Search Results

Search found 1181 results on 48 pages for 'cisco asa'.

Page 40/48 | < Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >

• FCoE, on any Ethernet switch?

  - by javano

  I understand the concept of FCoE. I have looked at the Wikipedia page and looking at the layer 2 frame diagram, it looks like FCoE really should "just work" on any Ethernet switch, but is this really the case? If so, what do switches like Cisco's Nexus 5k or 6120P offer that normal switches don't (in specific relation to FCoE)? I am just using those two switches as examples. On the Nexus 5548UP page for example it says the following; Unified ports that support traditional Ethernet, Fibre Channel (FC),and Fibre Channel over Ethernet (FCoE) Well if FCoE runnins over regular Ethernet, that why does it support "Ethernet and Fibire Channel over Ethernet"? This is why I am curious as to weather FCoE will run on any Ethernet switch and these switches just support "bonus" features, or if you do indeed require a specialist switch. Thank you.

  Read the article

• Security tips for adding wireless AP to domain network?

  - by Cy

  I am researching best-practices for adding wireless to our existing domain network. My DHCP server is running Windows Server 03 Standard (not sure if thats useful). I am familiar with simple home networking but I thought I'd get some expert advice for the more advanced stuff. Any tips and / or best-practices? Is this Cisco Wireless Access Point a good option? Are there any additional hardware recommendations? Thank you in advance for your help.

  Read the article

• Why does my wifi fail to stay connected?

  - by Mark0978

  We have 5 different laptops in the house, 1 macbook, 1 Compaq, 3 dells, plus numerous little devices like ipods, squeezeboxs, squeezebox radios and controllers, you name it. All of them connect to and stay connected to the "downstairs" WIFI just fine. But my laptop (the most expensive of the lot) refuses to stay connected, preferring the much weaker and slower signal upstairs. My laptop is running Win7 (64 bit) Ultimate with an Intel 3945ABG WIFI contoller (It's a Dell Precision M6300). The WIFI Access Point is a Cisco WRT54G2 V1 with firmware: Firmware: DD-WRT v24-sp2 (10/10/09) micro Time: 11:11:10 up 42 min, load average: 0.06, 0.01, 0.00 WAN: Disabled

  Read the article

• A Linux DHCP server that will listen on an non-broadcast (tap) interface?

  - by TomOnTime

  Are there any Linux DHCP servers that will listen to what Cisco calls an "unnumbered" interface, or what others might call a "NBMA" (non-broadcast) interface. I have a Linux system that connects to a number of others using GRE tunnels. The machines on the other end send DHCP requests to this machine, I can see them with tcpdump. However, ISC DHCP 3.0.3 refuses to listen to the interface because it is non-broadcast. The interface I'd like DHCP to listen to is: tap2 Link encap:Ethernet HWaddr removed-for-privacy inet6 addr: removed-for-privacy/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:518 errors:0 dropped:0 overruns:0 frame:0 TX packets:510 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:196242 (191.6 KiB) TX bytes:52425 (51.1 KiB)

  Read the article

• How to connect a remote IP Phone to our VOIP Network?

  - by Mistiry

  We have an IP phone system in our office, and about 8 VoIP phones running on the system. We have a remote worker, who is literally states away. We'd like to connect his phone to our VoIP network, so that he has a business phone and an extension to which we could transfer calls. I was thinking, although I don't know for sure, that a pair of Cisco routers could be used in some way to make this work. I imagine a VPN solution, where I have one router connected to the phone network and the other router connected to the remote phone. Then have a site-to-site VPN set up so that the remote router... And that's where I'm stuck. I know the remote router will need to use the DHCP server of the phone system. I've never set up something like this, so I am seeking the help of the community here. What is the best way to get this remote VoIP phone RELIABLY connected to our internal VoIP network?

  Read the article

• DVD player Ubuntu 9.10

  - by pcguynardone

  Hello everyone at SeverFault. I am new to this fourm. I have been using ubuntu since 8.04. Here is my problem. When I try to watch one of my cisco videos I get wmas error. I never had to use this format before. I went on ubuntu fourm they told me to use vlc media. I am using vlc media. mplayer, it still have error with that, sounds and video. Is there a program that I could use to watch wmas files on my ubuntu 9.10. It is a laptop ACer Extensa 5620z. Thank you for who ever will help !!

  Read the article

• DVD player Ubuntu 9.10

  - by pcguynardone

  Hello everyone at SeverFault. I am new to this fourm. I have been using ubuntu since 8.04. Here is my problem. When I try to watch one of my cisco videos I get wmas error. I never had to use this format before. I went on ubuntu fourm they told me to use vlc media. I am using vlc media. mplayer, it still have error with that, sounds and video. Is there a program that I could use to watch wmas files on my ubuntu 9.10. It is a laptop ACer Extensa 5620z. Thank you for who ever will help !!

  Read the article

• Bluetooth Headset drivers on Windows 7

  - by Tom Ribbens

  I have a Dell Precision with integrated bluetooth from work. I wanted to connect either one of my two bluetooth headsets (Plantronics UC Voyager Pro v2 and Sennheiser MM450X) in order to make calls with it using our Cisco IP Communicator. In both cases, the bluetooth pairs ok. Then Windows tries to install drivers, and fails, leaving the device useless. The devices work perfectly with my phone and tablet (both android). What can I do to get it to work? I can't seem to find drivers on either the Plantronics or the Sennheiser site. I am using the Plantronics without the USB dongle they provide, because that is temporarily misplaced :).

  Read the article

• Hp Procurve Switch : port filtered

  - by user117140

  My HP Procurve switch is blocking port 22 and I dont know how to unblock it.Please let me know From the server, see port 22 is blocked [root@server ~]#nmap -p22,80,443 10.247.172.70 Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2012-04-16 14:12 IST mass_dns: warning: Unable to determine any DNS servers. Reverse DNS is disabled. Try using --system-dns or specify valid servers with --dns_servers Interesting ports on 10.247.172.70: PORT STATE SERVICE 22/tcp filtered ssh ------------------> see 80/tcp filtered http 443/tcp filtered https This is blocked on cisco switch but I dont have any clue how this is done. I know that vlan is configured on switch. vlan 54 ip ospf 10.247.172.65 area 0.0.0.10 vrrp vrid 54 owner virtual-ip-address 10.247.172.65 255.255.255.192 priority 255 enable exit exit Please let me know how to unblock ssh port 22 access on this switch?

  Read the article

• Multicasting Windows 7 Image

  - by LawnChairSkank

  I am trying to deploy some new machines with windows 7 for the first time in our computer labs. We used to use third party imaging software and then run sysprep after the image was copied(XP), but it seems you can't go that route with windows 7. We set up a new imaging server with the windows system image manager, but when we try to multicast the image it pretty much takes down our whole staff and faculty network. I heard you can turn on a multicast feature on our cisco switches to help with the issue, but that it also slows the switches to a crawl. Another idea we have tried was pulling the the computer lab switch off the main network and plugging the imaging server directly into the computer lab switch so the multicast doesn't take down our network, but it doesn't seem to work without being able to hit a domain controller. Is there a way to multicast without taking out the network? I feel like I am missing something... Thanks in advance

  Read the article

• Putting a Windows DC, Exchange in a DMZ

  - by blsub6

  I have one guy at my company telling me that I should put FF:TMG in between my main Internet-facing firewall (Cisco 5510) and put my Exchange server and DC on the internal network. I have another guy telling me that I should put the Exchange server and DC in a DMZ I don't particularly like the idea of having my mailboxes and DC's usernames/passwords in a DMZ and I think that Windows authentication would require me opening up so many ports between my DMZ and my internal network that it would be a moot point to have it out there anyways. What are some thoughts? How do you have it set up?

  Read the article

• Comunication from Server to Client + Client LAN

  - by Filipe YaBa Polido

  I'm having some trouble with some network setup. I've tried OpenVPN, SocialVPN, Hamachi, still it is not working. This is my setup: Server A: NIC 1 with internet public address, NIC 2 to LAN Client B PC: NIC 1 (192.168.10.2) connects to router 192.168.10.1 Client B Device: 192.168.10.3 (Configured via software, can't do much here) Problem: Server A must connect to cliente device B. (I can install software needed at Client B PC). However... I can't change the router to some model with VPN like Draytek or Cisco :( OpenVPN fails at bridging, PC B can ping Server A, but Server A can't ping Device B, only PC B. What else can I do?!?!?

  Read the article

• Is there a sensible way of 'teaming' two ADSL connections?

  - by Tim Long

  I work in an office complex that has two seperate ADSL connections, which they use to provide two seperate networks (actually both the ADSL routers go into a Cisco managed switch with two VLANs, one for each ADSL connection). Circumstances have changed so that 95% of the users are all on one ADSL connection. It would be great if there were a way to join together both connections to emulate a single connection at double the speed, but the ISP doesn't support bonding. So, is there a sensible way to take two completely seperate ADSL lines and use them to provide a single internet gateway?

  Read the article

• Connect macbook to my LAN through a VPN - best solution?

  - by LewisMc

  So I have a LAN connected via a ADSL/PPPoA, this is using a bog-standard DLink router supplied by my ISP (talktalk UK). I have a NAS within the LAN that is running FreeNAS and I want to be able to connect to it when I'm out and about. It's running an atom so it's quite low on juice consumption but I don't want to have it on all day and night so I've been waking it via a magic packet and booting it down from the web admin when I need it. So I want to connect to the LAN, I presume via a VPN, to be able to send a magic packet. But what is the best method to accomplish this, or is there an easier way? I've been looking at the cisco 857 integrated router and the Netgear prosafe 318(behind modem) but not sure If I'm on the right track with what I want to achieve as I've not much experience or knowledge with VPN's or networking (software engineering student). I have tried port forwarding but to no avail, either with magic packets or even connecting outside the LAN via DYNDNS. Thanks,

  Read the article

• Methodologies for performance-testing a WAN link

  - by Chopper3

  We have a pair of new diversely-routed 1Gbps Ethernet links between locations about 200 miles apart. The 'client' is a new reasonably-powerful machine (HP DL380 G6, dual E56xx Xeons, 48GB DDR3, R1 pair of 300GB 10krpm SAS disks, W2K8R2-x64) and the 'server' is a decent enough machine too (HP BL460c G6, dual E55xx Xeons, 72GB, R1 pair of 146GB 10krpm SAS disks, dual-port Emulex 4Gbps FC HBA linked to dual Cisco MDS9509s then onto dedicated HP EVA 8400 with 128 x 450GB 15krpm FC disks, RHEL 5.3-x64). Using SFTP from the client we're only seeing about 40Kbps of throughput using large (2GB) files. We've performed server to 'other local server' tests and see around 500Mbps through the local switches (Cat 6509s), we're going to do the same on the client side but that's a day or so away. What other testing methods would you use to prove to the link providers that the problem is theirs?

  Read the article

• How to configure Windows Server 2008 DHCP to supply unique subnet to a remote site?

  - by caleban

  The Main site hosts the only Windows Server. Windows Server 2008 R2 Domain Controller running AD, DNS, DHCP, Exchange 2007. Remote site has no Windows server. Main site subnet is 192.168.1.0/24 Remote site subnet is 192.168.2.0/24 The Windows Server at Main site is supplying 192.168.1.0/24 via DHCP to hosts at the local site where it resides. Is it possible to configure that Windows Server to supply 192.168.2.0/24 to hosts at the Remote site and if so how? We could use the Cisco router at the Remote site to supply DHCP but if possible we'd like to use the Windows Server at the Main site to supply DHCP.

  Read the article

• Laptops trying to connect via wireless? Only able to connect only via wired connection

  - by Chris J. Lee

  It seems that all the wireless laptops in the office have disconnected and are unable to reconnect to the wifi after a terrible storm caused some power interruptions. Troubleshooting actions Verify wireless broadcasting is up With each laptop i ended up flushing their dns cache on Win 7 (ipconfig /flush ) Performed an ipconfig /all to see what the new ip is Made sure password was correct Reset the router (multiple times) restarted each laptop. Tried connecting wirelessly Am i missing some small detail ? Network information The router is a linksys/cisco WRVS4400N router. Supports a lot of fancy features i don't know how to use. We have 3 static ip's the conference room computer, the wireless printer, my computer Mostly windows machines, we have 3 mac users

  Read the article

• A design for watching IPTV anywhere in the house?

  - by Carlos

  I'm currently getting TV and internet via IP to my house. The service comes into an ISP-supplied Router (ST585) which is in turn connected to an IPTV box. I need to replace the router, as it's port forwarding seems to be broken, so I was thinking of getting a box with an IGMP proxy. I once mistakenly got a non-IGMP box, with the result that the internet worked, but the IPTV didn't. The trouble is, I have no idea how to set up the IPTV part of the installation. I do have a copy of the ST585 configuration, but it doesn't look anything like the Cisco stuff that I learned about at CCNA. What are the steps necessary to reproduce the IGMP setup? I was thinking of WireSharking the communications on the network, but I suppose I'd need a hub for that? As a bonus, since the packets are coming in with the TV signal, is it possible to mess with the IGMP setup so I can watch TV anywhere in the house?

  Read the article

• A design for watching IPTV anywhere in the house?

  - by Carlos

  I'm currently getting TV and internet via IP to my house. The service comes into an ISP-supplied Router (ST585) which is in turn connected to an IPTV box. I need to replace the router, as it's port forwarding seems to be broken, so I was thinking of getting a box with an IGMP proxy. I once mistakenly got a non-IGMP box, with the result that the internet worked, but the IPTV didn't. The trouble is, I have no idea how to set up the IPTV part of the installation. I do have a copy of the ST585 configuration, but it doesn't look anything like the Cisco stuff that I learned about at CCNA. What are the steps necessary to reproduce the IGMP setup? I was thinking of WireSharking the communications on the network, but I suppose I'd need a hub for that? As a bonus, since the packets are coming in with the TV signal, is it possible to mess with the IGMP setup so I can watch TV anywhere in the house?

  Read the article

• Windows RRAS multi-network routing

  - by Brent Pabst

  I am looking for advice, comments and suggestions from anyone who has used Windows RRAS (2008 R2 Pref.) as the primary routers for our multiple offices. We have multiple physical office locations and are looking into utilizing Windows Server 2008 R2 Core as redundant Active/Active routers/gateways for our network as opposed to a physical router from Cisco or Juniper, it costs a lot less! Any problems, issues or documentation anyone would recommend? We will still most likely have a firewall on the edge but the majority of our traffic will be inter-office with some external services. We will be using multiple Class B networks across our two offices.

  Read the article

• Connecting via ShrewSoft VPN client means no LAN internet access (Windows 7 64 bit) - any advice please?

  - by iwishiknewmoreaboutnetworking

  I have a Windows 7 64 bit desktop machine which is connected to a LAN. I recently installed ShrewSoft VPN client v 2.1.7 on my machine so that I can connect to a license server hosted by my customer. They are running a Cisco VPN server and I originally tried (unsuccessfully!) to use the Cisco VPN client for Windows 64 bit but the default gateway wasn't being configured correctly after loading in my pcf file. Using ShrewSoft I am able to import the same pcf file, and successfully connect to the machine I need to using the VPN client software. The client machine I need to connect to has IP address 1.52.90.33. The problem is that when I am connected to the customer network using the VPN client application (and after a few minutes) I lose my LAN internet connection. I can only presume that this is because, by default the ShrewSoft VPN client application automatically tunnels all traffic through the VPN connection. I know there is an option to switch off the "Tunnel All" option on the Policy tab of the application and enter a Remote Network Resource (to "Include" or "Exclude") as "Address" and "Netmask" IP addresses however I am not sure what I need to enter here. Here is my ipconfig output before connecting to the VPN (with suffixes blanked out): Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : ***.*** Link-local IPv6 Address . . . . . : fe80::8de3:9dbe:393a:33ba%11 IPv4 Address. . . . . . . . . . . : 150.237.13.17 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 150.237.13.1 Tunnel adapter 6TO4 Adapter: Connection-specific DNS Suffix . : ***.*** IPv6 Address. . . . . . . . . . . : 2002:96ed:d11::96ed:d11 Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 9: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:2cf9:38c4:6912:f2ee Link-local IPv6 Address . . . . . : fe80::2cf9:38c4:6912:f2ee%12 Default Gateway . . . . . . . . . : Tunnel adapter isatap.***.***: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ***.*** Here is my route print output before connecting to the VPN: =========================================================================== Interface List 11...20 cf 30 9d ec 2a ......Realtek RTL8168D/8111D Family PCI-E Gigabit Ethern et NIC (NDIS 6.20) 1...........................Software Loopback Interface 1 14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter 12...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 150.237.13.1 150.237.13.17 2 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 150.237.13.0 255.255.255.0 On-link 150.237.13.17 257 150.237.13.17 255.255.255.255 On-link 150.237.13.17 257 150.237.13.255 255.255.255.255 On-link 150.237.13.17 257 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 150.237.13.17 257 255.255.255.255 255.255.255.255 On-link 12

  Read the article

• Is there a way to automate testing for a GNS3 network topology?

  - by Chedy2149

  I'm working on an MPLS backbone topology using GNS3, this topology includes configuration of several networking technologies such as IPv6, BGP, OSPF, IPv6 to IPv4 dynamic tunneling, MPLS based VPNs, MPLS based traffic engineering... So I'm a beginner with basic knowledge in networking (Ipv4 addressing, basic routing and switching) and I can't just easly test if my topology works or not, moreover fiddling with configuration I've noticed that sometimes when getting MPLS config right and missing BGP config all my topology is messed up. Given that I use Cisco 7200 series routers, is there any way to build a test harness for my topology in order to guarentee correctness with a single push button automated process?

  Read the article

• two identical broadband lines working as one

  - by Katafalkas

  I have been trying to find an answer to this, but all I get is hobbyists trying to connect they linksys's and get some magic out of it. So I am thinking of a way I could combine two 100Mbp Fiber Optics lines into a single connection for our office. I assume it involves some CISCO learning or something like this. Was thinking that I might need to configure some big router to load-balance the NAT'ing in some way. I assume that meny of you have done something similar and maybe someone could share the knowledge or at least provide some tips ?

  Read the article

• Multiple subnets behind SonicWall TZ 180

  - by Derek

  We have a SonicWall TZ180 that acts as a VPN endpoint. Right now it has one WAN IP address and a /24 assigned to the LAN interface. Our mail cluster administrator asked if it was possible to add a second private class C behind the VPN. This second subnet would be available to the other network and then we would use address objects and acls to limit access. Is this possible? I read up on PortShield but I don't know if that's what we would need to use because we're pushing all data out of one physical port into a Cisco switch that has VLANs already set up. Addendum: It appears that PortShields will do what I want with only one limitation; it requires a direct 1-1 relationship of portshield to physical port. This would then limit us to 4 PortShields on 1 TZ180. Is there a better solution than this?

  Read the article

• Data transfer speed to USB storage connected to wifi router very slow

  - by RonakG

  Here is my setup. A Linksys Cisco E3200 wifi router. A MacbookPro running OS X Lion 10.7.4. A Seagate GoFlex 1TB hard drive connected to wifi router via the USB port. When I try to transfer data from my MBP to the HDD, the data transfer rate is very low. I'm getting around 3MB/s write speed. This is very slow compared to the speed I get when HDD is directly connected to the MBP. The HDD is NTFS formatted. And the router provides access to HDD using Samba share. So I connect to the HDD using smb://. What is the limiting factor here affecting the data transfer rate?

  Read the article

< Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >