Search Results

Search found 19200 results on 768 pages for 'xp mode'.

Page 404/768 | < Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >

• practical security ramifications of increasing WCF clock skew to more than an hour

  - by Andrew Patterson

  I have written a WCF service that returns 'semi-private' data concerning peoples name, addresses and phone numbers. By semi-private, I mean that there is a username and password to access the data, and the data is meant to be secured in transit. However, IMHO noone is going to expend any energy trying to obtain the data, as it is mostly available in the public phone book anyway etc. At some level, the security is a bit of security 'theatre' to tick some boxes imposed on us by government entities. The client end of the service is an application which is given out to registered 'users' to run within their own IT setups. We have no control over the IT of the users - and in fact they often tell us to 'go jump' if we put too many requirements on their systems. One problem we have been encountering is numerous users that have system clocks that are not accurate. This can either be caused by a genuine slow/fast clocks, or more than likely a timezone or daylight savings zone error (putting their machine an hour off the 'real' time). A feature of the WCF bindings we are using is that they rely on the notion of time to detect replay attacks etc. <wsHttpBinding> <binding name="normalWsBinding" maxBufferPoolSize="524288" maxReceivedMessageSize="655360"> <reliableSession enabled="false" /> <security mode="Message"> <message clientCredentialType="UserName" negotiateServiceCredential="false" algorithmSuite="Default" establishSecurityContext="false" /> </security> </binding> </wsHttpBinding> The inaccurate client clocks cause security exceptions to be thrown and unhappy users. Other than suggesting users correct their clocks, we know that we can increase the clock skew of the security bindings. http://www.danrigsby.com/blog/index.php/2008/08/26/changing-the-default-clock-skew-in-wcf/ My question is, what are the real practical security ramifications of increasing the skew to say 2 hours? If an attacker can perform some sort of replay attack, why would a clock skew window of 5 minutes be necessarily safer than 2 hours? I presume performing any attack with security mode of 'message' requires more than just capturing some data at a proxy and sending the data back in again to 'replay' the call? In a situation like mine where data is only 'read' by the users, are there indeed any security ramifications at all to allowing 'replay' attacks?

  Read the article

• HTML APIs for touch devices?

  - by askvictor

  What HTML APIs are available for touch screen devices (e.g. tablet PCs)? I notice that GMail's iPad interface (and other mobile interfaces) doesn't scroll down in a normal web browser (pretending to be an iPad via a user-agent hack). How can one access this API on a PC? I have a school full of tablet PCs that aren't wonderful in tablet mode due to lack of application support, but there looks to be an increasing number of web-based apps that will fill this gap.

  Read the article

• How to do auto complete in city textbox

  - by Manoj Wadhwani

  I have state and city dropdown list in asp.net 3.5 applicattion . but i want city as a textbox when i type keyword then autocomplete mode should be occour . I want to implement it through juery could u please send code for this. Thanks Manoj

  Read the article

• changing vim's vertsplit character to ¦

  - by ldigas

  This is, I assume, codepage related, but doesn't hurt asking. How would one, on windows xp's cmd, gvim 7.2 change vertsplit character, so that instead of default | it is ¦ (so that it makes a full, and not an splitted line) ? That character is usually changed with set fillchars=vert:\| and I can copy paste the ascii graphics line there, but it comes out as garbage. I suppose I would have to change vim's internal codepage for it to show correctly ? Anyone knows how to do this ?

  Read the article

• Code review tool for CM synergy

  - by Ravisha

  I am looking for a code review tool which can be configured with CM synergy .We are having java project with Eclipse 3.4 as IDE.And need a simple code review tool on windows XP. http://www.windriver.com/cgi-bin/partnerships/directory/viewProd.cgi?id=1451

  Read the article

• ImportError: No module named optparse in jython

  - by jeet

  getting Traceback (most recent call last): File "C:\projects\myproject\convert.py", line 139, in import optparse ImportError: No module named optparse. when executing it using jython. Same module works fine when i execute it through python. I am usinng window7 operating system. The same modle works fine on windows XP machine with both python and Jython.

  Read the article

• How to uninstall Iphone sdk?

  - by monish

  Hi guys, Here Im getting a problem when Im uninstalling the Iphone sdk through terminal with the command as: sudo /Developer/Library/uninstall-devtools mode=all;; When I used this its displaying the command is not found. Is there any other method to unistall Iphone sdk? Anyone's help will be much appreciated. Thank you, Monish.

  Read the article

• How can I get This SQL query to search without MATCH. It returns everything too broad.

  - by Kirk

  $sql = mysql_query("SELECT id, email, url, section, date_modified FROM emails WHERE MATCH(id, email, url, section, date_modified ) AGAINST('$query' IN BOOLEAN MODE) ORDER BY date_modified DESC");

  Read the article

• New View when device is rotated

  - by Sebastian

  Hi, I want to call "presentmodalviewcontroller" when the iPhone / iPod Touch is rotated to landscape mode with a flip animation. When it gets rotated back to portrait, I want to present the first view again, again with the flip animation. Weren't able to find something working on the web :( I'm sure you can help me :) Thanks a lot ! Sebastian

  Read the article

• Certificates Validations Issues

  - by user298331

  Hi All, i am facing some issues related certificates.i need some help to resolve these issues. Requirements : security mode="TransportWithMessageCredential" binding binding name="basicHttpEndpointBinding" certificateValidationMode ="ChainTrust" revocationMode="Online" Certificates : Service Cerificates : Transportlevel : XXXX.cer my cerificate name is my system DNS name and it is having root node i.e RootTrnCA.cer this is used to enable https.but am not validationg transport level certificates. Message Level : services.ca.iim (VXXXX.Cer--Act.Mac.Ca--services.ca.iim ) Client Cerificates : Transportlevel : ZZZZ.cer my cerificate name is my system DNS name and it is having root node i.e RootTrnCA.cer ignoring transport certificate errors through coading..... Message Level : client.ca.iim (VXXXX.Cer--Act.Mac.Ca--client.ca.iim ) Issues : 1) Response message is not contain Service certificate Signature in Soap header.so i am not able to validate Server certificate details in Client code. 2)if i use the transport with message credential and Chaintrust.i am getting error : The revocation function was unable to check revocation because the revocation server was offline.) so please very the below service and cleint config and correct me if i am wrong. Service config : Client config : i am attaching certificate through coading : objProxy.ChannelFactory.Credentials.ClientCertificate.SetCertificate(System.Security.Cryptography.X509Certificates. StoreLocation.LocalMachine, System.Security.Cryptography.X509Certificates. StoreName.My, X509FindType.FindBySubjectName, "client.ca.iim"); <binding name="XXXXXServiceHost.Http" closeTimeout="00:01:00" openTimeout="00:01:00" receiveTimeout="00:10:00" sendTimeout="00:01:00" allowCookies="false" bypassProxyOnLocal="false" hostNameComparisonMode="StrongWildcard" maxBufferSize="65536" maxBufferPoolSize="524288" maxReceivedMessageSize="65536" messageEncoding="Text" textEncoding="utf-8" transferMode="Buffered" useDefaultWebProxy="true"> <readerQuotas maxDepth="32" maxStringContentLength="8192" maxArrayLength="16384" maxBytesPerRead="4096" maxNameTableCharCount="16384" /> <security mode="TransportWithMessageCredential"> <transport clientCredentialType="None" proxyCredentialType="None" realm="" /> <message clientCredentialType="Certificate" algorithmSuite="Default" /> </security> </binding> </basicHttpBinding> </bindings> <client> <endpoint address="https://XXXXXX/XXXServiceHost/MemberSvc.svc/soap11" binding="basicHttpBinding" bindingConfiguration="XXXServiceHost.Http" contract="ServiceReference1.IMemberIBA" name="XXXServiceHost.Http" /> </client> </system.serviceModel>Please Verify both and Help me how to resolve above two issues . Thanks Babu

  Read the article

• How to force asdoc run in English

  - by ty

  My operation system is Window XP in Chinese. I'm running flex sdk asdoc in command line. Asdoc picks up the system default language. How can I force it to be run in English language environment?

  Read the article

• How to perform CAM authentication with Cognos TM1 API

  - by tardate

  The Cognos TM1 API provides two server connect/authenticate methods: TM1SystemServerConnect (when IntegratedSecurityMode = 1 or 2) TM1SystemServerConnectIntegratedLogin (when IntegratedSecurityMode = 2 or 3) There is however a 4th security mode for use with CAM/Cognos Access Manager (IntegratedSecurityMode = 4). As of 9.5, it appears there is still no way to authenticate via the API if you have CAM enabled on the TM1 server. Does anyone know different, or have a workaround?

  Read the article

• AS3: How to get fullscreen and keyboard input?

  - by Tinelise

  Since flash doesn't allow keyboard input while in fullscreen mode I'm wondering if there is a workaround to that? I have a flash that is going to run fullscreen in a browser and needs different kinds of keyboard input. I have read something about AIR, but I don't fully understand it and would like another way if thats even possible. Anybody knows?

  Read the article

• Using Apple’s Bonjour service from .NET?

  - by Martín Marconcini

  I have an iPhone app that publishes through Bonjour. The Mac counterpart works, they sync and exchange data. Now I have to port that little Mac app to Windows. I’ve decided to go with .NET (because that’s what I know). The app is not complex, but I’m in the early stages. I need to browse/discover Bonjour services. For this task, I’ve downloaded Mono.Zeroconf and Apple’s latest SDK (which includes a couple of C# Samples). I’m not really pasting code because I’m really copy/pasting the samples. In fact, Mono.Zeroconf has a MZClient.exe that can be used to test “all the API”. My 1st test was -on the same box- open two cmd.exe and launch a MZclient registering a service and on the other, launch it and “discover it”. It doesn’t work. Here’s the server: C:\MZ>MZClient -v -p "_http._tcp 80 mysimpleweb” *** Registering name = 'mysimpleweb', type = '_http._tcp', domain = 'local.' *** Registered name = ‘mysimpleweb’ On the other terminal: c:\MZ>MZClient -v -t "_http._tcp" Creating a ServiceBrowser with the following settings: Interface = 0 (All) Address Protocol = Any Domain = local Registration Type = _http._tcp Resolve Shares = False Hit ^C when you're bored waiting for responses. And that’s it. Nothing happens. I’ve of course tried with different services to no avail. Even played a little bit with that domain thing. Remember this is the same box. I tried on another computer, because this was a VM inside OSX, so I went ahead and tried on a “pure” win XP. Nothing. note: I have Apple Bonjour Service (up and running) and also the Apple SDK (installed later). Given that this didn’t work, I went ahead and decided to try the Apple SDK which has an Interop and a few pre-compiled samples (and its source code). Short story, neither the mDSNBrowser.exe nor the SimpleChat.exe work/see/discover anything. My box is a Win7 under Parallels, but that doesn’t seem to be affecting anything, given that the native XP exhibits the same problems. What am I doing so awfully wrong?

  Read the article

• Delayed_job: undefined method `handle_asynchronously' for #<Class:0x4601b08>

  - by KandadaBoggu

  After deploying DelayedJob as a gem, I got the following error: undefined method `handle_asynchronously' for #<Class:0x4601b08> Same code works when I deploy DelayedJob as a plugin. I have tried the solution suggested by this SO question and I still get the same error. I am using DelayedJob 1.8.4, Windows XP, Rails 2.3.5.

  Read the article

• AutoScaleMode problems with changed default font

  - by Doc Brown

  Hi, I have some problems with the Form.AutoScaleMode property together with fixed size controls, when using a non-default font. I boiled it down to a simple test application (WinForms 2.0) with only one form, some fixed size controls and the following properties: class Form1 : Form { // ... private void InitializeComponent() { // ... this.AutoScaleDimensions = new System.Drawing.SizeF(96F, 96F); this.AutoScaleMode = System.Windows.Forms.AutoScaleMode.Dpi; this.Font = new System.Drawing.Font("Tahoma", 9.25F); // ... } } Under 96dpi, Windows XP, the form looks correctly like this 96 dpi example. Under 120 dpi, Windows XP, the the Windows Forms autoscaling feature produces this 120 dpi example. As you can see, groupboxes, buttons, list or tree views are scaled correctly, multiline text boxes get too big in the vertical axis, and a fixed size label does not scale correctly in both vertical and horizontal direction. Seems to be bug in the .NET framework? Using the default font (Microsoft Sans Serif 8.25pt), this problem does not occur. Using AutoScaleMode=Font (with adequate AutoScaleDimensions, of course) either does not scale at all or scales exactly like seen above, depending on when the Font is set (before or after the change of AutoScaleMode). The problem is not specific to the "Tahoma" Font, it occurs also with Microsoft Sans Serif, 9.25pt. And yes, i already read this SO post http://stackoverflow.com/questions/2114857/high-dpi-problems but it does not really help me. Any suggestions how to come around this? EDIT: I changed my image hoster, hope this one works better. EDIT2: Some additional information about my intention: I have about 50 already working fixed size dialogs with several hundreds of properly placed, fixed size controls. They were migrated from an older C++ GUI framework to C#/Winforms, that's why they are all fixed-size. All of them look fine with 96 dpi using a 9.25pt font. Under the old framework, scaling to 120 dpi worked fine - all fixed size controls scaled equal in both dimensions. Last week, we detected this strange scaling behaviour under WinForms when switching to 120 dpi. You can imagine that most of our dialogs now look very bad under 120 dpi. We are looking for a solution that avoids a complete redesign all those dialogs.

  Read the article

• Autoloading Development or Production configs (best practices)

  - by Xeoncross

  When programming sites you usually have one set of config files for the development environment and another set for the production server (or one file with both settings). I am assuming all projects should be handled by version control like git or svn. Manual file transfers (like FTP) is wrong on so many levels. How you enable/disable the correct settings (so that your system knows which ones to use) is a problem for me. Each system I work on just kind of jimmy-rigs a solution. Below are the 3 methods I know of and I am hoping that someone can submit a more elegant solutions. 1) File Based The system loads a folder structure based on the URL requested. /site.com /site.fakeTLD /lib index.php For example, if the url is http://site.com then the system loads the production config files located in the site.com folder. However, if I'm working on the site locally I visit http://site.fakeTLD to work on the local copy of the site. To setup this I edit my hosts file and add site.fakeTLD to point to my own computer (127.0.0.1/localhost) and then create a vhost in apache. So now I can work on the codebase locally and then push to the server without any trouble. The problem is that this is susceptible to a "host" injection attack. So someone loading site.com could set the host to site.fakeTLD and then the system would load my development config files instead of production. 2) Config Based The config files contain on section for development - and one for production. The problem is that each time you go to push your changes to the repo you have to edit the file to specify which set of config options should be used. $use = 'production'; //'development'; This leaves the repo open to human error should one of the developers forget to enable the right setting. 3) File System Check Based All the development machines have an extra empty file called "development.txt" or something. Each time the system loads it checks for this file - if found then it knows it is in development mode - if missing then it knows it is in production mode. Since the file is NEVER ADDED to the repo then it will never be pushed (and checked out) on the production machine. However, this just doesn't feel right and causes a slight slow down since all filesystem checks are slow. Is there anyway that the server can auto-detect wither to use the development or production configs?

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• Soap Delphi Client end with a timeout for a 1MB call

  - by Cédric Girard

  Hi, we are developing a SOAP webservice (Apache/PHP). All run well for small size calls, but with a 1Mb soap call (the HTTPS call size is 1MB) our Delphi Soap client stop with a timeout on all PC but one, and our PHP clients run well with a default_socket_timeout=300, but stop with a "Error Fetching http headers" with default_socket_timeout=60. How can we change the timeout for Delphi? In fact this timeout seem to be in a Windows XP network library (wininet.dll called by soaphttptrans.pas) Thanks Cédric

  Read the article

• Measuring WPF Rendering Performance

  - by Wonko the Sane

  Hi All, I am looking to get some better performance on an ItemsControl, and I believe that the biggest hang-up is the rendering. The ItemTemplate of the control consists of (basically) a Border around an ImageBrush. The ItemsSource is an ObservableCollection of a custom class (of which I have no real control). What I'd like to know are some techniques for measuring (rudimentary measurements are fine to start with) the performance. This is an XP machine using .NET 3.5 SP1. Thanks, wTs

  Read the article

• Timing the Linux Kernel boot-time optimisation

  - by CVS-2600Hertz-wordpress-com

  I am trying to optimise the boot-up time of linux on an embedded device (not PC) Currently to profile the boot-up sequence, I have enabled the timing info on printk logs. Is this the most optimum way? If not, how do i profile the boot-up sequence (with timing) with minimum overhead? PS: I have a terminal (of the device) over a serial-connection & I use TeraTerm over windows-XP to access it.

  Read the article

• WPF ComboBox SelectedValue not updating from binding source.

  - by vg1890

  Here's my binding source object: Public Class MyListObject Private _mylist As New ObservableCollection(Of String) Private _selectedName As String Public Sub New(ByVal nameList As List(Of String), ByVal defaultName As String) For Each name In nameList _mylist.Add(name) Next _selectedName = defaultName End Sub Public ReadOnly Property MyList() As ObservableCollection(Of String) Get Return _mylist End Get End Property Public ReadOnly Property SelectedName() As String Get Return _selectedName End Get End Property End Class Here is my XAML: <Window x:Class="Window1" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Title="Window1" Height="300" Width="300" xmlns:local="clr-namespace:WpfApplication1" > <Window.Resources> <ObjectDataProvider x:Key="MyListObject" ObjectInstance="" /> </Window.Resources> <Grid> <ComboBox Height="23" Margin="24,91,53,0" Name="ComboBox1" VerticalAlignment="Top" SelectedValue="{Binding Path=SelectedName, Source={StaticResource MyListObject}, Mode=OneWay}" ItemsSource="{Binding Path=MyList, Source={StaticResource MyListObject}, Mode=OneWay}" /> <Button Height="23" HorizontalAlignment="Left" Margin="47,0,0,87" Name="btn_List1" VerticalAlignment="Bottom" Width="75">List 1</Button> <Button Height="23" Margin="0,0,75,87" Name="btn_List2" VerticalAlignment="Bottom" HorizontalAlignment="Right" Width="75">List 2</Button> </Grid> </Window> Here's the code-behind: Class Window1 Private obj1 As MyListObject Private obj2 As MyListObject Private odp As ObjectDataProvider Public Sub New() InitializeComponent() Dim namelist1 As New List(Of String) namelist1.Add("Joe") namelist1.Add("Steve") obj1 = New MyListObject(namelist1, "Steve") . Dim namelist2 As New List(Of String) namelist2.Add("Bob") namelist2.Add("Tim") obj2 = New MyListObject(namelist2, "Tim") odp = DirectCast(Me.FindResource("MyListObject"), ObjectDataProvider) odp.ObjectInstance = obj1 End Sub Private Sub btn_List1_Click(ByVal sender As System.Object, ByVal e As System.Windows.RoutedEventArgs) Handles btn_List1.Click odp.ObjectInstance = obj1 End Sub Private Sub btn_List2_Click(ByVal sender As System.Object, ByVal e As System.Windows.RoutedEventArgs) Handles btn_List2.Click odp.ObjectInstance = obj2 End Sub End Class When the Window first loads, the bindings hook up fine. The ComboBox contains the names "Joe" and "Steve" and "Steve" is selected by default. However, when I click a button to switch the ObjectInstance to obj2, the ComboBox ItemsSource gets populated correctly in the dropdown, but the SelectedValue is set to Nothing instead of being equal to obj2.SelectedName. Thanks in advance!

  Read the article

• Dreamweaver cs5 getting frozen on startup

  - by basit.

  every time i start dreamweaver cs5, it get stuck on initializing files, i cant even do end task on it. i tried giving administrator permission, try switching to xp compatible or vista, nothing works. anyone knows what can be the problem? i have attack the image on what it get stuck on.

  Read the article

• Adding custom perfomance counters in ASP.Net for service calls

  - by Nithin

  Hi All, I have to show the time taken for a service call in Perfmon from my ASP.Net application. For this, I have added a stopwatch which starts at the service call start and stops at service call stop. Now I have a custom counter which user AverageTimer32 to log the stopwatch values to Perfmon. My question is, how can I show the service names on the Perfmon graph. I am using windows XP (I know windows server perfmon has some fancy stuff).

  Read the article

• R: ESS shell.exec speed

  - by Musa

  I am using ESS in Windows XP. I have noticed that shell.exec is much slower with ESS than with RGui (the problem occurs when I try help(ls) for example, the help is displayed much faster in RGui, I tracked it down and it is due to shell.exec). Is there any reason for this? How can I fix it? My default browser is Firefox.

  Read the article

< Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >