Search Results

Search found 16106 results on 645 pages for 'custom channel'.

Page 394/645 | < Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• How to play WAV file through Network Paging Interface

  - by BGM

  In our building we have a Viking Paging ZPI-4 Interface for our intercom. The interface receives data from our Asterisk Phone system via a Cisco SPA112 Port Adapter which has it's own IP address on the network and converts digital into analog. Asterisk plays the "5" tone and then allows the user's voice to commence over the connection. Now, what I want to do is to play a wav file over this Viking Paging device using the Cisco Port Adapter. I know how to get Asterisk to do it, but I want to do this without Asterisk. I want some kind of program that can talk to the Cisco Port Adapter and then transmit the wav file into the Viking Paging Device. What kind of program do I need to get or make? Now, I found this link if it helps anyone with ideas. I also found this information, but I'm not sure how to apply it. I also found this, but it involves an arduino. However, I already have the analog-to-digital convertor, and the Viking will handle sending sound over the paging speakers. I just need to know how to send the wav file to the Viking via the Port Adapter. So far, I know my wav file should be formatted as 8bit mono, and I need to send the "5" tone to open the Viking Pager's channel. [update] I am trying to figure out if I can use VLC player to stream to the ipaddress of the Port Adapter. So far I'm not having success with that, and don't even know if it will work. Windows Media Player has a streaming option too. I am thinking that since the Cisco Port Adapter thinks it is a sort of phone, that the only way this can be done is via SIP.

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• Mac Mavericks, ngircd localhost works, private IP doesn't

  - by user221945

  I have configured ngircd to listen on my private ip address. It doesn't. Localhost works fine. Configuration test: ngIRCd 21-IDENT+IPv6+IRCPLUS+SSL+SYSLOG+TCPWRAP+ZLIB-x86_64/apple/darwin13.2.0 Copyright (c)2001-2013 Alexander Barton () and Contributors. Homepage: http://ngircd.barton.de/ This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Reading configuration from "/opt/local/etc/ngircd.conf" ... OK, press enter to see a dump of your server configuration ... [GLOBAL] Name = irc.bellbookandpistol.com AdminInfo1 = Jaedreth AdminInfo2 = San Diego County CA, US AdminEMail = [email protected] HelpFile = /opt/local/share/doc/ngircd/Commands.txt Info = Server Info Text Listen = 10.0.1.5,127.0.0.1 MotdFile = MotdPhrase = "Welcome to irc.bellbookandpistol.com" Password = PidFile = Ports = 6667 ServerGID = wheel ServerUID = root [LIMITS] ConnectRetry = 60 IdleTimeout = 0 MaxConnections = 0 MaxConnectionsIP = 6 MaxJoins = -1 MaxNickLength = 9 MaxListSize = 0 PingTimeout = 120 PongTimeout = 20 [OPTIONS] AllowedChannelTypes = #&+ AllowRemoteOper = no ChrootDir = CloakHost = CloakHostModeX = CloakHostSalt = kBih5mu\kVI!DC6eifT(hd4m/0'zb/=: CloakUserToNick = no ConnectIPv4 = yes ConnectIPv6 = no DefaultUserModes = DNS = yes IncludeDir = /opt/local/etc/ngircd.conf.d MorePrivacy = no NoticeAuth = no OperCanUseMode = no OperChanPAutoOp = yes OperServerMode = no RequireAuthPing = no ScrubCTCP = no SyslogFacility = local5 WebircPassword = [SSL] CertFile = CipherList = HIGH:!aNULL:@STRENGTH DHFile = KeyFile = KeyFilePassword = Ports = [OPERATOR] Name = [REDACTED] Password = [REDACTED] Mask = [CHANNEL] Name = #BBP Modes = tnk Key = MaxUsers = 0 Topic = Welcome to the Bell, Book and Pistol IRC Server! KeyFile = As you can see, it should be listening on 10.0.1.5, but it isn't. After turning on Apache manually, port 80 works on 10.0.1.5, but port 6667 doesn't. It only works on localhost. Is there some terminal command I could use or some config file I could edit to get this to work?

  Read the article

• Ubuntu 9.10 RSA authentication: ssh fails, filezilla runs fine

  - by MariusPontmercy

  This is quite a mistery for me. I usually use passwordless RSA authentication to login into my remote *nix servers with ssh and sftp. Never had any problem until now. I cannot connect to an Ubuntu 9.10 machine: user@myclient$ ssh -i .ssh/Ganymede_key [email protected] [...] debug1: Host 'ganymede.server.com' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:14 debug2: bits set: 494/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: .ssh/Ganymede_key (0xb96a0ef8) debug2: key: .ssh/Ganymede_key ((nil)) debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering public key: .ssh/Ganymede_key debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Trying private key: .ssh/Ganymede_key debug1: read PEM private key done: type RSA debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password,keyboard-interactive debug2: we did not send a packet, disable method debug1: Next authentication method: keyboard-interactive debug2: userauth_kbdint debug2: we sent a keyboard-interactive packet, wait for reply debug2: input_userauth_info_req debug2: input_userauth_info_req: num_prompts 1 Then it falls back to password authentication. If I disable password authentication on the remote machine my connection attempt just fails with a "Permission denied (publickey)." state. Same thing for sftp from command line. The "funny" thing is that the exact same RSA key works like a charm with a Filezilla sftp session instead: 12:08:00 Trace: Offered public key from "/home/user/.filezilla/keys/Ganymede_key" 12:08:00 Trace: Offer of public key accepted, trying to authenticate using it. 12:08:01 Trace: Access granted 12:08:01 Trace: Opened channel for session 12:08:01 Trace: Started a shell/command 12:08:01 Status: Connected to ganymede.server.com 12:08:02 Trace: CSftpControlSocket::ConnectParseResponse() 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Status: Retrieving directory listing... 12:08:02 Trace: CSftpControlSocket::SendNextCommand() 12:08:02 Trace: CSftpControlSocket::ChangeDirSend() 12:08:02 Command: pwd 12:08:02 Response: Current directory is: "/root" 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Trace: CSftpControlSocket::ParseSubcommandResult(0) 12:08:02 Trace: CSftpControlSocket::ListSubcommandResult() 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Status: Directory listing successful Any thoughts? M

  Read the article

• GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Am I getting the right memory for my motherboard?

  - by Daniel Carvalho

  Hi technophiles; I have a Gigabyte GA-EP45-DS motherboard. Also, the memory that came with my computer was two Transcend aXe RAM 1066MHZ 1GB modules. The thing is, I noticed that my motherboard has "DDR2 1200" written on it. This concerns me, have I bought slower memory than my computer is supposed to have ideally? Now, I'm not super concerned at a granular level about the best optimal RAM with the best CAS latency etc... but I do hope at least that I've got the right speed. Now, as far as I know, there is no such thing as ram at 1200MHZ? Am I right? You see, because I'm thinking of getting more RAM now, before I can't find the same type or speed any-more and just want to make sure it's the right thing. Furthermore, if the memory is slower than what I should be getting for my motherboard, what RAM should I be getting, and will that new RAM play nice with my old RAM? If I get new RAM at a different speed, would it be better / more beneficial performance-wise to omit the old RAM because of how the whole DUAL channel RAM thing works? I'm not too clued up on this area. Thanks chiefs.

  Read the article

• Unable to access site over HTTPS using self signed certificate

  - by James

  I am developing a REST API which I want to secure with SSL/TLS. I have implemented a large part of the API which I have tested over HTTP, however, I am now at the stage where I want to switch it over to use HTTPS. At the moment the API is hosted on a Windows XP professional SP2 box running IIS 5.1 (development environment only) and I used the SelfSSL.exe tool from the IIS 6.0 Resource Kit Tools to generate a server certificate. I then configured my API to use this certificate which all appeared to work fine as I attempted to connect to my API using HTTP and I get a 403 response saying "... must be accessed over a secure channel...". However, the problem is when I attempt to access the same the API over HTTPS it just appears to hang! As this is a development environment at the moment I don't have a domain name (just a static IP address) and the API is running on port 81. Also (incase it matters) the API is the default site (I replaced it). Any ideas why I can't connect using HTTPS?

  Read the article

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• Downmix surround to Dolby Pro-Logic at the OS/driver level in Windows 7?

  - by davr

  First off, I'm talking about Dolby Pro-Logic, a really old tech for encoding 4 audio channels (L/R/C/SR) into two analog outputs, and then extracting them again. It was used in surround sound systems in the last century. I have a modern PC that can output 5.1 analog audio (Three outputs on the back carry six channels of audio). But I have a really old surround sound reciever that only has a two-channel, L/R input, which it extracts 4 channels of audio from, and outputs to 5.1 speakers. What I want is some way for the OS, Windows 7, to act as if I really had 5.1 audio channels available, so applications produce surround audio, but before outputting it out of the back of my PC, apply Dolby Pro-Logic matrix encoding so that it outputs over only two channels. These two channels would then get sent to my receiver via a RCA cable, which would decode it again and drive the surround speakers. Is anything like this possible? I'm pretty sure I could do it at an application / codec level, but I'm looking for something that I just have to set once.

  Read the article

• What Media Extender / Centre Set up should I use?

  - by Bryn Hird

  I have installed cat6 throughout the house which I use for telephony and network. In my cellar I have a NAS Server, gigabit switch and I want to install a Media Centre to stream my video's, music, photo's and live TV (coax from the aerial to the cellar) over the cat6. Yeah I know I can get stuff on the internet but shared experience of watching TV as a family as it happens is a big plus for live TV. I'm aiming for 1080p. I want different users to be able to watch different channels. Max users = 4. I've played a little with Windows Media Centre, works fine with live TV. Likewise I have XBMC up and running with live TV. The issue I have is what do I put near the TV. I'd like a consistent user interface (grandma and the the other technophobes in the house are continually pestering me on how to use different TVs, change channel, inputs etc.) so a key part of this for me is to make the user experience the same and simple i.e. no keyboards / PCs hanging around the TV. I've just bought a Linksys DMA 2200 to test the Windows Media Centre, but obviously off eBay as they're a dying breed. And with Windows Media Centre removed from Microsoft plans such devices will get rarer. And as for 1080p, think I can forget it with that set up. I have tested XBOX 360, also works but ditto on Microsoft plans for WMC. I was thinking of a WD Live TV to test the XMBC setup. Now to the question. Any advice on Media Centre / Extender setups that will do the job as above and have some degree of futureproofing (building my own with my Raspberry PI is a last resort). I'd like to understand the standards involved in the futureproofing if anyone knows (DNLA, RVU etc.).

  Read the article

• Can I connect a Playstation 3's HDMI output to my monitor's DVI-D input? [migrated]

  - by HankJDoomstorm

  I'm attempting to connect my Playstation 3 to my computer monitor. The monitor has a DVI-D (dual link) input, so before distinguishing between the different DVI varieties, I bought a DVI-I (dual link) to HDMI converter that won't fit into the port on the monitor (not only that, there isn't enough physical space in the back of the monitor to fit that much stuff before it hits the bottom of it). So I grabbed a DVI-D (single link) cable and got a female-to-female DVI-I coupler, and plugged the DVI-D cable into the monitor and the whole mess of converters. The end result was HDMI to DVI-D single link, but my monitor isn't receiving a signal on its digital channel. (For clarity's sake: DVI-D DL input on Monitor, DVI-D SL cable, DVI-I DL female-to-female coupler, DVI-I DL to HDMI converter, HDMI output on PS3) I don't know much about this stuff (obviously), but my educated guess is that the bandwidth of the PS3 is too high for the DVI-D Single Link cable, so nothing's getting through. Will replacing the single link cable with dual link resolve this? If not, is it possible at all? Oh, I should mention I'm aware I won't get audio through the monitor. I have an RCA to 3.5mm converter for that.

  Read the article

• Under FreeBSD, can a VLAN interface have a smaller MTU than the primary interface?

  - by larsks

  I have a system with two physical interfaces, combined into a LACP aggregation group. That LACP channel has two VLANs, one untagged (the "native vlan") and one using VLAN tagging. This gives us: lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether 00:25:90:1d:fe:8e inet 10.243.24.23 netmask 0xffffff00 broadcast 10.243.24.255 media: Ethernet autoselect status: active laggproto lacp laggport: em1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> laggport: em0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> vlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=3<RXCSUM,TXCSUM> ether 00:25:90:1d:fe:8e inet 10.243.16.23 netmask 0xffffff80 broadcast 10.243.16.127 media: Ethernet autoselect status: active vlan: 610 parent interface: lagg0 Is it possible to set a 9K MTU on lagg0 while preserving the 1500 byte MTU on vlan0? Normally I would simply try this out, but this is actually on a vendor-supported platform and I am loathe to make changes "behind the back" of their administration interface. This system is roughly FreeBSD 7.3.

  Read the article

• This .mpg video clip doesn't play well

  - by Roey

  I've installed K-lite mega codec pack v6.9.0 with playback essentials without player. My default and only media player is windows media player. here are the clip's media info: General Complete name : D:\Users\Roey\Downloads\B384MV.mpg Format : MPEG-PS File size : 273 MiB Duration : 4mn 59s Overall bit rate : 7 643 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@High Format settings, BVOP : No Format settings, Matrix : Default Format settings, GOP : M=1, N=15 Duration : 4mn 57s Bit rate mode : Variable Bit rate : 7 363 Kbps Nominal bit rate : 9 000 Kbps Width : 1 920 pixels Height : 1 080 pixels Display aspect ratio : 16:9 Frame rate : 25.000 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Compression mode : Lossy Bits/(Pixel*Frame) : 0.142 Stream size : 261 MiB (96%) Audio ID : 192 (0xC0) Format : MPEG Audio Format version : Version 1 Format profile : Layer 3 Mode : Joint stereo Duration : 4mn 59s Bit rate mode : Constant Bit rate : 128 Kbps Channel(s) : 2 channels Sampling rate : 44.1 KHz Compression mode : Lossy Stream size : 4.56 MiB (2%) Menu When I play it there is no sound (just a little "kahhhh" noise every 10-20 seconds) and the frames are moving very slow - it "jumps" frames. A blue tray icon [FFa] "ffdshow audio decoder" pops with the following details: Input:MP3, stereo, 44100 Hz (libavocodec) Output:PCM, stereo, 44100 Hz, 16-bit integer Any help will be much appreciated. Thanks

  Read the article

• Xen Bridge only working when IP Assigned

  - by m.sr

  Hey! Just had an (in my sense) obscure situation. I have a Xen Server with bridged networking. Everything works fine since month. A while ago i configuresd a second bridge. only some DomUs get an channel on this bridge - my Dom0 doesn't need to / should'nt use this bridge. So just 5 minutes ago while rebooting the xen host (because of an other problem with the UPS) i decided to removed the fixed ip from the the interface of the Dom0 which belongs to the second bridge. So after reboot i noticed that none of the interfaces on the second bridge is available. I couldn't find a problem. Everything was just like before the reboot, except the interface of the Dom0 had no IP address. After a while i tried to give the DomO interface of this bridge an IP again and ... BOOM ... everything is up and running again! WTF? Why is it important to have the interface of a bridge configured in the Dom0? Even when confiugured 'wrong' (complitely different netowkr settings as the network really hanging on the bridge) everythjing works fine ... I don't get it. Could please someone explain? Tnaks a lot!

  Read the article

• Intel Ethernet Bottlenecking Internet?

  - by Donald Darma

  I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

  Read the article

• Under what conditions will sendmail try to immediately resend a message instead of waiting for the standard requeue interval?

  - by Mike B

  CentOS 5.8 | Sendmail 8.14.4 I used to think that if SendMail experienced a temporary (400-class) error during delivery, it would place the message in a deferred queue (e.g. /var/spool/mqueue) and retry an hour later. For the most part, that appears to be the case. But every now and then, I'll notice log entries like this (email/domains renamed to protect the innocent :-) ) : Dec 5 01:43:03 foobox-out sendmail [11078]: qBE3l7js123022: to=<[email protected]>, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=124588, relay=exbox.foo.com. [10.10.10.10], dsn=4.0.0, stat=Deferred: 421 4.3.2 The maximum number of concurrent connections has exceeded a limit, closing transmission channel Dec 5 01:53:34 foobox-out sendmail [12763]: qBE3l7js123022: to=<[email protected]>, delay=00:10:31, xdelay=00:00:00, mailer=relay, pri=214588, relay=exbox.foo.com., dsn=4.0.0, stat=Deferred: 452 4.3.1 Insufficient system resources Dec 5 02:53:35 foobox-out sendmail [23255]: qBE3l7js123022: to=<[email protected]>, delay=01:10:32, xdelay=00:00:01, mailer=relay, pri=304588, relay=exbox.foo.com. [10.10.10.10], dsn=2.0.0, stat=Sent (<[email protected]> Queued mail for delivery) Why did Sendmail try again just 10 minutes after the first attempt and then wait another hour before trying again? If this is expected behavior, what scenarios will cause this faster requeue interval to occur?

  Read the article

• Desktop appliciations are unable to launch my browser in Windows 8

  - by Chevex

  I have a fresh copy of Windows 8 Pro installed from MSDN. I have Google Chrome installed (stable channel) and it is set as my default browser. I even went into Control Panel Default Programs to ensure that Chrome had all its defaults. When other desktop applications try to launch my browser they always fail. For example, while trying to install the Android SDK for Windows the installer accurately detected that I did not have the JDK installed. It provides a friendly button to visit java.oracle.com. When pressing this button, nothing happens at all. You can see that here: http://youtu.be/XXL8GhuWWg0 If it were only that application that was having issues I wouldn't think anything of it but I have been encountering similar issues all over the place. Probably the most irritating one is when visual studio has updates; clicking the update button does nothing. http://www.youtube.com/watch?v=zwd1mn3TId0 You can see in that screencast that Visual Studio is not able to launch the browser no matter what I click. The update button doesn't do anything and neither do the two links in the update's description. Any suggestions? I'm assuming it's a Windows issue since it is happening in multiple applications. UPDATE: Setting IE as the default browser fixes the issue. So it has something to do with it not being able to launch Chrome programmatically. Is it even possible to workaround this bug or do I have to suffer with IE as default for now?

  Read the article

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• Any dangers in using DDR memory with a higher frequency than the FSB?

  - by raw_noob

  I'm looking to upgrade memory in an older motherboard. The processor is an AMD Sempron 2500+ with a maximum speed of 333/166MHz. The motherboard is an MSI MS-7061 (KV3M-V), which accepts up to 2Gb of DDR memory maximum PC2700 in 2 slots and has a maximum FSB of 333MHz. The board does not have dual-channel support. Existing memory includes a stick of 512Mb PC3200, which seems to be running OK (presumably at PC2700) but is rated 200MHz, which is below the FSB speed. The other stick is 256Mb PC2100/133MHz, again below the FSB speed. (All figures from CPU-Z.) I have a chance to acquire a single used stick of PC3200/400MHz memory very cheaply. Crucial's system scanner seems to suggest that this will be OK with my system, but other sites have suggested that running memory with a higher frequency than the FSB can cause instability. Is this true? Would I be better waiting until I can buy the correct PC2700/333MHz stick? I'm assuming that the mixed memory I have at present is running as 768Mb at 133MHz. Is this a reasonable assumption? If so, would you expect the performance differences between 768Mb/133MHz and 1Gb/333MHz to be very noticeable? If I install the new 1Gb/400 or 333MHz stick in slot 1, am I right in thinking that adding back the existing 512Mb/200MHz stick in slot 2 would pull the whole 1.5Gb system memory speed down to 200MHz? If so, which would be better - 1.5Gb/200MHz, or the single 1Gb stick at the full 333MHz that the FSB permits? Is more headroom more important than extra speed? Any help - or even opinions - gratefully received. I can't find reliable information, and I can't afford to make expensive mistakes.

  Read the article

• Advice on Computer Specs for overall development/general use machine

  - by Ender

  At the moment I am restricted to a laptop with 512MB of RAM, a 120GB HDD and a 1.5GHz Intel processor for all my development and general browsing needs, and as you can probably tell using it for anything modern is a painful experience. As a result I've decided to buy myself a new desktop computer, one that will stand the test of time and one that can be upgraded easily. Rather than build the machine myself I've decided to go through Dell as I've had good experiences with them when purchasing computers for my family. I've had my eye on this as it's got a good amount of RAM, has a decent-rated processor and isn't priced too badly. http://www1.euro.dell.com/uk/en/home/Desktops/inspiron-580/pd.aspx?refid=inspiron-580&s=dhs&cs=ukepp1&~oid=uk~en~20211~inspiron-580_d005827~~ Intel® Core™ i5 Processor 750 (2.66GHz, 8MB) Genuine Windows® 7 Home Premium 64bit - English Display Not Included ATI Radeon™ HD 5450 1GB DDR3 graphics 6144MB Dual Channel DDR3 [3x2048] Memory 1TB (7200rpm) SATA Hard Drive DVD +/- RW Drive (read/write CD & DVD) with DVD Burn software 1 year of coverage included with your PC McAfee® Security Centre - 15 Month Protection - English After the pain of using a slow laptop for all this time the main thing I want is speed. I may look to play a couple of basic games on it, nothing too powerful. Obviously I'll be doing some development on it too so it'll have to be able to handle the latest IDE's and Database tools like SQL Server pretty quickly. Finally, should I ever need to improve it I'd like to be able to add more RAM and change some of the parts. I wouldn't have thought this would be a problem but a few people I've spoken to have said that the amount of RAM the motherboard can handle isn't that great. Is this true? How long can I expect to be using this computer before it's too slow? Thanks in advance for the help.

  Read the article

• Disabling LDAP Signing on Windows PDC in Local Policy

  - by Golmaal

  I just tripped over my own feet it seems. Playing around on a Windows 2008 R2 server (set up as domain controller), I was intrigued by certain warning event (event id 2886) which says: "To enhance the security of directory servers, you can configure both Active Directory Domain Services (AD DS) and Active Directory Lightweight Directory Services (AD LDS) to require signed Lightweight Directory Access Protocol (LDAP) binds." So I thoughtlessly did some Googling and set the relevant policies which enforce LDAP signing. Now I don't remember but I may have done that using Local Policy. Now I have setup a pfsense box which must authenticate AD users via LDAP. While the firewall can communicate over secure channel, it is difficult to manage the same for other packages such as Squid and SquidGuard. So now I have to disable i.e. undo those policy changes. The problem is that they are greyed out! The policies in question are LDAP server signing and LDAP client signing. I don't remember what I did but when I access these policies from Local Policy editor on the server, they are set to "Require Signing" and are greyed out. The same policies can still be set via Default Domain Controller option in Group Policy editor. So how can I reset these greyed out policies? Thanks

  Read the article

• Logitech Performance MX Mouse Jumps on OS X Lion (10.7.4)

  - by Adam Thompson

  I have a Logitech MX Revolution wireless mouse that I am trying to use with OS X Lion. Everything is working except for one problem... there is a small, but quite noticeable, jump when the mouse cursor is moved. The problem is mostly prevalent when dragging and dropping files or trying to highlight items. It makes performing any task with the mouse accurately next to impossible. I did quite a bit of looking and found that all kinds of people have had mouse issues with OS X. I've tried all of the following with absolutely no success: Using the official drivers from Logitech (these performed worse than the default mouse drivers in OS X) Using SteerMouse as a third party mouse driver. This worked ever so slightly better than the default driver, but still suffered quite frequently from the skipping problem Cleaning the sensor on the mouse and ensuring it's not the result of the surface that it's being used on. Tested the mouse on a Windows machine. The mouse worked absolutely flawlessly on the other machine. Changed the channel that my wireless router operates on by the off chance my problems were the result of interference. This also had no effect. I can't think of anything else that could possibly interfere with the mouse. I'm am out of ideas on what to try, so I would really appreciate if anyone has any suggestions. I should also mention that an old wired mouse I had laying around worked just fine when I plugged it in. This really isn't the best solution, however, as I really prefer the MX Revolution.

  Read the article

• Mac dev folder missing, SSH not working

  - by SamGoody

  A few days ago, SSH stopped working. When I try logging in a get the following message: PTY allocation request failed on channel 0 stdin: is not a tty fatal: unrecognized command '' Connection to 74.52.61.194 closed. Web searches have shown me that there might be something wrong with /dev/std. But my computer lacks a /dev/ drive. There is an Alias to /dev/ [hidden, but I've revealed hidden files to do this search], but when I try to open it I am told that it cannot find the folder it is aliasing. Now, many a web search tells me that without a dev folder, the computer doesn't work, but it does seem to work, except the SSH. Also, are there any tools that can save my SSH preferences so that I don't have to, each time, type out the username@adrees, password, path all of which are long and complex? Not looking for a Filezilla type client, there are many of those. Looking for a command line like putty, that lets me use bash on the remote client. Am on Macbook Pro, latest version of Tiger.

  Read the article

< Previous Page | 390 391 392 393 394 395 396 397 398 399 400 401  | Next Page >