Search Results

Search found 3773 results on 151 pages for 'paul james'.

Page 41/151 | < Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >

  • What is the best memory supported by Asus Rampage Formula (1) motherboard

    - by James
    I'm rebuilding a PC from old components I have and I want to know what are the best ram sticks for the Asus Rampage Formula (The first motherboard in the Rampage Formula range) According to the Asus website (HERE) the maximum supported memory is 8GB but when I search through the memory compatibility list there's nothing above 2046mb and the motherboard only supports single or dual-channel memory. Can anyone point me in the direction of a more comprehensive list of compatible memory? Or does anyone know where I can ask about memory compatibility? Note: As far as I know, this model motherboard is no longer in production.

    Read the article

  • Network attached external harddrive from another computer.

    - by Paul Knopf
    I have a server that is setup in raid. It is on the same network as my main computer. I would like to have some of the memory on my server to act as a network attached drive on my main computer. Basically, I want it to be a new data drive (similar two C:\, but 2nd drives are mostly E:). That way, I can reformat my main computer without loosing any important data. And the data that is saved (on server E:\ drive) is secured via raid mirroring.

    Read the article

  • Running 32bit eclipse on 64bit windows.

    - by james
    I am trying to use a 32bit installation of eclipse on my 64bit windows machine. I have eclipse extracted to my C: Drive and Java installed in ProgramFiles(x86) When I go to start eclipse I get the error:Failed to load the JNI shared Library"C:Program Files(x86)\Java\jre6\bin\jvm.dll" I looked and the file is not there. I am setting something up wrong?Just did a fresh install of Java before trying to run eclipse.

    Read the article

  • Failover Issuer CAs without Clustering

    - by James Santiago
    I am attempting to setup a Certificate Authority with some failover capabilities for the issuer CAs. I have an offline root CA and am attempting to setup two subordinate CAs on our domain which will handle issuing certificates. I'm trying to determine the architecture needed for these two CAs to allow one to go down and the other to take over without the use of failover clustering, as the two are in different geographic locales. Are there documents regarding this setup?

    Read the article

  • what reverse proxy server will direct traffic to healthy servers whose health is based on a result string

    - by joshua paul
    what reverse proxy server will direct traffic to healthy servers whose health is based on a result string?? ideally i'd like something like dnsmadeeasy or ultradns - lol - but for reverse proxy i have looked at pound, delegate, ha proxy, squid, varnish, nginx, apache, and cherokee but can't see that they will work - they only test for HTTP result code scenario client request www.aaa.com www.aaa.com is a reverse proxy reverse proxy looks at "test.php" on server 1.aaa.com, 2.aaa.com and 3.aaa.com for result string "OK" if the server is "OK" then proxy requests to them help!

    Read the article

  • Fedora12, XP and connection sharing via iptables

    - by Paul L
    Just a quick question ( I Hope ) To find out if what I'm trying is even possible. I am trying to share internet connection with Fedora12 as default gateway and XP machine hooked up via NIC using iptables commands as shown in Mark Sobell's book 'A Practical Guide To Fedora And Red Hat Enterprise Linux' These are the commands as placed in /etc/rc.local iptables -A FORWARD -i eth1 -o eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT iptables -A FORWARD -j LOG iptables -t NAT -A POSTROUTING -o eth1 -j MASQUERADE I did flip the in and out parameters to match my NIC configuration ( as opposed to example from book ) but other than that followed example. One thing to note is that Sobell did not mention whether this should work with mix of Linux and XP. One other note ( maybe meaningless ) is that I do have samba working between the two machines. Thanks for any insights anyone might have. PL

    Read the article

  • How to automate wIntegrate import/export?

    - by Paul Ayling
    Our company uses pic database and wIntegrate 4.02 to interface with. How would I go about automating the .wis files for importing and exporting through wIntegrate? Is there some type of macro, software solution or built in routine I can use? At the moment I manually login to pic using wIntegrate and goto run - querybuilder and select the desired .wis script for importing and exporting data and select ok to run. This is not a solution, it needs to be automated. Anyone? Is there some type of point a click freeware recording software? I hate to do a hack job like that but I'm running out of ideas and no one seems to have worked with this software before...

    Read the article

  • Public IP Routing over Private GRE tunnel

    - by Paul
    I have a GRE tunnel configured between two linux boxes. The tunnel works fine. I can ping from each host the other private ip. Head privateip: 10.0.0.1 publicip: 8.8.8.8 Tail privateip: 10.0.0.2 publicip: 7.7.7.7 The public IP on Tail has the network block 9.9.9.0/23 statically routed over the 7.7.7.7 interface. The idea is to make the 9.9.9.0/23 ips work on servers on the 8.8.8.8 network. I configure the tail host to route the /23 block. I mounted a 9.9 IP on the head server. I can ping the 9.9 ip from the tail to the head. I can't ping the 9.9 ip from the public internet. I think I need to add some other routes because of gateway issues, but I can't seem to wrap my mind around it (not a router guy, just beating my way through something that I have never done before and vaguely understand) --danks

    Read the article

  • Does the Windows "Sources" folder need copied to C: like the "i386" folder did?

    - by James Watt
    On all flavors of Windows prior to Windows Vista, the Windows install CD contained a folder called i386. After installing Windows, this folder is suppose to be copied to the C: drive. Once the folder has been copied, if user is ever installing a program or windows updates that require the Windows install CD, it will retrieve the files from the hard drive INSTEAD of prompting for the Windows CD. On new versions of Windows, including Windows Vista, Windows 7, Server 2008 and Server 2008 R2, the i386 folder has been renamed to "sources". Should this folder be copied to the hard drive? Or do the new versions of Windows work differently (i.e. by installing all features on the hard drive to eliminate the need for ever prompting the user to insert their disc.) It does not hurt to copy the sources folder, so I have been doing it. But if I could eliminate time wasted it would make installations faster which helps my customers' bottom line.

    Read the article

  • Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host

    - by Paul J. Warner
    I am having an issue with a program where after 6 mins +- 5 secs we get the above exception. Some more info about the exception stacktrace is below. This all happens pretty religiously, 6 mins goes by and bam the following 3 exeptions. We have the application installed in 2 other environments and it is working fine there. I am hoping to find some server settings either IIS 6 or Server 2003 settings that may be causing this issue to occur. I have reviewed some of the similar questions and don't see very many answers. I am hoping that maybe the information I have provided may help a little bit. 208741,Exception,,,,2011-06-21 00:30:14.193,SERVERNAME,2624,1,CLIENTNAME,The underlying connection was closed: An unexpected error occurred on a receive. , at System.Web.Services.Protocols.WebClientProtocol.GetWebResponse(WebRequest request) at System.Web.Services.Protocols.HttpWebClientProtocol.GetWebResponse(WebRequest request) at Microsoft.Web.Services3.WebServicesClientProtocol.GetResponse(WebRequest request, IAsyncResult result) at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) at System.Net.Sockets.NetworkStream.Read(Byte[] buffer, Int32 offset, Int32 size) at System.Net.FixedSizeReader.ReadPacket(Byte[] buffer, Int32 offset, Int32 count) at System.Net.Security._SslStream.StartFrameHeader(Byte[] buffer, Int32 offset, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.Security._SslStream.StartReading(Byte[] buffer, Int32 offset, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.Security._SslStream.ProcessRead(Byte[] buffer, Int32 offset, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.TlsStream.Read(Byte[] buffer, Int32 offset, Int32 size) at System.Net.PooledStream.Read(Byte[] buffer, Int32 offset, Int32 size) at System.Net.Connection.SyncRead(HttpWebRequest request, Boolean userRetrievedStream, Boolean probeRead),2004437127,114,1 208742,Exception,,,,2011-06-21 00:30:14.227,SERVERNAME,2624,1,CLIENTNAME,Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host. , at System.Net.Sockets.NetworkStream.Read(Byte[] buffer, Int32 offset, Int32 size) at System.Net.FixedSizeReader.ReadPacket(Byte[] buffer, Int32 offset, Int32 count) at System.Net.Security._SslStream.StartFrameHeader(Byte[] buffer, Int32 offset, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.Security._SslStream.StartReading(Byte[] buffer, Int32 offset, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.Security._SslStream.ProcessRead(Byte[] buffer, Int32 offset, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.TlsStream.Read(Byte[] buffer, Int32 offset, Int32 size) at System.Net.PooledStream.Read(Byte[] buffer, Int32 offset, Int32 size) at System.Net.Connection.SyncRead(HttpWebRequest request, Boolean userRetrievedStream, Boolean probeRead),2004437127,114,1 208743,Exception,,,,2011-06-21 00:30:14.287,SERVERNAME,2624,1,CLIENTNAME,An existing connection was forcibly closed by the remote host , at System.Net.Sockets.NetworkStream.Read(Byte[] buffer, Int32 offset, Int32 size),-691097507,62,1

    Read the article

  • cmd.exe version comparison?

    - by Paul
    When using batch files or console applications on Windows servers the window in question can allow text to be hightlighted (marked) for copying and pasting. Doing this pauses the batch/application and it will only resume after the copy operation. Or this is what I thought to be true. Recently on a Windows 2003 R2 SP2 server I noted that whilst the scrolling was paused the operations were not. Does anyone know if my description in the 1st para is true for older windows is not true for Windows 2003 R2 SP2 when it changed a full version comparison table for cmd.exe across different OS' ? Thanks for reading (Windows 2000 tag as that was the OS I used most before 2003 R2)

    Read the article

  • Jailkit - allowing use of Java/Python

    - by James hooker
    I'm looking to allow Jailed users to use JAVA (JRE) to execute their own Java files, similarly with Python to execute py scripts. I've tried adding the JAVA binary (/usr/bin/java) to a jail using the following jk_cp /path/to/jail /usr/bin/java This seems to copy some of the libraries across, aswell as the Java binary itself, however the jailed user is still unable to execute Java. It complains first of all of a missing lib called libsli.so. I copied that across and it then complains about libjava.so which I proceeded to copy across to, to no avail. Does anyone have experience with enabling the execution of Java within a jailed environment? This is under Ubuntu 10.04 64-bit, with Jailkit 2.11.

    Read the article

  • Determine the time difference between two linux servers

    - by Paul
    I am troubleshooting a latency network issue on a network. It is probably a nic or cabling issue, but while I was going through the process of figuring it out, I was looking at the timings of a ping packet leaving a network card and arriving at another server. Both linux. So I have tcpdump running on both, and I issue a ping from one to the other, and back again, and looking at the timing differences might have shed light on where the latency is coming from. It is an academic exercise now, as I need to eliminate some more fundamental causes, but I was curious as to how this could be achieved. Given that ntpd is installed and running on two servers, how can I confirm the current time discrepency between the two servers, to whatever level of accuracy is possible - given that we are talking about latency on a local lan, which is ideally a millisecond or so. NTP itself is accurate to a couple of ms under good conditions, and as both servers are in the same environment, they should (presumably) achieve a similar level of accuracy, and so should have a time discrepency between them of a only few ms - but how can I check this?

    Read the article

  • Configuring Fortigate OS4 for FTPS

    - by Paul
    I configured iis7 ftp to allow ssl connections. I set the ssl firewall to use ports 50000-50050. If I set up a custom service on my fortigate firewall for ftps with source ports 990-50050 and destination ports 990-50050, set it to a firewall policy and connect from a client it connects and works successfully. If I create a service FTPS Control with source port 990 and destination port 990 and another service,FTP Data with source ports 50000-50050 and destination ports 50000-50050 add them to a group FTPSSL, replace the ftps policy with FTPSSL and try connecting it tries to connect to port 990 and eventually times out. Is there a way to configure the service to only use the ports I need and not every port from 990 up?

    Read the article

  • Can I run more than 4 virtual machines using Hyper-V Windows Server 2008 R2 Enterprise Edition as th

    - by James Holland
    I understand that a single Windows Server 2008 R2 Enterprise Edition license includes 4 free guest virtual machines using Hyper-V. Suppose I do that, and have 4 VMs running, but then want to expand. If I separately purchase additional Windows licenses, or I consolidate a machine with an existing license, can I spin up a 5th, 6th virtual machine (presuming there are enough CPU/RAM resources on the host)? Or does the host OS limit the number of virtual machines allowed?

    Read the article

  • How should I host a site that could potentially get a short spike in traffic of 1000%+

    - by James Simpson
    This is a purely theoretical question, but what if I had a site that would normally only get a couple thousand hits a day, but for a few days each month that could shoot to several hundred thousand or even several million hits over the period of 1-3 days. The site would be pretty bare-bones (as in, 2-3 total pages with 1-2 max MySQL queries on each page and some PHP), so bandwidth wouldn't be the issue, but sheer volume taking down the site would be the main concern. Cloud hosting seems like the best way to go, but would something like Amazon EC2, MediaTemple, or something else be the right choice in this case?

    Read the article

  • Windows 8 shortcut keys via RDP

    - by Paul
    It is possible to access any of the new shortcut keys found in Windows 8 via RDP, such as those in the accepted answer in What are the new shortcuts for Windows 8?, without having to redirect all Win key combinations through to the remote session. I am using both local and remote at the same time, and so would prefer alternate shortcuts for the remote session. Such as the basic ones listed at the Microsoft site here, and for example Alt+Home will return you to the Start screen. What about the more interesting shortcuts?

    Read the article

  • Print jobs sent to server OK, but then get deleted

    - by Paul Morrison
    I have 2 HP computers, one running Win XP SP3, one running Win7. I have a Lexmark X4270 All-in-One printer attached to the Win7 machine via a USB port. I can print OK from the Win 7 machine, but when I print from the WinXP machine, the print job shows up in both print queues (showing the same number of bytes - which is good!), but then the status gets changed to "Deleting - Sent to printer", and that status shows up in both print queues. The print job then stays there until I do a cancel, followed by a system restart. FWIW the owner is shown as Guest, but I have permission for Everyone set to print... I believe I have up-to-date drivers; I don't believe it's a firewall problem. What I would like to see is the Win7 machine's reason for deleting my print jobs - is there a diagnostic tool available? Also, I notice that the port for this printer on the WinXP machine is set to USB001 - I would have thought something like \servername\sharedprinter would be more appropriate - and I can see that in the list of ports, but the system doesn't let me change the port name from USB001... Could someone shed some light? I have spent hours on this! TIA BTW I can do file sharing, no problem!

    Read the article

  • How can I connect a Windows 8 PC to a Samba domain

    - by Paul
    I am using Samba 3, and want to join my Windows 8 PC to the Samba domain. Windows 8 cannot join out of the box, so I added the following registry entries: HKLM\SYSTEM\CurrentControlSet\Services\LanmanWorkstation\Parameters DWORD DomainCompatibilityMode 1 DWORD DNSNameResolutionRequired 0 And now it talks to the Samba server ok, however I get the following error: And I notice that the machine name created on the samba server does not match its name: win-8jq3fg1n74e$:x:30003:30003:Machine:/var/lib/nobody:/bin/false It is like it is using an internal name. The following is the error in the smb.log [2012/10/21 14:26:16.099520, 0] passdb/pdb_interface.c:348(pdb_default_create_user) _samr_create_user: Running the command `/usr/sbin/useradd -c Machine -d /var/lib/nobody -s /bin/false win-8jq3fg1n74e$' gave 9 [2012/10/21 14:26:28.143224, 0] lib/util_sock.c:474(read_fd_with_timeout) [2012/10/21 14:26:28.143420, 0] lib/util_sock.c:1441(get_peer_addr_internal) getpeername failed. Error was Transport endpoint is not connected read_fd_with_timeout: client 0.0.0.0 read error = Connection reset by peer.

    Read the article

  • Custom Icon for NFS Volume Mount - Possible for OSX?

    - by James
    We are naming our various network volumes after Planets! I renamed the Mercury.icns icon, to .VolumeIcon.icns and copied it over to the mount point folder of the NFS server. So far remounting the NFS share does not seem to employ this icon. Looking on the NFS server, there appears to be two VolumeIcon files. Can someone tell me what I am doing wrong? Permissions? Do I need a .DS_Store file there as well?? It shouldn't be this hard! EDIT: Should have mentioned, the NFS server is Ubuntu 12.04.1. NOT an OSX server.

    Read the article

  • Ubuntu 10.04 Server on Hyper-V Server R2 has sluggish install and command line

    - by Paul Hobart
    I've installed Ubuntu Server 10.04 (64 bit) on a Hyper-V Server R2. I've encountered two issues that I think are related: Very slow install Very slow command prompt The text-mode installer goes through a series of text-based prompt windows. It takes 7-10 seconds for each of these windows to draw on the screen. The end result is that every time I answer a prompt and hit enter I wait for 15 seconds while the screen redraws line by line. I can literally see each line of text being drawn (like the old 300 baud modems days). Once done installing, scrolling on the command line is super slow. For instance, if a simple command, like "ls", causes the screen to scroll, it will scroll very slowly. This happens on a fresh install. The server functions as a LAMP server and an OpenSSH server, but that's it (I don't even have any Virtual Hosts set up yet). AND this only happens on the Virtual Machine console. I access the console through Hyper-V Manager and don't have this problem on any of my other Virtual Machines. Also, this problem does NOT happen when accessing a shell through OpenSSH. How can I improve this performance issue?

    Read the article

  • Removing English - United States Language from Firefox Issue...

    - by Paul
    Win7 Home Prem 32bit Firefox 3.6.2 I noticed whilst typing a hotmail email in Firefox that the default language seems to be English/United States. As i am from the UK i thought i would add in the English/United Kingdom dictionary Addon which i have done. I have set this as the default Language. Is there anyway to remove the English/United States Dictionary? It is not an Addon so i'm guessing it's the built in Firefox default language and may be unremovable?

    Read the article

  • Shell Script Launching Child Processes

    - by Matt James
    Disclaimer: I'm totally new to shell scripting, but have quite a bit of experience in other languages like PHP and Obj-C. I'm writing my first daemon script. Here are the goals: I want it to run in the background I want it to be triggered by an init.d script that includes start/stop/restart commands I want each process in a loop to trigger its own subprocess. When the parent process kicked off by the init.d script is killed, I want the subprocesses to die as well. Essentially, I'm looking for the same kind of behavior that appears to be very common among software like apache, spamd, dovecot, etc. But, based on my research, I haven't found a single, simple answer as to how this kind of thing is achieved. Any help is greatly appreciated.

    Read the article

  • How to rewrite these URLs?

    - by Evik James
    I am brand new to URL rewriting. I am using an Apache rewriting module on IIS 7.5 (I think). Either way, I am able to do rewrites successfully, but am having trouble on a few key things. I want this pretty url to rewrite to the this ugly url: mydomain.com/bike/1234 (pretty) mydomain.com/index.cfm?Section=Bike&BikeID=1234 (ugly) This works great with this rule: RewriteRule ^bike/([0-9]+)$ /index.cfm?Section=Bike&BikeID$1 Issue #1 I want to be able to add a description and have it go to exactly the same place, so that the useful info is completely ignored by my application. mydomain.com/bike/1234/a-really-great-bike (pretty and useful) mydomain.com/index.cfm?Section=Bike&BikeID=1234 Issue #2 I need to be able to add a second or third parameter and value to the url to get extra info for the db, like this: mydomain.com/bike/1234/5678 mydomain.com/index.cfm?Section=Bike&BikeID=1234&FeatureID=5678 This works using this rule: RewriteRule ^bike/([0-9]+)/([0-9]+)$ /index.cfm?Section=Bike&BikeID=$1&FeatureID=$2 Again, I need to add some extra info, like in the first example: mydomain.com/bike/1234/5678/a-really-great-bike (pretty and useful) mydomain.com/index.cfm?Section=Bike&BikeID=1234&FeatureID=5678 So, how can I combine these rules so that I can have one or two or three parameters and any of the "useful words" are completely ignored?

    Read the article

< Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >