odd, considering the mouse woke up the computer). There is a button on the receiver that's supposed to reset the wireless connection and flash the lights while it does so, but it has no effect in this state. It's like the receiver doesn't have power (but how would the system know I moved the mouse, unless the power was on until it woke up?). I have checked the BIOS/CMOS settings or whatever you call them, and did not see anything related to USB in the power management section. I have checked Windows 7 device manager and ensured that all the USB Root Hub devices have the setting unchecked for allowing the USB power to be turned off. Like I said, this was working before, and the only thing I can think of that's changed is applying Windows Updates.

  Read the article

• ssh keys rejected each day

  - by EddyR

  I've had OpenSSH server running on my debian server for a couple weeks and all of a sudden now when I go to login the next day it rejects my ssh key and I have to manually add a new one each time. Not only that but I have the "tunneling with clear-text passwords" option enabled and the non-root (login with root is disabled) account for that is rejected too. I'm at a loss why this is happening and I can't find any ssh options that would explain it. --update-- I just changed debug level to DEBUG. But before that I'm seeing a lot of the following in auth.log Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session opened for user root by (uid=0) Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session closed for user root ... Feb 1 04:36:26 greenpages sshd[7217]: reverse mapping checking getaddrinfo for nat-pool-xx-xx-xx-xx.myinternet.net [xx.xx.xx.xx] failed - POSSIBLE BREAK-IN ATTEMPT! ... Feb 1 04:37:31 greenpages sshd[7223]: Did not receive identification string from xx.xx.xx.xx ... My sshd_conf file settings are: # Package generated configuration file # See the sshd(8) manpage for details # What ports, IPs and protocols we listen for Port xxx # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel DEBUG # Authentication: LoginGraceTime 120 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding no X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM no ClientAliveInterval 60 AllowUsers myuser

  Read the article

• How to Change the Kerberos Default Ticket Lifetime

  - by user40497

  Our KDC servers are running either Ubuntu Dapper (2.6.15-28) or Hardy (2.6.24-19). The Kerberos software is the MIT implementation of Kerberos 5. By default, a Kerberos ticket lasts for 10 hours. However, we'd like to increase it a bit (e.g. 14 hours) to suit our needs better. I had done the following but the ticket lifetime still stays at 10 hours: 1) On all the KDC servers, set the following parameter under [realms] in /etc/krb5kdc/kdc.conf and restarted the KDC daemon: max_life = 14h 0m 0s 2) Via "kadmin", changed the "maxlife" for a test principal via "modprinc -maxlife 14hours ". "getprinc " shows that the maximum ticket life is indeed 14 hours: Maximum ticket life: 0 days 14:00:00 3) On a Kerberos client machine, set the following parameters under [libdefaults], [realms], [domain_realm], and [login] in /etc/krb5.conf (everywhere basically since nothing I tried had worked): ticket_lifetime = 13hrs default_lifetime = 13hrs With the above settings, I suppose that the ticket lifetime would be capped at 13 hours. When I do "k5start -l 14h -t ", I see that the end time for the "renew until" line is now 14 hours from the starting time: Valid starting Expires Service principal 04/13/10 16:42:05 04/14/10 02:42:05 krbtgt/@ renew until 04/14/10 06:42:03 "-l 13h" would make the end time in the "renew until" line 13 hours after the starting time. However, the ticket still expires in 10 hours (04/13 16:42:05 - 014/14 02:42:05). Am I not changing the right configuration file(s)/parameter(s), not specifying the right option when obtaining a Kerberos ticket, or something else? Any feedback is greatly appreciated! Thank you!

  Read the article

• Samba server NETBIOS name not resolving, WINS support not working

  - by Eric

  When I try to connect to my CentOS 6.2 x86_64 server's samba shares using address \\REPO (NETBIOS name of REPO), it times out and shows an error; if I do so directly via IP, it works fine. Furthermore, my server does not work correctly as a WINS server despite my samba settings being correct for it (see below for details). If I stop the iptables service, things work properly. I'm using this page as a reference for which ports to use: http://www.samba.org/samba/docs/server_security.html Specifically: UDP/137 - used by nmbd UDP/138 - used by nmbd TCP/139 - used by smbd TCP/445 - used by smbd I really really really want to keep the secure iptables design I have below but just fix this particular problem. SMB.CONF [global] netbios name = REPO workgroup = AWESOME security = user encrypt passwords = yes # Use the native linux password database #passdb backend = tdbsam # Be a WINS server wins support = yes # Make this server a master browser local master = yes preferred master = yes os level = 65 # Disable print support load printers = no printing = bsd printcap name = /dev/null disable spoolss = yes # Restrict who can access the shares hosts allow = 127.0.0. 10.1.1. [public] path = /mnt/repo/public create mode = 0640 directory mode = 0750 writable = yes valid users = mangs repoman IPTABLES CONFIGURE SCRIPT # Remove all existing rules iptables -F # Set default chain policies iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP # Allow incoming SSH iptables -A INPUT -i eth0 -p tcp --dport 22222 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22222 -m state --state ESTABLISHED -j ACCEPT # Allow incoming HTTP #iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT #iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT # Allow incoming Samba iptables -A INPUT -i eth0 -p udp --dport 137 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 137 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p udp --dport 138 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 138 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 139 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 139 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 445 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 445 -m state --state ESTABLISHED -j ACCEPT # Make these rules permanent service iptables save service iptables restart**strong text**

  Read the article

• IE9 will not navigate to some websites but Google Chrome can

  - by Storchburp

  Was recommended by a friend to ask for help here. I am using Internet Explorer 9. As of two days ago I was suddenly unable to navigate to any part of the following websites: www.computerandvideogames.com www.deviantart.com www.cnet.com However I can still access all of them normally through Google Chrome. I am on a college network but these sites are also accessible through fixed terminals provided by the school and are definitely not blocked. I do not know of any other sites similarly affected. There is no popup, no error message, no diversion to a site telling me I can't access / am blocked etc. I can be on www.google.com and attempt to access these sites through the URL or google search, and my cursor will just show the little moving blue wheel next to the arrow for a couple of seconds, and the page displayed on my browser will not change; ie. not navigating at all. Running antivirus software, changing proxy settings in IE, clearing cookies, unplugging/plugging in computer, restarting PC etc have not changed the situation. Any assistance or advice would be greatly appreciated. Thanks in advance.

  Read the article

• Virtual host config issues in osx 10.7 server app

  - by Benno

  I have two mac mini lion servers setup to run as production and staging machines. My sysadmin decided on these machines over the previous CentOS we had because it had an "interface" to be able to manage it, rather than just the terminal. To be honest, I prefer the terminal. My problem is, the mac osx 10.7 server.app seems to be having issues with the creation of virtual hosts in the 'Web' section. It seems VERY touchy. For example, I cannot create a http virtual host first. I have to create a https host first with a unique dns name 9e..g vuly6), then create the http host with a different dns name to the first (e.g. www), or it appears to override it the first one, even though one is ssl and one is non-ssl. Further, it seems to override perfectly good configurations at random. For example, the default sites directory is usually /Users/default/Sites/Customsites or something, but sometimes when I load the server.app it changes to /var/empty. Also, if I change or add extra virtual hosts after the first one or two, it starts to mess up and the first two virtual hosts start having issues. Has anyone had any experience with setting up virtual hosts via this app? Am I able to manually create these virtual hosts, without using the app, and without the app overriding my settings when I restart apache?

  Read the article

• Configuring OS X L2TP VPN to use Certificate for IPSEC layer instead of Pre Shared Key

  - by Matthew Savage

  I'm trying to setup a L2TP VPN on an OS X Snow Leopard Server setup, and have had success using a pre-shared key, however I would rather not rely on a simple string, and use a certificate instead. Setting this up on the server side is seemingly easy, you simply select a certificate you have generated from the list, and hit apply, however when I try to use the certificate on the client side it fails. I have exported the certificate into a P12 file, and then transferred to the client, and imported into the login keychain, however when I try to choose the certificate (from Network preferences, clicking Authentication Settings, then selecting Certificate and pressing Select) I am shown the following error: No machine certificates found Certificate authentication cannot be used because your keychain does not contain any suitable certificates. Use Keychain Access to import the certificate into your keychain. If you do not have the certificates required for authentication, contact your network administrator. Unfortunately even when I try to generate a certificate where I override the defaults, ensure the DNS name etc are set properly this doesn't change. When I select Certificate Authentication for the User Auth, and click Select the certificate for the server shows up there, but obviously this isn't where I need it to be available.

  Read the article

• Mac OS X L2TP VPN won't connect

  - by smokris

  I'm running Mac OS X Server 10.6, providing an L2TP VPN service. The VPN works just fine when connecting from all computers except one --- this one computer stays at the "Connecting..." stage for a while, then says "The L2TP-VPN server did not respond". In the console, I see this: 6/7/10 10:48:07 AM pppd[341] pppd 2.4.2 (Apple version 412.0.10) started by jdoe, uid 503 6/7/10 10:48:07 AM pppd[341] L2TP connecting to server 'foo.bar.baz.edu' (256.256.256.256)... 6/7/10 10:48:07 AM pppd[341] IPSec connection started 6/7/10 10:48:07 AM racoon[342] Connecting. 6/7/10 10:48:07 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 1). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 2). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 3). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 4). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 5). 6/7/10 10:48:11 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:14 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:17 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). ...and the "retransmit" messages continue until the error message pops up. So far I've unsuccessfully tried: rebooting deleting the VPN profile and recreating it verifying the client's internet connection (it is able to reach the VPN server) connecting through several different networks (in case a router was blocking VPN packets) disabling the Mac OS X Firewall on the client making sure that the VPN settings exactly match those of other working computers running software update (the client is on 10.6.3) Any ideas?

  Read the article

• Configuring DNS & MX records for exchange 2010

  - by Mahmoud Saleh

  i am trying to configure Exchange Server 2010 on Windows Server 2008 R2 to receive emails from the internet following the danscourses tutorials: and i followed this video for the DNS & MX records: http://www.youtube.com/watch?v=jdf_3DRssks i don't have any windows administration skills, and i am stuck with the DNS configuration. and the following are my domain configuration i got from the hosting. following are the steps i made: 1- Add new name server: add ns1.centors.com ip Exchange Server Public IP: 41.233.26.131 2- Change the A record change it to point to the public ip address Exchange Server Public IP: 41.233.26.131 3- New cname record for www and make it resolve to centors.com 4- New mx record for mail.centors.com 5- New A record for mail.centors.com: name: mail ip: Exchange Server Public IP: 41.233.26.131 6- new A record for ns1: ip: Exchange Server Public IP: 41.233.26.131 7- i made port forward in the router for SMTP and POP3 to the exchange server local ip address. ISSUE: i have a user account in the active directory, and the user is member of the domain, the user is [email protected] and when trying to login with this account in outlook 2010 on other machine using following data: account type: POP3 incoming mail server: mail.centors.com outgoing mail server: mail.centors.com i always get the error: Authorization failed, check your server settings. please advise what's wrong with the configuration, thanks in advance.

  Read the article

• Changing order of Thunderbird email address autocomplete?

  - by Brooks Moses

  I recently did a system wipe and installed Thunderbird 3.0, and imported all of my email setup from a previous Thunderbird 2.0 installation. Almost everything is working fine, but I'm having a problem with the autocomplete in email addresses when writing messages. The relevant behavior is this: In the old 2.0 installation, the autocomplete appeared to know which email addresses I used most frequently, and so when I typed "m" in the address line, it would pick as the default selection the "m"-person who I frequently write email to. (It's possible this is an illusion and it simply picked people in the order I added them to my address book.) Thus, I have become used to typing "m"-"enter" in the address field, and getting this person. In the current 3.0 installation, however, the autocomplete order has changed. It's not the same as it was, and it's not alphabetical. The result is that I'm spending extra time looking at the email address bar, and more annoyingly, half the time the old muscle-memory kicks in and I find myself with an email that's addressed to a couple of customers rather than to my boss and coworker. Thus, two questions: How does Thunderbird determine this autocomplete order, among a set of addresses all of which are in the same address book? How can I change this ordering to be what I want? (I have tried Google-searching, and found a number of incomplete answers, nearly all of which were for version 1.0 or thereabouts, and reference settings dialog boxes that no longer exist.)

  Read the article

• Exporting Environment Variables in Ubuntu Linux

  - by stanigator

  I know many people have asked about environment variables before, but I am having a hard time dealing with these paths while ensuring I don't mess around with the original settings. How would you go about executing these commands in Ubuntu in terms of environment variables? Thanks in advance! Please put /home/stanley/Downloads/ns-allinone-2.34/bin:/home/stanley/Downloads/ns-allinone-2.34/tcl8.4.18/unix:/home/stanley/Downloads/ns-allinone-2.34/tk8.4.18/unix into your PATH environment; so that you'll be able to run itm/tclsh/wish/xgraph. IMPORTANT NOTICES: (1) You MUST put /home/stanley/Downloads/ns-allinone-2.34/otcl-1.13, /home/stanley/Downloads/ns-allinone-2.34/lib, into your LD_LIBRARY_PATH environment variable. If it complains about X libraries, add path to your X libraries into LD_LIBRARY_PATH. If you are using csh, you can set it like: setenv LD_LIBRARY_PATH If you are using sh, you can set it like: export LD_LIBRARY_PATH= (2) You MUST put /home/stanley/Downloads/ns-allinone-2.34/tcl8.4.18/library into your TCL_LIBRARY environmental variable. Otherwise ns/nam will complain during startup.

  Read the article

< Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >