Search Results

Search found 15348 results on 614 pages for 'invalid ip'.

Page 404/614 | < Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >

• Pfsense: Inbound Load Balancing https with sticky connection

  - by Zeux

  first of all I'm very sorry for my English... This is my scenario: Internet Firewall+LB: pfsense_1(Active) + pfsense_2(Passive) in CARP Pool servers: 3 x nginx(PHP5+HTTP+HTTPS) Pfsense 1 and 2 CARP configured with Virtual IP (pubblic). Nginx servers's ips are all private. I want to load balance inbound HTTP and HTTPS connections between the 3 nginx web servers. An importat thing is that the HTTPS connections must be "sticky connections": in HTTPS connections, after login by username and password, I setup a php session and therefore when a client starts a HTTPS connection it will be always redirected to the same nginx server, until it disconnects itself, it closes the page/browser or after a timeout (30minutes?) without activity. Is this possible whit the last release(2.0.1) of pfsense? thank you very much...

  Read the article

• iptables openvpn forward selectively from eth to tun

  - by Bryan Hunt

  Simple for those who know, indecipherable for those who don't... I'm running openVPN on (hypothetical) 66.66.66.66, I want to FORWARD incoming traffic, arriving on interface eth0 to interface tun0. It would also be nice to filter - based on destination IP address. I'm doing the NAT later on, but like to lock down early wherever possible. So onto the main course... This works: #Enable forwarding from eth0 to tun0 iptables -A FORWARD -i eth0 -o tun+ -j ACCEPT But this doesn't pass any packets whatsoever: #Stricter version iptables -A FORWARD -i eth0 -o tun+ --dst 66.66.66.66 -j ACCEPT Am I being unacceptably foolish?

  Read the article

• my Website loss packet in 70% countries, how can i dertermine why its loss packets?

  - by user2511667

  I checked my website on google page speed tester, it show result 90/100. I checked my website on pingdom it shows good result there. When i check my website in cloudmonitor.ca.com, it shows good result in 30% countries and all other countries it show packet loss (100%) How we can determine why my website has packet loss? And what is its solution? Is this problem from my server or from my website? I created new html blank page and set it too my index page, after I tested, it still shows packet loss, guess this means the problem is not in my website. Here is live result When I visit my website in browser, website is working fine. But when i test my domain or IP 198.178.123.219 in command Prompt it shows "Request time out" Why time out in command prompt?

  Read the article

• CheckPoint VPN-1 SecureClient inability to navigate behind a Linksys WAG300N

  - by AndreaTrasatti

  I have a Linksys WAG300N, I'm accessing my LAN with Wifi and everything works fine on my Windows 7 Enterprise laptop. When I try to connect to my company's VPN the connection succeeds, but I cannot access any internet site either within my work network or public site like Yahoo or Google. In my Linksys control panel I already verified all types of VPNs are enable to passthrough. Normal IPSec and Windows VPN worked in the past without any problems. CheckPoint seems to have a solution, but I do not have the ability to change the IP in my client and of course using another NAT device in between is not a solution for me. Edit: adding link to the Checkpoint solution, https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=sk26189

  Read the article

• Cannot access Tomcat application remotely, but can access Apache applications

  - by David Keaveny

  I am installing Atlassian's Confluence 4.2 on a clean Ubuntu 12.04 server. Confluence runs on Tomcat 6, and uses PostgreSQL 9.1 as its datastore. I've installed and configured phpPgAdmin to manage PostgreSQL, and Zentyal to manage the server generally. Both these applications use Apache. The problem that I am experiencing is that while I can access phpPgAdmin and Zentyal without problem from a remote PC, I can only access Confluence when running locally (either specified by localhost, IP address or host name). Instead I get an HTTP 502 Connection Failed error. By way of experimentation, I also installed Ajenti, which appears to use lighttpd rather than Apache or Tomcat, and it too works fine when connected to locally, but gives me the same HTTP 502 error when connected to remotely. So applications served from Apache work fine, but applications served from other services do not - does that ring a bell with anyone? It's been over 10 years since I last sysadmin'ed a Linux box, so I'm more than a little rusty!

  Read the article

• Locate rogue DHCP server

  - by Farseeker

  I know this is a serious long shot, but here we go. In the past week or so, for users connected to a particular switch in our network (there are four dumb switches all connected, and it only affects SOME, not all, users on the one switch) are getting DHCP addresses from a rogue DHCP server. I have physically checked every cable plugged into the switch in question to make sure that none of them have a router or wifi point attached to it. I know the IP of the DHCP server, but I cannot ping it, and it does not have a web interface. Does anyone have any suggestions on what I can do to locate it or shut it down? Unfortuantely all the switches are unmanaged, and as mentioned, there's no physical device (that I can find) plugged in to anything. It's getting critical, because it's screwing up the PXE boot of a whole bunch of thin clients.

  Read the article

• configuration transfer over scp on commit not working on Juniper EX-2200 switch

  - by liv2hak

  I am making a series of configuration changes on Junos EX- 2200 switch.I have this router connected to another PC via an ethernet cable.The IP address of the switch is 192.168.1.1.I am able to ping from 192.168.1.1 to 192.168.1.0 and vice-versa. After the changes I make I do the following commands set system archival configuration transfer-on-commit set system archival configuration archive-sites "scp://[email protected]:/home/karthik/ws_karthik/sw1_config_1.txt" password godfather commit Where there is a user with user-name "karthik " and password "godfather".The path shown above also exists in the system How ever I don't see the configuration file sw1_config_1.txt created at the path specified. Also I have verified that sshd is running on the PC (192.168.1.10) Am I doing something wrong here? It would be great if anyone could help me out.

  Read the article

• How can I: Convert Physical to VM, the machine it's running on

  - by Daisetsu

  I have virtualized laptops before, when someone gets a new one and doesn't want to quite let go of their old laptop for fear of losing something. This was using VMWare Workstation 7.X. In 8.0 when I go to "Convert a Physical Machine to a Virtual Machine", it asks for an IP address and doesn't give the option to virtualize the machine it's running on. How to I get VMWare to virtualize it's current system? I tried typing in Localhost, and 127.0.0.1 but that didn't do it.

  Read the article

• How to open ports on modem for better torrent performance

  - by Mehper C. Palavuzlar

  I've been using utorrent to download and upload torrents for a long time. Recently someone told me that I need to open port(s) for utorrent from my modem settings for better downloading and uploading performance. Is it true? If yes, how can I do that? My utorrent version: 2.0 and the port used for incoming connections: 61829. My modem: Yaksu S200 ADSL router modem and I can reach its settings via web interface. I looked at the settings but they seem a bit complicated to me. Other info you may need to know: I have dynamic IP. I'm using Win7 x64.

  Read the article

• Dell printer goes offline after second print job.

  - by Ac0ua

  Dell printer goes offline(server connection) after second print job. Although the printer's display says it is ready. If you turn off then on the printer you can send one job and goes back offline(server connection) on the next print job. We have multiple Dell 2330dn printers installed through a print server, only one of the printers is experiencing this problem. Two different users. Two different machines. Two different operating systems (win7 and Vista). The computers have been reset. Dell printers have web interface if this helps (through IP address). Thanks for any help!

  Read the article

• LFD always stops working after ~30 days, until I give /etc/csf/csf.pl -r

  - by gus

  When I give /etc/csf/csf.pl -r , I see lots of lines flushing, then I begin to get the notification emails again, (several emails per day), for example: Time: Wed Sep 12 08:39:47 2012 +0800 IP: 221.13.104.162 (CN/China/-) Failures: 5 (sshd) Interval: 300 seconds Blocked: Permanent Block Log entries: Sep 12 08:39:25 MyHost sshd[9677]: Failed password for root from 221.13.104.162 port 51106 ssh2 Sep 12 08:39:28 MyHost sshd[9712]: Failed password for root from 221.13.104.162 port 51690 ssh2 Sep 12 08:39:32 MyHost sshd[9739]: Failed password for root from 221.13.104.162 port 52128 ssh2 Sep 12 08:39:36 MyHost sshd[9778]: Failed password for root from 221.13.104.162 port 52670 ssh2 Sep 12 08:39:40 MyHost sshd[9821]: Failed password for root from 221.13.104.162 port 53155 ssh2 And then after about 30 days, the emails stop coming, it is as if something has filled up, and requires flushing again. I don't know much about CSF/LFD, but I would have imagined that this would work in a FIFO manner, so it should be able to run indefinitely within finite space. My /etc/csf/version.txt says 4.83 My cat /proc/version says Linux version 2.6.18-028stab066.8 (root@rhel5-64-build) (gcc version 4.1.2 20070626 (Red Hat 4.1.2-14)) #1 SMP Fri Nov 27 20:19:25 MSK 2009

  Read the article

• I just got a linode VPS a week ago and I've been flagged for SSH scanning

  - by meder

  I got a 32-bit Debian VPS from http://linode.com and I really haven't done any sort of advanced configuration for securing it ( port 22; password enabled ). It seems somehow there is ssh scanning going on from my IP, I'm being flagged as this is against the TOS. I've been SSHing only from my home Comcast ISP which I run Linux on. Is this a common thing when getting a new vps? Are there any standard security configuration tips? I'm quite confused as to how my machine has been accused of this ssh scanning.

  Read the article

• How to handle external and internal DNS on windows 2012

  - by ThePopcorn

  I'm trying to setup an Active Directory network on Server 2012 R2, and want AD's DNS to only be used internally (Ex: domain-controller.company.com) as well as some records that need both internal and external accessibility (Ex: mail.company.com) that use internal IP's on the internal network and finally some records that only need external access. The only solutions i have been able to think of, or look up are to either use a sub domain that handles all internal records, and use the plain company.com domain for all external records. These both seem to mean i have to manage two DNS servers separately. Is either of these the best ways or am i messing up somewhere?

  Read the article

• Sonicwall networking

  - by Syed

  My Sonicwall LAN subnet is 192.168.1.0/24 X0: LAN IP 192.168.1.253 I also have intranet router 192.168.1.108 routing to 192.168.2.0/24 network. Internet is through WAN (X1) is all working fine. My LAN PC's can connect to intranet 192.168.2.0/24 via static route from LANsubnet to 192.168.2.0/24 as 192.168.1.108 as gateway. Now I have LAN2 10.2.1.254 (10.2.1.0/24)on X4 port. I can access Internet from LAN2, now I want to allow intranet from LAN2. What static routes do I need to make this work?

  Read the article

• Double default gateway ubuntu server

  - by Elena

  I've just installed an Ubuntu server 9.10 on an EEEBox. This is my /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto wlan0 iface wlan0 inet static address 192.168.48.16 netmask 255.255.248.0 wireless-essid mynet auto eth0 iface eth0 inet static address xx.xx.xx.xx netmask 255.255.255.224 gateway xx.xx.yy.yy When I restart /etc/init.d/networking, I can access the eth0 ip address from the internet and I can ping the machines in my wifi network mynet. Everything works fine and I have one default gateway. But after some time if I check again the route I just find two default gateways: one is correct and is the previous one, but the other is the one of the wifi network. I have a quite low signal of mynet where my server is and sometimes the wifi just disconnect and then reconnect again. Then I think that this can be a problem and the dhcp of the wifi net, when reconnecting it also add a default gateway. Any idea on how to resolve this issue?

  Read the article

• XAMPP - allow internet connection

  - by user1645034

  I usually do my web dev on a production server, now i need to bring some work at home. I have installed XAMPP on my laptop and it seems to work perfectly fine. Most of my project involves CURL enabled, I need to make my xampp application to access the internet. Perhaps give it some IP address and Gateway. I've seen documentation how to enable CURL on xampp, yet I'm struggling to find how to make XAMPP to have internet access. I'm not asking how to access my XAMPP remotely, I'm simply asking how to give internet connection to xampp application for my CURL and other social network API to work.

  Read the article

• Need help diagnosting a random BSOD

  - by diimdeep

  I have random BSOD even in idle .. Already tried: memtest - ok scandisk- ok netsh int ip reset Winsock fix. tcpip.sys+2c13e 21.06.2011 15:21:00 DRIVER_IRQL_NOT_LESS_OR_EQUAL tcpip.sys+2de08 22.06.2011 15:09:28 DRIVER_IRQL_NOT_LESS_OR_EQUAL tcpip.sys+2de08 22.06.2011 16:09:31 DRIVER_IRQL_NOT_LESS_OR_EQUAL tcpip.sys+2c13e 23.06.2011 9:48:16 DRIVER_IRQL_NOT_LESS_OR_EQUAL Fastfat.SYS+4dc 21.06.2011 11:55:10 SYSTEM_THREAD_EXCEPTION_NOT_HANDLED ipnat.sys ipnat.sys+6751 ntoskrnl.exe ntoskrnl.exe+699e0 tcpip.sys tcpip.sys+2c13e 0 HTTP.sys HTTP.sys+15d00 ipnat.sys ipnat.sys+6751 tcpip.sys tcpip.sys+2de08 ipnat.sys ipnat.sys+6751 ntoskrnl.exe ntoskrnl.exe+79d94 tcpip.sys tcpip.sys+2c13e Fastfat.SYS Fastfat.SYS+4dc ntkrnlpa.exe ntkrnlpa.exe+8d820 Here is .dmp files and report generated by BlueScreenView https://skydrive.live.com/redir.aspx?cid=7e5eafae5336f402&resid=7E5EAFAE5336F402!116 Please help !! I know this questions but answers in it not help Only browser causes BSOD -- all other TCP operations okay

  Read the article

• 2 (or 3 or 4...) websites in IIS, pointing to same ASP.NET application IIS

  - by billfredtom

  I wish to maintain a single a single code base (ASP.NET app) setup at c:\inetpub\wwwroot\myApp, and point several IIS websites at this single code base. Will this be an issue? Will IIS see this as a conflict in resource allocation? Reasons why I want to do it: Each IIS website can then have it's own IP, SSL cert, etc. Each IIS website can have it's own ISAPI filters installed for friendly URLs, etc. Easier to maintain the code base by having single point of deployment

  Read the article

• What consequences to take from what i read in logfiles?

  - by Helene Bilbo

  Since some weeks i manage my first Webserver, a Seaside application behind an Apache proxy on Linode, and i installed logwatch to send me daily logs. Where can i get information on when i have to act as a consequence of what i read in these logwatch reports? For example i read that all kinds of people try to login on funny nonexisting accounts or all kinds of webcrawlers test for nonexisting cms login pages, some ip adresses get banned and unbanned by fail2ban... I assume that's normal? Is it? But how do i know that i probably have to do something? What do i look for in the logs?

  Read the article

• Implementing a Linux-HA based clustering setup on Windows

  - by Alex

  I have a (tried and tested) setup involving: 2x Load balancing nodes on a floating IP via Heartbeat, load balancing 2 tomcat servers. 2x Tomcat servers 2x Galera Cluster MySQL servers synchronously replicating (+1 arbitrator node) All are evenly spread across 2 physical nodes. Now, I have to somehow get the same functionality on Windows Server (2008? I think) nodes .... running under Xen virtualization. There is no possibility to use Linux for any of the nodes. I count two main problems: No Linux-HA hearbeat daemon for the load balancing No Galera synchronous replication for MySQL I freely admit to having nearly no Windows knowledge when it comes to clustering. Is there a way to closely mimic the setup I have described or is it a total write-off?

  Read the article

• DNS server not functioning correctly

  - by Shamit Shrestha

  I have setup a DNS server which isnt working properly. My domain is accswift.com which has glued to two name servers ns1.accswift.com and ns2.accswift.com for the same IP address - 203.78.164.18. On domain end everything should be fine. Please check -http://www.intodns.com/accswift.com I am sure its the problem with the linux server. Can anyone help me find where the problem is for me? Below is the settings that I have in the server. ====================== DIG [root@accswift ~]# dig accswift.com ; << DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6_4.6 << accswift.com ;; global options: +cmd ;; Got answer: ;; -HEADER<<- opcode: QUERY, status: NOERROR, id: 11275 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 2, ADDITIONAL: 2 ;; QUESTION SECTION: ;accswift.com. IN A ;; ANSWER SECTION: accswift.com. 38400 IN A 203.78.164.18 ;; AUTHORITY SECTION: accswift.com. 38400 IN NS ns1.accswift.com. accswift.com. 38400 IN NS ns2.accswift.com. ;; ADDITIONAL SECTION: ns1.accswift.com. 38400 IN A 203.78.164.18 ns2.accswift.com. 38400 IN A 203.78.164.18 ;; Query time: 1 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Wed Nov 6 20:12:16 2013 ;; MSG SIZE rcvd: 114 ============== IP Tables settings vi /etc/sysconfig/iptables *filter :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A FORWARD -o eth0 -j LOG --log-level 7 --log-prefix BANDWIDTH_OUT: -A FORWARD -i eth0 -j LOG --log-level 7 --log-prefix BANDWIDTH_IN: -A OUTPUT -o eth0 -j LOG --log-level 7 --log-prefix BANDWIDTH_OUT: -A INPUT -i eth0 -j LOG --log-level 7 --log-prefix BANDWIDTH_IN: -A INPUT -p udp -m udp --sport 53 -j ACCEPT -A OUTPUT -p udp -m udp --dport 53 -j ACCEPT COMMIT Completed on Fri Sep 20 04:20:33 2013 Generated by webmin *mangle :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT Completed Generated by webmin *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT ====DNS settings vi /var/named/accswift.com.host $ttl 38400 @ IN SOA ns1.accswift.com. root.ns1.accswift.com. ( 1382936091 10800 3600 604800 38400 ) @ IN NS ns1.accswift.com. @ IN NS ns2.accswift.com. accswift.com. IN A 203.78.164.18 accswift.com. IN NS ns1.accswift.com. www.accswift.com. IN A 203.78.164.18 ftp.accswift.com. IN A 203.78.164.18 m.accswift.com. IN A 203.78.164.18 ns1 IN A 203.78.164.18 ns2 IN A 203.78.164.18 localhost.accswift.com. IN A 127.0.0.1 webmail.accswift.com. IN A 203.78.164.18 admin.accswift.com. IN A 203.78.164.18 mail.accswift.com. IN A 203.78.164.18 accswift.com. IN MX 5 mail.accswift.com. ====Named.conf vi /etc/named.conf options { listen-on port 53 { 127.0.0.1; }; listen-on-v6 port 53 { ::1; }; directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; allow-query { any; }; recursion yes; allow-recursion { localhost; 192.168.2.0/24; }; dnssec-enable yes; dnssec-validation yes; dnssec-lookaside auto; /* Path to ISC DLV key */ bindkeys-file "/etc/named.iscdlv.key"; managed-keys-directory "/var/named/dynamic"; forward first; forwarders {192.168.1.1;}; }; logging { channel default_debug { file "data/named.run"; severity dynamic; }; }; zone "." IN { type hint; file "named.ca"; }; include "/etc/named.rfc1912.zones"; include "/etc/named.root.key"; zone "accswift.com" { type master; file "/var/named/accswift.com.hosts"; allow-transfer { 127.0.0.1; localnets; 208.73.211.69; }; }; zone "ns1.accswift.com" { type master; file "/var/named/ns1.accswift.com.hosts"; }; ==================================== Can anybody find any flaw in this? I am still unable to reach accswift.com from any other ISP. But it is browsable from the same network though. Thanks in advance.

  Read the article

• Can't access Linux machine from the network, network from the machine is fine

  - by Matt

  I'm having issues with a machine that stopped replicating with mysql. It's managed by a guy on another continent but recently I've had to get involved. The server is running Ubuntu server 9.10 I can't log in with SSH, there is no response. On the server itself I can ssh to localhost fine. I thought maybe it's the firewall rules. I'm no expert on IP Tables, but I believe that's not the issue as I removed all the rules. But it still won't let me in. Any ideas? it's acting from other machines as though the service isn't listening, but I know that it is. It's like this for all services.

  Read the article

• Setting up a wireless access point with Ubuntu server

  - by Solignis

  I am trying to setup a wifi access point with my Ubuntu server, everything "seems" to be good since I got a better wifi radio (long story). But now I am a little confused, when my Android phone tries to associate with the AP it is able to with no problem but then it cannot get an IP address from my DHCP server. I have tried messing with firewall rules, nothing... I tried making a bridge interface as per what I am told I had to do. ( Not sure if i did it right though). What I am trying to do if make the wireless interface an extention of my eth0 network. Am I on the right track or am I going about the wrong way?

  Read the article

• How to restrict Apache Location directive to cetain sub-domain?

  - by ohho

  On our server www.example.com, we use the <Location> directive to proxy traffic to a back-end server: <Location /app1> ProxyPass http://192.168.1.20 </Location> Then we added a sub-domain uat.example.com which points to the same IP address of www.example.com. We want to use it as a proxy for client to test an app being developed. Hopefully, the client can access via: http:/uat.example.com/app2_uat Now if we add a Location: <Location /app2_uat> ProxyPass http://192.168.1.30 </Location> The client can access both: http:/www.example.com/app2_uat http:/uat.example.com/app2_uat How can I restrict Location such that only: http:/uat.example.com/app2_uat is accessible? (i.e. http:/www.example.com/app2_uat should not be accessible.)

  Read the article

• Why did my Cisco router hang?

  - by Mike Pennington

  We have a Cisco 1841 in our storage IDF that was originally running a 12.4(1) IP-BASE image; I wanted to upgrade to an advancedservicesk9-mz image, but the flash did not have enough space, so I deleted the running image. Later I tried inserting a larger CF from a Catalyst4500, which crashed the 1841 router (now without a bootable image). Using another 1800 series router, I loaded the 12.4(25g) advancedservicesk9 image and verified the image checksums. I set the confreg to 0x2102 from rommon and booted the new image; however the 1841 now hangs indefinitely after printing the IOS export control banner. I have tried four other images, all with the same results. What is wrong with this router? UPDATE 1: I tried loading images from a FAT16-formatted USB, but this didn't work either. I also tried tftpdnld from rommon, but got a get_mac_address(): Search T_IDPROM_MACADDR (0xc3) failed Illegal MAC address. error and the file would not load.

  Read the article

< Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >