Search Results

Search found 19471 results on 779 pages for 'network troubleshooting'.

Page 405/779 | < Previous Page | 401 402 403 404 405 406 407 408 409 410 411 412  | Next Page >

• How can I configure multiple default gateways on a CISCO Router?

  - by Spirit

  Does any one knows a way to configure a cisco router with multiple gateways - multiple gateways of last resort? I've tried adding a gateway of last resort twice (with different metric) but only one is shown: Router(config)# ip route 0.0.0.0 0.0.0.0 2.2.2.2 10 Router(config)# ip route 0.0.0.0 0.0.0.0 3.3.3.3 100 And the show ip route output was: Router# show ip route Gateway of last resort is 2.2.2.2 to network 0.0.0.0 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, FastEthernet0/0 3.0.0.0/24 is subnetted, 1 subnets C 3.3.3.0 is directly connected, FastEthernet0/1 32.0.0.0/30 is subnetted, 1 subnets C 32.2.2.0 is directly connected, Serial0/2/0 S* 0.0.0.0/0 [10/0] via 2.2.2.2 The point is that i cannot see the other route with higher distance metric? Anyone has a sugestion? I mean will this config work if the link on 2.2.2.2 fails? Will the router choose the other network 3.3.3.3, if the link 2.2.2.2 fails?

  Read the article

• MacOS creates a new mount on AFP path calls

  - by jAndy

  Hi Folks, following scenario: In my webapp, my customers are using Firefox as target browser. They have the need to open afp:// folders via Javascript. To make a long story short, this really works. You need to setup Firefox with about:config and set the value network.protocol-handler.external.afp to true. What happens then, the operating system (OSX) takes care of that path and it correctly opens a Finder window. The problem: OSX does create a new mount every time. It cannot distinct between afp://host/path/111 and afp://host/path/222 for instance. Furthermore, even if the afp path is 100% identical a new mount is created. It looks like this is the default behavior from OSX regardless of Firefox. So, is there any chance I can tell OSX not to create a new mount for some sub directorys which should get access over afp:// ? update: It looks like, there are OSX applications which can change the default behavior for network protocols. So you can change "somewhere" which application OSX should call for a protocol. If that is true, wouldn't it be possible to create a script which just opens the local path without a afp:// prefix ? The question here is, where is that configuration (?) to tell OSX which application to use for specific protocol. Any help welcome!

  Read the article

• Which upgrade path for disk IO bound postgres server?

  - by user41679

  Hi all, We currently have a Sun x4270 with 2xquad core Xeon Nehalmen 2.93ghz cores (16 threads), 72 gig of ram and 16 x 10k SAS disks split between the os raid 1, a partition for the Write Ahead Logs which is raid 10 and a partition for the database tables and indexes which is also raid 10, all xfs. I'm currently evaluating which path to go down in terms of upgrades. We'll be sharding the DB at some point soon, but for now I need to focus on hardware upgrades specifically. The machine is not CPU or memory bound at all at the moment, just IOWait is become an issue. The machine is mostly write access as we have a heavy caching layer. We're seeing about 300 write IOPS average on both the database partitions. We don't have any additional storage infrastructure like a Fiber Channel or ISCSI network. Budget isn't too much of a concern, something inline with the size of this server (i.e no $1m IBM machines) Space is ok on the DB side of things, we're running out obviously but there's also some reduction we can do. Additional space would be good though. My current thoughts are either: * ISCSI SAN, possible with 10Gbit network that has solid state acceleration. * FusionIO card / Sun F20 card (will the FusionIO card work in the Sun box? * DAS shelf (something like this http://www.broadberry.co.uk/das-direct-attached-storage-servers/cyberstore-224s-das) which a combination of 15k sas disks and some Intel X25-E drives for DB indexes etc) what would I need to put in the x4270 to add a DAS shelf? I think it's a SAS HBA card, do I have to use Sun's own card or will any PCI Express card work? Anything else??? what would you guys do from your experience? I appreciate it's a lot of questions, but I haven't expanded a DB machine for a number of years and the landscape has changed dramatically since then! Any advice or feedback would be very much appreciated. Let me know if there's anything else I can clarify. Thanks in advance!

  Read the article

• Unable to connect to FTP - Connection timeout after MLSD

  - by Afrosimon

  So here is my problem, I'm absolutely unable to connect to a FTP server, in circumstances I've never seen before. Here is the situation : I get a "Connection timed out" just after the MLSD command. I usually use Filezilla, under Ubuntu, but to make sure the problem isn't related to this particular client I tried a few others : gftp on ubuntu and winscp and freeftp on windows 7. All the same result. Also made sure to try with Active or Passive modes. Same result. At this point I would be inclined to think there is something wrong with my current network (furthermore, according to a coworker the FTP server is OK). But I did check with http://ftptest.net/ and I am able to get the directory listing (which I'm not able to through a FTP client). So in the end the last thing I didn't tried is to go on another network, solution which seems would work, but wouldn't be very practical in the long run. And thus I guess there's something wrong with my router... but what could it possibly be? Note : I did try to register and post this question on filezilla's board first... but I can't create an account with a gmail nor hotmail account. WTF?

  Read the article

• Domain workstation acting up and I can't track it down.

  - by DevNULL

  I have a developer with a Windows XP (SP2) 64 bit machine. If the machine is left on overnight (or any period of time longer than 5-6 hours) it takes 2-3 minutes to open any local drive and his network drives are no longer accessible. Here's what the system logs report... Any Help BTW: The problem just started a week ago and nothing has changed on the domain controller / AD or his machine. --- ERROR 1 Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 5719 Date: 6/8/2010 Time: 9:17:26 AM User: N/A Computer: BFC1 Description: This computer was not able to set up a secure session with a domain controller in domain UR due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. ADDITIONAL INFO If this computer is a domain controller for the specified domain, it sets up the secure session to the primary domain controller emulator in the specified domain. Otherwise, this computer sets up the secure session to any domain controller in the specified domain. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 5e 00 00 c0 ^..A --- ERROR 2 The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID {555F3418-D99E-4E51-800A-6E89CFD8B1D7} to the user NT AUTHORITY\LOCAL SERVICE SID (S-1-5-19). This security permission can be modified using the Component Services administrative tool. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. --- ERROR 3 Event Type: Error Event Source: RemoteAccess Event Category: None Event ID: 20106 Date: 6/8/2010 Time: 10:12:18 AM User: N/A Computer: BFC1 Description: Unable to add the interface {E76F0A78-7A0B-4EBB-A081-BA3BD452FC4C} with the Router Manager for the IP protocol. The following error occurred: Cannot complete this function. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: eb 03 00 00 e...

  Read the article

• Problem in accessing Windows shared folder on Ubuntu using terminal

  - by vikramtheone

  Hi Guys, Description I have 2 systems with me, one running on Windows(Host) and one on Ubuntu, both on a LAN. On the Windows(Host) I develop software intended for the Linux system and because the Linux system has little external memory, my idea to overcome this is by making the project folder on the Host side a Shared Folder with full access and access it on Ubuntu over the network. To achieve this, I have installed Samba on Ubuntu, when I go to Places -> Network I can see the shared project folder and I simply mount it. A link appears on the desktop. Next, using Nautilus I open the link and I can access the contents of the shared folder. Problem Even though I mount the shared project folder, I don't see it appearing in the /media or the /mnt folder, as a result of this I don't know what path to use to access this folder, from the terminal. For example: When, I mounted my USB stick, as expected, a link for the device appears on the Desktop and I also see a folder in the media folder. So, similarly, a mounted shared folder should have appeared on the /mnt folder, too. Can anyone suggest what I should do now? There are many posts around, but no solid solution for this problem. Help!!! :) Vikram

  Read the article

• VLAN setup on my PC

  - by Surjya Narayana Padhi

  Hi Geeks, I am bit new to VLAN. I want my two computers communicate through VLAN. I have following queries. As I am new to it my queries may be somewhat vague in some points. But i would like to hear from experts for my basic queries. I have two PCs Computer A and Computer B in two different IP networks Network A and Network B Both my PC has windows OS installed. How to send a VLAN(#Number) tagged packet from Computer A to Computer B and how to detect and untag the packet at Computer B? (Please provide the steps for windows OS) For this action do I need to check if my ethernet card supports VLAN tagging/untagging? If yes how can I know if my card supports it or not? Is the VLAN applied for Wireless ethernet controllers also? Do I need any switch or router for this action? Experts please given your inputs so that I can have a strong basic. If anyone can give some inputs how i can detect those VLAN in wireshirk, it will be helpful me also. Thanks in advance.

  Read the article

• EXCEL workbook, intermitently, takes 30 seconds to load

  - by Julio Nobre

  I am trying to figure out why a simple .XLS EXCEL workbook is taking, randomly, 30 seconds to open. Before answering: Please, bear mind the following: Problem symptoms Hanging is intermitent and it takes exactly 30 seconds; During hanging there is no cpu or disk activity; It only happens during workbook load. Every runs smooth after that; Windows Explorer.exe hangs on folder, but all other folders, system and applications are still responsive; There are no consecutive hangings. I have to wait for while to reproduce this behaviour; All workbooks where located on a local drive (C:\BPI); The workbook has no macros and no addins; Office 2003 is being used for several years; The computer is running Windows XP; Computer has several network mapped drives, all addressed to main file server; Recently, main fileserver was replaced by Windows 2011 SBS Standard Edition What I have done so far I have traced machine Explorer.exe, using Process Monitor, added Duration column, and filtered by Duration 1. That's is how I found that hanging was taking exactly 30 seconds. For further information, please refer to Oliver Salzburg tutorial. Using Process Monitor, I have also figured out than five operations were taking most of sample collecting duration. Looking at sample image below, column Operation below you will notice that one single operation was taking 29 seconds; I have tried different workbooks (all of them smaller than 30 KB); I have, temporarily, removed all shortcuts on User Document's folder that were pointing to network drives or shares; I have runned CCleaner to fix registry issues; I made sure that there were no external links on tested workbooks; I have reproduced this behaviour for hours; I have extensivelly researched for hours on the web; Process Monitor's collected and filtered data

  Read the article

• 2 servers on 2 networks in same office

  - by irot

  Hello Gents, My office doesn't have a "server guy" in employ, so I'm stuck with having to fix server issues for now. There are 2 servers in our office, both are file/web servers only accessible via LAN. They are currently on the same network, so no issue there. Problem is, we recently got a static IP to use, but it's with a different ISP, so now we have 2 routers in our office. I would like to open one of the servers to the public as a web/FTP server. But if I hook a server up to the new router, users will no longer be able to access the files shared on that server (because they're on different networks). How can I go about making one server accessible to the public using the static IP line, but still able to share the files on it to the users connected to the other network? The server I want to make public is running Windows Server 2008, the other server Windows Server 2003. And as far as I know, IP addresses are assigned by the router. I'm just a developer, don't know much about networking. Thank you in advance.

  Read the article

• SVN, Samba and Symbolic Links. How to get them all to play together?

  - by Camsoft

  I've got a website project under version control that relies on files from an unversioned directory on the same server via Symbolic Links. I'm currently storing the symbolic links in the repository. The idea is that if someone checks out a working copy on to the same server they can edit and test the working copy of the project before committing it back to the repository. When they checkout their working copy it successfully sets up the symlinks so that the entire site works when testing. The users that work on the project are Windows users, so I've set a samba shares on the server and then mapped them to network drives in Windows. People can edit their working copies directly on the server via network shares and then test them in the web browser before committing their changes back to the repository via TortoiseSVN. The Problem The problem I have is that Samba resolves the symlinks as expected but when a user tries to commit their changes back to the repository, TortoiseSVN thinks the linked files are part of the project and tries to commit the target files to the repository and not the symlinks themselves. I tried turning off symlink support in samba which means that the linked files cannot be resolved as I don't really want people to have access to the linked files nor do I want to import the linked files in the repository. The problem with this is that I get Can't stat '\webserver\projects\working\project\symlinked_file.php'. Access is denied Apart from the symlink problem everything else works 100% perfectly. Users can either checkout website projects to their machine and work on them (but can't test) or checkout them out to their space on the dev web server and work on them and fully test. So I don't want to change the workflow process, I just need a solution to the symbolic link issue. Many thanks. Originally posted on StackOverflow: http://stackoverflow.com/questions/2400917/svn-samba-and-symbolic-links-how-to-get-them-all-to-play-together

  Read the article

• WRT54GL Tomato Router in Client wireless mode to an iPhone Personal Hotspot

  - by Gordo

  I am trying to connect a router with Tomato firmware to an iPhone 4. The goal is to connect to the Personal Hotspot in Client Wireless mode. This should allow wired and wireless users to connect to the router rather then the iPhone. In theory this should be possible but I am having difficulty. Router Linksys WRT54GL Tomato 1.28.1816 firmware iPhone iPhone 4 iOS 5.1 (9B176) Carrier Rogers Wireless Personal Hotspot works with other devices, wifi/bluetooth/usb iPhone Personal Hotspot settings Mode: B/G Security: WPA or WPA2 Personal Encryption: AES Router IP: 172.20.10.1 Subnet: 172.20.10.0 Min IP: 172.20.10.2 Max IP: 172.20.10.14 maximum number of wireless tethered hosts is 5 I have followed the directions here: http://www.wi-fiplanet.com/tutorials/article.php/3810281 Ensured that the router subnet does not 'collide' with the iPhone subnet. Here is the configuration of the Tomato 'Basic - Network - Wireless' section: http://i.stack.imgur.com/pbmTB.png I have tried several variations of this configuration, but nothing seems to work. NOTE: I have successfully connected to my own wifi network in Wireless Client mode, so I am confident that there are no bad cables or other hardware issues. I would prefer to use Tomato, but DD-WRT maybe my only other option. Thanks!

  Read the article

• After connecting wlan0 to bridge interface (and then removing it), can't connect to AP

  - by gmonk

  I'm on a laptop running Debian Jessie with kernel 3.13-1-amd64; lspci shows that my wireless NIC + driver is 04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83) Subsystem: Intel Corporation Dual Band Wireless-AC 3160 Kernel driver in use: iwlwifi This has been working without any problems, until I tried creating a bridge for lxc containers to use. I did the same thing as this person here: How-to set up a network bridge on a laptop for LXC use? -- and ended up having the same problem as this poster did, so I decided to "undo" my actions. This hasn't been successful. Actions taken so far: To configure the bridge: #> ip link add type veth #> iw dev wlan0 set 4addr on #> ifconfig veth0 up #> brctl addbr br0 #> brctl addif br0 wlan0 #> brctl addif br0 veth0 #> ifconfig br0 192.168.0.4/24 #> ifconfig wlan0 0.0.0.0 To "deconfigure": #> brctl delif br0 wlan0 #> brctl delif br0 veth0 #> iw dev wlan0 set 4addr off #> ifconfig veth0 down #> ifconfig wlan0 down #> ifconfig br0 down #> brctl delbr br0 Now, dmesg and /var/log/syslog show repeated attempts at connecting to the AP that was working before, which fail after authentication: May 27 09:16:01 myhostname kernel: [11350.757172] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:01 myhostname kernel: [11350.759036] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:01 myhostname kernel: [11350.762615] wlan0: authenticated May 27 09:16:01 myhostname kernel: [11350.762753] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.762755] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.765080] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:01 myhostname kernel: [11350.767474] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:01 myhostname kernel: [11350.767476] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:01 myhostname kernel: [11350.788475] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:02 myhostname dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14 May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname kernel: [11354.559579] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.561458] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> associating May 27 09:16:04 myhostname kernel: [11354.563445] wlan0: authenticated May 27 09:16:04 myhostname kernel: [11354.563631] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.563633] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.565727] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.568091] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:04 myhostname kernel: [11354.569030] wlan0: associated May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:05 myhostname kernel: [11354.978204] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:05 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:05 myhostname kernel: [11354.992729] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:05 myhostname kernel: [11354.995004] cfg80211: World regulatory domain updated: May 27 09:16:05 myhostname kernel: [11354.995005] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:05 myhostname kernel: [11354.995006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995008] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995009] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995010] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.763968] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:09 myhostname kernel: [11358.765796] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.769957] wlan0: authenticated May 27 09:16:09 myhostname kernel: [11358.770102] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770104] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770846] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname kernel: [11358.773358] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:09 myhostname kernel: [11358.773361] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:09 myhostname kernel: [11358.802187] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.573442] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.575270] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.580334] wlan0: authenticated May 27 09:16:12 myhostname kernel: [11362.580503] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.580516] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.583508] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.585908] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:12 myhostname kernel: [11362.586781] wlan0: associated May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:13 myhostname kernel: [11362.947693] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:13 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:13 myhostname kernel: [11362.973461] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:13 myhostname kernel: [11362.975673] cfg80211: World regulatory domain updated: May 27 09:16:13 myhostname kernel: [11362.975675] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:13 myhostname kernel: [11362.975676] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975677] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0/wireless): association took too long. May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: config -> failed (reason 'no-secrets') [50 120 7] May 27 09:16:14 myhostname NetworkManager[13992]: <info> Marking connection 'Auto myaccesspoint' invalid. May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0) failed for connection 'Auto myaccesspoint' May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): deactivating device (reason 'none') [0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> disconnected The things that jump out at me are "deauthenticating ... by local choice( reason=3)" and the lines that contain "(reason=15)". I've tried various fixes: iwconfig wlan0 power off killing wpa_supplicant connecting with iwconfig + dhclient instead of gnome's network -manager explicitly configuring wlan0 in /etc/network/interfaces creating a /etc/wpa_supplicant.conf file ...but nothing seems to work. I'm not sure what I did wrong, or what step I've skipped in trying to get wlan0 back as a non-bridged device -- I removed it from the bridge and then deleted the bridge itself. Any ideas?

  Read the article

• What steps should I take to debug this non-starting hvm virtual machine?

  - by Ophidian

  I have a dom0 machine running CentOS 5.4 with all the latest updates using Xen as my hypervisor. I am using Xen in part because this machine was set up prior to KVM being included in RHEL, and in part because KVM's network bridging configuration is not nearly as simple as Xen's. The dom0 machine is headless and I do all of my VM management via virsh from the command line. I have two hvm domU's: A web server running CentOS 5.4 A mail server running Gentoo Both VM's are backed by LV's on the dom0 but do not use LVM in the domU. Both have virtually identical libvirt configurations (differing by expected things like name, UUID, NIC MAC, VNC port, etc). The web server domU (WSdomU hereafter) does not start since applying the most recent kernel update (kernel-xen-2.6.18-164.15.1.el5.x86_64 and kernel-2.6.18-164.15.1.el5.x86_64 for the dom0 and WSdomU respectively). By 'not start' I mean it appears to be running but it does not use an CPU cycles, does not bring up a graphical console, and does not respond on the network. The WSdomU is listed as no state rather than the normal running or blocked in xentop. The mail server domU starts fine and functions normally. Here are the steps I have taken so far that did not solve the problem: Reboot the dom0 to see if things come up on their own Check xen dmesg on dom0 Check xend logs (a cursory viewing did not show anything blatant; specific suggestions of things to look for would be appreciated) Attempted to connect to the WSdomU's graphical (VNC) console from the dom0 Shutdown the mail server domU and attempt to start the WSdomU Check the SELinux labels on backing LV's (they're the same) Set SELinux to permissive and attempt to start the WSdomU Use virsh edit to try tweaking the WSdomU config virsh undefine, reboot, virsh define the WSdomU config dd the WSdomU LV to an .img file, copy it to my Fedora desktop and run it under KVM (works fine) What steps should I take next to debug this? I will edit in any additional configuration's requested in the comments.

  Read the article

• Very slow connection to xserve via afp or smb

  - by Mhoffman13

  Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

  Read the article

• Netflix streaming stops loading at 98% on Revo 3700

  - by Martin Harris

  I'm trying to stream Netflix on an Acer Revo 3700 running Windows 7 Home Premium, but it hangs on the loading screen at 98% (after it has formatted the player to the right aspect ratio and added the controls, but before the video starts) with no error messages or failures. I have two other machines on the same network, one running Windows 7 Home Premium and another running XP, which both stream faultlessly. Things I have tried: Both a wired and wireless connection to the router Upgrading the video and audio drivers IE, Chrome and Firefox Boxee software Connecting with a VGA cable instead of HDMI (in case it is a HDCP thing) Uninstalling and reinstalling Silverlight. Getting someway into loading a HD movie and turning "Allow HD" off Does anyone know what Netflix is doing at the 98% load mark? Are there any log files? Anything else worth trying? Full disclosure: I'm using Netflix from the UK through a US based VPN. I've tried multiple VPNs and the problem is exactly the same, also the other machines on the same network through the same VPN work fine so I don't think this is the issue, but it might be a factor. The region check happens at around 7% and I get past that.

  Read the article

• VLAN Tagging Traffic on Cisco Switch

  - by David W

  I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

  Read the article

• libvirt's dnsmasq does not respond to dns queries or provide dhcp

  - by Jeremy

  This is on Ubuntu 10.04 server, using KVM to run Ubuntu guests. This system has been working for a long time and I have not changed anything (other than applying security updates), but today I found dnsmasq no longer responds to requests. I cannot say how long this has been broken for me because I don't frequently use the NAT'd guests. So it could have started just after the last updates or some other event and I just now found it. I can connect to port 53 with telnet at 192.168.122.1. I've flushed ip-tables to be sure it wasn't firewall rules and that is not the problem. dnsmasq is running, virsh reports default network as stared. I can't find ANY information on troubleshooting libvirt dnsmasq except that it won't play well with other instances of dnsmasq, which is not the problem. I cannot even find where log entries might be for this service. Any ideas on where to look for more information? edit to add: I added another network and that one works fine. I guess I have a workaround but would still like to figure out how to troubleshoot this problem.

  Read the article

• Intermittent 5.7.1 email bounce to Exchange 2007

  - by Steve Kennaird

  My knowledge of Exchange isn't particularly great, so excuse me if some of the terminology I use isn't quite right. I'm primarily a web developer who's now responsible for a small business's network. We have a server running SBS 2008 and Exchange 2007. Generally, everything works well, emails are able to be sent to both internal and external domains without issue. We've only got ~20 users, Exchange is sitting on a single server. I use SendGrid to send emails generated by our externally hosted website to users in the office. Primarily, order notifications are sent to [email protected]. Without any pattern and less than once per week on average, an email to [email protected] will bounce back, and the logs on SendGrid detail the following error: 550 5.7.1 Unable to relay for [email protected] Either side of that failed delivery attempt, I'm able to send and receive emails to/from [email protected]. Having done some research, incorrect reverse DNS seems like it could be a cause of intermittent bounces like this. Having used nslookup, I have found that the reverse DNS doesn't map like it should, e.g. Office IP: 135.325.351.123 (made up IP, for example only) Domain: office.somedomain.com (made up, for example only) Reverse DNS: somedomain.gotadsl.co.uk (half made up) Could this be a cause? I'm sure that the IP address and the domain should map to each other. Also, it has been suggested to me that as the Exchange server is on a network with an ADSL connection, that could be a potential cause as the connection "goes up and down all day long". I don't have an opinion on this, as I don't have enough knowledge of Exchange/ADSL to form a reliable opinion. Can anyone offer any insight as to whether one or both are actually potential causes, or if there is another possible cause?

  Read the article

• Terminal Server in Windows Server 2003

  - by Hemal

  I have a confusion regarding what I am doing here. At present I have a Windows Server 2003 server with SP2. I have assigned RAS/VPN server role to it (through Manage my server wizard) and in my router, I setup the IP address of my RAS/VPN server as PPTP server. Staff leave their workstations ON all the time and access them from home through RDP. They first connect thorugh VPN & in the RDC they simply type their respective IP or computer name to access the office network from home. Everything works fine so far except: Staff have to leave compuers always ON in the office Speed is very slow depend how many staff members access the VPN network I was told to install and configure Terminal service to improve this situation. I already added TS Role in the server but I don't know how to clients can access the TS server from home or remote location. I really appreciate any good links or guidence from the experts in this group regarding this. Thank you in advance for any replies!

  Read the article

• Default IPv6 route on debian squeeze does not come up after boot

  - by Georg Bretschneider

  I have a problem with my default IPv6 route not coming up after boot on a Debian Squeeze system. This is my config (/etc/network/interfaces): # Loopback device: auto lo iface lo inet loopback iface lo inet6 loopback # device: br0 auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 88.198.62.xx broadcast 88.198.62.63 netmask 255.255.255.224 gateway 88.198.62.33 up route add -net 88.198.62.32 netmask 255.255.255.224 gw 88.198.62.33 br0 iface br0 inet6 static address 2a01:4f8:131:10x::2 netmask 64 gateway 2a01:4f8:131:100::1 up route -A inet6 add 2a01:4f8:131:100::1/59 dev br0 My inet comes up alright, but I have to exec the route command manually after boot to make IPv6 work. Otherwise I can't even reach my gateway. This is the output of ip -6 route show after boot: 2a01:4f8:131:10x::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 unreachable fe80::/64 dev lo proto kernel metric 256 error -101 mtu 16436 advmss 16376 hoplimit 4294967295 fe80::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 I already tried it with: up ip -6 route add 2a01:4f8:131:100::1 dev br0 up ip -6 route add default via 2a01:4f8:131:100::1 dev br0 in /etc/network/interfaces, but with the same results. If I execute those commands manually on my shell, everything starts working nicely. And yes, I tried with post-up instead of up, too. Only other changes I made was to activate ip forwarding for IPv6, because I want to run some LXC containers on that system.

  Read the article

• Cannot Connect To VMWare Guest OS Using Either RDP or VNC

  - by Humanier

  I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve the mentioned problems.

  Read the article

• Deleted printers keeps coming back - and multiply

  - by MojoDK

  My users are on 2012 R2 RDS Session Host servers. I've used "Deploy Printers" (from Print Manager) to deploy 4 printers. The last week, I've had a lot of problems where users can't print. If I deleted the printer and added it again, they could print just fine. Now I've removed all printer deploying from GPO - and I have no printers in any login scripts. I did a gpupdate /force, but all the 4 printers are now listed 3 times... If I delete the printers and log off and back on, all the printers are popping up again. Sigh! This is driving me nuts. This script doesn't show any of the "SVFREJA" printers... Set objWMIService = GetObject("winmgmts:\\.\root\cimv2") Set colPrinters = objWMIService.ExecQuery ("Select * From Win32_Printer") If colPrinters.Count <> 0 Then 'If there are some network printers Dim s s = "" For Each objPrinterInstalled In colPrinters ' For each network printer s = s + objPrinterInstalled.Name + chr(13) Next msgbox s End if It gives me this result... (sry for the big picture) My problem is not with the "redirected" printers, my problem is that I have several printers with the same name (on SVFREJA) and I can't get rid of them. Any idea why I can't get rid of the "ophaned" printers??

  Read the article

• Failure to obtain IP with ARP over Wi-Fi with personal Wi-Fi router in client mode

  - by axk

  I'm trying to connect a Samsung TV to the Internet using a TL-MR3020 personal wireless router in client mode. The TV fails to connect to the network. It sees the ethernet cable connected though. Here's my network topology: Here's what I've captured with Wireshark filtering for ARP (eth.type == 0x0806): It appears the TV fails to get the IP of the gateway (DSL modem/router) for some reason. One thing I've noticed is that the source MAC for the ARP requests coming from the TV is the MAC of the Portable wireless router (that is cd:89:00), not the TV itself and the modem sends the responses to that MAC (I'm not an expert and don't know if its okay or it may make the TV fail to get the requested IP). Also I'm able to ping the TV from the DSL router (through the telnet interface) and the router has an entry in its MAC table for the TV's IP with the Portable wireless router's MAC (that is cd:89:00). If I'm able to ping the TV I suppose it should know the router's MAC to respond to the ping, but then why these continuous ARP requests... I've also tried to connect my desktop trough this Portable wireless router the same way I'm trying to connect the TV and it works fine, I can set the DSL Modem's IP as the default gateway on the desktop's NIC and connect to the Internet. The TV can connect to the Internet when connected to the DSL Router with a wired connection. Any suggestions on what may be the cause of the problem / how to further debug it are welcome. Thanks!

  Read the article

• VPN on a ubuntu server limited to certain ips

  - by Hultner

  I got an server running Ubuntu Server 9.10 and I need access to it and other parts of my network sometimes when not at home. There's two places I need to access the VPN from. One of the places to an static IP and the other got an dynamic but with DynDNS setup so I can always get the current IP if I want to. Now when it comes to servers people call me kinda paranoid but security is always my number one priority and I never like to allow access to the server outside the network therefor I have two things I have to have on this VPN. One it shouldn't be accessiable from any other IP then these 2 and two it has to use a very secure key so it will be virtually impossible to bruteforce even from the said IP´s. I have no experience what so ever in setting up VPNs, I have used SSH tunneling but never an actuall VPN. So what would be the best, most stable, safest and performance effiecent way to set this up on a Ubuntu Server? Is it possible or should I just set up some kind of SSH Tunnel instead? Thanks on beforehand for answers.

  Read the article

• Apache runs in console but not as a service?

  - by danspants

  I have an apache 2.2 server running Django. We have a network drive T: which we need constant access to within our Django app. When running Apache as a service, we cannot access this drive, as far as any django code is concerned the drive does not exist. If I add... <Directory "t:/"> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> to the httpd.conf file the service no longer runs, but I can start apache as a console and it works fine, Django can find the network drive and all is well. Why is there a difference between the console and the service? Should there be a difference? I have the service using my own log on so in theory it should have the same access as I do. I'm keen to keep it running as a service as it's far less obtrusive when I'm working on the server (unless there's a way to hide the console?). Any help would be most appreciated.

  Read the article

< Previous Page | 401 402 403 404 405 406 407 408 409 410 411 412  | Next Page >