Search Results

Search found 13293 results on 532 pages for 'small ticket'.

Page 400/532 | < Previous Page | 396 397 398 399 400 401 402 403 404 405 406 407  | Next Page >

• What are the replacement options for an IDE hd for a DOS based system?

  - by dummzeuch

  I have got a few "embedded" systems running MSDOS 6.2 which boot from and store data to IDE hard disks. Since these drives are nearing their end of life, the question arises how we can replace them. The requirements are: DOS must be able to install and boot from these drives. They must be able to sustain heavy (mostly) write access. If possible, they should be able to survive moderate vibrations (not too bad since the current hds have survived several years of that) I considered the following options so far: other ide hard drives: Unfortunately modern IDE drives are too large so DOS cannot boot from them even if I create small partitions. Older IDE drives are just that: old, so they are probably not the most reliable ones any more. SSDs: There are a few SSDs with IDE interface available. I have not yet tried them. Does anybody have any experience with them? They look like the ideal replacement provided that DOS can boot from them and that writing speed does not deteriorate too much (the old hds are no race cars either). Compact Flash: There are adapters for using CF with IDE controllers and they work fine. DOS can boot from them and they have no problems at all with vibrations. What I am not sure about is their durability. DOS uses FAT so some very few sectors are written every time the medium is being written to. IDE to SATA converters: I have no idea whether they are any good. Has anybody tried them? It might be an option to use one of these to connect an SATA SSD to the system. Are there any alternatives that I have missed? (We are working on replacing these systems, but it will still take a few years.)

  Read the article

• Network bandwidth usage dashboard?

  - by SkippyFlipjack

  I have a couple of wifi access points hooked up to my home network, one of which I keep unsecured for some development I do; there are only a couple other homes within range and they've got their own wifi so it's not a big concern. I also have a Sonos system, Tivo, Roku, a couple laptops, a couple phones, an iPad and a desktop machine, all of which are internet-smart. So when my internet bandwidth tanks and it takes five minutes to load a YouTube video, I want to know what's going on, and there are many potential culprits. I'd like to be able to plug my MacBook into the primary router and see a nice little dashboard of the units on the network and what kind of bandwidth each is using at that moment. I could figure this out from WireShark or tcpdump but figure there has to be an easier way. I've tried a few different commercial products but none really presented the right info. Suggestions? (This may be a question for superuser since my Apple Time Capsule's SNMP capabilities are limited, but I figure admins of small business networks would have dealt w/ the same issue..)

  Read the article

• What switch should we use for PCoIP?

  - by Jay R.

  We have a small lab space that seats 10 people and has 20 machines. Each machine is set to 1920x1200 resolution because the user apps are best used at that resolution. Currently the machines are all located close enough to montors that a DisplayPort cable will reach, but the pending lab remodel positions them around 80 feet or more away in racks. Our proposed solution is to use PCoIP. We purchased 10 PCoIP portals and 20 PCoIP host cards. We plan to set up a dedicated network to handle just the PCoIP traffic. After testing just one portal and one host card with a cheap 1G switch from a local office supply store, we were left with less than good impressions about the usefulness in our lab. The framerates were not spectacular and the mouse seemed jerky. Our concern is that we can't get away with the cheap 1G stuff from the store because adding more machines to the switch will just make the user experience worse. What switch would be recommended to best support our PCoIP situation? We will need to plug in at least 30 cables based on just those machines. Is there a particular feature to search for that makes a difference? Is there a switch that works best with PCoIP? Added Info: The reporting webapp for the host card shows maximum bandwidth usage to be 220000 kbps. The average appears to be around 180000 kbps. The reverse direction is much lower, like 15000 kbps.

  Read the article

• How to export and import an user profile from one Quassel core to another?

  - by Zertrin

  I have been using Quassel as my bouncer for IRC for quite a long time now. We (a group of administrators of a small network) have set up a shared Quassel core with many users on the same core. But now I would like to export everything related to my user account from the Quassel database on this core, in order to re-import it later in another Quassel core on my own server. Unfortunately, while a feature for adding users has been implemented into Quassel, nothing is so far provided for either exporting or deleting an user. (if deleting-a-user feature was available, I could have made a copy of the current database, delete all the other users leaving only mine, and use this resulting database on my own server, while leaving the first one untouched on the shared server) Despite extensive research on the Internet on this subject, I've found so far no solution. I have to precise that the backend database for the core has been migrated from the default SQLite backend to a PosgreSQL backend as the database grew sensibly (over 1,5 GB for now). However I'd be glad to hear from any working solution (SQLite or PostgreSQL backend) describing a way to export the data related to a specific user profile and then re-import-it in a new Quasselcore database.

  Read the article

• Nginx Redirect when URL includes variable p=1

  - by ChrisD

  Need to write a small nginx rewrite line(s) to alter/301 redirect some URLs within our existing website. for example: www.example.com.au/pageone.html?p=1 to www.example.com.au/pageone.html www.example.com.au/pagetwo.html?dir=asc&limit=200&order=price&p=1 to www.example.com.au/pagetwo.html?dir=asc&limit=200&order=price www.example.com.au/pagethree.html?dir=dsc&limit=100&order=price&p=1 to www.example.com.au/pagethree.html?dir=dsc&limit=100&order=price As you can see p=1 has been stripped from the URL's (as it is superfluous but has been live on the site and needs to be redirected now) - all http and https links. Basically if, and only if, p=1 is used anywhere within the URL then it should redirect to the same URL without the p=1. This should also let p=11, p=12 through as normal (and not redirect), as it is not specifically p=1. # # # # If that is not possible then, I'd like to know how to redirect this kind of URL as a standalone one off: www.example.com.au/pageone.html?p=1 to www.example.com.au/pageone.html I tried several redirects but they were all pointless and did not work, and was not able to get it working. To be honest I do not really know where to start with this - I am new to nginx.

  Read the article

• Buying an old laser printer -- what will need to be replaced?

  - by marienbad

  Hi all -- as you can see I'm new. I do IT and wiring for a small local shop but I never deal with printers. I do a LOT of printing, and I'd like to stop spending as much money on it. On my local CL, there is an HP 8100DN (duplex network) printer for a very good price (and the toner is a quarter-cent per page). It has printed 200,000 pages and I don't yet know anything else about it. The model was released in 1999. So my questions: What are the parts that tend to need service on laser printers? On ebay, I see fusers, rollers, DC power boards, and motors. What would you expect to replace soon at 200,000 pages? Are there any good "tests" to find out if certain parts are near failure? Do you have anything to say about the HP 8100 specifically? The bottom line for me is that if there's any chance of repairs costing more than $100, it's not worth it for me.

  Read the article

• sharing a USB printer in SOHO environment [migrated]

  - by Registered User

  Here is a situation I am facing, there is USB printer which works only on a Windows XP machine, there are other devices in LAN it is a Small Office Home Office environment. How can this USB printer attached to Windows XP machine be shared so that other laptops or users in Network who have Windows 7 or Linux on their laptops can use this printer. The printer model number is Canon Laser Shot LBP-1210 http://www.canon-europe.com/For_Home/Product_Finder/Printers/Laser/LaserShot_LBP1210/index.asp a print server is not available to me I need to make it work in this situation only.What can I do? the clients are unable to connect to this.It is not a network or TCP/IP printer If a from Windows 7 machine some one wants to use this printer so that he can take a print he gets an error while adding the printer to his machine which is a Windows 7 machine (where as the printer is USB printer on Windows XP machine) Start--->Devices and Printers---> Add Printer---> Find Printer by name or IP address--->Selected a shared printer by name-->\\PC-Name-printer3 and select browse it gives a message Windows can not find a driver for Canon LASER SHOT LBP-1210 on the network what does this mean do I need to install some kind of software at client machine or on the machine where printer is present?

  Read the article

• How to fix Windows 7 device removal notification loop

  - by Barry Kelly

  Bit of an odd one this. One of our PCs is getting caught in a loop some time after being turned on, usually after a USB storage device has been attached - sometimes an iPod, sometimes a GPS. Specifically, Windows Explorer starts showing a drive icon and letter (E:, as of right now) for the System partition (the small hidden one at the start of the boot drive). Then, the icon disappears. Then it reappears again. And disappears. It does this very quickly, at what looks like maybe 50 times a second. CPU usage in this loop is also very high; averages about 66%. This machine has an i7 920 CPU, which is quad core with hyperthreading; so this usage rate works out to about 5 100% busy threads, along with whatever normal idle load is (particularly Task Manager itself). Inspecting with Process Explorer shows that the device removal notification infrastructure has gone berserk. The threads in system service processes (i.e. apart from Windows Explorer) which are using all the CPU power relate to device notification. The Disk Management MMC snap-in also fails to run when the loop starts. The only way to break the loop, it seems, is to reboot the machine. Anyone seen anything similar to this, and know of a way to fix it? Machine details: Windows 7 x64, fully patched i7 920, 12GB RAM Intel SSD 80GB (X25-M, I believe; not G2) 2TB 5.2K disk for bulk storage AMD HD 5870 Further hardware details await. I'm going to go through and update all drivers I can find.

  Read the article

• Limited user requires admin rights for plug and play printer?

  - by Kalamane

  I have a small fleet of laptops that aren't part of a domain running Windows XP Pro SP3 as limited users. They are used for printing different shipping documents. I have a script that runs when they start up that uses devcon and prntmngr to detect and install/configure the currently connected usb printers. This lets us deploy the laptops to any printing station with a USB printer and have the printer 'just work' for the end user employee. I've taken the original clone image and have added functionality to it. Since then I've discovered a bit of an issue with using HP LaserJet P1606dn printers. They have started asking for admin rights on setup. This is with and without the script running. Previously they would automatically install because I had installed WHQL plug and play drivers for them. I thought it might have to do with the HP Smart Install Utility but it happens when that is disabled. I don't have a good point to roll back to before this started happening because this was an issue on the image I took initially to start this upgrade. What could be causing this?

  Read the article

• Getting PAM/user info into php - something like Net_Finger instead of a db?

  - by digitaltoast

  I've got a very small user group who just need to login, upload, check and then move specific files to a different area when ready. Right now, I use the nginx PAM auth module to log them in against their unix accounts. As their login is their home directory, I've already got the info to send the uploads to the right area - one line of php and no database needed. But I'm maintaining a separate DB just so PHP can welcome them, grab their email and send them an email when processed. Yes, sure I could use nosql or sqlite instead so as to not need a whole mysql install. But it occurred to me that as I've got all these blank user fields for phone numbers I could populate with any data, that I could use something like php's Net_Finger. Which failed for me with: sudo pear install Net_Finger Starting to download Net_Finger-1.0.1.tgz (1,618 bytes) ....done: 1,618 bytes could not extract the package.xml file from "/build/buildd/php5-5.5.9+dfsg/pear-build-download/Net_Finger-1.0.1.tgz" Download of "pear/Net_Finger" succeeded, but it is not a valid package archive Error: cannot download "pear/Net_Finger" At which point I thought I'd stop, and take a ServerFault reality check - is this a really bad/dangerous/stupid idea just to stop me having to maintain details in two places rather than one? It there a better way? Googling shows that it's not an oft-asked thing, so perhaps with good reason?

  Read the article

• Why does my ftp(e)s server fails like half of the time

  - by user1092608

  I have this discussion at work regarding our ftp server running via vsftpd. Initially, we have opted to serve ftpes instead of sftp because this seemed the most flexible and straightforward solution for our server to have secure file transmission. Afterwards, our ftp server seems to be a source of issues for our end users. Half of the time, users complain about not working ftp connections. I must say, i tested our FTP trough different infrastructures (=in the field, at random times at random places) and indeed, sometimes behind some configurations (=no idea how they are configured, because the 'field' testing), i recieve errors. Some of the are: Error: Failed to retrieve directory listing (filezilla) Furthermore, behind my basic home configuration, everything seems to be running fine. I (think I) did all the basic configuration checks (passive mode?, firewall for all ports?, ...) and can't seem to find the source. Being a bunch of techies at our small office, yet knowing nothing about infrastructure, some start suggesting that ftps protocol could be the source of issues. ("No, i only knew sftp so far" "Ftps is not widespread"). I, however, strongly doubt this hypothesis, since reading around on the www, asking questions on serverfault, everyone seems to deny this. So, as I would like to avoid reconfiguring, since this involves messing around in our SSH service, our virtual user setup and ftp service, i would need some advice on 1) what could be potentially the general cause? 2) do you have some general tips? 3) would you mind having a look at my configuration file? ----- General Settings ----- write_enable=YES dirmessage_enable=YES nopriv_user=ftpsecure ftpd_banner="Welcome to XXXX FTP!" hide_ids=YES hide_file=.* max_per_ip=10 max_clients=10 local_enable=YES local_umask=022 chroot_local_user=YES secure_chroot_dir=/usr/share/empty userlist_enable=NO userlist_deny=YES userlist_file=/etc/vsftp_deny_users guest_enable=YES guest_username=ftpvirtual virtual_use_local_privs=YES user_sub_token=$USER local_root=/srv/ftp/ftpvirtual/$USER anonymous_enable=NO syslog_enable=NO xferlog_enable=YES xferlog_file=/var/log/vsftpd_xfer.log connect_from_port_20=YES pam_service_name=vsftpd listen=YES listen_port=21 pasv_enable=YES pasv_min_port=30000 pasv_max_port=30030 pasv_address=foo ssl_enable=YES rsa_cert_file=/etc/vsftpd.pem rsa_private_key_file=/etc/vsftpd.pem force_local_data_ssl=YES force_local_logins_ssl=YES ssl_tlsv1=YES ssl_sslv2=YES ssl_sslv3=YES ssl_ciphers=HIGH anon_mkdir_write_enable=NO anon_root=/srv/ftp anon_upload_enable=NO idle_session_timeout=900 log_ftp_protocol=NO dsa_cert_file=/etc/vsftpd.pem Thanks

  Read the article

• Are there tools available for trimming PDF margins?

  - by Charles Duffy

  I have an ebook I'm trying to read in PDF format on a Kindle. Unfortunately, the page headers and footers have some content (page number and copyright info, respectively) preventing the device from scaling the actual text to match its usable area viewing area, thus leaving the actual content too small to read. Various tools are available which will trim off whitespace, but the Kindle already does this; my goal, by contrast, is to remove printed matter outside of a defined bounding box, and the only tool I've found for the purpose is moderately expensive commercial software. I could probably generate a mask in Inkscape; split out the individual pages using pdftk, apply the mask to each page individually (outputting to postscript), and recombine the numerous postscript files into a single PDF. However, this decode/reencode steps would be pretty unfortunate in terms of document size; something able to operate with a bit more finesse would be ideal. I have all major operating systems handy (Windows, several modern Linux distros, a Mac, etc) so solutions don't need to be constrained by platform. Suggestions? (I've reported the issue to the author, who mentioned it to his editor, who hasn't done anything about the issue over the course of more than a month, making the zero-work approach evidently nonproductive).

  Read the article

• Scaling a LAMP website hosted on EC2

  - by Gublooo

  Hello, I'm very new to all this - I've recently managed to launch my website on EC2. As next step, I want to learn how to scale the website. I have a general idea but wanted some input from the experts about how to go about it. My website is based on LAMP but also has Red5 server which allows users to record messages and also used for playing them back. Currently this is the architecture I'm planning to setup for initial scaling. Deploy four small EC2 instances for the following purposes: Instance-1: On this instance I will run the MySql database Instance-2: On this instance I will run the red5 server Instance-3 & Instance-4 These 2 instances will be used to deploy the website and will have Apache running on them. They will communicate with the mysql server on Instance-1 and red5 server on Instance-2 using the internal IP address. As an when required, I will launch another instance of the same EBS - I will have EBS of say 50 GIG where all the mysql data will be stored. Also red5 will use this EBS to store the video messages Load-Balancer - Use the load balancer provided by Amazon to load balance Instance-3 and Instance-4 This is what I have in mind. I could be way off so please bear with me. Also I have not taken into account the case of scaling MySql server as I currently have no idea about how that will be done and whether or not it is necessary initially. I am aware that Amazon provides auto scaling and mysql scaling as well but I dont want to get into that right now. Your feedback is appreciated Thanks

  Read the article

• Network card shuts down when stressed

  - by user142485

  I have a network card that functions fine with light use, but quits functioning after heavy use. I replaced it with a brand new one and still have the same issue, also updated drivers. It is a wired D-Link card. The Internet seems fine for a small amount of web browsing but when I run a bandwidth test it starts out fast and slows quickly until the card completely quits; I have a constant ping of the gateway going while I run this and it starts timing out after a couple seconds into the speed test. The card will stay on and the data light on it still flashes some but I cannot ping the gateway or anything else until the computer is rebooted. When I boot into safe mode I can browse and run the speed test fine with no problems. I am guessing that this is probably some program that is loading in regular mode but not safe mode that is causing the issue? I have very limited software (turned off av and firewall) on the computer but I am thinking that I'll just have to start eliminating start-up programs and see if that helps. This is on Windows 7 if that makes any difference. Anyone had a similar issue or have any other suggestions/ideas for narrowing down this problem?

  Read the article

• How to change font size on display

  - by Tim

  My laptop is Lenovo T400, whose screen size is 14.1 inches and default resolution is 1440 x 900. My main OS is Ubuntu 10.10. The default font size on the display is somehow small, which might contribute to the fatigue of my eyes. My previous laptop is Acer 5000, whose screen size is 15.4 inches and the default resolution is 1024 x 768. I like reading on my old laptop better than on my new one. Is it possible to change the setting of my new one to look like reading my old one? What are the parameters that control the font size? Are screen size, resolution part of them? In Windows, there are choices for font size, while in Ubuntu I haven't find out where I can change the setting and would like know if someone here knows about it. I also wonder if I can use a separate bigger display (perhaps just like a desktop display) as the display of my laptop, in case I don't want to enlarge font size at the cost of sacrificing the amount of the content to display, and how I shall do it? Thanks and regards!

  Read the article

• Many clients on a wireless AP for UDP broadcast packets

  - by distorteddisco

  I asked this question on StackOverflow and was directed over here, so I'd appreciate any advice. I'm deploying a smartphone application as part of a live music performance that depends on receiving UDP broadcast packets from a wireless access point. I'm guessing that between 20 and 50 clients will be connected at any one time. I'm aware that a maximum of 20 clients per access point is advised, but as the UDP broadcast packets are ground through the LAN, how would I be able to link multiple APs together? I'm looking for recommendations on a suitable AP for this. The actual data transmission rates are very low - only a few kB/s - as I'm just sending small messages to the smartphone apps, and there will be no WAN internet connection. I tried it with a few connected peers on an adhoc wireless connection without any problems, but ran into dropped packet issues on an old WRT54G running ddwrt, though it's in pretty rough shape. What's the best way to do this? I suppose I could limit concurrent wireless connections to 20 clients... but more would be nice. EDIT: I should also say that it's purely one-way communication; the smartphone application is only receiving broadcast packets, not sending anything.

  Read the article

• Window too big to fit the screen!

  - by syockit

  I'm using Windows 7 on a 8.9' monitor with 1280x768 screen resolution. Using the might of arithmetics, I'm able to determine that my dpi (actually ppi) should be 167. Win7 is really helpful in that it doesn't have to restart to apply new dpi settings, unlike its predecessors (though I'd rather it applies straight away). The problem with small monitors in Windows is that when you come across windows too big to fit the screen, you can't move the title bar far above it. In X window managers I used in the past, you could alt-drag the window to anywhere you want, but in Windows, even if you alt-space and select move, it will automatically push the window back until the title bar is visible. I'm looking for a solution that either: allows me to move window freely without regard to titlebar visibility, or attach a scrollbar to existing window, or EDIT: create virtual desktops that allow me to span windows over 2 desktops, or EDIT 2: allow me to set larger virtual resolution, then pan & scan. EDIT 3: I found some progs that might do some of the above: 1) AltDrag allows me to drag, resize using alt and left/right mouse button. Neat! Best solution so far. 2) GiMeSpace Desktop Extender is supposed to allow me to scroll desktop. Didn't work. The other new version, GiMeSpace Ultimate Taskbar worked, but it destroys my Superbar, replacing it with its map.

  Read the article

• Centralized backup method recommendation for SMEs with various OSes

  - by Akinator

  Hi I was wondering what in your opinion is the "best" method for having "everything" backed-up in the following situation. We are a SMEs with 10 computers in total. Three of those computers are MACs The rest are windows (1 vista, 4 win7 and 2 XPs) I'm very open to what the method should be but you should also consider the follwing: Very limited resources Quite "small" bandwidth (4 MBs for all (download) 0.4 MBs (upload, yep, thats it)- though this might get, a little bit better) One of the main thing to back up would be the mails, considerations: All windows computers use outlook, mainly 2003 There is one mac that uses outlook too (for mac of course - not 2011 yet) We also have to backup the files: Not a huge amount Very few very big files Very organizes (by machine) What I would like is to hear your opinions as to which would be the best method (or combination of methods - preferably one of course) considering. We are not sure what do we need and I'm open to suggestions, though an online (cloud based applications) would be great, remember the the bandwidth is unbearable. Last think to consider, it that we would like to do weekly updates (unless the method is very easy of course). Thanks in advance!! I tried to be as specific as possible, but if anything is needed I'll gladly update, please ask for any clarification needed! Please avoid any answers like upgrade all to windows 7 and throw away your macs :) our's may not be an ideal situation, but it is what it is, and right now, it would be impossible for us to change it for a lot of circumstances.

  Read the article

• Confused with creating an ODBC connection, apparently I have two separate odbcad32.exe files?

  - by Hoser

  Alright, this is my first time working with this so forgive me if I'm a little confusing or vague. I have a server with Windows Server 2008 Standard without Hyper-v (6.0, Build 6002). I'm running a small website off this server and using a Microsoft Access database to store some information coming in through the website. I'm sure the PHP I have written to open the ODBC connection is correct as it has worked for me when I created this website in a testing environment on a laptop. My current issue now is that it seems like I have two different odbcad32.exe's, and one doesn't appear to have a driver for a .accdb file, and only a .mdb file. The other has a driver for both. The first one I speak of has a driver titled 'Driver do Microsoft Access (.mdb)', the second one has a driver titled 'Microsoft Access Driver (.mdb, .accdb)'. I access the first odbcad32.exe by going to C:\Windows\SysWOW64\odbcad32.exe, and then the one that seems to have the driver I need I go to Control Panel-Administrative Tools-Data Sources(ODBC) and simply create a new connection in the System DNS tab. Whenever I make changes to the one that I access through the Control Panel, I see no changes, however if I use the odbcad32.exe file in SysWOW64 I do get some changes in the errors that come back to me. The main difference I noticed is that when I set up an ODBC connection with the Control Panel method it said it simply couldn't find the ODBC connection, but when I made a .mdb connection in the SysWOW64 one (and pointed it to a .accdb file) it says Cannot open database '(unknown)'. It may not be a database that your application recognizes, or the file may be corrupt. Which makes it seem like it is this odbcad32.exe version in SySWOW64 that is being recognized as the 'correct' one. Is there any way to fix this? I've tried to be as thorough as possible but if I've been confusing or left anything out let me know.

  Read the article

• How can I get mouse capture to work in virtualbox when I move guest window to second monitor?

  - by Dan

  I'm running VirtualBox on a Win7 host. Guest OS is Centos. My setup is a laptop (screen 1) with a huge external monitor (screen 2). I'm only telling Centos there is one monitor though. When I start up VirtualBox on screen 1, the mouse capture works fine. I don't have mouse integration because (I think) the kernel on Centos is too old to support it. That's fine, I don't mind doing the Right-Control thing. The problem I have is that when I drag the whole VM window over to my second monitor, the mouse capture doesn't work right anymore. I click inside the VM and can move the VM cursor a little bit, but I can't always get to the edges of the VM screen -- before I get all the way to an edge, the cursor will escape from the VM as if I had hit right-control. But it's still captured according to the icon, and if I then hit right-control, the guest cursor jumps to a different screen location. My workaround: if I have the VM window mostly on screen 2, but a small corner of it still on screen 1, then the mouse capture works correctly. Is there a setting to make this work better?

  Read the article

• PHP Web Server Solution (Apache/IIS)

  - by njk

  I apologize if this is too broad or belongs on Super User (please vote to move if it does). I'm in the process of creating requirements for an internal PHP web server to submit to our architecture team and would like to get some insight whether to use a Windows or *nix platform and what applications would be required. The server will host a small PHP application that will be connecting to SQL Server. The application will need to send mail. We would also like to incorporate a FTP server to allow files to be dropped in. From what I've read regarding a Windows platform using IIS, it seems as though IIS would only be advantageous if using a .NET or ASP application. Does IIS have mail functionality? Or how is mail traditionally configured (esp. on *nix)? Also, does IIS have directory configuration functionality like Apache does with .htaccess? For a Windows based solution; IIS (comes with FTP) Apache (has mod_ftp module) For a *nix based solution; Apache

  Read the article

• Low-profile, PCI Express, x1 video card with VGA-out?

  - by Dandy

  I just bought an Acer Aspire EasyStore H340 system (http://us.acer.com/acer/productv.do?LanguageISOCtxParam=en&kcond61e.c2att101=54825&sp=page16e&ctx2.c2att1=25&link=ln438e&CountryISOCtxParam=US&ctx1g.c2att92=450&ctx1.att21k=1&CRC=936243954) It comes with Windows Home Server, which I don't particularly care for (too dumbed down for my liking)--I bought the box mainly for the form factor, and intend to install Server 2008 on it and have it run as a small domain controller. The geniuses at Acer however went out of their way to ensure you can only run Home Server--you can only connect to it via the Home Server Connector software, as it has no video-out whatsoever (so essentially, there's no way to even get into the BIOS). It only has a low-profile, PCI Express x1 slot. It turns out to be way harder than I thought to locate a video card that both has an x1 connector, and is low-profile (I'd really rather not snip the bracket at the back just so it'll fit the case). I know they're out there, and I've seen one with Display Port outputs, but I don't have a monitor with this connection. So to reiterate, it needs to be: - x1 connector - low profile - VGA out (though DVI would be okay; I have some spare adapters) Can anyone recommend anything at all?

  Read the article

• Best way to restrict access to a folder in Dropbox

  - by Joe S

  I currently run a business with around 10 staff members and we currently use Dropbox Pro 100GB to share all of our files. It works very well and is inexpensive, however, I am taking on a number of new staff and would like to move the more sensitive documents into their own, protected folder. Currently, we all share one Dropbox account, I am aware that Dropbox for teams supports this, but it is far too expensive for us as a small company. I have researched a number of solutions: 1) Set up a new standard Dropbox account just for use by management, which will contain all of the sensitive documents, and join the shared folder of the rest of my team to access the rest of the documents. As i understand it, this is not possible with a free account, as any dropbox shared folder added to your account will use up your quota 2) Set up some sort of TrueCrypt container, and install TrueCrypt on each trusted staff member's machine, and store the documents inside that. Would this be difficult to use? I'd imagine the sync-ing would not work so well as the disk would technically be mounted at the time of use and any changes would be a change to the actual container rather than individual files. I was just wondering if anyone knows a way to do this without the drawbacks outlined above? Thanks!

  Read the article

• I need to build a mini computer lab with 6 PCs

  - by chiurox

  Hello everyone, This weekend I need to build a mini computer lab with 5-6 PCs. The purpose is for a small computer class that will be taking place. They're mostly going to be doing office and daily kind of stuff, so nothing high performance. However, I hope it will last at least for 2 more years. I already have some parts for 2 PCs, one is a P4 3.0 and another is Celeron 2.4GHz, both socket 478. For the other 4 PCs, I'm wondering if I should buy individual parts and put it all together or get workstations like those Dell Optiplex with P4s. To put things into perspective, I am not currently in the US. I'm in South America and prices here are ridiculously. Another really important thing is that I need to share an internet connection between a total of 8 PCs at this place. Right now I only have a crappy wireless router, should I get another one? Or go with switch hub? I'm not experienced in this matter. Thanks guys!

  Read the article

• Locate devices within a building

  - by ams0

  The situation: Our company is spread between two floors in a building. Every employee has a laptop (macbook Air or MacbookPro) and an iPhone. We have static DHCP mappings and DNS resolution so every mobile gets a name like employeeiphone.example.com, every macbook air gets a employeelaptop.example.com and every macbook pro gets a employeelaptop.example.com on the Ethernet interface (the wifi gets a dynamic IP from a small range dedicated for the purpose). We know each and every MAC address of phones and laptops, since we do DHCP static mapping (ISC DHCP server runs on linux). At each floor we have a Netgear stack of two switches, connected via 10GB fiber to each other. No VLANs so far. At every floor there are 4 Airport Extreme making a single SSID network with WPA2 authentication. The request: Our CTO wants to know who is present at which floor. My solution (so far): Every switch contains an table listing MAC address and originating port. On each switch stack, all the MAC addresses coming from the other floor are listed as coming on port 48 (the fiber link). So I came up with: 1) Get the table from each switch via SNMP 2) Filter out the ones associated with port 48 3) Grep dhcpd.conf, removing all entries not *laptop and not *iphone 4) Match the two lists for each switch, output in JSON or XML 5) present the results on a dashboard for all to see I wrote it in bash with a lot of awk and sed, it kinda works but I always have for some reason stale entries in the switch lookup tables, making it unreliable; some people may have put their laptop to sleep, their iphones drop connections after a while, if not woken up and so on..I searched left and right, we are prepared to spend a little on the project too (RFIDs?), does anybody do something similar? I can provide with the script if needed (although it's really specific to our switches and naming scheme). Thanks! p.s. perhaps is this a question for stackoverflow? please move if it so.

  Read the article

< Previous Page | 396 397 398 399 400 401 402 403 404 405 406 407  | Next Page >