Search Results

Search found 12829 results on 514 pages for 'hard'.

Page 418/514 | < Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• How do I get to the bottom of network latency and bandwidth issues

  - by three_cups_of_java

  I recently moved two blocks south. That move moved me from Comcast to Broadstripe (high-speed internet cable providers). Comcast was pretty good. Broadstripe sucks. I called them on the phone, and they basically brushed me off (politely). I want to come to them with some numbers, so I can say more than just "it's really slow". I still have access to my old Comcast service, so I can run the tests using both providers. Here's what I'm seeing with my new Broadstripe service: 1) When I browse to most sites, there is a long delay (5-10 seconds) before the page starts loading in my browser 2) The speed test tell me I have 12 megs down (bullshit) 3) I have a server at my office. I just downloaded some files (using scp on the command line). It said I'm getting 3.5 KB/s I'm an experienced programmer and spend most of my days on the command line and in vim. Networking, however is not a strong point. I've played around with traceroute, but I'm not sure if that's the right tool to use. I have access to servers all over the country (I would just use Amazon EC2 to set up a test server), and I prefer to use Ubuntu for my testing. How can I come up with some hard numbers to show Broadstripe how crappy their service is?

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Hi - Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message : "Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions? Many thanks Clem

  Read the article

• Basic connectivity issues between Win 7 and XP mixed wired/wireless network. [Solved]

  - by Pulse

  Setup: Windows 7 x64 Ultimate desktop hard wired to Asus WL500gp router (WL500gpv2-1.9.2.7-d-r1445 firmware) Several Bridged VirtualBox VM's running XP, 7, ubuntu server 10.04, Mint 9 and SuSE 11.2 Win XP Pro SP3 notebook with D-Link Airplus wireless network card. No firewall or other security software currently running on either platform (at least for the duration of the test) Situation: Router is acting DHCP server Clients are receiving correct addresses and additional parameters Internet connectivity is available from all clients Windows 7 sharing is set to Network type = work (not home group) NetBT is disabled on all clients using smb over TCP What I can do: I can ping the router and internet addresses from the wireless XP notebook I can ping the Win 7 desktop and any VM from the XP wireless notebook I can ping all devices from the router All VM's and 7 can ping each other and the router as well as Internet addresses What I can't do: I cannot ping the XP wireless notebook from either the Win 7 desktop or the VM's; it always returns a destination host unreachable error. Tracert resolves the name or the XP notebook but also returns a destination host unreachable. From the above it would seem that something is blocking connectivity in a single direction (from the Win 7 box to the Win XP notebook) only but the router can ping the XP notebook. Some fresh input would be most welcome, as this is beginning to drive me batty. Thanks

  Read the article

• Grub Installation Failed: Fatal Error ... now what I do?

  - by eklavya

  I know there are some threads that touch this but I feel I have done something uniquely stupid. hence the post and plea for help. I am a beginner @ Linux. So I have a PC with a HDD (hard disk drive) and SSD (solid state drive) It was running Linux Mint /dev/sda1 - HDD Partition 1 - 2 TB (mounted this is /home /dev/sda2 - HDD Partition 2 - 1 TB (separate back up drive, i was backing up files to this) /dev/sdb1 - SSD Partition 1 - 100 GB (OS) /dev/sdb2 - SSD Partition 2 - 20 GB (Swap) The operating system was Linux Mint and was installed on the /dev/sdb1 i.e the solid state drive. I had partitioned off the sda into 2 TB and 1TB and presented the 2 TB as the /home to the OS. Anyway last night I decided to make a return to Ubuntu via the path of Elementary OS. Everything went fine with the install until it stated that GRUB installed failed and this was a Fatal error (no kidding I said). No I am stuck. I have definitely done something wrong and don't know what it is... My biggest pain is the files on the /dev/sda2. I want to save these before I try something drastic like wiping off the /dev/sda completely. So I have the following questions... Can I use a liveCD USB to save these files ? I can see the /dev/sda2 but was unable to access the files in the liveCD last not least ... how do I fix the main issue here. Why could the OS not install GRUB 2b... why is my SSD the /dev/sdb ... and not /dev/sda. Does that have something to do with it that my master boot record sits on the HDD /dev/sda and not /dev/sdb

  Read the article

• Booting Windows from different partition than system

  - by szamil

  I have bought an SSD disk, but my laptop (Dell Precision M6300) refuse to use it as a target disk for windows (AHCPI on/off, BIOS up-to-date). I can't exchange the disk unfortunately... But fortunately, I've managed to install windows using USB disk case. The problem is, that when I put that disk as my internal drive it can't boot. (Disk read error, Three Finger Salute ... ) So I tried with Linux (openSUSE), I manage to install it as well, but when I tried to boot GRUB from internal drive I get errors again. (Should I try GRUB2?) I figured out that I can boot into that internal hard drive's openSUSE system using small USB drive with GRUB, kernel and image on it. So, I just run GRUB from USB drive, it loads necessary stuff from the USB drive and then continues from the internal drive. I want to do the same with Windows. But GRUB (rootnoverify and chainloader +1) does not boot my windows on internal drive. The question: is there any chance to copy the critical windows' boot files into the USB drive, to make it possible to boot from that USB drive, but continue booting from internal (different in general) drive? The USB drive would became a system hardware key! ;-) Disk: Plextor M5S 128GB Sata III, laptop has Sata II, but it's compatible anyway, right?

  Read the article

• Accessing or Resetting Permissions of a Mounted Registry Hive of a Different User / From a Different System

  - by Synetech

  I’m currently stuck using my backup system until I can replace my dead motherboard. In the meantime, I have put my hard-drive in this system so that I can access my files and keep working on the backup system. Fortunately, I don’t have a permission issues with the files (the partitions are FAT32). The issue I’m having is with the registry. I need to import some of my settings from the hives of my (old? normal?) installation of Windows into the one I’m currently using. Settings from the system hives (SYSTEM, SOFTWARE, etc.) are fine, but the user hive is giving me trouble. I’ve copied the NTUSER.DAT file from my other drive and mounted it with the reg command. Most of the keys (eg Software) are fine and I can access them without problem, but some of them (particularly the Identities key where Outlook Express settings are stored) complains that it cannot be opened. If I open the permissions dialog, I get an error about being unable to view the current permssions. If I then ignore it and try to take ownership of the key and it’s subkeys, I get an access-denied error. If I then add permissions for my user account on this system, I get an error, however I am then able to see the subkeys and values of the key. If I then try to access the subkeys, I get the same original errors. If I repeat the process for each subkey, I can see their values and subkeys, and so on, but of course this gets to be incredibly annoying and time-consuming (especially since the Identities key has a lot of subkeys). Is there an easier/temporary/more correct way to dump a key so that I can import it into my backup system?

  Read the article

• Graphics artifacts/distortion with Win7 and nVidia

  - by Gepard

  Problem I encounter is rather hard to describe, so I provide a screenshot: http://dl.dropbox.com/u/1732760/video-distortion.png As you can see there are some horizontal stripes in random colors. These stripes appear sometimes in all windowed apps, games and on the desktop too. They tend to stay in place until I refresh window (or force it to to redraw by for example minimizing and maximizing again). They also tend to appear in the same place and shape multiple times, even if they disappear, it's very likely they will be again in the same place after a while. These artifacts do not blink or change if computer is idling. If I don't touch anything, do not use mouse, they will stay in place forever (unless some app redraws its window on its own). I first encountered this problem some weeks ago. Back then I thought it might be cooling problem, so I took out the graphics card, removed dust from the radiator and fan and put it into PC back. I also ran some stress test using Furmark (peak tempearature was ~65C) to see if the problem becomes more intense if the card gets hotter, but suprisingly no artifacts whatsoever appear during the stress test. Graphic card is Galaxy GeForce 7300 GT with DDR3 memory, was never overclocked. Drivers are the latest, from Nvidia site. OS is Windows 7 64-bit, updated. AMD64 3000+, 2GB RAM. I'm running a dual monitor setup with 2 19'' Samsung LCDs and problem is on both, so I assume it's not a monitor or cable issue.

  Read the article

• running a laptop continuously

  - by intuited

  I have an experienced laptop — a Dell Latitude D400, with a Pentium M CPU — that I'd like to run as an always-on server. This model was launched in 2004; I got mine second-hand in about 2007. I've heard that continuous operation is generally not a good idea with consumer hardware, but am lacking in specific knowledge about related problems, and have little idea of how much such usage patterns would reduce the lifespan of the machine. I'm mostly concerned with the unit's core components; parts such as the hard drive which are readily replaceable are, well, readily replaceable. What sorts of things can I do to increase the lifespan of this machine under such circumstances? For example, I'm guessing that it would be wise to limit the CPU frequency or take other steps to keep the internal temperature low. However, I'm not sure where the point of diminishing returns would lie with such an approach — 50°C? 40°C? Would it be useful to suspend the machine periodically, for perhaps an hour each day, or a few hours each week?

  Read the article

• Hibernate & Sleep broken after IE 9 RTM installation in Windows 7 x64.

  - by AKa

  I have a question about hibernation. I installed Internet Explorer 9 RTM x64 on my Windows 7 x64 SP1 desktop machine. After this, computer don't entry the hibernation or (hybrid) sleep state properly. After I hibernate the computer the monitor become blank screen and the keyboard and mouse are inactive. But the machine is still running and there isn't any possibility to switch them off as only with power button. But this is recognized on next start as ineligible because of log entry with message “The previous system shutdown at xx:xx:xx on ?xx.?xx.?x was unexpected“ and menu with safe mode option. I’m clearly not sure if it has something to do with Internet Explorer installation, but I’m definitely guaranteed that before of this I never had some problems with hibernation or (hybrid) sleep. In Windows logs isn’t something suspect. I switched the hibernation off and on, installed new drivers for mainboard, graphic and network card, checked the hard disk, nothing was helpful. This is really sad, beacuse I don't like to switch the computer completely off because it takes longer to boot. Any suggestions?

  Read the article

• How should an experienced Windows SysAdmin learn Linux? [closed]

  - by Systemspoet

  I have a new hire starting in a few weeks who is an experienced Windows SysAdmin. I think he's fairly senior on the Windows side, with a pretty deep AD understanding and experience with Exchange 2007, 2010, and exchange migrations. He's done a little PowerShell but I suspect more of the "run this command to do this" variety then "write a script to do this" sort. However, we are a mixed shop and (he knows this) I expect him to become a reasonably competent Linux SysAdmin over time. I'm looking for good starting points to bring him along. I have over ten years of Linux/UNIX experience, so it all sort of seems intuitive to me, but I've been thinking about the toolkit you actually need to be productive in the Linux CLI world. Just to be able to use the machines at all, off the top of my head... vi Basic CLI stuff -- move around, rename files, copy files, tar, gzip, changing passwords, finding relevant manpages, keep track of where you are, find things in your history, etc, etc. More advanced things that I take for granted but are actually pretty hard -- doing things with 'find', extracting relevant text via 'awk' and/or 'cut', knowing when to use 'grep' and when to use 'grep -e' or 'egrep'. Distribution specific stuff... compiling software, rpm, yum, apt-get, you name it. This all seems pretty basic to me, but when I think back to 1995 when I was first learning my way, some of those things took me years to master. So my question is -- where should I send him to pick up those skills? I'm not just thinking of classes, but rather also websites and books? Where do you all suggest as a starting point for picking up Linux skills?

  Read the article

• Can I use Upstart to start a script which requires the user's X session?

  - by ledneb

  I wrote a script which greps through the output of synclient to determine whether a laptop's touchpad has miraculously turned itself off (Ubuntu seems to /love/ doing this recently) and, if so, turns it back on. The script is something like this: #!/bin/bash while true ; do if [ `synclient | grep -e"TouchpadOff[\s]*1" | wc -l` -ge 1 ] ; then synclient TouchpadOff=0 fi sleep(3) done (I don't have the laptop to hand right now but you get the point! I will update later when I'm at my laptop if that's incorrect) So I tried running this as an upstart script so my touchpad can heal itself without any interaction. But it seems synclient doesn't find the current user's X session when my script is upstart'ed. I tried running it by using something like su -c myscript.sh ledneb in my script stanza, but to no avail. Should I be looking in the direction of /etc/X11/xinit/xinitrc rather than upstart? Is there a proper way to have this script run in the context of the current (or even a hard-coded) user's x session?

  Read the article

• VirtualBox bridged network not working as expected

  - by iby chenko

  I am having hard time getting Bridged network to work with VirtualBox. Idea is to have host as well as one or more guests on same LAN. Using NAT (default) I do get access to internet and any node on the LAN when working from one of the VM guests. However, no LAN node including host can access (or ping) guest in VM. I need to be able to use any guest as if it was a physical computer on the network (need to be accessed by any machine on LAN). According to my understanding of the VirtualBox documentation, this should be Bridged mode. I think I set it correctly, well, actually there is not much to it: 1. select Bridged mode in VM network setup 2. select physical NIC of the host to connect bridge to 3. start VM When I do this, each VM does get new IP address that corresponds to LAN settings : 192.168.1.100 192.168.1.102 192.168.1.103 etc. where host is 192.168.1.80 / 255.255.255.0 (IP addresses above 100 are served by DHCP server). This seem to be correct based on what I know about ethernet. From VM I can ping other nodes like 192.168.1.50 etc. and I still get ethernet access. So far so good... But I STILL cannot ping any of the other VMs (running ones of course). I cannot ping them from other VMs, from host or from other nodes on the LAN. Aside from fact that IP addresses handed to guests are now local, this still acts same as NAT. What is going on? What am I missing? Regards, I

  Read the article

• Unable to connect to SQL Database (can the password be reset)

  - by user45450

  I have recently joined a company which has an SQL 2005 Server running a few databases. The server looks like no one has touched it in a couple of years and has this week it ran out of disk space. After a quick hard drive scan it looks like some of the databases have become a little bloated and particularly the Sharepoint_config~*~_log and WSS_Content_log.ldf have grown to about 15GB. I have been able to log into a couple of the other databases and use the shrinkfile command to free up disk space but for some reason I am unable to log into the sharepoint and Microsoft#SSEE databases (which gives me the "cannot connect to Sharepoint, a network related or instance specific error occurred..." when I try and connect) I can see that the database is running via the SQL surface configuration and I have made sure that the remote connection settings allow me to connect locally but I am still unable to log in either with windows authentication or locally. Is there any way to reset or recover the database login details so I can get in? ( I have tried logging in with all the administrative passwords I can find and after tracking down the company who installed it in the first place I found out that they have no idea what the password could have been)

  Read the article

• Sizing Switches for Storage and Production

  - by Untalented

  Couple questions. Should you always completely separate the storage network switches from production switches or are VLANs fine to segment this traffic? Is there a golden rule here? How do you properly size a switch for your environment based on the specifications the manufacturer provide (Throughput, Forwarding Throughput, Stacking Throughput, Max Mac)? If you have two switch options and one has a maximum Mac address of 8,000 vs. another with 16,0000. What does this really mean to me? How do make sure one vs. another is sized properly for me? Besides VLAN and Jumbo Frame support, is there any other "Must" haves for a virtual environments production or storage networks? There is a wealth of knowledge on sizing SANs and such, but this seems equally important and it's quite challenging to find as much information. -- Just to add some tidbits of information for the environment. This setup above is referring to the data centers which supports two different locations which have about 100 users between the two in total. The storage traffic will be iSCSI and will be 3 ESXi Hosts and one SAN housing about 2.7TB of data. Since there is currently no storage network in place (no SAN), I'm having a hard time regarding #2 to really determine what backplane throughput and switch specifications will be sufficient.

  Read the article

• Automatic switching of network card when vm is moved

  - by spock

  I have two hosts in a pool and I used to be able to move the vm around and they will start without any problem. But after I played around with some network setting, which I don't remember what, I started getting "This VM needs storage that cannot be seen from that server" message. As you can tell I am a beginner with Xenserver. Here is the very simple environment: 2 host servers with their own local hard disk and network card. One is a Pool master. Problem: Power off a vm and move vm from one server to another, or clone one vm to the other server. It used to be able to start up right away. Now, I need to delete one of the network that does not belong to the server, then it will start. Otherwise, the above error msg popup. The two networks (one for each network card in each host) are in the Networking tab of the vm, as well as in the host's networking tab. I googled but all I got to empty the DVD drive, which is not the problem here. Thanks in advance!

  Read the article

• How can I inject clips [ads] in a playlist every x minutes (even if previous clip is not over)

  - by azera

  Sorry for the title, I find it quite hard to describe what I want to do in a single sentence We have a few TV here linked to our computer, which we use to display clips about what we do in our sport center, what you should do to stay in good form ect ... It's running non stop, actually though vlc + playlist. Those main clips are 1-2 hours long and we have about 20 of them looping randomly all day. We would like to inject ads for some of our sponsiored products every now and then during the playlist, like say one ad every 15 minute. Does any one know how we can do that, while keeping the main clip random order ? I thought about encoding the whole thing as a single movie with ads inserted, but then it's not random. So we can put the ads in the playlist itself right ? Except clips are several hours long and we want that more often than that. Cutting the main clips in several pieces seems to work but that kind of sucks as new clips are made every month. If any one has an idea, thanks a lot

  Read the article

• 64-bit Windows 7 gets stuck on logo screen on bootup

  - by Richard B

  I've had a PC running Windows 7 in my office which I'm not using at the moment (cause I'm working elsewhere as a consultant atm), I'm only accessing the PC using Team Viewer (http://www.teamviewer.com/) which means the PC has been running for quite some time now. I've restarted it maybe twice a week though. A few days ago I couldn't access it using Team Viewer and when I got to the office the screen was black with only the mouse pointer showing. The PC has four hard disks, three of them (all 1Tb) is using RAID 5. This is what I've done so far: I reboot and everything seems to load correctly. I get to a screen that gives me two choices - boot Windows normally or perform a startup repair. Choosing to boot Windows only gets me to the Windows 7 logo screen which only animates over and over again. Choosing to repair gets me to the repair screen that "checks for problems" and then it gets stuck on the "Attempting repairs..."-screen (I let it run for about 24 hours before giving up). What is the next step to take? I don't have any backups and no system restore points saved. I can access files and folders through a terminal window using a Windows 7 DVD so I guess nothing is lost yet... Please help me, thanks!

  Read the article

• PC doesn't POST with a certain model of PSU

  - by Core Xii

  I have this PC with an Asus P5N32-E SLI motherboard and an Intel Q6600 CPU. I got a new RX-5300 PSU, but it didn't work. The motherboard power LED is on fine When I switch power on, the PC powers up briefly (0.5-1 sec) then shuts down From there on out when I switch power on, it stays on, all fans and components seem to be receiving power, but the motherboard won't POST. No video output, no PC speaker beeps, nothing If I turn the hard switch on the PSU off and then back on again, go to step 2; The PC turns on and then off immediately again, and on subsequent power-ups it stays on but won't POST I disconnected every component but the motherboard, CPU and PSU. Still nothing. I tried three other models of PSU on this PC, both of higher (600) and lower (<300) wattage than the 530 on the RX-5300 and they all work fine. At this point I was convinced the PSU was faulty so I returned it. When the replacement arrived, it behaved exactly the same. So two different units of RX-5300 both with the same symptoms, neither working with this motherboard + CPU. Yet, three other models of PSU work perfectly fine. The PC store couldn't reproduce my problem with the returned PSU. I tried resetting the CMOS with the jumper. I tried with both the 4 and 4+4 (with and without the extra +4 connected) CPU connectors (curiously the RX-5300 comes equipped with both). Could it be a statistical probability that I get two units of the same model of PSU that are faulty in the exact same manner? Could the RX-5300 model itself be somehow incompatible with this motherboard? I was under the impression that PSUs were pretty much universal so long as you have the wattage. Could the motherboard be broken in some such a way as to work with certain PSUs but not others? What's going on here?

  Read the article

• Linux 2.6.24-gentoo-r3-comtrance on x86_64 high Useage for unknown reasons

  - by Dorjan

  Hello everyone, I'm a complete rookie when it comes to all things Linux related so please treat me as such and assume I know nothing. That being said my Top says this: top - 12:08:03 up 11 days, 15:36, 0 users, load average: 5.47, 5.53, 5.46 Tasks: 296 total, 2 running, 294 sleeping, 0 stopped, 0 zombie Cpu(s): 6.3%us, 1.4%sy, 0.0%ni, 71.3%id, 20.6%wa, 0.0%hi, 0.3%si, 0.0%st Mem: 8176880k total, 8118236k used, 58644k free, 89312k buffers Swap: 1004052k total, 0k used, 1004052k free, 7235652k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1229 root 15 -5 0 0 0 D 1 0.0 199:28.63 kjournald 2946 root 20 0 1716 676 552 D 1 0.0 145:02.94 syslogd 14553 root 20 0 2644 1268 876 R 1 0.0 0:00.34 top 14609 postfix 20 0 7896 1884 1460 D 1 0.0 0:00.02 bounce 14630 postfix 20 0 7896 1876 1452 R 0 0.0 0:00.00 bounce And my hard drives says: > df -k Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda3 4925556 4474836 200508 96% / /dev/sda5 489992 36090 428602 8% /tmp /dev/sda6 377951852 236171160 122581816 66% /var none 4088440 0 4088440 0% /dev/shm It has been like it for a few days now... I know not what is causing the high server load (Normally around 1.3) can anyone give any tips on how to track down the culprit? Many thanks,

  Read the article

• Looking for a smart sync tool that exactly copies the structure of the source to that of the destination

  - by ????????

  I am a Windows 7 user and looking for a sync tool that exactly copies the structure of the source to that of the destination. The scenario is as follows: I have a laptop in which I save my daily projects. I always bring this laptop wherever I go to work, either at my school or at my house. At school I have a room in which I put an external hard drive to backup my laptop data. Upon arriving at school I always sync the external data with my laptop. Before leaving the school, I also do the synchronization if I make some modification in my laptop data. I do the same thing when I arrive and leave my house. Every month I reformat my laptop because of some trial softwares. I am using SyncToy 2.1 to sync the external drives with my laptop. The problem is as follows. Before formatting my laptop, I sync all external drives with my laptop. For example, My laptop structure: c:\data\file1.ext c:\data\folder1\file2.ext Both external drive structure: d:\data\file1.ext d:\data\folder1\file2.ext After reformatting my laptop, I move the file1.ext to folder1. So my laptop structure becomes, c:\data\folder1\file1.ext c:\data\folder1\file2.ext If I sync external drives with my laptop, I get d:\data\file1.ext d:\data\folder1\file1.ext d:\data\folder1\file2.ext I want the tool also remove d:\data\file1.ext. How to do this?

  Read the article

• thought about shared storage (NFS, Lustre) [closed]

  - by user134880

  Possible Duplicate: Can you help me with my capacity planning? Now I habe small cluster with total of 8 nodes. 6 of them are computing nodes (apache and vmware) and 2 nodes are for storage. 2 storage nodes are identical. Each storage server is linux box with 8 x 1Tb WD RE4 in soft raid 10. 1st box is master and 2nd is slave. Data is mirrored with DRDB. We export NFSv4 shares to Apache (for document root) and iSCSI to Vmware. Now all is working pretty good and stable. But it will be soon time to upgrade our system. I have been thinking of Lustre. Does some one has any real experience with Lustre or NFS medium clusters? Will it be good idea just to upgrade server and change hdd's to 3Tb ? With NFS we will always have only 2 servers to maintain (one primary and one slave). Thanks. QUESTIONS: 1) Does some one used Lustre? In production? I have seen a lot of info about how it is hard to setup Lustre because you need to compile own kernel and patches. It's answers from newbies. Is there some one who has used Lustre for some period of time? 2) About disk upgrades - it's only description of strategy. I'm not asking if it is enough 3Tb or not. I just ask if it is right just to replace hdds instead of adding new server (like with Lustre) Thanks again.

  Read the article

• Apache Virtual Host with directory aliases

  - by brechtvhb

  Hi, I'm trying to set up a dynamic virtual host in apache with a directory alias pointing to a difirent path for every domain. Here's what I'm trying to achive. Say I have 2 domains: * www.domain1.com * www.domein2.com I want both to point to the same index.php file (C:/cms/index.php). Now the hard part ... I want directories or certain file types to point to a diffirent path for each domain. Example: * www.domain1.com/layout -> C:/store/www.domain1.com/layout * www.domain2.com/layout -> C:/store/www.domain2.com/layout * www.domain1.com/image.png -> C:/store/www.domain1.com/image.png * www.domain2.com/image.png -> C:/store/www.domain2.com/image.png However the admin directory should point to the same path again for all sites * www.domain1.com/admin -> C:/cms/admin * www.domain2.com/admin -> C:/cms/admin Is there a way to achieve this kind of behaviour in apache 2.2 without having to create a virtualhost entry for each new domain?

  Read the article

• Windows XP Freezes

  - by Jim Fell

  Hello. I'm running a machine with Windows XP Professional 64-bit. Every so often, it will freeze for no apparent reason. That is, everything stops responding, except the mouse. I can move the mouse around, but I can't click on anything. Keyboard input is also not accepted/received when this problem occurs. The three-finger salute fails to bring up the Task Manager. Even pressing the power button on my computer fails to shut it down. The only way out of this that I have found is to hard-reboot the machine (i.e. pull power or hold power button in for 10 seconds). This problem was occurring on the system when it had all its updates and after a fresh install when not everthing was quite yet updated. I've run the Scandisk utility and the latest version Memtest86 that supports 64-bit architecture; neither found any errors. The last time this happened was on a fresh install of Windows. Only Nero Essentials, Avast antivirus (disabled), Firefox, and Spybot were installed. I was not running Nero, Firefox, or Spybot at the time, and Avast was disabled, so I'm pretty certain this is a Windows issue. Is anybody familiar with this problem or have any pointers? Thanks.

  Read the article

• Dump Trac DB on Windows/XAMPP

  - by Whiteknight

  I have a Trac instance running on a WindowsXP machine with XAMPP. I am trying to migrate the trac instance to a newer Linux-based machine. However, I'm having a hard time getting the database to cooperate. I try to dump the db with this command: sqlite3 C:\tracroot\db\trac.db ".dump" >> mysqldump.sql But the generated file is mostly empty: BEGIN TRANSACTION; COMMIT; So that's not right. For the record my trac instance is running now and appears to have full access to all the contents of the DB. But sqlite3 (located in C:\xampp\apache\bin) can't seem to get any information from the file. The DB file itself has the header "SQLite format 3", so that seems to be correct. I need to know one of two things: How to get this dump working OR An alternate way to migrate the Trac database to the new machine. Update: When I try to open the .db file in sqlite3, I get the error Error: unsupported file format. What format is it in, and why is it unsupported?

  Read the article

< Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >