Search Results

Search found 12717 results on 509 pages for 'ouaf security'.

Page 432/509 | < Previous Page | 428 429 430 431 432 433 434 435 436 437 438 439  | Next Page >

  • cisco asa + action drop issue

    - by ghp
    Have created a tunnel between 10.x.y.z network and 122.a.b.c ..the tunnel is up and active, but when I try the packet tracer output ..I get the ACTION as drop. I have also enabled same-security-traffic permit intra-interface. Can someone help me what does this drop mean? Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: drop Drop-reason: (acl-drop) Flow is denied by configured rule Packet Tracer output @Shane Madden: please find below the packet tracer output. CASA5K-A# CASA5K-A# config t CASA5K-A(config)# packet-tracer input inside tcp 10.x.y.112 0 122.a.b.c 0 Phase: 1 Type: ROUTE-LOOKUP Subtype: input Result: ALLOW Config: Additional Information: in 0.0.0.0 0.0.0.0 outside Phase: 2 Type: ACCESS-LIST Subtype: Result: DROP Config: Implicit Rule Additional Information: Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: drop Drop-reason: (acl-drop) Flow is denied by configured rule CASA5K-A(config)# ======================================================================== The access-group are as follows : access-group acl-inbound in interface outside access-group acl-outbound in interface inside and the access-list's are access-list acl-inbound extended permit tcp any any gt 1023 access-list acl-outbound extended permit ip object-group net-Source object net-dest

    Read the article

  • Windows takes a very long time to shut down even in safe mode

    - by user1526247
    On Windows 7 the computer freezes for about 5 minutes once it gets to "Shutting down...". I can't remember when it started happening. I just lived with it for a while. The first thing I tried was a full scan using Microsoft Security Essentials. This did not solve the problem. I then went into msconfig and turned off everything I could get away with in the startup and services tabs. This did not solve the problem. I then uninstalled every program on this computer save the most basic programs. This did not solve the problem (did not uninstall drivers or catalyst). I then went through and turned off every single service and did a reboot. This did not solve the problem. I then booted into safe mode and just tried shutting it down. The problem even happens in safe mode. I have tried examining the event logs but with no success. They just say things like "blah blah has entered the stopped state" with no real clues about what program is causing me all this grief. *it may be worth noting that Ubuntu is installed on the same computer and the ubuntu boot loader is the one being used.

    Read the article

  • SMTP Server setting on Windows 2008 R2

    - by user223298
    I am very very new to this and just trying to configure SMTP virtual server. I have followed a few threads to get it all running, but the mails are not being delivered. What I have done so far - 1) Install SMTP server. 2) SMTP server Properties General Tab - IP address is set to 'All Unassigned'. Access Tab - Authentication is anonymous access. Everything else is left to Default settings. Delivery Tab - Outbound security is anonymous access. In Advance section, entered the domain name in the FQDN field, and localhost in Smart host field. 3) Created an Inbound Rule for SMTP service to allow connections to Port 25. When I try to telnet, everything works up until the point the mail has to be send. Now, the sender's domain is different to the receiver's domain. Not sure if settings have to be changed to allow that? I had set the Relay restrictions on SMTP server, but because I couldn't send the mails, I thought I might as well make it work without the relay first. The error I see while sending the mail is 451 Timeout waiting for client input. I used to get some other error before when I had Relay restrictions on. Can anyone please point me in the right direction? Please let me know if you need more information. Thanks.

    Read the article

  • Incorrect Internal DNS Resolution

    - by user167016
    I'm having a DNS issue. Server 2008 R2. The first clue was that after being off the network for a month, I could no longer Remote Desktop into my workstation by name, it wouldn't find it. Both via VPN and internally. But if I connect using its IP, that works. Now I notice in the server's Share and Storage Management, in Manage Sessions, it's displaying the incorrect computer name for some users. So I try, for one example: Ping -a 192.168.16.81 Pinging BOBS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: - replies all successful Then I try Ping RICHARDS_COMPUTER Pinging RICHARDS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: -all replies successful In DHCP, .81 belongs to RICHARDS_COMPUTER I did try flushdns. Not sure if this is related, apologies if it's not, but when I try to connect, I also get prompted: "The identity of the remote computer cannot be verified. Do you want to connect anyway? The remote computer could not be authenticated due to problems with its security certificate. It may be unsafe to proceed.." It then lists the correct name as the name in the certificate from the remote computer, but claims that the certificate is not from a trusted authority. Any thoughts are most appreciated!

    Read the article

  • Must have local user to authenticate Samba to AD?

    - by Phil
    I've got a CentOS 5.3 server with Samba running. I've joined this server to my domain in the hopes of allowing AD users some access to my Samba shares. I've found that this works, but only as long as the AD username that I'm trying to authenticate with is also a local user on the server. In other words, if I'm trying to access a share, and try to authenticate with the AD username "joe", I get errors unless I create a user named 'joe' on the server. I don't have to create a matching password or anything....the local user's password is always blank, so I do know that the authentication is actually happening against the AD. Here's my smb.conf file: [global] workgroup = <mydomain> server string = <snip> netbios name = HOME security = ADS realm = <mydomain.com> password server = <snip> auth methods = winbind log level = 1 log file = /var/log/samba/%m.log [amore] path = /var/www/amore browseable = yes writable = yes valid users = DOMAIN\user1 DOMAIN\user2 DOMAIN\user3 DOMAIN\user4 I would assume that my kerberos settings are fine, as I've joined the domain and can use wbinfo to see users and groups. However, I can provide that info if necessary. Anyone have any ideas?

    Read the article

  • MSMQ on Win2008 R2 won't receive messages from older clients

    - by Graffen
    I'm battling a really weird problem here. I have a Windows 2008 R2 server with Message Queueing installed. On another machine, running Windows 2003 is a service that is set up to send messages to a public queue on the 2008 server. However, messages never show up on the server. I've written a small console app that just sends a "Hello World" message to a test queue on the 2008 machine. Running this app on XP or 2003 results in absolutely nothing. However, when I try running the app on my Windows 7 machine, a message is delivered just fine. I've been through all sorts of security settings, disabled firewalls on all machines etc. The event log shows nothing of interest, and no exceptions are being thrown on the clients. Running a packet sniffer (WireShark) on the server reveals only a little. When trying to send a message from XP or 2003 I only see an ICMP error "Port Unreachable" on port 3527 (which I gather is an MQPing packet?). After that, silence. Wireshark shows a nice little stream of packets when I try from my Win7 client (as expected - messages get delivered just fine from Win7). I've enabled MSMQ End2End logging on the server, but only entries from the messages sent from my Win7 machine are appearing in the log. So somehow it seems that messages are being dropped silently somewhere along the route from XP or 2003 to my 2008 server. Does anyone have any clues as to what might be causing this mysterious behaviour? -- Jesper

    Read the article

  • MSSQL 2008 login failed for windows authentication

    - by Force Flow
    I'm running Microsoft SQL 2008 on a Windows 2008 Server. The MSSQL server server authentication is set to SQL Server and Windows Authentication mode. I have created an active directory security group "xyz app users". I have added a normal user (without any active directory admin privledges) and a user with domain admin privledges to the "xyz app users" group. I have added the group to the MSSQL management console as a login user. This group is a member of the public server role and is mapped to two databases. On a workstation, when the normal user is logged in, I configure a DSN ODBC connection, and I'm able to successfully create the DSN and test the SQL connection. However, when I'm logged in as the user with domain admin privledges, when I attempt to configure the DSN ODBC connection, I can't get past the login ID configuration screen. If I select "windows authentication" and click "next", I get an error: Connection failed: SQLState: '28000' SQL Server Error: 18456 [Microsoft][ODBC SQL Server Driver][SQL Server]Login failed for user 'mydomain\myuser' On the server's application event logs, this error appears: Login failed for user 'mydomain\myuser'. Reason: Token-based server access validation failed with an infrastructure error. Check for previous errors. [CLIENT: 172.x.x.x] And in MSSQL's event logs: Error: 18456, Severity: 14, State: 11 Solutions that I've seen so far do not seem to fit this situation (some solutions I've seen are only applicable when the BUILDIN\Administrator is being used locally on the server, which is not the case here).

    Read the article

  • Cannot connect to a shared network drive

    - by dublintech
    I am using windows 7, I cannot connect to a shared network drive on another machine. I can ping the machine. I can remote desktop connect to the machine. The machine is on the same subnet My friend with the exact same laptop as me (and on the same network, same workgroup) can connect to the shared folder. The machine I am trying to connect to and my friends machine can both see shared folders on my machine. I also cannot see shared folders on the friends laptop. When I select diagnose, windows tells me nothing useful. When I select see details on the error pop up, I see: Error code: 0x80004005 (google doesn't help much) I can nbtstat -a the machine who has the shared folder. When I try with my firewall turned off the same happens. I have ensured my windows 7 has all updates. I run security essentials to ensure my laptop is clean. I run ccleaner to clean up my registry. Same error. I have tried with my laptop on both wireless and ethernet. As you can imagine, I am banging my head against the wall on this one.

    Read the article

  • FDE / SSD - partition and leave some unencrypted?

    - by Web Design Hero
    Just bought a used beast of a desktop pc. The system drive is setup as a Raid 0 SSD (Intel 510 SSD Drives) with 128 each. I will probably not have to many programs beyond office and maybe Adobe CS if I spring for it, I will be keeping big data on a regular hdd. My question is about setting up TrueCrypt with my configuration. I have not previously done full disk encryption, but I feel that its probably a good idea. I have done some speed tests using file containers on the hdd and the sdd with truecrypt. While there is a huge hit with the SSDs and Truecrypt, it still outperforms the hdd on its own by a good margin, so I think i will be okay for my needs with truecrypt. I have seen in a few places that they recommend partitioning the drive and leavign some of the SSD not inside truecrypt, does this really make a difference? If so, how much should I leave? Will there be any issue in the Raid0 configuration? I am not really concerned about all the wear leveling issue, rather loose data and be secure, but since I don't need all that space neccesarily, I would like to optimize my setup for security and speed.

    Read the article

  • customer wont provide ssh access - ftp only

    - by Max
    Eh, here is my problem: I am working in a webdevelopment agency (thats a problem but not the real problem, read on). Most of the time I choose the live server myself when creating a new website project. But now the customer already has a "server" (10 GB on a cheapo host!) and the "admin" refuses to give me ssh access to it. But I need to access the server via shell because many files will be transported (need to be able to upload and extract a tar) and I need to insert or create mysql dumps via command line. He argues FTP and phpmyadmin should be enough... as far as I know the webspace was just ordered to host the website, so no security critical apps are running there. How can I either convince the admin to give me the ssh login or tell management that we need our own server? Anyone with similiar experiences? This is really annoying as this is a very small project that should be done fast and now one has to fight in order to just get the work done...

    Read the article

  • What are secure ways of sharing a server (ssh+LAMP) with friends?

    - by Bran the Blessed
    What is the best way to share a virtual server with friends? More precisely, I have the following assets: A virtual private server (Debian Lenny) with root access for myself, running... SSH apache2 mysql Some unused disk space Some friends in need of hosting The problem I would now like to do the following: Hosting one or several domains per friend My friends should have full access to their domains, including running PHP scripts, for example My friends should not be able to poke around in other directories The security of my server should not be compromised by faulty PHP scripts To clarify: I do trust my friends in the sense that they are not trying to do something evil with their access. I just do not trust the programs they are going to run. So, what are your recommendations for establishing such a scenario? Partial solution I already came up with the following plan: Add chrooted SSH users for my friends Add Apache vhosts per user (point the directories to subdirectories of the homedirectories, i.e. /home/alice/example.com, /home/bob/example.net, etc. But how can I enforce a chroot-like environment for the scripts they are running within these vhosts? Any pointers would be appreciated.

    Read the article

  • IIS_IUSRS cannot access files uploaded and created by Network Service - error 401.3

    - by Max
    Let me rephrase my question as I investigated further: The problem: I have a php script that is used to upload images on my windows webserver 2008. The files are created in the correct directory. The are created and owned by the user Network Service. Network Service has full access to the uploaded file. As soon as I try to access the uploaded file (mostly an image) via HTTP, I get an 401.3 not authorized error. Now, if I right-click on the not accessible image and grant IIS_IUSRS group read permissions via the security tab, the image can be accessed! By default IIS_IUSRS has NO access at all for the uploaded file. The directory containing the image files has the correct access rights set. But each file that is new uploaded to the directory is permitted for IIS_IUSRS. The question: How can I grant IIS_IUSRS by default access to the newly uploaded file? The appPool of the website has its identity set to its default, I also tried setting it to "networkIdentity" or so, but that did not work either.

    Read the article

  • Connect from Mac OS X to Windows 7 Desktop

    - by jrn
    I am trying to connect from my MacBook to my Windows 7 machine within my own network - if it will work from outside my network that's a plus but no need to have. My Windows 7 machine is freshly installed with Windows 7 Home Premium. It runs the built-in firewall with no settings changed so far as well as Microsoft Security Essentials. So far I tried CoRD and Microsofts Remote Desktop Connections to connect from my Mac to my Windows machine without any success. I did try and disabled the firewall on my Windows machine but could not connect either. The reason I did this was to check wether there is a Windows firewall setting preventing me from connecting. On top of that I manually started the Remote Desktop Services and Remote Desktop Configuration within services.msc. Is there anything else I have to enable for a remote desktop connection? Could there be any router setting I have to tweak? Since I do not want to connect from outside my own network I thought I don't have to do any port forwarding. The error messages I retrieve are all connection timeouts. I can however ping the hostname and/or IP address. Any help would be greatly appreciated. Thanks a lot, jrn

    Read the article

  • Moving an external hard drive while running

    - by user1108939
    I mean physically moving the drive around. I've never dealt with external hard drives before. Just plugged this wd mypassport to test the transfer rate. At one point I 'safely ejected' the drive. A minute later I decide to check the underside of the drive, not realizing the disk is still spinning. I lift the drive, rotating my writs about 70 degrees to the left... I hear a sequence of three high pitched sounds. I couldn't determine whether that was an indication beep by an internal security feature or the head scratching the plate (oh god...). Drive stops and usb power is disconnected. I reconnect it - it shows up fine - reads/writes. The drive was not reading/writing when i moved it. Did I damage my drive? Are these things that fragile? I thought them to be at least as durable as a standard 2.5" internal drive. Am I mistaken?

    Read the article

  • Anyone recommend a program to print multiple HTML files at once for end users?

    - by Keith Bentrup
    I have some clients with multiple html files in folders that are occasionally updated & printed. They would like to be able to print them all at once without having to open each one. I typically do this with a quick command for myself, but I'm unaware of any freeware to do this. After a google search, I'm not finding one, so I'm hoping someone can help. I'd rather not use a script to do this for various security/ease of use/familiarity reasons, I'd rather be able to just point to a simple program they can download and use on their windows desktops. Anyone know of one or some other easy solution to do this? Maybe I'm overlooking the obvious. If anyone's curious, this is what I do for myself (not for my clients): for %h in (*.html) do type "%h" >> all.htm then open all.htm & print. If I need a page break on each doc, I just search and replace in all.htm </body> with <p style="page-break-after:always">&nbsp;</p></body>. It's quick & simple, but too unfamiliar for them. Thanks!

    Read the article

  • Why does the Mac OS X firewall dialog recurringly pop-up and disappear by itself (without letting me

    - by Chris W. Rea
    From time to time, I'll be on my Macbook using a program that accesses the network – whether Firefox, or Sony's Reader Library – really, it seems like it could happen with any program that accesses the network – and for no reason that I can discern so far (that is, it happens intermittently) the OS X firewall dialog pops up to ask me the question: Except it doesn't actually let me click anything before it disappears! That is: the dialog pops up, ... then goes away by itself a second later, then pops up again, ... then goes away by itself a second later, etc. It happens a few times before stopping. It wouldn't be so maddening to be interrupted if I could just be allowed to click "Allow" and make the darn thing go away for good. In Security preferences I have the firewall turned "On", and I would like to keep it that way. Has anybody seen this problem, found the source, and figured out a solution or workaround? Thank you.

    Read the article

  • Tunnell network requests with Windows 7

    - by mark
    I've Windows 7 64bit Pro client in a private LAN behind a Netgear wgr614v7 router. I've also a remote Debian server machine outside. I'd like to tunnel all (or specified ports/protocols) over this outside server, so when I'm on the Windows machine and I request serverfault.com it would not appear from the wgr614v7 public IP but from the server. But it's not only about HTTP traffic, it's basically about everything I'd like to: other TCP ports, even UDP, etc. It must be transparent to the application, e.g. they shouldn't be aware of this. All their requests just appear as being from the server and the tunnel between them takes care about the packets. I'm aware of e.g. Putty and forwarding individual ports or using it as a socks proxy, however not many applications to support this and the support in windows itself looks non-existent to me. I might add it should be something "reasonable" easy to set up. I've heard about PPTP but I'm unsure about it's security implications (by design). Should I go for VPN? There seem to be two common solutions for Linux (OpenSwan and StrongSwan), why would I pick the one over the other? I also fear that setting up a VPN might be quite complex, OTOH maybe it's the only sane way to do the things right? Or is OpenVPN sufficient? I'm seeking for open (source) solutions, what other options to I have or which direction should I head to?

    Read the article

  • Windows Server 2008 - Non-Domain users can see my server shares

    - by ManovrareSoft
    Windows Server 2008 - Server Machine Windows 7 Professional - Client Machine I have a domain. It was setup by the client. The shares on the server are restricted correctly when a user logs on to the domain and uses their workstation, I have a few groups setup to restrict some access but the groups are at their core "Domain Users". The problem I am having is that when a user brings in a laptop with Windows 7 Pro on it, they can type up the name of the server in the "Run Dialog" on the start menu like "\SERVERNAME\" and access all of the shares freely... because they are not logged in to the domain there are no restrictions it seems.I have reviewed the permissions on the folders and they all have to be "Domain Users" and I have removed "Everyone" from the list of people able to see it. Guest access is also disabled...What am I doing wrong? Only group in the list is "Domain Users" isn't a domain user a user that is logged in to the domain? How do I stop non-domain users from seeing the shared folder? I noticed this on Windows Server 2003 too at another time. I assume they both had similar security issues and neither were set up by myself so I am not sure what could have been enabled or specifically deactivated that makes this issue appear.

    Read the article

  • Is it safe to format this partition?

    - by xanesis4
    On a ubuntu server I own, I am running out of space. When I ran sudo parted /dev/sda -l to find all available drives, I got this: Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 256MB 255MB primary ext2 boot 2 257MB 1000GB 1000GB extended 5 257MB 1000GB 1000GB logical lvm Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-swap_1: 2135MB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2135MB 2135MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-root: 998GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 998GB 998GB ext4 I understand /dev/mapper/server--vg-root is the filesystem, and /dev/sda1 has some stuff related to GRUB. But, what about /dev/sda2 and /dev/sda5? When I tried to mount /dev/sda2, it said that I needed to specify the file system, which according to the table, is nonexistent. So, is it safe to format this with, say ext4 and mount it? Also, when I tried to mount /dev/sd5, it gave me this error: mount: unknown filesystem type 'LVM2_member' I assume it is NOT save to reformat this. If I'm wrong, then that would be great, because I could save some space. Please let me know either way. Thanks in advance! UPDATE: Here is the result of mount: /dev/mapper/server--vg-root on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /boot type ext2 (rw,acl) /dev/sda1 on /media/hd2 type ext2 (rw)

    Read the article

  • What ports, besides 80, need to be available to send (only send) email using phpmailer to gmail over SSL?

    - by Wobblefoot
    Using phpmailer I keep getting a 110 timeout and "Unable to connect to host" when sending email from my web server. The authentication details are right and they work on another server I have (login, pwd, ports etc and gmail acct set up for SSL connections on 465), but it's failing on my new server. FIREWALL: I allow related/established, port 80 and a port for SSH on INPUT, then this on OUTPUT: 7906 474K DROP tcp -- any any anywhere anywhere tcp dpt:smtp 0 0 ACCEPT tcp -- any any localhost.localdomain yw-in-f109.1e100.net tcp dpt:submission 0 0 ACCEPT tcp -- any any localhost.localdomain gx-in-f109.1e100.net tcp dpt:ssmtp 0 0 DROP tcp -- any any anywhere anywhere tcp dpt:submission 9 540 DROP tcp -- any any anywhere anywhere tcp dpt:ssmtp This output chain works on my other server and disabling it doesn't get mail delivered either. WEB SERVER: Varnish (80) Nginx (8088) Drupal 7 PHP5-FPM APC MySQL All works beautifully, except for outgoing email. What else could it be? I understand phpmailer does NOT require a local MTA or procmail (this is sort of the point - I don't want the security or admin overhead of a full blown MTA on my web server). Am I wrong? Do I need an MTA as well? What local ports and programs are used to authenticate over SSL and route mail using phpmailer? Any ideas at all greatly appreciated - wasted a day on this nonsense already!

    Read the article

  • Debian 7 and PHP 5.4.4 error reporting

    - by milovan
    I use default php.ini and then in my PHP script (local.settings.php in Drupal) I simply set ini_set('error_reporting', 'E_ALL & ~E_NOTICE & ~E_STRICT'); According to documentation this means "show all messages minus notice and strict warnings". But in my case it still shows strict warnings! I have no idea why, because I clearly stated "~E_STRICT". If I comment it out then I see strict warnings. So it means that default from php.ini "E_ALL & ~E_DEPRECATED & ~E_STRICT" didn't do its job as it also has "~E_STRICT" but I still see strict warnings. On Debian 6 there was Suhoshin patch which was controlling usage of php_ini in PHP scripts. Especially when you try to get more memory than defined cap. Now on debian 7 there is no Suhoshin nor any other security element that might control php_ini. So what might cause php_ini not to be executed? Is there some new variable / setup / other that needs to be checked?

    Read the article

  • What Logs / Process Stats to monitor on a Ubuntu FTP server?

    - by Adam Salkin
    I am administering a server with Ubuntu Server which is running pureFTP. So far all is well, but I would like to know what I should be monitoring so that I can spot any potential stability and security issues. I'm not looking for sophisticated software, more an idea of what logs and process statistics are most useful for checking on the health of the system. I'm thinking that I can look at various parameters output from the "ps" command and compare to see if I have things like memory leaks. But I would like to know what experienced admins do. Also, how do I do a disk check so that when I reboot, I don't get a message saying something like "disk not checked for x days, forcing check" which delays the reboot? I assume there is command that I can run as a cron job late at night. How often should it be run? What things should I be looking at to spot intrusion attempts? The only shell access is SSH on a non-standard port through UFW firewall, and I regularly do a grep on auth.log for "Fail" or "Invalid". Is there anything else I should look at? I was logging the firewall (UFW) but I have very few open ports (FTP and SSH on a non standard port) so looking at lists of IP's that have been blocked did not seem useful. Many thanks

    Read the article

  • Where does Firefox store cerificates and how to delete one?

    - by majid4466
    Hi all, The root cause of my problem is not known to me, whatever it is, I experience frequent DNS failures. When it happens I cannot browse to my Gmail inbox. I use two DNS settings. One is the public DNS server offered by OpenDNS, and the other is Google's free DNS server. When this happens I switch from the active setting to the other one and the problem goes away. But there is a side effect to this. When browsing to Gmail fails to load, after switching the DNS I receive an error saying the security certificate the site uses is only valid for OpenDNS. This my wild guess at what is going on: OpenDNS fails to resolve mail.google.com to its IP, My ISP sends me a page showing search results for 'mail.google.com' Since I have received some sort of page instead of a timeout, the browser, mistakenly, binds the certificate it has cached for 'mail.google.com' to the new domain. This search page is not served by https so not exception is thrown by the wrong binding After switching the DNS, the domain is correctly resolved to Gmail server's IP and since his is on https the handshake is triggered. Now, because of the wrong binding, which passed quietly as no handshake was involved, I receive the error saying the certificate used by 'mail.google.com' is only good for openDNS I don't know much about DNS, less about https and the process of establishing a secure connection. How correct is my explanation? How can I delete the wrong association and/or the certificate? Thanks for listening. P. S. The problem goes away by itself, but sometimes it takes several hours before Gmail works again.

    Read the article

  • Where does Firefox store cerificates and how to delete one?

    - by majid4466
    Hi all, The root cause of my problem is not known to me, whatever it is, I experience frequent DNS failures. When it happens I cannot browse to my Gmail inbox. I use two DNS settings. One is the public DNS server offered by OpenDNS, and the other is Google's free DNS server. When this happens I switch from the active setting to the other one and the problem goes away. But there is a side effect to this. When browsing to Gmail fails to load, after switching the DNS I receive an error saying the security certificate the site uses is only valid for OpenDNS. This my wild guess at what is going on: 1. OpenDNS fails to resolve mail.google.com to its IP, 2. My ISP sends me a page showing search results for 'mail.google.com' 3. Since I have received some sort of page instead of a timeout, the browser, mistakenly, binds the certificate it has cached for 'mail.google.com' to the new domain. This search page is not served by https so not exception is thrown by the wrong binding 4. After switching the DNS, the domain is correctly resolved to Gmail server's IP and since his is on https the handshake is triggered. 5. Now, because of the wrong binding, which passed quietly as no handshake was involved, I receive the error saying the certificate used by 'mail.google.com' is only good for openDNS I don't know much about DNS, less about https and the process of establishing a secure connection. How correct is my explanation? How can I delete the wrong association and/or the certificate? Thanks for listening. P. S. The problem goes away by itself, but sometimes it takes several hours before Gmail works again.

    Read the article

  • PPTP VPN on Server 2008 Enterprise

    - by Mike K
    I asked this question on Server fault and was told that was not allowed so im moving it here. I am running Windows Server 2008 enterprise in my HOME network inside of vmware workstation. I am running this on my home network to setup a PPTP VPN connection at home. I have correctly setup everything I needed to make it work, including opening all the ports, 1723 and 43 (GRE). I am able to connect just fine, but when I connect I dont have internet unless I uncheck use remote gateway. The thing is, I want to use the remote gateway to route all my traffic through that connection. Can someone tell me why this isnt working and how to get it to work. When I have remote gateway checked, and I do an ipconfig I dont get a remote gateway for the VPN connection, its 0.0.0.0 when id assume if connected properly should be 192.168.1.254 (my ATT Home Router). Also, if I cant get the remote gateway issue to work, and I have to uncheck that box to get internet, does this mean my VPN session is no longer encrypted? I am fully aware the PPTP VPN is the weakest VPN encryption out there but still having that extra layer of security when im on an unsecure wifi connection makes me feel a bit better. Thank you for all your help in advance. Someone told me I need to setup a gateway or router configured on the server. If thats the case, how go I go about telling the remote co

    Read the article

< Previous Page | 428 429 430 431 432 433 434 435 436 437 438 439  | Next Page >