Search Results

Search found 12806 results on 513 pages for 'die 20'.

Page 402/513 | < Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >

• Dynamic DNS with Comcast

  - by colithium

  I've just recently moved across town. Previously, I had Dynamic DNS set up so I could remotely connect to my desktop (primarily to use TightVNC). My ISP was Comcast and I'm in the Denver, Colorado area. Currently, I'm still with Comcast and still in Denver. My router connects to the internet just fine and my Dynamic DNS record over at DynDNS did get updated with my router's current external IP address. So my router, DynDNS, and public DNS records all agree what my IP address is. However, I can't actually connect to anything from the outside world. My trace route to Google looks something like: Tracing route to google.com [74.125.19.147] 1 3 ms 1 ms 1 ms 192.168.1.1 (this is the internal IP address of my router) 2 * * * Request timed out. 3 9 ms 8 ms 10 ms te-8-2-ur02.wheatridge.co.denver.comcast.net [68.85.221.177] 4 12 ms 12 ms 19 ms te-0-8-0-2-ar02.aurora.co.denver.comcast.net [68.86.103.97] 5 16 ms 13 ms 11 ms pos-0-3-0-0-cr01.denver.co.ibone.comcast.net [68.86.91.1] 6 28 ms 28 ms 27 ms pos-0-9-0-0-cr01.dallas.tx.ibone.comcast.net [68.86.85.174] 7 29 ms 27 ms 28 ms pos-0-1-0-0-pe01.1950stemmons.tx.ibone.comcast.net [68.86.86.94] 8 66 ms 108 ms * 75.149.231.70 9 65 ms 68 ms 93 ms 72.14.233.77 10 67 ms 66 ms 66 ms 72.14.233.111 11 67 ms 67 ms 69 ms 216.239.43.144 12 68 ms 71 ms 73 ms 209.85.249.30 13 66 ms 66 ms 68 ms nuq04s01-in-f147.1e100.net [74.125.19.147] This is what the trace route looks like from an outside source to my DynDNS domain name: traceroute to 98.245.67.65 (98.245.67.65) 1 illuminati-130 138.67.130.61 2 138.67.63.253 138.67.63.253 3 vermiculite 138.67.253.20 4 csm-ct-gw 138.67.253.244 5 138.67.253.2 138.67.253.2 6 ge-7-24-ar01.denver.co.denver.comcast.net 68.86.128.17 7 te-0-4-0-0-ar02.denver.co.denver.comcast.net 68.86.179.21 8 te-9-3-ur01.wheatridge.co.denver.comcast.net 68.86.103.18 9 * * * {Times Out} Now my guess is, whatever is sitting just beyond my router (what the modem connects to) is gumming things up. Even though the routes aren't EXACTLY the same, that appears to be the spot that the trace route either stops or doesn't get a response. My question is, for Comcast networks (particularly in Denver), what would be the device that typically sits there? Is there anything I can do about it? That device seems to not respond to PING but does forward it along when I'm going outwards. But it looks like it eats it when the request is coming in. It's hard to prove that from these logs but I'm assuming that's the case because my router used to accept connections from the outside and I haven't changed anything on it.

  Read the article

• Blank Screen After Login on Windows 7

  - by Leigh Riffel

  When unlocking a Windows 7 computer the screen briefly (less than a second) goes blank before showing the screen. Abound once a month (but sometimes within a few days) when I unlock my computer the screen doesn't come back from this brief blackout and stays black. Sometimes after five minutes or so the display will come back. Other times it has been blank for over 20 minutes, so I give up and restart the computer. It seems to happen more often when the computer has been locked for a longer period of time - I lock my computer several times a day, but the problem most happens when I come in at the start of the day. I have updated my video card and monitor drivers. I have two monitors driven by the same graphics card. The computer is a Dell Optiplex 740. When the problem occurs both monitors have a green light on to indicate that they are receiving signal. I've tried unplugging the monitors from the video card and turning the monitors on and off. The screen saver is set to one that is not blank screen. The Windows power settings are set to never turn off the display. When the problem occurs there is no significant disk activity occurring. When the problem occurs I can connect over the network to the hard drive on my computer. When the problem occurs I can't connect over the network with a VNC connection. The VNC client doesn't give an error, but also won't show the screen. The task actually seems to hang as I can see the task, but there is no window for it. This problem occurred when I was running a pre-release version of Windows 7. The hard drive was formatted for release version and the problem still occurs. I've been stopping some of my always running programs to see if one of them may be the culprit, but given the span between failures that will take some time to find the problem if it will even help at all. Some programs I have always running include IE, Firefox, Outlook, Evernote, Kana Reminder, Ditto, Macro Express, Timesnapper, and DisplayFusion. Any ideas appreciated.

  Read the article

• Linux Mint Wireless doesn't connect

  - by guisantogui

  I'm having a great problem, I've installed Linux mint debian edition (LMDE), and following this tutorial http://community.linuxmint.com/tutorial/view/161 I did installed the network driver. The available connections appears to me, but when i try to connect to my connection at first time, I got this message: "(4) Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken." And the following tries, I got this another message: "(32) Insufficient privileges." I'm accepting ideas. Thanks. EDIT: The last piece of the logs: Oct 5 00:22:38 gsouza-host ntpd[2116]: peers refreshed Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> (wlan0): bringing up device. Oct 5 00:22:42 gsouza-host wpa_supplicant[2055]: nl80211: 'nl80211' generic netlink not found Oct 5 00:22:42 gsouza-host wpa_supplicant[2055]: Failed to initialize driver 'nl80211' Oct 5 00:22:42 gsouza-host wpa_supplicant[2055]: rfkill: WLAN soft blocked Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> WiFi hardware radio set enabled Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> WiFi now enabled by radio killswitch Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> (wlan0): supplicant interface state: starting -> ready Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> (wlan0): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42] Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> (wlan0): supplicant interface state: ready -> inactive Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <warn> Trying to remove a non-existant call id. Oct 5 00:22:42 gsouza-host wpa_supplicant[2055]: rfkill: WLAN unblocked Oct 5 00:22:44 gsouza-host avahi-daemon[1827]: Joining mDNS multicast group on interface wlan0.IPv6 with address fe80::7ae4:ff:fe4a:13a9. Oct 5 00:22:44 gsouza-host avahi-daemon[1827]: New relevant interface wlan0.IPv6 for mDNS. Oct 5 00:22:44 gsouza-host avahi-daemon[1827]: Registering new address record for fe80::7ae4:ff:fe4a:13a9 on wlan0.*. Oct 5 00:22:46 gsouza-host ntpd[2116]: Listen normally on 7 wlan0 fe80::7ae4:ff:fe4a:13a9 UDP 123 Oct 5 00:22:46 gsouza-host ntpd[2116]: peers refreshed

  Read the article

• tproxy squid bridge very slow when cache is full

  - by Roberto

  I have installed a bridge tproxy proxy in a fast server with 8GB ram. The traffic is around 60Mb/s. When I start for first time the proxy (with the cache empty) the proxy works very well but when the cache becomes full (few hours later) the bridge goes very slow, the traffic goes below 10Mb/s and the proxy server becomes unusable. Any hints of what may be happening? I'm using: linux-2.6.30.10 iptables-1.4.3.2 squid-3.1.1 compiled with these options: ./configure --prefix=/usr --mandir=/usr/share/man --infodir=/usr/share/info --datadir=/usr/share --localstatedir=/var/lib --sysconfdir=/etc/squid --libexecdir=/usr/libexec/squid --localstatedir=/var --datadir=/usr/share/squid --enable-removal-policies=lru,heap --enable-icmp --disable-ident-lookups --enable-cache-digests --enable-delay-pools --enable-arp-acl --with-pthreads --with-large-files --enable-htcp --enable-carp --enable-follow-x-forwarded-for --enable-snmp --enable-ssl --enable-async-io=32 --enable-linux-netfilter --enable-epoll --disable-poll --with-maxfd=16384 --enable-err-languages=Spanish --enable-default-err-language=Spanish My squid.conf: cache_mem 100 MB memory_pools off acl manager proto cache_object acl localhost src 127.0.0.1/32 acl localhost src ::1/128 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 acl to_localhost dst ::1/128 acl localnet src 10.0.0.0/8 # RFC1918 possible internal network acl localnet src 172.16.0.0/12 # RFC1918 possible internal network acl localnet src 192.168.0.0/16 # RFC1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl net-g1 src xxx.xxx.xxx.xxx/24 acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow net-g1 from where browsing should be allowed http_access allow localnet http_access allow localhost http_access deny all http_port 3128 http_port 3129 tproxy hierarchy_stoplist cgi-bin ? cache_dir ufs /var/spool/squid 8000 16 256 access_log none cache_log /var/log/squid/cache.log coredump_dir /var/spool/squid refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . I have this issue when the cache is full, but do not really know if it is because of that. Thanks in advance and sorry my english. roberto

  Read the article

• Hard disk problem pop up warning

  - by Leonardo

  I'm using windows 7 ultimate and it started to give me this hard disk problem warning that i had before in another OS that made me disable smart, it has been over a year since i did and my pc is running ok so my HDD is ok. all i wanna do is disable this warning that popsup while i'm gaming or doing anything else. thanks for your help :) Edit: (adding in info that was added as an answer instead of part of the question) So it's me again and i agree with both answers but i don't have the money right now to buy a new one, and yeah it could die now, i can't say. so i uploaded an image of hd tune pro scan on my HDD thanks again! anymore information would be even better, bye.

  Read the article

• How can I kill and wait for background processes to finish in a shell script when I Ctrl+C it?

  - by slipheed

  I'm trying to set up a shell script so that it runs background processes, and when I ctrl+C the shell script, it kills the children, then exits. The best that I've managed to come up with is this. It appears that kill 0 -INT also kills the script before the wait happens, so the shell script dies before the children complete. Any ideas on how I can make this shell script wait for the children to die after sending INT? #!/bin/bash trap 'killall' INT killall() { echo **** Shutting down... **** kill 0 -INT wait # Why doesn't this wait?? echo DONE } process1 & process2 & process3 & cat # wait forever

  Read the article

• Remove Downed Exchange Server from First Administrative Group

  - by Campo

  I had a server die. It is gone forever. It is still listed in the servers folder of the first administrative group in the Exchange System Manager. When I click "all tasks Remove Server" I get the following error: The Server "SERVERNAME" cannot be removed because: -One or more users currently use a mailbox on this server. These users must be moved to a mailbox store on a different server or be mail disabled before uninstalling this server. Facility: Exchange System Manager ID no: c103f492 Exchange System Manager Any help would be MUCH appreciated. I cannot access the mailbox stores anymore and I do not care about the lost mailboxes. We deleted the inactive and old users as well. So I am stumped on this one. I just need to remove the old machine. THANKS!

  Read the article

• Nginx and PHP-FPM running out of connections

  - by E3pO

  I keep running into errors like these, [02-Jun-2012 01:52:04] WARNING: [pool www] seems busy (you may need to increase pm.start_servers, or pm.min/max_spare_servers), spawning 8 children, there are 19 idle, and 49 total children [02-Jun-2012 01:52:05] WARNING: [pool www] seems busy (you may need to increase pm.start_servers, or pm.min/max_spare_servers), spawning 16 children, there are 19 idle, and 50 total children [02-Jun-2012 01:52:06] WARNING: [pool www] seems busy (you may need to increase pm.start_servers, or pm.min/max_spare_servers), spawning 32 children, there are 19 idle, and 51 total children [02-Jun-2012 03:10:51] WARNING: [pool www] seems busy (you may need to increase pm.start_servers, or pm.min/max_spare_servers), spawning 8 children, there are 18 idle, and 91 total children I changed my settings for php-fpm to these, pm.max_children = 150 (It was at 100, i got a max_children reached and upped to 150) pm.start_servers = 75 pm.min_spare_servers = 20 pm.max_spare_servers = 150 Resulting in [02-Jun-2012 01:39:19] WARNING: [pool www] server reached pm.max_children setting (150), consider raising it I've just launched a new website that is getting a conciderable amount of traffic on it. This traffic is legitimate and users are getting 504 gateway timeouts when the limit is reached. I have limited connections to my server with IPTABLES and I'm running fail2ban and keeping track of nginx access logs. The traffic is all legitimate, i'm just running out of room for users. I'm currently running on a dual core box with ubuntu 64bit. free total used free shared buffers cached Mem: 6114284 5726984 387300 0 141612 4985384 -/+ buffers/cache: 599988 5514296 Swap: 524284 5804 518480 My php.ini max_input_time = 60 My nginx config is worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 19000; # multi_accept on; } worker_rlimit_nofile 20000; #each connection needs a filehandle (or 2 if you are proxying) client_max_body_size 30M; client_body_timeout 10; client_header_timeout 10; keepalive_timeout 5 5; send_timeout 10; location ~ \.php$ { try_files $uri /er/error.php; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_connect_timeout 60; fastcgi_send_timeout 180; fastcgi_read_timeout 180; fastcgi_buffer_size 128k; fastcgi_buffers 256 16k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; fastcgi_max_temp_file_size 0; fastcgi_intercept_errors on; fastcgi_pass unix:/tmp/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } What can I do to stop running out of connections? Why does this keep occurring? I'm monitoring my traffic on Google Analytics realtime and when the user count gets above about 120 my php-fpm.log is full of these warnings..

  Read the article

• pfSense 2.1 OpenVPN client not using tunnelled interface

  - by Brian M. Hunt

  I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

  Read the article

• JNDI Datasource Problem on Tomcat 6, Hibernate

  - by Asuman AKYILDIZ

  I am using Tomcat 6 as application server, Struts-Hibernate and MyEclipse 6.0. My application uses JDBC driver but I should modify it to use JNDI Datasource. I followed steps as described in tomcat 6.0 howto tutorial. I defined my resource in tomcatconf: <Resource name="jdbc/ats" global="jdbc/ats" auth="Container" type="javax.sql.DataSource" driverClassName="oracle.jdbc.OracleDriver" url="jdbc:oracle:thin:@//localhost:1521/MISDEV" username="TEST" password="TEST" maxActive="20" maxIdle="10" maxWait="-1" validationQuery="SELECT 1 from dual" removeAbandoned="true" removeAbandonedTimeout="30" logAbandoned="false"/> I gave reference in my application web.xml: <resource-ref> <description>Oracle Datasource example</description> <res-ref-name>jdbc/ats</res-ref-name> <res-type>javax.sql.DataSource</res-type> <res-auth>Container</res-auth> </resource-ref> And I defined datasource-dialect in my hibernate-cfg.xml <property name="connection.datasource">java:comp/env/jdbc/ats</property> <property name="dialect">org.hibernate.dialect.Oracle9Dialect</property> But when I create hibernate session, it can not open the connection: 09:18:11,322 ERROR JDBCExceptionReporter:72 - Connections could not be acquired from the underlying database! org.hibernate.exception.GenericJDBCException: Cannot open connection I also tried to set the properties at runtime: Configuration configuration = new Configuration(); configuration.setProperty("hibernate.dialect", "org.hibernate.dialect.Oracle9Dialect"); //configuration.setProperty("hibernate.connection.datasource", "java:comp/env/jdbc/ats"); configuration.setProperty("hibernate.current_session_context_class", "thread"); configuration.setProperty("hibernate.connection.provider_class", "org.hibernate.connection.C3P0ConnectionProvider"); configuration.setProperty("hibernate.show_sql", "true"); sessionFactory = configuration.configure().buildSessionFactory(); It does not open connection again. But, when I use JDBC driver it works: Configuration configuration = new Configuration(); configuration.setProperty("hibernate.dialect", "org.hibernate.dialect.Oracle9Dialect"); //configuration.setProperty("hibernate.connection.datasource", "java:comp/env/jdbc/ats"); configuration.setProperty("hibernate.connection.url", "jdbc:oracle:thin:@//localhost:1521/MISDEV"); configuration.setProperty("hibernate.connection.username", "test"); configuration.setProperty("hibernate.connection.password", "test"); configuration.setProperty("hibernate.connection.driver_class", "oracle.jdbc.OracleDriver"); configuration.setProperty("hibernate.transaction.factory_class", "org.hibernate.transaction.JDBCTransactionFactory"); configuration.setProperty("hibernate.current_session_context_class", "thread"); configuration.setProperty("hibernate.connection.provider_class", "org.hibernate.connection.C3P0ConnectionProvider"); configuration.setProperty("hibernate.show_sql", "true"); sessionFactory = configuration.configure().buildSessionFactory(); I have been searching for 3 days and no success. What may be de problem?

  Read the article

• High Server Load cannot figure out why

  - by Tim Bolton

  My server is currently running CentOS 5.2, with WHM 11.34. Currently, we're at 6.43 to 12 for a load average. The sites that we're hosting are taking a lot time to respond and resolve. top doesn't show anything out of the ordinary and iftop doesn't show a lot of traffic. We have many resellers, and some not so good at writing code, how can we find the culprit? vmstat output: vmstat procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 0 2 84 78684 154916 1021080 0 0 72 274 0 14 6 3 80 12 0 top output (ordered by %CPU) top - 21:44:43 up 5 days, 10:39, 3 users, load average: 3.36, 4.18, 4.73 Tasks: 222 total, 3 running, 219 sleeping, 0 stopped, 0 zombie Cpu(s): 5.8%us, 2.3%sy, 0.2%ni, 79.6%id, 11.8%wa, 0.0%hi, 0.2%si, 0.0%st Mem: 2074580k total, 1863044k used, 211536k free, 174828k buffers Swap: 2040212k total, 84k used, 2040128k free, 987604k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 15930 mysql 15 0 138m 46m 4380 S 4 2.3 1:45.87 mysqld 21772 igniteth 17 0 23200 7152 3932 R 4 0.3 0:00.02 php 1586 root 10 -5 0 0 0 S 2 0.0 11:45.19 kjournald 21759 root 15 0 2416 1024 732 R 2 0.0 0:00.01 top 1 root 15 0 2156 648 560 S 0 0.0 0:26.31 init 2 root RT 0 0 0 0 S 0 0.0 0:00.35 migration/0 3 root 34 19 0 0 0 S 0 0.0 0:00.32 ksoftirqd/0 4 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 5 root RT 0 0 0 0 S 0 0.0 0:02.00 migration/1 6 root 34 19 0 0 0 S 0 0.0 0:00.11 ksoftirqd/1 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/1 8 root RT 0 0 0 0 S 0 0.0 0:01.29 migration/2 9 root 34 19 0 0 0 S 0 0.0 0:00.26 ksoftirqd/2 10 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/2 11 root RT 0 0 0 0 S 0 0.0 0:00.90 migration/3 12 root 34 19 0 0 0 R 0 0.0 0:00.20 ksoftirqd/3 13 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/3 top output (ordered by CPU time) top - 21:46:12 up 5 days, 10:41, 3 users, load average: 2.88, 3.82, 4.55 Tasks: 217 total, 1 running, 216 sleeping, 0 stopped, 0 zombie Cpu(s): 3.7%us, 2.0%sy, 2.0%ni, 67.2%id, 25.0%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 2074580k total, 1959516k used, 115064k free, 183116k buffers Swap: 2040212k total, 84k used, 2040128k free, 1090308k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ TIME COMMAND 32367 root 16 0 215m 212m 1548 S 0 10.5 62:03.63 62:03 tailwatchd 1586 root 10 -5 0 0 0 S 0 0.0 11:45.27 11:45 kjournald 1576 root 10 -5 0 0 0 S 0 0.0 2:37.86 2:37 kjournald 27722 root 16 0 2556 1184 800 S 0 0.1 1:48.94 1:48 top 15930 mysql 15 0 138m 46m 4380 S 4 2.3 1:48.63 1:48 mysqld 2932 root 34 19 0 0 0 S 0 0.0 1:41.05 1:41 kipmi0 226 root 10 -5 0 0 0 S 0 0.0 1:34.33 1:34 kswapd0 2671 named 25 0 74688 7400 2116 S 0 0.4 1:23.58 1:23 named 3229 root 15 0 10300 3348 2724 S 0 0.2 0:40.85 0:40 sshd 1580 root 10 -5 0 0 0 S 0 0.0 0:30.62 0:30 kjournald 1 root 17 0 2156 648 560 S 0 0.0 0:26.32 0:26 init 2616 root 15 0 1816 576 480 S 0 0.0 0:23.50 0:23 syslogd 1584 root 10 -5 0 0 0 S 0 0.0 0:18.67 0:18 kjournald 4342 root 34 19 27692 11m 2116 S 0 0.5 0:18.23 0:18 yum-updatesd 8044 bollingp 15 0 3456 2036 740 S 1 0.1 0:15.56 0:15 imapd 26 root 10 -5 0 0 0 S 0 0.0 0:14.18 0:14 kblockd/1 7989 gmailsit 16 0 3196 1748 736 S 0 0.1 0:10.43 0:10 imapd iostat -xtk 1 10 output [root@server1 tmp]# iostat -xtk 1 10 Linux 2.6.18-53.el5 12/18/2012 Time: 09:51:06 PM avg-cpu: %user %nice %system %iowait %steal %idle 5.83 0.19 2.53 11.85 0.00 79.60 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 1.37 118.83 18.70 54.27 131.47 692.72 22.59 4.90 67.19 3.10 22.59 sdb 0.35 39.33 20.33 61.43 158.79 403.22 13.75 5.23 63.93 3.77 30.80 Time: 09:51:07 PM avg-cpu: %user %nice %system %iowait %steal %idle 1.50 0.00 0.50 24.00 0.00 74.00 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 25.00 2.00 2.00 128.00 108.00 118.00 0.03 7.25 4.00 1.60 sdb 0.00 16.00 41.00 145.00 200.00 668.00 9.33 107.92 272.72 5.38 100.10 Time: 09:51:08 PM avg-cpu: %user %nice %system %iowait %steal %idle 2.00 0.00 1.50 29.50 0.00 67.00 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 95.00 3.00 33.00 12.00 480.00 27.33 0.07 1.72 1.31 4.70 sdb 0.00 14.00 1.00 228.00 4.00 960.00 8.42 143.49 568.01 4.37 100.10 Time: 09:51:09 PM avg-cpu: %user %nice %system %iowait %steal %idle 13.28 0.00 2.76 21.30 0.00 62.66 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 21.00 1.00 19.00 16.00 192.00 20.80 0.06 3.55 1.30 2.60 sdb 0.00 36.00 28.00 181.00 124.00 884.00 9.65 121.16 617.31 4.79 100.10 Time: 09:51:10 PM avg-cpu: %user %nice %system %iowait %steal %idle 4.74 0.00 1.50 25.19 0.00 68.58 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 20.00 3.00 15.00 12.00 136.00 16.44 0.17 7.11 3.11 5.60 sdb 0.00 0.00 103.00 60.00 544.00 248.00 9.72 52.35 545.23 6.14 100.10 Time: 09:51:11 PM avg-cpu: %user %nice %system %iowait %steal %idle 1.24 0.00 1.24 25.31 0.00 72.21 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 75.00 4.00 28.00 16.00 416.00 27.00 0.08 3.72 2.03 6.50 sdb 2.00 9.00 124.00 17.00 616.00 104.00 10.21 3.73 213.73 7.10 100.10 Time: 09:51:12 PM avg-cpu: %user %nice %system %iowait %steal %idle 1.00 0.00 0.75 24.31 0.00 73.93 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 24.00 1.00 9.00 4.00 132.00 27.20 0.01 1.20 1.10 1.10 sdb 4.00 40.00 103.00 48.00 528.00 212.00 9.80 105.21 104.32 6.64 100.20 Time: 09:51:13 PM avg-cpu: %user %nice %system %iowait %steal %idle 2.50 0.00 1.75 23.25 0.00 72.50 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 125.74 3.96 46.53 15.84 689.11 27.92 0.20 4.06 2.41 12.18 sdb 2.97 0.00 91.09 84.16 419.80 471.29 10.17 85.85 590.78 5.66 99.11 Time: 09:51:14 PM avg-cpu: %user %nice %system %iowait %steal %idle 0.75 0.00 0.50 24.94 0.00 73.82 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 88.00 1.00 7.00 4.00 380.00 96.00 0.04 4.38 3.00 2.40 sdb 3.00 7.00 111.00 44.00 540.00 208.00 9.65 18.58 581.79 6.46 100.10 Time: 09:51:15 PM avg-cpu: %user %nice %system %iowait %steal %idle 11.03 0.00 3.26 26.57 0.00 59.15 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 145.00 7.00 53.00 28.00 792.00 27.33 0.15 2.50 1.55 9.30 sdb 1.00 0.00 155.00 0.00 800.00 0.00 10.32 2.85 18.63 6.46 100.10 [root@server1 tmp]# MySQL Show Full Processlist mysql> show full processlist; +------+---------------+-----------+-----------------------+----------------+------+----------------------------+----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ | Id | User | Host | db | Command | Time | State | Info | +------+---------------+-----------+-----------------------+----------------+------+----------------------------+----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ | 1 | DB_USER_ONE | localhost | DB_ONE | Query | 3 | waiting for handler insert | INSERT DELAYED INTO defers (mailtime,msgid,email,transport_method,message,host,ip,router,deliveryuser,deliverydomain) VALUES(FROM_UNIXTIME('1355879748'),'1TivwL-0003y8-8l','[email protected]','remote_smtp','SMTP error from remote mail server after initial connection: host mx1.mail.tw.yahoo.com [203.188.197.119]: 421 4.7.0 [TS01] Messages from 75.125.90.146 temporarily deferred due to user complaints - 4.16.55.1; see http://postmaster.yahoo.com/421-ts01.html','mx1.mail.tw.yahoo.com','203.188.197.119','lookuphost','','') | | 2 | DELAYED | localhost | DB_ONE | Delayed insert | 52 | insert | | | 3 | DELAYED | localhost | DB_ONE | Delayed insert | 68 | insert | | | 911 | DELAYED | localhost | DB_ONE | Delayed insert | 99 | Waiting for INSERT | | | 993 | DB_USER_TWO | localhost | DB_TWO | Sleep | 832 | | NULL | | 994 | DB_USER_ONE | localhost | DB_ONE | Query | 185 | Locked | delete from failures where FROM_UNIXTIME(UNIX_TIMESTAMP(NOW())-1296000) > mailtime | | 1102 | DB_USER_THREE | localhost | DB_THREE | Query | 29 | NULL | commit | | 1249 | DB_USER_FOUR | localhost | DB_FOUR | Query | 13 | NULL | commit | | 1263 | root | localhost | DB_FIVE | Query | 0 | NULL | show full processlist | | 1264 | DB_USER_SIX | localhost | DB_SIX | Query | 3 | NULL | commit | +------+---------------+-----------+-----------------------+----------------+------+----------------------------+----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+ 10 rows in set (0.00 sec)

  Read the article

• MD3200 - 3 to 4x less throughput than MD1220. Am I missing something here?

  - by Igor Polishchuk

  I have two R710 servers with similar configuration. One in my office has MD1220 attached. Another one in the datacenter of my hosting services vendor has MD3200. I'm getting significantly worse throughput from MD3200 at my vendors setup. I'm mostly interested in sequential writes, and I'm getting these results in bonnie++ and dd tests: Seq. writes on MD1220 in my office: 1.1 GB/s - bonnie++, 1.3GB/s - dd Seq. writes on MD3200 at my vendor's: 240MB/s - bonnie++, 310MB/s - dd Unfortunately, I could not test the exactly the same configurations, but the two I have should be comparable. If anything, my good performing environment is cheaper than the bad performing. I expect at least similar throughput from these two setups. My vendor cannot really help me. Hopefully, somebody more familiar with the DAS performance can look at it and tell if I'm missing something here and my expectations are too high. To summarize, the question here is it reasonable to expect about 100MB/s of sequential write throughput per each couple of drives in RAID10 on MD3200? Is there any trick to enable such performance in MD3200 with dual controller as opposed to simple MD1220 with a single H800 adapter? More details about the configurations: A good one in my office: Dell R710 2CPU X5650 @ 2.67GHz 12 cores 96GB DDR3, OS: RHEL 5.5, kernel 2.6.18-194.26.1.el5 x86_64 20x300GB 2.5" SAS 10K in a single RAID10 1MB chunk size on MD1220 + Dell H800 I/O controller with 1GB cache in the host Not so good one at my vendor's: Dell R710 2CPU L5520 @ 2.27GHz 8 cores 144GB DDR3, OS: RHEL 5.5, kernel 2.6.18-194.11.4.el5 x86_64 20x146GB 2.5" SAS 15K in a single RAID10 512KB chunk size, Dell MD3200, 2 I/O controllers in array with 1GB cache each Additional information. I've also ran the same tests on the same vendor's host, but the storage was: two raids of 14x146GB 15K RPM drives RAID 10, striped together on the OS level on MD3000+MD1000. The performance was about 25% worse than on MD3200 despite having more drives. When I ran similar tests on the internal storage of my vendor's host (2x146GB 15K RPM drives RAID1, Perc 6i) I've got about 128MB/s seq. writes. Just two internal drives gave me about a half of 20 drives' throughput on MD3200. The random I/O performance of the MD3200 setup is ok, it gives me at least 1300 IOPS. I'm mostly have problems with sequentioal I/O throughput. Thank you for looking into it. Regards Igor

  Read the article

• Apache2 & .htaccess : Apache ignoring AccessFile

  - by Elyx0

  Hi there here is my server configuration: DEBIAN 32Bits / PHP 5 / Apache Server version: Apache/2.2.3 - Server built: Mar 22 2008 09:29:10 The AccessFiles : grep -ni AccessFileName * apache2.conf:134:AccessFileName .htaccess apache2.conf:667:AccessFileName .httpdoverride All the AllowOverride statements in my apache2/ folder. mods-available/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-available/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit mods-enabled/userdir.conf:6: AllowOverride Indexes AuthConfig Limit mods-enabled/userdir.conf:16: AllowOverride FileInfo AuthConfig Limit sites-enabled/default:8: AllowOverride All sites-enabled/default:14: AllowOverride All sites-enabled/default:19: AllowOverride All sites-enabled/default:24: AllowOverride All sites-enabled/default:42: AllowOverride All The sites-enabled/default file : 1 <VirtualHost *> 2 ServerAdmin [email protected] 3 ServerName mysite.com 4 ServerAlias mysite.com 5 DocumentRoot /var/www/mysite.com/ 6 <Directory /> 7 Options FollowSymLinks 8 AllowOverride All 9 Order Deny,Allow 10 Deny from all 11 </Directory> 12 <Directory /var/www/mysite.com/> 13 Options Indexes FollowSymLinks MultiViews 14 AllowOverride All 15 Order allow,deny 16 allow from all 17 </Directory> 18 <Directory /var/www/mysite.com/test/> 19 AllowOverride All 20 </Directory> 21 22 ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ 23 <Directory "/usr/lib/cgi-bin"> 24 AllowOverride All 25 Options ExecCGI -MultiViews +SymLinksIfOwnerMatch 26 Order allow,deny 27 Allow from all 28 </Directory> 29 30 ErrorLog /var/log/apache2/error.log 31 32 # Possible values include: debug, info, notice, warn, error, crit, 33 # alert, emerg. 34 LogLevel warn 35 36 CustomLog /var/log/apache2/access.log combined 37 ServerSignature Off 38 39 Alias /doc/ "/usr/share/doc/" 40 <Directory "/usr/share/doc/"> 41 Options Indexes MultiViews FollowSymLinks 42 AllowOverride All 43 Order deny,allow 44 Deny from all 45 Allow from 127.0.0.0/255.0.0.0 ::1/128 46 </Directory> 47 48 49 50 51 52 53 54 </VirtualHost> If i change any Allow from all in Deny from all , it works whenever i put it. I've got one .htaccess at /mysite.com/.htaccess & one at /mysite.com/test/.htaccess with: Order Deny,Allow Deny from all Neither of them work i can still see my website. I've got mod_rewrite enabled but i don't think it does anything here. I've tried almost everything :/ It works on my local environnement (MAMP) but fails when on my Debian server.

  Read the article

• Issues with Server 2012 using DFSR running on Hyper-V 2012

  - by Bryan

  We have a number of Server 2012 systems, all of which run virtualised on Hyper-V 2012 server. We are having problems with two such virtual instances, both of which are used as file servers, whereby they occasionally stop responding to requests to serve files to clients. After logging on to the server, attempts to shut it down gracefully fail (no error, it just fails to acknowledge a shutdown request). Recovery is a case of power cycling the server(s) from the Hyper-V console. These two servers don't server a large number of users (one serves no more than 6 users, and the other serves around 20 users), they are in the same domain, but on different physical hardware (and at different sites). They don't lock up at the same time. They both use DFSR to replicate a fairly large amount of data between themselves (200GB) over ADSL connections, this is working fine, and we have been using DFSR to do this on the previous two generations of server OS we have used (Server 2008 R2 and Server 2003 - both of which were physical installs however). Today, when one of the servers crashed, I noticed an entry in the event log, which looked similar to the following: Log Name: Application Source: ESENT Date: 27/11/2012 10:25:55 Event ID: 533 Task Category: General Level: Warning Keywords: Classic User: N/A Computer: HAL-FS-01.example.com Description: DFSRs (1500) \\.\E:\System Volume Information\DFSR\database_C8CC_101_CC00_EC0E\ dfsr.db: A request to write to the file "\\.\E:\System Volume Information\ DFSR\database_C8CC_101_CC00_EC0E\fsr.log" at offset 4423680 (0x0000000000438000) for 4096 (0x00001000) bytes has not completed for 36 second(s). This problem is likely due to faulty hardware. Please contact your hardware vendor for further assistance diagnosing the problem. When the server started up again, I went to find the event log entry to investigate further and found that the event log entry was no longer there (I assume it was in memory but failed to write to disk before the server was powered off, for the reason mentioned in the message). I found the above message by searching back further in the event log. Both of these virtual servers have their E: volumes fully allocated as opposed to dynamically expanding, and there are no other issues on any of the other virtual servers (which include server 2012, server 2008 R2 and Ubuntu 12.04 x64). There are no signs of IO, memory or CPU starvation on the host systems. I've used performance counters on the affected virtual servers to monitor memory usage (including non paged pool usage), as well as CPU and network utilisation, and none of these show any signs of trouble when the issue arises. I would have thought our configuration isn't that uncommon, so I'm wondering if anyone else has seen this, and managed to resolve the problem?

  Read the article

• systemd initiated uwsgi process shuts down after a while

  - by Calvin Cheng

  So I wrote this simple systemd service script:- [Unit] Description=uwsgi server script [Service] User=web Group=web WorkingDirectory=/var/www/prod/myproject/releases/current ExecStart=/bin/bash -c 'source ~/.bash_profile; workon myproject; uwsgi --ini /var/www/prod/myproject/releases/current/myproject/uwsgi_prod.ini' [Install] WantedBy=multi-user.target which works fine - it starts up and I can see my uwsgi processes in htop. However, it inexplicably shuts down after being idle for 5 minutes. If I start this process manually in bash console by executing, as web user:- source ~/.bash_profile workon myproject uwsgi --ini /var/www/prod/myproject/releases/current/myproject/uwsgi_prod.ini my process does not die after being idle. What could the problem be?

  Read the article

• Low framerate on background apps

  - by user1698923

  My problem is that when a game is running in the foreground, in Full Screen mode, any applications on my second monitor (such as youtube videos, videos, not app specific) drop their frame-rate to about 2-3 FPS. It seems like some sort of power management option that I can't track down. As far as I can tell, it's not due to the GPU not being able to keep up. For instance, my PC can play League of Legends at about 280FPS when the framerate is uncapped. If i cap it at 60FPS using the in-game option, it has no affect on the performance of the background app. Summary Operating System Windows 8 Pro 64-bit CPU Intel Core i7 3820 @ 3.60GHz 42 °C Sandy Bridge-E 32nm Technology RAM 12.0GB Triple-Channel DDR3 @ 533MHz (7-7-7-20) Motherboard Gigabyte Technology Co., Ltd. X79-UD3 (SOCKET 0) 37 °C Graphics DELL U2713HM (2560x1440@59Hz) DELL U2713HM (2560x1440@59Hz) 1280MB NVIDIA GeForce GTX 570 (Gigabyte) 58 °C Hard Drives 212GB Volume0 (RAID) 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 36 °C 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 34 °C Optical Drives No optical disk drives detected Audio ASUS Xonar Essence STX Audio Device Operating System Windows 8 Pro 64-bit Computer type: Desktop Graphics Monitor 1 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Secondary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY4\Monitor0 Monitor 2 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Primary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY5\Monitor0 NVIDIA GeForce GTX 570 Manufacturer NVIDIA Model GeForce GTX 570 GPU GF110 Device ID 10DE-1086 Revision A2 Subvendor Gigabyte (1458) Series GeForce GTX 500 Current Performance Level Level 3 Current GPU Clock 845 MHz Current Memory Clock 1900 MHz Current Shader Clock 1690 MHz Voltage 0.988 V Technology 40 nm Die Size 520 mm² Release Date Dec 07, 2010 DirectX Support 11.0 OpenGL Support 5.0 Bus Interface PCI Express x16 Temperature 57 °C Driver version 9.18.13.2018 BIOS Version 70.10.55.00.01 ROPs 40 Shaders 512 unified Memory Type GDDR5 Memory 1280 MB Bus Width 64x5 (320 bit) Filtering Modes 16x Anisotropic Noise Level Moderate Max Power Draw 219 Watts Count of performance levels : 3 Level 1 - "Default" GPU Clock 50 MHz Memory Clock 135 MHz Shader Clock 101 MHz Level 2 - "2D Desktop" GPU Clock 405 MHz Memory Clock 324 MHz Shader Clock 810 MHz Level 3 - "3D Applications" GPU Clock 845 MHz Memory Clock 1900 MHz Shader Clock 1690 MHz Things I've tried: 1) Updating the graphics driver 2) Setting windows power mode to High Performance 3) Reset Nvidia Global Performance settings to default

  Read the article

• libvirt qemu/kvm migration problem

  - by Panda

  I am using kvm and libvirt on my Dell server. Now i am trying to migrate one virtual machine from a physical server to another. However, I failed everytime. In virsh on physicalServer1, I typed: virsh # migrate virtualmachine1 qemu+ssh://username@physicalServer2/system error: operation failed: migration to 'tcp:physicalServer2:49163' failed: migration failed Then I searched FAQ part on libvirt.org. It says: error: operation failed: migration to '...' failed: migration failed This is an error often encountered when trying to migrate with QEMU/KVM. This typically happens with plain migration, when the source VM cannot connect to the destination host. You will want to make sure your hosts are properly configured for migration (see the migration section of this FAQ) I managed to ssh physicalServer2 from a shell on virtualmachine1 so the above red part did not explain my failure. I also open ports on physicalServer2, iptables -L shows following information: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT tcp -- anywhere anywhere state NEW tcp dpts:49152:49215 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer2: 2011-05-06 13:37:30.708: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.14 -enable-kvm -m 2048 -smp 1,sockets=1,cores=1,threads=1 -name openjudge-test -uuid a8c704bc-a4f9-90db-3e57-40e60b00aac1 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/virtualmachine1.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=readline -rtc base=utc -boot c -drive file=/media/nfs/virtualmachine1.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=00:16:36:8a:22 :a0,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:2 -vga cirrus -incoming tcp:0.0.0.0:49163 -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/0 2011-05-06 13:37:30.915: shutting down The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer1 is empty. Both physical servers are using Ubuntu 11.04. The libvirt and kvm used are installed by apt-get. The libvirt version is 0.8.8.

  Read the article

• How to customize Windows Failover clustering to trigger on failure of custom window service?

  - by melaos

  i'm a total newbie on windows failover clustering. and what i want to do now is to setup the FC (failover clustering) on two win 2008 R2 server. and right now i have my custom window service running on both machine. But they cannot run concurrently as it will mess up the DB, thus i just want one to be available at all time (high availability). so i'm wondering if there's any way to set the failover policy to include this custom window service that i've installed on these machines so that if this service goes down or die, then it will automatically trigger the failover to the second node. is this possible? or must it be done programatically? and if so what is the best way? thanks ~m

  Read the article

• Passwords and Keys in Linux

  - by PeanutsMonkey

  In a fit of desperation when I had my wireless connection die on me, I thought it was a problem with the key I had created at the start when I initially configured the wireless connection and hence deleted it. The option to create the key had presented itself when I created the wireless connection. It no longer asks me to. Now I am back online, do I have re-create the password and key I had before? If so, what do I choose and why? The options I have are as follows; PGP Stored password Password keyring Secure shell key The first and last option seem to be obvious and I have no idea about the differences between the second and third options. Why do I need a stored password or password keyring in all scenarios and not just the wireless issue I ran into? EDIT 0 Further to Belisama's comment, I have amended my question. EDIT 1 As requested, I have attached a screenshot

  Read the article

• Uninstall last n of ports/packages

  - by Radio

  While compiling some port, I realized that it depends on 1000+ of other ports and will install forever until I die or my disk is full (my hdd is really small). I interrupted make install clean. How do I uninstall and clean those dependencies which have already been built and installed? (there are at least 100+ of them) pkg_cutleaves wont work in this case, since the main port wasn't registered yet. Please help. FreeBSD 9.0-RELEASE amd64 EDIT: Another way to ask this question: How can I see all dependencies for a non-registered port, and all subdependencies for those dependencies, independent with previously installed ports or their [sub]dependencies?

  Read the article

• Django + gunicorn + virtualenv + Supervisord issue

  - by Florian Le Goff

  Dear all, I have a strange issue with my virtualenv + gunicorn setup, only when gunicorn is launched via supervisord. I do realize that it may very well be an issue with my supervisord and I would appreciate any feedback on a better place to ask for help... In a nutshell : when I run gunicorn from my user shell, inside my virtualenv, everything is working flawlessly. I'm able to access all the views of my Django project. When gunicorn is launched by supervisord at the system startup, everything is OK. But, if I have to kill the gunicorn_django processes, or if I perform a supervisord restart, once that gunicorn_django has relaunched, every request is answered with a weird Traceback : (...) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/__init__.py", line 77, in connection = connections[DEFAULT_DB_ALIAS] File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 92, in __getitem__ backend = load_backend(db['ENGINE']) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 50, in load_backend raise ImproperlyConfigured(error_msg) TemplateSyntaxError: Caught ImproperlyConfigured while rendering: 'django.db.backends.postgresql_psycopg2' isn't an available database backend. Try using django.db.backends.XXX, where XXX is one of: 'dummy', 'mysql', 'oracle', 'postgresql', 'postgresql_psycopg2', 'sqlite3' Error was: cannot import name utils Full stack available here : http://pastebin.com/BJ5tNQ2N I'm running... Ubuntu/maverick (up-to-date) Python = 2.6.6 virtualenv = 1.5.1 gunicorn = 0.12.0 Django = 1.2.5 psycopg2 = '2.4-beta2 (dt dec pq3 ext)' gunicorn configuration : backlog = 2048 bind = "127.0.0.1:8000" pidfile = "/tmp/gunicorn-hc.pid" daemon = True debug = True workers = 3 logfile = "/home/hc/prod/log/gunicorn.log" loglevel = "info" supervisord configuration : [program:gunicorn] directory=/home/hc/prod/hc command=/home/hc/prod/venv/bin/gunicorn_django -c /home/hc/prod/hc/gunicorn.conf.py user=hc umask=022 autostart=True autorestart=True redirect_stderr=True Any advice ? I've been stuck on this one for quite a while. It seems like some weird memory limit, as I'm not enforcing anything special : $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 20 file size (blocks, -f) unlimited pending signals (-i) 16382 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited Thank you.

  Read the article

• OS X Snow Leopard 10.6 Refuses to Load Websites the first time intermittently

  - by Brandon

  Many times when I am browsing the web, Snow Leopard will sit and load a site for 20 seconds or more, until it times out and says it cannot be displayed. If I refresh, it loads RIGHT away, every time. The issue is intermittent but happens from once every couple of days to a few times a day. So the long and short of it is this: Aluminum MacBook (Non-Pro) 2.4GHz Core2Duo, 4GB DDR3 I am using 10.6.6 but I have had this issue since 10.6.0 It happens in Firefox, Chrome, and Safari I have flushed my DNS (using the command 'blablabla flush') I am using custom DNS servers which I hoped would fix it but it had no effect* I am running Apache currently but haven't been for most of the time I've reformatted multiple times, always experiencing the issue I am on Cox cable internet, with a Motorola Surfboard & a Belkin F6D4230-4 v1 (Pre?) N wireless router. I've put the router in G only & N only & G+N to no effect It seems to be domain dependant as I can sometimes load the Google cache right away, and sometimes other sites will load but Google will refuse My Powerbook G4 with Leopard, other Windows XP laptops, & my wired Win7 desktop do not suffer from the issue. *I recently started using these to escape the awful Cox redirect page on timeouts I'm almost positive the issue has happened on other networks but I can't recall a specific instance (I have a terrible memory). The problem is intermittent and fixable enough (I just have to wait until it times out and hit refresh one time) but incredibly annoying since I'm constantly reading documentation from a large variety of sites. EDIT: To clarify, this happens with ALL sites, not only specific sites. I haven't been able to detect any pattern to the failures, but one day Google.com will refuse to load while reddit.com will, and the next day vice versa. Keep in mind that waiting for a timeout and hitting refresh loads the page right away, every time. If I don't wait for the timeout, opening more links, hitting refresh, and clicking the link a billion times have no effect. It seems to be domain neutral, affecting sites seemingly at random. It doesn't seem to have anything to do with connection inactivity either, because I will be SSHed into different servers, uploading files, browsing, downloading, etc, and it will just quit loading Jquery.com (for example) until I sit and wait for a timeout. /EDIT This is my last resort. Please, someone, tell me what is happening. Thank you.

  Read the article

• How do I protect a low budget network from rogue DHCP servers?

  - by Kenned

  I am helping a friend manage a shared internet connection in an apartment buildling with 80 apartments - 8 stairways with 10 apartments in each. The network is laid out with the internet router at one end of the building, connected to a cheap non-managed 16 port switch in the first stairway where the first 10 apartments are also connected. One port is connected to another 16 port cheapo switch in the next stairway, where those 10 apartments are connected, and so forth. Sort of a daisy chain of switches, with 10 apartments as spokes on each "daisy". The building is a U-shape, approximately 50 x 50 meters, 20 meters high - so from the router to the farthest apartment it’s probably around 200 meters including up-and-down stairways. We have a fair bit of problems with people hooking up wifi-routers the wrong way, creating rogue DHCP servers which interrupt large groups of the users and we wish to solve this problem by making the network smarter (instead of doing a physical unplugging binary search). With my limited networking skills, I see two ways - DHCP-snooping or splitting the entire network into separate VLANS for each apartment. Separate VLANS gives each apartment their own private connection to the router, while DHCP snooping will still allow LAN gaming and file sharing. Will DHCP snooping work with this kind of network topology, or does that rely on the network being in a proper hub-and-spoke-configuration? I am not sure if there are different levels of DHCP snooping - say like expensive Cisco switches will do anything, but inexpensive ones like TP-Link, D-Link or Netgear will only do it in certain topologies? And will basic VLAN support be good enough for this topology? I guess even cheap managed switches can tag traffic from each port with it’s own VLAN tag, but when the next switch in the daisy chain receives the packet on it’s “downlink” port, wouldn’t it strip or replace the VLAN tag with it’s own trunk-tag (or whatever the name is for the backbone traffic). Money is tight, and I don’t think we can afford professional grade Cisco (I have been campaigning for this for years), so I’d love some advice on which solution has the best support on low-end network equipment and if there are some specific models that are recommended? For instance low-end HP switches or even budget brands like TP-Link, D-Link etc. If I have overlooked another way to solve this problem it is due to my lack of knowledge. :)

  Read the article

• Macbook shuts down when battery is empty (should have went to sleep)

  - by the_great_monkey

  In the past few weeks, my macbook shuts down when the battery dies. The battery does not even die at 0%, sometimes it shuts down at 5% or 10% remaining. I tried calibrating the baterry following this website: http://support.apple.com/kb/HT1490. But it does not really help. I regularly use battery in my macbook, I'd say I use around 2-3 cycles a week. My charge cycles is 440 cycles, and my current battery capacity is 3400mAh from the original 4100mAh. I have 2008 unibody Macbook. Does anyone know how to make it goes to sleep before the battery's dead? EDIT: The OS seems the think that the battery is ok...

  Read the article

• Globe SSL with NGINX SSL certificate problem, please help

  - by PartySoft

  Hello, I have a big problem with installing a certificat for nginx (same happends with apache though) I have 3 files __domain_com.crt __domain_com.ca-bundle and ssl.key. I tried to append cat __domain_com.crt __leechpack_com.ca-bundle bundle.crt but if I do it like this i get an error: [emerg]: SSL_CTX_use_certificate_chain_file("/etc/nginx/__leechpack_com.crt") failed (SSL: error:0906D066:PEM routines:PEM_read_bio:bad end line error:140DC009:SSL routines:SSL_CTX_use_certificate_chain_file:PEM lib) And that's because the delimiters of the certificates arren't separated. ZqTjb+WBJQ== -----END CERTIFICATE----------BEGIN CERTIFICATE----- MIIE6DCCA9CgAwIBAgIQdIYhlpUQySkmKUvMi/gpLDANBgkqhkiG9w0BAQUFADBv If i separate them with an enter between certificated it will at least start but i will get the same warning from Firefox: This Connection is Untrusted You have asked Firefox to connect securely to domain.com, but we can't confirm that your connection is secure. The concatenate solution it is given by Globe SSL and the NGINX site but it doesn't work. I think the bundle is ignored though. http://customer.globessl.com/knowledgebase/55/Certificate-Installation--Nginx.html http://nginx.org/en/docs/http/configuring_https_servers.html#chains%20http://wiki.nginx.org/NginxHttpSslModule if i do openssl s_client -connect down.leechpack.com:443 CONNECTED(00000003) depth=0 /OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com verify error:num=20:unable to get local issuer certificate verify return:1 depth=0 /OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com verify error:num=27:certificate not trusted verify return:1 depth=0 /OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com verify error:num=21:unable to verify the first certificate verify return:1 --- Certificate chain 0 s:/OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com i:/C=RO/O=GLOBE HOSTING CERTIFICATION AUTHORITY/CN=GLOBE SSL Domain Validated CA 1 s:/C=US/O=Globe Hosting, Inc./OU=GlobeSSL DV Certification Authority/CN=GlobeSSL CA i:/C=SE/O=AddTrust AB/OU=AddTrust External TTP Network/CN=AddTrust External CA Root --- Server certificate -----BEGIN CERTIFICATE----- MIIFQzCCBCugAwIBAgIQRnpCmtwX7z7GTla0QktE6DANBgkqhkiG9w0BAQUFADBl MQswCQYDVQQGEwJSTzEuMCwGA1UEChMlR0xPQkUgSE9TVElORyBDRVJUSUZJQ0FU SU9OIEFVVEhPUklUWTEmMCQGA1UEAxMdR0xPQkUgU1NMIERvbWFpbiBWYWxpZGF0 ZWQgQ0EwHhcNMTAwMjExMDAwMDAwWhcNMTEwMjExMjM1OTU5WjCBjTEhMB8GA1UE CxMYRG9tYWluIENvbnRyb2wgVmFsaWRhdGVkMSgwJgYDVQQLEx9Qcm92aWRlZCBi eSBHbG9iZSBIb3N0aW5nLCBJbmMuMSQwIgYDVQQLExtHbG9iZSBTdGFuZGFyZCBX aWxkY2FyZCBTU0wxGDAWBgNVBAMUDyoubGVlY2hwYWNrLmNvbTCCASIwDQYJKoZI hvcNAQEBBQADggEPADCCAQoCggEBAKX7jECMlYEtcvqVWQVUpXNxO/VaHELghqy/ Ml8dOfOXG29ZMZsKUMqS0jXEwd+Bdpm31lBxOALkj8o79hX0tspLMjgtCnreaker 49y62BcjfguXRFAaiseXTNbMer5lDWiHlf1E7uCoTTiczGqBNfl6qSJlpe4rYBtq XxBAiygaNba6Owghuh19+Uj8EICb2pxbJNFfNzU1D9InFdZSVqKHYBem4Cdrtxua W4+YONsfLnnfkRQ6LOLeYExHziTQhSavSv9XaCl9Zqzm5/eWbQqLGRpSJoEPY/0T GqnmeMIq5M35SWZgOVV10j3pOCS8o0zpp7hMJd2R/HwVaPCLjukCAwEAAaOCAcQw ggHAMB8GA1UdIwQYMBaAFB9UlnKtPUDnlln3STFTCWb5DWtyMB0GA1UdDgQWBBT0 8rPIMr7JDa2Xs5he5VXAvMWArjAOBgNVHQ8BAf8EBAMCBaAwDAYDVR0TAQH/BAIw ADAdBgNVHSUEFjAUBggrBgEFBQcDAQYIKwYBBQUHAwIwVQYDVR0gBE4wTDBKBgsr BgEEAbIxAQICGzA7MDkGCCsGAQUFBwIBFi1odHRwOi8vd3d3Lmdsb2Jlc3NsLmNv bS9kb2NzL0dsb2JlU1NMX0NQUy5wZGYwRgYDVR0fBD8wPTA7oDmgN4Y1aHR0cDov L2NybC5nbG9iZXNzbC5jb20vR0xPQkVTU0xEb21haW5WYWxpZGF0ZWRDQS5jcmww dwYIKwYBBQUHAQEEazBpMEEGCCsGAQUFBzAChjVodHRwOi8vY3J0Lmdsb2Jlc3Ns LmNvbS9HTE9CRVNTTERvbWFpblZhbGlkYXRlZENBLmNydDAkBggrBgEFBQcwAYYY aHR0cDovL29jc3AuZ2xvYmVzc2wuY29tMCkGA1UdEQQiMCCCDyoubGVlY2hwYWNr LmNvbYINbGVlY2hwYWNrLmNvbTANBgkqhkiG9w0BAQUFAAOCAQEAB2Y7vQsq065K s+/n6nJ8ZjOKbRSPEiSuFO+P7ovlfq9OLaWRHUtJX0sLntnWY1T9hVPvS5xz/Ffl w9B8g/EVvvfMyOw/5vIyvHq722fAAC1lWU1rV3ww0ng5bgvD20AgOlIaYBvRq8EI 5Dxo2og2T1UjDN44GOSWsw5jetvVQ+SPeNPQLWZJS9pNCzFQ/3QDWNPOvHqEeRcz WkOTCqbOSZYvoSPvZ3APh+1W6nqiyoku/FCv9otSCtXPKtyVa23hBQ+iuxqIM4/R gncnUKASi6KQrWMQiAI5UDCtq1c09uzjw+JaEzAznxEgqftTOmXAJSQGqZGd6HpD ZqTjb+WBJQ== -----END CERTIFICATE----- subject=/OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com issuer=/C=RO/O=GLOBE HOSTING CERTIFICATION AUTHORITY/CN=GLOBE SSL Domain Validated CA --- No client certificate CA names sent --- SSL handshake has read 3313 bytes and written 343 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 2048 bit Secure Renegotiation IS supported Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: 5F9C8DC277A372E28A4684BAE5B311533AD30E251369D144A13DECA3078E067F Session-ID-ctx: Master-Key: 9B531A75347E6E7D19D95365C1208F2ED37E4004AA8F71FC614A18937BEE2ED9F82D58925E0B3931492AD3D2AA6EFD3B Key-Arg : None Start Time: 1288618211 Timeout : 300 (sec) Verify return code: 21 (unable to verify the first certificate) ---

  Read the article

< Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >