Search Results

Search found 12484 results on 500 pages for 'host'.

Page 406/500 | < Previous Page | 402 403 404 405 406 407 408 409 410 411 412 413  | Next Page >

• Vlans and subinterfaces

  - by Adeodatus

  I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

  Read the article

• Postfix (delivery temporarily suspended: conversation with mydomain.net [private/lmtp] timed out while receiving the initial server greeting)

  - by Paul

  I'm running Debian 7.1, Postfix version 2.9.6, Dovecot Version 2.1.7 To set it up I followed mostly this (without the spamass-clamav-greylist bit) I have also got setup smart host relaying via gmail postconf -n reveals: alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all inet_protocols = ipv4 mailbox_size_limit = 0 milter_default_action = accept mydestination = MyDomain, localhost.net, localhost myhostname = MyDomain.net mynetworks = 127.0.0.0/8 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relay_domains = mysql:/etc/postfix/mysql_relay_domains.cf relayhost = [smtp.gmail.com]:587 smtp_connect_timeout = 120s smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/relay_passwd smtp_sasl_security_options = noanonymous smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_non_fqdn_hostname, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unauth_destination, reject_unauth_pipelining, reject_invalid_hostname smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes virtual_alias_maps = mysql:/etc/postfix/mysql_virtual_alias_maps.cf virtual_gid_maps = static:3000 virtual_mailbox_base = /home/vmail virtual_mailbox_domains = mysql:/etc/postfix/mysql_virtual_mailbox_domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql_virtual_mailbox_maps.cf virtual_transport = lmtp:unix:private/lmtp virtual_uid_maps = static:3000 I am able to send emails to the outside world but all emails sent to me are getting stuck. mailq is showing numerous lines: A69C2414C4 2621 Fri Dec 27 14:57:03 [email protected] (conversation with MyDomain.net[private/lmtp] timed out while receiving the initial server greeting) [email protected] AB78B414BE 3796 Fri Dec 27 14:56:50 [email protected] (delivery temporarily suspended: conversation with MyDomain.net[private/lmtp] timed out while receiving the initial server greeting) [email protected] /var/log/mail.log is showing: Dec 28 09:50:09 hostname postfix/lmtp[10828]: E947C414CD: to=, relay=localhost[private/lmtp], delay=64012, delays=63712/0.25/300/0, dsn=4.4.2, status=deferred (conversation with localhost[private/lmtp] timed out while receiving the initial server greeting) Any help would be greatly appreciated. Thank you

  Read the article

• How to tell statd to use portmap on a non-localhost ipadress?

  - by jneves

  How can I make statd connect to other IP address other than 127.0.0.1? I have a server that is connected to 2 different networks (one is public, another a private). I want it to provide a NFS share for only the private network. The host in an ubuntu 8.04. The private ip address is 192.168.1.202 I changed /etc/default/portmap to add: OPTIONS="-i 192.168.1.202" The command lsof -n | grep portmap returns: portmap 10252 daemon cwd DIR 202,0 4096 2 / portmap 10252 daemon rtd DIR 202,0 4096 2 / portmap 10252 daemon txt REG 202,0 15248 13461 /sbin/portmap portmap 10252 daemon mem REG 202,0 83708 32823 /lib/tls/i686/cmov/libnsl-2.7.so portmap 10252 daemon mem REG 202,0 1364388 32817 /lib/tls/i686/cmov/libc-2.7.so portmap 10252 daemon mem REG 202,0 31304 16588 /lib/libwrap.so.0.7.6 portmap 10252 daemon mem REG 202,0 109152 16955 /lib/ld-2.7.so portmap 10252 daemon 0u CHR 1,3 960 /dev/null portmap 10252 daemon 1u CHR 1,3 960 /dev/null portmap 10252 daemon 2u CHR 1,3 960 /dev/null portmap 10252 daemon 3u unix 0xecc8c3c0 4332992 socket portmap 10252 daemon 4u IPv4 4332993 UDP 192.168.1.202:sunrpc portmap 10252 daemon 5u IPv4 4332994 TCP 192.168.1.202:sunrpc (LISTEN) portmap 10252 daemon 6u REG 0,12 289 3821511 /var/run/portmap_mapping I defined in /etc/hosts the following: 192.168.1.202 server.local In /etc/default/nfs-common I changed STATDOPTS to: STATDOPTS="--name server.local" Yet when I run /etc/init.d/nfs-common start if fails to start. The log shows: Jun 8 06:37:44 cookwork-web1 rpc.statd[9723]: Version 1.1.2 Starting Jun 8 06:37:44 cookwork-web1 rpc.statd[9723]: Flags: Jun 8 06:37:44 cookwork-web1 rpc.statd[9723]: unable to register (statd, 1, udp). An strace -f rpc.statd -n server.local results in a lot of lines, including this one: sendto(9, "\200]3\362\0\0\0\0\0\0\0\2\0\1\206\240\0\0\0\2\0\0\0\1"..., 56, 0, {sa_family=AF_INET, sin_port=htons(111), sin_addr=inet_addr("127.0.0.1")}, 16) = 56

  Read the article

• Wastage of resources in Virtualization

  - by Sabeen Malik

  I have asked this question on SO, but was suggested that i ask it here on SF, so here it goes. http://stackoverflow.com/questions/3010753/wastage-of-resources-in-virtualization I am not sure if this is the right place to ask the question. However i hope it is. When looking for a VPS earlier today, I was trying to understand how each container would work in the background. Keeping in mind the fact that the operating system uses most of the memory and power on a system, wouldn't having multiple operating systems in the same machine mean more wastage of resources. For instance if i was running centOS on a dedicated box and it was running lets say 20 background OS level processes. Then i go and install a virtualization platform and install 5 more centOS virtual machines in the same system which are exactly the same as the host operating system. Doesn't this mean duplication of those 20 processes 6 times? So internally the context switching is happening between 120 processes instead of 20? Further Notes: Here is an example of what i am thinking: I have a master-slave configuration for a long running, cpu + memory intensive process, which can be distributed to 4 machines. Lets say when the process runs on these 4 machines with lets say 1 Gh CPU and 1 Gig RAM, i get 400 results per hour from the cluster (assuming 100 results from one machine) . Now i get a bigger machine ( lets say 4Gh and 4 Gig RAM), have 4 virtual hosts on it with 1 Gz CPU and 1 Gig RAM. Will this configuration give me the same 4 results per hour from these 4 virtual hosts?

  Read the article

• Oracle 10g for Windows does not start up on system boot

  - by Mike Dimmick

  We have an Oracle 10g Enterprise Edition installation (10.2.0.1.0) on a Windows Server 2003 virtual machine. It was initially created with Virtual Server 2005 R2 SP1 but has now been migrated to Windows Server 2008 Hyper-V. The services start on system boot, but the instance does not start up. This problem was actually occurring on Virtual Server after a migration from one server to another, but I managed to fix it then with: oradim -edit -sid ORCL -startmode auto However, this now has no effect. oradim.log (in %OracleHome%\database\oradim.log) says: Thu Jun 10 14:14:48 2010 C:\oracle\product\10.2.0\db_3\bin\oradim.exe -startup -sid orcl -usrpwd * -log oradim.log -nocheck 0 Thu Jun 10 14:14:48 2010 ORA-12560: TNS:protocol adapter error sqlnet.log in the same folder has: Fatal NI connect error 12560, connecting to: (DESCRIPTION=(ADDRESS=(PROTOCOL=BEQ)(PROGRAM=oracle)(ARGV0=oracleorcl)(ARGS='(DESCRIPTION=(LOCAL=YES)(ADDRESS=(PROTOCOL=beq)))'))(CONNECT_DATA=(SID=orcl)(CID=(PROGRAM=C:\oracle\product\10.2.0\db_3\bin\oradim.exe)(HOST=ORACLE-VM)(USER=SYSTEM)))) VERSION INFORMATION: TNS for 32-bit Windows: Version 10.2.0.1.0 - Production Oracle Bequeath NT Protocol Adapter for 32-bit Windows: Version 10.2.0.1.0 - Production Time: 10-JUN-2010 14:14:48 Tracing not turned on. Tns error struct: ns main err code: 12560 TNS-12560: TNS:protocol adapter error ns secondary err code: 0 nt main err code: 530 TNS-00530: Protocol adapter error nt secondary err code: 2 nt OS err code: 0 The ORA_ORCL_AUTOSTART registry value is set to TRUE, so it should be auto-starting - and you can see that it's trying to. The problem also occurs when stopping and restarting the OracleServiceORCL service. I've enabled SQL*Net tracing which shows: [10-JUN-2010 15:09:33.919] snlpcss: entry [10-JUN-2010 15:09:34.419] snlpcss: Unable to spawn Oracle oracle (DESCRIPTION=(LOCAL=YES)(ADDRESS=(PROTOCOL=beq))) orcl, error 2. [10-JUN-2010 15:09:34.419] snlpcall: exit On a hunch that error 2 is Windows error 2 (file not found) I tried restarting the service with Process Monitor watching oradim.exe, but this appears to delay things just enough that it always works. Right now I have a horrible hack where I've created a Scheduled Task to run oradim -startup -sid ORCL when the Administrator account logs on, and set the VM to auto-logon. I'd still like to work out why it's not working.

  Read the article

• wget is working only when used with sudo

  - by Yusuf

  I'm having quite a strange behavior with wget since yesterday. I can download files by using sudo wget, but when I try the same file with only wget, I can get this error: yusufh@ubuntu-yuh:~$ wget http://www.kegel.com/wine/winetricks --2010-12-17 09:34:11-- http://www.kegel.com/wine/winetricks Resolving www.kegel.com... failed: Name or service not known. wget: unable to resolve host address `www.kegel.com' and with sudo wget: yusufh@ubuntu-yuh:~$ sudo wget http://www.kegel.com/wine/winetricks --2010-12-17 09:35:37-- http://www.kegel.com/wine/winetricks Connecting to 127.0.0.1:5865... connected. Proxy request sent, awaiting response... 200 OK Length: 190672 (186K) [text/plain] Saving to: `winetricks' 100%[==================================================================================================>] 190,672 --.-K/s in 0.03s 2010-12-17 09:35:37 (6.92 MB/s) - `winetricks' saved [190672/190672] After the comments below, here is an update: I can use Google Chrome or Firefox perfectly without running it as root. I use ntlmaps to connect to the office proxy. So I need to use 127.0.0.1:5865 as the proxy for clients. Result for env | grep -i proxy: NO_PROXY=localhost,127.0.0.0/8,*.local, http_proxy=127.0.0.1:5865 ftp_proxy=127.0.0.1:5865 all_proxy=socks://127.0.0.1:5865/ ALL_PROXY=socks://127.0.0.1:5865/ https_proxy=127.0.0.1:5865 no_proxy=localhost,127.0.0.0/8,*.local while sudo env | grep -i proxy is empty! HELP!

  Read the article

• Msg 10054, Level 20, State 0, Line 0 Error when altering a stored procedure to add a couple of curso

  - by doug_w

  We have a home-rolled backup stored procedure that uses xp_cmdshell to create and clean up database backups. We have an instance that is 2005 sp3 that we are trying to deploy this script to. I am at a bit of a loss for why it is not working. When I execute the create it runs for about 30 seconds and yields the following error: Msg 10054, Level 20, State 0, Line 0 A transport-level error has occurred when sending the request to the server. (provider: TCP Provider, error: 0 - An existing connection was forcibly closed by the remote host.) In my tinkering I discovered that by removing the cursors that actually do the work it will allow me to create the stored procedure (not very helpful for me though). If I add the cursors back in using an alter the error returns. I would be curious if someone has experienced this problem and knows of a solution or work around. I am not opposed to posting the source, it is just lengthy. Things I have checked: Error Logs No dump files in the log directory Thanks in advance for the help.

  Read the article

• Force Juniper-network client to use split routing

  - by craibuc

  I'm using the Juniper client for OSX ('Network Connect') to access a client's VPN. It appears that the client is configured to not use split-routing. The client's VPN host is not willing to enable split-routing. Is there a way for me to over-ride this configuration or do sometime on my workstation to get the non-client network traffic to by-pass the VPN? This wouldn't be a big deal, but none of my streaming radio stations (e.g. XM) work will connected to their VPN. Apologies for any inaccuracies in the terminology. ** edit ** The Juniper client changes my system's resolve.conf file from: nameserver 192.168.0.1 to: search XXX.com [redacted] nameserver 10.30.16.140 nameserver 10.30.8.140 I've attempted to restore my preferred DNS entry to the file $ sudo echo "nameserver 192.168.0.1" >> /etc/resolv.conf but this results in the following error: -bash: /etc/resolv.conf: Permission denied How does the super-user account not have access to this file? Is there a way to prevent the Juniper client from making changes to this file?

  Read the article

• Forward real IP through Haproxy => Nginx => Unicorn

  - by Hendrik

  How do I forward the real visitors ip adress to Unicorn? The current setup is: Haproxy => Nginx => Unicorn How can I forward the real IP address from Haproxy, to Nginx, to Unicorn? Currently it is always only 127.0.0.1 I read that the X headers are going to be depreceated. http://tools.ietf.org/html/rfc6648 - how will this impact us? Haproxy Config: # haproxy config defaults log global mode http option httplog option dontlognull option httpclose retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 # Rails Backend backend deployer-production reqrep ^([^\ ]*)\ /api/(.*) \1\ /\2 balance roundrobin server deployer-production localhost:9000 check Nginx Config: upstream unicorn-production { server unix:/tmp/unicorn.ordify-backend-production.sock fail_timeout=0; } server { listen 9000 default; server_name manager.ordify.localhost; root /home/deployer/apps/ordify-backend-production/current/public; access_log /var/log/nginx/ordify-backend-production_access.log; rewrite_log on; try_files $uri/index.html $uri @unicorn; location @unicorn { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_redirect off; proxy_pass http://unicorn-production; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; } error_page 500 502 503 504 /500.html; client_max_body_size 4G; keepalive_timeout 10; }

  Read the article

• Nginx, HAproxy, Unicorn, Rails and Node settings

  - by Julien Genestoux

  Our application is currently only a "regular" web app, with no fancy things like streaming HTTP or websockets. It's mostly a Rails app, served by a few (20 on 2 machines) Unicorn workers, proxied by a venerable nginx server which deals with load balancing. This has been working quite well for the past year and the app now serves between 400 and 800 requests per second at any point during the day. We're soon releasing 2 new APIs, which are both served by a Node application : a websocket one, as well as a long polling HTTP one. (the fancy thing like the Twitter streaming API where HTTP connections never end). They both use the same port on node and since the node app is stateless, we can certainly deploy a few of them to handle the traffic. The app (node) is now deployed in 5 instances and are now listening on 5 different 'private' ports on the same host. We need to put something in front of them to load balance, but also something that is able to deal with sockets (either websocket or HTTP streaming) which are intended to stay 'up' for days. The question is then : what? I read somewhere that HAProxy does a better job than Nginx at this. What do you recommend?

  Read the article

• SSD seems dead after wakeup from Windows Sleep, BIOS stalls but doesn't find it anymore

  - by Abel

  The morning, the following scary scenario happened: I woke up my Windows system Typed in my username and got an error (something like "could not load security xxx", but unsure of exact wording) System auto-restarted after cliking OK It didn't boot up anymore to the SSD with Windows 7 OS (I have another disk I can boot to, but that doesn't see the disk either). Obviously, this happened right after I instantiated a backup procedure, which hasn't succeeded either. The BIOS can't find the drive when I connect to SATA. And it can't find the drive when I connect it to SAS. I have a Dell Workstation T7400, most recent BIOS (version A06), version of SAS Host Bus Adapter BIOS (HBA) is MPTBIOS 6.14.10.00 (2007.09.29) from LSI Logic Corp. Other findings: When connecting to SATA, the DELL Logo screen stays really long (5 minutes) and then at the end of POST it says that a drive is not found When connecting to SAS, the SAS HBA initializing phase takes long (2 minutes, against normally 15 seconds) When running Dell Diagnostics, it doesn't finish and gives the error Exception occurred in module MPCACHE.MDM file "IOAPICSP.ASM" line 1645. I contacted Dell. On their advice I tried different slots and different cables to no avail. I use an APIC battery power, spikes in the power are thus unlikely. My conclusion so far: the disk is dead. I need this disk very badly because it contains the last few days of important development of which not all code was checked in the moment this happened. Are there any ways to recover dead SSD drives? The drive is a new X25-M G2 160GB model SSDSA2M160G2GC 2.5" in an extension bay and has been running without issues for 3 months on SAS.

  Read the article

• ports only available from the outside network

  - by ChrisJ

  This is a counter-intuitive problem for me. I have a new Win 2003 server on a static IP address w.x.y.z. Tomcat 7, PostgreSQL 9.1, and Subversion are installed. All of it appears to be working fine from the server itself. We can also access the Tomcat manager, web applications, and run "svn ls svn://w.x.y.z/" from outside our network. However, when I try from another machine in the office, phpPgAdmin and svn cannot establish connections with the server. http://w.x.y.z:5432/phppgadmin cannot connect. The svn command from above returns: svn: E730061: Unable to connect to a repository at URL 'svn://w.x.y.z/' svn: E730061: Can't connect to host 'w.x.y.z': No connection could be made because the target machine actively refused it. Tomcat manager and the other web apps we have deployed work fine. Netstat -a from the server shows this: Proto Local Address Foreign Address State TCP SERVERNAME:3690 SERVERNAME:0 LISTENING TCP SERVERNAME:5432 SERVERNAME:0 LISTENING Windows Firewall was off, but just in case I also tried to enable it and open ports 3690 (svn) and 5432 (postgres). No change. I don't have access to the router/switch because it just doesn't work that way in Port-au-Prince and our sysadmin is on R&R. Is there anything that might be causing the problem from the server side?

  Read the article

• Port forwarding + shared connection with Ubuntu

  - by Joey Adams

  Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

  Read the article

• Delete ARP cache on Mac OS when moving from one Wifi network to the other

  - by Puneet

  I am facing wireless connectivity problems when I move from one Wifi network to the other. Here is how it happens: I am at my friends place. I connect to his Wifi. His Wifi router ip address is 192.168.0.1. Everything is fine I close my laptop, come back to my house, open my laptop and I connect to the Wifi Network at my place. Different ESSID, but the Wifi router address is the same 192.168.0.1. At this point I cant get to anything on the internet. To debug I try to see if I can ping the router (192.168.0.1), I cant. I get a no route to host. Meanwhile airport tells me Im connected to Wifi. I see the arp cache and I see a permanent entry for 192.168.0.1 ? (192.168.0.1) at 5c:d9:98:65:73:6c on en1 permanent [ethernet] This permanent bit looks problematic. I go ahead and delete the arp cache entry and all is fine with the world until I go back to my friends place where the same situation plays out. Now my question is, why the hell is this happening? If there is no way around it, can I run a script on Wifi connect/disconnect to clear out the arp cache? Im using Mac OS X $uname -a Darwin 10.8.0 Darwin Kernel Version 10.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386 i386

  Read the article

• ProxyPass for specific vhost with mod_rewrite

  - by Steve Robbins

  I have a web server that it set up to dynamically server different document roots for different domains <VirtualHost *:80> <IfModule mod_rewrite.c> # Stage sites :: www.[document root].server.company.com => /home/www/[document root] RewriteCond %{HTTP_HOST} ^www\.[^.]+\.server\.company\.com$ RewriteRule ^(.+) %{HTTP_HOST}$1 [C] RewriteRule ^www\.([^.]+)\.server\.company\.com(.*) /home/www/$1/$2 [L] </IfModule> </VirtualHost> This makes it so that www.foo.server.company.com will serve the document root of server.company.com:/home/www/foo/ For one of these sites, I need to add a ProxyPass, but I only want it to be applied to that one site. I tried something like <VirtualHost *:80> <Directory /home/www/foo> UseCanonicalName Off ProxyPreserveHost On ProxyRequests Off ProxyPass /services http://www-test.foo.com/services ProxyPassReverse /services http://www-test.foo.com/services </Directory> </VirtualHost> But then I get these errors ProxyPreserveHost not allowed here ProxyPass|ProxyPassMatch can not have a path when defined in a location. How can I set up a ProxyPass for a single virtual host?

  Read the article

• How to configure IIS for SVG and web testing with Visual Studio?

  - by macias

  Let's say I have a simple web page with svg image in it: <img src="foobar.svg" alt="not working" /> If I make this page as static html page and view it directly svg is displayed. If I type the address of this svg -- it is displayed. But when I make this as .aspx page and launch it dynamically from Visual Studio I get alt text. If I type the address of this svg (from localhost, not as a local file) -- browser tries to download it instead of displaying. I already defined mime type in IIS (for entire server -- "image/svg+xml") and restarted IIS. Same effect as before. Question: what should I do more? Update WireShark won't work (it is in documentation), I tried also RawCap, but it cannot trace my connection (odd), luckily Fiddler worked: From client: GET http://127.0.0.1:1731/svg/document_edit.svg HTTP/1.1 Host: 127.0.0.1:1731 User-Agent: Mozilla/5.0 (Windows NT 6.1; rv:10.0.1) Gecko/20100101 Firefox/10.0.1 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip, deflate Connection: keep-alive Answer from server: HTTP/1.1 200 OK Server: ASP.NET Development Server/10.0.0.0 Date: Thu, 16 Feb 2012 11:14:38 GMT X-AspNet-Version: 4.0.30319 Cache-Control: private Content-Type: application/octet-stream Content-Length: 87924 Connection: Close <?xml version="1.0" encoding="UTF-8" standalone="no"?> <!-- Created with Inkscape (http://www.inkscape.org/) --> <svg xmlns: *** FIDDLER: RawDisplay truncated at 128 characters. Right-click to disable truncation. *** For the record, here is useful Q&A for Fiddler: http://stackoverflow.com/questions/826134/how-to-display-localhost-traffic-in-fiddler-while-debugging-an-asp-net-applicati

  Read the article

• What am I doing wrong in my config for MySql?

  - by Knight Hawk3

  When I load my my.conf with the config at the bottom Mysql fails to start and prints no errors. I am running Arch Linux (Updated) with the latest MySQL (5.5) and the latest nginx (Well latest in the repository, Not sure how to check. Only installed it today) I will give you any info you ask for. Thanks for helping! # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/run/mysqld/mysqld.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/run/mysqld/mysqld.sock skip-locking key_buffer = 16K max_allowed_packet = 1M table_cache = 4 sort_buffer_size = 64K read_buffer_size = 256K read_rnd_buffer_size = 256K net_buffer_length = 2K thread_stack = 64K # Don’t listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (using the “enable-named-pipe” option) will render mysqld useless! # #skip-networking server-id = 1 # Uncomment the following if you want to log updates #log-bin=mysql-bin # Uncomment the following if you are NOT using BDB tables skip-bdb # Uncomment the following if you are using InnoDB tables #innodb_data_home_dir = /var/lib/mysql/ #innodb_data_file_path = ibdata1:10M:autoextend #innodb_log_group_home_dir = /var/lib/mysql/ #innodb_log_arch_dir = /var/lib/mysql/ # You can set .._buffer_pool_size up to 50 – 80 % # of RAM but beware of setting memory usage too high #innodb_buffer_pool_size = 16M #innodb_additional_mem_pool_size = 2M # Set .._log_file_size to 25 % of buffer pool size #innodb_log_file_size = 5M #innodb_log_buffer_size = 8M #innodb_flush_log_at_trx_commit = 1 #innodb_lock_wait_timeout = 50 skip-innodb [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 1M sort_buffer_size = 1M [myisamchk] key_buffer = 1M sort_buffer_size = 1M [mysqlhotcopy] interactive-timeout So what is my silly error?

  Read the article

• Mounting a VirtualBox shared folder on boot with fstab in OpenSuse 11.3

  - by ccook

  I have followed the steps found here, however, the share is not mounted on boot. The share will mount if i run 'mount -a' after booting. Why would the share not mount on boot? 1 - Set up a Virtual Machine and install OpenSUSE 11.2 2 - Create a shared folder on host (HostFolder) 3 - Setup the shared folder in Virtualbox Via the Virtual Machine details or via Devices Shared Folders... 4 - Install dependencies for running the Virtualbox installer You need to install the right development kernelpackage for your machinetype (use 'zypper search -i kernel' to see what's installed) sudo zypper install make gcc kernel-source kernel-hosttype/default-devel 5 - Run the Virtual Machine and go to Devices Guest Additions This mounts an iso image in your OpenSUSE guest. 6 - Open a root terminal and run cd /usr/src/linux make oldconfig && make prepare && make scripts && make dep cp ../linux-obj/$HOSTTYPE/default/Module.symvers . make prepare A commenter on previously mentioned thread says this step is unnecessary but it doesn't work without on my system. I suggest trying step 7 first and returning to step 6 if that fails. * 7 - Run ./VirtualboxLinux yourhosttype .run from the mounted iso image. 8 - Create shared folder in OpenSUSE (GuestFolder) 9 - Test with sudo mount -t vboxsf HostFolder /home/user/GuestFolder It works? Great! Let's set up the system so it automounts for your regular useraccount instead of root-only access. 10 - Add this line to /etc/fstab HostFolder /home/user/GuestFolder vboxsf defaults,uid=1000,gid=1000 0 0 11 - It works for me but if it still doesn't automount after a reboot; sudo mount -a

  Read the article

• Connection refused in ssh tunnel to apache forward proxy setup

  - by arkascha

  I am trying to setup a private forward proxy in a small server. I mean to use it during a conference to tunnel my internet access through an ssh tunnel to the proxy server. So I created a virtual host inside apache-2.2 running the proxy, the proxy_http and the proxy_connect module. I use this configuration: <VirtualHost localhost:8080> ServerAdmin xxxxxxxxxxxxxxxxxxxx ServerName yyyyyyyyyyyyyyyyyyyy ErrorLog /var/log/apache2/proxy-error_log CustomLog /var/log/apache2/proxy-access_log combined <IfModule mod_proxy.c> ProxyRequests On <Proxy *> # deny access to all IP addresses except localhost Order deny,allow Deny from all Allow from 127.0.0.1 </Proxy> # The following is my preference. Your mileage may vary. ProxyVia Block ## allow SSL proxy AllowCONNECT 443 </IfModule> </VirtualHost> After restarting apache I create a tunnel from client to server: #> ssh -L8080:localhost:8080 <server address> and try to access the internet through that tunnel: #> links -http-proxy localhost:8080 http://www.linux.org I would expect to see the requested page. Instead a get a "connection refused" error. In the shell holding open the ssh tunnel I get this: channel 3: open failed: connect failed: Connection refused Anyone got an idea why this connection is refused ?

  Read the article

• Windows 2008 R2 Servers Sending Arp Requests for IPs outside Subnet

  - by Kyle Brandt

  By running a packet capture on my my routers I see some of my servers sending ARP requests for IPs that exist outside of its network. For example if my network is: Network: 8.8.8.0/24 Gateway: 8.8.8.1 (MAC: 00:21:9b:aa:aa:aa) Example Server: 8.8.8.20 (MAC: 00:21:9b:bb:bb:bb) By running a capture on the interface that has 8.8.8.1 I see requests like: Sender Mac: 00:21:9b:bb:bb:bb Sender IP: 8.8.8.20 Target MAC: 00:21:9b:aa:aa:aa Target IP: 69.63.181.58 Anyone seen this behavior before? My understanding of ARP is that requests should only go out for IPs within the subnet... Am I confused in my understanding of ARP? If I am not confused, anyone seen this behavior? Also, these seem to happen in bursts and it doesn't happen when I do something like ping an IP outside of the network. Update: In response to Ian's questions. I am not running anything like Hyper-V. I have multiple interfaces but only one is active (Using BACS failover teaming). The subnet mask is 255.255.255.0 (Even if it were something different it wouldn't explain an IP like 69.63.181.58). When I run MS Network Monitor or wireshark I do not see these ARP requests. What happens is that on the router capturing I see a burst of about 10 requests for IPs outside of the network from the host machine. On the machine itself using wireshark or NetMon I see a flood of ARP responses for all the machines on the network. However, I don't see any requests in the capture asking for those responses. So it seems like maybe it is maybe refreshing the arp cache but including IPs that outside of the network. Also when it does this NetMon doesn't show the ARP requests?

  Read the article

• File Sync Solution for Batch Processing (ETL)

  - by KenFar

  I'm looking for a slightly different kind of sync utility - not one designed to keep two directories identical, but rather one intended to keep files flowing from one host to another. The context is a data warehouse that currently has a custom-developed solution that moves 10,000 files a day, some of which are 1+ gbytes gzipped files, between linux servers via ssh. Files are produced by the extract process, then moved to the transform server where a transform daemon is waiting to pick them up. The same process happens between transform & load. Once the files are moved they are typically archived on the source for a week, and the downstream process likewise moves them to temp then archive as it consumes them. So, my requirements & desires: It is never used to refresh updated files - only used to deliver new files. Because it's delivering files to downstream processes - it needs to rename the file once done so that a partial file doesn't get picked up. In order to simplify recovery, it should keep a copy of the source files - but rename them or move them to another directory. If the transfer fails (network down, file system full, permissions, file locked, etc), then it should retry periodically - and never fail in a non-recoverable way, or a way that sends the file twice or never sends the file. Should be able to copy files to 2+ destinations. Should have a consolidated log so that it's easy to find problems Should have an optional checksum feature Any recommendations? Can Unison do this well?

  Read the article

• Courier IMAP always disconnects since update

  - by Raffael Luthiger

  Since one of our customers updated their server courier does not handle IMAP connections properly any more. POP3 works without any problems. When I try to test IMAP with telnet then it is always like this: $ telnet domain.com 143 Trying 188.40.46.214... Connected to domain.com. Escape character is '^]'. * OK [CAPABILITY IMAP4rev1 UIDPLUS CHILDREN NAMESPACE THREAD=ORDEREDSUBJECT THREAD=REFERENCES SORT QUOTA IDLE ACL ACL2=UNION STARTTLS] Courier-IMAP ready. Copyright 1998-2011 Double Precision, Inc. See COPYING for distribution information. 01 LOGIN [email protected] test Connection closed by foreign host. I enabled debugging in the authdaemond but the output does not really help much: Apr 12 23:10:04 servername authdaemond: received auth request, service=imap, authtype=login Apr 12 23:10:04 servername authdaemond: authmysql: trying this module Apr 12 23:10:04 servername authdaemond: SQL query: SELECT login, password, "", uid, gid, homedir, maildir, quota, "", concat('disableimap=',disableimap,',disablepop3=',disablepop3) FROM mail_user WHERE login = '[email protected]' Apr 12 23:10:04 servername authdaemond: password matches successfully Apr 12 23:10:04 servername authdaemond: authmysql: sysusername=<null>, sysuserid=5000, sysgroupid=5000, homedir=/var/vmail, [email protected], fullname=<null>, maildir=/var/vmail/domain.com/test, quota=0, options=disableimap=n,disablepop3=n Apr 12 23:10:04 servername authdaemond: Authenticated: sysusername=<null>, sysuserid=5000, sysgroupid=5000, homedir=/var/vmail, [email protected], fullname=<null>, maildir=/var/vmail/domain.com/test, quota=0, options=disableimap=n,disablepop3=n Right after the "Authenticated" line the output stops. There is no other message. And in no other log file I've checked I could find any other related message. The system was updated from Ubuntu 10.10 to 12.04. How could I get more information? Or does anybody have an idea what could go wrong here?

  Read the article

• Possible DNS Injection and/or SSL hijack?

  - by Anthony

  So if I go to my site without indicating the protocol, I'm taken to: http://example.org/test.php But if I go directly to: https://example.org/test.php I get a 404 back. If I go to just: https://example.org I get a totally different site (a page about martial arts). I went to the site via https not very long ago (maybe a week?) and it was fine. This is a shared server, as I understand it, and I do not have shell access, so I'm limited to the site's CPanel to do any further investigations. But when I go to: example.org:2083 I'm taken to https://example.org:2083, which, if someone has taken over the SSL port, could mean they have taken over the 2083 part as well (at least in my paranoid mind). I'm made more nervous by the fact that the cpanel login page at the above address looks very new (better, really) compared to the last time I went to it over the weekend. It's possible that wires got crossed somewhere after a system update, but I don't want to put in my name username and password in case it's a phishing attempt. Is there any way to know for sure without shell access to know for sure if someone has taken over? If I look up the IP address for the host name, the IP address matches what I have on a phpinfo page I can get to over http. If I go to the IP address directly on port 2083, I get the same login mentioned above (new and and suspiciously nice). But the SSL cert shows as good when I go this route. So if that's the case (I know the IP is right, the cert checks out, and there isn't any DNS involved), is that enough to feel safe at that point of entry? Finally, if I can safely log in via the IP, does anyone have any advice on where to check first on CPanel for why the SSL port is forwarding to a site on karate? Thanks.

  Read the article

• Configuring DNS and IIS for multiple domains on a single server

  - by RichardS

  I might be over complicating this but...I am hosting several websites and dns for the domains on a single server: domain1.net domain1.com domain2.net I have three items which I'm trying to work out whether to achieve by DNS, by IIS hostnames(bindings), or by IIS redirect. 1. Where I have domain1.net and domain1.com, I want everything from both (all emails and web requests) to just point to the domain1.net. Can I do this at the DNS level, or do I have to set up the email as forwarders on the email server and the domain as a hostname in IIS? For example: [email protected] [email protected] www.domain1.com www.domain1.net 2. I want to make sure that requests for domain1.net and www.domain1.net both resolve to the same place. Should this be done with DNS or with multiple hostnames, or with IIS redirects? 3. If I then want to have one webmail site serving all of domains (webmail.domain1.net, webmail.domain2.net), is it best to this with a cname in DNS or with host headers in IIS?

  Read the article

• DAS vs SAN storage for serving 2 to 4 nodes

  - by Luke404

  We currently have 4 Linux nodes with local storage, arranged in two active/passive pairs with storage mirrored using DRBD, running virtual machines (actually using Xen Hypervisor) for typical hosting workloads (mail, web, a couple VPS, etc.). We're approaching the (presumed) maximum IOPS of those servers, and we're planning to migrate to an external storage solution with two active nodes, with capacity for up to four active nodes. Since we're an all-Dell shop I've done some research and found the MD3200 / MD3200i products should be the ones we're looking for. We are pretty sure we won't be attaching more than 4 hosts on a single storage and I'm wondering if there is any clear advantage for one or the other. In theory I should be able to attach 4 SAS hosts to a single MD3200 (single links on a single controller MD3200, or dual redundant SAS links from each host to a dual-controller MD3200), or 4 iSCSI hosts to a single MD3200i (directly on its 4 GigE ports without any switch, again with dual links for the dual controller option). Both setups should let us implement live VM migration since all hosts can access all the LUNs at the same time, and also some shared filesystem like GFS2 or OCFS2. Also, both setups should allow full redundancy of the whole system (assuming dual controllers in the storage). One difference I can see is that the DAS solution is actually limited to 4 hosts while the iSCSI one should be able to grow to more hosts (adding two GigE switches to the mix). One point for the iSCSI solution is that it would allow us to start out with our current nodes and upgrade them at a later time (we can't add other SAS controllers, but they already have 4 GigE ports each). With the right (iSCSI|SAS) controllers I should be able to connect diskless nodes and boot them off the external storage which I think is a good thing (get rid of any local storage). On the other hand, I would have thought the SAS one to be cheaper but it seems like an MD3200 actually costs a little less than an MD3200i (?) (please note: I've used Dell gear in my examples since that's what we're looking for but I assume the same goes with other vendors) I would like to know if my assumptions above are correct, and if I'm missing any important difference between the two setups.

  Read the article

< Previous Page | 402 403 404 405 406 407 408 409 410 411 412 413  | Next Page >