Search Results

Search found 14643 results on 586 pages for 'performance comparison'.

Page 410/586 | < Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >

• How do you explain ethernet cable problems to non networking people?

  - by Bryan McLemore

  We've recently been doing a large network migration in our datacenter. We've had a few cables in this start to deliver really bad pings (in excess of 500ms on a LAN) before they could be replaced. The cables we were replacing weren't made the best. They where all hand made and the runs were so short on some of them that the bend radius was definitely too tight. Some of them ran in bundles right in front of the heat exhaust of the power supplies. The cables were running ok until we started pulling the ones surrounding them out. Then a few started having the problem I mentioned above degrading performance and causing reliability issues. I'm trying to figure out the best way to explain this to non networking people. Is there any documentation that people could recommend or other methods?

  Read the article

• When is it time to buy a new hard drive, and what considerations go into buying a new hard drive?

  - by user1125620

  I've had my current hard drive for about 4-5 years now, and I've never had a problem with it before, but now it's making whirring noises. It's done this before and, last time, the noise did go away the next day, but I have accumulated quite a bit of information that I wouldn't want to lose on the drive. HD Tune Pro and Berlac Advisor both said the drive was healthy, and I wouldn't want to get a new one unless it was absolutely necessary or was going to show drastic performance improvements. My only knock against the drive would be that Visual Studio takes longer to load than I'd like it to. HD Tune Pro says the average read speed is 54.3MB/s. I'm not sure if that's good or bad, but it seems about average compared to similar drives on http://www.hdtune.com/testresults.html. Model #: WDC WD5000AAJS-22YFA0 So, should hard drives be replaced after a certain amount of time? Has mine reached that point? Would a new hard drive be any faster?

  Read the article

• What's faster for web-server virtualization ? (virtualbox or KVM)

  - by marc

  I have question, does anyone try to set up a webserver (debian) using virtualbox (x64) ? Right now i have few servers in KVM (x64) but i think it work slowly... Can i get something more (faster, performance) using virtualbox (x64)? On my home installation it looks very fast. Should i move to vbox against kvm ? I'm looking for answer from someone who have in virtualbox (x64) real server (can be headless) (debian/ubuntu) not windows xp or other home using things ;) I also got xp, 2k3, ubuntu in virtualbox (x86) and for me looking faster than kvm(x64). But it's hard to say anything without real tests done by multiple users not just one.

  Read the article

• Is paravirtualization evil?

  - by Daniel

  I have an VMWare ESX Server v3.5 with a few virtualized Debian Lenny VMs (kernel 2.6.22 with vmi) running Apache Tomcat 5.5. I enabled paravirtualization, and Disk IO increased from about 240MB/s to 380MB/s, making me a happy admin. The problem now is that my apache tomcat becomes deadlocked during startup, running with 200% CPU (I have 2 CPUS assigned to the VM), and don't know how to get both: A stable system and a fast system. I somewhere heared that paravirtualization is legacy anyway and won't be available on newer ESX servers. Is there a replacement for this seemingly performance-improving option, or is it discontinued becauses it is just unstable? What is the state of paravirtualization? Should I ignore it completely? Thanks for all answers in advance.

  Read the article

• What does motherboard RAM slot colors mean?

  - by totymedli

  I always saw that the motherboard RAM slots are colored in pairs, but never know what does it means. I just put the 2 RAM in, and after a few tries it always worked. But after I tried to install a third one it always throws me a blue screen of death. Is there an order how should I install RAM to the borad? What does the colors mean? Does they indicate performance boost opportunity or are they just a guide for installation?

  Read the article

• Need hard disk recommendation for linux home server.

  - by neotracker

  Hello, I'm planing to build a little linux homeserver. It will mainly be used for storage and maybe as an media pc. I plan to build a software raid5 with 4 1.5TB or 2TB hard drives. I already decided to use the Western Digital Caviar Green 1.5 TB drive, but then I read about some problems with the WD green series about many drives failing and that they are not recommended for raid anyway. Of course, I couldn't find much facts on the issues so I thought I just ask here ;-) What hard drives would you recommended for a software raid5 setup? As I only need it for storage, the whole thing doesn't have to be too fast. So I prefer a cheap price and silence to great performance.

  Read the article

• What type of security problems are mitigated by this .NET architecture?

  - by Jonno

  Given the following physical layout for a .NET web application: DB (sql server, windows) - No public route (no table access, only stored procs) Web Service DAL (iis, windows) - No public route (can be accessed by web server via port 80 and 443) Web Server (iis, windows) - Public route (only via port 80 and 443) What type(s) / examples of attack could be used to compromise the public web server but would be blocked by the Web Service DAL? i.e. can you think of concrete attack types that the DAL stops? Please note, I am interested only in the security aspect, not scaling / fault tolerance / performance / etc. In my mind if the web server has been compromised using an attack over port 80/443, then the same attack would work over port 80/443 to the Web Service DAL box.

  Read the article

• How do you handle the task of changing the schema of a production MySQL database?

  - by Continuation

  One of the biggest complaints I have heard about MySQL is that it locks up a table if you try to change its schema like adding a column or adding an index. By "locking up the table" does it mean I can neither read nor write to the table? Sometimes for hours? That seems a pretty severe limitations. I was going to use MySQL for my new project but this gives me pause. Is there a workaround for this? How do you handle the task of changing the schema of your production MySQL database? By the way someone told me Postgresql doesn't have this problem. Is that true - I can both read and write to a Postgresql table while changing its schema? Is there any performance penalty incurred? Would love to hear your experiences.

  Read the article

• Which modules can be disabled in apache2.4 on windows

  - by j0h

  I have an Apache 2.4 webserver running on Windows. I am looking into system hardening and the config file httpd.conf. There are numerous load modules and I am wondering which modules I can safely disable for performance and / or security improvements. Some examples of things I would think I can disable are: LoadModule cgi_module others like LoadModule rewrite_module LoadModule version_module LoadModule proxy_module LoadModule setenvif_module I am not so sure they can be disabled. I am running php5 as a scripting engine, with no databases, and that is it. My loaded modules are: core mod_win32 mpm_winnt http_core mod_so mod_access_compat mod_actions mod_alias mod_allowmethods mod_asis mod_auth_basic mod_authn_core mod_authn_file mod_authz_core mod_authz_groupfile mod_authz_host mod_authz_user mod_autoindex mod_dav_lock mod_dir mod_env mod_headers mod_include mod_info mod_isapi mod_log_config mod_cache_disk mod_mime mod_negotiation mod_proxy mod_proxy_ajp mod_rewrite mod_setenvif mod_socache_shmcb mod_ssl mod_status mod_version mod_php5

  Read the article

• Just how slow should my VPN be?

  - by David Heggie

  I have a VPN setup between a remote office with 2 ADSL connections (8Mb downstream, 512Kb upstream) and a main office with a 10Mb EFM connection (10Mb both up and down). The VPN is an IPSec connection using a DrayTek 2930 router for the ADSL and a DrayTek 3200 router at the EFM end. However, I'm unable to get speeds over this connection (tested with iperf) of anything over 600Kb or so down from the main office (traffic will pretty much always be from the main office to the remote office) Whilst I realise that there is an overhead and I'm never going to get the "full" bandwidth available over this VPN, I'd like to think that there's something I should be looking at that may help improve it. I've tried using the DrayTek's built-in "VPN Trunking" features which are supposed to load-balance connections, but this doesn't seem to improve matters much. I guess my question is - is this the kind of performance I should expect from this kind of setup and I'll just have to live with it, or should I be able to squeeze something more out of it through some VPN magic?

  Read the article

• Manual TRIM Windows 7 on OCZ VERTEX 2 SATA II 2.5" SSD

  - by INTPnerd

  I have an OCZ VERTEX 2 SATA II 2.5" SSD with Windows 7 Professional installed on it. I am pretty sure TRIM is not working because my motherboard is the Asus M2N-SLI (not the Deluxe model) which does not support AHCI mode for the drive. Is there a utility that is compatible with this drive that I could possibly run once a day that would do something similar to a manual TRIM in order to keep the drive performance up? I could not find one specifically for this drive on the OCZ website. I did find a User-Initiated Garbage Collection wiper tool, but it is for a Vertex drive not Vertex 2. I tried to run it, but it said that wiper could not be run for all the drives on this system.

  Read the article

• Graphic Setup tune-up checklist

  - by Click Ok

  I was trying to play the game Warzone 2100 and the games runs fine, with nice speed, but the screen stays with a horizontal lines "flickering"... My PC have a integrated GeForce Go 6100 vga. Ok, not a powerfull vga, but it's not the end of the world to run a "simple" game like this (compared with another games that ask you send your eyes to purchase a expensive vga). So, I think that the problem can be of the configuration of my machine. I use it in first instance for programming jobs, so I underpay attention to video setup. I would like about a checklist to know if my PC is "ready" to games. By example, I know that I need: Lastest vga drivers Updated DirectX and OpenGL What you suggest? There is too some good programs to test performance and suggests improvements in the system? Thank you! PS: I'm using Windows 7

  Read the article

• Using a CF card as an IDE HDD

  - by dartacus

  I have an old Sony laptop (Vaio TR1-MP) that I like. The HDD has died and since it's a hard-to-find 1.8" IDE hard drive I'm considering buying one of those little CF card adaptors and a 16gb CF card. The total cost of that is about £30 and replacement HDDs for this model are far pricier. Has anyone replaced their HDD with a CF card in this way, and, crucially, is the performance utterly horrible afterwards? ;-) I've seen a couple of threads which hint it's possible but the advice eventually given was just to buy a SSD, but I'm not even sure if its possible to get a 1.8" SSD with an IDE connector that'll fit my laptop. (I freely admit that the most sensible thing to do would be to bin it and just buy a cheap netbook which would be smaller, faster and lighter than the sony, but it does have a very nice widescreen display and dammit I just like it !) Thanks, G

  Read the article

• What is the Optimal Server Configuration for Split-Path Testing?

  - by doug

  I am far from an expert on Apache or any server for that matter, so i apologize if this question is poorly worded, which it likely is. We have always relied on a vendor for split-path testing (aka "AB Testing"). If you're not familiar with that term, it's a form of marketing research in which you slightly modify one of your web pages (usually one nearest the point of conversion), say for instance, by changing the position of the "Buy Now" button or its color/contrast/texture, then serving one of those two pages to a given user based on random selection. By doing split-path testing ourselves, I suspect we can do it far more cheaply and increase cycle times as well. What is the optimal set-up for these tests? "Optimal" is based on the following criteria: how quickly/easily new tests can be set-up and put online; and minimal disruption to overall site performance

  Read the article

• Upgrade no raid server to raid

  - by AZee

  I have just learned that our PDC has a single drive with 2 partitions. I also know that this drive has bad blocks as recorded in the event log. What I would like to do is to convert this to a RAID solution with a nice balance between economy and performance. I will admit that I have only configured servers with RAID from scratch, and have no experience upgrading an existing system into a RAID system. In fact, I'm not sure it is even possible. Since this is the PDC for 350+ workstations downtime is important. I'd like to hear from other System Administators how they would tackle this and their recommendations for all devices. At this time it seems to me that I can replace the existing drive and then restore from backup or install a controller, drives, configure the RAID an basically start from scratch. Thank you for taking your time. ~AZee

  Read the article

• slow disk writes between host and guest

  - by Jure1873

  I've got a ubuntu (server kernel) on a amd x4, 4gb ram, 2x seagate sata 1 tb disks for testing virtual machines and the write performance is very slow. The two disks are in a software raid1 array, one small boot ext3 partition, 10gb system partition and the rest is a xfs partition (about 980) gb for data (virtual machines). If I'm copying files from the virtual machine to the host with rsync or scp the copy frequently stalls or goes at about 1mb/s. What's wrong? I've tried disabling barriers on xfs, increased logbufs, allocsize, but it seems nothing helps. The strange thing is that await (for example during copying) for sda is usually under 100, while for sdb is around 400. Any ideas on what could be wrong / what could I do to improve this setup?

  Read the article

• Missing 16:10 resolutions with Nvidia drivers (Can't add resolutions)

  - by Wuinny

  Hello, I have a laptop with a Nvidia 9650M GT and used the drivers that Seven brought me. It works fine but Metro 2033 tells me that i have to upgrade my drivers to play the game. So i did it. But since i did a clean install of the new Nvidia drivers, i just have 1440*900 or 4:3 resolutions. I usually played with 1280*800 or 1184*740 (for performance issue) With the "old" drivers i was able to create custom resolution (1184*740) in Nvidia control panel but now when i try it tells me that "my monitor cannot support this resolution". When i insist, it works but soon as i shut down my computer i have to recreate it.. Do anyone have a fix ? Thank you

  Read the article

• Virtualbox, merging snapshots and base disk

  - by Henrik

  Hi, I have a virtual machine with about 30 snapshots in branches. The current development path is 22 snapshots plus the base disk. The amount of files is seemingly having an impact now on IO and the dev laptop I'm using (don't know if it is host disk performance issues with the 140GB total size over a lot of fragments, or just the fact that it is hitting sectors distributed across a lot of files). I would like to merge the current development branch of snapshots together with the base disk, but I am unsure if the following command would produce the correct outcome. I am not able to boot this disk after the procedure completes (5-6 hours). vboxmanage clonehd "C:\VPC-Storage\.VirtualBox\Machines\CRM\Snapshots\{245b27ac-e658-470a-b978-8e62137c33b1}.vhd" "E:\crm-20100624.vhd" --format VHD --type normal Could anyone confirm if this is the correct approach or not?

  Read the article

• Cached css/javascript files on Sun Java System Web Server

  - by Derp

  I'm doing front-end web development in a Solaris 10 / Sun Java System Web Server 7.0U2 environment. I have noticed that changes to static css or javascript files often do not take effect immediately, whereas changes to static html files always do. My best guess is that a default setting in the web server causes it to cache certain file types in order to provide reasonable performance out of the box. I don't have the admin server running--I'll need to edit the config files by hand. What change(s) can I make so that all of my css and javascript edits take effect immediately? Thanks!

  Read the article

• smartOS HPC config suggestion

  - by Andrew B.

  I'm configuring a brand new HPC server and am interested in using SmartOS because of it's virtualization control and zfs features. Does this configuration make sense for a SmartOS HPC, or would you recommend an alternative? System Specs: 2x 8-core xeon 384 GB RAM 30 TB HDs with 2x512GB SSDs Uses: - zfs for serving data to different vms, and over the network; 1 SSD for L2ARC and 1 for ZIL - typically 1-2 ubuntu instances running R and custom C/C++ code My biggest concerns as a newbie to SmartOS and ZFS are: (1) will I get near-metal performance from ubuntu running on SmartOS if it is the only active vm? (2) how do I serve data from the global zfs pool to the containers and other network devices?

  Read the article

• Linux IO scheduler on databases with RAID

  - by Raghu

  Hi, I have a linux database(MySQL) server(Dell 2950) with a 6-disk RAID 10. The default IO scheduler on it is CFQ. However, from what I have read and heard, there is no need for a scheduler like CFQ when reordering/scheduling is also done by underlying RAID controller; on the contrary since it does not account underlying RAID configuration into account performance may actually degrade with CFQ. The primary concern is to reduce CPU usage and improve throughput. Also, I have seen recommendations of using noop/deadline IO scheduler for databases primarily because of the nature of their R/W access.

  Read the article

• Evaluate a vendor laptop before deployment to user?

  - by NetWarrior

  I get numerous requests from executives and users for new smaller laptops for travel purposes. Most of my evaluation is based upon whether or not it can run certain applications. Mainly lotus notes, office, and video. Most of the laptops include windows 7 OS, and are fully loaded with ram, a high-end processor and a integrated graphics card. My boss whats me to document the usefulness of the laptop and performance. I'm just a little confused on how to setup a document that can be used by members of the IT department for future evaluations.

  Read the article

• How to get the spec of a machine on Linux?

  - by machinePurchaser

  I am interested in getting the spec of a machine, because I am thinking getting a similar server. What I am mostly interested in knowing is the number of cores / CPUs / etc., the amount of memory, the speed of the CPUs, the CPU cache size, and any other detail which is important for performance. My question is two-fold: Which parameters should I be interested in other than the ones I specified above? Is there an easy way to read them off the machine in Linux? cat /proc/cpuinfo reveals a lot about the CPUs, for example... What about memory (would rather not rely on top), etc?

  Read the article

• Linux RAID0 - relocating member disk

  - by qdot

  I've got an issue I would rather handle with the array online - I am using RAID0 for temporary video storage - data that is low-cost to restore, but that is used frequently. The software array looks like this: md1 : active raid0 sdb1[2] sdc1[3] sdd1[0] sde1[1] 1953487616 blocks 64k chunks I have another partition (sda1) in this system, that I want to use to replace sdc1 (The drives are of varying age, and sdc1 is definitely the slowest one, limiting the entire array's sequential read performance to only 300MB/s). Is there a way to migrate the data from sdc1 to sda1 while the array is still online?

  Read the article

• Pages partially load on rapid refresh

  - by user101570

  I recently set up a VPS slice with 256MB to run a LAMP stack (Ubuntu 11.04, Apache2, Mysql, PHP5). So far I'm only running a simple Wordpress site on an IP-based virtual host I set up. The performance is excellent, but I've noticed that if I send multiple HTTP requests from the same IP in a short time period, only partial pages are rendered. Then if I wait a bit and refresh the page, the entire page loads again. I noticed this behaviour when accessing the site from two browsers from my office desktop, but it also presents itself if I quickly navigate the site from a single browser (any browser). I'm guessing this is an Apache phenomenon, as the pages are rendered correctly except under the conditions above, but perhaps I'm wrong here. Could it be my hosting company with some kind of DOS protection in place? As a relative Linux/server noob, I'd really appreciate any insight into what settings in Apache could explain this behaviour, and how I might go about changing it.

  Read the article

< Previous Page | 406 407 408 409 410 411 412 413 414 415 416 417  | Next Page >