Search Results

Search found 33182 results on 1328 pages for 'linux port'.

Page 412/1328 | < Previous Page | 408 409 410 411 412 413 414 415 416 417 418 419  | Next Page >

• bash code in rc.local not excuting after bootup

  - by mrTomahawk

  Does anyone know why a system would not execute the script code within rc.local on bootup? I have a post configuration bash script that I want to run after the initial install of VMware ESX (Red Hat), and for some reason it doesn't seem to execute. I have the setup to log its start of execution and even its progress so that I can see how far it gets in case it fails at some point, but even when I look at that log, I am finding that didn't even started the execution of the script code. I already checked to see that script has execution permissions (755), what else should I be looking at? Here is the first few lines of my code: #!/bin/sh echo >> /tmp/configLog "" echo >> /tmp/configLog "Entering maintenance mode"

  Read the article

• Log rotation with automatic *.log file discovery

  - by Mikko Ohtamaa

  I am hosting several websites which each of run their own Python process and write *.log output files, but the directory structure is not standardized. Example: -rw-r--r-- 1 plone plone 125M 2012-08-29 11:35 ./x/var/log/instance-Z2.log -rw-r--r-- 1 plone plone 19M 2012-08-29 00:07 ./zope2.9/y/log/event.log -rw-r--r-- 1 plone plone 188M 2012-08-13 00:09 ./zope2.9/y/log/Z2.log -rw-r--r-- 1 plone plone 137M 2010-11-16 09:41 ./zope2.9/y/log/event.log I'd like to make log rotate autodiscovery these log files and run a log rotation on them, as opposite to manually type in every log file to logrotate conf. Does any existing tools offer this kind of log file discovery and rotation capabilities, without manually specifying each file? If not... then just write a shell script which generates the logrotate conf?

  Read the article

• Very slow disk performance on Dell PowerEdge 2950 w/ PERC 6/i running RAID 10

  - by vocoder

  I recently set up a server running Ubuntu 10.04 LTS on a Dell PowerEdge 2950 server - it has 6 500 gb 7200RPM SATA drives setup in a RAID 10 config. I am seeing extremely poor disk performance - the RAID array reports all disks are normal and using MegaCLI, it looks like the BBU is fine. hdparm -tT /dev/sda reports: Timing cached reads: 90 MB in 2.05 seconds = 43.96 MB/sec Timing buffered disk reads: 24 MB in 3.11 seconds = 7.72 MB/sec So as you can see, it takes forever to something as simple as an apt-get upgrade and even logging into the server. How do I go about troubleshooting what is causing this? I upgraded the firmware on the PERC 6i RAID controller to the latest, but didn't see any improvements.

  Read the article

• Installing Midnight Commander from sources (no root privileges)

  - by ouroboros

  I tried to configure ./configure --prefix=/localfolder glib-2.26.1/ make make install but it fails at make stage. trying to configure mc-4.6.1/ and make doesn't obviously work. What are the steps I need to make in order to install midnight comander for my local user in a custom folder? Make for glib gives me these errors /usr/bin/msgfmt: found 2 fatal errors cp: cannot stat `test.mo': No such file or directory gmake[4]: *** [test.mo] Error 1 gmake[4]: Leaving directory `/remote/folder/mc/glib-2.26.1/gio/tests' gmake[3]: *** [all-recursive] Error 1 gmake[3]: Leaving directory `/remote/folder/mc/glib-2.26.1/gio' gmake[2]: *** [all] Error 2 gmake[2]: Leaving directory `/remote/folder/mc/glib-2.26.1/gio' gmake[1]: *** [all-recursive] Error 1 gmake[1]: Leaving directory `/remote/folder/mc/glib-2.26.1' gmake: *** [all] Error 2

  Read the article

• How to make new file permission inherit from the parent directory?

  - by Wai Yip Tung

  I have a directory called data. Then I am running a script under the user id 'robot'. robot writes to the data directory and update files inside. The idea is data is open for both me and robot to update. So I setup the permission and owner group like this drwxrwxr-x 2 me robot-grp 4096 Jun 11 20:50 data where both me and robot belongs to the 'robot-grp'. I change the permission and the owner group recursively like the parent directory. I regularly upload new files into the data directory using rsync. Unfortunately, new files uploaded does not inherit the parent directory's permission as I hope. Instead it looks like this -rw-r--r-- 1 me users 6 Jun 11 20:50 new-file.txt When robot tries to update new-file.txt, it fails due to lack of file permission. I'm not sure if setting umask helps. In anycase the new files does not really follow it. $ umask -S u=rwx,g=rx,o=rx I'm often confounded by Unix file permission. Do I even have a right plan? I'm using Debian lenny.

  Read the article

• Can I recover a nano process from a previous terminal?

  - by davidparks21

  My system crashed while I was in a nano session with unsaved changes. When I log back in via SSH I see the nano process still running when I do a ps. davidparks21@devdb1:/opt/frugg_batch$ ps -ef | grep nano 1001 31714 29481 0 18:32 pts/0 00:00:00 nano frugg_batch_processing 1001 31905 31759 0 19:16 pts/1 00:00:00 grep --color=auto nano davidparks21@devdb1:/opt/frugg_batch$ Is there a way I can bring the nano process back under my control in the new terminal? Or any way to force it to save remotely (from my new terminal)?

  Read the article

• Why does the Java VM process eat up more RAM then specified in -Xmx parameter?

  - by evilpenguin

  I have multiple servers running CentOS 5.4 and only one application running on Java VM. I've configured the Java VM with the following arguments: java -Xmx4500M -server -XX:+UseConcMarkSweepGC -XX:+CMSIncrementalMode -XX:NewSize=1024m -Djava.net.preferIPv4Stack=true -Dcom.sun.management.jmxremote=true The machines I'm running the VM on has 6 GB RAM and no other applications running. After a while, the java process starts to hit the swap space really hard, I get this info out of the top command: 7658 root 25 0 11.7g 3.9g 4796 S 39.4 67.3 543:54.17 java On the other hand, if I connect via JConsole, it reports the Java VM has 2.6 GB used, 4.6 GB commited and 4.6 Gb max. java -version returns: java version "1.6.0_17" Java(TM) SE Runtime Environment (build 1.6.0_17-b04) Java HotSpot(TM) 64-Bit Server VM (build 14.3-b01, mixed mode) Why is the Java VM expanding so much past it's allocated heap size? And where does that memory go, if it's not reported in JConsole?

  Read the article

• Restarting shell script with &disown using Monit

  - by Solas Admin

  I have a shell script that runs a C++ backend mail system (PluginHandler). I need to monitor this process in Monit and restart it if it fails. The script: export LD_LIBRARY_PATH=/usr/local/lib/:/CONFIDENTAL/CONFIDENTAL/Common/ cd PluginHandler/ ./PluginHandler This script does not have a PID file and we run this script by executing ./rundaemon.sh &disown ./pluginhandler starts the process and starts logging into /etc/output/output.log I stop the process by identifying the process ID with [ps -f | grep PluginHandler] and then killing the process. I can check the process in Monit just fine, but I think Monit is starting the process if it is not running but it can't do &disown so the process ends as soon as it starts. This is the code in the monitrc file for checking this process: check process Backend matching "PluginHandler" if not exist then alert start "PATH/TO/SCRIPT/rundaemon.sh &disown" alert [email protected] only on {timeout} with mail-format {subject: "[BLAH"} I tried to stop the script from terminating by modifying the script like the following but this does not work either. export LD_LIBRARY_PATH=/usr/local/lib/:/home/CONFIDENTAL/production/CONFIDENTAL/Common/ cd PluginHandler/ (nohup ./PluginHandler &) return Any help to write a proper Monit rules to resolve this issue would be greatly appreciated :)

  Read the article

• Unable to Access Certain Websites

  - by codejoust

  Through a local network, all computers except one ubuntu machine can access 1. Adobe.com 2. Icann.org 3. Apache.org 4. Example.com. The ubuntu machine returns (in firefox): "Though the site seems valid, the browser was unable to establish a connection." Furthermore, when I traceroute those websites using the ubuntu machine, they all return ubuntu.local, and it ends there: (traceroute to icann.org (192.0.32.7), 30 hops max, 40 byte packets 1 ubuntu.local (192.168.1.105) 3000.791 ms !H 3000.808 ms !H 3000.814 ms !H I've checked the hosts file, and there isn't anything in there, and I have an apache server there so if it was redirected to localhost, I'd probably see the localhost webroot page. Thanks in advance! user@ubuntu:~$ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 The Ubuntu Machine is one of six on the network. I'm using opendns for dns, so I do think that should be a problem.

  Read the article

• how to hear mic sound over speakers- ubuntu karmic

  - by ashishsony

  Hi, I want to hear the sound that goes into the notebook's mic from the notebook's speaker itself. I am on ubuntu 9.10 Any help is much appreciated. Thanks.

  Read the article

• Run Script on logout/ shutdown ubuntu

  - by gitnoob

  Hi. I want to run some commands every time a user of an ubuntu 9.10 machine logs out or shuts down. What is the best way to do this? Every user uses gnome if that helps.

  Read the article

• How to automate kinit process to obtain TGT for Kerberos?

  - by tore-

  I'm currently writing a puppet module to automate the process of joining RHEL servers to an AD domain, with support for Kerberos. Currently I have problems with automatically obtain and cache Kerberos ticket-granting ticket via 'kinit'. If this were to be done manually, I would do this: kinit [email protected] This prompts for the AD user password, hence there is a problem with automate this. How can i automate this? I've found some posts mentioning using kadmin to create a database with the ad users password in it, but I've had no luck. Thanks for input

  Read the article

• Problems connecting Centos on VMware player to the network using bridged connection.

  - by Sakin

  Hi, I installed CentOs on VMware Player 3.0.1 running on windows XP. When trying to configure it to connect to the internet in a bridged configuration, I get an error message when trying to bring up the network interface: [root@VMLinux ~]# /et/init.d/network start Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... failed [FAILED] VM is running on a machine that has access to the network, I tried it on two different networks that have DHCP enabled. Everything works fine when using a NAT connection through my host. How can I make the bridge work for me? Thanks.

  Read the article

• How to log error queries in mysql?

  - by Kaizoku

  I know that there is general_log that logs all queries, but I want to find out which query has an error, and get the error message. I have tried running an error query on purpose, but it logs as a normal query and doesn't report it with error. Any ideas?

  Read the article

• Help me understand Ubuntu user/group permissions.

  - by Bartek

  I'm beginning to deal with more than one user on my system (it's a VPS serving some sites) and I need to make sure I understand how group permissions work. Here's my setup: I have an account named "admin" .. it's basically the primary account that is used for serving most of the sites that I control myself. Now, I added a second account named "Ville" as one of my users wants to be able to administer that site. So, I can do this the easy way and just chown their domains folder under the ville user and viola, they have permission to do whatever they need be and so forth. However, let's say I want to also give the admin user access to the files (modifying and all) .. how can I put both users into the same group and give them both permission? I've tried doing: sudo usermod -a -G admin ville To add the ville into the admin group, but ville still cannot edit files by admin. Permissions for the primary directory for the ville user are read/write for both owner and group, and the current group for the files is admin:admin .. But ville still can't write into the directory. So, what should I be doing here to get this right and secure at the same time? Thank you.

  Read the article

• IPv6 Routing / Subnetting

  - by nappo

  Recently I have installed Citrix Xen Server 6.2 on a machine. My Provider (Hetzner) gave me the IPv6 Subnet 2a01:4f8:200:xxxx::/64. Followed an article in the providers wiki (1) i got it working and can assign IPs to my guests (CentOS). However i can't assign a second IP to a single guest - it will result in a timeout. I'm not very familiar with IPv6 routing / subnetting - any help or tips for further troubleshooting is welcome! My Setup: XenServer 6.2 IPv6: 2a01:4f8:200:xxxx::2/112 ip -6 route: 2a01:4f8:200:xxxx::/112 dev xenbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 default via fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 Guest 1 IPv6: 2a01:4f8:200:xxxx::3/64 IPv6: 2a01:4f8:200:xxxx::4/64 ip -6 route: 2a01:4f8:200:xxxx::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::1 dev eth0 metric 1 mtu 1500 advmss 1440 hoplimit 4294967295 Guest 2 IPv6: 2a01:4f8:200:xxxx::5/64 Guest 1 IPv6 is working fine, Guest 2 too. As suggested by the wiki article (1) i split my /64 network into a /112. Is it right to set the host /112 and the guests /64? Why is that?

  Read the article

• APC File Cache not working but user cache is fine

  - by danishgoel

  I have just got a VPS (with cPanel/WHM) to test what gains i could get in my application with using apc file cache AND user cache. So firstly I got the PHP 5.3 compiled in as a DSO (apache module). Then installed APC via PECL through SSH. (First I tried with WHM Module installer, it also had the same problem, so I tried it via ssh) All seemed fine and phpinfo showed apc loaded and enabled. Then I checked with apc.php. All seemed OK But as I started testing my php application, the stats in apc for File Cache Information state: Cached Files 0 ( 0.0 Bytes) Hits 1 Misses 0 Request Rate (hits, misses) 0.00 cache requests/second Hit Rate 0.00 cache requests/second Miss Rate 0.00 cache requests/second Insert Rate 0.00 cache requests/second Cache full count 0 Which meant no PHP files were being cached, even though I had browsed through over 10 PHP files having multiple includes. So there must have been some Cached Files. But the user cache is functioning fine. User Cache Information Cached Variables 0 ( 0.0 Bytes) Hits 1000 Misses 1000 Request Rate (hits, misses) 0.84 cache requests/second Hit Rate 0.42 cache requests/second Miss Rate 0.42 cache requests/second Insert Rate 0.84 cache requests/second Cache full count 0 Its actually from an APC caching test script which tries to retrieve and store 1000 entries and gives me the times. A sort of simple benchmark. Can anyone help me here. Even though apc.cache_by_default = 1, no php files are being cached. This is my apc config Runtime Settings apc.cache_by_default 1 apc.canonicalize 1 apc.coredump_unmap 0 apc.enable_cli 0 apc.enabled 1 apc.file_md5 0 apc.file_update_protection 2 apc.filters apc.gc_ttl 3600 apc.include_once_override 0 apc.lazy_classes 0 apc.lazy_functions 0 apc.max_file_size 1M apc.mmap_file_mask apc.num_files_hint 1000 apc.preload_path apc.report_autofilter 0 apc.rfc1867 0 apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.serializer default apc.shm_segments 1 apc.shm_size 32M apc.slam_defense 1 apc.stat 1 apc.stat_ctime 0 apc.ttl 0 apc.use_request_time 1 apc.user_entries_hint 4096 apc.user_ttl 0 apc.write_lock 1 Also most php files are under 20KB, thus, apc.max_file_size = 1M is not the cause. I have also tried using 'apc_compile_file ' to force some files into opcode cache with no luck. I have also re-installed APC with Debugging enabled, but nothing shows in the error_log I have also tried setting mmap_file_mask to /dev/zero and /tmp/apc.xxxxxx, i have also set /tmp permissions to 777 to no avail Any clue anyone. Update: I have tried following things and none cause APC file cache to populate 1. set apc.enable_cli = 1 AND run a script from cli 2. Set apc.max_file_size = 5M (just in case) 3. switched php handler from dso to FastCGI in WHM (then switched it back to dso as it did not solve the problem) 4. Even tried restarting the container

  Read the article

• What can go wrong with a GLIBC upgrade?

  - by Sevenless

  I recently installed a piece of software that my group needs for a research project starting next September. Turns out the software has a known crash bug when used with glibc 2.12.1. My boss asked if we can upgrade glibc on the server that's supposed to run it. Cue my skeptical silence.... At some point, I got it into my brain that messing with glibc was about as good an idea as messing with a hungry puma; however, I've been unable to determine the source of this belief. So, if I go ahead with this: Am I doing something flagrantly stupid (e.g. I won't fix my problem, I will brick my server, or I will initiate a zombie apocalypse)? What can go wrong? What is likely to go wrong? How do I avoid the answers to 2 and 3?

  Read the article

• Can't ping through default gateway

  - by Andrew G.H.

  I have the following configuration: Routing table on M3 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.3.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 Routing table on M1 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 So basically M3's gateway is M1, and M1's gateway is M2's wireless internet interface. If I ping 8.8.8.8 from M1, everything is ok, replies are received. Pinging from M1 to M3 and viceversa is also possible. I have configured M1 as gateway trafic forwarder using firestarter package and stopped firewall with it. iptables policies are ACCEPT for everything. Problem: I have tried ping-ing ip 8.8.8.8 from M3 but without success. What could be the source of this problem?

  Read the article

• Anonymous user with proftpd on fedora

  - by stukerr

  Hi there, I am trying to setup an anonymous user account on our server to enable people to downlaod technical manuals for our products etc. and I would like this to be as secure as possible! I was just wondering if anyone knew a series of steps that will allow me to create an anonymous ftp account linked to a directory on the server that enables download only ? Also how could i make a corresponding ftp account with write priviledges to this account to allow people within our company to upload new files ? Sorry i'm a bit new to all this! Many Thanks, Stuart

  Read the article

• How to correctly partion WD "Advanced Format" drive (4k sector size) with Disk Druid?

  - by FractalizeR

  Hello. Unaligned Advanced Format drives with sector size of 4k will have degraded performance. How do I make Disk Druid to partition drives correctly?

  Read the article

• bash script with permanent ssh connection

  - by samuelf

  Hi, I use a bash script which runs /usr/bin/ssh -f -N -T -L8888:127.0.0.1:3306 [email protected] However, when I run the bash script, it waits.. I see the connection coming up but the script doesn't exit.. it's like it's waiting for the SSH process to finish, because when I manually kill it the bash script finishes as well. Any ideas how to resolve this? UPDATE: I have croned this script.. and the cron process is the one that becomes a zombie.. the actual scripts runs just fine, sorry about that, with ps -auxf I get: root 597 0.0 0.7 2372 912 ? Ss Jul12 0:00 cron root 2595 0.0 0.8 2552 1064 ? S 02:09 0:00 \_ CRON 1001 2597 0.0 0.0 0 0 ? Zs 02:09 0:00 \_ [sh] <defunct> 1001 2603 0.0 0.0 0 0 ? Z 02:09 0:00 \_ [cron] <defunct> and when I kill the ssh the defuncts disappear.. why would they become defunct?

  Read the article

• Centos 5.5 [Read-only file system] issue after rebooting

  - by canu johann

  I have a virtual server under centos 5.5 (hosted by a japanese company called sakura ) Since yesterday, connection through ssh couldn't be established. I've contacted support center who told me to restart VS from the control panel. After restarting, I got the message below Connected to domain wwwxxxxxx.sakura.ne.jp Escape character is ^] [ OK ] Setting hostname localhost.localdomain: [ OK ] Setting up Logical Volume Management: No volume groups found [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/vda3 / contains a file system with errors, check forced. /: Inodes that were part of a corrupted orphan linked list found. /: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY. (i.e., without -a or -p options) @@cat: /proc/self/attr/current: Invalid argument Welcome to CentOS Starting udev: @[ OK ] Setting hostname localhost.localdomain: [ OK ] Setting up Logical Volume Management: No volume groups found [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/vda3 / contains a file system with errors, check forced. /: Inodes that were part of a corrupted orphan linked list found. /: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY. (i.e., without -a or -p options) [FAILED] *** An error occurred during the file system check. *** Dropping you to a shell; the system will reboot *** when you leave the shell. *** Warning -- SELinux is active *** Disabling security enforcement for system recovery. *** Run 'setenforce 1' to reenable. /etc/rc.d/rc.sysinit: line 53: /selinux/enforce: Read-only file system Give root password for maintenance (or type Control-D to continue): bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system (Repair filesystem) 1 # setenforce 1 setenforce: SELinux is disabled (Repair filesystem) 2 # echo 1 (Repair filesystem) 4 # /etc/init.d/sshd status openssh-daemon is stopped (Repair filesystem) 5 # /etc/init.d/sshd start Starting sshd: NET: Registered protocol family 10 lo: Disabled Privacy Extensions touch: cannot touch `/var/lock/subsys/sshd': Read-only file system (Repair filesystem) 6 # sudo /etc/init.d/sshd start sudo: sorry, you must have a tty to run sudo (Repair filesystem) 7 # I have 4 site in production and I need to restart the server quickly (SSH + HTTPD ,...). Thank you for your time.

  Read the article

• Convert KVM virtual machine to LXC container

  - by linkdd

  I have 2 virtual machines (with Debian, using KVM) with virtual hard drives: /srv/kvm/ssh.img /srv/kvm/www.img Both have 3 partitions (/, /home, swap). I want to convert them in a RootFS usable with LXC (in order to use LXC instead of KVM). The only solution I have for the moment is: create a new RootFS copy /home partition into it reproduce the same configuration into it But is there an automated way to do it

  Read the article

• Weird noise while scanning, using scanimage and a Canon Lide 35

  - by Manu

  I'm trying to scan a bunch of images, using xsane's scanimage : scanimage --format=tiff --batch --batch-prompt This command scans the first picture perfectly, but as soon as I press enter, the scanner makes a weird noise, and the scanning "arm" moves very, very slowly. If I stop scanimage and start again, it scans normally again. Is there another scanimage option that I need to add? I've checked the man page, but can't see what I'm missing. Edit: the problem seems to be that the scanning "arm" doesn't go back to it's original position after the first scan.

  Read the article

< Previous Page | 408 409 410 411 412 413 414 415 416 417 418 419  | Next Page >