Search Results

Search found 12395 results on 496 pages for 'interactive mode'.

Page 399/496 | < Previous Page | 395 396 397 398 399 400 401 402 403 404 405 406  | Next Page >

• Why does my simple Raid 1 backup storage perform really slow sometimes?

  - by randomguy

  I bought 2x Samsung F3 EcoGreen 2TB hard disks to make a backup storage. I put them in Raid 1 (mirror) mode. Made a single partition and formatted it to NTFS, running Windows 7. For some reason, accessing the drive's contents (simply by navigating folders) is sometimes really slow. Like opening D:/photos/ can sometimes take several seconds before it starts showing any of the folder's contents. Same applies for other folders. What could be causing this and what could I do to improve the performance? I remember that there was an option somewhere inside Windows to choose fast access but less reliable persistence operations (read/write). It was a tick inside some dialog. At the time, it felt like a good idea to take the tick away from the option and get more reliable persistence but slower access, but now I'm regretting. I'm unable to find this dialog.. I've looked hard. I don't know, if it would make any difference. Oh, and I've ran scan disk and defrag on the drive. No errors and speed isn't improved.

  Read the article

• Are these three brand new sticks of RAM really dead?

  - by David Brown

  I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

  Read the article

• Windows 7 not booting up and stuck at startup repair

  - by mikimr

  I've been having issues with Windows 7 Home Premium on a Lenovo laptop. At first, it would not start up normally at all. I started it in Safe Mode, where I disabled all non-MS services and tried again to no avail. It then goes into Startup repair where it failed several times. I tried copying the original registry settings, still the same. I resorted to booting with an Ubuntu DVD, where I ran the boot-repair, where it is supposed to correct the Windows boot. No luck. I used Win7 DVD to start up from there, where I had the option to install or repair. I chose the repair, got into command prompt, ran chkdsk /i /r, where it found 3 unreadable segments, went through the 2nd step without issues, and the 3rd step completed with some errors (can't recall the exact errors). When I restarted the machine, it went to straight to the Stratup Repair, indicating "Attempting repairs... Repairing dis errors. This might take over an hour to complete." It's been like this for nearly 15 hours. When I try to cancel or close the Startup Repair window, I get a message "The current repair operation cannot be cancelled." Should I let it run or force shut the machine? If force shut, how can I resolve this problem? Thanks.

  Read the article

• Need help toubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after restarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What I have done: I thought it was HDD at first, since this is the only part of the computer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from boo-table USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD appears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoroughly. The problem still persists, what should my next steps be?

  Read the article

• Input/output error reading USB backup drive on CentOS 6.4

  - by Kev

  I'm suddenly seeing some strange behaviour on our USB backup drive that doesn't make sense to me: (2013-10-21 14:58:23 [root@newdc /]$ cd /mnt/backup/ (2013-10-21 14:59:03 [root@newdc backup]$ ls -la ls: reading directory .: Input/output error total 0 (2013-10-21 14:59:05 [root@newdc backup]$ df -h /mnt/backup Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 843G 28G 97% /mnt/backup How is it possible for the OS to know how much is in use, but I can't ls any of it as root? Or more to the point, what problem does this indicate? /var/log/messages said this: Oct 21 14:57:54 g5 kernel: EXT4-fs error (device sda1): ext4_journal_start_sb: Detected aborted journal Oct 21 14:57:54 g5 kernel: EXT4-fs (sda1): Remounting filesystem read-only But...read-only is something different than 'throw an io error'... After unmounting to try fsck on it, I had someone on-site look at it, and the drive was not spun up, and had a slow-flashing light, which I believe means it was in a power-suspend mode. So I had them unplug and replug the USB cable, and now (before remounting) it says: fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) /dev/sda1: clean, 2805106/61046784 files, 181934167/244182016 blocks I then mount it and now ls works and df reports: Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 680G 191G 79% /mnt/backup What would cause it to go into such a state without being asked to? Why all the weird behaviour, and now it appears to not be corrupt?

  Read the article

• ssh - "Connection closed by xxx.xxx.xxx.xxx" - using password

  - by Michael B

  I attempted to create an new user account that I wish to use to log in using ssh. I did this (in CentOs): /usr/sbin/adduser -d /home/testaccount -s /bin/bash user passwd testaccount This is the error I receive when trying to log in via ssh: ~/.ssh$ ssh -v [email protected] OpenSSH_5.1p1 Debian-5ubuntu1, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to xxx.xxx.xxx [xxx.xxx.xxx.xxx] port 22. debug1: Connection established. debug1: identity file /home/user/.ssh/identity type -1 debug1: identity file /home/user/.ssh/id_rsa type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: identity file /home/user/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_4.3 debug1: match: OpenSSH_4.3 pat OpenSSH_4* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'xxx.xxx.xxx.xxx' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:8 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information No credentials cache found debug1: Unspecified GSS failure. Minor code may provide more information No credentials cache found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Offering public key: /home/user/.ssh/id_rsa debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Trying private key: /home/user/.ssh/identity debug1: Trying private key: /home/user/.ssh/id_dsa debug1: Next authentication method: password testaccount@xxx's password: Connection closed by xxx.xxx.xxx.xxx The "connection closed" message appeared immediately after entering the password (if I enter the wrong password it waits and then prompts for another password) I am able to log in from the same computer using other accounts that had been setup previously. When logged into the remote machine I am able to do 'su testaccount' Thanks for your time.

  Read the article

• Why is my rsync so slow?

  - by iblue

  My Laptop and my workstation are both connected to a Gigabit Switch. Both are running Linux. But when I copy files with rsync, it performs badly. I get about 22 MB/s. Shouldn't I theoretically get about 125 MB/s? What is the limiting factor here? EDIT: I conducted some experiments. Write performance on the laptop The laptop has a xfs filesystem with full disk encryption. It uses aes-cbc-essiv:sha256 cipher mode with 256 bits key length. Disk write performance is 58.8 MB/s. iblue@nerdpol:~$ LANG=C dd if=/dev/zero of=test.img bs=1M count=1024 1073741824 Bytes (1.1 GB) copied, 18.2735 s, 58.8 MB/s Read performance on the workstation The files I copied are on a software RAID-5 over 5 HDDs. On top of the raid is a lvm. The volume itself is encrypted with the same cipher. The workstation has a FX-8150 cpu that has a native AES-NI instruction set which speeds up encryption. Disk read performance is 256 MB/s (cache was cold). iblue@raven:/mnt/bytemachine/imgs$ dd if=backup-1333796266.tar.bz2 of=/dev/null bs=1M 10213172008 bytes (10 GB) copied, 39.8882 s, 256 MB/s Network performance I ran iperf between the two clients. Network performance is 939 Mbit/s iblue@raven $ iperf -c 94.135.XXX ------------------------------------------------------------ Client connecting to 94.135.XXX, TCP port 5001 TCP window size: 23.2 KByte (default) ------------------------------------------------------------ [ 3] local 94.135.XXX port 59385 connected with 94.135.YYY port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec

  Read the article

• Can not mount my USB disk-- Ubuntu nor windows[dmesg including]

  - by EthanZ6174

  first, here is my dmesn|tail result right after i plugged the disk: $ dmesg | tail [ 2578.697224] scsi 6:0:0:0: Direct-Access HP v100w PMAP PQ: 0 ANSI: 0 CCS [ 2578.698322] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 2578.916464] sd 6:0:0:0: [sdb] 3921920 512-byte logical blocks: (2.00 GB/1.87 GiB) [ 2578.916950] sd 6:0:0:0: [sdb] Write Protect is off [ 2578.916956] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 2578.916961] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.922460] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.922470] sdb: [ 2578.969570] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.969578] sd 6:0:0:0: [sdb] Attached SCSI removable disk there is nothing after 'sdb:' ... at the meantime, the lsusb shows: $ lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 004: ID 03f0:3207 Hewlett-Packard Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 002: ID 045e:0737 Microsoft Corp. Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub so... can anyone help me? what's wrong with my USB disk? THX

  Read the article

• Windows 7 doesn't start anymore

  - by 0xFF

  I've experienced some BSOD on windows 7 RC, and some freezing when startup, but today was big surprise, it doesn't start anymore. I tried to start on safe mode and no results too, it shows the starting animation, then a blue screen for less than a second and turns off immediately. The only thing I remember did today is update flash player under Firefox, then chrome stopped working even after logging off, and once restarting, it doesn't start anymore. Anyone experienced the same issue? any hints? [EDIT 3] Solved : Windows 7 have a very smart repair strategy, it works automatically, and it tried every possible fix, what fixed my problem was the system restore to a previous date, all this happened automatically. [EDIT2] these are the last lines in the ntbtlog.txt file Did not load driver \SystemRoot\System32\drivers\vga.sys Loaded driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Loaded driver \SystemRoot\system32\drivers\CHDRT32.sys Loaded driver \SystemRoot\system32\DRIVERS\VSTAZL3.SYS Loaded driver \SystemRoot\system32\DRIVERS\VSTDPV3.SYS Loaded driver \SystemRoot\system32\DRIVERS\VSTCNXT3.SYS Loaded driver \SystemRoot\system32\drivers\modem.sys Loaded driver \SystemRoot\system32\DRIVERS\usbccgp.sys Loaded driver \SystemRoot\System32\Drivers\usbvideo.sys [edit] this is the BSOD I get : http://twitpic.com/i87cx Thank you.

  Read the article

• can't register a soft phone to asterisk11

  - by Tom

  I have a VM (on oracle vbox) running Fedora17. I've installed asterisk 11 on it from sources. I've followed the wiki for installation (https://wiki.asterisk.org/wiki/display/AST/Creating+SIP+Accounts) to the letter. The ip on the VM machine running fedora is 192.168.1.7 and I can ping it from the host machine (Ubuntu 12.04), which is at 192.168.1.2 I've tried registering with ekiga with the following settings: user: [email protected]. Password: verysecretpassword registar: 192.168.1.7 but I'm getting an error "transport fail". Also, while trying to register I'm logged in to the asterisk CLI with verbose level 3 and debug level 4 and nothing appears. some more relevant data: I've added the following code to the end of my sip.conf.sample file: [demo-alice] type=friend host=dynamic secret=verysecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 [demo-bob] type=friend host=dynamic secret=othersecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 After I changed the sip.conf.sample file, I've created a copy of it and named it sip.conf. then I logged in to the asterisk CLI and typed sip reload. Then I'm trying to register and ekiga client from my host machine at 192.168.1.2 but it doesn't work and nothing appears on the asterisk CLI while in verbose mode level 3. BTW, If there is missing information about my question, please don't close it. comment about what you need to know and I'll edit it in to the question. tnx.

  Read the article

• sql server 2005 instance unresponsive and all db's are 'in recovery'

  - by user44650

  we've got a sql server 2005 instance that one of our guys messed up, i believe they killed the sql server service and restarted the computer, and when it came back all of our databases are "in recovery" and it times out every time we try to connect to it. it's been 'in recovery'and unable to connect to 'msbd' (also in recovery) whenever we try to use SSMC, for the last 4 days now. i'm unsure how to use the DBCC CHECKDB command to check the db integrity. we have backups(which we can't recover from because it keeps timing out), and it's a testing server, so nothing in production is really lost. is there any way to get it out of recovery mode? we have another sqlserver instance running that's just fine, but this instance keeps timing out. the errors i keep seeing are database msdb is being recovered. wait until recovery is finished and an exception occurred while executing a transact-sql statement or batch Timeout expired. any thoughts? we don't really have a DBA here, or anyone with much sql experience.

  Read the article

• Windows 7 PC freezes frequently with hard disk light constantly on

  - by Senthil

  I recently replaced a defective hard disk with a new one - Windows 7 - "A disk read error occured. Press Ctrl + Alt + Del to restart" I have been using the new hard disk with a Windows 7 installation for about 4 days. Now it has started freezing frequently. Sometimes every 2 minutes and sometimes every 10 seconds. There is lots of software installed - I am a developer and my PC is full of IDEs, database servers, web servers, developer tools, testing tools, all browsers etc.. My windows is up to date as of now. I have installed ALL updates including optional drivers etc. All my installed software is up to date. I scanned my computer using Microsoft Security Essentials and found nothing malicious. I did a chkdsk /r and found no problems. I did a memory diagnostic and found no problems. When I go into safe mode, it doesn't freeze and I am able to use it normally for longer periods of time. What other steps can I take to locate the problem?

  Read the article

• Windows 7 not booting after failed SRT (SSD caching) install

  - by david

  This is a fairly new computer, only about a month old. i7 2700k, z68 motherboard, with a 1.5tb WD black HD, and a 128gb crucial M4 ssd. I followed the instructions for setting up ssd caching, the SATA controller was set to RAID, I installed the intel software and enabled acceleration and it said everything went fine. But when I went to reboot, I received the lovely "Reboot and Select proper Boot device" error message. I checked the bios, and it was booting from the correct HD (I tried the only other option anyway just in case, it was the ~50 odd gb of unformatted space left on the SSD) AFter that I entered the raid until (ctrl-i at boot) and removed the acceleration and deleted the raid array (because it was being used as a cache this was non destructive) Still no boot. So I reinstalled win7 directly on the SSD, booted, and checked the HDD to make sure it hadn't been wiped. It hadn't, all the files were still there, including all the windows stuff. I backed up my data to an external drive just in case, but I'd really like to get this install booting again. I trawled the webs a bit, and have tried entering recovery mode and using the bootrec.exe and bootsect.exe to fix it, but to be honest I'm not sure what I'm doing with those. My question is basically: How do I make my harddrive bootable again?

  Read the article

• Outlook 2010 Crashing Unpredictably

  - by cbkadel

  Very often when I open up Outlook 2010 and start doing actions in it, it will hang and become non responsive. I have tried letting it finish, but it never does come back (up to 20 minutes of letting it try). I generally have to restart Outlook and try again. Usually after about an hour of doing this, Outlook somehow snaps out of it and works for the rest of the day. It's generally in the morning (though I doubt that's the key variable). Generally, the emails that cause problems are HTML/formatted, but not always. What I've done so far to troubleshoot: Install Latest Outlook Hotfix (I think Dec 14, 2010) Start Outlook in Safe Mode Neither of those steps seem to make a difference. Usually - after about 10-15 restarts of Outlook on any given day, then it starts working thereafter. My next step is to uninstall/reinstall Office 2010, but I'm hoping someone has seen this and knows what to do about it - though not sure. My configuration is like this: Microsoft Online Services (using Microsoft's Sign In App) - Connecting to Exchange I have two other Exchange accounts in this profile (new feature in 2010) connected through Outlook Anywhere. Life Meeting Conferencing Add In I've disabled the People tab/add in. I've disabled the "Send to Bluetooth" add-in. Not sure what else to do?

  Read the article

• INACCESSIBLE_BOOT_DEVICE after installing Linux on same drive

  - by kdgregory

  History: My PC was configured with two drives: an 80G on IDE 0 Primary that was running Win2K, and a 320G on IDE 0 Secondary that was running Linux (Ubuntu). I decided to pull the 80Gb drive out of the system, so dd'd the entire 80 G drive (/dev/sda) onto the 320 (/dev/sdb) -- this included the MBR and partition table. Then I pulled the drive, plugged the 320 into IDE 0 Primary, and rebooted. The Windows partition worked at this point. Then I installed Ubuntu into the remaining space on the 320. It works. However, when I try to boot into Windows, I get a BSOD with the following message: *** STOP: 0x0000007B (0x89055030,0xC000014F,0x00000000,0x00000000) INACCESSILE_BOOT_DEVICE Before the BSOD I see the Win2K splash screen, and it claims to be "starting windows" for a couple of seconds -- so it appears that the first stage boot loader is working as expected. Ditto when I try booting in Safe Mode. After reading the Microsoft KB article, I booted into the recovery console and tried running chkdsk /r. It refused to run, claiming that the drive was corrupted (sorry, didn't write down the exact error message). However, I can mount the drive from Linux, and access all files. And for what it's worth, I can scan the drive using the Linux "Disk Utility" (this is Ubuntu, the menus don't show real program names), it claims the drive to be clean. The KB article mentioned that boot.ini could be the problem, so here it is: timeout=10 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows 2000 Professional" /fastdetect Any pointers on what to do next?

  Read the article

• How to copy VirtualBox VDI contents to a partition and dual boot the OS from it?

  - by Calmarius

  I'm a Linux user but I keep a compressed Windows XP ISO with me on a pen drive for the case I absolutely need Windows to do something. This works in VirtualBox most of the time. But now I want to play some games, so I would like to run the Windows image natively. My computer don't have CD drive so cannot just burn the ISO and make an install normally. What I trying to do is moving the installed Windows image to a physical NTFS partition on my HDD and set up GRUB to let me dual boot it. I found many tutorials that deal with making VDI to physical drive. But they assume I want to overwrite my entire drive. Moving the raw disk image with dd to the partition resulted in a corrupt partition. I also tried the VMDK trick to use that empty partition and install the Windows on it. Although the text mode phase of the installation finishes without problems, the VM won't work, either crashes and keeps rebooting or just immediately or freezes (depending on how I created the VMDK, with -rawdisk /dev/sda3 or -rawdisk /dev/sda -partition 3).

  Read the article

• Expanding raidz vdev

  - by Blubber

  I'm currently planning on installing FreeBSD 9 on my home server. The machine has 4x 1.5TB disks, and at some point, when HDD prices drop I'll be upgrading to something bigger, perhaps 3TB. The disks are connected to an IBM ServerRaid m1015 in IT mode, this card has room for up to eight disks. Now here is the problem, currently the 4x 1.5TB will be connected to the m1015. Then when prices drop I'll be adding something like 4x 3TB, also connected to the m1015. No problem yet, I can just run 2 raidz2 vdevs and put them in the same pool. But, at some point the 1.5TBs will start to break, or I will have to upgrade them when the pool runs out of space. So I started researching if it's possible to expand a raidz vdev, and I found several pages explaining the same procedure, like this on SF: How to upgrade a ZFS RAID-Z array to larger disks on OpenSolaris?. So I went a head and tried that in vmware, I installed FreeBSD 9 and created 6 virtual disks, 3 of 1GB each and 3 of 10GB each. After building a raidz vdev of the 1GBs I replaced them one by one with the 10GB, but the pool did not increase in size. Is this a limitation of the ZFS implementation in FreeBSD? Or am I just doing something wrong?

  Read the article

• After RAID failure SBS 2008 issues logging in and Exchange store does not mount

  - by Josh R

  today has been one of those days. Yesterday a hard drive in our Dell Poweredge 2900 server failed and the RAID array didn't degrade gracefully, so I called Dell (Server still under warranty) and got an engineer to work though the RAID issues with me. He was a nice guy but didn't do too much. We tried to put the RAID in a state where it was bootable and even though we only lost one disk there are still issues with the server. Once we got the server to boot there was an error message saying that the logonui.exe was corrupted and we needed to run chkdsk. I clicked through the error messages and the login screen never came up. So I power cycled the server and it chkdsk automatically but the login screen didn't appear. I tried safe mode, no difference there either. So the issues I am currently having are: 1) The server boots up, the loading windows screen comes up then it dumps me into a black screen where I can only see my mouse cursor. Ctrl+Esc doesn't work Ctrl+Alt+Del doesn't work 2) Some of the services come up: DHCP, DNS, DFS, and Print come up 3) The exchange information store and transport service don't start - I tried using mmc to connect to services.msc on the computer and start them but they throw an error message of "Can't start because group or dependency failed" Has anyone had a problem like this? Can anyone offer some guidance? Thanks a bunch!

  Read the article

• Sudden "No Signal" in HDMI-DVI connection

  - by nazikus

  Yesterday I have connected external display Asus VW192C to my laptop Dell XPS 14-L421X via HDMI-to-DVI-D cable. And it worked perfectly fine from start. The day after, Asus screen went blank showing "No signal". Every time I connection/disconnection cable or power off/on the display it says "No signal". And I didn't change any system configurations meanwhile. To troubleshoot the problem, I have tried to connect laptop to TV (hdmi-to-hdmi) - it was fine. I've tried to connect a different laptop to the display via the same cable - worked fine as well. So its obviously something on system level, either Windows or graphics drivers. Also it seems that Windows still see the external display (I can move mouse pointer away from the main screen in Extended mode), but there's just no signal. Any ideas? What else to try? PS. My laptop has 2 graphics cards - GeForce 630M and Intel HD 4000 using NVidia Optimus technology. I have updated to latest Intel and NVidia drivers, still didn't help. PPS. Although I shouldn't have updated (from Intel support): "our Intel generic graphics drivers from the Intel website do not support using both Intel Graphics 4000 and NVidia GeForece GT630M". Nevertheless, it should not affect connectivity to additional display.

  Read the article

• Why does my ftp(e)s server fails like half of the time

  - by user1092608

  I have this discussion at work regarding our ftp server running via vsftpd. Initially, we have opted to serve ftpes instead of sftp because this seemed the most flexible and straightforward solution for our server to have secure file transmission. Afterwards, our ftp server seems to be a source of issues for our end users. Half of the time, users complain about not working ftp connections. I must say, i tested our FTP trough different infrastructures (=in the field, at random times at random places) and indeed, sometimes behind some configurations (=no idea how they are configured, because the 'field' testing), i recieve errors. Some of the are: Error: Failed to retrieve directory listing (filezilla) Furthermore, behind my basic home configuration, everything seems to be running fine. I (think I) did all the basic configuration checks (passive mode?, firewall for all ports?, ...) and can't seem to find the source. Being a bunch of techies at our small office, yet knowing nothing about infrastructure, some start suggesting that ftps protocol could be the source of issues. ("No, i only knew sftp so far" "Ftps is not widespread"). I, however, strongly doubt this hypothesis, since reading around on the www, asking questions on serverfault, everyone seems to deny this. So, as I would like to avoid reconfiguring, since this involves messing around in our SSH service, our virtual user setup and ftp service, i would need some advice on 1) what could be potentially the general cause? 2) do you have some general tips? 3) would you mind having a look at my configuration file? ----- General Settings ----- write_enable=YES dirmessage_enable=YES nopriv_user=ftpsecure ftpd_banner="Welcome to XXXX FTP!" hide_ids=YES hide_file=.* max_per_ip=10 max_clients=10 local_enable=YES local_umask=022 chroot_local_user=YES secure_chroot_dir=/usr/share/empty userlist_enable=NO userlist_deny=YES userlist_file=/etc/vsftp_deny_users guest_enable=YES guest_username=ftpvirtual virtual_use_local_privs=YES user_sub_token=$USER local_root=/srv/ftp/ftpvirtual/$USER anonymous_enable=NO syslog_enable=NO xferlog_enable=YES xferlog_file=/var/log/vsftpd_xfer.log connect_from_port_20=YES pam_service_name=vsftpd listen=YES listen_port=21 pasv_enable=YES pasv_min_port=30000 pasv_max_port=30030 pasv_address=foo ssl_enable=YES rsa_cert_file=/etc/vsftpd.pem rsa_private_key_file=/etc/vsftpd.pem force_local_data_ssl=YES force_local_logins_ssl=YES ssl_tlsv1=YES ssl_sslv2=YES ssl_sslv3=YES ssl_ciphers=HIGH anon_mkdir_write_enable=NO anon_root=/srv/ftp anon_upload_enable=NO idle_session_timeout=900 log_ftp_protocol=NO dsa_cert_file=/etc/vsftpd.pem Thanks

  Read the article

• Need help ttoubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after rstarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What i have done: I thought it was HDD at first, since this is the only part of the coputer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from bootable USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD apears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoughrouly. The problem still persists, what should my next steps be? Thanks in advance.

  Read the article

• Changing the View of a Folder When It Is Opened from Finder

  - by user60044

  When I was running OS 10.4 I had all my folders beautifully organized with position and which ones should be opened in View mode and which one in Icon, etc. When I transitioned to 10.6 I found that OS ignored all that information and imposes an awful consequence of changing the view for some folder and that view moving up to all parent folders which don't have their views locked. The only way I can think of to get this functionality back is to either write a program that given a root directory will enumerate it setting the views based upon a static template I have. The other way I thought I could accomplish this is by Folder Actions. Aside from the fact that I don't know AppleScript it seems folder actions cannot be inherited. Since I have 1000s of folders involved here, all being inherited from a single root, I could not possibly manually add that action to each of those folders. What I would like to have is a folder action that whenever I open the folder from Finder, then if it contains any JPG, GIF, etc. type image files that it will automatically open that folder with a view of Icon with a reasonable size to support the number of images. If the folder contains only folders, then to open that folder in the list view. Does anyone have anything that could do this for me? Thank You, -- Mark

  Read the article

• Can you help me understand my SATA/RAID options?

  - by andrz_001

  I've a gigabyte GA-M720-US3 motherboard. Recently, I noticed the following during boot: IDE channel 0 Master (none) IDE channel 0 Slave (none) IDE channel 2 Master (my hdd) IDE channel 2 Slave (my dvd drive) IDE channel 3 Master (none) IDE channel 3 Slave (none) Of course, the same information is contained in the BIOS/CMOS. The HDD is connected to the mobo via a SATA(2?) cable at the port(?) labeled SATA2_0. The DVD drive is connected by a similar cable at SATA2_1. Why doesn't the information displayed during the boot and in BIOS reflect how I plugged the cables in? I mean, why "none" for channel 0 when there is something in SATA2_0. (or is that serious naivete on my part!?) Where's Channel 1 master and slave? Since these are SATA cables and not the IDE ribbons from a time ago, why the whole master/slave declaration during boot and in BIOS? Should my BIOS reflect the fact that these are SATA cables? I mean, in BIOS, should the "Onchip SATA mode IDE" be set to RAID or AHCI instead of IDE? Any replies, answers, suggestions, links, tips will be much appreciated. Thank you in advance!

  Read the article

• Windows 7 Laptop Randomly Sleeping

  - by Josh Arenberg

  I'm running Windows 7 64-bit on a Lenovo laptop, and I have a problem wherein after I've put it to 'sleep' once, it will seemingly without any reason or warning go back to sleep every 10 to 15 minutes after that. Each time it wakes back up just fine, and you can happily continue on. However, 10 or 15 minutes later, it just drops out into sleep mode. I don't see any errors in the system logs. I don't think it's related to heat ( since it's not rebooting ). When I check the system event log, I can see where the machine goes to sleep, but it simply says "reason: application API", and doesn't indicate which app ( brilliant ). I don't see any errors from hardware or anything relating to sleep in the application log that would point to what is going on either. How can I find out which app is triggering this? EDIT: I confirmed that temperature wasn't the issue. I think it's important to keep in mind that this condition only happens after the first sleep. If I reboot, the problem goes away until I put it to sleep, after which it sleeps on it's own every few minutes. Is there no way to capture which app is calling the sleep routine?

  Read the article

• Using multiple USB webcams in Linux

  - by rachelderp

  Running more than one USB webcam in Debian/Linux results in the the following error: libv4l2: error turning on stream: No space left on device VIDIOC_STREAMON: No space left on device What initially seemed to be a programming issue in OpenCV turned into a quest for a mysterious hardware/software problem after the same errors were produced by running cheese and xawtv. Apparently it's caused by webcams requesting all the available bandwidth on the USB host controller. With that in mind I decided to run wireshark and capinfos to see just how much bandwidth a single camera used. 4 megabits per second at 320x240 14 megabits per second at 640x480 32 megabits per second at 1920x1080 Interesting! That might explain why two cameras at 320x240 work but any higher resolution fails. It's as if my USB controller is only operating at USB 1 speeds, yet lsusb shows both webcams belonging to a device which supposedly supports 480 megabits per second. One solution proposed forcing the webcams to calculate their bandwidth usage instead of requesting their maximum by running the following commands: sudo rmmod uvcvideo sudo modprobe uvcvideo quirks=128 Unfortunately that made no difference, so I decided to try another solution. A post on StackOverflow suggested telling my webcams to use a lower FPS or compressed video format like MJPEG, but after running v4lctl list it doesn't appear either of my webcams support changing their video mode. And that's where I'm stuck. Why would two webcams operating well below the maximum speed of USB 2 would produce this error? ps: It's not a disk space issue, df displays no change when the webcams are started. pps: If it makes a difference, here's the output of lsusb

  Read the article

< Previous Page | 395 396 397 398 399 400 401 402 403 404 405 406  | Next Page >