Search Results

Search found 16188 results on 648 pages for 'connection broker'.

Page 430/648 | < Previous Page | 426 427 428 429 430 431 432 433 434 435 436 437  | Next Page >

• Deployment of broadband network

  - by sthustfo

  Hi all, My query is related to broadband network deployment. I have a DSL modem connection provided by my operator. Now the DSL modem has a built-in NAT and DHCP server, hence it allocates IP addresses to any client devices (laptops, PC, mobile) that connect to it. However, the DSL modem also gets a public IP address X that is provisioned by the operator. My question is Whether this IP address X provisioned by operator is an IP address that is directly on the public Internet? Is it likely (practical scenario) that my broadband operator will put in one more NAT+DHCP server and provide IP addresses to all the modems within his broadband network. In this case, the IP addresses allotted to the modem devices will not be directly on the public Internet. Thanks in advance.

  Read the article

• Cannot access SWITCH thru VPN

  - by MadBoy

  I've VPN connection set up that i connect to company with. I can connect to all devices (other switches, routers, servers from same subnet with same settings just diffrent ip) but I can't connect to NetGear Router GS748Tv3. Settings on switch: IP address 192.168.1.8 Subnet mask 255.255.255.0 Default gateway 192.168.1.1 Management VLAN ID: 0 (1 - 4094 or 0) (0 means all VLANs) Switch has 2 VLAN's configured 1 and 2. I can access this switch thru VPN if i log in to server and from server to switch but this is a little bit slower then normal way. Anything I'm missing?

  Read the article

• Cannot enable Additional drivers for Broadcom in 12.10

  - by Compt

  tl;dr version: Additional Drivers does not work for enabling a driver in Ubuntu 12.10, however it worked in 12.04. I upgraded to Ubuntu 12.10 from 12.04 via a live USB. I did a fresh install to avoid any conflicts. From 12.04 I know that my wireless card has proprietary drivers that could be installed via Additional Drivers. I did eventually find additional drivers in the software sources menu, however when I attempt to switch to Broadcom 802.11 Linux STA wireless driver source from bcmwl-kernel-source, it not only does not work, it in fact disables my wireless completely. The only way to revert this is to restart, and revert back to "do not use the device". Then upon another restart, my wireless will function once again. I was curious if anyone else had this issue, and if there was a fix for it as of yet. I looked on launchpad and it may be a potential bug, but I am unsure. Any help would be greatly appreciated (and sorry for that wall of text). Until then, I'll continue to use my wireless as it is (or revert to 12.04), but I do notice a slower connection without it enabled.

  Read the article

• ArchBeat Link-o-Rama for December 14, 2012

  - by Bob Rhubart

  JMS Step 6 - How to Set Up an AQ JMS (Advanced Queueing JMS) for SOA Purposes | John-Brown Evans John Brown Evans' post continues the series of JMS articles that demonstrate how to use JMS queues in a SOA context. "This example leads you through the creation of an Oracle database Advanced Queue and the related WebLogic server objects in order to use AQ JMS in connection with a SOA composite," John explains. And if you missed the first 5 steps, don't worry – the post includes links. Cloud Deployment Models | B. R. Clouse Looking out for the cloud newbies... "As the cloud paradigm grows in depth and breadth, more readers are approaching the topic for the first time, or from a new perspective," says B. R. Clouse. "This blog is a basic review of cloud deployment models, to help orient newcomers and neophytes." Understanding the JSF Lifecycle and ADF Optimized Lifecycle | Steven Davelaar Would you call that a surprise ending? Oracle WebCenter & ADF Architecture Team (A-Team) member learned a lot more than he expected while creating a UKOUG presentation entitled "What you need to know about JSF to be succesful with ADF." Using Oracle Enterprise Manager Cloud Control 12c with Filer Snapshotting | Porus Homi Havewala This concise technical article includes a script for database backup using snapshots and cataloging in RMAN. Thought for the Day "A program which perfectly meets a lousy specification is a lousy program." — Cem Kaner Source: SoftwareQuotes.com

  Read the article

• Significant OS X Finder lag when listing directories/files

  - by Jack Sleight

  I'm experiencing some significant OS X finder lag, that seems to be purely an issue with Finder itself, and not the HD or any other part of OS X (I'll explain below). The lag only appears to be when listing directories/files, where I'm seeing up to twelve or so seconds of lag (the folder opens with a blank list and the spinner going in the bottom right). This happens with both the local SSD and network drives (connected via ethernet or wifi) Browsing both local and network drives in terminal and listing directories is instant I can actually browse files on my NAS from my phone over a 3G connection from the other side of the country faster than Finder can when connected to the local network (madness!) Can anyone help? Thanks.

  Read the article

• Squid Proxy Server: limit total bandwidth

  - by Pitto

  Hello my dear friends! We have a marvellous squid proxy with dansguardian for filetering and they both work just great. Is there any easy way to limit the total bandwidth usage? I'd like to set the max amount of squid users internet use to 1200 since our total band is 2000 and I need the rest to ensure other services such as voip to work without hiccups related to huge downloads on the "internet side" of our connection and similar issues. I mean a total squid bandwidth limitation and not a user-based. Fair thanks to everybody.

  Read the article

• After virus, IE and Chrome don't work but Firefox does.

  - by Erich

  I recently got rid of a virus on my laptop. Afterwards everything seems to be working fine except for some internet connectivity problems. Internet Explorer and Chrome won't display an webpages, Firefox does but I can't update it to the most recent version. I've also noticed that some of the gadgets on Google Gadgets don't work properly. My internet connection is working fine, especially since I can get to websites via Firefox. I have tried to re-install IE and Chrome, but there was no change. What has caused this and how can I fix it?

  Read the article

• Inverted LACK Table Serves as a Perfect Gear Rack [DIY]

  - by Jason Fitzpatrick

  We’ve seen IKEA gear hacked to hold audio and computer gear before, but this mod adds in a simple and effective twist. LACK end tables are, conveniently, the same width as a standard server rack. This makes it super simple for DIYers to mount their gear right into the legs of the table with no modification necessary. In this case, however, Winston Smith included a clever update to the mod. Rather than leave it like a standard table, he flipped the table upside down for increased stability and a stronger connection between the legs of his improvised audio rack and the table-top-turned-floor-plate. He then finished it with a matching LACK shelf piece to serve as a turn-table stand. His gear is stored cleanly, off the floor, and in a sturdy container all for about $25–a definite bargain when it comes to storage racks. Hit up the link below for more information and pictures. LACK Rack & EXPEDIT Desktop [IKEA Hackers] HTG Explains: How Windows Uses The Task Scheduler for System Tasks HTG Explains: Why Do Hard Drives Show the Wrong Capacity in Windows? Java is Insecure and Awful, It’s Time to Disable It, and Here’s How

  Read the article

• Why does 301 redirect work for http but not for https?

  - by Tom G

  Through my domain registrar I have set up a domain, essayme.co.uk, to automatically forward to https://google.com. If I go to http://essayme.co.uk it works as expected and redirects me to https://google.com. $curl -i http://essayme.co.uk HTTP/1.1 301 Moved Permanently Cache-Control: max-age=900 Content-Type: text/html Location: https://google.com Server: Microsoft-IIS/7.5 X-AspNet-Version: 4.0.30319 X-Powered-By: ASP.NET Date: Sat, 07 Jun 2014 11:14:16 GMT Content-Length: 0 Age: 0 Connection: keep-alive However, if I go to https://essayme.co.uk it just freezes and times out. $curl -i https://essayme.co.uk curl: (7) Failed connect to essayme.co.uk:443; Operation timed out What is happening in the second case? (and, if possible, how can I get the redirect to work for https?) Problem background/clarification: I don't have an SSL certificate for the essayme.co.uk domain above, but I do for my live domain (let's call it mywebsite.com), and I was seeing the exact same problem on this domain (hence why I'm trying to debug the problem). Unfortunately I can't experiment with the live domain (as it's live) and I would like to avoid having to buy a second certificate for essayme.co.uk just for debugging (unless absolutely necessary). The problem I was seeing: my live domain, mywebsite.com (not its real name), has a valid SSL certificate. Visiting https://www.mywebsite.com displayed the webpage as expected. I had set up forwarding (like in the question above) from the naked domain (mywebsite.com) to https://www.mywebsite.com) Visiting http://mywebsite.com redirected to https://www.mywebsite.com as expected. However, visiting https://mywebsite.com would freeze and time out (as in the question above). I also tried forwarding it to http://www.otherwebsite.com as an experiment (i.e. forwarding to another site that does not use SSL), but the result was the same: Visiting http://mywebsite.com redirected to http://www.otherwebsite.com as expected. Visiting https://mywebsite.com would freeze and time out again. So I set up essayme.co.uk as an experiment to try and understand why it doesn't work.

  Read the article

• Need to re-build an application - how?

  - by Tom

  For our main system, we have a small monitor application that sits outside our network and periodically tries to log in to verify the system still works. We have a problem with the monitor though in that the communications component set (Asta 3 inside Delphi applications) doesn't always connect through. Overall, I'd say it's about 95% reliable, but that other 5% kills the monitor since it will try to log in and hang on the connection attempt (no timeout in the component). This really isn't an issue on the client side of the system since the clients don't disconnect and reconnect repeatedly on the same application instance, but I need a way to make sure the monitor stays up and continues working even when the component fails on a run. I have a few ideas as to which way to have the program run, the main idea being to put the communications inside a threaded data module so that if one thread crashes then another thread can test later and the program keep going. Does this sound like a valid way to go? Any other ideas how to ensure a reliable monitoring application with a less than 100% reliable component? Thanks. P.S. Not sure these tags are the most appropriate. Tried including "system-reliability" as one, but not high enough rep to create.

  Read the article

• CloudMail

  - by kaleidoscope

  In Web Applications, we often come across requirement of sending and receiving emails through our application. So same can be for the applications hosted on Azure. So Do you want to send email from an application hosted on Azure? CloudMail is one of the possible answers. CloudMail is designed to provide a small, effective and reliable solution for sending email from the Azure platform directly addressing several problems that application developers face. Microsoft does not provide an SMTP Gateway (yet) so the application is forced to connect directly to one hosted somewhere else, on another network. So to implement such functionality one of the possible option is using Free email providers. This might be fine for testing, but do you really want to rely on a free service in production? There can be other issues with this approach like if your chosen SMTP gateway is down or there are connection problems? Again there can be some specific requirement that, you want to send email via a company’s mail server, from inside their firewall. CloudMail solves these problems by providing a small client library that you can use in your solution to send emails from you application and a Windows Service that you run inside your companies network that acts as a relay. Because the send and relay are disconnected there are no lost emails and you can send from your own SMTP Gateway.   CloudMail is in its Beta version and available for download here.   Technorati Tags: Geeta,Azure Email,CloudMail

  Read the article

• Cannot ssh anymore into FreeBSD 7.2 home server

  - by Gabi

  Somehow sshd stopped running and no amount of start, restart or onestart will make it go again. I normally ssh into it from a dual-boot laptop computer that shows up on the network as gabi-buntu when running Ubuntu Karmic, and as gabi-pc when running Windows XP Pro. Neither my Putty connection nor the Linux terminal can establish a ssh link anymore. Upon rebooting the server, I am greeted with "/etc/rc: WARNING: run_rc_command: cannot run /usr/sbin/sshd". In addition, a message will appear saying things like rpc.statd: failed to contact host gabi-buntu RPC: port mapper failure RPC: timed out Everything else works fine. The FreeBSD 7.2 box runs a print server, a Samba server, and an Apache server for the home wiki, via https. It also serves up NFS shares for Linux clients. Any suggestions? Thank you, Gabi Huiber

  Read the article

• How to forward blocked ports by ISP

  - by KiDo

  So I've been trying to setup a TeamSpeak 3 server on my pc but ports (9987,10011,30033) are blocked by my ISP, I've contacted them to unblock them but they didn't accept, and it's the fastest ISP in my city (as living in a 3rd world country) so it's not a good idea to connect to another ISP. The thing is, I've tried Your-Freedom to connect to tunnel my connection & SocksCap. The problem is, when TS works with SocksCap it doesn't show a WAN-IP that friends will use to connect to my server It says "Needs to be Requested" and when I press the Request button, I get nothing. So, any idea what's wrong if someone has done this before? or if you have any other suggestion to run a TS server, would be very glad to hear it and really appreciate that. P.S. as I've mentioned before, living in a 3rd world country, makes me unable to buy a VPS even the cheapest one cause there's no Visa, Credit, or paypal. so that won't work. Thanks in advance.

  Read the article

• How to increase Remote Desktop resolution?

  - by BugAlert

  I'm using Windows 7 on a PC and connect to it via Remote Desktop Connection for Mac by MS, using a Mac. On the Mac, I have a 27" Display with 2560 x 1440 px resolution. The PC has a high performance graphics card (one of those that needs an additional power supply). Both machines are connected via network cable to a router. So network should be insanely fast. However, the max resolution I can get is 1400 x 1050. The PC just has a old and bad 21" monitor connected to it. How can I increase the resolution to 2560 x 1440 to work fullscreen with the Apple LED Cinema Display via Remote Desktop? Maybe I shouldn't even ask, because I already experience some lag at the low resolution of 1400 x 1050. But I guess this can be resolved as well?

  Read the article

• Backup broken PostgreSQL 8.4 without pg_dump

  - by Daniil

  So. I have a problem. PostgreSQL 8.4 won't start or restart without any output given. But it worked for 3 monthes until hosting provider doesn't rebooted server. Now it is completly broken. It wan't start and doesn't give any output or log. pg_dump: [archiver (db)] connection to database "postgres" failed: No such file or directory Is the server running locally and accepting connections on Unix domain socket "/var/run/postgresql/.s.PGSQL.5432"? Now I want to backup (or just start pgsql socket) my database to reinstall postgesql. How?

  Read the article

• How do I resolve the error "The file exists" when restoring a cube backup?

  - by Ant

  I'm trying to restore a cube backup (a .abf file) using SQL Server Management Studio, but I'm getting the error message: The following system error occurred: The file exists. . (Microsoft SQL Server 2005 Analysis Services) (yes, there really are two dots) Does anyone know how to resolve this so I can restore the backup? Here are the steps I'm using: Open Microsoft SQL Server Management Studio Make the connection to the AS server Right-click on the Databases node on the server tree view Choose Restore... Type in a new database name in Restore database Select the backup file in From backup file Enter the correct password Optionally tick Allow database overwrite (it happens both ways) Press OK -- get the above error message

  Read the article

• Connect to MySQL EC2 Instance outside of VPC

  - by Brian W

  I have a VPC setup with a few EC2 instances inside. I'm attempting to connect to a MySQL database on an EC2 instance outside the VPC, with no luck. I have the security groups on the VPC EC2 instances set to outbound 0.0.0.0/0 which I assumed would let it connect to any outbound connection. I also followed a tutorial on creating a NAT, but wasn't exactly sure how to use it to connect to an external database. In any case, if anyone has experience and knows the proper way to connect to a database outside the VPC, it would be greatly appreciated!

  Read the article

• LAN access via USB from Ipod Touch?

  - by Alec

  I need to browse the local web server from my Ipod Touch to test apps we're developing. I'm not allowed to install a separate wireless access point which would be the easiest solution. Can I use the USB cable for this? Also, the local PC is a Dell Mini 9 running Ubuntu. Has anyone managed to use the wireless port to create an ad hoc connection to an Ipod Touch so the Ipod can browse the Ubuntu web server? This would be an alternate option for me. Thank you!

  Read the article

• Fake domain doesn't resolve when offline

  - by Fletcher Moore

  I have a flimsy grasp of DNS. Nonetheless, in order to install a local development copy of Wordpress MU, I needed to create a fake domain, which I called local.dev. It and all subdomains simply resolve to 127.0.0.1. Apache then directs to the correct folder. I installed PowerDNS, and got it working properly with a MySQL backend. I didn't feel comfortable, but since it worked, I didn't ask any more questions. The bizarre thing is it requires an internet connection to resolve correctly, and now I need to use it offline. If I am offline, Chrome provies the error: Error 105 (net::ERR_NAME_NOT_RESOLVED): The server could not be found. If you need more information, I am happy to provide it.

  Read the article

• What advantages does developing applications for smartphones have over developing the same application as a web application?

  - by Alfredo O

  Let's take the Facebook application as an example. Why did they develop an application when the users could just access to their page and do the same? For me that represents more maintenance and more cost because for each feature added to the web application that feature will have to be added to the smartphone application as well. So why would I want to develop more than once (for each patform iOS, Android, etc) when I could just have one web application? What benefits do I get? The only one that comes to my mind is GPS feature. EDIT: My question is more oriented towards business applications that are going to be used only by some members of the company, it's not about selling the application (private use). So contrary to what some answers say about that by developing as a smartphone application it will benefit from more sells because of the "smartphone stores" for me this point is not important because the application is for private use. By developing the application as a web application it means that it can be accessed through smartphone browser and also in a PC (any capable browser), but developing as a native application would limit this to only some kind of smartphone so we would be limiting the use. On the other hand developing it as a web application means that in order to access the application an Internet connection must be available. So keeping this in mind how would you convince your boss to write the application for a given smartphone platform (iOS/Android) vs developing it as a web application?

  Read the article

• Is an event loop just a for/while loop with optimized polling?

  - by Alan

  I'm trying to understand what an event loop is. Often the explanation is that in the event loop, you do something until you're notified that an event occurred. You than handle the event and continue doing what you did before. To map the above definition with an example. I have a server which 'listens' in a event loop, and when a socket connection is detected, the data from it gets read and displayed, after which the server goes to the listening it did before. However, this event happening and us getting notified 'just like that' are to much for me to handle. You can say: "It's not 'just like that' you have to register an event listener". But what's an event listener but a function which for some reason isn't returning. Is it in it's own loop, waiting to be notified when an event happens? Should the event listener also register an event listener? Where does it end? Events are a nice abstraction to work with, however just an abstraction. I believe that in the end, polling is unavoidable. Perhaps we are not doing it in our code, but the lower levels (the programming language implementation or the OS) are doing it for us. It basically comes down to the following pseudo code which is running somewhere low enough so it doesn't result in busy waiting: while(True): do stuff check if event has happened (poll) do other stuff This is my understanding of the whole idea, and i would like to hear if this is correct. I am open in accepting that the whole idea is fundamentally wrong, in which case I would like the correct explanation. Best regards

  Read the article

• running adb via wifi on ubuntu 13.04

  - by Blaze Tama

  First, im new on linux so please bear with me. I have a rooted android phone and i was able to run the adb via wifi network on windows, where i just need to go to the adb's directory and type adb connect. However, i can't just do that in my ubuntu. Everytime i enter adb connect, the terminal always said that i dont have the adb and i must install it. When i check the ADT Bundle (I downloaded the bundled one from here), i can see the adb is there inside the platform-tools folder. I already tried to change the directory to the platform-tools and run the adb connect from there, but its still not working. Do i need to install the adb again via terminal? Or did i miss something? You may be wondering why dont i just download the adb (again) via terminal and do trial and error? The answer is because i dont have a good internet connection, so i want to avoid unnecessary downloads. Thanks for your time :D

  Read the article

• Share internet with my phone?

  - by Kenneth Cochran

  Most people want to use their cellphone as a modem for their computer, commonly referred to as 'tethering'. I'm actually interested in doing the opposite: Sharing my landline internet connection(which is much faster than any 3G service) with by cellphone. My phone is a Verizon BlackBerry Curve 8330 and it has USB and bluetooth connections. I know both USB and Bluetooth are capable of supporting tcp/ip traffic what's not so clear is: Is IP over USB or Bluetooth standardized? Is it supported on my phone? Has my cellphone company crippled my phone to prevent me from using it?

  Read the article

• IE and Chrome won't browse the internet on dial up but firefox will. How could I fix it?

  - by Kelbizzle

  First let me say I've done plenty of troubleshooting and will try to explain as clearly and as much as I can. Please bear with me. I have a client's computer who uses dial-up and Windows XP. The problem is when I connect to the dial up ISP. IE or Chrome will not browse the internet. It says page cannot be displayed. but if I use firefox on the dialup connection it works. Sounds simple enough there has got to be something wrong with the proxy settings or something...well, that's what I thought here is the weird part. When connected to the LAN in my office IE, Chrome, and FF all work. I upgraded to ie8 and the issue still happens. How would you go about troubleshooting this issue? What should I do next?

  Read the article

• Is it possible to add tcp autotuning to windows xp?

  - by Caspin

  I have a network application that needs to send messages at 60 times a second. The messages are usually 300-400 bytes, but can be as large as 1500. The default setting for SO_SNDBUF is too small and limits the number of message that can be sent if the network latency is anything greater then 100ms. The naive solution is to just bump the SO_SNDBUF size to to something large. However, depending on the latency and the packet size that could be anywhere from 64K to 8MB. One of Vista's new features is TCP autotuning. Autotuning monitors the tcp connection and dynamically adjust the buffer sizes to allow for optimal communication. I would like to use auto tuning on our windows xp machine so I don't need to guess what my buffers sizes should be. Is there a way to install either a microsoft or 3rd party tcp autotuner on windows xp?

  Read the article

< Previous Page | 426 427 428 429 430 431 432 433 434 435 436 437  | Next Page >