Search Results

Search found 28439 results on 1138 pages for 'wingman20 10'.

Page 411/1138 | < Previous Page | 407 408 409 410 411 412 413 414 415 416 417 418  | Next Page >

• PowerConnect 3548p SNTP and web interface not working

  - by Force Flow

  I have been unable to get SNTP and access to the web interface working properly on a Dell PowerConnect 3548p. In the logs, this message appears over and over again: 04-Jan-2000 20:19:29 :%MNGINF-W-ACL: Management ACL drop packet received on interface Vlan 172 from 172.17.0.3 to 172.18.0.10 protocol 17 service Snmp 172 is the management vlan. 172.17.0.3 is the DNS server 172.18.0.10 is the switch's IP address. The DNS server and the switch are located on different subnets and separated by routers. I am unable to access the web interface of the switch from the 172.17.x.x subnet. I can only access the web interface of the switch if I am accessing it from the 172.18.x.x subnet. There is also a managed linksys switch on the 172.18.x.x subnet on the 172 vlan, which has no problem with SNTP. I can also access it from the 172.17.x.x network. So, it stands to reason that this is not a firewall or routing issue, but with the 3548p switch. I suspect the issue is with management permissions/ACLs on the 3348p switch, but that's about as much as I've been able to determine so far. Any ideas?

  Read the article

• How to route between 2 networks with a server with 2 network cards?

  - by LumenAlbum

  This is the first time I am faced with routing and it seems I have hit a dead end. I have the following scenario: client1: 192.168.1.10 255.255.255.0 gateway: 192.168.1.100 DNS server: 192.168.1.100 client2: 192.168.1.20 255.255.255.0 gateway: 192.168.1.100 DNS server: 192.168.1.100 server (Windows Server 2008 R2 with enabled RAS & Routing Services) network card 1 (connected to a switch along with the clients) 192.168.1.100 255.255.255.0 DNS server: 127.0.0.1 network card 2 (connected to the router) 192.168.2.100 255.255.255.0 gateway: 192.168.2.1 DNS server: 127.0.0.1 (DNS forwarding to 192.168.2.1) ISP router (with connection to internet) 192.168.2.1 Now in this scenario I have tried to route traffic from the 192.168.1.0/24 network with the clients to the 192.168.2.0/24 network with the routers to connect them to the internet. However, no matter what I do I get no positive ping to the router 192.168.2.1. Ping from 192.168.168.1.10 to 192.168.1.20: Success to 192.168.1.100: Success to 192.168.2.100: Success to 192.168.2.1: not reachable The routing table contains the 2 routes 192.168.1.0 and 192.168.2.0 as directly connected. Does anyone know where the routing fails? I have searched different forums but mostly found nothing relevant. One post however pointed out that in a similar situation the problem was that the router doesn't know the way back and the internet router would need a static route back to the first router. If that really is the case, I take it there is no solution with my equipment, because the standart ISP router doesn't allow to set any static routes.

  Read the article

• Making "default saved" work with GRUB2...?

  - by baltusaj

  I just installed Moblin Operating System. It's using GRUB2. On my Ubuntu 8.04 GRUB 0.97 was being used in which i was using the default saved option comfortably. I found that with GRUB2 i should not edit /boot/grub/menu.lst directly but I did :) because my Moblin does not contain any /etc/default/grub where they say I should do the modification I want. So what I did is as following which did not work: default=saved timeout=1 #splashimage=(hd0,0)/boot/grub/splash.xpm.gz #hiddenmenu #silent title Moblin (2.6.31.5-10.1.moblin2-netbook) root (hd0,0) kernel /boot/vmlinuz-2.6.31.5-10.1.moblin2-netbook ro root=/dev/sda1 vga=current savedefault=1 title Pathetic Windows rootnoverify (hd0,1) chainloader +1 savedefault=0 By doing so I should have automatically switch between Moblin and Window at each boot but it's not working. Almost all the troubleshooters on internet are saying that I should enable the DEFAULT=save option in /etc/default/grub but I am unable to find this file. Any idea what else should I do? Thanks a lot Update: I used the equal to sign because by default my menu.lst had an entry as default=0. However, default 0, is also working fine. Moreover the menu.lst, i have is actually a symbolic link to ./grub.conf. I have also noticed that grub-intall and grub-set-default commands are not working.

  Read the article

• Solaris Mysql Failure and Unable to Restart

  - by Iscariot

  Environment: Solaris 10 This mysql server has been up and running for 6 months now. Today all of a sudden it crashed. When typing 'mysql' as user it gives the error MYSQL" Error 2002 (HY000): Can't Connect to Local MySQL server though socket '/tmp/mysql.sock' when typing mysql as root it says mysql: not found. The server try to open mysql, it stays open for 9-10 seconds and restarts the process. Below are the application logs. Application-database-mysql_mysql-csk.log [ May 30 22:37:52 Enabled. ] [ May 30 22:37:58 Rereading configuration. ] [ May 30 22:37:59 Executing start method ("/opt/coolstack/lib/svc/method/svc-cskmysql start") ] /opt/coolstack/mysql/bin/mysqld_safe --user=mysql --datadir=/dbpool1/data --pid-file=/dbpool1/data/database.soliaonline.com.pid [ May 30 22:37:59 Method "start" exited with status 0 ] [ May 30 22:38:13 Stopping because all processes in service exited. ] [ May 30 22:38:13 Executing stop method ("/opt/coolstack/lib/svc/method/svc-cskmysql stop") ] [ May 30 22:38:13 Method "stop" exited with status 0 ] [ May 30 22:38:13 Executing start method ("/opt/coolstack/lib/svc/method/svc-cskmysql start") ] /opt/coolstack/mysql/bin/mysqld_safe --user=mysql --datadir=/dbpool1/data --pid-file=/dbpool1/data/database.soliaonline.com.pid [ May 30 22:38:13 Method "start" exited with status 0 ] [ May 30 22:38:25 Stopping because all processes in service exited. ] [ May 30 22:38:25 Executing stop method ("/opt/coolstack/lib/svc/method/svc-cskmysql stop") ] [ May 30 22:38:25 Method "stop" exited with status 0 ] I am hoping someone might have run into this before and might know how to fix it.

  Read the article

• AFP/SSH stopped working on OS X Server

  - by churnd

  I have 3 Mac OS X servers all bound to AD, all configured in the Golden Triangle setup. All 3 are completely separate from each other in terms of services, but all reside on the same internal network and are all bound to the same Active Directory domain. Two are 10.5.x (latest updates) and one is 10.6.3. Last weekend, all 3 simultaneously stopped allowing Active Directory users access to certain services, specifically AFP & SSH. SMB still works fine on all 3. I asked the AD admin if anything changed, and he said "Yes, we made a change to user accounts to toughen up security", and suggested I use [email protected] instead of just username. This still didn't work. I have completely removed one of my servers from AD, and re-joined, but this didn't work either. I can do kinit from command line and get a Kerberos ticket. sudo klist -ke shows all services are configured to use the correct Kerberos principles. I have been scavenging the logs for any useful info. The AFP log just shows that I'm connecting and disconnecting. The DirectoryService.log shows stuff about misconfigured Kerberos hashes, but my research is showing that's not uncommon. /var/log/system.log isn't showing anything useful that I can see. I'm not sure where to go from here. Any help/ideas appreciated.

  Read the article

• Postfix additional transports - is it working?

  - by threecheeseopera

  I have enabled two additional transports in my postfix config to deal with recipient domains that demand connection limiting, per the instructions here at serverfault. However, I have no idea if this is working or not; in fact, I think it is not working, due to the send speeds I am seeing in the logs. How might I determine if my additional transports are working? If they aren't, do you have any tips on figuring out why? And, do you have any comments on my particular configuration? (am I a bucket of fail?) I have enabled the additional transports in master.cf: smtp inet n - - - - smtpd careful unix - - n - 10 smtp -o smtp_connect_timeout=5 -o smtp_helo_timeout=5 cautious unix - - n - - smtp -o smtp_connect_timeout=5 -o smtp_helo_timeout=5 I have set up the transport mapping file /etc/postfix/transport: hotmail.com cautious: yahoo.com careful: gmail.com cautious: earthlink.net cautious: msn.com cautious: live.com cautious: aol.com careful: I have set up the transport mapping and some connection-limiting settings in main.cf: transport_maps = hash:/etc/postfix/transport careful_initial_destination_concurrency = 5 careful_destination_concurrency_limit = 10 cautious_destination_concurrency_limit = 50 Finally, I have run converted the transport file to a db per the postfix docs: #> postmap /etc/postfix/transport And then restarted postfix. I do see my transport_maps setting when I run postconf, but I do not see any of the transport-specific settings ('careful_xxx_yyy_zzz'). Also the mail logs do not appear to be different in any way to what they were previously. Thanks!!!

  Read the article

• Fedora 15: em1 recently dissapeared and hostapd no longer serves internet to wirelessly connected devices

  - by Daniel K

  I have a laptop running hostapd, phpd, and mysql. This laptop uses an Ethernet connection to connect to the internet and acts as a wireless access point for my workplace's wifi devices. After installing some software and reconnecting my Ethernet elsewhere, my "em1" device is no longer present and wirelessly connected devices can no longer reach the internet. The software I recently installed is: pptp, pptpd, and updated some fedora libraries. I have also recently moved my desk and laptop to another location and thus had to reconnect the Ethernet elsewhere. Wifi devices no longer have access to the internet. Wirelessly connected devices are able to successfully log into the laptop, showing full strength, correct SSID, and uses the proper password. However, when I tried to connect to a site like google, the request times out. The device "em1" also no longer appears on my machine. Running: # ifup em1 will give me the following output: ERROR : [/etc/sysconfig/network-scripts/ifup-eth] Device em1 does not seem to be present, delaying initialization. And running: # dhclient em1 has the following output: Cannot find device "em1" When I run # dmesg|grep renamed, I get the following: renamed network interface eth0 to p4p1. I've tried to connect to the internet through p4p1 directly from the laptop and was successful. However, my wireless devices connected to my laptop are not able to connect to the internet. I have uninstalled pptp and pptpd using # yum erase ... but the problem still persists. To install pptp I used: # yum install pptp To install pptpd I did the following: # rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc15/pptp-release-current.noarch.rpm # yum install pptpd To update my fedora libraries I used: # yum check-update # yum update EDIT: Running # route produces the following results: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.11.200.1 0.0.0.0 UG 0 0 0 p4p1 10.11.200.0 * 255.255.252.0 U 0 0 0 p4p1 172.16.100.0 * 255.255.255.0 U 0 0 0 wlan0

  Read the article

• Is this way of using Excel 2007 Pivot table for BI scalable ?

  - by Sim

  Hi all, Background: We need to consolidate sales data across the country to do analysis Our Internet connection/IT expertise/IT investment is not quite strong, therefore full BI solution is out of question I tried several SaaS BI solution (GoodData, ZohoReports) and while they're good, they seem not to fully support what we need We're looking at 'bout 2 millions record for every 2 months My current approach Our (10) sites currently gathers data from all their branches and consolidate them into 1 Excel file with Pivot table and embed source data In HQ, I will request 10 sites to send back those Excel files periodically We will import those Excel to our MSSQL server There will be a master Excel file, that will also have the same pivot table (as those came from site Excel file), and datasource is the MSSQL server More details For testing, I currently use MSSQL 2008 Express on my laptop So far, I imported our transactions for the past 2 months and there are 2 millions+ row in 1 table in MSSQL (we just use 1 table, corresponding to our common pivot table structure). DB size is ~ 600 MB In the master Excel file, if not including the source data, it's just < 10MB. Including the source data will increase the size to 60 MB (so I supposed Office 2007 automatically zip the data ?) I try using the Pivot (drag-and-drop fields) and the performance so far is OK (my laptop specs: C2D T7200, 3GB RAM, Windows XP) So my question is : If we're looking at full year transaction (roughly 15 millions rows in MSSQL 2008 Express, 3.6 GB in size), is there any issue with that 15 million rows in 1 table in SQL Express ? Is there any performance issue with the pivot table at that time ? Can it still embed the source data ? (I google-ed but didn't find the maximum size of source data Excel 2007 can embed) Any other suggestions on how we can better do this ? Given that we can't afford the full BI solution, any light-weight/budget/SaaS BI that you can recommend ? Thanks

  Read the article

• Adding 2nd DC to the domain from a different subnet over VPN.

  - by EagerToLearn

  I'm in the process of adding a second DC to our domain and just want to make sure I have all the steps right before proceeding. Info: DC1 is 2008 R2 Standard. DC2 is 2008 R2 Standard. Network1 is 192.168.39.x/24 Network2 is 10.0.0.x/24 VPN is Sonicwall. The 2 DC's will be at two different sites, but the networks are connected by hardware VPN. (Sonicwall). The main DC server will be on the 192.168.39.0/24 network. The 2nd DC will be on 10.0.0.0/24. Here are the steps I plan to take; please let me know if I'm missing anything. Part 1: AD Sites and Services on DC1, create a new site and subnet for DC2. (Or should I create a new one for both?) (Can I use the default IPSiteLink and not change anything in there other than refresh timer?) Part 2: Point the DNS of DC2 to DC1. Run /forestprep and /domainprep (on both, or just DC1?). Dcpromo and select "Additional Domain Controller for Existing Domain". Then continue with normal steps with default locations for databases. EDIT: Didn't realize this was like reddit and required two skipped lines to skip one :P EDIT 2: When DCPromo-ing DC2, do I need to have "Append primary and connection specific DNS" and "Append parent suffixes of the primary DNS suffix" checked?

  Read the article

• Unable to ssh to a Linux VM after a day

  - by jogabonito

  I have a machine running 4 VMs on it. There is one Fedora VM which is causing me some trouble. The IPs of the VMs are something like 10.100.100.* I have a Windows PC which is in the same network. It has an IP 10.100.25.77. When I reboot the Fedora VM, I am able to ping it from my Windows PC as well as use putty to ssh to it. The next day, I cant ping it or ssh from my Windows PC. However I can ping and ssh to the other VMs on the machine. If I ssh to one of the other VMs, I can ping and ssh to the Fedora VM. Next if I restart it, things get back to normal and I can access it without any issues. The IP of the VM doesn't change after rebooting and it is statically assigned I would like to know what is causing this and how to get it fixed. As a last resort, I am thinking of running a cron job to restart the VM every night, it is not a critical server, but will be generally used occasionally in the day time.

  Read the article

• Network connection keeps dropping - bad hardware?

  - by Bill Sambrone

  Hello all, I've into a bit of a wall with a client of mine. In an office of 20 people, he is the only one who experiences broken connections to his mapped network drives. I have everyone set up with about 6 mapped drives, all pointing to the same server (no DFS), and everyone else can access them lightning fast. The environment consists of a mix of Windows 7 and XP machines, all 32-bit. The server holding the data everyone is mapping to is running on Server 2008 R2, and is a domain controller. We recently swapped out their old 10/100 switch for a shiny new Dell PowerConnect gigabit switch. We have also replaced an old dying Sonicwall with a shiny new one. Everything is running on an ESX host except for the DC, where everyone is getting data from. In my client's office, we have done the following: Swapped out his computer (Win7 and XP box) Swapped out the desktop switch in his office Removed the desktop switch in his office Changed out the network cable going to the wall Ran 'net config server /autodisconnect:-1' on the server Disabled remote differential compression on his current Win7 box When we swapped out his network cable, everything seemed fine for about 4 days. Normally I would get a phone call a couple times per day letting me know that Outlook has crashed (there is a 9GB PST living on the server he is always connected to), or that his software he is running from his L drive has crashed. I almost thought I had this solved, but after we rebooted the DC the other night he all of a sudden couldn't stay connected to his mapped network drives for more than 10 minutes. When I ran 'net use' from the command prompt, it listed all the network drives where were randomly in a state of 'OK', 'Disconnected', or 'Reconnecting'. What else should I try? Maybe there is bad wiring in the wall, patch panel, or a bad port in the new switch I have in the server room?

  Read the article

• WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

  - by Elton Carvalho

  I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

  Read the article

• Intel Ethernet Bottlenecking Internet?

  - by Donald Darma

  I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

  Read the article

• Windows Server 2008 R2 Virtual Network Setup

  - by jpearl01

  Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

  Read the article

• Wake a Mac display from sleep via SSH

  - by MaxGabriel

  I'm using Jenkins as a CI server, where I'm SSHing into an iMac running OS X Mountain Lion (10.8.4) to run some UIAutomation integrations tests on an iOS app. The iMac actually sits 10 ft from me (but across a table) so I'm able to see the screen. However, the tests don't wake up the display, so I often can't see them. Is there a way to wake up the display from the terminal once Jenkins has SSHed in? So far I have tried using Applescript to press an arrow key, and using the Wake Assist application. I also tried setting the wake schedule to be the current date. Finally, I tried using the caffeinate command: caffeinate -t 300 &. The computer's "Wake for Wi-Fi access" checkbox is enabled. So far my best workaround is to just set the iMac to stay awake for atleast 3 hours. However, it'd be nice to keep normal sleep behavior, as I hypothesize that the screen waking from sleep would alert me visually that the integration tests are running. It's also significantly cooler :)

  Read the article

• Gigabit LAN not working on ASUS M2N-MX

  - by chmod

  Today I replace my FastEthernet switch with a newly bought gigabit switch (DGS-1008A). All computers in my house are displaying that the connection speed is 1 Gbps except for one. The computer that is not working is an ASUS M2N-MX which contain an onboard gigabit NIC. See ASUS link for confirmation http://www.asus.com/Motherboards/AMD_AM2/M2NMX/ Here are some info of the machine OS: Windows 7 Ultimate SP1 64bit BIOS version: 1004 (latest) Driver: installed via Windows update (latest from Windows update) Windows Update: fully updated The machine is reformatted 3 days ago, so it's pretty clean, no junk, no virus, etc Cable: Amp CAT5E 5 meters In device manager, the name of the NIC is "NVIDIA nForce 10/100/1000 Mbps Ethernet" What I have try: I did try to install the driver provided in ASUS website, but there isn't any for Windows 7 64 or Vista 64. I did try to install the latest nForce340/6100, downloaded from Nvidia website. However, the LAN driver refuse to install, it complain that I already have the best driver installed. I looking in the property -- advance tab -- Speed/duplex settings, in an attempt to force it to run at 1000Mbps, but there is no 1000Mbps choice, only 10 and 100Mpbs. I change the CAT5E cable (use one from another computer that is running gigabit without problem) Anyone have this issue or know how to solve it? Thanks

  Read the article

• Using udev to create a character device based on a driver being loaded

  - by SteveCB

  I'm in the process of setting up RAID monitoring for a number of Dell servers that use the PERC 6i integrated card. We're using Nagios at present and the check_megasasctl plugin seems to fit the bill. However, the plugin relies upon the existence of: /dev/megaraid_sas_ioctl_node This device node doesn't exist by default, you have to create it by hand using something like: mknod /dev/megaraid_sas_ioctl_node c 253 0 Now, to make the existence of this device node persistent across reboots, I thought I could write a udev rule, but as usual, I'm missing something. I thought I could create a file such as /etc/udev/rules.d/10-local/rules that contained: DRIVER=="megasas" NAME="megaraid_sas_ioctl_node" MODE="0600" But this doesn't work - no device node after a reboot. Dmesg output indicates the megasas driver is loaded and functional: megasas: 00.00.04.01-RH1 Thu July 10 09:41:51 PST 2008 megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0 megasas: FW now in Ready state Further, I don't see any means to instruct udev on which type of device node to create: character or block. I suspect I'm failing to understand exactly how udev is meant to work. I realise I could just cheat and run MegaCLI in /etc/rc.local, redirecting output to /dev/null; it creates the megaraid_sas_ioctl_node device node as part of its execution. I just thought using udev rules would be a) cleaner and b) a useful learning exercise. Perhaps I should just dump the above mknod command in /etc/rc.local... So how do I get udev to create the /dev/megaraid_sas_ioctl_node device node based on the presence of the megasas driver? Cheers Steve

  Read the article

• CentOS 5.7 issues with iptables

  - by Corey Whitaker

  I'm trying to set up IPTables on a new CentOS server. This server will function as an FTP server that I need to be accessible from the outside, however, I want to lock down SSH to only accept internal IP connections. I need to allow SSH for 10.0.0.0/8 and 172.16.132.0/24. Below I've posted my /etc/sysconfig/iptables file. Whenever I apply this, I essentially lock myself out and I have to access it via console using Vsphere. Can somebody show me what I'm doing wrong? I'm connecting from my laptop with an IP of 172.16.132.226. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [115:15604] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp -m icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p esp -j ACCEPT -A RH-Firewall-1-INPUT -p ah -j ACCEPT -A RH-Firewall-1-INPUT -d 224.0.0.251 -p udp -m udp --dport 5353 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A RH-Firewall-1-INPUT -s 10.0.0.0/8 -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -s 172.16.132.0/24 -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 20 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 21 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT

  Read the article

• Defining Virtual and Real User Directories with Dovecot & Postfix

  - by blankabout

  Following a wobble described in this question we now have virtual and real users authenticating with Dovecot, the problem now is that the real users (who have been on the system for years) can no longer access their mail. I'm guessing that it is because Dovecot is configured to point to the virtual mailboxes but not the real mail boxes. These are snippets from the config files: /etc/dovecot/dovecot.conf !include conf.d/*.conf /etc/dovecot/conf.d/10-auth.cong passdb { driver = passwd-file # Path for passwd-file. Also set the default password scheme. args = scheme=cram-md5 /etc/cram-md5.pwd } userdb { driver=static #args = mail_uid=dovecot mail_gid=dovecot /etc/dovecot/userdb args = uid=vmail gid=vmail home=/var/spool/vhosts/%d/%n /etc/dovecot/userdb } [email protected]:::::/var/spool/vhosts/virtualdomain.com/:/bin/false:: We think the problem is that the Dovecot file 10-auth.conf does not contain a method of accessing the mailboxes for the real users. We have looked around on this site, dovecot.org and done the usual googling but cannot find anywhere that describes how to set up virtual users on alongside legacy real users. Any help would be appreciated, especially by our real users who would like the contents of their inboxes to be available! If any further config is required, please let me know.

  Read the article

• SSD suddenly full

  - by Daniel

  Today the hard drive of our server was suddenly full. The disk usage always stayed around 50 % in the weeks and months before (old data is regularly expunged from the server). I deleted 10 GB of files in /tmp, which strangely freed 51 GB. Here is what I did: root@***:~# df -h Dateisystem Size Used Avail Use% Eingehängt auf /dev/sda3 139G 137G 0 100% / tmpfs 3,9G 0 3,9G 0% /lib/init/rw udev 3,9G 116K 3,9G 1% /dev tmpfs 3,9G 0 3,9G 0% /dev/shm /dev/sda1 985M 25M 910M 3% /boot root@***:/var# du -hs * 3,3M backups 438M cache 9,4G lib 4,0K local 12K lock 76M log 24K mail 4,0K opt 88K run 184K spool 10G tmp 12K www root@***:/var/tmp# find -type f -print0 | xargs -0 rm root@***:/var/tmp# df -h Dateisystem Size Used Avail Use% Eingehängt auf /dev/sda3 139G 81G 51G 62% / tmpfs 3,9G 0 3,9G 0% /lib/init/rw udev 3,9G 116K 3,9G 1% /dev tmpfs 3,9G 0 3,9G 0% /dev/shm /dev/sda1 985M 25M 910M 3% /boot Any explanation as to why deleting 10 GB in /tmp gave me back 51 GB on the disk? Could this point to an SSD failure? Are there any tools for Debian to test SSD health? I already have checked syslog. The first entry relating to this incidient is a mysql message: 1:22:02 [ERROR] /usr/sbin/mysqld: Disk is full writing... So I have absolutely no idea what caused this.

  Read the article

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• How to completely disable IPv6 for loopback interface on RHEL 5.6

  - by Marc D

  I've done lots of research on how to disable IPv6 on RedHat Linux and I have it almost completely disabled. However the loopback interface is still getting an inet6 loopback address (::1/128). I can't find where IPV6 is still enabled for loopback. To disable IPV6 I added the following settings to /etc/sysctl.conf: net.ipv6.conf.default.disable_ipv6=1 net.ipv6.conf.all.disable_ipv6=1 And also added the following line to /etc/sysconfig/network: NETWORKING_IPV6=no After rebooting, the inet6 address is gone from my physical interface (eth0), but is still there for lo: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:50:56:xx:xx:xx brd ff:ff:ff:ff:ff:ff inet 10.x.x.x/21 brd 10.x.x.x scope global eth0 If I manually remove the IPV6 address from loopback and then bounce the interface, it comes back: # ip addr del ::1/128 dev lo # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo # ip link set lo down # ip link set lo up # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever I believe IPV6 should be disabled at the kernel level as confirmed by sysctl: # sysctl net.ipv6.conf.lo.disable_ipv6 net.ipv6.conf.lo.disable_ipv6 = 1 Any ideas on what else would cause the loopback interface to get an IPV6 address?

  Read the article

• VPN into multiple LAN Subnets

  - by Rain

  I need to figure out a way to allow access to two LAN subnets on a SonicWall NSA 220 through the built-in SonicWall GlobalVPN server. I've Googled and tried everything I can think of, but nothing has worked. The SonicWall NSA management web interface is also very unorganized; I'm probably missing something simple/obvious. There are two networks, called Network A and Network B for simplicity, with two different subnets. A SonicWall NSA 220 is the router/firewall/DHCP Server for Network A, which is plugged into the X2 port. Some other router is the router/firewall/DHCP server for Network B. Both of these networks need to be managed through a VPN connection. I setup the X3 interface on the SonicWall to have a static IP in the Network B subnet and plugged it in. Network A and Network B should not be able to access each other, which appears the be the default configuration. I then configured and enabled VPN. The SonicWall currently has the X1 interface setup with a subnet of 192.168.1.0/24 with a DHCP Server enabled, although it is not plugged in. When I VPN into the SonicWall, I get an IP address supplied by the DHCP Server on the X1 interface and I can access Network A remotely although I do not have access to Network B. How can I allow access to both Network A and Network B to VPN clients although keep devices on Network B from accessing Network A and vice-versa. Is there some way to create a VPN-only subnet (something like 10.100.0.0/24) on the SonicWall that can access Network A and Network B without changing the current network configuration or allowing devices on both netorks "see" each other? How would I go about setting this up? Diagram of the network: (Hopefully this kind of helps) WAN1 WAN2 | | [ SonicWall NSA 220 ]-(X3)-----------------[ Router 2 ] | | (X2) 192.168.2.0/24 10.1.1.0/24 Any help would be greatly appriciated!

  Read the article

• esx5 debian VM vlan setup

  - by Kstro21

  i have a server with ESX5, have a switch with about 20 vlans, this is how setup the trunk port interface GigabitEthernet0/1/1 description ToOper port link-type trunk undo port trunk allow-pass vlan 1 port trunk allow-pass vlan 2 to 14 stp disable ntdp enable ndp enable bpdu enable then, i created a standar switch(sw1) using the vSphere Client, the VLAN ID is set to All (4095), i also created a VM with Debian 6, with a NIC connected to sw1, now, i want to configure this NIC for a selected group of vlans auto vlan10 iface vlan10 inet static address 11.10.1.0 netmask 255.255.255.224 mtu 1500 vlan_raw_device eth0 auto vlan14 iface vlan14 inet static address 11.10.1.65 netmask 255.255.255.248 mtu 1500 vlan_raw_device eth0 so, when i restart the network using /etc/init.d/networking restart, i got this error Reconfiguring network interfaces...SIOCSIFADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFMTU: No such device vlan14: ERROR while getting interface flags: No such device Failed to bring up vlan14. done. this is just part of the error, so, my questions is: is this possible?, i mean, what i'm trying to achieve using ESX Virtual Machines, VLANS, etc is this a Debian problem? can be solved? i've read about a file named z25_persistent-net.rules in Debian but it doesn't exist in my installation. in the In the vSphere Networking for ESX5 guide, you can read: If you enter 0 or leave the option blank, the port group can see only untagged (non-VLAN) traffic. If you enter 4095, the port group can see traffic on any VLAN while leaving the VLAN tags intact. So, in theory, it should work, right? Hope you can help me up with this one Thanks

  Read the article

• What is wrong with those crontabs?

  - by Guillaume Boudreau

  I want my projectors to Power On before the mall opens, and Power Off when the mall closes. So I created crontab entries (that I placed in /etc/cron.d/mall), but today (Thu Nov 22 18:58:29 EST 2012 is the current date on that server), the power-off.sh script got executed at 17:20 (see syslog excerpt below). Being Thu, Nov. 22, I would have expected the power-off.sh script to be executed at 21:20, per the 4th crontab line below. Why did power-off.sh execute at 17:20? What is wrong with my crontab entries? Content of /etc/cron.d/mall: 40 9 22-30 Nov Mon-Sat myuser /usr/local/projectors/power-on.sh 40 10 22-30 Nov Sun myuser /usr/local/projectors/power-on.sh 20 18 22-30 Nov Mon-Wed myuser /usr/local/projectors/power-off.sh 20 21 22-30 Nov Thu-Fri myuser /usr/local/projectors/power-off.sh 20 17 22-30 Nov Sat-Sun myuser /usr/local/projectors/power-off.sh 40 9 1-22 Dec Mon-Sat myuser /usr/local/projectors/power-on.sh 40 10 1-22 Dec Sun myuser /usr/local/projectors/power-on.sh 20 21 1-22 Dec Mon-Fri myuser /usr/local/projectors/power-off.sh 20 17 1-22 Dec Sat-Sun myuser /usr/local/projectors/power-off.sh syslog excerpt: $ grep power-off.sh /var/log/syslog Nov 22 17:20:01 lanner-ubu-c2d CRON[23007]: (myuser) CMD (/usr/local/projectors/power-off.sh)

  Read the article

< Previous Page | 407 408 409 410 411 412 413 414 415 416 417 418  | Next Page >