Search Results

Search found 11747 results on 470 pages for 'music manager'.

Page 400/470 | < Previous Page | 396 397 398 399 400 401 402 403 404 405 406 407  | Next Page >

• 5.1 Surround Channels are Jumbled

  - by stickynips

  I had this exact setup working previously, but after a reformat it went screwy on me. I have an Onkyo A/V Receiver hooked up to my PC, via optical S/PDIF. Attached to the receiver is a 5.1 speaker setup (tested and working fine with my Xbox via the receiver). It seems to me that the audio channels are getting mixed up somehow between the PC and the receiver. I have a 5.1 test file which plays a sounds through each speaker individually. The channels are mixed as such: "Left Front" plays through my Right Front speaker "Center" plays through my Left Front speaker "Right Front" plays through my Center speaker "Left Rear" plays through my Subwoofer "Right Rear" plays through my Left Rear speaker I've tried downloading the latest Realtek HD Audio Drivers and the Realtek HD Audio Manager, but neither makes any difference. If there's a way I can manually rearrange the channels I believe it would fix the problem, but as far as I know this is impossible. edit: Sorry, I've forgotten some basic info. I'm running Windows 7 x64. The sound card is Realtek ALC892 embedded in a GIGABYTE GA-890GPA-UD3H AM3 motherboard.

  Read the article

• Can't start Windows 7 after cloning HDD

  - by Paul

  Brief description: cloned HDD1 - HDD2 HDD1 partition 1 boots HDD1 partition 2 boots HDD2 partition 1 boots HDD2 partition 2 doesn't boot Windows, but is bootable in general Now verbosely: In all the cases computer is the same. I have two Windows 7 installations on HDD1 - both are booting fine. I choose between them using standard Windows 7 boot loader menu. Technically there are 4 partitions: 100 MB Boot loader partition (active), Windows 7 copy 1 (25 GB), Windows 7 copy 2 (150 GB) and Working partition. All are primary. In past few days I tried to clone the whole HDD1 to HDD2 of the same size (but 2,5 inch form factor) as is using Minitool Partition wizard. Everything has been copied, all files are accessible, no faults in file system structure, even boot loader wasn't damaged and I hadn't to repair it. But I can boot only first installation of Windows 7 (it boots without issues). When I choose the second installation, I get immediately a completely black screen without any texts, cursors and other data. HDD isn't accessed after that. This black screen is sensitive to Ctrl-Alt-Delete which causes computer reboot. I did some experimenting: Installed Windows 7 to that partition - it booted fine. Then I renamed "Windows" to "Windows.old" and copied Windows directory from HDD1 as it was, using Far Manager, and got the same troubles - black screen. (Of course I performed renaming and copying from other copy of Windows). So, it seems that problems are inside this installation of Windows, somewhere in its files.

  Read the article

• Wake-on-lan only works so many times

  - by Chance

  I have Wake-on-lan configured on my Windows XP machine so that the computer will wake up from Standby. Waking the computer from Standby via network traffic seems to work a certain number of times, say 4 or 5, then it stops working. If I restart the computer it seems to reset this behavior so that I can use WOL a few more times before it starts working. I use the command "wol" on my other, Linux machine with the appropriate IP address and MAC address of the card. I looked at the network card to see if it had different lights when WOL worked and when it didn't. When it has a solid amber light where the ethernet cable connects, WOL seems to work. When it has a flashing amber light, WOL does not. It seems that the system seems to almost "shut off" the card when it falls to sleep, but I don't know if this is a function of time or number of standby/wakeups. I have a 3Com 3c920 network card. If I look at the properties in Device Manager, I have "Allow this Device to bring the Computer out of Standby" checked. In the Advanced tab I have anything related to RWU (Remote Wake Up) enabled. I also believe I have the appropriate settings in BIOS related to Remote Wake-Up and I have tried both S1 and S3 power configurations in the BIOS. Intuitively, I would think I would uncheck "Allow the Computer to turn off this device to save power", but doing so disables the "Allow this Device to bring the Computer out of Standby" option. Does anyone know what is happening here or if there is a way to fix it? I have an integrated network card; would getting one that goes into a slot be better? I am running Windows XP on a Dell Optiplex GX240 with a 3Com 3c920 network card.

  Read the article

• Reducing both pagfile.sys and hiberfil.sys in Windows 7

  - by greenber

  I recently used Defraggler to consolidate my free space areas on my D: drive preparatory to using Disk Manager to break my drive into two areas, one as my "data area" for Windows 7 (normally on my C: drive) and to experiment around with Windows 8. The Defraggler program works so well I ran it on my C: drive and I ended up with a lot of free space both on my C: drive and my D: drive. I was very happy. And then I woke up the next day and I've got virtually no free space left, something like 8 MB on my C: drive and about 3 GB on my D: drive. I then ran Wintree (which gives a nifty graphical representation of disk usage) and found I had a large page file and a large hiberfil. So I temporarily turned off hibernate and reduced the page file size to 2000megabytes and then rebooted so that both would take effect. It had no effect on the C: drive or the D: drive. That makes no sense to me. What caused the free space on each drive to disappear, why doesn't the page file size being reduced and the hibernate file being turned off free up disk space to either the C: or the D: drive? Would it make sense to delete the two files in question and, if so, how do I go about doing that? Safe mode? Thanks. Ross

  Read the article

• MS Excel and Access - which is better for reports?

  - by Nat

  Where I work, staff have just started to use a basic table in excel (1 october) to record sales which has about 10 columns (name, client, renewed, discount, paid etc). I record the data (total sold etc) every hour and email it to the manager. Each staff has the their own file on the network which they use constantly for that day (eg. John 08-10.xlsx; John 09-10.xlsx etc) and have been told to save the file after they complete a row with client data. I can see the file (in read only mode) to update the report but I am sure there must be a way of doing an autoupdate of their worksheets in real time. I can link worksheets and workbooks to my main workbook but manually. Does anyone have suggestions on have to do this on Excel? Or would Access allow me to make a report which shows the sales total for that hour without the staff closing the file or constantly clicking save every few minutes? We use office 2010. thanks

  Read the article

• Configuring a MySQL 5.1 Instance on Windows 7 Professional x64 Fails

  - by Thomas Owens

  I'm trying to set up my laptops to function as mobile development environments. Installing the software on my Linux machine and getting it configured was fairly straightforward, however I'm having trouble getting MySQL 5.1 Server installed and configured on Windows 7 Professional 64-bit. I'm currently using the Windows MSI Installer for the complete MySQL 5.1 system (as opposed to the Essentials installer also available). I've tried to install using both the 32-bit and 64-bit versions of MySQL 5.1 - the same events occur in both. I've installed both the Server Instance Configuration Wizard and Workbench and everything appears to be installed just fine. When I open the Instance Configuration Wizard, I select Detailed Configuration. On the next screen, I select Development Environment, then Multifunctional Database on the next screen. I leave the InnoDB settings unchanged. I select Manual Setting with 5 concurrent connections. I enable TCP/IP Networking on Port 3306 and Enable Strict Mode. I select the Standard Character Set. I check the boxes for Install as a Windows Service (and provide the name "MySQL") and Include the Bin Directory in Windows PATH. On the next screen, I set my root user name and password. I do not enable root access from remote machines and I also do not create an anonymous account. On the final screen of the wizard, when I click "Execute", the first two tasks (Prepare Configuration and Write Configuration File) complete. However, when it reaches Start Service, the wizard hangs and becomes unresponsive ("Not Responding" appears in the title bar and Task Manager). I would really like to be able to use both my Windows and Linux laptops as full-blown mobile development environments, but I can't do that without being able to run MySQL. Has anyone encountered this problem before? What options do I have to correct it?

  Read the article

• IIS 7, FastCGI, PHP and custom php.ini files

  - by Marlon

  I'm running PHP 5.3, FastCGI, and IIS 7 on Windows Server 2008. I have a site which I would like to configure its own php.ini settings for but things aren't working as expected. I am following the tutorial located here. This is what I have done so far: 1) Configured a new website with it's own AppPool. 2) Selected PHP 5.3.6 from the PHP Manager available on the website home on IIS (not the web server home which sets the global version of PHP) 3) Added the following lines to the section of the applicationHost.config file located at system32/inetsrv/config <application fullPath="C:\Program Files (x86)\PHP\v5.3\php-cgi.exe" arguments="-d open_basedir=C:\inetpub\wwwroot\kickasswebsite.com" maxInstances="4" idleTimeout="300" activityTimeout="30" requestTimeout="90" instanceMaxRequests="200" protocol="NamedPipe" queueLength="1000" flushNamedPipe="false" rapidFailsPerMinute="10"> <environmentVariables> <environmentVariable name="PHPRC" value="c:\inetpub\wwwroot\kickasswebsite.com" /> </environmentVariables> </application> 4) I then create a php.ini file located in C:\inetpub\wwwroot\kickasswebsite.com (the location of the root of the website) register_globals = on 5) I then run test.php which simply outputs everything the method call to phpinfo() returns. At this point, I observe that the global setting for register_globals = off (as it should be), but the local setting for register_globals = off, even though I specified it differently in the php.ini file I created at the root of the site. Furthermore, I see these settings in the output of the php.ini Configuration File (php.ini) Path C:\Windows Loaded Configuration File C:\Program Files (x86)\PHP\v5.3\php.ini Scan this dir for additional .ini files (none) Additional .ini files parsed (none) What am I messing up on, or is there a different way to go about this?

  Read the article

• VMM 2012 Adding Hosts in Trusted Forest

  - by Steve Evans

  I have two forests with a two way trust between them. VMM 2012 sits in ForestA and I can discover hosts in ForestA with no issue. When I try to discover hosts in ForestB I hit one of two issues: If I go through the GUI or use Powershell just like I normally do I get the following error on the job: Error (10407) Virtual Machine Manager could not query Active Directory Domain Services. Recommended Action Verify that the domain name and the credentials, if provided, are correct and then try the operation again. It doesn't matter which account I use. I've tried accounts from both forests, with Admin/Domain Admin permissions all over the place, etc Going through the GUI (can't find the switch in Powershell to duplicate this), I check the box "Skip AD Verification" and it causes the GUI to crash during discovery. I found an article (http://technet.microsoft.com/en-us/library/gg610641.aspx) that describes how to add a host in a disjoint namespace (even though that doesn't apply to me) and it says that VMM creates an SPN if one does not exist. So I verified that the correct SPN's exist in ForestB, that did not help the issue. I have a case open with PSS but they are stuck. I have VMM traces if anyone would like to see them. Any suggestions or ideas?

  Read the article

• How to set umask globally?

  - by DevSolar

  I am using a private user group setup, i.e. a user foo's home directory is owned by foo:foo, not foo:users. For this to work, I need to set the umask to 002 globally. After a quick grep -RIi umask /etc/*, it seemed for a moment that modifying the UMASK entry in /etc/login.defs should do the trick. It does, too -- but only for console logins. If I log in to my desktop, and open a terminal there, I still get to see the default umask 022. Same goes for files created from apps started through the menu. Apparently, the display manager (or whatever X11 component responsible) does source some different setting than a console login does, and damned if I could tell which one it is. (I tried changing the setting in /etc/init.d/rc, and no, it did not help.) How / where do I set umask globally (and for all users), so that the X11 desktop environment gets the memo as well? (The system is Linux Mint / Ubuntu, in case that changes anything...)

  Read the article

• Hard Drive that was used before not detected or accessible in Windows 7

  - by Anders

  Hello SU: My PC crashed for some unknown reason, and I am still working on what caused that. However, I pulled my main (windows) drive from my computer and hooked it up to my roommate's machine and was able to pull the data I needed off of it (i.e. the drive is good). I hook up his drives as they were, I had to turn off his machine and unplug his secondary drive to hook mine up, boot his machine and there is no second drive available in windows explorer. I opened Device Manager to see if for some reason it's drive letter got un-assigned, but there is nothing listed in there except his primary hard drive, his optical drive and one other optical drive which I believe is the virtual drive Daemon Tools made. The drive shows up in the BIOS, however after I restarted his machine again it sits on the "Entering setup....." screen at the load window. The only thing I can think of is that may have messed with stuff is I used this tutorial to create a bootable XP install on a USB drive to install XP on my machine (I am 99% certain that the optical drive in my PC is broken) and maybe it used the other hard drive's letter for the USB drive for some reason, which doesn't make much sense since it was recognized it as a different drive letter before I started the process. It is possible that it used the secondary hard drive's letter for it's work, but once again I am uncertain. Where should I go from here? He his bound to wake up within the next several hours and will probably flip a lid if I cannot get some sort of handle on this. Any and all help is greatly appreciated. PS: Anyone who helps me get this situated has a beer or two on me, as long as you are in the greater metro Detroit area, or don't mind traveling a bit!

  Read the article

• Weird problem with Visual C++ 2010 Express

  - by Robert Vella

  This has happened before on my Vista Premium installation, and now it's happening on my Windows 7 Home Premium installation. Basically everytime I install Visual Studio Express 2010, it works fine for a random amount of time but then suddenly starts to hide from my sight -- that's the best way I can explain it. VS does not crash, and from what I can tell it does not freeze either; It continues to work, I can even "minimize" and "maximize" it; I simply cannot see it nor can I interact with it any meaningful way. Also: After the "crash" there are no logs in: Root\Program Files (x86)\Microsoft Visual Studio 10.0\Microsoft Visual C++ 2010 Express - ENU. Nor any other files created at the time of the crash. There are no traces in the event viewer. The program seems to be functioning perfectly in the process manager. If I reinstall Visual C++, it works normally for a seemingly random period of time before going cookoo again. I am stumped. This has never happened to me before, with any other program. And yet I doubt it really is a problem with Visual C++; More like something general that seems to have picked on it for some reason. Still, after a clean install with a new OS, I'm kinda thinking there's something wrong here. Any help would be appreciated, altough I suspect that the answer to this question will make me feel embarassed. P.S. Not sure if it helps, but I think around the same time I started having problems (On both installations) with windows turning off the display when I leave the computer, and then seemingly crashing when it turns it on again -- in fact when I interact with it it seems to be responding to my commands without actually display anything.

  Read the article

• HP EliteBook 8440P - USB ports stop working on docking station

  - by r0ca

  I have a HP Elitebook 8440P running Windows XP Pro SP3. I installed it on my docking station and everything went smooth for a while. Last week, my mouse and any other USB devices stoped working sudenly... It was working fine on my laptop itself but nothing on my docking station. LCD attached monitor works and same for LAN and PS2 keyboard. I updated the BIOS, Chipset, Video Drivers, also changed my docking station by a brand new one but the problem still comes back. I also noticed something in Device Manager... A Generic USB Root Hub has an error on it, a Yellow/Orange exclamation mark. I tried to update that driver but no luck. Windows is unable to process it. This seems to be the problem but can't fix it. I may only re-image my laptop but for me, I need to avoid that since I have so many apps installed on it. If anybody has any advice, I'll take it!

  Read the article

• Windows 7 hangs on black screen for a while after log in

  - by steini

  I get the welcome screen. I click on my user and get the "logging on" screen. After that all I get is a black screen with a mouse cursor. I can't even start task manager. No ctrl+alt+del or ctrl+shift+escape. It stays like this for about 10 minutes, then the desktop finally starts loading. According to the hdd led on my case, windows isn't even trying to access the hard drive for that whole time. It's just hanging doing nothing it seems. What I have tried: Uninstalled video driver and removed leftovers with driver sweeper Disabled all startup programs and non microsoft services Loaded "last known good configuration" Ran the alleged "black screen fix" from prevx against my best judgement (don't really like running random exes without knowing what they do at all) None of that works. I can boot into safe mode normally. My specs: i7 920 Gigabyte X58-UD3R Gigabyte HD5870 1GB 12GB Mushkin Silverline 1333MHz Windows 7 Ultimate x64 I'm also having another problem which I suspect is related. After I have gotten the computer up and running, everything works perfectly, but when it's been on for a while it starts behaving strangely when changing display modes. When I start up a game or anything that changes the screen resolution the computer freezes for about a minute every time until I reboot again. I think this is probably related to the black screen problem. Just thought I'd check to see if anyone has had the same problem. Let me know if I should post any more details about my system to help diagnose this. Thanks in advance.

  Read the article

• BIOS and Windows cannot detect CDROM device

  - by eman

  Hello! I have a HL-DT-ST RW/DVD GCC-4521B dvdrom device and a big problem. Some days ago everything worked fine. A friend installed some software and then the drives in winxp has been marked as corrupt. I uninstalled the software, but still corrupt drives. The next step I have done was running the current software GCC-4521B101(E).exe. When I ran this software again, the drives was automatically updated, but still marked as corrupt (in the Device Manager), even if I did a reboot. And then the big mistake: once more I tried to run this software, but during the update process, the machine restarted and boom! The DVDROM device doesn't work anymore. The led doesn't blink and if I push the eject button, nothing happens. Also bios and winxp doesn't recognize the optical drive. Then I plugged an other optical drive and it worked, but my old drive seems to be dead. So, what happened and how to solve this problem? Please help. Regards!

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

  Read the article

• Unable to sync iPod Touch with my PC

  - by alex

  I'm trying to sync a first gen iPod Touch to my PC running Windows 7 64 bit. The problem is that whenever I connect the iPod, iTunes completely freezes (if I start iTunes after connecting the iPod it will simply hang until it's physically disconnected from the PC). I reinstalled iTunes thinking that it had been corrupted, but without any luck. I've had this problem with all the latest versions of iTunes. I've also tried using MediaMonkey and DoubleTwist. None of these apps see the iPod as being connected; DoubleTwist also freezes, just like iTunes. The really strange thing is that I was able to sync the iPod with this PC a while back, but I now seem to have lost that ability. I don't know what changed. Windows detects the device every time it's plugged in (I can see it in Device Manager and I can browse all photos on iPod as if it were a camera). Also, I can sync it to iTunes on Mac OS X without any major problems.

  Read the article

• Reliable backup software for windows network/samba shares.

  - by Eli

  Hi All, I have a Win2003 server that works as a pdc for a number of XP boxes, and a couple related FreeBSD boxes. I need to back up roaming profiles, non-roaming profiles via network shares, local hard drive data, and files on the FreeBSD boxes via samba shares. I have tried Genie Backup Manager and Backup4All pro, and both have excellent features, but both also begin to fail disastrously with more than a few days use. Mostly, the errors seem to have been from the backup catalog getting out of synch with itself. Whatever it is, there is no excuse for a backup software that says it backed up files when it really didn't, or the log saying it backed up exactly the same file 10,000 times in a single run, or flat-out crashing, or any of the other myriad problems I've run into with these. Really sad for products that fill such an important need. Anyway, does anyone know of a backup software that works reliably and can do the following? Scheduled backups for multiple jobs, without a user logged in. Backup from local hard drives or network shares. Incremental backups. Thanks! Edit: Selected solution: I've added my (hopefully final) solution as an answer.

  Read the article

• All of the NTFS hard links disappear, where are hardlinks stored on disk and how to recover them?

  - by Osiris

  This is Windows 7 x64 sp1 on a NTFS file system. All hardlinks within C:\Windows\System32 folder disappear, and the Windows can't boot, because even the osloader, C:\Windows\System32\boot\Winload.exe also disappeared. Nevertheless, the original files are still located in the corresponding C:\Windows\winsxs folders. After booting into the Recovery Environment, and copied one Winload.exe (x64) from other folder, Windows gave an error pointing out that "ntoskrnl.exe is corrupted or missing...its file digital signature cannot be verified" In trying to boot in Safe Mode, the message above was shown after a screen prompting "Loaded \Windows\system32\config\system" Because at this early booting stage, smss.exe was still not loaded, so there is not any dumping and logs. Based on my study, ntoskrnl.exe depends on the following files: C:\\windows\\system32\\PSHED.DLL C:\\Windows\\System32\\hal.dll C:\\Windows\\System32\\kdcom.dll C:\\Windows\\System32\\clfs.sys C:\\Windows\\System32\\ci.dll All those files above are copied from their corresponding folders and verified their md5 with a well-operating Windows 7 x64 SP1. But the booting error is still the same: "ntoskrnl.exe is corrupted or missing..." **Background:** Before the reboot, there was an windows update going on. Then something unknown happen, almost all processes were broken to run, including the windows task manager, taskmgr.exe. After mount the hard disk to other computer, it seems that all hardlinks within C:\Windows\System32 folder were gone. I tried several data recovery software, but they are not be able to find those disappeared NTFS hard links. So the question is: Where are information about those hard links stored? And how to recover them? Are they depend on some windows service or stored in the registry?

  Read the article

• Win 8.1 Hyper-v Full Screen and VPN problems

  - by tr0users

  I need to connect to my office using Cisco VPN software (RSA). Once connected all my internet traffic goes through the employer's VPN and this prevents me from listening to spotify. As a way around this I created a Win 2012 VM that I run in hyper-v from my Windows 8.1 Client. First I RDP to the VM, then I connect to the VPN. This forces the RDP session between my host laptop and the VM to close. I then open the hyper-v manager and double-click my VM to get a connection back (not great because I don't get the use of copy & paste this way). Previously when I opened my VM this way I would have full screen. I'm using a 1920x1080 monitor. Today when I re-open my connection to the VM it is displayed in a window that uses maybe 75% of the full screen. I have tried the menu option View\Full Screen Mode only centres the screen and apply black borders around the outside. Could anyone please suggest how I may solve the VPN or Full Screen problems? Thanks Rob.

  Read the article

• How can I make grub2 boot into Windows 7?

  - by Grzenio

  I had Windows 7 installed on my system, then I installed Debian testing with grub2 as its boot manager. Initially I couldn't see windows entry in grub at all, so I ran: aptitude install os-prober kcpuload update-grub Now I can see the entry, but when I select it I get only Win7 system restore, instead of the the real thing. Any ides how to make it work? EDIT: I tried the suggested approach to add a new file to /etc/grub.d, which generated an entry in grub.cfg, but it does not appear in the grub menu on boot :( I have this: grzes:/home/ga# cat /etc/grub.d/11_Windows #! /bin/sh -e echo Adding Windows >&2 cat << EOF menuentry “Windows 7? { set root=(hd0,2) chainloader +1 } And I have the following grub.cfg file: grzes:/home/ga# cat /boot/grub/grub.cfg # # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then load_env fi set default="0" if [ ${prev_saved_entry} ]; then set saved_entry=${prev_saved_entry} save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z ${boot_once} ]; then saved_entry=${chosen} save_env saved_entry fi } insmod ext2 set root=(hd0,3) search --no-floppy --fs-uuid --set 6ce3ff31-0ef7-41df-a6f5-b6b886db3a94 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi set locale_dir=/boot/grub/locale set lang=en insmod gettext set timeout=5 ### END /etc/grub.d/00_header ###

  Read the article

• Replacing HD in an MacOS 10.6.8 server caused all shares to fail

  - by Cheesus

  I'm hoping someone might have a helpful suggestion about this problem. We have 2 MacOSX servers available for file sharing. (quad Xeons - 2GB RAM, both 10.6.8), No.1 is an Open Directory Master with 50+ user accounts, No.2 has only 2 local accounts (/local/Default) and looks at the OD Master for all user accounts (/LDAPv3/10.x.x.20/) Both servers have 3 internal HD's, The boot volume with only Server OS and minimal Apps. A 'DataShare' HD (500GB) and a backup drive (500GB). After upgrading the DataShare HD in Server No.2 from a small internal HD (500GB) to larger capacity (2TB) drive, users are unable to connect to shares on Server No.2. Users get an error "There are no shares available or you are not allowed to access them on the server" The process I followed was to use Carbon Copy Cloner to create an exact copy of the original data drive (keeps all ownership data, UID, permissions, last edit date and time). Everything booted up ok, no indication there was any issues. (Paths to the sharepoint look good) Notes during troubleshooting - Server1 is operating perfectly, all users can access shares and authenticate etc. - I've checked the SACL (Server Access Control List) settings is ok. - On Server2 in the Server Admin' app, I can see all the shares listed ok. The paths seem valid, I can disable / reenable the shares, no errors. - On Server2 'workgroup manager' lists all the accounts from the OD Master in the LDAP dir view. All seems fine from here. Basically everything looks normal but no file shares on Server2 can be accessed from regular users.

  Read the article

• High memory utilization with firebird + windows server 2008 r2

  - by chesterman

  i have a Windows Server 2008 R2 (64bit) running a 64bit installation of Firebird 2.1.4.18393_0 in a 4GB phisical server. After a while, the task manager show that all memory is used, but the sum of the memory of all process does not stack to the half of the memory. Unfortunally, it's start swapping. Using RAMMAP, i can see that my entire database file is mapped into the memory. This only occours in windows server 2008 r2 and windows 7 64 bit. i can use firebird 32 or 64bit installations, doesn't matter. How can i prevent this? Why this only occours in w2k8r2 and w7? tks in advance ** UPDATE Aparently, this occours by the use of all memory by the file system cache. The microsoft documentations explain that this WAS a issue in windows xp, 2k3, vista and 2k8, but it was solved in 7 and 2k8r2. also adds that this issue is more common in 64bit hosts. (http://support.microsoft.com/kb/976618) there are some tools (DynCache, setcache and the Get/SetSystemFileCacheSize system calls from windows API) that allows me to fix a upper limit to the memory usage by the fscache, but the documentation argues that i should not do this in w2k8r2 because it will severely impact on the overall system performance. anyway, i tried, the performance remained the same shit and the use of the page file remained, although there is now more the 1gb of free memory.

  Read the article

• SQL Server Installation: Is it 32 or 64 bit?

  - by CapBBeard

  Hi, Recently I was performing an OS upgrade on one of our DB servers, moving from Server 2003 to Server 2008. The DBMS is SQL Server 2005. While reinstalling SQL on the new Windows installation, I went to another of our DB servers to verify a couple of settings. Now, I always thought this second server was Server 2003 x64 + SQL 2005 x64 (from what I'd been told), but I now have my doubts about this. I now suspect that it is in fact only 32 bit SQL, however I'd like to verify this. Here's some details: The OS is definitely 64 bit. xp_msver shows Platform as NT INTEL X86 SELECT @@VERSION shows Microsoft SQL Server 2005 - 9.00.4035.00 (Intel X86)... However sqlservr.exe is not shown with '* 32' in taskmgr, does anyone know why this is the case, if it is in fact 32 bit as claimed? Despite this, it does seem to be running out of the x86 program files folder. If I do the same checks on a confirmed 64 bit installation, it does give back the expected 64 bit readings, which can only prove that this server in question is only running in 32 bit. Now, that being the case, the question arises about how much memory this '32 bit' install can use. Task manager reports about 3.5GB memory usage for sqlservr.exe (The server has 16GB physical). I suspect that AWE has not been configured at all, and therefore the server will be significantly under-utilised (remembering that the OS is 64 bit) if SQL is simply using a 32bit address space. Is this assumption correct? I feel the server should have SQL reinstalled as 64 bit in order to fully utilise the hardware platform, however it is currently heavily in production; this will be no easy task. I suspect we may just have to configure AWE correctly and let it be for the time being (Unless this is a bad idea?). I apologise that this question is a little vague/lost; I'm no SQL expert, just trying to get a handle on what's going on here.

  Read the article

• HP dv6910 laptop no longer recognizes wireless adapter, dvd drive, and one usb port. What can I do about this?

  - by Joan H.

  In the last 3 weeks, my not even 3 year old HP laptop (vista) just seems to be failing. First, one of the usb ports stopped working. Next, the dvd drive all of a sudden was not recognized as even existing, so it is now useless. And as of today, I no longer seem to have a wireless adapter on my laptop. It doesn't show up in device manager, same as the dvd drive. I can connect to the internet by ethernet cable, but not wirelessly. It worked fine last night; now it doesn't even exist! I have tried a 'hard reset' I read about on HP's forum- no help. I am not sure what else to try. I read about the USB wifi dongle in another response, but I already have maxed our my usb ports even though I have bought a USB hub since the one port failed. Plus, I'd like my laptop to just work like it's supposed to instead of being jerry rigged with usb hubs, external dvd drives, and wifi dongles etc. Any ideas?

  Read the article

• Why does Windows/Microsoft Updates always take such a long time to detect available updates?

  - by RLH

  It's a common task for many of us who work in any form of IT position using Windows. Eventually you have to install/re-install a version of Windows and what follows is a very long OS updating process. For a long time I have accepted the fact that this is a slow process and that's all there is to it. There is a lot to download, and some updates require restarts followed by further updates... Ugh! This morning I had to go through the process of installing Windows XP with SP3. I'm installing the OS on a VM on an SSD and I've been working on this thing for over 6 hours. Although, think there are many ways to knit-pick this process for improvements, there is one step that is always particularly slow and I can not figure out a good reason why. That step is the detection step on a manual update. Specifically, when navigate to the Windows (or Microsoft) Updates page, and then click the 'Custom' button to detect your updates. It appears that your PC just sits there for a painful amount of time. Check your Task Manager and it looks like your PC is, in fact, locked because your CPU isn't cooking but that's certainly not the case. Somethings happening but I have no clue what's going on? What is the updating software doing? If the registry was being searched, shouldn't my CPU usage peak? Does anybody know what's happening? I can loosely justify why some of the steps in the update process take so long. However, this one doesn't seem to have any reasoning.

  Read the article

< Previous Page | 396 397 398 399 400 401 402 403 404 405 406 407  | Next Page >