Search Results

Search found 33162 results on 1327 pages for 'static ip address'.

Page 402/1327 | < Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >

  • FTP error when doing file transfer

    - by Ernie
    I'm running vsftpd version 3.0.2 over FTPeS, and I'm having a bit of trouble with file transfers. It seems to work fine when I'm on the LAN, but not from an external IP address. I have the control port and data ports open on my server's software firewall and my router's firewall. When I'm using the service from an external IP address, it seems like sometimes a file transfer will complete, but it times out and I always get the client error: "426 Failure writing network stream". I've tried several clients. I'm thinking there is some sort of data sabotage either at the router or some server policy; maybe because I'm using passive ftp? Suggestions?

    Read the article

  • Cannot access internet or remote network after connecting to Windows VPN

    - by Kiewic
    I set up a VPN by creating an incoming VPN connection (VPN server) in my Windows 8 machine at home (not a Windows Server). I forwarded the PPTP port in my router (port 1723) to this machine and enabled PPTP passthrough. In a second Windows 8 machine out of home, I created an outgoing VPN connection (VPN client). And I am able to connect to my home VPN, but I don't have access to any home resource or even internet. This is the output of the client ipconfig: And this are the settings of my VPN server: UPDATE: My VPN server has assigned the 192.168.1.144 IP adress at my home network. So, I tried setting the "IP address assignment" range from 192.168.1.150 to 192.168.1.200. And when a VPN client gets connected, it gets an address in that range, but it doesn't make any difference.

    Read the article

  • Routing Essentials

    - by zharvey
    I'm a programmer trying to fill a big hole in my understanding of networking basics. I've been reading a good book (Networking Bible by Sosinki) but I have been finding that there is a lot of "assumed" information contained, where terms/concepts are thrown at the reader without a proper introduction to them. I understand that a "route" is a path through a network. But I am struggling with visualizing some routing-based concepts. Namely: How do routes actually manifest themselves in the hardware? Are they just a list of IP addresses that get computed at the network layer, and then executed by the transport? What kind of data exists in a so-caleld routing table? Is a routing-table just the mechanism for holding these lists of IP address (read above)? What are the performance pros/cons for having a static route, as opposed to a dynamic route?

    Read the article

  • Access node.js local server though mobile via same shared wifi

    - by laggingreflex
    EDIT: I was stuck in this situation before but then it was Apache-related But this time I'm using NodeJS, so the old answer doesn't help. I'm running apache a NodeJS webserver (on port 80) on Windows 7. I want to access the webserver through my mobile which shares the wifi router with my pc locally. http://localhost works from PC. But I can't access http://192.168.1.4 from either my phone or even my computer. ipconfig /all on my computer lists my ip address as 192.168.1.4 Wireless LAN adapter Wireless Network Connection: IPv4 Address. . . . . . . . . . . : 192.168.1.4(Preferred) I can ping my phone's (internal) ip address [192.168.1.5] from PC and vice-versa, I can ping my PC [192.168.1.4] from my phone. So why can't I access http://192.168.1.4 from my phone? (or PC) Firewall is off.

    Read the article

  • Some questions regarding Hostname

    - by user481913
    I just bought a new VPS hosting plan and i have a few questions. Hope someone here can clear the doubts for me. 1) Is it necessary to have a real domain for a vps hostname? I suppose i can just use a non-real domain like anydomain.com and something like 'server' for the computer name. Therefore i'll end up with something like server.anydomain.com as the vps's hostname. I want to do this for the sake of putting in a hostname to configure the vps to get it going . So, since this non-real domain name does not need to be publicly accessible i don't need to register or own it and instead access the server by the ip address. Is that correct? But i suppose that this also depends upon if my web host allows that? 2)I would also like to run some real sites with real domain names on this vps, so can i just configure the zone file on the primary nameserver and make entries for these domains and point an A record at the Vps's IP to make them publicly accessible over the internet? For example for my 1st domain i could make an entry like this: $TTL 86400 mydomain1.com. IN SOA ns1.mywebhost.com. \ admin.mydomain1.com. ( 2004011522 ; Serial no., based on date 21600 ; Refresh after 6 hours 3600 ; Retry after 1 hour 604800 ; Expire after 7 days 3600 ; Minimum TTL of 1 hour ) server IN A 200._._._ ns1.mywebhost.com. IN A 216._._._ ns2.mywebhost.com. IN A 205._._._ @ IN NS ns1.mywebhost.com. @ IN NS ns2.mywebhost.com. @ IN MX 10 server www IN CNAME server server IN CNAME @ (so this particular line tells the nameserver to point the url mydomain1.com to server.anydomain.com at the particular ip addresss in the A record.... is that right?) Similarly for my 2nd domain i could have a similar entry : $TTL 86400 mydomain2.com. IN SOA ns1.mywebhost.com. \ admin.mydomain2.com. (..... ............................so on........ ......................................... ......................................... ......................................... ......................................... ......................................... Is that correct? 3) Suppose for my vps hostname, i ignorantly chose a domain that someone else alreadys owns , however i think that it won't affect the public accessibility of the real domain or website since only the real owner of the domain has the rights to provide for the nameservers addresses in the TLD registeries through his Domian Registerar? Is that correct? 4)Can i change my vps's hostname later? Would this create any complications?

    Read the article

  • rsyslog appears to act on old configuration

    - by Jeff Lee
    I'm using a template to dynamically generate rsyslog filenames. I've made some changes from my original format, but rsyslog still appears to be using both the new template and the old after restarting. My filename template went from this: $template RemoteDailyLog,"/var/log/remote/%hostname%/%$year%/%$month%/%$day%.log" To this: $template RemoteDailyLog,"/var/log/remote/%hostname%/%fromhost-ip%/%$year%/%$month%/%$day%.log" I stopped rsyslogd using service rsyslog stop, deleted all of my log files using rm -rf /var/log/remote/*, and then restarted rsyslogd with service rsyslog start. The problem is rsyslog seems to be building folder structures of the type "/var/log/remote/%hostname%/%$year%/%$month%/%$day%.log" (i.e., without the remote IP), which no longer appears anywhere in my configuration. Is it possible that old log or config data have been cached somewhere and are being preserved through the server restart? This is creeping me out a little.

    Read the article

  • Vlaning on WNR3500L

    - by ageis23
    When I try connecting to my wireless network it attempts to connect then gives up. There's something strange going on with the mac's. The eternet switch and all the vlan interfaces have a mac 00:FF:FF:FF:FF:FF. config 'switch' 'eth0' option 'vlan0' '2 3 4 8*' option 'vlan1' '0 8' option 'vlan2' '1 8' config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'type' 'bridge' option 'ifname' 'eth0.1' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ipaddr' '192.168.2.1' option 'ip6addr' '' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' option 'ipaddr' '192.168.1.8' option 'ip6addr' '' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '192.168.1.253' config 'interface' 'dmz' option 'ifname' 'eth0.2' option 'proto' 'static' option 'ipaddr' '192.168.0.1' option 'netmask' '255.255.255.0' Any help on this will be greatly appreciated! When I try setting the mac using macaddr it does nothing. It works perfectly fine when I turn the authentication off. I've also discovered that when wpa2 is switched on I don't receive a association reply from ap. thats my hostapd.conf interface=eth1 driver=broadcom bridge=br-lan ssid=O2BB3 wpa=2 wpa_passphrase=prettywoman wpa_key_mgmt=WPA-PSK rsn_pairwise=CCMP Btw that password is only temporary while am testing.

    Read the article

  • make sure i've configured dns correctly

    - by user22817
    Hi, On my server with Windows Server 2008, i've added a new zone with my new domain: biografica.ro. I've added a name server for it: ns.biografica.ro and the ip of the server. Also i added two A hosts for ns.biografica.ro and www.biografica.ro. I've also defined first that name server on the site where i bought the domain and pointed it to my ip. Now, i understood that i have to wait 24-48 hours for this new domain to be available online. Question: - is this a way to check on the server that i've succesfully configured it? For instance: nslookup biografica.ro or nslookup www.biografica.ro or ping www.biografica.ro do not work locally, on the server... Can you give me an advice? Thanks.

    Read the article

  • Vmware Workstation Development Server on Laptop

    - by Koobz
    I'm running an Ubuntu guest OS on my Windows 7 laptop. Currently, I have it set up for bridged networking. The guest is os is configured for a static ip of 192.168.1.115, which depending on the network I'm connected to, may not be available. When I want to view my development work I hit that up in my web browser. I'm really looking for the following scenario: 1) My guest OS ip address stays constant. 2) I can access my guest os even if I don't have an internet connection, or a lan/router. 3) I can share files with my guest/host. How does one accomplish this using VMware Workstation?

    Read the article

  • Trouble configuring sendmail to relay mail

    - by Warren Schubert
    I am trying to configure sendmail and ufw on an ubuntu server (ServerA) so that another server (ServerB) can send mail through it. In my /etc/mail/access file I have the following line (a.b.c.d is the IP of ServerB): Connect:a.b.c.d RELAY My ufw status shows the following rule I added: 25/tcp ALLOW a.b.c.d When I telnet from ServerA I get through: telnet localhost 25 When I telnet from ServerB I don't (w.x.y.z is the IP of ServerA): telnet w.x.y.z 25 telnet: Unable to connect to remote host: Connection refused I did restart the sendmail daemon after editing the access file. What could I be missing? Something in sendmail.mc? Edit: netstat -an|grep -w 25 tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN

    Read the article

  • Configuring Nagios BGP plugin on Ubuntu

    - by user141610
    I am trying to configure nagios check_bgp_neighbors plug-in on Ubuntu and followed README file of check_bgp_neighbors plug-in. I have made following changes: define command{ command_name check_bgp_all command_line $USER1$/check_bgp_neighbors -H $HOSTADDRESS$ -C $USER3$ -n $ARG1$ -n $ARG2$ } to define command{ command_name check_bgp_all command_line /usr/local/nagios/libexec/check_bgp_neighbors.sh -H xx.xx.xx.49 -C xx.xx.xx.50 And define service{ use server-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!10.0.0.1!172.16.0.2 } to define service{ use generic-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!xx.xx.xx.50 } xx.xx.xx.49 is the IP of the host router and xx.xx.xx.50 is the IP of eBGP neighbour. After that it shows critical status. I know my command is not correct but cannot detect the problem. I learned that in this plug-in user-name and password of the host router are required but don't know how and where to provide it. Nagios log does not show any error message. Status information: Failed: status:0 prefixes:0 sent:0 received:0

    Read the article

  • Trouble opening my router to my web server

    - by Justin Heather Barrios
    Here's the story. I have a webs server created and connected to my router. The website works great when I'm connected to the router, but when I'm off the network I can't access the website. I got the IP for my router by googling "what is my ip." I have opened ports 80 to 10080 to link to the server in the router. One odd thing that I don't understand. When I am in network if I access XXX.XXX.XX.XX:80 I can access the web page no problem. If I access XXX.XXX.XX.XX:81 (or any other port) I get the error "Cannot access server." Any idea what the problem could be? Could it be my ISP?

    Read the article

  • why this routing configuration does not work?

    - by avs099
    I have 2 VMs in HyperV role: first is RRAS - it has 2 interfaces (both manually configured, no DHCP): 192.168.1.110 - "external" one, connected to the router 192.168.10.2 - that's internal interface which other VMs will be using as well also I added VPN connection to our main server - and it gets 192.168.2.136 IP address in 192.168.2.XXX network. And IP route is create on the server as well for this interface. second VM is called KITCHENER. It only has 1 interface 192.168.10.99 / 255.255.255.0, with default gateway set to RRAS server - 192.168.10.2 QUESTION: how can I ping "main server" - 192.168.2.1 - from the KITCHENER server when RRAS server is connected to VPN? please see screenshots with ipconfig /all, route print and ping 192.168.2.1 commands. What needs to be done to get this working? all servers are Windows 2008 R2 if that matters.

    Read the article

  • Windows VPN - NO internet access

    - by sharru
    I host a network of servers behind a Fortigate 200a firewall in the DC. I connect to those servers via a VPN connection. The problem is that when i connect to the VPN, I lose my internet connection on the local PC (windows 7). I would like to be connected to the VPN and still surf the web. i guess this means to only forward a range of ip to the VPN connection. I've read other answers on serverfault, talking about "un-check the 'Use default gateway on remote network' option in your Windows 7 PPTP network connection settings". When i do that , i get internet access but no access to the servers in the VPN. Any idea how to get both working? Should i change something on the fortigate 200a config? Do i need two networks cards? Is there a place in windows to define ip range for the vpn connection?

    Read the article

  • Cisco access list logging. Why is there a difference between IPv4 and IPv6?

    - by growse
    I've got a Cisco 877 router. I've got an IPv4 access list and an IPv6 access list set up and configured similar to this: interface Dialer1 ... ip access-group INTERET-IN ipv6 traffic-filter IPV6-IN Each of these access lists has a final rule of deny ip/ipv6 any any log. However, in my syslog I notice that there's a difference in formatting between the two types of entries. IPv4 will say: %SEC-6-IPACCESSLOGP: list INTERNET-IN denied udp 88.89.209.63(137) -> 1.2.3.4(137), 1 packet Whereas the IPv6 list will say %IPV6_ACL-6-ACCESSLOGNP: list IPV6-IN/240 denied 59 2001:0:5EF5:79FD:14F9:B773:3EBA:3EE3 (Dialer1) -> 2001:800:1000:0::1, 8 packets Both have broadly the same information, but the IPv6 log entry is missing the protocol type and port, both of which are very useful if I'm trying to troubleshoot connectivity. Why is this? How do I get IPv6 deny logs to display the protocol and port used, if any?

    Read the article

  • Configuring subdomains for a machine (Win2k8) in a lan

    - by RMS
    I am currently setting up a windows 2008 server to host a website with multiple subdomains, all accessible only within the lan. also, there is no active directory. what I did is : 1 - computer name : 'web' 2 - in IIS, I added a site binding as 'site1.web' to the default web site 3 - added DNS role to the server 4 - added 'web' as principal zone in direct lookup zones (default options) 5 - added CNAME 'site1' From a client machine, in tcpip config I added the ip address of 'web' to the DNS list in addition to the ISP DNS. (client machine ip is from DHCP) Now browsing to 'http://web' or 'http://site1.web' works correctly. My question is, is it possible throught additional steps in the server to have the websites accessible without requiring the DNS config in all the client machines ? thanks in advance

    Read the article

  • impossible to connect.. days trying..

    - by dany
    I have a problem: I am on Debian. I configured my nic with a static ip (192.168.1.56). When I try to connect to a network, initially with ifconfig eth2 I get (correctly): eth2 inet addr:192.168.1.56 .... inet6 addr: fe80:221:ff:fe96:4598/64 but after a few seconds the 102.168.1.56 disappears and after some other seconds disappears the inet6 address too. When I press in the nm-applet it requires me the password but in the meantime it try to connect. At uni, the connection is a DHCP one. It works for the first few seconds but after it doesn't. Any possible solution? Here it is the relevant part of the syslog: (static ip configuration) http://pastebin.com/u3BPAsda

    Read the article

  • Find computer names on a private network (with nmap?)

    - by paracaudex
    On a LAN, I want to find out the names of all the connected computers using a cross-platform program, preferably nmap. I know I can do nmap -sn xxx.xxx.xxx.xxx/24 (where xxx.xxx.xxx.xxx is a local IP address) to find hosts which are up, but how do I find the computers' hostnames? Do they broadcast this in a way that I can find using nmap? UPDATE: It looks like Angry IP Scanner can do this. How does it do this? Can I replicate it with nmap?

    Read the article

  • IPV6 causing issue with DNS

    - by Mike Wells
    I have set up an 'internal' DNS at my work, basically we have ourdomain.com that is for internet, email etc and I have created on one of our linux network servers (debian) a DNS using bind9 with the domain ourdomain.inc. So based on my files below and the symptoms I'm describing; what effect could IPV6 be having on my setup? What can I do to fix this? I assume it is not actually the IPV6 causing the issue, but rather something in my setup. These are the critical (I think) files I have modified: named.conf.local zone "ourdomain.inc" { type master; file "/etc/bind/zones/ourdomain.inc.db"; }; zone "201.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/rev.201.168.192.in-addr.arpa"; }; named.conf.options options { directory "/var/cache/bind"; // If there is a firewall between you and nameservers you want // to talk to, you may need to fix the firewall to allow multiple // ports to talk. See http://www.kb.cert.org/vuls/id/800113 // If your ISP provided one or more IP addresses for stable // nameservers, you probably want to use them as forwarders. // Uncomment the following block, and insert the addresses replacing // the all-0's placeholder. forwarders { 1.2.3.4; //IP of our external DNS provider }; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; ourdomain.inc.db $TTL 86400 ourdomain.inc. IN SOA ns1.ipower.com. admin.ourdomain.inc. ( 2006081401 28800 3600 604800 38400 ) serv1 IN A 192.168.201.223 serv2 IN A 192.168.201.220 serv3 IN A 192.168.201.219 ns1.ipower.com. IN A 1.2.3.4 ns2.ipower.com. IN A 1.2.3.5 @ IN NS ns1.ipower.com. @ IN NS ns2.ipower.com. svn IN CNAME serv1 docs IN CNAME serv2 jira IN CNAME serv3 confluence IN CNAME serv3 fisheye IN CNAME serv3 rev.201.168.192.in-addr.arpa $TTL 86400 201.168.192.in-addr.arpa. IN SOA ns1.ipower.com. admin.ourdomain.inc. ( 2006081401; 28800; 604800; 604800; 86400 ) 223 IN PTR serv1 @ IN NS ns1.ipower.com. @ IN NS ns2.ipower.com. named.conf include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; I then made our internal DNS my preferred DNS with the two external DNSs the next in-line. More the most part this seems to work, I can ping svn.ourdomain.inc and it resolves to the correct IP, I can also ping google.com and it also resolves no problem. So all seem good. However, periodically (couple of times a day at least), I loose the ability to ping the svn.domain.inc (and all others defined under the internal DNS). What seem to fix the issue temporarily is to disable IPV6 on the network adapter of the client machine and then re-enable it. Then it works for a bit but will always fail again. System Info Internal DNS Distributor ID: Debian Description: Debian GNU/Linux 6.0.6 (squeeze) Release: 6.0.6 Codename: squeeze Linux 2.6.32-5-686 i686 BIND 9.7.3 PC OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7601 Service Pack 1 Build 7601 System Type: x64-based PC Network Card(s): 2 NIC(s) Installed. [01]: Realtek PCIe GBE Family Controller Connection Name: WORK LAN DHCP Enabled: No IP address(es) [01]: the.ipv4.address [02]: the:ipv6:address The question... So based on my files above and the symptoms I described; what effect could IPV6 be having on my setup? What can I do to fix this? I assume it is not actually the IPV6 causing the issue, but rather something in my setup.

    Read the article

  • Mount linux partition as Windows network share over internet

    - by CptEO
    I have a Linux server running RHEL 6. I have two Windows servers. All servers are connected directly to the web with an external IP, they are not in a local lan. What I would like to achieve is to setup the Linux server so that it offers a single share (the whole partition) that can be mounted as network drive within Windows. I don't want to use any 3rd party software to access the linux server because I want to use the linux server as a backup for Bare Metal Restore. In order to do so, I need to be able to access the linux partition from within the Windows Recovery Enviroment where I cannot install any 3rd party software. The linux server should only be accessible from given IP addresses (e.g. the 2 windows servers). Does anyone know if the setup I would like to have is possible?

    Read the article

  • How to connect with MySQL server if it won't connect via the socket?

    - by cwd
    I have an account on a shared server. I have jailshell access and also PhpMyAdmin. I want to run mysql commands via SSH but I'm getting an error: $ mysql -u mySqlUser -p mySqlPw Can't connect to local MySQL server through socket '/var/lib/mysql/mysql.sock' I can connect with PHP and phpMyAdmin, so would it be possible to call mysql from the shell and have it connect via an ip and port instead of the socket? The file /var/lib/mysql/mysql.sock does not exist - maybe that is intentional, and the only thing in /etc/my.cnf is [mysqld] skip-innodb More Info I don't have access to change system settings. I did a search in /var for mysql.sock but found nothing. However, phpMyAdmin might be connecting via a socket somehow: Really it would just be great if I could connect via IP. Also tried these two syntaxes: $ mysql -u mySqlUser -p mySqlPw -h localhost $ mysql -u mySqlUser -p mySqlPw -h localhost -P 3306 Both with the same result: ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/lib/mysql/mysql.sock' (2)

    Read the article

  • Hp Procurve Switch : port filtered

    - by user117140
    My HP Procurve switch is blocking port 22 and I dont know how to unblock it.Please let me know From the server, see port 22 is blocked [root@server ~]#nmap -p22,80,443 10.247.172.70 Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2012-04-16 14:12 IST mass_dns: warning: Unable to determine any DNS servers. Reverse DNS is disabled. Try using --system-dns or specify valid servers with --dns_servers Interesting ports on 10.247.172.70: PORT STATE SERVICE 22/tcp filtered ssh ------------------> see 80/tcp filtered http 443/tcp filtered https This is blocked on cisco switch but I dont have any clue how this is done. I know that vlan is configured on switch. vlan 54 ip ospf 10.247.172.65 area 0.0.0.10 vrrp vrid 54 owner virtual-ip-address 10.247.172.65 255.255.255.192 priority 255 enable exit exit Please let me know how to unblock ssh port 22 access on this switch?

    Read the article

  • Windows 7 "Could not reconnect all network drives" on boot

    - by Thermionix
    Windows 7 won't reconnect to my network drives on startup. Once it is done booting opening Windows Explorer and clicking each share will mount them. Windows 7 Enterprise N Service Pack 1 I have attempted formatting the windows machine - first thing done to machine was to map the network drives, upon reboot they were disconnected. It is running on an Crucial M4 64gb SSD. The host of the network shares is a Ubuntu-Server machine connected through a gigabit switch. A modem provides dhcp, although both these machines have static IP's defined. It won't reconnect the drives regardless of whether they're SAMBA shares or NFS shares - therefore I believe it's an issue with the windows machine. Ubuntu 11.10 (GNU/Linux 3.0.0-12-server x86_64) I've tried using ip address instead of netbios name for mapping shares on the windows machine, Also tried setting EnableLinkedConnections=1 gpedit.msc Computer Configuration - Administrative Templates - System-Logon - always wait for the network at computer startup and logon = yes

    Read the article

  • Connect to CentOS LAMP instance from Windows PCs

    - by Gnanesh
    I have a CentOS 6 machine running on our network which has a simple LAMP installation on it. I have some files there which I would want to access through other Windows PC which I am able to do so using the IP address of the CentOS machine. Since the IP address of the CentOS machine also could be dynamic I would want to connect to it using the computer / host name But I am not able to do so using the computer / host name of the CentOS machine. Can someone help me point out what I may be missing and help me out to resolve this?

    Read the article

  • Windows 7 PPTP VPN problem

    - by Marco Martins
    Hi, I'm currently using an win 7 as an network server at my home. I've created some shared folders wich can be accessed easily from any pc on my network (win and mac computers) recently I decided to turn on the win 7 pptp to access remotely to my server from anywhere. the problem is with that on, on my router my server ip change, acording to my ipconfig on the cmd my router gets the ip from a "PPP adapter RAS (dial in)". when that happens I cannot access to the shared files over the lan on my mac, but i can connect to the vpn but again can't access to my files. (i've tried connecting to the vpn from another network and it worked, even the file share) anyone can help me? thanks

    Read the article

< Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >