Search Results

Search found 41598 results on 1664 pages for 'segmentation fault'.

Page 407/1664 | < Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >

• Survey of project-administration experience [on hold]

  - by Salvador Beltrán

  My name is Salvador, I'm a Computer System Eng. Student and I'm searching for people to contribute with my research and I need real opinions - Experience (is an investigation for problems in the Project Management Area), just to be clear it can be any kind of project. If you help me with these 3 questions I would appreciate you so much! :) 1 - Any kind of problem that ocurred during the process of the project administration(Just the description). 2 - What was the impact? 3 - And what was the solution to avoid this problem in some future. 4 - What do you do(Software Engineering,Networking,etc). Thank you very much!

  Read the article

• Windows 2003 DNS updates from ISC DHCP server

  - by wolfgangsz

  We have a very mixed network, with most clients being Debian Lenny, the rest Windows XP/Vista/7. The network itself is split into two segments (for technical reasons) called "corporate" and "engineering". On the "corporate" side all clients get their IP addresses from a Windows DHCP server and the dynamic updates into the Windows DNS work just fine. On the "engineering" side, clients get their IP addresses from a linux machine running the standard ISC DHCP server. Although this server is configured to do dynamic DNS updates, they actually don't work. Anybody got any advice on how to fix this? Please note: dynamic updates from the clients directly into the DNS would work, but are not an option for us. So this is strictly on how make this work from an ISC DHCP server to a Windows DNS server.

  Read the article

• Netdom to restore machine secret

  - by icelava

  I have a number of virtual machines that have not been switched on for over a month, and some others which have been rolled back to an older state. They are members of a domain, and have expired their machine secrets; thus unable to authenticate with the domain any longer. Event Type: Warning Event Source: LSASRV Event Category: SPNEGO (Negotiator) Event ID: 40960 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: The Security System detected an authentication error for the server ldap/iceland.icelava.home. The failure code from authentication protocol Kerberos was "The attempted logon is invalid. This is either due to a bad username or authentication information. (0xc000006d)". For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c000006d Event Type: Warning Event Source: LSASRV Event Category: SPNEGO (Negotiator) Event ID: 40960 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: The Security System detected an authentication error for the server cifs/iceland.icelava.home. The failure code from authentication protocol Kerberos was "The attempted logon is invalid. This is either due to a bad username or authentication information. (0xc000006d)". For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c000006d Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 3210 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: This computer could not authenticate with \\iceland.icelava.home, a Windows domain controller for domain ICELAVA, and therefore this computer might deny logon requests. This inability to authenticate might be caused by another computer on the same network using the same name or the password for this computer account is not recognized. If this message appears again, contact your system administrator. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c0000022 So I try to use netdom to re-register the machine back to the domain C:\Documents and Settings\Administrator>netdom reset tfs2008wdata /domain:icelava /UserO:enterpriseadmin /PasswordO:mypassword Logon Failure: The target account name is incorrect. The command failed to complete successfully. But have not been successful. I wonder what else needs to be done?

  Read the article

• sshd warning, "POSSIBLE BREAK-IN ATTEMPT!" for failed reverse DNS

  - by rking

  Whenever I SSH somewhere I get something like this in the logs: sshd[16734]: reverse mapping checking getaddrinfo for 1.2.3.4.crummyisp.net [1.2.3.4] failed - POSSIBLE BREAK-IN ATTEMPT! And it is right: if I do host 1.2.3.4 it returns 1.2.3.4.crummyisp.net, but if I do host 1.2.3.4.crummyisp.net it is not found. I have two questions: What security threat is there? How could anyone fake a one-way DNS in some threatening way? Do I have any recourse for fixing this? I'll send my ISP a bug report, but who knows where that'll go.

  Read the article

• What is the difference between "su --command" and "su --session-command"?

  - by oliver

  Running # su - oliver --command bash gives a shell but also prints the warning bash: no job control in this shell, and indeed Ctrl+Z and fg/bg don't work in that shell. Running # su - oliver --session-command bash gives a shell without printing the warning, and job control indeed works. The suggestion to use --session-command comes from Starting a shell from scripts using su results in "no job control in this shell" which states "[a security fix for su] changed the behavior of the -c option and disables job control inside the called shell". But I still don't quite understand this. When should one use --command and when should one use --session-command? Is --command (aka -c) more secure? Or should one always use --session-command, and --command is just left in for backwards compatibility? FWIW, I'm using RHEL 6.4.

  Read the article

• Need a Company to Fix My Plesk & IIS on windows 2008 [SOLVED]

  - by DevCompany

  Hello: I need to know a name of a company to fix my server install and get my sites running again. Windows 2008 IIS 7 Plesk 9.x The problem started when Level 2 of my hosting company adjusted a FTP users to have certain permissions....apparently he did this outside of plesk and it has been nothing but permission headaches all around. Connections....uploading files, etc. now somethings gone wrong where plesk isnt even loading properly and IIS too... I need to see if someone can fix this remotely before I give the green light to format and reinstall server, IIS, Plesk and Domains! looking to pay a company to get this working ASAP - This is not requested as a free job so I need someone good and who can fix it without the huge hassle of formatting and such. Need to resolve today Post expires on Monday 04-26-20010

  Read the article

• does vmware server needs bare metal or can be installed on an existing OS

  - by Registered User

  I am new to virtual stuff on Vmware sort of environment.I am basically testing Vmware and its various things for our needs.I have a linux 64 bit laptop.I want to know 1) The Vmware server can it be installed in this existing OS or I need to have baremetal installation for this? 2) What is the advantage of using Vmware Server on Vmware workstation ? 3) What is the use of ESX server of vmware? I have seen some alternatives like Xen which one is better Xen or Vmware might be a debatable issue but my questions for Xen are also same I checked Citrix website. 1) I see similar products for Xen What is the advantage of using Xen Server on Xen desktop ?

  Read the article

• Access Denied Error in PagesListCPVEventReceiver post SharePoint SP2 upgrade

  - by JD

  I am seeing the following errors from one of the SharePoint Web Front Ends after the SP2 upgrade. Has anyone else seen this error or a solution? Event Type: Error Event Source: Windows SharePoint Services 3 Event Category: General Event ID: 6875 Date: 2009-10-27 Time: 13:09:57 User: N/A Computer: XXXXXXX Description: Error loading and running event receiver Microsoft.SharePoint.Publishing.PagesListCPVEventReceiver in Microsoft.SharePoint.Publishing, Version=12.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429c. Additional information is below. : Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED)) For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Add unallocated space to lvm

  - by Newbie

  I shrunk my windows partition and now have 10 GB of unallocated space that I now want to use to grow my / partition which is an ext4 in an lvm. I'm running Fedora 12. I ran system-config-lvm but the "Initialize Entry" button is greyed out. The unallocated space is not adjacent to the lvm but I cannot move the partitions in GParted like I was able to with ext3 in the past. I cannot create a new partition either as it says it cannot have more than 4 primary partitions. I don't see any option to create an extended partition. So my question is, how do I add that unallocated space to the lvm so I can grow the size of the / partition? I don't want to reinstall Fedora.

  Read the article

• Windows 7 Multi Monitor RDC Problem [closed]

  - by Peter Stegnar

  Possible Duplicate: Windows remote controle for dual monitor setup I would like to use all my monitors for the remote session (an option in RDC dialogue) if I connect (from Windows 7) to the one server with Windows 2008 R2 it works OK (I have remote connection on my all monitors) when do I connect to the another server with Windows 7 it just wound not use all my monitors, but just one (full screen mode). What do I missing here? Some setting on the Windows 7 server? Basically my question is: How to establish multimonitor RDC connection from Windows 7 to another Windows 7 running computer?

  Read the article

• rdiff-backup command to restore

  - by Hulk

  Let say i have a source directory which contains The contents /foo/a /foo/b(These are the files in a directory on a remote system) using rdiff command i make a backup as rdiff-backup [email protected]::/foo backups And a,b are now present in my backups directory.And then i delete file a from the remote system and again i do a sync so my local directory has the file b only. My question is that how do i restore file a if the deletion and sync is done on the same day Thanks..

  Read the article

• CentOS 6 - Make system aware of custom lib paths and missing base links

  - by Mike Purcell

  I am trying to compile libmemcached (1.0.7) on CentOS6, and keep getting the following warning: ... checking for event.h... no configure: WARNING: Unable to find libevent ... I manually compiled libevent (2.0.19) and built it using the following configure line: OPTIONS="--prefix=/usr/local/_custom/app/libevent" Everything compiled and installed fine, but I couldn't figure out how to make the system aware that the lib files are in the custom /usr/local/_custom/app/libevent/libdir. I stumbled upon an article and read that I can make the system aware of custom lib paths by adding a custom file to /etc/ld.so.conf.d/ directory: # /etc/ld.so.conf.d/customApp.conf /usr/local/_custom/app/libevent/lib Then I issued the ldconfig command and was able to confirm that libevent was included by issuing this command: ldconfig -p | ack -i libevent Seeing that libevent was now included in the ldconfig output, I figured I would be able to compile libmemcached and satisfy the aforementioned warning. Unfortunately it did not. So I took another look at the ldconfig output and noticed this: libevent_pthreads-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_pthreads-2.0.so.5 libevent_openssl-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_openssl-2.0.so.5 libevent_extra-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_extra-2.0.so.5 libevent_core-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_core-2.0.so.5 libevent-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent-2.0.so.5 There are no references to the base links, for example, I would expect to see links to these (ls -la /usr/local/_custom/app/libevent/lib): libevent.so -> libevent-2.0.so.5.1.7 libevent_openssl.so -> libevent_openssl-2.0.so.5.1.7 libevent_core.so -> libevent_core-2.0.so.5.1.7 So either I am doing something wrong, or the system still does not know where to look to find libevent.so. -- Update #1 -- I wasn't able to get libmemcached to compile without the warning notice, even after trying to compile using the following configure command: ./configure --prefix=/usr/local/_custom/app/libmemcached CFLAGS="-I/usr/local/_custom/app/libevent/include" LDFLAGS="-L/usr/local/_custom/app/libevent/lib" I thought for sure this would work because I am directly passing the include and lib directories to the configure command. But it did not.

  Read the article

• How to install subversion on 1&1 server with windows?

  - by Miles M.

  I would like to start using Unfuddle for my project on 1&1 server. I never used subversion and core control before. So, I read a lot of documentation about it but each time, I get lost at the very beginning : I've downloaded the latest version of subversion. But on every tutorial, the way to follow is different. First I sae, on a lot of tuts, that you have to enter command lines. Is that ONLY for Linux ? Like here : http://chwalisz.org/2007/08/05/subversion-on-11-shared-hosting/ I also find something completely different on some website, I think (correct me if I'm wrong) it is the Windows tuts, deeply different frm the linu one. So I found that : http://www.codinghorror.com/blog/2008/04/setting-up-subversion-on-windows.html http://geekswithblogs.net/emanish/archive/2006/06/14/81905.aspx http://better-scm.shlomifish.org/subversion/Svn-Win32-Inst-Guide.html And I don t understand : Do I still have to put the sibversion file on the server ? Do I have to install Apach ? where, on my computer or on my server ? I'm working ith WampServer so I thing I have already Apach installed right ? When they say it is for Windows, do they mean it is for windows servers or for your own OS ? 'Cause my servers are on linux. How could I install Subversion on a 1&1 linux server from my W7 OS computer ? Thanks, that's a lot of question but that realle messy in my mind, I can't find something clear ..

  Read the article

• Reverse proxy setup for distributed storage

  - by vise

  I have 4 file servers that I want to access under a single mount point from another server. This server has a web application that should serve content from the mounted point. I think I can achieve this with glusterfs. Considering that the file servers have fairly powerful hardware, I want to install a webserver on each of them and serve those files via a reverse proxy. Any thoughts on how I may be able to do so?

  Read the article

• Issue in setting up VPN connection (IKEv1) using android (ICS vpn client) with Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using android (ICS vpn client) and Strongswan 4.5.0 server. Below is the set up: Strongswan server is running on ubuntu linux machine which is connected to some wifi hotspot. Using the steps in this guide link, I generated CA, server and client certificate. Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on android device. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212, android device eth0 interface ip address: 192.168.43.62; Android device is also attached with the same wifi hotspot. On the Android device, I uses IPsec Xauth RSA option for setting up VPN authentication configuration. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.62 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add      With the above configurations when I enable VPN on android device, VPN connection is not successful and it gets timed out in Authentication phase. I ran wireshark on both the android device and strongswan server, from the tcpdump below are the observations. Initially Identity Protection (Main mode) exchanges happens between device and server and all are successful. After all successful Identity Protection (Main mode) exchanges server is sending Transaction (Config mode) to device. In reply android device is sending Informational message instead of Transaction (Config mode) message. Further server is keep on sending Transaction (Config mode) message and device is again sending Identity Protection (Main mode) messages. Finally timeout happens and connection fails. I also capture Strongswan server logs and below are the snippets from the server logs which also verifies the same(described above). Apr 27 21:09:40 Linux pluto[12105]: | **parse ISAKMP Message: Apr 27 21:09:40 Linux pluto[12105]: | initiator cookie: Apr 27 21:09:40 Linux pluto[12105]: | 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | responder cookie: Apr 27 21:09:40 Linux pluto[12105]: | 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | next payload type: ISAKMP_NEXT_HASH Apr 27 21:09:40 Linux pluto[12105]: | ISAKMP version: ISAKMP Version 1.0 Apr 27 21:09:40 Linux pluto[12105]: | exchange type: ISAKMP_XCHG_INFO Apr 27 21:09:40 Linux pluto[12105]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 27 21:09:40 Linux pluto[12105]: | message ID: a2 80 ad 82 Apr 27 21:09:40 Linux pluto[12105]: | length: 92 Apr 27 21:09:40 Linux pluto[12105]: | ICOOKIE: 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | RCOOKIE: 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | peer: c0 a8 2b 3e Apr 27 21:09:40 Linux pluto[12105]: | state hash entry 25 Apr 27 21:09:40 Linux pluto[12105]: | state object not found Apr 27 21:09:40 Linux pluto[12105]: packet from 192.168.43.62:500: Informational Exchange is for an unknown (expired?) SA Apr 27 21:09:40 Linux pluto[12105]: | next event EVENT_RETRANSMIT in 10 seconds for #9 Can anyone please provide update on this issue. Why the VPN connection gets timed out and why the ISAKMP exchanges are not proper between Android and strongswan server.

  Read the article

• Unable to start auditd

  - by George Reith

  I am on CentOS 5.8 final I recently installed auditd via yum install audit however I am unable to start it. I edited the configuration file to give a verbose output of the error it is recieving in starting up and this is the output: # service auditd start Starting auditd: Config file /etc/audit/auditd.conf opened for parsing log_file_parser called with: /var/log/audit/audit.log log_format_parser called with: RAW log_group_parser called with: root priority_boost_parser called with: 4 flush_parser called with: INCREMENTAL freq_parser called with: 20 num_logs_parser called with: 4 qos_parser called with: lossy dispatch_parser called with: /sbin/audispd name_format_parser called with: NONE max_log_size_parser called with: 5 max_log_size_action_parser called with: ROTATE space_left_parser called with: 75 space_action_parser called with: SYSLOG action_mail_acct_parser called with: root admin_space_left_parser called with: 50 admin_space_left_action_parser called with: SUSPEND disk_full_action_parser called with: SUSPEND disk_error_action_parser called with: SUSPEND tcp_listen_queue_parser called with: 5 tcp_max_per_addr_parser called with: 1 tcp_client_max_idle_parser called with: 0 enable_krb5_parser called with: no GSSAPI support is not enabled, ignoring value at line 30 krb5_principal_parser called with: auditd GSSAPI support is not enabled, ignoring value at line 31 Started dispatcher: /sbin/audispd pid: 3097 type=DAEMON_START msg=audit(1339336882.187:9205): auditd start, ver=1.8 format=raw kernel=2.6.32-042stab056.8 auid=4294967295 pid=3095 res=success config_manager init complete Error setting audit daemon pid (Connection refused) type=DAEMON_ABORT msg=audit(1339336882.189:9206): auditd error halt, auid=4294967295 pid=3095 res=failed Unable to set audit pid, exiting The audit daemon is exiting. Error setting audit daemon pid (Connection refused) [FAILED] The only information I can find online is that this may be due to SELinux, however SELinux is giving me problems of it's own. No matter what I do it appears to be disabled (I want to enable it). The configuration is set to enforced and the server has been rebooted many a time however sestatus still returns SELinux status: disabled. Can anyone shine some light on this problem? EDIT: I don't know if it is related but I noticed the following message appearing in my /var/log/messages Jun 10 16:25:22 s1 iscsid: iSCSI logger with pid=2056 started! Jun 10 16:25:22 s1 iscsid: Missing or Invalid version from /sys/module/scsi_transport_iscsi/version. Make sure a up to date scsi_transport_iscsi module is loaded and a up todate version of iscsid is running. Exiting... I try to start the iSCSI daemon myself (I have not a clue what it does; I am a linux newbie) and I get the following error: Starting iSCSI daemon: FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.32-042stab056.8/modules.dep: No such file or directory [FAILED] If I go to /lib/modules/ I notice the directory exists but is completely empty.

  Read the article

• How to solve SocketException: Permission denied: connect

  - by luxinxian

  I recently encountered a problem that is giving me a headache and I need help ... The System consists of two subsystems, called A and B, each running on a standalone Tomcat instance and currently running on the same machine. A invokes B's service via Spring httpInvoker (i.e. over HTTP). B system also invokes the other system's services via HTTP. Symptoms: the system starts to run and appears to work normally for around 10-15 days; the system will run for a period of time after an exception: org.springframework.remoting.RemoteAccessException: Could not access HTTP invoker remote service at [http://xxx.xxx.xxx.xxx/remoting/call]; The nested exception is java. net.SocketException: **Permission denied: connect** when the exception occurs, the system continues. This happens always, not only occasionally. (It looks like some resources are exhausted, but CPU rate < 5%, memory < 15%, network < 5%). when the system call between A and B fails, the B system call over HTTP to an external service also failed, with the same exception. Restarting both Tomcat services makes the whole system work properly. So repeatedly following steps 1 - 5, I have not found the root reason. Environment: windows 2008 R2 tomcat7.0.42 x86_64 oralce-jdk-1.7.0_40 Any ideas?

  Read the article

• 4096 and 8192 block size read slower than write? by using lsi 9361-8i RAID10

  - by Min Hong Tan

  is it possible that 1024 and 2048 block size read speed is faster than 4096 and 8192 block? I'm using lsi 9361-8i with RAID 10 , with 8 x Kingston E50 250G. result: 1024 = Write: 2,251 MB/s Read: 2,625 MB/s 2048 = Write: 2,141 MB/s Read: 3,672 MB/s 4096 = Write: 2,147 MB/s Read: 231 MB/s 8192 = Write: 2,147 MB/s Read: 442 MB/s is there any possible? and below is the reading when i simply want to test out the RAID 10 function and disaster test by taking out one of the 250G harddisk. the result is different like below: Result: 1024 = Write: 825 MB/s Read: 1,139 MB/s 2048 = Write: 797 MB/s Read: 1,312 MB/s 4096 = Write: 911 MB/s Read: 1,342 MB/s 8192 = Write: 786 MB/s Read: 1,204 MB/s and the result for 4096 and 8192block are different? can any one explain to me is it normal? or I need to do some tuning/configuration? will it affect my host linux performance?

  Read the article

• how do i write an init script for django-supervisor

  - by amateur

  pardon me as this is my first time attempting to write a init script for centos 5. I am using django + supervisor to manage my celery workers, scheduler. Now, this is my naive simple attempt /etc/init.d/supervisor #!/bin/sh # # /etc/rc.d/init.d/supervisord # # Supervisor is a client/server system that # allows its users to monitor and control a # number of processes on UNIX-like operating # systems. # # chkconfig: - 64 36 # description: Supervisor Server # processname: supervisord # Source init functions /home/foo/virtualenv/property_env/bin/python /home/foo/bar/manage.py supervisor --daemonize inside my supervisor.conf: [program:celerybeat] command=/home/property/virtualenv/property_env/bin/python manage.py celerybeat --loglevel=INFO --logfile=/home/property/property_buyer/logfiles/celerybeat.log [program:celeryd] command=/home/foo/virtualenv/property_env/bin/python manage.py celeryd --loglevel=DEBUG --logfile=/home/foo/bar/logfiles/celeryd.log --concurrency=1 -E [program:celerycam] command=/home/foo/virtualenv/property_env/bin/python manage.py celerycam I couldn't get it to work. 2013-08-06 00:21:03,108 INFO exited: celerybeat (exit status 2; not expected) 2013-08-06 00:21:06,114 INFO spawned: 'celeryd' with pid 11772 2013-08-06 00:21:06,116 INFO spawned: 'celerycam' with pid 11773 2013-08-06 00:21:06,119 INFO spawned: 'celerybeat' with pid 11774 2013-08-06 00:21:06,146 INFO exited: celerycam (exit status 2; not expected) 2013-08-06 00:21:06,147 INFO gave up: celerycam entered FATAL state, too many start retries too quickly 2013-08-06 00:21:06,147 INFO exited: celeryd (exit status 2; not expected) 2013-08-06 00:21:06,152 INFO gave up: celeryd entered FATAL state, too many start retries too quickly 2013-08-06 00:21:06,152 INFO exited: celerybeat (exit status 2; not expected) 2013-08-06 00:21:07,153 INFO gave up: celerybeat entered FATAL state, too many start retries too quickly I believe it is the init script, but please help me understand what is wrong.

  Read the article

• ext4 filesystem corruption -- maybe hardware error?

  - by pts

  I'm getting these errors in dmesg after about half an hour after I turn on the computer: [ 1355.677957] EXT4-fs error (device sda2): htree_dirblock_to_tree: inode #1318420: (comm updatedb.mlocat) bad entry in directory: directory entry across blocks - block=5251700offset=0(0), inode=1802725748, rec_len=179136, name_len=32 [ 1355.677973] Aborting journal on device sda2-8. [ 1355.678101] EXT4-fs (sda2): Remounting filesystem read-only [ 1355.690144] EXT4-fs error (device sda2): htree_dirblock_to_tree: inode #1318416: (comm updatedb.mlocat) bad entry in directory: directory entry across blocks - block=5251699offset=0(0), inode=2194783952, rec_len=53280, name_len=152 [ 1356.864720] EXT4-fs error (device sda2): htree_dirblock_to_tree: inode #1312795: (comm updatedb.mlocat) bad entry in directory: directory entry across blocks - block=5251176offset=1460(13748), inode=1432317541, rec_len=208208, name_len=119 /dev/sda is an SSD, and it's using the noop scheduler. /etc/fstab entry: UUID=acb4eefa-48ff-4ee1-bb5f-2dccce7d011f / ext4 errors=remount-ro,noatime,discard,user_xattr 0 1 System information: $ cat /proc/mounts | grep /dev/sd /dev/sda1 /boot ext2 rw,noatime,errors=continue 0 0 $ cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=10.04 DISTRIB_CODENAME=lucid DISTRIB_DESCRIPTION="Ubuntu 10.04.3 LTS" $ uname -a Linux leetpad 2.6.35-30-generic-pae #61~lucid1-Ubuntu SMP Thu Oct 13 21:14:29 UTC 2011 i686 GNU/Linux I've run memtest for 7 hours, it didn't found any memory errors. Any obvious ideas what can go wrong in this case? The most reasonable thing I can imagine is that the SSD is silently dropping some write requests, which eventually leads to an EXT4 filesystem inconsistency (but no disk I/O errors). How can this happen? Is there a relevant configuration option I should ensure to be set correctly? What tools should I use to diagnose the hardware failures? Would it be possible to diagnose the SSD failure without overwriting data?

  Read the article

• How to enter into BusyBox when booting?

  - by ???

  I have occasionally installed cloud-init package in Ubuntu, which blocks me from booting. Neither recovery mode works. Because cloud-init installed some upstart job configuration. So I want to enter into busybox to remove /etc/init/cloud-init*.conf, but it seems like no way to do it. I can press Ctrl+Alt+SysRq which brings on a rough hack menu, but there is no busybox option. So is it possible? My CDROM is broken so I can't use Live CD too.

  Read the article

• MAC computer is not seeing the Ubuntu(computer) samba share in SHare

  - by Mirage

  I have ubuntu with samba installed. Initially My Windows were not able to see Ubuntu on my network list. After searchinga lot i found that i had to write this line in smb.conf and it worked "ldap ssl = No" Don't know why. Now my MAC is also not able to see ubunut but if click on connect to server and use smb://servername then my connection is established. Now is there any thing which i can do so that MAC can see ubuntu in share and i don't need to use connect to server thing.

  Read the article

• Free login on Windows Seven

  - by Rafael

  I have a delphi procedure to validate the user login on my system integrated with Active Directory. On Windows xP/2000 when the user use a invalid password It's OK, but on Windows seven the procedure didn't validating the username and password, then the user has a free access on the system

  Read the article

• Read only bind-mount?

  - by depesz

  I use mount -o bind to mount directories inside chroots, which works really well. The problem is that I'd like some of these bind-mounted directories to be read only in chroot. Is it possible? If not - any other way to achieve it? I was thinking about using NFS for localhost mounts, but it looks like overkill.

  Read the article

• Does servers to >$1000 really have a memory limit of 4GB?

  - by Sandra

  Hi, I am looking for a server, and when I look at the specs some of the servers can only handle 4GB. Other can handle 8GB or 16GB, and others 64GB. Can that really be true? Is this really a hardware limitation, or are they disabling it in the BIOS, so there is no way to use 16GB on a 4GB supported server? An example is the Dell PowerEdge SC 440. Only 4GB supported, they say. Would Linux allow me to use 16GB on a 4GB server? Sandra

  Read the article

< Previous Page | 403 404 405 406 407 408 409 410 411 412 413 414  | Next Page >