Search Results

Search found 11524 results on 461 pages for 'pc wiki'.

Page 401/461 | < Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >

  • How to enable Ipv6 on my ubunutu 11.04 virtual machine

    - by liv2hak
    I have installed 3 VM's on my PC.(Ubuntu 11.04).I want to setup an IPV6 network to review and test some of the IPV6 tools like NDPMonitor.(monitors ICMP messages of Neighbour Discovery Protocol.) IP v6 addresses are as follows. linux_router - fe80::a00:27ff:fed5:f7e9/64 labhack1 - fe80::a00:27ff:fed2:8bd1/64 labhack2 - fe80::a00:27ff:fed7:2f2d/64 The below commands have been run on both linux_router and labhack1. sudo ip r a 2001:468:181:f100::/64 dev eth0 sudo vim /etc/radvd.conf /file looks like below./ interface eth0 { AdvSendAdvert on; /*means that we are sending out advertisments.*/ MinRtrAdvInterval 5; /*these options control how often advertisments are sent*/ MaxRtrAdvInterval 15; /*these are not mandatory but valueable settings.*/ prefix fe80::a00:27ff::/64 { AdvOnLink on; /*Says to the host everyone sharing this prefix is on the sam local link as you.*/ AdvAutonomous on; /*Says to a host: "Use this prefix to autoconfigure your address"*/ }; }; sudo sysctl -w net.ipv6.conf.all.forwarding=1 I try to do a ping6 -I eth0 fe80::a00:27ff:fed5:f7e9 I get Destination unreachable: Address unreachable.I am not sure what I am doing wrong here.I am a beginner at linux administration.Basically I think I am missing whatever is analogous to physically connecting VM's.Any help that would point me in the right direction would be greatly appreciated.

    Read the article

  • OS X Hard drive recovery

    - by Adam
    I am trying to recover data from a bad Seagate 1TB hard drive in a 2010 iMac. One day the iMac wouldn't boot (stuck at gray screen on startup). I removed the hard drive from the iMac and connected it to a MacBook using a 3.5" HDD to USB adapter. The hard drive wouldn't mount but it did display in Disk Utility that that there were 2 partitions on the disk. I tried to run Disk Warrior and it showed thousands of errors but still wouldn't mount. At this time the hard drive only show one partition in Disk Utility. Next I tried putting the hard drive in a desktop PC and running Spin Rite - which then gave me several division overflow errors (even with running Spin Rite with a newer version of DOS). The SMART status on the drive reports that the drive has had failures and HD Tune referenced the drive had once hit 59 degrees celsius. Disk Utility gives me the following message when running a pair: Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files. Overall, the hard drive spins up and sounds OK - there are no clicking noises but the hard drive won't mount and displays as a light gray "Macintosh HD" in disk utility. Any tips or advice on how to recover data on this drive would be GREATLY appreciated! Are there any other tools I can try before calling it quits on this drive? Thank you

    Read the article

  • Why can't I install Java?

    - by Patrick
    I've been searching high and low for someone who can help me. I've been trying for a month. A month. to install Java on my new PC to no avail. No tech support forum can seem to help me. It all started while playing tekkit one day. I kept running out of memory (using the 32-bit JRE 7 u45) so I decided to install the 64-bit version. I uninstalled the 32-bit version first, for some reason, and downloaded the 64 bit runtime. In the installer, I go through all the normal screens until the installation progress bar appears. Then, it just sits there. No progress is made. No CPU is used by the installer, or any of its dependencies. The installer will stay like this for hours, days, and in one case a whole week without doing anything at all. I've tried installing older versions, the 32-bit version, even Java 6 and none of them will install. UAC is disabled, I've run regedit, CCleaner, and any other "fix-it" program there is. It's getting to the point where I may just have to wipe my hard drives and start over. I have several applications that require java, so this is an absolute necessity. Please, please, someone have the answer. Here are my system specs: -Intel i7-3770k -AsRock z77 Extreme3 -Samsung 840 pro SSD -WD Caviar Black 1tb

    Read the article

  • How can I get my SATA DVDs working again?

    - by user269051
    My hard drive crashed (WinXPpro), so I took a C drive from a broken PC. The new C drive is Win7pro. Motherboard is MSI K8N Neo4 Platinum, with 4 hard drives installed on SATA 1-4 (nForce4 Ultra); the two DVD drives are loaded on SATA 7-8 (Silicon Image SATARAID5). I've tweaked BIOS settings every which way. The closest thing to success was when each DVD had both a CD and a DVD icon, and blinked green. No CD or DVD could be read in either drive. I assume that the problem resulted from the fact that my new C drive does not have the RAID drivers? I've tried loading from the floppy (doesn't work). I can't boot off the DVD/CD, and switching the DVD's SATA cable to the SATA 3 slot (and pulling one of the hard discs) didn't work. I'd like to be able to use the other two available SATA slots for a mirrored RAID drive, and get my DVDs working again. Any suggestions?

    Read the article

  • DNS server not working?

    - by Behrooz A
    I just set up a DNS Server on my windows 7, called SimpleDNS I added a zone for example sag.com and defined www.sag.com and sag.com to 192.168.1.2 (my Network IP Address) . the problem is when I try to ping sag.com the SimpleDNS logs says that it answered the request with 192.168.1.2 , but the ping doesn't resolve anything . SimpleDNS logs: > 14:00:43 Request from 192.168.1.2 for A-record for www.sag.com > 14:00:43 Sending reply to 192.168.1.2 about A-record for > www.sag.com: 14:00:43 -> Answer: A-record for www.sag.com = > 192.168.1.2 14:00:43 -> Authority: NS-record for www.sag.com = mehr-pc nslookup : > C:\Users\Mehr\Desktop>nslookup www.sag.com DNS request timed out. > timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 > > DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. > *** Request to UnKnown timed-out the DNS server IP is 192.168.1.2 , and Access point address : 192.168.1.1 what should I do?

    Read the article

  • DNS server not working?

    - by Behrooz A
    I just set up a DNS Server on my windows 7, called SimpleDNS I added a zone for example sag.com and defined www.sag.com and sag.com to 192.168.1.2 (my Network IP Address) . the problem is when I try to ping sag.com the SimpleDNS logs says that it answered the request with 192.168.1.2 , but the ping doesn't resolve anything . SimpleDNS logs: > 14:00:43 Request from 192.168.1.2 for A-record for www.sag.com > 14:00:43 Sending reply to 192.168.1.2 about A-record for > www.sag.com: 14:00:43 -> Answer: A-record for www.sag.com = > 192.168.1.2 14:00:43 -> Authority: NS-record for www.sag.com = mehr-pc nslookup : > C:\Users\Mehr\Desktop>nslookup www.sag.com DNS request timed out. > timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 > > DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. > *** Request to UnKnown timed-out the DNS server IP is 192.168.1.2 , and Access point address : 192.168.1.1 what should I do?

    Read the article

  • Ubuntu xrandr rotate issue

    - by user83544
    I've just bought a second monitor for my PC which happens to be a pivot monitor. I've already read lots of forums related to my problem but haven't come across a solution - I have the same symptoms as dozens of posts but no matter whatever I try it just doesn't work. I've already changed the xorg.conf file and added in the device section just under Driver "nvidia" the following for my second monitor: Option "RandRRotation" "on" When I save and reboot I try to rotate my screen with the nvidia X server settings by choosing the second monitor and clicking either "left" or "right" for the rotation. It immediately exits the nvidia settings window and does nothing. I tried within the terminal by typing: xrandr -o right I get the following error: X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 154 (RANDR) Minor opcode of failed request: 2 (RRSetScreenConfig) Serial number of failed request: 14 Current serial number in output stream: 14 I actually manage to rotate it with Option "Rotate" "CCW" instead of "RandRRotation". The problem with this solution is that you get the second monitor in the right position, but any window you open on that screen is practically unchangeable. You can't change the size nor move it, making it useless for reading PDFs, which is the main reason why I bought this second screen to help me write my thesis. Any help is really appreciated. sudo lshw -c video hiram@hiram-linux:~$ sudo lshw -c video *-display description: VGA compatible controller product: nVidia Corporation vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:f8000000-f9ffffff memory:d8000000-dfffffff memory:d4000000-d7ffffff ioport:dc00(size=12 memory:fbd80000-fbdfffff

    Read the article

  • Ubuntu 12.04 compiz - disable all compiz plugin - empty screen

    - by gotqn
    A lots of thanks to terdon who spent so many time on this and finally solve the issue. A friend of mine has installed on my new machine Ubuntu 12.04 (I have always been windows user and have no experience with Linux). I started to watch some tutorial about how to make 'Rotated Cube' using 'Compiz',but the cube appears in the form of a list (only two slides). I have thought this could be result of my video cards (only two - one from the processor and one from the motherboard) and they can not support this options. Anyway, I have decided to disable all compiz plugins and options because my friend has set some, and I started to think there is some misunderstanding between the plugins. After, that I got only empty screen(no menu, no icons, anything) and can do nothing. How to fix this? EDIT: When I remove the compiz stuffs (from the console), the menu is shown again. Then I install the compiz again (some of the effect are still not working). After restart or log out/in the menu is hidden again. I suppose that there are some settings that I've broken but they are saved somewhere in the system and remove the compiz do not deleted them and as a result they are activated after compiz is installed again and the PC is restarted?

    Read the article

  • emacs error: "Symbol's value as variable is void: hostname"

    - by Florian Pilz
    After I installed emacs this error occurs every time on startup. It prevents me from installing plugins, e.g. auctex via aptitude. I already tried to install a plugin by hand (rails for ruby), but doesn't work. The error doesn't contain the message "hostname", but the hostname of my PC is displayed ("bloodredangel-ubuntu"). I changed my hostname to "bloodredangel", but the error message stays the same. While I changed my hostname I saw that in /etc/hostname were two entries: 127.0.0.1 bloodredangel-ubuntu I already asked this question in an ubuntu forum but they couldn't help. They recognised an misconfigured /etc/hosts file, which I corrected, but from time to time these incorrect configurations get attached by something. I didn't add them by hand, maybe it has something to do with the issue. The misconfigurations looked like this: 127.0.0.1 127.0.0.1 bloodredangel-ubuntu localhost.localdomain localhost 127.0.0.1 127.0.0.1:8080 bloodredangel-ubuntu localhost.localdomain localhost I didn't found a solution on the internet, so I hope I will find help here finally.

    Read the article

  • Why do I have 55 local area connections in ipconfig?

    - by RMorrisey
    Windows Vista Home Premium. I should mention that I am having no problem whatever getting an internet connection. When I type "ipconfig" in the console, I get (55!) messages of 3 lines each, listing a ton of disconnected network connections. My PC only has one network card. Each message looks like this: Tunnel adapter Local Area Connection* 55: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : These don't cause a major problem; they make it a pain, though, to fish upward and find my IP address. How can I get rid of them? Edit: Actually, a few connection numbers are randomly missing from the sequence; so, it's really more like 30 or 40 connection messages, rather than all 55. Not sure why that is, either.

    Read the article

  • file association in Windows 8

    - by Robith Nuriel Haq
    Associating a file to a program should be easy in Windows. However, i find it rather difficult when I'm working on Windows 8. associating a file to a desktop application that I install on my computer is easy because the whole operation is entirely the same with that in the previous Windows releases. What I find rather difficult is associating a file to a Metro apps that I download from the store. So far, I have been using Multimedia 8 (a metro app) to open my video files. However, this app cannot handle particular files-like *.dat-that can be associated easily to desktop video applications, such as media player classic and the like. When I try to associate my DAT files to Multimedia 8, there is indeed a "look for another app on this PC" option at the bottom of the "open with" pop up. But alas, I cannot figure out how to locate my Multimedia 8 app to which I want to associate my DAT file (as well as other video files that are not yet associated to this metro app). If anyone of you knows how to locate those metro apps, please tell me. many thanks

    Read the article

  • Computer restarts without warning; code bcc116

    - by Robert C.
    Processor: Intel i5 4430 4-Core 4x3Ghz Motherboard: msi h87-g41 Graphics Card: Nvidia GTX760 Power supply: eps-750 cm RAM: 8GB I bought a new assembled gaming PC which worked fine for a few days. Then it started rebooting without warning. After it restarts windows 7 gives me an bbc 116 error code. Apparently it's something to do with my video card, either it overheating or wrong drivers. I've installed the latest driver from Nvidia for my graphics card. Since it's brand new it can't be dust, I'm running it with its lid open to see if the problem persists. I'm also running prime95 now to see if it tells me anything else. Using core temp it tells me that my CPU reaches up to 95° celsius with the blend stress test from prime95. Aaaand it just peaked to 100°. Of course it doesn't reach these temperatures at all while idle/gaming. I'm gonna let prime95 run for a night and to see what happens. Until then does anyone know what I should do next?

    Read the article

  • Cannot Kill Process in Vista 64

    - by JanSolo
    Hi I have a weird situation where a Zombie process is causing my Vista64 Dev machine to become useless. I use Incredibuild 3.40 to distribute builds of a large software product that I work on. Occasionally, a build will fail and a Zombie process is left behind. The process holds a handle to a file that is needed by the build system to retry the build. Since I cannot kill the process, the handle remains open and I cannot build my code at all. I've tried TargetManager and ProcessExplorer, but neither can kill this process. It gets worse; since Vista cannot kill all its processes, my PC refuses to shut down correctly, requiring a hard reboot after each failed build. Is there a way to really-really-kill a process in Vista? Or maybe a way to force a file handle to close? Any help is appreciated. Cheers Jan. EDIT: This is still occurring. I've used Lockhunter (which appears to successfully unlock the file handle), but retrying the build still fails because the (now unlocked) file cannot be deleted. Explorer and Lockhunter both fail to delete the file. LockHunter also tells me that there are no processes that hold handles to it. Basically, nothing owns it, but you still cant delete it. This sucks.

    Read the article

  • No digital audio output with Asus Xonar DG

    - by Lunatik
    I've purchased an Asus Xonar DG as replacement for faulty onboard audio in a Medion 8822 as it has an optical output which is all I really need to feed my HTPC. I uninstalled the previous drivers/devices, switched the PC off, inserted the Asus card, powered up, disabled the onboard audio in the BIOS, then installed the driver that came on the CD (same version as on Asus' website as of today) and everything went perfectly - no errors. I set the audio devices up in Windows and in the Asus utility (SPDIF enabled, 6-ch audio) as I would expect to see them work, but the only thing is I have no digital audio from test tones within Windows/the Asus utility, PCM audio or Dolby Digital from DVD. Analogue audio is fine. I've uninstalled things and reinstalled a couple of times now, as well as trying almost all combinations of analogue/digital outputs but can't get it sorted. Does anyone have any tips on how to get this working? This card has just been released so there isn't much out there to go on. Notes: The light on the toslink port is lit. OS is Vista 32-bit SP2 and all up to date, pretty much a fresh install with almost no 3rd party applications installed This page seems to suggest that a digital output device in Windows is not needed with Xonar cards as it was with the previous Realtek so I have it set to Analog. The only other output device is S/PDIF pass-thru

    Read the article

  • IP address from a MAC address

    - by acermate433s
    I'm writing a class to integrate a POS card reader device to our software. In order for it to work I must know what IP it's using. We were given some sample code by the service provider and the way they do this is they open a website (http://www.ebizchargeemv.com/getip.php?mac={MAC address of device}) and it would return the IP address of the device. The device I'm using is a POSLynx220 Mini. It has an ethernet port that connects to the internet to communicate with the service provider. I send TCP data to it and the device then controls a PIN pad that prompts a client to swipe his card. It's probably a mini computer that communicates with the service provider and uses the PIN pad as its input device. Just being curious but how did they implement this? Are they implementing it using ARP? I'm planning on not using their website to determine the IP of the device. I've seen some code that uses ARP but using executing ARP in one of the PC didn't detect the POS device.

    Read the article

  • Limiting bandwith on an Windows 7 machine

    - by Mihai Damian
    I need to limit the bandwidth on my Windows 7 x64 machine. In the past (on XP) I've been able to use NetLimiter for similar tasks. However for some reason I can't get it to work anymore. For lower limits the bandwidth tests are able to exceed the limit by 10-50%; higher limits seem to be ignored completely and the bandwidth tests report download speeds of over 10 times the speed I set. I'm using speedtest.net and some similar service from my ISP for these tests. Anyway, I don't necessarily need a program as complex as NetLimiter since I only need to throttle my machine's bandwidth, not a specific program's. In case you are wondering why in the world I'd want to cripple my Internet speed, there is a funny story behind this. Long story short, my modem gets random disconnects. Tech support comes in, says my Internet speed is abnormally high and I must be using some tools to somehow make it go faster than it's supposed to and this messes up my modem. I check the connection with another computer and it seems that my PC is the only one in my network that gets abnormal speeds. I reinstall my OS, speed looks normal at first, after I install the batch of 50 or so updates, it goes back to abnormally high speeds and the disconnect problems are not solved. Now I don't have a clue if the explanation the tech team gave me was just a strategy to lay the blame on someone else, but I was trying to give them the benefit of the doubt and see what happens if I really reduce my speed to their specification. Any help appreciated.

    Read the article

  • No digital audio output with Asus Xonar DG

    - by Lunatik
    I've purchased an Asus Xonar DG as replacement for faulty onboard audio in a Medion 8822 as it has an optical output which is all I really need to feed my HTPC. I uninstalled the previous drivers/devices, switched the PC off, inserted the Asus card, powered up, disabled the onboard audio in the BIOS, then installed the driver that came on the CD (same version as on Asus' website as of today) and everything went perfectly - no errors. I set the audio devices up in Windows and in the Asus utility (SPDIF enabled, 6-ch audio) as I would expect to see them work, but the only thing is I have no digital audio from test tones within Windows/the Asus utility, PCM audio or Dolby Digital from DVD. Analogue audio is fine. I've uninstalled things and reinstalled a couple of times now, as well as trying almost all combinations of analogue/digital outputs but can't get it sorted. Does anyone have any tips on how to get this working? This card has just been released so there isn't much out there to go on. Notes: The light on the toslink port is lit. OS is Vista 32-bit SP2 and all up to date, pretty much a fresh install with almost no 3rd party applications installed This page seems to suggest that a digital output device in Windows is not needed with Xonar cards as it was with the previous Realtek so I have it set to Analog. The only other output device is S/PDIF pass-thru

    Read the article

  • Thin client - cloud machine - to run via iPad, iPhone, most Androids etc

    - by Carl Lindberg
    I'm tired of having a laptop macbook that breaks down or having files that I need to sync via dropbox etc all the time via the machines to different OS installations. It sucks. I want a thin client where I can login on any machine - my iPhone, PC desktop, iPad etc to one running machine. I would like to replace a modernly powerful desktop iMac with a thin client running via my iPad. I will connect the iPad with a keyboard/mouse too so you get the idea. But I want to be able to use some of the Android phones as well (I guess most Android phones today has a good enough performance/resolution etc to run a thin client). Of course it has to be able to have input/output in sound. Printing can be solved by PDF/emailing etc - so no direct communication to the printer ports to USB etc is necessary. Is there such a service today? It should cost somewhere under something like $40/ month. I will run stuff like CPU heavy duty ableton for music production, xCode for making iOS apps, some games etc. And on the thin client also run virtual machines. VM of Ubuntu and Windows.

    Read the article

  • How to get a higher resolution on Ubuntu 11.04 using an intel chipset

    - by Saif Bechan
    I have a bit slow PC here, so I decided to put Ubuntu 11.04 on it. It use to run Windows Vista on a resolution of 1280x1024, so both my hardware and monitor support it. Now I'm on Ubuntu, but can only run 1024x768, and the screen is not that bright. Its like when you don't have the right drivers on a Windows machine. Now i'm new to linux, so I do not know what do do. I have an onboard Intel chipset i965. Maybe this is some useful information, I read something about it on a forum: lspci 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 03:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) Can someone please tell me how I can get the screen better? saif@sodium:~$ xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9

    Read the article

  • I need an admin toolset for Windows 2003 and 2008

    - by eugeneK
    i know this is way too general question but anyway. I need few tools, will write down my tasks as sysadmin and if you have any to automate my job i would be glad to hear. I don't mind paying for software needed unless it is way too expensive. First of i backup all files on server at local/office storage. I 7zip all SQL backup files and then move them over network to centralized location and then FTP them from office PC which has no FTP server installed and cannot have one. Backups happen at 4AM at the morning thus i need to set time for compressing and afterward FTPing. Then i FTP all IIS web application as differentiation backup, same goes for VOD movies. Second tool i need is system monitor which will monitor all servers from themselves and from external location for CPU/Memory/Hard disk and other basic failures. This tool should able to execute Website address with parameters which will send me an email with all report on failure. Third tool i need is a way to get all Event Logs from 10 Windows based servers without accessing each any of them manually. If you know any solution, thanks in advance.

    Read the article

  • Can't ping my Window 7 machine from within a Windows XP virtual machine

    - by Jonathan Conway
    I have Windows 7 installed as my primary operating system, on a laptop that's on my home network (wireless). I'm using Microsoft Virtual PC 2007 SP1 to run a virtual machine of Windows XP SP3, in which I want to access the Windows 7 instance, both to browse a shared folder and access the local Apache server. So far I can ping my Windows 7 IP address (IPv4) and access the apache server through the web browser through HTTP. However using my machine name never seems to work. Pinging it fails, and I can't access my apache server using it either. The problem seems to be something to do with my machine's name being registered under IPv6 rather than IPv4. I'm at a loss what to do. Should I try to set up IPv6 on the virtual machine? Not sure how to go about that. Or maybe I should somehow get my machine name on Windows 7 to work with IPv4? Although I think it already does, because I can ping it from a separate box (running Ubuntu), which is only registered under IPv6.

    Read the article

  • Install self-signed certificate on local server (iis)

    - by ile
    On this page there are instructions on how to create self-signed cert (on apache) and how to install this certificate on server. I found this page (http://www.visualwin.com/SelfSSL/) with instructions on how to create self-signed certificate on windows (iis). I followed instructions and when I type https://myip/myapp (this leads to localhost because I set my router's port forwarding to go to localhost on my pc) this part works. From the first link, the most important part is this: What needs to be installed in IE is actually the Root CA Certificate. In the how-to above, the Root CA Certificate is called ca.crt. Copy this file to the server that is running QuickBooks. The following is for IE6: - Open IE - Tools - Internet Options - Content - Certificates - Trusted Root Certification Authorities Tab - Import, Next, Browse to 'ca.crt' - Next, Next, Finish, Close, OK The part that is missing in second link is that there is no instruction on how to get .crt file, so I tried to get it myself. What I did was following: I opened https://myip/myapp in Firefox and then "This Connection is Untrusted" screen appeared. Then I clicked on "Add Exception" and then below "Certificate Status" I clicked "View". Under the Details tab I clicked on Export and choosed Save as type: "X 509 Certificate (PEM)" and file was saved with .crt extension. Then I opened IE8 and followed above instructions. After opening https://myip/myapp in IE8 I always get warning screen. Does anyone knows what am I doing wrong? Thanks, Ile

    Read the article

  • libstdc++ - compiling failing because of tr1/regex

    - by Radek Šimko
    I have these packages installed on my OpenSUSE 11.3: i | libstdc++45 | Standard shared library for C++ | package i | libstdc++45-devel | Contains files and libraries for development | package But when i'm trying to compile this C++ code: #include <stdio.h> #include <tr1/regex> using namespace std; int main() { int test[2]; const tr1::regex pattern(".*"); test[0] = 1; if (tr1::regex_match("anything", pattern) == false) { printf("Pattern does not match.\n"); } return 0; } using g++ -pedantic -g -O1 -o ./main.o ./main.cpp It outputs this errors: ./main.cpp: In function ‘int main()’: ./main.cpp:13:43: error: ‘printf’ was not declared in this scope radek@mypc:~> nano main.cpp radek@mypc:~> g++ -pedantic -g -O1 -o ./main.o ./main.cpp /tmp/cc0g3GUE.o: In function `basic_regex': /usr/include/c++/4.5/tr1_impl/regex:771: undefined reference to `std::tr1::basic_regex<char, std::tr1::regex_traits<char> >::_M_compile()' /tmp/cc0g3GUE.o: In function `bool std::tr1::regex_match<char const*, char, std::tr1::regex_traits<char> >(char const*, char const*, std::tr1::basic_regex<char, std::tr1::regex_traits<char> > const&, std::bitset<11u>)': /usr/include/c++/4.5/tr1_impl/regex:2144: undefined reference to `bool std::tr1::regex_match<char const*, std::allocator<std::tr1::sub_match<char const*> >, char, std::tr1::regex_traits<char> >(char const*, char const*, std::tr1::match_results<char const*, std::allocator<std::tr1::sub_match<char const*> > >&, std::tr1::basic_regex<char, std::tr1::regex_traits<char> > const&, std::bitset<11u>)' collect2: ld returned 1 exit status What packages should i (un)install to make the code work on my PC?

    Read the article

  • Network share not always available on Windows 2003

    - by JP Hellemons
    Hello everybody, we have a windows 2003 server with a shared directory/folder. I've seen this thread but this wasn't any help: http://superuser.com/questions/58890/the-specified-network-name-is-no-longer-available I have a ping -t running from 3 pc's (vista and two windows 7) they all work. the problem occurss when two users enter the network share then this 'network share is no longer available' appears and the explorer windows turn white. after f5 or refresh the shared directory is back. this is really strange. there is no anti virus or kasparsky running on either end. this is all in the same LAN. the internet connection is really stable, so it's really strange. because a stable internet connection should imply that the local network connection is also stable and that this is a windows issue. can it be a router issue? I have checked the eventlog on the server for diskfailure related messages, but there are none. EDIT: can this be related to mapping a shared directory to a drive letter? and that there is a router between me and the mapped network drive? or is it just windows that is not working well with two users on the same shared folder? should I install samba or something?

    Read the article

  • Windows XP laptop doesn't appear in WSUS All computers list

    - by George
    I have this one laptop that doesn't appear in WSUS all computers list. We have about 23-25 PCs/laptops/servers in the network, all, but one are listed in WSUS. This is what I have done so far: 1) Changing Updates on local PC: Go to your Windows XP client and start a new Microsoft Management Console (MMC). At Start, Run, type MMC. Use Ctrl+M to add a new snap-in. Click Add, and then add the Group Policy Object Editor for the Local Computer. Click Close, and then click OK. Expand the Local Computer Policy. Under Computer Configuration, go to Administrative Templates, Windows Components, Windows Update. In the right-hand pane, double-click Specify intranet Microsoft update service location. Configure the settings to reflect my WSUS server. Click OK and then close the MMC without saving it. executed wuauclt.exe /detectnow 2) Edited registry key to be pushed to the PCs using GPO [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WindowsUpdate] "WUServer"=http://wsusserver "TargetGroupEnabled"=dword:00000001 "TargetGroup"="WINXP" "WUStatusServer"=http://wsuswerver 3) executed wuauclt /resetauthorization /detectnow 4)Synchronised and refreshed the group I am running out of ideas here. The client is running Windows XP pro, WSUS version is 3.0 and is running on Windows 2008 R2 64-bit. Please, help! Thanks! EDIT 13.IX.2012 @ 15.40 I should have also mentioned that we do have a Windows Update GPO for workstations group and that laptop is a part of that group.

    Read the article

< Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >