Search Results

Search found 47491 results on 1900 pages for 'super x man'.

Page 433/1900 | < Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >

  • ignore ipv6 router advertisements for static addresses with bonded interfaces

    - by boran
    I need to attribute static IPv6 addresses (not use autoconfigured addresses, and ignore router advertisements). This can be done as follows for a standard interface like eth0 iface eth0 inet6 static address myprefix:mysubnet::myip gateway myprefix:mysubnet::mygatewayip netmask 64 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.autoconf=0 pre-up /sbin/sysctl -q -w net.ipv6.conf.$IFACE.accept_ra=0 However, how can this be done for bonded interfaces? using the "all" interface does not work. Systems is Ubuntu 10.04, 2.6.24-24-server. If one uses the above sysctl command for the bond0, the networking hangs on boot, because /proc/sys/net/ipv6/conf/bond0 does not yet exist and cannot be written to. One the system has booted /proc/sys/net/ipv6/conf/bond0 exist, so one solution after booting is to add the following to /etc/rc.local: /sbin/sysctl -q -w net.ipv6.conf.bond0.autoconf=0 /sbin/sysctl -q -w net.ipv6.conf.bond0.accept_ra=0 /etc/init.d/networking restart and this has the desired effect, the autoconfig v6 address disappears. Seems like a bit of a hack though, are there better solutions?

    Read the article

  • Help make sense of a KillDisk error/log

    - by user284194
    I have a hard drive that I've been trying to reformat. I tried reformatting it in the windows XP and 7 installers, and in an Ubuntu live cd with gparted. I tried using dd to 'zero' the drive as well with no success. Finally I ran across KillDisk after a search. I tried to zero the disk again with KillDisk and after 8 hours of zeroing I get the following errors in the log: ----------------------------------------Erase Session Begin--------------------------------------- 2010-03-23 19:35:54 Active@ KILLDISK for Windows Build 5.1.39 started Target: WDC WD2500KS-00MJB0 232.9 GB Located on: WDC WD2500KS-00MJB0 (Serial number: WD-WCANK9604799) Erase method: One Pass Zeros (1 pass) Passes: 1 Bad (unwritable) sectors detected from 1701 to 488397167 on Hard Disk 1. Error (the handle is invalid) refreshing device Hard Disk 1. Error (the handle is invalid) reading sector 0 on 81h. 2010-03-24 02:28:25 Total number of erased device(s): 0, partition(s): 0 -----------------------------------------Erase Session End---------------------------------------- Is the drive dead?

    Read the article

  • How can I archive a 30GB file?

    - by Joel Coehoorn
    I have a zip 30GB zip file containing an archive of digital materials available in the school library that I want to burn to dvd. Of course, 30Gb is far too large for a single dvd and the content is already zipped. I'm open to ideas, but leaning towards suggestions that will help me automatically spread the file over multiple dvds, including a simple program to stitch it back together again later.

    Read the article

  • How to add LDAP user to existing local group in RHEL?

    - by Highway of Life
    I'm attempting to add some of our LDAP users to a locally defined group on our RHEL server, however I get an error stating that the LDAP user is not found in /etc/passwd. What would be the best way to allow LDAP users to be added to local groups? My feeling is that this must be done manually. I could edit: /etc/group and add the LDAP group to the list. Would that be ideal? [server]# id apache uid=409(apache) gid=409(apache) groups=409(apache) context=user_u:system_r:unconfined_t:s0 [server]# id john.doe uid=11389(john.doe) gid=6097(ABC_Corporate_US) groups=6097(ABC_Corporate_US) context=user_u:system_r:unconfined_t:s0 [server]# /usr/sbin/usermod -a -G apache john.doe usermod: john.doe not found in /etc/passwd OS: RHEL (Red Hat Enterprise Linux Server release 5.3 (Tikanga)) Note: Updating the OS on this machine is not an option.

    Read the article

  • Can't Install msysgit/tortoisegit

    - by Jay
    I ran msysGit-netinstall-1.7.0.2-preview20100407-2.exe.   (http://code.google.com/p/msysgit/downloads/list) Then I ran TortoiseGit-1.4.4.0-64bit.msi.   (http://code.google.com/p/tortoisegit/downloads/list) msysgit was installed in C:\ TortioseGit appears to have been installed in C:\Program Files\TortoiseGit I have: "Git Clone..." "Git Create repository here" "TortoiseGit" in Explorer context menu. When I try to clone, I get "git have not installed" [sic]. I have tried setting the MSysGit path, in the TortioseGit settings, to everything imaginable. Nothing works. Neither C:\Program Files or C:\Program Files (x86) have a Git folder. The git command gives "command not found" from both cmd.exe and bash (that msysgit installed) I don't not see msysgit in - Control Panel - Programs - Program Features, but I do see TortioseGit in there. I would like a procedure for verifying that msysgit is properly installed. A procedure for uninstalling msysgit would be an added bonus. I would like a procedure for getting TortoiseGit to work. I am running Windows 7 on a MacBook Pro.

    Read the article

  • Install self-signed certificate on local server (iis)

    - by ile
    On this page there are instructions on how to create self-signed cert (on apache) and how to install this certificate on server. I found this page (http://www.visualwin.com/SelfSSL/) with instructions on how to create self-signed certificate on windows (iis). I followed instructions and when I type https://myip/myapp (this leads to localhost because I set my router's port forwarding to go to localhost on my pc) this part works. From the first link, the most important part is this: What needs to be installed in IE is actually the Root CA Certificate. In the how-to above, the Root CA Certificate is called ca.crt. Copy this file to the server that is running QuickBooks. The following is for IE6: - Open IE - Tools - Internet Options - Content - Certificates - Trusted Root Certification Authorities Tab - Import, Next, Browse to 'ca.crt' - Next, Next, Finish, Close, OK The part that is missing in second link is that there is no instruction on how to get .crt file, so I tried to get it myself. What I did was following: I opened https://myip/myapp in Firefox and then "This Connection is Untrusted" screen appeared. Then I clicked on "Add Exception" and then below "Certificate Status" I clicked "View". Under the Details tab I clicked on Export and choosed Save as type: "X 509 Certificate (PEM)" and file was saved with .crt extension. Then I opened IE8 and followed above instructions. After opening https://myip/myapp in IE8 I always get warning screen. Does anyone knows what am I doing wrong? Thanks, Ile

    Read the article

  • Is MozyHome Remote Backup known to slow down Windows Explorer?

    - by Kyle Estes
    Windows Explorer on my home machine is uber slow, and I suspect it is Mozy's fault. In the past Mozy has done some goofy stuff like placing file and folder icon overlays in Windows Explorer, which was really bugging me because I thought they were from TortoiseSVN (and I had uninstalled that!). Anyhow, does anyone else have Mozy installed? Is Windows Explorer really slow respond for you, say when you simply double click the hard drive to browse files? I'd also welcome any tips people might have on debugging why Windows Explorer might be slow (shell extensions known to cause problems, etc.).

    Read the article

  • Display aspect ratio problem on netbooks?

    - by Jian Lin
    Last night in a computer store with the midnight sale of Windows 7, I see many netbooks, all are 1024 x 600 resolution. Then when the CPU meter and the Clock gadget were added, the CPU meter looked spherical, but the clock (the second clock -- the silver one) looked somewhat oval. Later on I went to all the desktops and both the CPU meter and the clock were spherical. So do the netbook have this "aspect ratio" problem? It is not a big deal but it'd be nice to know if I get a netbook and know that it is common on the netbook. (and aware that the picture and photos will be slightly distorted). Update: All the netbooks were at 1024 x 600, which was their "native" resolution. Every single one of them showed an oval shaped clock. None of the desktop had that issue.

    Read the article

  • Using native resolution on external display results in stretched, out of bounds image

    - by Roni Yaniv
    I have an HP min 311 netbook with Windows XP, which I've connected to a Samsung SyncMaster 2043BW display via the supplied analog cable. The external display's native res is 1680x1050, which the netbook's ION GPU supports. I've configured the external display as the single display (no cloning or any such fancy stuff). However, once I set the native res, the image just stretches out. It looks squashed, and it goes outside the monitor's edges. In contrast, lower resolutions manage to stay within the monitor's display edges, though obviously they are skewed in some way (vertically or horizontally). BTW, the only res which seems to be displayed relatively clearly (it's the least blurry) is 1280x720. I tried looking all over the web for an explanation/advice but could not find any. I already played with the settings on the external display itself several times. So either it's not that, or I missed something. Has someone run into this issue? I need help.

    Read the article

  • How do I bridge connections in windows 7?

    - by Wolfgang Haak
    At work, our ISP has gone down, 3 days running. A company next door has kindly provided us with access to their wireless network, and I'd like to get our internal mail server (win 7) to become online via that wireless connection, while being accessible from within the LAN, but I'm struggling with the windows configuration. Our company's LAN subnet (wired interface) sits on 192.168.0. Neighbour's wireless subnet 192.168.1. I've tried bridging the connections but that disconnects the mail server from the Internet connection and the LAN. what do I have to do achieve this networking configuration? Kind regards, Wolfgang

    Read the article

  • How do I uninstall skydrive and IE11 from windows 8.1?

    - by chipperyman573
    Microsoft is shoving IE11 and Skydrive in my face with windows 8.1. You can disable skydrive by going into the registry and disable IE by going into Turn windows features on or off but the thing that microsoft just can't understand is that I don't want skydrive or IE. I want to remove IE and skydrive from my computer. Google told me that I can go to Control Panel - Programs and Features - Installed Updates and uninstall IE from there. However, there isn't an option to do so: What do I do?

    Read the article

  • Cannot remove wireless network profile even though admin account is used

    - by David Karlsson
    On my windows computer which is connected to a company domain. I have problems with the wireless networking. First of all the computer fails to connect. Second of all I cannot remove the network from the list of wireless profiles. The properties window simply claims that "This network is administered by the Administartor Account". I am currently logged in as the local administrator. I have also tried creating a new admin account and still get the same problem when trying to remove the network. My computer has only the microsoft security essentials antivirus and some VMWare+virtual box connections that I can figure might interfere, but disabling realtime protection has not helped me on this. I also cannot delete the virtual network adapters from the control panel / network adapters...

    Read the article

  • TrueCrypt Failing to Decrypt External Hard Drive after changing Enclosures

    - by Anx Ara
    I have a 4TB external hard drive that was previously encrypted using TrueCrypt. The power source on the hard drive enclosure failed, so I had to switch the hard drive itself into a new enclosure. I can no longer decrypt the hard drive using TrueCrypt, as it says my password is wrong. I am certain that I entering the correct password. Additionally, in TrueCrypt, when I try to mount the volume under "Select Device", it shows the following: Harddisk 5: 3.6TB Device\Harddisk5\Partition 1 H: 465GB Whereas before I changed the enclosure it would show: Harddisk 5: 3.6TB Device\Harddisk5\Partition 1 H: 3.6TB I am on a Windows 8 PC and using TrueCrypt 7.1a. How can I get it to decrypt properly?

    Read the article

  • How do I properly configure a ZipInstaller .zic file?

    - by Iszi Rory or Isznti
    As of version 1.20, ZipInstaller is supposed to support the use of a configuration file to customize its installation options. Generally, all the options I want to use are available through the dialog so I really haven't bothered with the configuration file until now. The problem now is that certain tools, such as PsTools from Sysinternals, do not properly show their Product Name to ZipInstaller. ZipInstaller's dialog will let you customize the Start Menu folder and Program Files folder, but that still doesn't change the Product Name that it sees for the software. So, instead of having "PsTools" in my Add/Remove Programs, I get "Sysinternals Software". For some things, the situation is even more confusing. For example, the NIST SP 800-53 Reference Database Application gets installed as "FileMaker Pro Runtime". To rectify this, I've tried to use the aforementioned .zic configuration file. As I understand it, it's a basic INI file you create and put in the root of the ZIP file. ZipInstaller is supposed to read that file, and adjust its parameters accordingly. Mine looks like this: [install] ProductName=NIST_SP_800-53 ProductVersion=1.4.1 CompanyName=NIST Description=NIST_SP_800-53 InstallFolder=%zi.ProgramFiles%\%zi.ProductName% StartMenuFolder=%zi.CompanyName%\%zi.ProductName% I've named it `~zipinst~.zic and placed it in the root of the ZIP file, but when I run ZipInstaller it doesn't seem to recognize any of the information I've given it in the .zic file. What might I be doing wrong here?

    Read the article

  • Looking for a AutoZoom browser plugin

    - by AngryHacker
    I have a pretty large 24" wide screen with a pretty high resolution. When I browse, some sites have a fixed layout and there is basically a narrow column. So I typically zoom in to the point just before the level where I have to scroll horizontally. Is there a browser plugin that auto-zooms in (or via a button or gesture or whatever) to the max available real estate? I'd prefer a plugin for Chrome, but Firefox will do too.

    Read the article

  • Windows 7 Goes to Sleep in conflict with Power Option Setting

    - by Decker
    My Del Dimension E521 running Windows 7 puts itself in sleep mode each night -- despite the fact that I have chosen a power option that specifies NEVER Each morning I find the monitor blank and I have to hit the power button on the PC at which point Windows "resumes". The system event log shows this: Source: Microsoft-Windows-Kernel-Power Date: 3/27/2010 3:21:10 AM Description: The system is entering sleep. Sleep Reason: System Idle My specific power options are: Turn off Display : 20 Minutes Put the computer to sleep : Never Is there some other setting coming into play here?

    Read the article

  • Share Truecrypt container

    - by uwe
    Hello, is it possible to put a truecrypt container on a net share and access/mount it form multiple machines (windows) at the same time? I fear that if both would write the file could be corrupted.

    Read the article

  • Top/left edges of screen, in Virtualbox, act like bottom/right edges

    - by Ken
    I have Virtualbox running on Windows Vista, and Debian running inside Virtualbox. Everything's running great, for the most part. Everything looks correct. But when I'm in full-screen mode, the top edge seems to act (to the mouse) like it's the bottom edge, and the left edge seems to act like the right edge. For example, if I click in the middle of the desktop and drag left, as if to select some icons, when I hit the very leftmost pixel of the screen, the selection (but not the mouse pointer) jumps to the far right edge of the screen). For the left edge, it's not such a big deal, but not having the top edge is kind of annoying: it means I can't select things from the menu in my top panel by slamming the mouse against the top of the screen. Anyone seen this before? Is there some way to make this work? Thanks!

    Read the article

< Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >