Search Results

Search found 27932 results on 1118 pages for 'finite state machine'.

Page 409/1118 | < Previous Page | 405 406 407 408 409 410 411 412 413 414 415 416  | Next Page >

• Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

  - by Pro Backup

  In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

  Read the article

• Can builds be hidden or stepped through in Apple´s Keynote editor so they don't obstruct other objec

  - by meeeee

  I'm new to keynote and as such have not figured out the correct workflow yet. While the transitions (builds) and actions are nice, how are you supposed to work with several objects if the previously edited objects are still being displayed in the original state, thus obstructing the view on new elements that I would like to display later? Is there a way to step through the builds like in presentation mode?

  Read the article

• WS2008 subst in Logon script does not "stick"

  - by Frans

  I have a terminal server environment exclusively with Windows Server 2008. My problem is that I need to "map" a drive letter to each users Temp folder. This is due to a legacy app that requries a separate Temp folder for each user but which does not understand %temp%. So, just add "subst t: %temp%" to the logon script, right? The problem is that, even though the command runs, the subst doesn't "stick" and the user doesn't get a T: drive. Here is what I have tried; The simplest version: 'Mapping a temp drive Set WinShell = WScript.CreateObject("WScript.Shell") WinShell.Run "subst T: %temp%", 2, True That didn't work, so tried this for more debug information: 'Mapping a temp drive Set WinShell = WScript.CreateObject("WScript.Shell") Set procEnv = WinShell.Environment("Process") wscript.echo(procEnv("TEMP")) tempDir = procEnv("TEMP") WinShell.Run "subst T: " & tempDir, 3, True This shows me the correct temp path when the user logs in - but still no T: Drive. Decided to resort to brute force and put this in my login script: 'Mapping a temp drive Set WinShell = WScript.CreateObject("WScript.Shell") WinShell.Run "\\domain\sysvol\esl.hosted\scripts\tempdir.cmd", 3, True where \domain\sysvol\esl.hosted\scripts\tempdir.cmd has this content: echo on subst t: %temp% pause When I log in with the above then the command window opens up and I can see the subst command being executed correctly, with the correct path. But still no T: drive. I have tried running all of the above scripts outside of a login script and they always work perfectly - this problem only occurs when doing it from inside a login script. I found a passing reference on an MSFN forum about a similar problem when the user is already logged on to another machine - but I have this problem even without being logged on to another machine. Any suggestion on how to overcome this will be much appreciated.

  Read the article

• How to figure out what VirtualBox did?

  - by AndrejaKo

  I'm trying to boot a custom made-in-ASM OS on my recent laptop. The OS is intended to be installed on a floppy and during make creates a bootable floppy. Since I don't have a floppy drive, I installed it on a virtual floppy. After that I used WinToFlash's create bootable MS-DOS USB drive option to transfer the floppy image to an USB flash drive. Then I tried to boot my computer from it but got only a repeating broken string on screen. After all that I made a virtual hard disk image form the flash drive using this tutorial and tried to boot a virtual machine from it. First time I got same problem as on real computer. I then used the reset option and next time and every time after that OS booted correctly. My question is: How do I figure out what exactly happened to the virtual machine between first and second boot? UPDATE I just created a new VM with default settings for windows XP and it has the same problem that I have on a real computer. I was unable to reproduce the procedure which made the first VM work correctly.

  Read the article

• Windows: How to make programs think they're not running in a terminal server session?

  - by sinni800

  I am using the program "SoftXPand 2011 Duo" by Miniframe on my Windows 7 PC. It makes two workstations out of one computer. It uses the terminal services built into Windows to create the additional session. I use two screens, two keyboards and two mice to create this "illusion" of two computers. It works quite well and I can even play two different 3D games on the two screens attached to this single machine (using a Radeon HD5770 and a Core i5 2500k with 8 Gbytes RAM). There are a few downsides to this. I just found about one that is hidden on the first look. The sessions you are in (even on the first workstation) will identify as a terminal server session! Now some programs will run with limited effects (graphical), and some won't run at all. This also resulted in some games not running at all. They just say "Cannot be run in a terminal server session" and exit. I have already proven that top modern games (DirectX 10, 11) run just as good as on the same machine without SoftXPand, so this is a pretty artificial limitation! So, can I somehow hack my current session so it doesn't look like a terminal server session anymore? I. E. #include <windows.h> #pragma comment(lib, "user32.lib") BOOL IsRemoteSession(void) { return GetSystemMetrics( SM_REMOTESESSION ); } Will return FALSE? (Not a programming question! Just an example how programs detect if they're in a terminal server session!)

  Read the article

• Python not Working in Vim

  - by jdg

  I have a new install of VIM from the automatic windows installer: gvim73_46.exe I have Python 2.7 (32 bit) installed. If I open gvim, and type: :set python? I get E518: Unknown option. If I try typing: :python 'hello' Vim crashes. What could be wrong? Here are the contents of :version in case they are helpful, although python is installed, and it is using Python 2.7. I also checked, and C:\Windows\System32\python27.dll is where it should be... I am really lost here. Does anyone have any ideas as to what is going wrong? VIM - Vi IMproved 7.3 (2010 Aug 15, compiled Oct 27 2010 17:59:02) MS-Windows 32-bit GUI version with OLE support Included patches: 1-46 Compiled by Bram@KIBAALE Big version with GUI. Features included (+) or not (-): +arabic +autocmd +balloon_eval +browse ++builtin_terms +byte_offset +cindent +clientserver +clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +conceal +cryptv +cscope +cursorbind +cursorshape +dialog_con_gui +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +gettext/dyn -hangul_input +iconv/dyn +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap -lua +menu +mksession +modify_fname +mouse +mouseshape +multi_byte_ime/dyn +multi_lang -mzscheme +netbeans_intg +ole -osfiletype +path_extra +perl/dyn +persistent_undo -postscript +printer -profile +python/dyn +python3/dyn +quickfix +reltime +rightleft +ruby/dyn +scrollbind +signs +smartindent -sniff +startuptime +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white +tcl/dyn -tgetent -termresponse +textobjects +title +toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -xfontset -xim -xterm_save +xpm_w32 system vimrc file: "$VIM\vimrc" user vimrc file: "$HOME_vimrc" 2nd user vimrc file: "$VIM_vimrc" user exrc file: "$HOME_exrc" 2nd user exrc file: "$VIM_exrc" system gvimrc file: "$VIM\gvimrc" user gvimrc file: "$HOME_gvimrc" 2nd user gvimrc file: "$VIM_gvimrc" system menu file: "$VIMRUNTIME\menu.vim" Compilation: cl -c /W3 /nologo -I. -Iproto -DHAVE_PATHDEF -DWIN32 -DFEAT_CSCOPE -DFEAT_NETBEANS_INTG -DFEAT_XPM_W32 -DWINVER=0x0400 -D_WIN32_WINNT=0x0400 /Fo.\ObjGOLYHTR/ /Ox /GL -DNDEBUG /Zl /MT -DFEAT_OLE -DFEAT_MBYTE_IME -DDYNAMIC_IME -DFEAT_GUI_W32 -DDYNAMIC_ICONV -DDYNAMIC_GETTEXT -DFEAT_TCL -DDYNAMIC_TCL -DDYNAMIC_TCL_DLL=\"tcl83.dll\" -DDYNAMIC_TCL_VER=\"8.3\" -DFEAT_PYTHON -DDYNAMIC_PYTHON -DDYNAMIC_PYTHON_DLL=\"python27.dll\" -DFEAT_PYTHON3 -DDYNAMIC_PYTHON3 -DDYNAMIC_PYTHON3_DLL=\"python31.dll\" -DFEAT_PERL -DDYNAMIC_PERL -DDYNAMIC_PERL_DLL=\"perl512.dll\" -DFEAT_RUBY -DDYNAMIC_RUBY -DDYNAMIC_RUBY_VER=191 -DDYNAMIC_RUBY_DLL=\"msvcrt-ruby191.dll\" -DFEAT_BIG /Fd.\ObjGOLYHTR/ /Zi Linking: link /RELEASE /nologo /subsystem:windows /LTCG:STATUS oldnames.lib kernel32.lib advapi32.lib shell32.lib gdi32.lib comdlg32.lib ole32.lib uuid.lib /machine:i386 /nodefaultlib gdi32.lib version.lib winspool.lib comctl32.lib advapi32.lib shell32.lib /machine:i386 /nodefaultlib libcmt.lib oleaut32.lib user32.lib /nodefaultlib:python27.lib /nodefaultlib:python31.lib e:\tcl\lib\tclstub83.lib WSock32.lib e:\xpm\lib\libXpm.lib /PDB:gvim.pdb -debug

  Read the article

• ps aux as non-root doesn't show all processes

  - by JMW

  hi, i'm using an ubuntu 10.04 server... when i run ps aux as root i see all processes when i run ps aux as nonroot i see JUST the processes of the current user after a bit of research i found the following solution: root@m85:~# ls -al /proc/ total 4 dr-xr-xr-x 122 root root 0 2010-12-23 14:08 . drwxr-xr-x 22 root root 4096 2010-12-23 13:30 .. dr-x------ 6 root root 0 2010-12-23 14:08 1 dr-x------ 6 root root 0 2010-12-23 14:08 10 dr-x------ 6 root root 0 2010-12-23 14:08 1212 dr-x------ 6 root root 0 2010-12-23 14:08 1227 dr-x------ 6 root root 0 2010-12-23 14:08 1242 dr-x------ 6 zabbix zabbix 0 2010-12-24 23:52 12747 [...] my first idea was, that it got mounted in a weird way: /etc/fstab is ok and it doesn't seem to be mounted in an weird way... my second idea was, that there might be a rootkit: but it's not a rootkit... rkhunter tells me, that there is no rootkit installed... i don't know if it is since the machine got installed or came with an update. i've just installed zabbix-agent on the machine and realized, that it didn't work properly... What could have caused such strange permissions (500) and how can i set it back to an normal level (555) ? Crazy, i've never seen something like that... thanks in advance for any help and merry christmas :) see you

  Read the article

• Can I enable discards on a LUKS-encrypted ssd drive in RHEL6 (and do I need to)?

  - by Dan Nestor

  I have a RHEL 6.4 workstation, running on a LUKS-encrypted LV residing on a SSD. I found RedHat documentation stating that dm_crypt does not currently support TRIM passthrough, however I also found other sources that state the opposite (albeit for other distributions) and even that discards are not needed for recent SSD drives which use some sort of automatic garbage collection. So: 1) Can I enable TRIM/discards with my setup? 2) Do I need to, for optimal disk performance? Thanks for your thoughts.

  Read the article

• Shut Out of XP - No Admin Password or CDR

  - by ashes999

  I inherited an old WinXP/Linux dual-boot machine from the stoneage. Because it has Linux, the regular boot process is replaced with the Fedora boot loader; I cannot, therefore, press F8 strategically to tell my PC to boot from CD. Even if I could, it's a moot point; the CDR doesn't seem to recognize any CDs. To make things worse, there's no option to network boot. The original user is probably long gone; I don't know the password for any of the Administrator group users. I can login using my corp account, but that's unprivileged on this machine. Since I'm not an admin, I can't do crazy things, like looking at boot.ini. Or deleting files. I only have 500MB free on my C drive. I'm pretty sure I can't boot from a USB, since I didn't see any settings for this in my BIOS. How can I get admin access for my user? Edit: Things I've tried: Boot from CD (CD not recognized) Launch CD from XP (CD not recognized) Install Daemon Tools Lite so I can install from an ISO -- don't have admin privileges XP password recovery tool -- requires admin privileges Adding an admin user -- no access to Control Panel Users since I'm not an admin Logging in as both the admin users on the system (trying some standard passwords) Using Fedora to chntpw (the Fedora version installed is ancient -- 2.7)

  Read the article

• 10 GigE interfaces limits single connection throughput to 1 Gb on a ProCurve 4208vl

  - by wazoox

  The setup is as follow : 3 Linux servers with Intel CX4 10 GigE controllers and an X-Serve with a Myricom 10 GigE CX4 controller are connected to a ProCurve 4208vl switch, with a myriad of other machines connected through good ol' 1000 base-T. The interfaces are actually set up as 10 Gig, according to both the switch monitoring interface and the servers (ethtool, etc). However a single connection between two 10 GigE equipped machines through the switch is limited to exactly 1Gb. If I connect two of the 10 GigE machines directly with a CX4 cable, netperf reports the link bandwidth as 9000 Mb/s. NFS achieves about 550 MB/s transfers. But when I'm using the switch, the connection tops at 950 Mb/s through netperf and 110 MB/s with NFS. When I open several connections from 3 of the machines to the 4th, I get 350 MB/s of NFS transfer speed. So each individual 10 GigE ports actually can reach much more than 1 Gb, but individual connections are strictly limited to 1 Gb. Conclusion : the 10 GigE connection through the switch behaves exactly like a trunk of 10 1 Gb connections. That doesn't make any sense to me, unless HP planned these ports only for cascading switches or strictly for many-clients-to-single-server connection. Unfortunately this is NOT the envisioned setup, we need big throughput from machine to machine. Is this a not-so-known (or carefully hidden...) limitation of this type of switch? Should I suggest seppuku to the HP representative? Does anyone have any idea on how to enable a proper behaviour ? I upgraded for an hefty price from bonded 1Gb links to 10 GigE and see exactly ZERO gain! That's absolutely unacceptable.

  Read the article

• System Slow After Uprading Ubuntu

  - by Aragon N

  I have an Ubuntu network machine which has release of 10.04.1 LTS Lucid. On this system I have Apache, PostgreSQL and django. For some app. development I have to install PGP and php-curl. Due to being on network, I have exported a VMware machine to the Internet and firstly I have upgraded the system and then installed php5 packages on it. I don't know is it all about django or apache configuration. Maybe some Apache settings had changed. In this case in apache where I have to look at ? After all replacing it with its old place, I see that the new system query is slow according to another. Old system query time : 140 ms New system query time : 9.11 s I have checked /etc/network interface and it seems there is no problem. I have checked /etc/resolv.conf and it seems OK I have checked /etc/nsswitch.conf and only host section is different from old one which old system has hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4 and then I have checked time host -t A services.myapp.com and I got real 0m0.355s user 0m0.010s sys 0m0.020s and I have checked apache2 HostnameLookups : find /etc/apache2/ -type f | xargs grep -i HostnameLookups It returned : /etc/apache2/apache2.conf:# HostnameLookups: Log the names of clients or just their IP addresses /etc/apache2/apache2.conf:HostnameLookups Off and now what can I have to check for boosting my system as before?

  Read the article

• How to configure CISCO switch 2960 for port-based address allocation on a single port only?

  - by Jack

  CISCO 2960 allows you to configure so-called Port-Based address allocation. It makes the switch to associate IP address it is giving out via DHCP with port-identifier, which is random, switch created identifier. In practice it means that any machine connected to such configured port will always get the same IP address, regardless of what that machine's MAC address is. I want to have that feature configured on --some ports-- only. But no matter what commands I try it seems that this can only be done for all ports, all for none. Even though CISCO manual seems to indicate there's both global and per-port command to enable that. Here are relevant commands from CISCO manual: configure terminal ip dhcp use subscriber-id client-id (this configures the DHCP server to globally use the subscriber ID as the client ID on all incoming DHCP messages) interface FastEthernet0/1 ip dhcp server use subscriber-id client-id (Optional: Configures the DHCP server to use the subscriber ID as the client ID on all incoming DHCP messages on the interface) but it appears if I configure only per-interface than there's no effect at all, if I configure globally and per interface - CISCo behaves as if all ports were configured to use that feature. Any ideas?

  Read the article

• Raid1 with active and spare partition

  - by Daniel Baron

  I am having the following problem with a RAID1 software raid partition on my Ubuntu system (10.04 LTS, 2.6.32-24-server in case it matters). One of my disks (sdb5) reported I/O errors and was therefore marked faulty in the array. The array was then degraded with one active device. Hence, I replaced the harddisk, cloned the partition table and added all new partitions to my raid arrays. After syncing all partitions ended up fine, having 2 active devices - except one of them. The partition which reported the faulty disk before, however, did not include the new partition as an active device but as a spare disk: md3 : active raid1 sdb5[2] sda5[1] 4881344 blocks [2/1] [_U] A detailed look reveals: root@server:~# mdadm --detail /dev/md3 [...] Number Major Minor RaidDevice State 2 8 21 0 spare rebuilding /dev/sdb5 1 8 5 1 active sync /dev/sda5 So here is the question: How do I tell my raid to turn the spare disk into an active one? And why has it been added as a spare device? Recreating or reassembling the array is not an option, because it is my root partition. And I can not find any hints to that subject in the Software Raid HOWTO. Any help would be appreciated. Current Solution I found a solution to my problem, but I am not sure that this is the actual way to do it. Having a closer look at my raid I found that sdb5 was always listed as a spare device: mdadm --examine /dev/sdb5 [...] Number Major Minor RaidDevice State this 2 8 21 2 spare /dev/sdb5 0 0 0 0 0 removed 1 1 8 5 1 active sync /dev/sda5 2 2 8 21 2 spare /dev/sdb5 so readding the device sdb5 to the array md3 always ended up in adding the device as a spare. Finally I just recreated the array mdadm --create /dev/md3 --level=1 -n2 -x0 /dev/sda5 /dev/sdb5 which worked. But the question remains open for me: Is there a better way to manipulate the summaries in the superblock and to tell the array to turn sdb5 from a spare disk to an active disk? I am still curious for an answer.

  Read the article

• Google account gives ERR_SSL_BAD_RECORD_MAC_ALERT errors

  - by Kjensen

  A couple of days ago, I started being unable to connect to accounts.google.com, which handles logins to all kinds of google services. I get this error in Chrome: Error 126 (net::ERR_SSL_BAD_RECORD_MAC_ALERT): Unknown error. In IE I get this: I assume it is the same error, just wrapped up. I run Win8 RTM. On the SAME machine, using the same network card, in a VMWare workstation image running Win7, I am able to connect perfectly. On another of my machines on my network, I am also still able to connect with no problem. My girlfriend uses the same network and has also complained a couple of times about this error (google calendar) - but this is anecdotal, since her technical troubleshooting abilities stop at "xxxx is broken". Her machine runs Win7. ;) I have rebooted, cleared cookies, do not run any antivirus/firewall, have not changed network config. The first 3-4 days after installing Win8, I did not have any problems. I have also searched, and found a hint about enabling SSL2.0 in connection settings, which did not help. Anybody know something about this error and what I can do to fix it?

  Read the article

• Problems with 5.1 digital out on Ubuntu 12.04

  - by user895319

  I've recently bought a new PC, installed Ubuntu and am now unable to get 5.1 digital sound working. Simple analogue stereo works fine on both the front and rear connectors. On my old box I connected the coax connection from my soundcard to my surround sound amplifier, set Settings-Sound to "Digital Stereo Duplex" and it worked. My old soundcard doesn't fit in my new machine so I'm using the built-in sound hardware. I'm connecting the combination output socket on the back of the PC via the same cable to my surround amp as before. The MB is an MSI Global H61M-P31 with an RealTek ALC887 sound chip. When I go to Settings-Sound I only see "Headphone Built-in Audio" and "Analogue Output Built-in Audio" - no digitial options. The output from aplay -l is: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC887-VD Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Hardware device with all software conversions While googling for ALC887 I've seen some references to "ALC887 -VD Analog" and some to "ALC887 -VD Digital". Does anyone know if I need to force it to chance mode somehow? It's worth mentioning that when I set the output to 5.1 digital surround in Windows 7 on the same machine I still don't get any sound so it's not a unique Linux problem. Thanks for any help.

  Read the article

• best way to go about cost-benefit analysis on hardware

  - by Michael

  I'm looking to build a low-end computational server (my jargon in this field is especially limited so if someone can state that better please change that to meet jargon). I'm basically running computational fluid dynamics programs, large matrix computations and bioinformatics code. What would be the best way to approach cost/benefit analysis on what to put in the system? Perhaps even more general: How does one approach cost/benefit analysis on hardware theoretically (doing the analysis before building the machine)?

  Read the article

• Network card/driver stops under heavy load

  - by Uwe Keim

  Since about approx. 2 month, I do have the following issue with my approx. 1 year old development machine (Windows 7, 64 bit): When doing network intensive operations, like e.g. executing some SQL script on a remote SQL server to select or update 1000 of records, the network card stops working. I.e. suddenly, No network connection is present anymore. No internet, no local connection, simply nothing. The only resolution so far I found is to disable my network card and then simply enable it back, like in the following screenshots: 1.) Click "Deactivate" 2.) Click "Activate" (German screenshots only, sorry) Now this is an acceptable solution to work around this issue, but I would love to have this fixed, since it suddenly stops me from working when I'm connected remotely via VPN/RDP on my machine (Win7 64bit). So my question is: Could you imagine a possible cause for this issue and give some hints how to hunt/resolve it? I could imagine that this is a driver issue, a hardware issue or even some kind of background software issue like a software firewall or a virus scanner.

  Read the article

• Is it possible to either abort or interrupt and later continue a lvconvert -m1 operation?

  - by SLi

  I have run the command lvconvert -m1 rootvg/newroot /dev/sdb to convert a linear logical volume to a mirrored one. The operation has not yet finished; I interrupted the command with ctrl-c at around 10% mark, but the operation seems to be running in the background anyway. Is it possible to either 1) Abort the lvconvert operation and revert to the state before it? (This would be my preferred option) 2) To safely interrupt the operation and resume it later?

  Read the article

• Forward mDns from one subnet to another?

  - by user37278

  Is there an ipfw rule that can easily forward mDns packets from one subnet to another? I have a Snow Leopard Server machine serving as the gateway between the two subnets and would like for machines in each subnet to see the services available in the other subnet. The gateway machine is already confirmed as configured correctly such that packets route correctly between the two subnets (ping works, traceroute shows the subnet hop, etc). My problem in designing a ipfw rule is that I don't know how to instruct that I would like multicast packets addressed to 224.0.0.251:5353 on en0 to be addressed to the same ip/port but on fw0 (the other interface). I attempted a rule such as fwd 192.168.10.1 log udp from 192.168.1.0/24 to 224.0.0.251 recv en1 to force the packet to hop over to the other interface (from en1 to fw0), but no dice. The ipfw log shows that the rule is being triggered by packets, but tcpdump isn't showing any packets on the other interface. Also, the only other firewall rules in place are the divert port 8668 and rule #65535 "allow any to any". Any suggestions? Thanks.

  Read the article

• Find out when a system went down?

  - by Clinton Blackmore

  I have a Mac OS X 10.5 server, with a RAID set in it, that went down due to a power outage on Thursday, and the machine is not happily booting right now*. It is possible to find out when the machine went down, while not booted off the internal drive? (I'm booted off an external drive, waiting for the RAID sets to initialize.) Normally, I'd run last. The man page doesn't indicate that I can run it against a different startup volume. It looks possible to parse /var/log/utmpx, but I don't think it'd be worthwhile to try to do that from scratch for this one-off problem. * I'm still trying to figure out why it isn't happy, and may ask a follow-up question. Right now I can see that UserNotificationCenter crashed repeatedly early Thursday morning, and that securityd, mdworker, and ARDAgent crash shortly after startup [I think -- I want to verify when the box went up and down]. The login window does not come up right (I think it is crashing or not able to cope with a dead securityd). The box is supposed to be set to go down when the UPS tells it power is out; at the moment, I'm wondering if it went down, and turned back on multiple times! I sure hope not.

  Read the article

• Loading a big database dump into PostgreSQL using cat

  - by RussH

  I have a pair of very large (~17 GB) database dumps that I want to load into postgresql 9.3. After installing the database packages, learning more or less how to use them, and fiddling around a little on various StackExchange pages (particularly this question), it looks like a proper command for me to use is something like: cat mydb.pgdump | psql mydb because of the format the dump is in. My machine has 16 GB of RAM, and I'm not familiar with the cat command but I do know that my RAM is 99% exhausted and the database is taking a while to load. My machine isn't non-responsive to the point of hanging; I can run other commands in other terminal windows and have them execute at a reasonable clip, but I am wondering if cat is the best way to pipe in the file or if something else is more efficient? My concern is that maybe cat could be using up all the RAM so the database doesn't have much to work with, throttling its performance. But I'm new to thinking about RAM issues like this and don't know if I'm worrying about nothing. Now that I think about it, this seems to be more of a question about cat and its memory usage than anything else. If there is a more appropriate forum for this question please let me know. Thanks!

  Read the article

• postmap: fatal: open database /etc/postfix/sasl_passwd.db: Permission denied

  - by James Benders

  Hi, I'm configurint Postfix to use external smtp. For this, I use the following tutorial: http://carlton.oriley.net/blog/?p=31 After following it, I found in the logs that /etc/postfix/sasl_passwd.db couldn't be read. The file didn't exist. I used postmap hash:/etc/postfix/sasl_passwd (http://postfix.state-of-mind.de/patrick.koetter/smtpauth/smtp_auth_mailservers.html) as root, but I get: postmap: fatal: open database /etc/postfix/sasl_passwd.db: Permission denied Why do I get this? Thanks.

  Read the article

• Ram question in VMware Server 2

  - by ToreTrygg

  Hi, I understand from the VMware Server 2 documentation that VMware Server 2 is capable of running a 64-bit guest OS underneath a 32-bit host OS, as long as the hardware running the box is 64-bit capable. Here's my situation. We currently have an underutilized XEON X3220 Quad Core 64bit Server, running Server 2003, 32-bit and 2gb of RAM (the motherboard is capable of 8gb ram). The server is currently used mainly for file and print services. It is also running Active Directory, Novell eDirectory and Groupwise 6.5. We are planning a micration to Microsoft Exchange, so the Novell eDirectory and Groupwise services will eventually be purged from this box, leaving only Active Directory, File and Print services. Being that this server is underutilized we are hoping to save hardware costs and virtualize our new Exchange investment. My question is this. Will VMware allow access to the "invisible" extra memory that Windows 32-bit won't see. Meaning, if we increase the full amount of system ram to 8gb (yes, I know the 32-bit host OS will only see a maximum of 4gb), will I be able to assign maybe 5gb to the new Server 2008 64-bit OS running Exchange and leave 3gb for the Guest OS (or maybe even a 6, 2 split). The second part of that would be, would it be better to just convert the main OS currently running to an image, convert the machine itself to ESXi and run both OSes as images under ESXi. Downtime for this box is critical, so my preference is most definitly with the first option because it presents very minimal downtime. Doing the second would make downtime quite a few hours to image the machine and then convert the image to a VMware Image.

  Read the article

• Why is Windows 7 slow resume from suspend?

  - by John McC

  I have Windows 7 on an HP Mini 5101. It is can be very slow to resume from suspend (not hibernate) state. The time from power on to the login prompt varies from say 10 sec to over a minute. This machine mainly gets used for sofa surfing so usually only Firefox and gtalk are running. Any suggestions on how to achieve Mac-like start-up or suggestions on how to track down the problem appreciated.

  Read the article

• Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

  - by Matt Taylor

  I recently did a full upgrade of Windows 7 on my Thinkpad. Everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen before the Windows logo appears. Disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this won't boot with battery plugged in is greatly appreciated. I need to take this battery out on the road/trains, etc. A little more detail on this story. The battery I had inserted when doing the (failed) boot was a long life battery. I have not tried inserting this battery when Windows is logged in. I have another (normal life) battery that I have charged up within Windows. It has just got to 100% and I am about to reboot with it in. I am using the Lenovo power manager to diagnose the battery - all seems OK. I will report back shortly as to the outcome. OK, so I chose the reboot option from within Windows, the machine seemed to shutdown okay, but then stalled. It didn't turn off completely and didn't reboot, but just sat, with the fan humming, somewhere in between! I had to hold the power button in for a few seconds until the fan stopped and then hit the power button again to boot the machine from fresh. One good thing, with this battery (the normal one) it booted into Windows 7 the first time with a battery! So, now I have rebooting issues. I have 3 errors in the event log: A timeout was reached (30000 milliseconds) while waiting for the lxdxCATSCustConnectService service to connect. The lxdxCATSCustConnectService service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. The following boot-start or system-start driver(s) failed to load: cdrom Any thoughts?

  Read the article

< Previous Page | 405 406 407 408 409 410 411 412 413 414 415 416  | Next Page >