Search Results

Search found 75615 results on 3025 pages for 'www data'.

Page 433/3025 | < Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >

• Recovering data from failed Raid configuration with 4 drives and two raid sets (Asus P6T / Intel ICH10r)

  - by user56365

  I've added the complete detailed version for my question below for those who can help, but want to quickly summarize my question first. I setup two Raid arrays using (4) WD Raptors, a striped set for the OS and 1+0 set for crucial data. After booting once out of the 50 times a cable fell out, the drive wasn't recognized in the array anymore. After trying to fix it, another drive did the same. I now have two drives remaining, luckily with the parity information. I know the striped set is gone, but I need the data on the other set. Can anyone recommend anything to recover the data, or fix the two drives that doesn't allow the raid controller to recognize the drives, even though they are listed on the utility screen as still apart of the configuration but that they are not found? More Details I recently upgraded to a ASUS P6T motherboard with an Intel ICH10R raid controller and changed my previous 4 drive raid array from strictly a Raid 1+0 set to a Raid 0 for the OS/Page/Scratch drive and a Raid 1+0 set for crucial data. I never had problems after upgrading with my configuration, even when a drive died and was replaced. I managed to rebuild the array fine. Unfortunately this time around, a cable came unattached and I booted my system up until the raid status screen with the degraded error. This shouldn't have been a problem, but after I attached the drive it was no longer recognized as a member in the array. Both drives actually show up as a non-member disk. I've spent a very, very long time online trying to find information or support and haven't had much luck. After spending time trying to scan the drive for errors, damaged partition info, etc.. another drive in the set decided it didn't want to be recognized as a part of the array. At this point, I have two out of the four drives still functioning, but the Raid 1+0 array went from degraded to failed and I must find a way to retrieve that data. I think the two drives still in the array have the parity information because they show up as OS (110GB),BACKUP(80GB) and OS:1(110GB),BACKUP(80GB) under windows data management. The other two are simply 74gb Raw unallocated Is it possible recover the data using those two drive only, and which tool would I use? Could it be a simple partition table or any other error that is repairable with hard drive utilities out there? I know the Raid 0 set is done for, but I would assume because the correct drives failed in a 1+0 config to save the data I can retrieve it some how.

  Read the article

• public_html permissions for local development

  - by maGz

  I know this question has popped up a couple times, but I can't seem to find a definitive answer to my issue, so please bear with me. I have Ubuntu Server 12.04 setup in VirtualBox for PHP development and testing (Drupal plus other PHP sites using Yii framework). My question is in 3 parts... 1) If I create a public_html folder under /home/myuser, do I need to give ownership of that folder to the Apache www-data group? If so, are there any specific permissions I should be setting? 755? (Btw, I am following this guide to create the public_html directory and set up multiple virtual hosts per site I create and test) I previously had all of my sites under /var/www, but ran into massive permission denied errors whenever I tried to sFTP to it, either through FileZilla or PhpStorm. This is what I had previously done: sudo chgrp www-data /var/www sudo chmod -R 775 /var/www sudo chmod -R g+s /var/www sudo usermod -G www-data [my_ftp_user] 2) The second part of my question is this: If I create my PHP project and files in Windows through PhpStorm, and then upload via sFTP, will permissions get affected? 3) Once I am satisfied with my developed project, would it be advisable to move and test them under /var/www to see how it would fair in a production-ish environment? I would really appreciate the help and advice here. I'm learning more as I go along, but dealing with Linux files and permissions is a bit of a new ballgame for me! Thank you

  Read the article

• OpenWorld 2011 Video Index

  - by Chris Kawalek

  We did quite a few virtualization videos this year at Oracle OpenWorld 2011. You can find all these and more on our YouTube channel. Virtualization Wrapup Adam Hawley discusses the Oracle virtualization presence at Oracle OpenWorld 2011. http://www.youtube.com/oraclevirtualization#p/f/2/53_SQYljqN4 Oracle Applications on iPad Brad Lackey shows how you can access Oracle Applications on iPad. http://www.youtube.com/oraclevirtualization#p/f/9/3Ug5km3uxEQ Thinkquest.org and Oracle VM Dan Herrup describes how Thinkquest.org is using Oracle VM to help kids learn how to solve real world problems with computer technology. http://www.youtube.com/oraclevirtualization#p/f/6/Bw-km5kqzEo Avaya and Oracle Virtualization See Oracle desktop virtualization in action at Avaya's booth. http://www.youtube.com/oraclevirtualization#p/f/4/xIHRIijEPkM Eco-Features of Sun Ray Clients Michael Dann shows off the Sun Ray 3 Plus and talks about the eco benefits of Oracle's extremely low power consumption client device for desktop virtualization. http://www.youtube.com/oraclevirtualization#p/f/3/ulArHGe1OmM Application and Desktop Access with Oracle Secure Global Desktop Watch Jeff Harvey do a quick demo of Oracle Secure Global Desktop accessing Oracle Applications. http://www.youtube.com/oraclevirtualization#p/f/5/g_ikA7dwh0g Oracle VM VirtualBox for VDI Andy Hall describes how enterprises leverage Oracle VM VirtualBox as part of their VDI deployments. http://www.youtube.com/oraclevirtualization#p/f/8/WmkeYlzgnZ8 TechCast Live: The Coolest Virtualization Products Interview with Andy Hall about the desktop virtualization portfolio. http://www.youtube.com/oraclevirtualization#p/f/7/VMkrAhZ83AA

  Read the article

• Cannot access new folders created in my Apache2 document-root

  - by user235101

  I have tried to create a new folder 'test' in my documentroot of my Apache2 installation, however, whenever I try and access it from a web-browser it gives me a 403 (forbidden) error. My virtualhosts file - <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName REMOVED DocumentRoot /var/www/ <Directory /> Options FollowSymLinks AllowOverride All AuthType Digest AuthName "documentroot" AuthDigestProvider file AuthUserFile /etc/apache2/htpasswd Require user REMOVED AllowOverride Indexes </Directory> <Directory /var/www/> Options FollowSymLinks Options -Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> <Directory /var/www/share/> Order Deny,Allow Allow from all Satisfy any </Directory> <Directory /var/www/REMOVED/> Order Deny,Allow Allow from all Satisfy any </Directory> <Directory /var/www/stream/> Order Deny,Allow Allow from all Satisfy any </Directory> <Directory /var/www/test> Order Deny,Allow Allow from all Satisfy any </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined <Directory /var/www/REMOVED> AuthType Digest AuthName "rutorrent" AuthDigestDomain /var/www/REMOVED/ http://46.105.127.19/REMOVED AuthDigestProvider file AuthUserFile /etc/apache2/htpasswd Require valid-user SetEnv R_ENV "/var/www/REMOVED" AllowOverride Indexes </Directory> </VirtualHost> Image of the permissions - Other information - If I create a new folder (and use chmod --reference to ensure it has the same permissions as an accessible folder), I get a 403 client-side. If I copy folder 'rapidleech' to the name 'rapidleech1', it will let access 'rapidleech1', but no longer 'rapidleech', until I delete the copy. In my logs I found nothing logged in errors.log, and only that it delivered a 403 in access.log. All the appropriate users are members of www-data.

  Read the article

• When does Information become Data? (i.e. Information wants to be free) [closed]

  - by James P. Wright

  I hear Programmers often talk about how Information Wants To Be Free which I mostly agree with, but the thing that people don't often pay attention to is that Information and Data are not the same thing. Should Data also be free? Does that mean all of you should have full access to my Social Security Number and other personal "information"? Where is the limit? If there is a limit, why do people throw this phrase around like it fits every circumstance (like this one)

  Read the article

• Google ou le data warehouse mondial : Partage de connaissance ou possession du marché mondiale ?

  Google ou le data warehouse mondiale Partage de connaissance ou possession du marché mondiale ? Google a annoncé la mise en ligne de données supplémentaires nommé World Bank sur son outil public data explorer Via cet outil, vous trouvez toutes les informations mondiales concernant l'agriculture, la consommation électrique par capital, l'émission de CO2 par capital, le nombre d'utilisateurs d'internet,... Ainsi, vous avez par différents graphiques, des statistiques sur toutes les capitales dont vous pourrez comparer les différentes informations propres à ...

  Read the article

• Request Removal of naked domain from Google Index

  - by Pedr

  I have a site which was temporarily available at both example.com and www.example.com. All traffic to example.com is now redirected to www.example.com, however during the brief period that the site was available at the naked domain, Google indexed it. So Google now has two versions of every page indexed: www.example.com www.example.com/about_us www.example.com/products/something ... and example.com example.com/about_us example.com/products/something ... For obvious reasons, this is a bad situation, so how can I best resolve it? Should I request removal of these pages from the index? There is still content at these URLs, but they now redirect to the www subdomain equivalent. The site has many hundreds of pages, but the only way I can see to request removal is via the Remove outdated content screen in Webmaster Tools, one URL at a time. How can I request removal of an entire domain (ie. the naked domain) without it effecting the true site located at the www subdomain? Is this the correct strategy given that all the naked domains now redirect to their www equivalent?

  Read the article

• passenger and apache memory usage

  - by Brent Faulkner

  On a "CentOS release 6.2 (Final)" server (with Ruby 1.9.3 and Rails 3.2), and using more memory than expected. Looking at passenger-memory-stats I see a couple of HUGE httpd processes... any thoughts on how I can figure out what's going on and reduce the memory usage? Stats are included here... thanks! ---------- Apache processes ----------- PID PPID VMSize Private Name --------------------------------------- 1371 1 202.1 MB 0.1 MB /usr/sbin/httpd 4573 1371 210.2 MB 5.0 MB /usr/sbin/httpd 4778 1371 202.5 MB 0.6 MB /usr/sbin/httpd 4780 1371 217.6 MB 9.4 MB /usr/sbin/httpd 4781 1371 217.1 MB 9.1 MB /usr/sbin/httpd 4856 1371 202.4 MB 0.5 MB /usr/sbin/httpd 4863 1371 204.1 MB 2.1 MB /usr/sbin/httpd 5027 1371 202.4 MB 0.5 MB /usr/sbin/httpd 5043 1371 202.4 MB 0.4 MB /usr/sbin/httpd 5044 1371 205.5 MB 2.7 MB /usr/sbin/httpd 5072 1371 202.4 MB 0.5 MB /usr/sbin/httpd 5084 1371 202.4 MB 0.5 MB /usr/sbin/httpd 32111 1371 1297.0 MB 246.5 MB /usr/sbin/httpd 32579 1371 1914.3 MB 215.5 MB /usr/sbin/httpd ### Processes: 14 ### Total private dirty RSS: 493.42 MB -------- Nginx processes -------- ### Processes: 0 ### Total private dirty RSS: 0.00 MB ----- Passenger processes ----- PID VMSize Private Name ------------------------------- 4180 280.5 MB 24.4 MB Passenger ApplicationSpawner: /var/www/apps/people/current 4345 309.5 MB 53.4 MB Rack: /var/www/apps/people/current 4800 300.2 MB 55.2 MB Rack: /var/www/apps/people/current 4808 297.8 MB 52.5 MB Rack: /var/www/apps/people/current 4815 297.4 MB 52.4 MB Rack: /var/www/apps/people/current 4822 302.7 MB 55.6 MB Rack: /var/www/apps/people/current 22780 209.0 MB 0.0 MB PassengerWatchdog 22783 991.5 MB 1.3 MB PassengerHelperAgent 22785 113.4 MB 1.1 MB Passenger spawn server 22788 144.6 MB 0.0 MB PassengerLoggingAgent 22911 310.4 MB 64.0 MB Rack: /var/www/apps/people/current 22939 311.6 MB 53.5 MB Rack: /var/www/apps/people/current 26175 304.1 MB 55.8 MB Rack: /var/www/apps/people/current 26182 310.4 MB 44.0 MB Rack: /var/www/apps/people/current ### Processes: 14 ### Total private dirty RSS: 513.24 MB

  Read the article

• ProxyPass for specific vhost

  - by Steve Robbins

  I have a web server that it set up to dynamically server different document roots for different domains <VirtualHost *:80> <IfModule mod_rewrite.c> # Stage sites :: www.[document root].server.company.com => /home/www/[document root] RewriteCond %{HTTP_HOST} ^www\.[^.]+\.server\.company\.com$ RewriteRule ^(.+) %{HTTP_HOST}$1 [C] RewriteRule ^www\.([^.]+)\.server\.company\.com(.*) /home/www/$1/$2 [L] </IfModule> </VirtualHost> This makes it so that www.foo.server.company.com will serve the document root of server.company.com:/home/www/foo/ For one of these sites, I need to add a ProxyPass, but I only want it to be applied to that one site. I tried something like <VirtualHost *:80> <Directory /home/www/foo> UseCanonicalName Off ProxyPreserveHost On ProxyRequests Off ProxyPass /services http://www-test.foo.com/services ProxyPassReverse /services http://www-test.foo.com/services </Directory> </VirtualHost> But then I get these errors ProxyPreserveHost not allowed here ProxyPass|ProxyPassMatch can not have a path when defined in a location. How can I set up a ProxyPass for a single virtual host?

  Read the article

• Apache forwarding to tomcat shows a blank page

  - by MNS

  I have an application running on tomcat at http ://www.example.com:9090/mycontext. The host name in server.xml points to www .example.com. I do not have localhost anymore. I am using apache to forward requests to tomcat using mod_proxy. Things work fine as long as the ProxyPath is /mycontext. The server name setup in virtual host is www .abc.com and http ://www.abc.com/mycontext works fine. However I would like to ignore the context path and simply use http://www.abc.com/ to forward requests to http://www.example.com:9090/mycontext. When I do this, apache shows me a blank page. What am I missing here? I have not changed anything in server.xml except the default host to www .example.com. <VirtualHost *:80> ServerName www.abc.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://www.example.com:9090/mycontext ProxyPassReverse / http://www.example.com:9090/mycontext </VirtualHost> Thanks

  Read the article

• Website latency and bad tcp packets

  - by Mistero Lupo

  I have multiple websites hosted on a Linode VPS and I'm having an issue with one of them: every page that I try to load has about 10 seconds latency. Apache logs are clean and the other websites on the same machine are running well. At a first glance I tought it was a memory problem since the VPS has got only 512M, but from the linode dashboard CPU and Disk I/O are normal. Anyway here we have the ram status: $ free -m total used free shared buffers cached Mem: 487 463 23 0 2 55 -/+ buffers/cache: 404 82 Swap: 255 155 100 Only 23M free, but if it was a memory problem why other websites are going as usual? I took a live capture with wireshark, and there are some duplicates SYN ACK packets just before the 10 seconds gap. I'm out of ideas, looking for some clues. Wireshark live capture screenshot As you can see from the image, the gap is after the last bad tcp. Thank you in advance. UPDATE I've checked Apache2 logs in debug error level, and this is where something is appening: 151.97.156.191 - - [14/Nov/2012:11:19:40 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6801578/subreq] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] applying pattern '^index\.php$' to uri 'index.php' 151.97.156.191 - - [14/Nov/2012:11:19:40 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6801578/subreq] (1) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] pass through /home/fmaisi/sites/www.fmaisi.it/public_html/index.php 151.97.156.191 - - [14/Nov/2012:11:19:54 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6537c78/initial] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] strip per-dir prefix: /home/fmaisi/sites/www.fmaisi.it/public_html/wp-content/plugins/wp-filebase/wp-filebase_css.php -> wp-content/plugins/wp-filebase/wp-filebase_css.php 151.97.156.191 - - [14/Nov/2012:11:19:54 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6537c78/initial] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] applying pattern '^index\.php$' to uri 'wp-content/plugins/wp-filebase/wp-filebase_css.php' As you can see there is a gap of 14 seconds after the pass through of index.php. Any suggestions? I'm out of ideas again.

  Read the article

• Apache has many PHP session files

  - by PiTheNumber

  # ls /var/lib/php5 | wc -l 7488 # ls -la -rw------- 1 wwwrun www 0 Nov 9 15:30 sess_vtuh671rlafdidfjmgjfu6065p4tfieg -rw------- 1 wwwrun www 0 Nov 12 02:30 sess_vu9pn476oiqbsd20q4s2brt60b9vg90d -rw------- 1 wwwrun www 0 Nov 9 15:07 sess_vuonfs2cqsdiq8ja51ornh6lp5j9mf93 -rw------- 1 wwwrun www 0 Nov 9 16:02 sess_vuutcad8as55il34db3uqhqrsltd4q6o -rw------- 1 wwwrun www 0 Nov 9 23:26 sess_vv2mrv5dnlnts6das4g5jlfldael4l0e -rw------- 1 wwwrun www 44 Nov 9 20:35 sess_vvc0cfjuvk3lqb5m97fv6gsmv6bjhsdk -rw------- 1 wwwrun www 0 Nov 9 10:33 sess_vvq82fhj9lg29gaejemlb2lrk25mqv7d -rw------- 1 wwwrun www 0 Nov 9 20:36 sess_vvtd4ka8rfmcroa34unl06916ubj8sb9 Most of them are empty. There are not so many users on the server so I wonder where those files came from. Is this a problem or how does apache handle those file? Do they get delete automaticly? Could this be caused by a bad PHP file?

  Read the article

• apache subdomain configuration

  - by terrid25

  I seem to be having a small problem with setting up a subdomain in apache under CentOS. I have the following: <VirtualHost *:80> ServerName www.domain.co.uk ServerAlias domain.co.uk dev.domain.co.uk DocumentRoot "/var/www/html/domain/web" DirectoryIndex index.php Alias /sf /var/www/html/symfony14/web/sf <Directory "/var/www/html/domain/web"> AllowOverride All Allow from All </Directory> </VirtualHost> <Directory "/var/www/html/symfony14/web/sf"> AllowOverride All Allow from All </Directory> <VirtualHost *:80> ServerName test.domain.co.uk DocumentRoot "/var/www/html/domain_test/web" DirectoryIndex index.php Alias /sf /var/www/html/symfony14/web/sf <Directory "/var/www/html/domain_test/web"> AllowOverride All Allow from All </Directory> </VirtualHost> So going to www.domain.co.uk and domain.co.uk display the contents from /var/www/html/domain, but going to test.domain.co.uk also displays the same folder contents. Is this because of the ServerAlias ? Thanks

  Read the article

• Remove folder structure from archive, ignore folder while archiving and fix error

  - by Michael

  I am trying to make a script to backup each of my plesk hosts to individual files, I am having two problems: I would like to remove the folder structure from archive, the tar is 3 folders deep I am getting this error: tar: Removing leading `/' from member names I need my archive to ignore folders named "catch" because I don't need them in my archive. The code: FILES=/var/www/vhosts/* FNAME="" for f in $FILES do FNAME=`basename $f` tar cfv "/root/backup/ftp/$FNAME.tar" $f done Sample output: tar: Removing leading `/' from member names /var/www/vhosts/mydomain.com/ /var/www/vhosts/mydomain.com/conf /var/www/vhosts/mydomain.com/etc/ /var/www/vhosts/mydomain.com/etc/group /var/www/vhosts/mydomain.com/etc/termcap /var/www/vhosts/mydomain.com/etc/passwd /var/www/vhosts/mydomain.com/usr/

  Read the article

• Facebook sort Presto, son moteur de requêtes open source pour le big data, qui serait dix fois plus performant que celui de Hadoop

  Facebook sort Presto, son moteur de requêtes open source pour le big data qui serait dix fois plus performant que celui de HadoopDe nombreuses entreprises comme Facebook dépendent du Big data. Dans le domaine, on compte la paire Hadoop/Hive parmi les références. Pour rappel, Hive c'est le moteur de requêtes populaire pour Hadoop. Cependant, il se pourrait que le MapReduce élément essentiel sur lequel repose Hive ne soit pas optimisé pour des situations ou la quantité de données excède un certain...

  Read the article

• nginx redirects and rewrites

  - by ptheofan

  I'm closing a website but want to maintain a couple of urls working plus a static html file to serve as index. All old urls should redirect to root (/) except a couple of chosen locations. Here's an example of what I need to do All should give 301 permanent to / http:://www.domain.tld/whatever/anything/realy == 301 ==> http://www.domain.tld http:://www.domain.tld/blabla == 301 ==> http://www.domain.tld http:://www.domain.tld/ == 301 ==> http://www.domain.tld except for http://www.domain.tld/special.html == serve ==> special.html root should serve the defailt file (as specificed in index) http:://www.domain.tld == serve => somefile.html

  Read the article

• Nginx vhost configuration

  - by user101494

  I am attempting to setup a new server with Nginx 1.0.10 on debian 6. The config below works perfectly on a server with nginx 0.8.36 on Ubuntu 10.04.3 but not on the new box. The desired result is to: Redirect non-www request on the tld to www, but not not subdomains Use the the folder structure /var/www/[domain]/htdocs /var/www/[domain]/subdomains/[subdomain]/htdocs Serve files any host for which files exist in this structure On the new server domains are matching correctly but subdomains are matching to /var/www/[subdomain].[domain]/htdocs not /var/www/[domain]/subdomains/[subdomain]/htdocs server { listen 80; server_name _________ ~^[^.]+\.[^.]+$; rewrite ^(.*)$ $scheme://www.$host$1 permanent; } server { listen 80; server_name _ ~^www\.(?<domain>.+)$; server_name_in_redirect off; location / { root /var/www/$domain/htdocs; index index.html index.htm index.php; fastcgi_index index.php; } location ~ \.php$ { include /etc/nginx/fastcgi_params; keepalive_timeout 0; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } location ~ /\.ht { deny all; } } server { listen 80; server_name __ ~^(?<subdomain>\.)?(?<domain>.+)$$; server_name_in_redirect off; location / { root /var/www/$domain/subdomains/$subdomain/htdocs; index index.html index.htm index.php; fastcgi_index index.php; } location ~ \.php$ { include /etc/nginx/fastcgi_params; keepalive_timeout 0; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } location ~ /\.ht { deny all; } }

  Read the article

• RewriteMap syntax Regex

  - by ienabellamy

  in my .htaccess i've tons of directives, with same syntax: RewriteRule ^(.*)/PRODUCT_1.aspx http://www.site.com/product.php?id_product=2891 RewriteRule ^(.*)/PRODUCT_2.aspx http://www.site.com/product.php?id_product=2896 and everything works. Now, i created a RewriteMap in my because i need to increase velocity (20.000 redirect 301 in htaccess no good), so: RewriteEngine On RewriteMap redirects dbm=db:/var/www/html/presta152/prestashop/redirects.db RewriteCond ${redirects:$1} !="" RewriteRule ^(.*)$ ${redirects:$1} [redirect=permanent,last] and my redirects.db is created by redirects.txt, that contains: /PRODUCT_1.aspx http://www.site.com/product.php?id_product=2891 /PRODUCT_2.aspx http://www.site.com/product.php?id_product=2896 this works if i try to call for example: www.site.com/PRODUCT_1.aspx i'm redirected... but if i try to call www.site.com/everythingpossibileinside/PRODUCT_1.aspx the redirect doesn't work. So, in my .htaccess this rule: RewriteRule ^(.*)/PRODUCT_1.aspx http://www.site.com/product.php?id_product=2891 works, but in my RewriteMap no. I think i must change this directive: RewriteRule ^(.*)$ ${redirects:$1} [redirect=permanent,last] i tried, but unsuccessful. Thanks to all.

  Read the article

• Ubuntu 10.04 Apache Configuration for Websites

  - by completenoob

  Looking at a basic Ubuntu 10.04 server setup, Apache points to /var/www for where to it looks for files to serve up. The default apache user is www. I'm just trying to set up a plain old WordPress blog. Should I just dump the files into /var/www/ as root or www? User www seems inconvenient since I won't log in as the user, but I guess I can chown the files in /var/www to www. Not that I would log in as root either, but what is the recommended user who should own the /var/www files? Thanks for the help.

  Read the article

• Les Bouches-du-Rhône sponsorisent des développeurs pour promouvoir l'open data : avez-vous proposé votre application ?

  Les Bouches-du-Rhône lancent une opération de sponsoring pour les développeurs d'applications et de sites web Afin de promouvoir l'open-data et la région, Developpez.com partenaire Depuis le mois d'avril, l'association Bouches-du-Rhône Tourisme a rejoint la démarche Open-data en ouvrant son portail et en libérant une centaine de jeux de données liées au tourisme dans le département. Toutes les informations détenues par l'association ont été rendues disponibles et exploitables par les développeurs, les scientifiques, les associations, les étudiants et les entreprises. Bref, par tout le monde. On y trouve par exemple...

  Read the article

• Windows Server 2003 - Are ODBC Data Source's set per-user?

  - by Jakobud

  When I'm logged into our Windows Server 2003 server, I don't see any ODBC Data Sources, but when a different user logs in (who doesn't have Administrative rights), they have a big list of ODBC Data Sources. Are ODBC Data Sources set on a per-user basis? How come the Administrator can't see user's ODBC Data Sources?

  Read the article

• Les Bouches-du-Rhône lancent une opération de sponsoring de développeurs pour promouvoir l'open-data et la région

  Les Bouches-du-Rhône lancent une opération de sponsoring pour les développeurs d'applications et de sites web Afin de promouvoir l'open-data et la région, Developpez.com partenaire Depuis le mois d'avril, l'association Bouches-du-Rhône Tourisme a rejoint la démarche Open-data en ouvrant son portail et en libérant une centaine de jeux de données liées au tourisme dans le département. Toutes les informations détenues par l'association ont été rendues disponibles et exploitables par les développeurs, les scientifiques, les associations, les étudiants et les entreprises. Bref, par tout le monde. On y trouve par...

  Read the article

• Redirect traffic to https

  - by Arpanet

  I need to redirect the following instances to https://www.mydomain.com; mydomain.com www.mydomain.com http://www.mydomain.com I have the following in my .htaccess already, but this only redirects mydomain.com to https://www.mydomain.com; <IfModule mod_rewrite.c> RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} !^www\..+$ [NC] RewriteRule ^ https://www.%{HTTP_HOST}%{REQUEST_URI} [R=301,L] </IfModule> Grateful if anyone could perhaps tell me what I need to add. Thank you.

  Read the article

• Should I be relying on WebTests for data validation?

  - by Alexander Kahoun

  I have a suite of web tests created for a web service. I use it for testing a particular input method that updates a SQL Database. The web service doesn't have a way to retrieve the data, that's not its purpose, only to update it. I have a validator that validates the response XML that the web service generates for each request. All that works fine. It was suggested by a teammate that I add data validation so that I check the database to see the data after the initial response validator runs and compare it with what was in the input request. We have a number of services and libraries that are separate from the web service I'm testing that I can use to get the data and compare it. The problem is that when I run the web test the data validation always fails even when the request succeeds. I've tried putting the thread to sleep between the response validation and the data validation but to no avail; It always gets the data from before the response validation. I can set a break point and visually see that the data has been updated in the DB, funny thing is when I step through it in debug with the breakpoint it does validate successfully. Before I get too much more into this issue I have to ask; Is this the purpose of web tests? Should I be able to validate data through service calls in this manner or am I asking too much of a web test and the response validation is as far as I should go?

  Read the article

• Am I correctly extracting JPEG binary data from this mysqldump?

  - by Glenn

  I have a very old .sql backup of a vbulletin site that I ran around 8 years ago. I am trying to see the file attachments that are stored in the DB. The script below extracts them all and is verified to be JPEG by hex dumping and checking the SOI (start of image) and EOI (end of image) bytes (FFD8 and FFD9, respectively) according to the JPEG wiki page. But when I try to open them with evince, I get this message "Error interpreting JPEG image file (JPEG datastream contains no image)" What could be going on here? Some background info: sqldump is around 8 years old vbulletin 2.x was the software that stored the info most likely php 4 was used most likely mysql 4.0, possibly even 3.x the column datatype these attachments are stored in is mediumtext My Python 3.1 script: #!/usr/bin/env python3.1 import re trim_l = re.compile(b"""^INSERT INTO attachment VALUES\('\d+', '\d+', '\d+', '(.+)""") trim_r = re.compile(b"""(.+)', '\d+', '\d+'\);$""") extractor = re.compile(b"""^(.*(?:\.jpe?g|\.gif|\.bmp))', '(.+)$""") with open('attachments.sql', 'rb') as fh: for line in fh: data = trim_l.findall(line)[0] data = trim_r.findall(data)[0] data = extractor.findall(data) if data: name, data = data[0] try: filename = 'files/%s' % str(name, 'UTF-8') ah = open(filename, 'wb') ah.write(data) except UnicodeDecodeError: continue finally: ah.close() fh.close() update The JPEG wiki page says FF bytes are section markers, with the next byte indicating the section type. I see some that are not listed in the wiki page (specifically, I see a lot of 5C bytes, so FF5C). But the list is of "common markers" so I'm trying to find a more complete list. Any guidance here would also be appreciated.

  Read the article

< Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >