Search Results

Search found 11608 results on 465 pages for 'usb extension'.

Page 434/465 | < Previous Page | 430 431 432 433 434 435 436 437 438 439 440 441  | Next Page >

  • Linux software RAID6: 3 drives offline - how to force online?

    - by Ole Tange
    This is similar to 3 drives fell out of Raid6 mdadm - rebuilding? except that it is not due to a failing cable. Instead the 3rd drive fell offline during rebuild of another drive. The drive failed with: kernel: end_request: I/O error, dev sdc, sector 293732432 kernel: md/raid:md0: read error not correctable (sector 293734224 on sdc). After rebooting both these sectors and the sectors around them are fine. This leads me to believe the error is intermittent and thus the device simply took too long to error correct the sector and remap it. I expect that no data was written to the RAID after it failed. Therefore I hope that if I can kick the last failing device online that the RAID is fine and that the xfs_filesystem is OK, maybe with a few missing recent files. Taking a backup of the disks in the RAID takes 24 hours, so I would prefer that the solution works the first time. I have therefore set up a test scenario: export PRE=3 parallel dd if=/dev/zero of=/tmp/raid${PRE}{} bs=1k count=1000k ::: 1 2 3 4 5 parallel mknod /dev/loop${PRE}{} b 7 ${PRE}{} \; losetup /dev/loop${PRE}{} /tmp/raid${PRE}{} ::: 1 2 3 4 5 mdadm --create /dev/md$PRE -c 4096 --level=6 --raid-devices=5 /dev/loop${PRE}[12345] cat /proc/mdstat mkfs.xfs -f /dev/md$PRE mkdir -p /mnt/disk2 umount -l /mnt/disk2 mount /dev/md$PRE /mnt/disk2 seq 1000 | parallel -j1 mkdir -p /mnt/disk2/{}\;cp /bin/* /mnt/disk2/{}\;sleep 0.5 & mdadm --fail /dev/md$PRE /dev/loop${PRE}3 /dev/loop${PRE}4 cat /proc/mdstat # Assume reboot so no process is using the dir kill %1; sync & kill %1; sync & # Force fail one too many mdadm --fail /dev/md$PRE /dev/loop${PRE}1 parallel --tag -k mdadm -E ::: /dev/loop${PRE}? | grep Upda # loop 2,5 are newest. loop1 almost newest => force add loop1 Next step is to add loop1 back - and this is where I am stuck. After that do a xfs-consistency check. When that works, check that the solution also works on real devices (such a 4 USB sticks).

    Read the article

  • How to install RAID drivers on already installed Windows 7?

    - by happysencha
    64-bit Windows 7 Ultimate 6GB RAM Intel i7 920 Intel X25-M SSD 80GB 2,5" Club 3D Radeon HD5750 GA-EX58-UD4P Motherboard I've been running fine with Windows 7 installed on the SSD. I wanted to create an mirrored Raid-1 setup for backups using two hard disks, so I ordered two Samsung HD203WI. This motherboard supports two different RAID controllers, the Intel's ICH10R and Gigabyte's SATA2 SATA controller. There are 6 SATA ports behind the ICH10R and 2 SATA ports for the Gigabyte controller. I googled around and seemed that the ICH10R is a better choice and since then I've been trying to make it work. When I activate the [RAID] mode from BIOS, the Windows 7 gives BSOD exactly as described by this guy: "Windows 7 will start to boot, it gets to the screen where there are 4 colors coming together and it blue screens and restarts no matter what I do." First thing I did: turned off the RAID and booted to Windows and tried to install the SATA RAID drivers from Gigabyte. I launch the driver installation program and it gives "This computer does not meet the minimum requirements for installing the software" error. I then tried Intel's Rapid Storage Technology drivers (which apparently is the same as the one offered at Gigabyte's site), but it resulted in exactly the same error. I then detached the new Samsung hard disks from the SATA ports, but left the [RAID] enabled in BIOS. To my surprise, it still BSOD'd, so at this point I knew it is an OS/driver issue. Also, I tried with the Gigabyte's RAID enabled (while the ICH10R RAID disabled) and it booted just fine. So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed." So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks. I mean why would I need to re-install operating system to add RAID setup?

    Read the article

  • Recovering damaged external hard disk by installing internally

    - by nfarshchi
    I had a 1TB Western Digital (My book series) 3.5" USB3. One day, the SATA to USB3 converter board was damaged and has not worked since. I decided to open the cover and use the HDD as an internal HDD. When I attached the HDD to my PC and booted up in Windows, it asked me which type of ????? I want to use "MBR or GBR" (I dont remember the exact question) I chose MBR and Windows gave me a 1TB empty Hard drive. I tried to recover with recover my files and some other recovery programs but no success. Some one told me that you should choosed GBR instead of MBR . How can I do that now? Another guy told me that the SATA to USB3 converter board is coded to save data on HDD and you can not use them internally without losing data, and I should find another SATA to USB3 board (exact same). It is impossible to find because they are not produced any more. Please help me to find a solution to bring back my data. UPDATE I have 1TB WD "Mybook" USB 3. the board that convert sata to usb3 was damaged. so when the HDD was in the box computer did not recognize it. I opened the box and remove HDD to use it internal. after connecting to my PC windows showed me one massage that I had two choice MBR or GPT I choosed MBR one and windows gave me 1TB empty new volume. I tried many recovery software to recover my data but no success. I brought it to one expert recovery company and they told me the converter board (SATA to USB3) make some encryption on data and with out that board you cannot recover any thing. so I bought another empty WD box and put the HDD inside but even after that also there is no file. I tried to recover again in this state but no success. so I have some unanswered question. does this converted boards make any password or encryption? if yes how can I solve it? does using many recovery programs affected my data? any suggestion or solution for bring back my data? I had use recovery programs such as : recover my files , EaseUS data recovery, easy recovery, test disk, Ontrack easy recovery . Note: when I was using test disk it asked me to choose which partition table I want to use. as it was I choose NTFS, does this made any change on data?

    Read the article

  • Create text file named after a cell containing other cell data

    - by user143041
    I tried using the code below for the Excel program on my `Mac Mini using the OS X Version 10.7.2 and it keeps saying Error due to file name / path: (The Excel file I am creating is going to be a template with my formulas and macros installed which will be used over and over). Sub CreateFile() Do While Not IsEmpty(ActiveCell.Offset(0, 1)) MyFile = ActiveCell.Value & ".txt" fnum = FreeFile() Open MyFile For Output As fnum Print #fnum, ActiveCell.Offset(0, 1) & " " & ActiveCell.Offset(0, 2) Close #fnum ActiveCell.Offset(1, 0).Select Loop End Sub What Im trying to do: 1st Objective I would like to have the following data to be used to create a text file. A:A is what I need the name of the file to be. B:2 is the content I need in the text file. So, A2 - "repair-video-game-Glassboro-NJ-08028.txt" is the file name and B2 to be the content in the file. Next, A3 is the file name and B3 is the content for the file, etc. ONCE the content reads what is in cell A16 and B16 (length will vary), the file creation should stop, if not then I can delete the additional files created. This sheet will never change. Is there a way to establish the excel macro to always go to this sheet instead of have to select it with the mouse to identify the starting point? 2nd Objective I would like to have the following data to be used to create a text file. A:1 is what I need the name of the file to be. B:B is the content I want in the file. So, A2 - is the file name "geo-sitemap.xml" and B:B to be the content in the file (ignore the .xml file extension in the photo). ONCE the content cell reads what is in cell "B16" (length will vary), the file creation should stop, if not then I can adjust the cells that have need content (formulated content you see in the image is preset for 500 rows). This sheet will never change. Is there a way to establish the excel macro to always go to this sheet instead of have to select it with the mouse to identify the starting point? I can Provide the content in the cells that are filled in by excel formulas that are not not to be included in the .txt files. It is ok if it is not possible. I can delete the extra cells that are not populated (based on the data sheet). Please let me know if you need any more additional information or clarity and I will be happy to provide it.

    Read the article

  • A Windows Update Prevented Live Discs From Working?

    - by user88311
    First off I'll state my system specs. Acer Aspire M1100 Windows Vista Home Basic 32bit OEM 2 Gigs of DDR2 ram 160Gig hard drive 2.7Ghz AMD Athlon 64 processor ATI Radeon X1250 Graphics card A few days ago my computer did automatic updates and updated windows defender to KB915597 (Definition 1.135.415.0), After which when shutting down and starting up I would receive BSOD with the information BUGCODE_USE_DRIVER and 0x000000FE (0x00000008, 0x00000006, 0x00000006, 0x877330000) upon where my computer would not start up with any USB devices plugged in and it always require me to run startup repair before it started. Upon when I first started it up and was able to fully boot windows, I had no use of the mouse so I was unable to install the fix that the windows solutions center brought up on my screen, so I restarted again and installed the fix hoping it would cease the problem, it did not. Upoon starting up after installing the fix and restarting I was confronted with the BSOD 0x000000FE (0x00000008, 0x00000006, 0x00000006, 0x83291000) at which I found the startup repair could not fix the problem and I restored, as I most like should have in the first place. After going through that I read that simply installing the latest defender version from the microsoft site had fixed this problem for others, so I did that, to find I still received the BSOD's. So in a attempt to find a fix to the problem I went to the microsoft answers site to try to find a way to fix the problem, there I was told to simply disable defender and reboot to see if that fixed the problem, upon doing this my computer would no longer even startup, when I boot normally I get to just when the loading screen finishes and then my computer restarts and when I run startup repair, it runs for about 15 seconds and then my computer restarts as well. I have tried running ubuntu live discs in order to simply access the drive and simply copy and paste the 2 month old physical backup I have of my C drive to the C drive, but whenever I run the live OS when it gets to the end of the load screen and is about to boot, the computer again restarts, yet if I put in a gparted disc, I am able to boot it fully, although it does not give me access to the file system just partition managing and when I attempt to access the internet through it, the computer once again restarts. So my question is, how could the update and what has happened prevent me from running the live OS's properly?

    Read the article

  • Windows 7 booting and startup repair issues

    - by aardvark
    I have a MSI FR720 laptop with Windows 7 and Lubuntu partions. For quite a while (6 months or so) I've been having issues booting from my hard drive, it'd take me between 5 minutes and several hours for me to be able to have it recognize the hard drive as a bootable device. I did several disk checks on it, and my hard drive seems in perfect condition, and the fact that booting would usually only work after removing the hard drive and trying to reset it in its slot or lightly shaking it makes me think it had something to do with the connection in the hard drive slot as opposed to the hard drive itself. I was having particular issues with it detecting the hard drive today so I decided to try booting it from an external hard drive dock. It detected it first try and so far has had no problems finding the bootable partitions on my hard drive. When I selected my Windows 7 partition from the boot menu it said that it hadn't been shut down properly last time and needed startup repair. I've done this several times over the last 6 months, so this is hardly unusual. I do startup repair, it fails, and then I try to do a system restore. The system restore also failed, and it says that no files were changed. I restart and try it again. However, this time when I get to the startup repair it's not detecting a Windows OS. I tried clicking next and doing a startup repair but the repair is always failing. If I ignore the startup repair option and instead select "Launch windows normally" it will get to the windows animation, stop halfway through and then crash into a BSoD. I can't read the error on the screen because it immediately switches to back and tries to restart. This is my first time asking a question like this online, so let me know if I need to provide any extra information and I'll do my best to give it I tried using diskpart to find the list of partitions and see if one's labelled as an active partition, but it says that no disk were detected. I can run Lubuntu just fine. I can also see all of my Windows 7 files from it EDIT: The startup repair diagnosis and repair log is this: -- Number of repair attempts: 1 Session details System Disk = Windows directory = AutoChk Run = 0 Number of root causes = 1 Test Performed: Name: Check for updates Result: Completed successfully. Error code = 0x0 Time taken = 15ms Test Performed: Name: System disk test Result: Completed successfully. Error code = 0x0 Time taken = 31ms Root cause found. If a hard disk is installed, it is not responding. -- Any chance that this is a result of me doing this through an external dock through a USB drive?

    Read the article

  • Lenovo Windows 8 EFI restore from image

    - by anderhil
    First time here. I have bought e530 with windows 8 and the first hour of work with it i have a problem. I have ssd with windows 7 which i want to use with my new e530. I have made a sysprep of win 7 and installed ssd to the e530. The HDD which was inside e530 i want to use as second hdd instead of my DVD Drive. I connected this HDD through usb-to-sata adapter to copy some files from ssd to the hdd. Unfortunately it didn't see the file system on the HDD (but first time i have booted to it and first boot into Windows 8) I've made some mistakes and i corrupt the filesystem on the hdd. I tried bunch of tricks to recover the GPT, but it didn't work. I have managed to recover the Lenovo_Recovery partition to my ssd using recovery tools. And now I'm stuck, with this new things to me - EFI, GPT, etc i don't how this stuff works, and i have been trying to understand this for hours - but nothing seems to work. I want to restore the Windows 8 to the hdd, so it is there alive. What i have done so far: Formated the HDD I took the PBRALL file from the Lenovo_Recovery " convert gpt create partition Primary size=1000 ID=DE94BBA4-06D1-4D40-A16A-BFD50179D6AC gpt attributes=0x8000000000000001 assign letter=W format quick LABEL=WINRE_DRV create partition efi size=260 assign letter=s format quick fs=fat32 LABEL=SYSTEM_DRV create par msr size=128 create partition primary noerr assign letter=t format quick LABEL=Windows8_OS shrink desired=12197 create partition Primary ID=DE94BBA4-06D1-4D40-A16A-BFD50179D6AC gpt attributes=0x8000000000000001 assign letter=q format quick LABEL=Lenovo_Recovery " it recreated the partitions copied contents of SDRIVE.zip to SYSTEM_DRV partition copied contents of WDRIVE.zip to WINRE_DRV partition Copied restored Lenovo_Recovery back to Lenovo_Recovery partition So now I have 3 system partitions: SYSTE_DRV BOOT boot.sdi EFI BOOT bootx64.efi LenovoBT.efi Lenovo ... Microsoft ... WINRE_DRV\Recovery\WindowsRE\winre.wim Lenovo_Recovery (whic contains install.wim and bunch of other things) So i put back the HDD inside the laptop and tried to boot - but nothing works. It just doesn't boot to anything - no errors - nothing at all. When I choose this HDD manually for boot - just black screen blinks and that's all - it returns back to the devices boot menu. SYSTEM_DRV is EFI partition, so I don't understand why it doesn't boot, it has files needed inside. Can anybody tell me what should be done to make it boot to recovery console or smth like that? How to restore the Windows 8 from the Lenovo_Recovery install.wim image? As I understand I have all the files where they should be, but why it doesn't work? How to troubleshoot such things? Also, if somebody has good link where EFI booting process is explained in details that would be great. Cause i still don't understand how it knows what partition to boot?

    Read the article

  • ERROR: Linux route add command failed: external program exited with error status: 4

    - by JohnMerlino
    A remote machine running fedora uses openvpn, and multiple developers were successfully able to connect to it via their client openvpn. However, I am running Ubuntu 12.04 and I am having trouble connecting to the server via vpn. I copied ca.crt, home.key, and home.crt from the server to my local machine to /etc/openvpn folder. My client.conf file looks like this: ############################################## # Sample client-side OpenVPN 2.0 config file # # for connecting to multi-client server. # # # # This configuration can be used by multiple # # clients, however each client should have # # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel # if you have more than one. On XP SP2, # you may need to disable the firewall # for the TAP adapter. ;dev-node MyTap # Are we connecting to a TCP or # UDP server? Use the same setting as # on the server. ;proto tcp proto udp # The hostname/IP and port of the server. # You can have multiple remote entries # to load balance between the servers. remote xx.xxx.xx.130 1194 ;remote my-server-2 1194 # Choose a random host from the remote # list for load-balancing. Otherwise # try hosts in the order specified. ;remote-random # Keep trying indefinitely to resolve the # host name of the OpenVPN server. Very useful # on machines which are not permanently connected # to the internet such as laptops. resolv-retry infinite # Most clients don't need to bind to # a specific local port number. nobind # Downgrade privileges after initialization (non-Windows only) ;user nobody ;group nogroup # Try to preserve some state across restarts. persist-key persist-tun # If you are connecting through an # HTTP proxy to reach the actual OpenVPN # server, put the proxy server/IP and # port number here. See the man page # if your proxy server requires # authentication. ;http-proxy-retry # retry on connection failures ;http-proxy [proxy server] [proxy port #] # Wireless networks often produce a lot # of duplicate packets. Set this flag # to silence duplicate packet warnings. ;mute-replay-warnings # SSL/TLS parms. # See the server config file for more # description. It's best to use # a separate .crt/.key file pair # for each client. A single ca # file can be used for all clients. ca ca.crt cert home.crt key home.key # Verify server certificate by checking # that the certicate has the nsCertType # field set to "server". This is an # important precaution to protect against # a potential attack discussed here: # http://openvpn.net/howto.html#mitm # # To use this feature, you will need to generate # your server certificates with the nsCertType # field set to "server". The build-key-server # script in the easy-rsa folder will do this. ns-cert-type server # If a tls-auth key is used on the server # then every client must also have the key. ;tls-auth ta.key 1 # Select a cryptographic cipher. # If the cipher option is used on the server # then you must also specify it here. ;cipher x # Enable compression on the VPN link. # Don't enable this unless it is also # enabled in the server config file. comp-lzo # Set log file verbosity. verb 3 # Silence repeating messages ;mute 20 But when I start server and look in /var/log/syslog, I notice the following error: May 27 22:13:51 myuser ovpn-client[5626]: /sbin/route add -net 10.27.12.1 netmask 255.255.255.252 gw 10.27.12.37 May 27 22:13:51 myuser ovpn-client[5626]: ERROR: Linux route add command failed: external program exited with error status: 4 May 27 22:13:51 myuser ovpn-client[5626]: /sbin/route add -net 172.27.12.0 netmask 255.255.255.0 gw 10.27.12.37 May 27 22:13:51 myuser ovpn-client[5626]: /sbin/route add -net 10.27.12.1 netmask 255.255.255.255 gw 10.27.12.37 And I am unable to connect to the server via openvpn: $ ssh [email protected] ssh: connect to host xxx.xx.xx.130 port 22: No route to host What may I be doing wrong?

    Read the article

  • TFS 2010 SDK: Connecting to TFS 2010 Programmatically&ndash;Part 1

    - by Tarun Arora
    Technorati Tags: Team Foundation Server 2010,TFS 2010 SDK,TFS API,TFS Programming,TFS ALM   Download Working Demo Great! You have reached that point where you would like to extend TFS 2010. The first step is to connect to TFS programmatically. 1. Download TFS 2010 SDK => http://visualstudiogallery.msdn.microsoft.com/25622469-19d8-4959-8e5c-4025d1c9183d?SRC=VSIDE 2. Alternatively you can also download this from the visual studio extension manager 3. Create a new Windows Forms Application project and add reference to TFS Common and client dlls Note - If Microsoft.TeamFoundation.Client and Microsoft.TeamFoundation.Common do not appear on the .NET tab of the References dialog box, use the Browse tab to add the assemblies. You can find them at %ProgramFiles%\Microsoft Visual Studio 10.0\Common7\IDE\ReferenceAssemblies\v2.0. using Microsoft.TeamFoundation.Client; using Microsoft.TeamFoundation.Framework.Client; using Microsoft.TeamFoundation.Framework.Common;   4. There are several ways to connect to TFS, the two classes of interest are, Option 1 – Class – TfsTeamProjectCollectionClass namespace Microsoft.TeamFoundation.Client { public class TfsTeamProjectCollection : TfsConnection { public TfsTeamProjectCollection(RegisteredProjectCollection projectCollection); public TfsTeamProjectCollection(Uri uri); public TfsTeamProjectCollection(RegisteredProjectCollection projectCollection, IdentityDescriptor identityToImpersonate); public TfsTeamProjectCollection(Uri uri, ICredentials credentials); public TfsTeamProjectCollection(Uri uri, ICredentialsProvider credentialsProvider); public TfsTeamProjectCollection(Uri uri, IdentityDescriptor identityToImpersonate); public TfsTeamProjectCollection(RegisteredProjectCollection projectCollection, ICredentials credentials, ICredentialsProvider credentialsProvider); public TfsTeamProjectCollection(Uri uri, ICredentials credentials, ICredentialsProvider credentialsProvider); public TfsTeamProjectCollection(RegisteredProjectCollection projectCollection, ICredentials credentials, ICredentialsProvider credentialsProvider, IdentityDescriptor identityToImpersonate); public TfsTeamProjectCollection(Uri uri, ICredentials credentials, ICredentialsProvider credentialsProvider, IdentityDescriptor identityToImpersonate); public override CatalogNode CatalogNode { get; } public TfsConfigurationServer ConfigurationServer { get; internal set; } public override string Name { get; } public static Uri GetFullyQualifiedUriForName(string name); protected override object GetServiceInstance(Type serviceType, object serviceInstance); protected override object InitializeTeamFoundationObject(string fullName, object instance); } } Option 2 – Class – TfsConfigurationServer namespace Microsoft.TeamFoundation.Client { public class TfsConfigurationServer : TfsConnection { public TfsConfigurationServer(RegisteredConfigurationServer application); public TfsConfigurationServer(Uri uri); public TfsConfigurationServer(RegisteredConfigurationServer application, IdentityDescriptor identityToImpersonate); public TfsConfigurationServer(Uri uri, ICredentials credentials); public TfsConfigurationServer(Uri uri, ICredentialsProvider credentialsProvider); public TfsConfigurationServer(Uri uri, IdentityDescriptor identityToImpersonate); public TfsConfigurationServer(RegisteredConfigurationServer application, ICredentials credentials, ICredentialsProvider credentialsProvider); public TfsConfigurationServer(Uri uri, ICredentials credentials, ICredentialsProvider credentialsProvider); public TfsConfigurationServer(RegisteredConfigurationServer application, ICredentials credentials, ICredentialsProvider credentialsProvider, IdentityDescriptor identityToImpersonate); public TfsConfigurationServer(Uri uri, ICredentials credentials, ICredentialsProvider credentialsProvider, IdentityDescriptor identityToImpersonate); public override CatalogNode CatalogNode { get; } public override string Name { get; } protected override object GetServiceInstance(Type serviceType, object serviceInstance); public TfsTeamProjectCollection GetTeamProjectCollection(Guid collectionId); protected override object InitializeTeamFoundationObject(string fullName, object instance); } }   Note – The TeamFoundationServer class is obsolete. Use the TfsTeamProjectCollection or TfsConfigurationServer classes to talk to a 2010 Team Foundation Server. In order to talk to a 2005 or 2008 Team Foundation Server use the TfsTeamProjectCollection class. 5. Sample code for programmatically connecting to TFS 2010 using the TFS 2010 API How do i know what the URI of my TFS server is, Note – You need to be have Team Project Collection view details permission in order to connect, expect to receive an authorization failure message if you do not have sufficient permissions. Case 1: Connect by Uri string _myUri = @"https://tfs.codeplex.com:443/tfs/tfs30"; TfsConfigurationServer configurationServer = TfsConfigurationServerFactory.GetConfigurationServer(new Uri(_myUri)); Case 2: Connect by Uri, prompt for credentials string _myUri = @"https://tfs.codeplex.com:443/tfs/tfs30"; TfsConfigurationServer configurationServer = TfsConfigurationServerFactory.GetConfigurationServer(new Uri(_myUri), new UICredentialsProvider()); configurationServer.EnsureAuthenticated(); Case 3: Connect by Uri, custom credentials In order to use this method of connectivity you need to implement the interface ICredentailsProvider public class ConnectByImplementingCredentialsProvider : ICredentialsProvider { public ICredentials GetCredentials(Uri uri, ICredentials iCredentials) { return new NetworkCredential("UserName", "Password", "Domain"); } public void NotifyCredentialsAuthenticated(Uri uri) { throw new ApplicationException("Unable to authenticate"); } } And now consume the implementation of the interface, string _myUri = @"https://tfs.codeplex.com:443/tfs/tfs30"; ConnectByImplementingCredentialsProvider connect = new ConnectByImplementingCredentialsProvider(); ICredentials iCred = new NetworkCredential("UserName", "Password", "Domain"); connect.GetCredentials(new Uri(_myUri), iCred); TfsConfigurationServer configurationServer = TfsConfigurationServerFactory.GetConfigurationServer(new Uri(_myUri), connect); configurationServer.EnsureAuthenticated();   6. Programmatically query TFS 2010 using the TFS SDK for all Team Project Collections and retrieve all Team Projects and output the display name and description of each team project. CatalogNode catalogNode = configurationServer.CatalogNode; ReadOnlyCollection<CatalogNode> tpcNodes = catalogNode.QueryChildren( new Guid[] { CatalogResourceTypes.ProjectCollection }, false, CatalogQueryOptions.None); // tpc = Team Project Collection foreach (CatalogNode tpcNode in tpcNodes) { Guid tpcId = new Guid(tpcNode.Resource.Properties["InstanceId"]); TfsTeamProjectCollection tpc = configurationServer.GetTeamProjectCollection(tpcId); // Get catalog of tp = 'Team Projects' for the tpc = 'Team Project Collection' var tpNodes = tpcNode.QueryChildren( new Guid[] { CatalogResourceTypes.TeamProject }, false, CatalogQueryOptions.None); foreach (var p in tpNodes) { Debug.Write(Environment.NewLine + " Team Project : " + p.Resource.DisplayName + " - " + p.Resource.Description + Environment.NewLine); } }   Output   You can download a working demo that uses TFS SDK 2010 to programmatically connect to TFS 2010. Screen Shots of the attached demo application, Share this post :

    Read the article

  • Map a Network Drive from XP to Windows 7

    - by Mysticgeek
    We’ve received a lot of questions about mapping a drive from XP to Windows 7 to access data easily. Today we look at how to map a drive in Windows 7, and how to map to an XP drive from Windows 7. With the new Homegroup feature in Windows 7, it makes sharing data between computers a lot easier. But you might need to map a network drive so you can go directly into a folder to access its contents. Mapping a network drive may sound like “IT talk”, but the process is fairly easy. Map Network Drive in Windows 7 Note: All of the computers used in this article are part of the same workgroup on a home network. In this first example we’re mapping to another Windows 7 drive on the network. Open Computer and from the toolbar click on Map Network Drive. Alternately in Computer you can hit “Alt+T” to pull up the toolbar and click on Tools \ Map Network Drive. Now give it an available drive letter, type in the path or browse to the folder you want to map to. Check the box next to Reconnect at logon if you want it available after a reboot, and click Finish. If both machines aren’t part of the same Homegroup, you may be prompted to enter in a username and password. Make sure and check the box next to Remember my credentials if you don’t want to log in every time to access it. The drive will map and the contents of the folder will open up. When you look in Computer, you’ll see the drive under network location. This process works if you want to connect to a server drive as well. In this example we map to a Home Server drive. Map an XP Drive to Windows 7 There might be times when you need to map a drive on an XP machine on your network. There are extra steps you’ll need to take to make it work however. Here we take a look at the problem you’ll encounter when trying to map to an XP machine if things aren’t set up correctly. If you try to browse to your XP machine you’ll see a message that you don’t have permission. Or if you try to enter in the path directly, you’ll be prompted for a username and password, and the annoyance is, no matter what credentials you put in, you can’t connect. To solve the problem we need to set up the Windows 7 machine as a user on the XP machine and make them part of the Administrators group. Right-click My Computer and select Manage. Under Computer Management expand Local Users and Groups and click on the Users folder. Right-click an empty area and click New User. Add in the user credentials, uncheck User must change password at next logon, then check Password never expires then click Create. Now you see the new user you created in the list. After the user is added you might want to reboot before proceeding to the next step.   Next we need to make the user part of the Administrators group. So go back into Computer Management \ Local Users and Groups \ Groups then double click on Administrators. Click the Add button in Administrators Properties window. Enter in the new user you created and click OK. An easy way to do this is to enter the name of the user you created then click Check Names and the path will be entered in for you. Now you see the user as a member of the Administrators group. Back on the Windows 7 machine we’ll start the process of mapping a drive. Here we’re browsing to the XP Media Center Edition machine. Now we can enter in the user name and password we just created. If you only want to access specific shared folders on the XP machine you can browse to them. Or if you want to map to the entire drive, enter in the drive path where in this example it’s “\\XPMCE\C$” –Don’t forget the “$” sign after the local drive letter. Then login… Again the contents of the drive will open up for you to access. Here you can see we have two drives mapped. One to another Windows 7 machine on the network, and the other one to the XP computer.   If you ever want to disconnect a drive, just right-click on it and then Disconnect. There are several scenarios where you might want to map a drive in Windows 7 to access specific data. It takes a little bit of work but you can map to an XP drive from Windows 7 as well. This comes in handy where you have a network with different versions of Windows running on it. Similar Articles Productive Geek Tips Find Your Missing USB Drive on Windows XPMake Vista Index Your Network ConnectionsEasily Backup & Import Your Wireless Network Settings in Windows 7Quickly Open Network Connections List in Windows 7 or VistaHow To Find Drives Easily with Desk Drive TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Kill Processes Quickly with Process Assassin Need to Come Up with a Good Name? Try Wordoid StockFox puts a Lightweight Stock Ticker in your Statusbar Explore Google Public Data Visually The Ultimate Excel Cheatsheet Convert the Quick Launch Bar into a Super Application Launcher

    Read the article

  • A class meant for an alfresco behavior and its bean, how do they work and how are they deployed trough eclipse

    - by MrHappy
    (This is a partial repost of a question asked 10 days ago because only 1 part was answered(not included), I've rewritten it into a way better question and added 3 more tags) where do I put the DeleteAsset.class or why isn't it being found? I've put the compiled class from the bin of the workspace of eclipse into alfresco-4.2.c/tomcat/webapps/alfresco/WEB-INF/classes/com/openerp/behavior/ and right now it's giving me Error loading class [com.openerp.behavior.DeleteAsset] for bean with name 'deletionBehavior' defined in URL [file:/home/openerp/alfresco-4.2.c/tomcat/shared/classes/alfresco/extension/cust??om-web-context.xml]: problem with class file or dependent class; nested exception is java.lang.NoClassDefFoundError: com/openerp/behavior/DeleteAsset (wrong name: DeleteAsset) when I put it in there. (See bean below!) The code(I'd trying to work without the model class, idk if I made any silly mistakes on that): package com.openerp.behavior; import java.util.List; import java.net.*; import java.io.*; import org.alfresco.repo.node.NodeServicePolicies; import org.alfresco.repo.policy.Behaviour; import org.alfresco.repo.policy.JavaBehaviour; import org.alfresco.repo.policy.PolicyComponent; import org.alfresco.repo.policy.Behaviour.NotificationFrequency; import org.alfresco.repo.security.authentication.AuthenticationUtil; import org.alfresco.repo.security.authentication.AuthenticationUtil.RunAsWork; import org.alfresco.service.cmr.repository.ChildAssociationRef; import org.alfresco.service.cmr.repository.NodeRef; import org.alfresco.service.cmr.repository.NodeService; import org.alfresco.service.namespace.NamespaceService; import org.alfresco.service.namespace.QName; import org.alfresco.service.transaction.TransactionService; import org.apache.log4j.Logger; //this is the newer version //import com.openerp.model.openerpJavaModel; public class DeleteAsset implements NodeServicePolicies.BeforeDeleteNodePolicy { private PolicyComponent policyComponent; private Behaviour beforeDeleteNode; private NodeService nodeService; public void init() { this.beforeDeleteNode = new JavaBehaviour(this,"beforeDeleteNode",NotificationFrequency.EVERY_EVENT); this.policyComponent.bindClassBehaviour(QName.createQName("http://www.someco.com/model/content/1.0","beforeDeleteNode"), QName.createQName("http://www.someco.com/model/content/1.0","sc:doc"), this.beforeDeleteNode); } public setNodeService(NodeService nodeService){ this.nodeService = nodeService; } @Override public void beforeDeleteNode(NodeRef node) { System.out.println("beforeDeleteNode!"); try { QName attachmentID1= QName.createQName("http://www.someco.com/model/content/1.0", "OpenERPattachmentID1"); // this could/shoul be defined in your OpenERPModel-class int attachmentid = (Integer)nodeService.getProperty(node, attachmentID1); //int attachmentid = 123; URL oracle = new URL("http://0.0.0.0:1885/delete/%20?attachmentid=" + attachmentid); URLConnection yc = oracle.openConnection(); BufferedReader in = new BufferedReader(new InputStreamReader( yc.getInputStream())); String inputLine; while ((inputLine = in.readLine()) != null) //System.out.println(inputLine); in.close(); } catch(Exception e) { e.printStackTrace(); } } } This is my full custom-web-context file: <?xml version='1.0' encoding='UTF-8'?> <!DOCTYPE beans PUBLIC '-//SPRING//DTD BEAN//EN' 'http://www.springframework.org/dtd/spring-beans.dtd'> <beans> <!-- Registration of new models --> <bean id="smartsolution.dictionaryBootstrap" parent="dictionaryModelBootstrap" depends-on="dictionaryBootstrap"> <property name="models"> <list> <value>alfresco/extension/scOpenERPModel.xml</value> </list> </property> </bean> <!-- deletion of attachments within openERP when delete is initiated in Alfresco--> <bean id="DeleteAsset" class="com.openerp.behavior.DeleteAsset" init-method="init"> <property name="NodeService"> <ref bean="NodeService" /> </property> <property name="PolicyComponent"> <ref bean="PolicyComponent" /> </property> </bean> and content type: <type name="sc:doc"> <title>OpenERP Document</title> <parent>cm:content</parent> There's also this when I open share An error has occured in the Share component: /share/service/components/dashlets/my-sites. It responded with a status of 500 - Internal Error. Error Code Information: 500 - An error inside the HTTP server which prevented it from fulfilling the request. Error Message: 09230001 Failed to execute script 'classpath*:alfresco/site-webscripts/org/alfresco/components/dashlets/my-sites.get.js': 09230000 09230001 Failed during processing of IMAP server status configuration from Alfresco: 09230000 Unable to retrieve IMAP server status from Alfresco: 404 Server: Alfresco Spring WebScripts - v1.2.0 (Release 1207) schema 1,000 Time: Oct 23, 2013 11:40:06 AM Click here to view full technical information on the error. Exception: org.alfresco.error.AlfrescoRuntimeException - 09230001 Failed during processing of IMAP server status configuration from Alfresco: 09230000 Unable to retrieve IMAP server status from Alfresco: 404 org.alfresco.web.scripts.SingletonValueProcessorExtension.getSingletonValue(SingletonValueProcessorExtension.java:108) org.alfresco.web.scripts.SingletonValueProcessorExtension.getSingletonValue(SingletonValueProcessorExtension.java:59) org.alfresco.web.scripts.ImapServerStatus.getEnabled(ImapServerStatus.java:49) sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) java.lang.reflect.Method.invoke(Method.java:606) org.mozilla.javascript.MemberBox.invoke(MemberBox.java:155) org.mozilla.javascript.JavaMembers.get(JavaMembers.java:117) org.mozilla.javascript.NativeJavaObject.get(NativeJavaObject.java:113) org.mozilla.javascript.ScriptableObject.getProperty(ScriptableObject.java:1544) org.mozilla.javascript.ScriptRuntime.getObjectProp(ScriptRuntime.java:1375) org.mozilla.javascript.ScriptRuntime.getObjectProp(ScriptRuntime.java:1364) org.mozilla.javascript.gen.c6._c1(file:/opt/alfresco-4.2.c/tomcat/webapps/share/WEB-INF/classes/alfresco/site-webscripts/org/alfresco/components/dashlets/my-sites.get.js:4) org.mozilla.javascript.gen.c6.call(file:/opt/alfresco-4.2.c/tomcat/webapps/share/WEB-INF/classes/alfresco/site-webscripts/org/alfresco/components/dashlets/my-sites.get.js) org.mozilla.javascript.optimizer.OptRuntime.callName0(OptRuntime.java:108) org.mozilla.javascript.gen.c6._c0(file:/opt/alfresco-4.2.c/tomcat/webapps/share/WEB-INF/classes/alfresco/site-webscripts/org/alfresco/components/dashlets/my-sites.get.js:51) org.mozilla.javascript.gen.c6.call(file:/opt/alfresco-4.2.c/tomcat/webapps/share/WEB-INF/classes/alfresco/site-webscripts/org/alfresco/components/dashlets/my-sites.get.js) org.mozilla.javascript.ContextFactory.doTopCall(ContextFactory.java:393) org.mozilla.javascript.ScriptRuntime.doTopCall(ScriptRuntime.java:2834) org.mozilla.javascript.gen.c6.call(file:/opt/alfresco-4.2.c/tomcat/webapps/share/WEB-INF/classes/alfresco/site-webscripts/org/alfresco/components/dashlets/my-sites.get.js) org.mozilla.javascript.gen.c6.exec(file:/opt/alfresco-4.2.c/tomcat/webapps/share/WEB-INF/classes/alfresco/site-webscripts/org/alfresco/components/dashlets/my-sites.get.js) org.springframework.extensions.webscripts.processor.JSScriptProcessor.executeScriptImpl(JSScriptProcessor.java:318) org.springframework.extensions.webscripts.processor.JSScriptProcessor.executeScript(JSScriptProcessor.java:192) org.springframework.extensions.webscripts.AbstractWebScript.executeScript(AbstractWebScript.java:1305) org.springframework.extensions.webscripts.DeclarativeWebScript.execute(DeclarativeWebScript.java:86) org.springframework.extensions.webscripts.PresentationContainer.executeScript(PresentationContainer.java:70) org.springframework.extensions.webscripts.LocalWebScriptRuntimeContainer.executeScript(LocalWebScriptRuntimeContainer.java:240) org.springframework.extensions.webscripts.AbstractRuntime.executeScript(AbstractRuntime.java:377) org.springframework.extensions.webscripts.AbstractRuntime.executeScript(AbstractRuntime.java:209) org.springframework.extensions.webscripts.WebScriptProcessor.executeBody(WebScriptProcessor.java:310) org.springframework.extensions.surf.render.AbstractProcessor.execute(AbstractProcessor.java:57) org.springframework.extensions.surf.render.RenderService.process(RenderService.java:599) org.springframework.extensions.surf.render.RenderService.renderSubComponent(RenderService.java:505) org.springframework.extensions.surf.render.RenderService.renderChromeInclude(RenderService.java:1284) org.springframework.extensions.directives.ChromeIncludeFreeMarkerDirective.execute(ChromeIncludeFreeMarkerDirective.java:81) freemarker.core.Environment.visit(Environment.java:274) freemarker.core.UnifiedCall.accept(UnifiedCall.java:126) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.MixedContent.accept(MixedContent.java:92) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.IfBlock.accept(IfBlock.java:82) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.MixedContent.accept(MixedContent.java:92) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.Environment.process(Environment.java:199) org.springframework.extensions.webscripts.processor.FTLTemplateProcessor.process(FTLTemplateProcessor.java:171) org.springframework.extensions.webscripts.WebTemplateProcessor.executeBody(WebTemplateProcessor.java:438) org.springframework.extensions.surf.render.AbstractProcessor.execute(AbstractProcessor.java:57) org.springframework.extensions.surf.render.RenderService.processRenderable(RenderService.java:204) org.springframework.extensions.surf.render.bean.ChromeRenderer.body(ChromeRenderer.java:95) org.springframework.extensions.surf.render.AbstractRenderer.render(AbstractRenderer.java:77) org.springframework.extensions.surf.render.bean.ChromeRenderer.render(ChromeRenderer.java:86) org.springframework.extensions.surf.render.RenderService.processComponent(RenderService.java:432) org.springframework.extensions.surf.render.bean.ComponentRenderer.body(ComponentRenderer.java:94) org.springframework.extensions.surf.render.AbstractRenderer.render(AbstractRenderer.java:77) org.springframework.extensions.surf.render.RenderService.renderComponent(RenderService.java:961) org.springframework.extensions.surf.render.RenderService.renderRegionComponents(RenderService.java:900) org.springframework.extensions.surf.render.RenderService.renderChromeInclude(RenderService.java:1263) org.springframework.extensions.directives.ChromeIncludeFreeMarkerDirective.execute(ChromeIncludeFreeMarkerDirective.java:81) freemarker.core.Environment.visit(Environment.java:274) freemarker.core.UnifiedCall.accept(UnifiedCall.java:126) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.MixedContent.accept(MixedContent.java:92) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.Environment.process(Environment.java:199) org.springframework.extensions.webscripts.processor.FTLTemplateProcessor.process(FTLTemplateProcessor.java:171) org.springframework.extensions.webscripts.WebTemplateProcessor.executeBody(WebTemplateProcessor.java:438) org.springframework.extensions.surf.render.AbstractProcessor.execute(AbstractProcessor.java:57) org.springframework.extensions.surf.render.RenderService.processRenderable(RenderService.java:204) org.springframework.extensions.surf.render.bean.ChromeRenderer.body(ChromeRenderer.java:95) org.springframework.extensions.surf.render.AbstractRenderer.render(AbstractRenderer.java:77) org.springframework.extensions.surf.render.bean.ChromeRenderer.render(ChromeRenderer.java:86) org.springframework.extensions.surf.render.bean.RegionRenderer.body(RegionRenderer.java:99) org.springframework.extensions.surf.render.AbstractRenderer.render(AbstractRenderer.java:77) org.springframework.extensions.surf.render.RenderService.renderRegion(RenderService.java:851) org.springframework.extensions.directives.RegionDirectiveData.render(RegionDirectiveData.java:91) org.springframework.extensions.surf.extensibility.impl.ExtensibilityModelImpl.merge(ExtensibilityModelImpl.java:408) org.springframework.extensions.surf.extensibility.impl.AbstractExtensibilityDirective.merge(AbstractExtensibilityDirective.java:169) org.springframework.extensions.surf.extensibility.impl.AbstractExtensibilityDirective.execute(AbstractExtensibilityDirective.java:137) freemarker.core.Environment.visit(Environment.java:274) freemarker.core.UnifiedCall.accept(UnifiedCall.java:126) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.IteratorBlock$Context.runLoop(IteratorBlock.java:179) freemarker.core.Environment.visit(Environment.java:428) freemarker.core.IteratorBlock.accept(IteratorBlock.java:102) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.MixedContent.accept(MixedContent.java:92) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.IteratorBlock$Context.runLoop(IteratorBlock.java:179) freemarker.core.Environment.visit(Environment.java:428) freemarker.core.IteratorBlock.accept(IteratorBlock.java:102) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.MixedContent.accept(MixedContent.java:92) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.Macro$Context.runMacro(Macro.java:172) freemarker.core.Environment.visit(Environment.java:614) freemarker.core.UnifiedCall.accept(UnifiedCall.java:106) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.IfBlock.accept(IfBlock.java:82) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.Macro$Context.runMacro(Macro.java:172) freemarker.core.Environment.visit(Environment.java:614) freemarker.core.UnifiedCall.accept(UnifiedCall.java:106) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.MixedContent.accept(MixedContent.java:92) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.Environment$3.render(Environment.java:246) org.springframework.extensions.surf.extensibility.impl.DefaultExtensibilityDirectiveData.render(DefaultExtensibilityDirectiveData.java:119) org.springframework.extensions.surf.extensibility.impl.ExtensibilityModelImpl.merge(ExtensibilityModelImpl.java:408) org.springframework.extensions.surf.extensibility.impl.AbstractExtensibilityDirective.merge(AbstractExtensibilityDirective.java:169) org.springframework.extensions.surf.extensibility.impl.AbstractExtensibilityDirective.execute(AbstractExtensibilityDirective.java:137) freemarker.core.Environment.visit(Environment.java:274) freemarker.core.UnifiedCall.accept(UnifiedCall.java:126) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.MixedContent.accept(MixedContent.java:92) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.Environment.visit(Environment.java:406) freemarker.core.BodyInstruction.accept(BodyInstruction.java:93) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.MixedContent.accept(MixedContent.java:92) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.Macro$Context.runMacro(Macro.java:172) freemarker.core.Environment.visit(Environment.java:614) freemarker.core.UnifiedCall.accept(UnifiedCall.java:106) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.MixedContent.accept(MixedContent.java:92) freemarker.core.Environment.visit(Environment.java:221) freemarker.core.Environment.process(Environment.java:199) org.springframework.extensions.webscripts.processor.FTLTemplateProcessor.process(FTLTemplateProcessor.java:171) org.springframework.extensions.webscripts.WebTemplateProcessor.executeBody(WebTemplateProcessor.java:438) org.springframework.extensions.surf.render.AbstractProcessor.execute(AbstractProcessor.java:57) org.springframework.extensions.surf.render.RenderService.processTemplate(RenderService.java:721) org.springframework.extensions.surf.render.bean.TemplateInstanceRenderer.body(TemplateInstanceRenderer.java:140) org.springframework.extensions.surf.render.AbstractRenderer.render(AbstractRenderer.java:77) org.springframework.extensions.surf.render.bean.PageRenderer.body(PageRenderer.java:85) org.springframework.extensions.surf.render.AbstractRenderer.render(AbstractRenderer.java:77) org.springframework.extensions.surf.render.RenderService.renderPage(RenderService.java:762) org.springframework.extensions.surf.mvc.PageView.dispatchPage(PageView.java:411) org.springframework.extensions.surf.mvc.PageView.renderView(PageView.java:306) org.springframework.extensions.surf.mvc.AbstractWebFrameworkView.renderMergedOutputModel(AbstractWebFrameworkView.java:316) org.springframework.web.servlet.view.AbstractView.render(AbstractView.java:250) org.springframework.web.servlet.DispatcherServlet.render(DispatcherServlet.java:1047) org.springframework.web.servlet.DispatcherServlet.doDispatch(DispatcherServlet.java:817) org.springframework.web.servlet.DispatcherServlet.doService(DispatcherServlet.java:719) org.springframework.web.servlet.FrameworkServlet.processRequest(FrameworkServlet.java:644) org.springframework.web.servlet.FrameworkServlet.doGet(FrameworkServlet.java:549) javax.servlet.http.HttpServlet.service(HttpServlet.java:621) javax.servlet.http.HttpServlet.service(HttpServlet.java:722) org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:305) org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:210) org.alfresco.web.site.servlet.MTAuthenticationFilter.doFilter(MTAuthenticationFilter.java:74) org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:243) org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:210) org.alfresco.web.site.servlet.SSOAuthenticationFilter.doFilter(SSOAuthenticationFilter.java:374) org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:243) org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:210) org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:222) org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:123) org.apache.catalina.authenticator.AuthenticatorBase.invoke(AuthenticatorBase.java:472) org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:168) org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:99) org.apache.catalina.valves.AccessLogValve.invoke(AccessLogValve.java:929) org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:118) org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:407) org.apache.coyote.http11.AbstractHttp11Processor.process(AbstractHttp11Processor.java:1002) org.apache.coyote.AbstractProtocol$AbstractConnectionHandler.process(AbstractProtocol.java:585) org.apache.tomcat.util.net.AprEndpoint$SocketWithOptionsProcessor.run(AprEndpoint.java:1771) java.util.concurrent.ThreadPoolExecutor.runWorker(ThreadPoolExecutor.java:1145) java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:615) java.lang.Thread.run(Thread.java:724) Exception: org.springframework.extensions.webscripts.WebScriptException - 09230000 09230001 Failed during processing of IMAP server status configuration from Alfresco: 09230000 Unable to retrieve IMAP server status from Alfresco: 404 org.springframework.extensions.webscripts.processor.JSScriptProcessor.executeScriptImpl(JSScriptProcessor.java:324) Exception: org.springframework.extensions.webscripts.WebScriptException - 09230001 Failed to execute script 'classpath*:alfresco/site-webscripts/org/alfresco/components/dashlets/my-sites.get.js': 09230000 09230001 Failed during processing of IMAP server status configuration from Alfresco: 09230000 Unable to retrieve IMAP server status from Alfresco: 404 org.springframework.extensions.webscripts.processor.JSScriptProcessor.executeScript(JSScriptProcessor.java:200) UPDATE: I think I've found the problem. Being a newbie to eclipse I haven't managed the dependecies well I think. Could anyone link me to a tutorial describing how to get org.alfresco.repo.node.NodeServicePolicies; as seen in import org.alfresco.repo.node.NodeServicePolicies; and other such imports into eclipse, I've got the alfresco source from svn but the tutorial I've found seems to fail me. java/lang/Error\00\F1Unresolved compilation problems: The declared package "com.openerp.behavior" does not match the expected package "java.com.openerp.behavior" The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.alfresco cannot be resolved The import org.apache cannot be resolved The import com.openerp cannot be resolved NodeServicePolicies cannot be resolved to a type PolicyComponent cannot be resolved to a type Behaviour cannot be resolved to a type NodeService cannot be resolved to a type Behaviour cannot be resolved to a type JavaBehaviour cannot be resolved to a type NotificationFrequency cannot be resolved to a variable PolicyComponent cannot be resolved to a type QName cannot be resolved QName cannot be resolved Behaviour cannot be resolved to a type Return type for the method is missing NodeService cannot be resolved to a type NodeService cannot be resolved to a type NodeRef cannot be resolved to a type QName cannot be resolved to a type QName cannot be resolved NodeService cannot be resolved to a type \00\00\00\00\00(Ljava/lang/String;)V\00LineNumberTable\00LocalVariableTable\00this\00'Ljava/com/openerp/behavior/DeleteAsset;\00init\008Unresolved compilation problems: Behaviour cannot be resolved to a type JavaBehaviour cannot be resolved to a type NotificationFrequency cannot be resolved to a variable PolicyComponent cannot be resolved to a type QName cannot be resolved QName cannot be resolved Behaviour cannot be resolved to a type \00(LNodeRef;)V\00\00\B0Unresolved compilation problems: NodeRef cannot be resolved to a type QName cannot be resolved to a type QName cannot be resolved NodeService cannot be resolved to a type

    Read the article

  • C# 5 Async, Part 1: Simplifying Asynchrony – That for which we await

    - by Reed
    Today’s announcement at PDC of the future directions C# is taking excite me greatly.  The new Visual Studio Async CTP is amazing.  Asynchronous code – code which frustrates and demoralizes even the most advanced of developers, is taking a huge leap forward in terms of usability.  This is handled by building on the Task functionality in .NET 4, as well as the addition of two new keywords being added to the C# language: async and await. This core of the new asynchronous functionality is built upon three key features.  First is the Task functionality in .NET 4, and based on Task and Task<TResult>.  While Task was intended to be the primary means of asynchronous programming with .NET 4, the .NET Framework was still based mainly on the Asynchronous Pattern and the Event-based Asynchronous Pattern. The .NET Framework added functionality and guidance for wrapping existing APIs into a Task based API, but the framework itself didn’t really adopt Task or Task<TResult> in any meaningful way.  The CTP shows that, going forward, this is changing. One of the three key new features coming in C# is actually a .NET Framework feature.  Nearly every asynchronous API in the .NET Framework has been wrapped into a new, Task-based method calls.  In the CTP, this is done via as external assembly (AsyncCtpLibrary.dll) which uses Extension Methods to wrap the existing APIs.  However, going forward, this will be handled directly within the Framework.  This will have a unifying effect throughout the .NET Framework.  This is the first building block of the new features for asynchronous programming: Going forward, all asynchronous operations will work via a method that returns Task or Task<TResult> The second key feature is the new async contextual keyword being added to the language.  The async keyword is used to declare an asynchronous function, which is a method that either returns void, a Task, or a Task<T>. Inside the asynchronous function, there must be at least one await expression.  This is a new C# keyword (await) that is used to automatically take a series of statements and break it up to potentially use discontinuous evaluation.  This is done by using await on any expression that evaluates to a Task or Task<T>. For example, suppose we want to download a webpage as a string.  There is a new method added to WebClient: Task<string> WebClient.DownloadStringTaskAsync(Uri).  Since this returns a Task<string> we can use it within an asynchronous function.  Suppose, for example, that we wanted to do something similar to my asynchronous Task example – download a web page asynchronously and check to see if it supports XHTML 1.0, then report this into a TextBox.  This could be done like so: private async void button1_Click(object sender, RoutedEventArgs e) { string url = "http://reedcopsey.com"; string content = await new WebClient().DownloadStringTaskAsync(url); this.textBox1.Text = string.Format("Page {0} supports XHTML 1.0: {1}", url, content.Contains("XHTML 1.0")); } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Let’s walk through what’s happening here, step by step.  By adding the async contextual keyword to the method definition, we are able to use the await keyword on our WebClient.DownloadStringTaskAsync method call. When the user clicks this button, the new method (Task<string> WebClient.DownloadStringTaskAsync(string)) is called, which returns a Task<string>.  By adding the await keyword, the runtime will call this method that returns Task<string>, and execution will return to the caller at this point.  This means that our UI is not blocked while the webpage is downloaded.  Instead, the UI thread will “await” at this point, and let the WebClient do it’s thing asynchronously. When the WebClient finishes downloading the string, the user interface’s synchronization context will automatically be used to “pick up” where it left off, and the Task<string> returned from DownloadStringTaskAsync is automatically unwrapped and set into the content variable.  At this point, we can use that and set our text box content. There are a couple of key points here: Asynchronous functions are declared with the async keyword, and contain one or more await expressions In addition to the obvious benefits of shorter, simpler code – there are some subtle but tremendous benefits in this approach.  When the execution of this asynchronous function continues after the first await statement, the initial synchronization context is used to continue the execution of this function.  That means that we don’t have to explicitly marshal the call that sets textbox1.Text back to the UI thread – it’s handled automatically by the language and framework!  Exception handling around asynchronous method calls also just works. I’d recommend every C# developer take a look at the documentation on the new Asynchronous Programming for C# and Visual Basic page, download the Visual Studio Async CTP, and try it out.

    Read the article

  • Ask How-To Geek: Dropbox in the Start Menu, Understanding Symlinks, and Ripping TV Series DVDs

    - by Jason Fitzpatrick
    This week we take a look at how to incorporate Dropbox into your Windows Start Menu, understanding and using symbolic links, and how to rip your TV series DVDs right to unique and high-quality episode files. Once a week we dip into our reader mailbag and help readers solve their problems, sharing the useful solutions with you in the process. Read on to see our fixes for this week’s reader dilemmas. Add Drobox to Your Start Menu Dear How-To Geek, I use Dropbox all the time and would like to add it right onto my start menu along side the other major shortcuts like Documents, Pictures, etc. It seems like adding Dropbox into the menu should be part of the Dropbox installation package! Sincerely, Dropboxing in Des Moines Dear Dropboxing, We agree, it would be a nice installation option. As it stands you’re going to have to do a little simple hacking to get Dropbox nestled neatly into your start menu. The hack isn’t super elegant but when you’re done you’ll have the link you want and it’ll look like it was there all along. Check out this step-by-step guide here in order to take an existing Library shortcut and rework it to be a Dropbox link. Understanding and Using Symbolic Links Dear How-To Geek, I was talking to a coworker the other day about an issue I’d been having with a media center application I’m running. He suggested using symbolic links to better organize my media and make it easier for the application to access my collection. I had no idea what he was talking about and never got a chance to bug him about it later. Can you clear up this whole symbolic links business for me? I’ve been using computers for years and I’ve never even heard of it! Sincerely, Symbolic Who? Dear Symbolic, Symbolic links aren’t commonly used by many Windows users which is why you likely haven’t run into the concept. Symbolic links are essentially supercharged shortcuts—the newly introduced Windows library system is really just a type of symbolic link system. You can use symbolic links to do all sorts of neat stuff like link folders to your Dropbox folder, organize media, and more. The concept of symbolic links is pretty simple but the execution can be really tricky. We’d suggest reading over our guide to creating symbolic links in Windows 7, Windows XP, and Ubunutu to get a clearer idea what you’re getting into. Rip Your TV DVDs into Handy Episode Files Dear How-To Geek, My wife got me an iPod for Christmas and I still haven’t got around to filling it up. I have tons of entire TV show seasons on DVD and would like to get them on the iPod but I have absolutely no idea where to start. How do I get the shows off the discs? I thought it would be as easy to import the TV shows into iTunes as it is to import tracks off a CD but I was totally wrong. I tried downloading some applications to rip them but those didn’t work at all. Very frustrating! Surely there is an easy and/or automated way to do this, right? Sincerely, Free My DVDs Dear DVDs, Oh man is this a frustration we can relate to. It’s inordinately difficult to get movies and TV shows off physical media and into digital (and portable media player-friendly) formats. There are a multitude of ways to rip DVDs and quite a few applications out there (some good, some mediocre, and some outright malware). We’d recommend a two-part punch to solve your ripping woes. You’ll need a copy of DVDFab to strip away the protections on the discs and rip the disc and Handbrake to load the disc image and convert the files. It’s not quite as smooth as the CD-to-iTunes workflow but it’s still pretty easy. Check out all the steps and settings you’ll want to toggle here. Have a question you want to put before the How-To Geek staff? Shoot us an email at [email protected] and then keep an eye out for a solution in the Ask How-To Geek column. Latest Features How-To Geek ETC Internet Explorer 9 RC Now Available: Here’s the Most Interesting New Stuff Here’s a Super Simple Trick to Defeating Fake Anti-Virus Malware How to Change the Default Application for Android Tasks Stop Believing TV’s Lies: The Real Truth About "Enhancing" Images The How-To Geek Valentine’s Day Gift Guide Inspire Geek Love with These Hilarious Geek Valentines Google’s New Personal Blocklist Extension Kills Search Engine Spam KeyCounter Tracks Your Keystrokes and Mouse Clicks Add Custom LED Ambient Lighting to Your PC or Media Center The Trackor Monitors Amazon Prices; Integrates with Chrome, Firefox, and Safari Four Awesome TRON Legacy Themes for Chrome and Iron Anger is Illogical – Old School Style Instructional Video [Star Trek Mashup]

    Read the article

  • How to Play FLAC Files in Windows 7 Media Center & Player

    - by Mysticgeek
    An annoyance for music lovers who enjoy FLAC format, is there’s no native support for WMP or WMC. If you’re a music enthusiast who prefers FLAC format, we’ll look at adding support to Windows 7 Media Center and Player. For the following article we are using Windows 7 Home Premium 32-bit edition. Download and Install madFLAC v1.8 The first thing we need to do is download and install the madFLAC v1.8 decoder (link below). Just unzip the file and run install.bat… You’ll get a message that it has been successfully registered, click Ok. To verify everything is working, open up one of your FLAC files with WMP, and you’ll get the following message. Check the box Don’t ask me again for this extension and click Yes. Now Media Player should play the track you’ve chosen.   Delete Current Music Library But what if you want to add your entire collection of FLAC files to the Library? If you already have it set up as your default music player, unfortunately we need to remove the current library and delete the database. The best way to manage the music library in Windows 7 is via WMP 12. Since we don’t want to delete songs from the computer we need to Open WMP, press “Alt+T” and navigate to Tools \ Options \ Library.   Now uncheck the box Delete files from computer when deleted from library and click Ok. Now in your Library click “Ctrl + A” to highlight all of the songs in the Library, then hit the “Delete” key. If you have a lot of songs in your library (like on our system) you’ll see the following dialog box while it collects all of the information.   After all of the data is collected, make sure the radio button next to Delete from library only is marked and click Ok. Again you’ll see the Working progress window while the songs are deleted. Deleting Current Database Now we need to make sure we’re starting out fresh. Close out of Media Player, then we’ll basically follow the same directions The Geek pointed out for fixing the WMP Library. Click on Start and type in services.msc into the search box and hit Enter. Now scroll down and stop the service named Windows Media Player Network Sharing Service. Now, navigate to the following directory and the main file to delete CurrentDatabase_372.wmdb %USERPROFILE%\Local Settings\Application Data\Microsoft\Media Player\ Again, the main file to delete is CurrentDatabase_372.wmdb, though if you want, you can delete them all. If you’re uneasy about deleting these files, make sure to back them up first. Now after you restart WMP you can begin adding your FLAC files. For those of us with large collections, it’s extremely annoying to see WMP try to pick up all of your media by default. To delete the other directories go to Organize \ Manage Libraries then open the directories you want to remove. For example here we’re removing the default libraries it tries to check for music. Remove the directories you don’t want it to gather contents from in each of the categories. We removed all of the other collections and only added the FLAC music directory from our home server. SoftPointer Tag Support Plugin Even though we were able to get FLAC files to play in WMP and WMC at this point, there’s another utility from SoftPointer to add. It enables FLAC (and other file formats) to be picked up in the library much easier. It has a long name but is effective –M4a/FLAC/Ogg/Ape/Mpc Tag Support Plugin for Media Player and Media Center (link below). Just install it by accepting the defaults, and you’ll be glad you did. After installing it, and re-launching Media Player, give it some time to collect all of the data from your FLAC directory…it can take a while. In fact, if your collection is huge, just walk away and let it do its thing. If you try to use it right away, WMP slows down considerably while updating the library.   Once the library is setup you’ll be able to play your FLAC tunes in Windows 7 Media Center as well and Windows Media Player 12.   Album Art One caveat is that some of our albums didn’t show any cover art. But we were usually able to get it by right-clicking the album and selecting Find album info.   Then confirming the album information is correct…   Conclusion Although this seems like several steps to go through to play FLAC files in Windows 7 Media Center and Player, it seems to work really well after it’s set up. We haven’t tried this with a 64-bit machine, but the process should be similar, but you might want to make sure the codecs you use are 64-bit. We’re sure there are other methods out there that some of you use, and if so leave us a comment and tell us about it. Download madFlac V1.8  M4a/FLAC/Ogg/Ape/Mpc Tag Support Plugin for Media Player and Media Center from SoftPointer Similar Articles Productive Geek Tips How to Play .OGM Video Files in Windows VistaFixing When Windows Media Player Library Won’t Let You Add FilesUsing Netflix Watchnow in Windows Vista Media Center (Gmedia)Kantaris is a Unique Media Player Based on VLCEasily Change Audio File Formats with XRECODE TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional OutSync will Sync Photos of your Friends on Facebook and Outlook Windows 7 Easter Theme YoWindoW, a real time weather screensaver Optimize your computer the Microsoft way Stormpulse provides slick, real time weather data Geek Parents – Did you try Parental Controls in Windows 7?

    Read the article

  • 8 Mac System Features You Can Access in Recovery Mode

    - by Chris Hoffman
    A Mac’s Recovery Mode is for more than just reinstalling Mac OS X. You’ll find many other useful troubleshooting utilities here — you can use these even if your Mac can’t boot normally. To access Recovery Mode, restart your Mac and press and hold the Command + R keys during the boot-up process. This is one of several hidden startup options on a Mac. Reinstall Mac OS X Most people know Recovery Mode as the place you go to reinstall OS X on your Mac. Recovery Mode will download the OS X installer files from teh Intenret if you don’t have them locally, so they don’t take up space on your disk and you’ll never have to hunt for an opearign system disc. Better yet, it will download up-to-date installation files so you don’t have to spend hours installing operating system updates later. Microsoft could learn a lot from Apple here. Restore From a Time Machine Backup Instead of reinstalling OS X, you can choose to restore your Mac from a time machine backup. This is like restoring a system image on another operating system. You’ll need an external disk containing a backup image created on the current computer to do this. Browse the Web The Get Help Online link opens the Safari web browser to Apple’s documentation site. It’s not limited to Apple’s website, though — you can navigate to any website you like. This feature allows you to access and use a browser on your Mac even if it isn’t booting properly. It’s ideal for looking up troubleshooting information. Manage Your Disks The Disk Utility option opens the same Disk Utility you can access from within Mac OS X. It allows you to partition disks, format them, scan disks for problems, wipe drives, and set up drives in a RAID configuration. If you need to edit partitions from outside your operating system, you can just boot into the recovery environment — you don’t have to download a special partitioning tool and boot into it. Choose the Default Startup Disk Click the Apple menu on the bar at the top of your screen and select Startup Disk to access the Choose Startup Disk tool. Use this tool to choose your computer’s default startup disk and reboot into another operating system. For example, it’s useful if you have Windows installed alongside Mac OS X with Boot Camp. Add or Remove an EFI Firmware Password You can also add a firmware password to your Mac. This works like a BIOS password or UEFI password on a Windows or Linux PC. Click the Utilities menu on the bar at the top of your screen and select Firmware Password Utility to open this tool. Use the tool to turn on a firmware password, which will prevent your computer from starting up from a different hard disk, CD, DVD, or USB drive without the password you provide. This prevents people form booting up your Mac with an unauthorized operating system. If you’ve already enabled a firmware password, you can remove it from here. Use Network Tools to Troubleshoot Your Connection Select Utilities > Network Utility to open a network diagnostic tool. This utility provides a graphical way to view your network connection information. You can also use the netstat, ping, lookup, traceroute, whois, finger, and port scan utilities from here. These can be helpful to troubleshoot Internet connection problems. For example, the ping command can demonstrate whether you can communicate with a remote host and show you if you’re experiencing packet loss, while the traceroute command can show you where a connection is failing if you can’t connect to a remote server. Open a Terminal If you’d like to get your hands dirty, you can select Utilities > Terminal to open a terminal from here. This terminal allows you to do more advanced troubleshooting. Mac OS X uses the bash shell, just as typical Linux distributions do. Most people will just need to use the Reinstall Mac OS X option here, but there are many other tools you can benefit from. If the Recovery Mode files on your Mac are damaged or unavailable, your Mac will automatically download them from Apple so you can use the full recovery environment.

    Read the article

  • WCF AuthenticationService in IIS7 Error

    - by germandb
    I have a WCF Server running on IIS 7 using default application pool, with SSL activate, the services is installed in a SBS Server 2008. I implement client application services with wcf and SQL 2005 for setting the access control in my application. The application run under windows vista and is make with WPF. In my developer machine the application and the WCF services run well, the IIS i'm use for the trials is the local IIS 7 and the database is the SQL Server 2005 database hosting in my server. I'm using Visual Studio Project Designer to enable and configure client application services. using https://localhost/WcfServidorFundacion. When i'm change the authentication services location to https://WcfServices:5659/WcfServidorFundacion and recompile the application, the following error show up. Message: The web service returned the error status code: InternalServerError. Details of service failure: {"Message":" Error while processing your request ","StackTrace":"","ExceptionType":""} Stack Trace: en System.Net.HttpWebRequest.GetResponse() en System.Web.ClientServices.Providers.ProxyHelper.CreateWebRequestAndGetResponse(String serverUri, CookieContainer& cookies, String username, String connectionString, String connectionStringProvider, String[] paramNames, Object[] paramValues, Type returnType) InnerException: System.Net.WebException Message="Remote Server Error: (500) Interal Server Error." I can access the WCF service from the navigator using the url mentioned above and even make a webReference in my project. I make a capture of the response but I'cant post it because i don't have 10 reputation points I activate the error log in the IIS 7 server, and the result is a Warning in the ManagedPipilineHandler. I appreciate if any one can help me Errors & Warnings No.? Severity Event Module Name 132. view trace Warning -MODULE_SET_RESPONSE_ERROR_STATUS ModuleName ManagedPipelineHandler Notification 128 HttpStatus 500 HttpReason Internal Server Error HttpSubStatus 0 ErrorCode 0 ConfigExceptionInfo Notification EXECUTE_REQUEST_HANDLER ErrorCode La operación se ha completado correctamente. (0x0) Maybe this can help, is the web.config of my service <?xml version="1.0" encoding="utf-8"?> <!-- Nota: como alternativa para editar manualmente este archivo, puede utilizar la herramienta Administración de sitios web para configurar los valores de la aplicación. Utilice la opción Sitio Web->Configuración de Asp.Net en Visual Studio. Encontrará una lista completa de valores de configuración y comentarios en machine.config.comments, que se encuentra generalmente en \Windows\Microsoft.Net\Framework\v2.x\Config --> <configuration> <configSections> <sectionGroup name="system.web.extensions" type="System.Web.Configuration.SystemWebExtensionsSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <sectionGroup name="scripting" type="System.Web.Configuration.ScriptingSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="scriptResourceHandler" type="System.Web.Configuration.ScriptingScriptResourceHandlerSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <sectionGroup name="webServices" type="System.Web.Configuration.ScriptingWebServicesSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="jsonSerialization" type="System.Web.Configuration.ScriptingJsonSerializationSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="Everywhere" /> <section name="profileService" type="System.Web.Configuration.ScriptingProfileServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="authenticationService" type="System.Web.Configuration.ScriptingAuthenticationServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="roleService" type="System.Web.Configuration.ScriptingRoleServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> </sectionGroup> </sectionGroup> </sectionGroup> </configSections> <appSettings /> <connectionStrings> <remove name="LocalMySqlServer" /> <remove name="LocalSqlServer" /> <add name="fundacionSelfAut" connectionString="Data Source=FUNDACIONSERVER/PRUEBAS;Initial Catalog=fundacion;User ID=wcfBaseDatos;Password=qwerty_2009;" providerName="System.Data.SqlClient" /> </connectionStrings> <system.web> <profile enabled="true" defaultProvider="SqlProfileProvider"> <providers> <clear /> <add name="SqlProfileProvider" type="System.Web.Profile.SqlProfileProvider" connectionStringName="fundacionSelfAut" applicationName="fundafe" /> </providers> <properties> <add name="FirstName" type="String" /> <add name="LastName" type="String" /> <add name="PhoneNumber" type="String" /> </properties> </profile> <roleManager enabled="true" defaultProvider="SqlRoleProvider"> <providers> <clear /> <add name="SqlRoleProvider" type="System.Web.Security.SqlRoleProvider" connectionStringName="fundacionSelfAut" applicationName="fundafe" /> </providers> </roleManager> <membership defaultProvider="SqlMembershipProvider"> <providers> <clear /> <add name="SqlMembershipProvider" type="System.Web.Security.SqlMembershipProvider" connectionStringName="fundacionSelfAut" applicationName="fundafe" enablePasswordRetrieval="false" enablePasswordReset="false" requiresQuestionAndAnswer="true" requiresUniqueEmail="true" passwordFormat="Hashed" /> </providers> </membership> <authentication mode="Forms" /> <compilation debug="true" strict="false" explicit="true"> <assemblies> <add assembly="System.Core, Version=3.5.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089" /> <add assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </assemblies> </compilation> <!-- La sección <authentication> permite la configuración del modo de autenticación de seguridad utilizado por ASP.NET para identificar a un usuario entrante. --> <!-- La sección <customErrors> permite configurar las acciones que se deben llevar a cabo/cuando un error no controlado tiene lugar durante la ejecución de una solicitud. Específicamente, permite a los desarrolladores configurar páginas de error html que se mostrarán en lugar de un seguimiento de pila de errores. <customErrors mode="RemoteOnly" defaultRedirect="GenericErrorPage.htm"> <error statusCode="403" redirect="NoAccess.htm" /> <error statusCode="404" redirect="FileNotFound.htm" /> </customErrors> --> <pages> <controls> <add tagPrefix="asp" namespace="System.Web.UI" assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </controls> </pages> <httpHandlers> <remove verb="*" path="*.asmx" /> <add verb="*" path="*.asmx" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add verb="*" path="*_AppService.axd" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" validate="false" /> </httpHandlers> <httpModules> <add name="ScriptModule" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </httpModules> <sessionState timeout="40" /> </system.web> <system.codedom> <compilers> <compiler language="c#;cs;csharp" extension=".cs" warningLevel="4" type="Microsoft.CSharp.CSharpCodeProvider, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"> <providerOption name="CompilerVersion" value="v3.5" /> <providerOption name="WarnAsError" value="false" /> </compiler> </compilers> </system.codedom> <!-- La sección webServer del sistema es necesaria para ejecutar ASP.NET AJAX en Internet Information Services 7.0. Sin embargo, no es necesaria para la versión anterior de IIS. --> <system.webServer> <validation validateIntegratedModeConfiguration="false" /> <modules> <add name="ScriptModule" preCondition="integratedMode" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </modules> <handlers> <remove name="WebServiceHandlerFactory-Integrated" /> <add name="ScriptHandlerFactory" verb="*" path="*.asmx" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="ScriptHandlerFactoryAppServices" verb="*" path="*_AppService.axd" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> <add name="ScriptResource" preCondition="integratedMode" verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" /> </handlers> <tracing> <traceFailedRequests> <add path="*"> <traceAreas> <add provider="ASP" verbosity="Verbose" /> <add provider="ASPNET" areas="Infrastructure,Module,Page,AppServices" verbosity="Verbose" /> <add provider="ISAPI Extension" verbosity="Verbose" /> <add provider="WWW Server" areas="Authentication,Security,Filter,StaticFile,CGI,Compression,Cache,RequestNotifications,Module" verbosity="Verbose" /> </traceAreas> <failureDefinitions statusCodes="401.3,500,403,404,405" /> </add> </traceFailedRequests> </tracing> <security> <authorization> <add accessType="Allow" users="germanbarbosa,informatica" /> </authorization> <authentication> <windowsAuthentication enabled="false" /> </authentication> </security> </system.webServer> <system.web.extensions> <scripting> <webServices> <authenticationService enabled="true" requireSSL="true" /> <profileService enabled="true" readAccessProperties="FirstName,LastName,PhoneNumber" /> <roleService enabled="true" /> </webServices> </scripting> </system.web.extensions> <system.serviceModel> <services> <!-- this enables the WCF AuthenticationService endpoint --> <service behaviorConfiguration="AppServiceBehaviors" name="System.Web.ApplicationServices.AuthenticationService"> <endpoint address="" binding="basicHttpBinding" bindingConfiguration="userHttps" bindingNamespace="http://asp.net/ApplicationServices/v200" contract="System.Web.ApplicationServices.AuthenticationService" /> </service> <!-- this enables the WCF RoleService endpoint --> <service behaviorConfiguration="AppServiceBehaviors" name="System.Web.ApplicationServices.RoleService"> <endpoint binding="basicHttpBinding" bindingConfiguration="userHttps" bindingNamespace="http://asp.net/ApplicationServices/v200" contract="System.Web.ApplicationServices.RoleService" /> </service> <!-- this enables the WCF ProfileService endpoint --> <service behaviorConfiguration="AppServiceBehaviors" name="System.Web.ApplicationServices.ProfileService"> <endpoint binding="basicHttpBinding" bindingNamespace="http://asp.net/ApplicationServices/v200" bindingConfiguration="userHttps" contract="System.Web.ApplicationServices.ProfileService" /> </service> </services> <bindings> <basicHttpBinding> <!-- Set up a binding that uses Username as the client credential type --> <binding name="userHttps"> <security mode="Transport"> </security> </binding> </basicHttpBinding> </bindings> <behaviors> <serviceBehaviors> <behavior name="AppServiceBehaviors"> <serviceMetadata httpGetEnabled="false" httpsGetEnabled="true" /> <serviceDebug includeExceptionDetailInFaults="true" /> <serviceAuthorization principalPermissionMode="UseAspNetRoles" roleProviderName="SqlRoleProvider" /> <serviceCredentials> <userNameAuthentication userNamePasswordValidationMode="MembershipProvider" membershipProviderName="SqlMembershipProvider" /> </serviceCredentials> </behavior> </serviceBehaviors> </behaviors> <serviceHostingEnvironment aspNetCompatibilityEnabled="true" /> </system.serviceModel> </configuration>

    Read the article

  • Oracle Open World 2012: SQL Developer Recap

    - by thatjeffsmith
    Last week was the ‘big show’ in San Francisco. I was very happy to meet many of you in person. And many of you had questions – lots of questions! We had full or overflowing rooms for our sessions and hands-on-labs. The SQL Developer ‘booths’ were also slammed several times. So exciting to see so many of YOU excited about SQL Developer. It’s very cool to hear the stories of our tools saving you and your organizations so much time (and money!) Instead of doing a Day 0 – Day 9 recap, I thought I’d share with you the questions that I heard more than once. And just for giggles, I’ll throw in some answers as well So in no particular order… What’s the difference between Oracle SQL Developer & Oracle SQL Developer Data Modeler? Mathematically speaking – two words. But as far as the actual modeling features go, there’s no difference between the two applications. The same ‘code’ or features as it pertains to data modeling and design are in both tools. However, in SQL Developer you have all of the OTHER features fighting for real estate in the UI. So I have a general rule of thumb – if you spend MOST of your time in the database, use SQL Developer. And if you spend most of your time in the data model, run the separate and dedicated program, Oracle SQL Developer Data Modeler. Here’s a couple of screenshots to drive home the UI point: Oracle SQL Developer Oracle SQL Developer Data Modeler running INSIDE of SQL Developer. Notice how the Modeler menu items fold under the file menu? Oracle SQL Developer Data Modeler Easier to navigate and manipulate your models with the stand alone modeler. Just no worksheet to run your ad-hoc queries, etc. Don’t forget you can disable the Data Modeler inside of SQL Developer via the Extensions preference page. How can I model my table partitions? Partitioning is defined via the Physical model. So after you have finished your relational model, you need to generate a physical model. Oracle SQL Developer Data Modeler Physical Model and Partitioning Open the properties for your physical model table. Enable the ‘partitioned’ property. Once you do so, the ‘Partitioning’ page will activate. Lots and lots of partitioning support and options here But what about Interval Partitioning? An extension of range partitioning in 11gR2, we don’t currently support this partitioning scheme in SQL Developer. But we’re working on it! Can SQL Developer ignore column order when comparing models? Yes! After you start a model compare, one of your options is to disregard the order of an attribute or column definition. Tell SQL Developer you don’t care when your column shows up, just as long as it DOES show up. Wow, you got a lot of questions around modeling! Is that normal? Yes! While we appreciate that many folks inherit their applications and associated designs, new applications are being ‘born’ every day. Since both of our tools are free for anyone to design their new Oracle applications with, we attract a fair amount of attention I want to do a Hands On Lab. How do I get your software and instructional guides? Go here. Download VirtualBox. Then download the VB image. Import the appliance. Start it. Connect oracle/oracle on the OEL VM. Click on ‘Start Here’ in the desktop. Follow the instructions. If you need help, ask away! You went too fast in your Tips & Tricks session. Do you have cliff notes? Yes! And you’re SO close to finding them! Just go to my SQL Developer resources page. All of my tips are documented on this blog somewhere. I’ve indexed the most popular ones on the resource page. You can use the Search dialog on the right to find the rest. Or just send me a comment or question, and I’ll do my best to answer them as they come in.

    Read the article

  • Pure Server-Side Filtering with RadGridView and WCF RIA Services

    Those of you who are familiar with WCF RIA Services know that the DomainDataSource control provides a FilterDescriptors collection that enables you to filter data returned by the query on the server. We have been using this DomainDataSource feature in our RIA Services with DomainDataSource online example for almost an year now. In the example, we are listening for RadGridViews Filtering event in order to intercept any filtering that is performed on the client and translate it to something that the DomainDataSource will understand, in this case a System.Windows.Data.FilterDescriptor being added or removed from its FilterDescriptors collection. Think of RadGridView.FilterDescriptors as client-side filtering and of DomainDataSource.FilterDescriptors as server-side filtering. We no longer need the client-side one. With the introduction of the Custom Filtering Controls feature many new possibilities have opened. With these custom controls we no longer need to do any filtering on the client. I have prepared a very small project that demonstrates how to filter solely on the server by using a custom filtering control. As I have already mentioned filtering on the server is done through the FilterDescriptors collection of the DomainDataSource control. This collection holds instances of type System.Windows.Data.FilterDescriptor. The FilterDescriptor has three important properties: PropertyPath: Specifies the name of the property that we want to filter on (the left operand). Operator: Specifies the type of comparison to use when filtering. An instance of FilterOperator Enumeration. Value: The value to compare with (the right operand). An instance of the Parameter Class. By adding filters, you can specify that only entities which meet the condition in the filter are loaded from the domain context. In case you are not familiar with these concepts you might find Brad Abrams blog interesting. Now, our requirements are to create some kind of UI that will manipulate the DomainDataSource.FilterDescriptors collection. When it comes to collections, my first choice of course would be RadGridView. If you are not familiar with the Custom Filtering Controls concept I would strongly recommend getting acquainted with my step-by-step tutorial Custom Filtering with RadGridView for Silverlight and checking the online example out. I have created a simple custom filtering control that contains a RadGridView and several buttons. This control is aware of the DomainDataSource instance, since it is operating on its FilterDescriptors collection. In fact, the RadGridView that is inside it is bound to this collection. In order to display filters that are relevant for the current column only, I have applied a filter to the grid. This filter is a Telerik.Windows.Data.FilterDescriptor and is used to filter the little grid inside the custom control. It should not be confused with the DomainDataSource.FilterDescriptors collection that RadGridView is actually bound to. These are the RIA filters. Additionally, I have added several other features. For example, if you have specified a DataFormatString on your original column, the Value column inside the custom control will pick it up and format the filter values accordingly. Also, I have transferred the data type of the column that you are filtering to the Value column of the custom control. This will help the little RadGridView determine what kind of editor to show up when you begin edit, for example a date picker for DateTime columns. Finally, I have added four buttons two of them can be used to add or remove filters and the other two will communicate the changes you have made to the server. Here is the full source code of the DomainDataSourceFilteringControl. The XAML: <UserControl x:Class="PureServerSideFiltering.DomainDataSourceFilteringControl"    xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation"    xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml"     xmlns:telerikGrid="clr-namespace:Telerik.Windows.Controls;assembly=Telerik.Windows.Controls.GridView"     xmlns:telerik="clr-namespace:Telerik.Windows.Controls;assembly=Telerik.Windows.Controls"     Width="300">     <Border x:Name="LayoutRoot"             BorderThickness="1"             BorderBrush="#FF8A929E"             Padding="5"             Background="#FFDFE2E5">           <Grid>             <Grid.RowDefinitions>                 <RowDefinition Height="Auto"/>                 <RowDefinition Height="150"/>                 <RowDefinition Height="Auto"/>             </Grid.RowDefinitions>               <StackPanel Grid.Row="0"                         Margin="2"                         Orientation="Horizontal"                         HorizontalAlignment="Center">                 <telerik:RadButton Name="addFilterButton"                                   Click="OnAddFilterButtonClick"                                   Content="Add Filter"                                   Margin="2"                                   Width="96"/>                 <telerik:RadButton Name="removeFilterButton"                                   Click="OnRemoveFilterButtonClick"                                   Content="Remove Filter"                                   Margin="2"                                   Width="96"/>             </StackPanel>               <telerikGrid:RadGridView Name="filtersGrid"                                     Grid.Row="1"                                     Margin="2"                                     ItemsSource="{Binding FilterDescriptors}"                                     AddingNewDataItem="OnFilterGridAddingNewDataItem"                                     ColumnWidth="*"                                     ShowGroupPanel="False"                                     AutoGenerateColumns="False"                                     CanUserResizeColumns="False"                                     CanUserReorderColumns="False"                                     CanUserFreezeColumns="False"                                     RowIndicatorVisibility="Collapsed"                                     IsFilteringAllowed="False"                                     CanUserSortColumns="False">                 <telerikGrid:RadGridView.Columns>                     <telerikGrid:GridViewComboBoxColumn DataMemberBinding="{Binding Operator}"                                                         UniqueName="Operator"/>                     <telerikGrid:GridViewDataColumn Header="Value"                                                     DataMemberBinding="{Binding Value.Value}"                                                     UniqueName="Value"/>                 </telerikGrid:RadGridView.Columns>             </telerikGrid:RadGridView>               <StackPanel Grid.Row="2"                         Margin="2"                         Orientation="Horizontal"                         HorizontalAlignment="Center">                 <telerik:RadButton Name="filterButton"                                   Click="OnApplyFiltersButtonClick"                                   Content="Apply Filters"                                   Margin="2"                                   Width="96"/>                 <telerik:RadButton Name="clearButton"                                   Click="OnClearFiltersButtonClick"                                   Content="Clear Filters"                                   Margin="2"                                   Width="96"/>             </StackPanel>           </Grid>       </Border> </UserControl>   And the code-behind: using System; using System.Collections.Generic; using System.Linq; using System.Net; using System.Windows; using System.Windows.Controls; using System.Windows.Documents; using System.Windows.Input; using System.Windows.Media; using System.Windows.Media.Animation; using System.Windows.Shapes; using Telerik.Windows.Controls.GridView; using System.Windows.Data; using Telerik.Windows.Controls; using Telerik.Windows.Data;   namespace PureServerSideFiltering {     /// <summary>     /// A custom filtering control capable of filtering purely server-side.     /// </summary>     public partial class DomainDataSourceFilteringControl : UserControl, IFilteringControl     {         // The main player here.         DomainDataSource domainDataSource;           // This is the name of the property that this column displays.         private string dataMemberName;           // This is the type of the property that this column displays.         private Type dataMemberType;           /// <summary>         /// Identifies the <see cref="IsActive"/> dependency property.         /// </summary>         /// <remarks>         /// The state of the filtering funnel (i.e. full or empty) is bound to this property.         /// </remarks>         public static readonly DependencyProperty IsActiveProperty =             DependencyProperty.Register(                 "IsActive",                 typeof(bool),                 typeof(DomainDataSourceFilteringControl),                 new PropertyMetadata(false));           /// <summary>         /// Gets or sets a value indicating whether the filtering is active.         /// </summary>         /// <remarks>         /// Set this to true if you want to lit-up the filtering funnel.         /// </remarks>         public bool IsActive         {             get { return (bool)GetValue(IsActiveProperty); }             set { SetValue(IsActiveProperty, value); }         }           /// <summary>         /// Gets or sets the domain data source.         /// We need this in order to work on its FilterDescriptors collection.         /// </summary>         /// <value>The domain data source.</value>         public DomainDataSource DomainDataSource         {             get { return this.domainDataSource; }             set { this.domainDataSource = value; }         }           public System.Windows.Data.FilterDescriptorCollection FilterDescriptors         {             get { return this.DomainDataSource.FilterDescriptors; }         }           public DomainDataSourceFilteringControl()         {             InitializeComponent();         }           public void Prepare(GridViewBoundColumnBase column)         {             this.LayoutRoot.DataContext = this;               if (this.DomainDataSource == null)             {                 // Sorry, but we need a DomainDataSource. Can't do anything without it.                 return;             }               // This is the name of the property that this column displays.             this.dataMemberName = column.GetDataMemberName();               // This is the type of the property that this column displays.             // We need this in order to see which FilterOperators to feed to the combo-box column.             this.dataMemberType = column.DataType;               // We will use our magic Type extension method to see which operators are applicable for             // this data type. You can go to the extension method body and see what it does.             ((GridViewComboBoxColumn)this.filtersGrid.Columns["Operator"]).ItemsSource                 = this.dataMemberType.ApplicableFilterOperators();               // This is very nice as well. We will tell the Value column its data type. In this way             // RadGridView will pick up the best editor according to the data type. For example,             // if the data type of the value is DateTime, you will be editing it with a DatePicker.             // Nice!             ((GridViewDataColumn)this.filtersGrid.Columns["Value"]).DataType = this.dataMemberType;               // Yet another nice feature. We will transfer the original DataFormatString (if any) to             // the Value column. In this way if you have specified a DataFormatString for the original             // column, you will see all filter values formatted accordingly.             ((GridViewDataColumn)this.filtersGrid.Columns["Value"]).DataFormatString = column.DataFormatString;               // This is important. Since our little filtersGrid will be bound to the entire collection             // of this.domainDataSource.FilterDescriptors, we need to set a Telerik filter on the             // grid so that it will display FilterDescriptor which are relevane to this column ONLY!             Telerik.Windows.Data.FilterDescriptor columnFilter = new Telerik.Windows.Data.FilterDescriptor("PropertyPath"                 , Telerik.Windows.Data.FilterOperator.IsEqualTo                 , this.dataMemberName);             this.filtersGrid.FilterDescriptors.Add(columnFilter);               // We want to listen for this in order to activate and de-activate the UI funnel.             this.filtersGrid.Items.CollectionChanged += this.OnFilterGridItemsCollectionChanged;         }           /// <summary>         // Since the DomainDataSource is a little bit picky about adding uninitialized FilterDescriptors         // to its collection, we will prepare each new instance with some default values and then         // the user can change them later. Go to the event handler to see how we do this.         /// </summary>         void OnFilterGridAddingNewDataItem(object sender, GridViewAddingNewEventArgs e)         {             // We need to initialize the new instance with some values and let the user go on from here.             System.Windows.Data.FilterDescriptor newFilter = new System.Windows.Data.FilterDescriptor();               // This is a must. It should know what member it is filtering on.             newFilter.PropertyPath = this.dataMemberName;               // Initialize it with one of the allowed operators.             // TypeExtensions.ApplicableFilterOperators method for more info.             newFilter.Operator = this.dataMemberType.ApplicableFilterOperators().First();               if (this.dataMemberType == typeof(DateTime))             {                 newFilter.Value.Value = DateTime.Now;             }             else if (this.dataMemberType == typeof(string))             {                 newFilter.Value.Value = "<enter text>";             }             else if (this.dataMemberType.IsValueType)             {                 // We need something non-null for all value types.                 newFilter.Value.Value = Activator.CreateInstance(this.dataMemberType);             }               // Let the user edit the new filter any way he/she likes.             e.NewObject = newFilter;         }           void OnFilterGridItemsCollectionChanged(object sender, System.Collections.Specialized.NotifyCollectionChangedEventArgs e)         {             // We are active only if we have any filters define. In this case the filtering funnel will lit-up.             this.IsActive = this.filtersGrid.Items.Count > 0;         }           private void OnApplyFiltersButtonClick(object sender, RoutedEventArgs e)         {             if (this.DomainDataSource.IsLoadingData)             {                 return;             }               // Comment this if you want the popup to stay open after the button is clicked.             this.ClosePopup();               // Since this.domainDataSource.AutoLoad is false, this will take into             // account all filtering changes that the user has made since the last             // Load() and pull the new data to the client.             this.DomainDataSource.Load();         }           private void OnClearFiltersButtonClick(object sender, RoutedEventArgs e)         {             if (this.DomainDataSource.IsLoadingData)             {                 return;             }               // We want to remove ONLY those filters from the DomainDataSource             // that this control is responsible for.             this.DomainDataSource.FilterDescriptors                 .Where(fd => fd.PropertyPath == this.dataMemberName) // Only "our" filters.                 .ToList()                 .ForEach(fd => this.DomainDataSource.FilterDescriptors.Remove(fd)); // Bye-bye!               // Comment this if you want the popup to stay open after the button is clicked.             this.ClosePopup();               // After we did our housekeeping, get the new data to the client.             this.DomainDataSource.Load();         }           private void OnAddFilterButtonClick(object sender, RoutedEventArgs e)         {             if (this.DomainDataSource.IsLoadingData)             {                 return;             }               // Let the user enter his/or her requirements for a new filter.             this.filtersGrid.BeginInsert();             this.filtersGrid.UpdateLayout();         }           private void OnRemoveFilterButtonClick(object sender, RoutedEventArgs e)         {             if (this.DomainDataSource.IsLoadingData)             {                 return;             }               // Find the currently selected filter and destroy it.             System.Windows.Data.FilterDescriptor filterToRemove = this.filtersGrid.SelectedItem as System.Windows.Data.FilterDescriptor;             if (filterToRemove != null                 && this.DomainDataSource.FilterDescriptors.Contains(filterToRemove))             {                 this.DomainDataSource.FilterDescriptors.Remove(filterToRemove);             }         }           private void ClosePopup()         {             System.Windows.Controls.Primitives.Popup popup = this.ParentOfType<System.Windows.Controls.Primitives.Popup>();             if (popup != null)             {                 popup.IsOpen = false;             }         }     } }   Finally, we need to tell RadGridViews Columns to use this custom control instead of the default one. Here is how to do it: using System; using System.Collections.Generic; using System.Linq; using System.Net; using System.Windows; using System.Windows.Controls; using System.Windows.Documents; using System.Windows.Input; using System.Windows.Media; using System.Windows.Media.Animation; using System.Windows.Shapes; using System.Windows.Data; using Telerik.Windows.Data; using Telerik.Windows.Controls; using Telerik.Windows.Controls.GridView;   namespace PureServerSideFiltering {     public partial class MainPage : UserControl     {         public MainPage()         {             InitializeComponent();             this.grid.AutoGeneratingColumn += this.OnGridAutoGeneratingColumn;               // Uncomment this if you want the DomainDataSource to start pre-filtered.             // You will notice how our custom filtering controls will correctly read this information,             // populate their UI with the respective filters and lit-up the funnel to indicate that             // filtering is active. Go ahead and try it.             this.employeesDataSource.FilterDescriptors.Add(new System.Windows.Data.FilterDescriptor("Title", System.Windows.Data.FilterOperator.Contains, "Assistant"));             this.employeesDataSource.FilterDescriptors.Add(new System.Windows.Data.FilterDescriptor("HireDate", System.Windows.Data.FilterOperator.IsGreaterThan, new DateTime(1998, 12, 31)));             this.employeesDataSource.FilterDescriptors.Add(new System.Windows.Data.FilterDescriptor("HireDate", System.Windows.Data.FilterOperator.IsLessThanOrEqualTo, new DateTime(1999, 12, 31)));               this.employeesDataSource.Load();         }           /// <summary>         /// First of all, we will need to replace the default filtering control         /// of each column with out custom filtering control DomainDataSourceFilteringControl         /// </summary>         private void OnGridAutoGeneratingColumn(object sender, GridViewAutoGeneratingColumnEventArgs e)         {             GridViewBoundColumnBase dataColumn = e.Column as GridViewBoundColumnBase;             if (dataColumn != null)             {                 // We do not like ugly dates.                 if (dataColumn.DataType == typeof(DateTime))                 {                     dataColumn.DataFormatString = "{0:d}"; // Short date pattern.                       // Notice how this format will be later transferred to the Value column                     // of the grid that we have inside the DomainDataSourceFilteringControl.                 }                   // Replace the default filtering control with our.                 dataColumn.FilteringControl = new DomainDataSourceFilteringControl()                 {                     // Let the control know about the DDS, after all it will work directly on it.                     DomainDataSource = this.employeesDataSource                 };                   // Finally, lit-up the filtering funnel through the IsActive dependency property                 // in case there are some filters on the DDS that match our column member.                 string dataMemberName = dataColumn.GetDataMemberName();                 dataColumn.FilteringControl.IsActive =                     this.employeesDataSource.FilterDescriptors                     .Where(fd => fd.PropertyPath == dataMemberName)                     .Count() > 0;             }         }     } } The best part is that we are not only writing filters for the DomainDataSource we can read and load them. If the DomainDataSource has some pre-existing filters (like I have created in the code above), our control will read them and will populate its UI accordingly. Even the filtering funnel will light-up! Remember, the funnel is controlled by the IsActive property of our control. While this is just a basic implementation, the source code is absolutely yours and you can take it from here and extend it to match your specific business requirements. Below the main grid there is another debug grid. With its help you can monitor what filter descriptors are added and removed to the domain data source. Download Source Code. (You will have to have the AdventureWorks sample database installed on the default SQLExpress instance in order to run it.) Enjoy!Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

    Read the article

  • Lubuntu 13.10 unable to connect to cups localhost:631

    - by user142139
    I am using Lubuntu 13.10 (recently upgraded) and am trying to print to a network printer (HP photosmart 7960) through my router (US Robotics 5461). My printer is connected to the router via USB cable. Normally, I would use the cups configuration interface to set up the wireless connection to the printer. I was able to use the printer through the router wirelessly, using Ubuntu 12.04. Now, with my recently upgraded Lubuntu 13.10, I am unable to get the Cups config webpage (http://localhost:631) to come up. In Chromium, I get: This web page is not available. In Firefox, I get: Unable to connect. Firefox can't establish a connection to the server at localhost:631. The CUPS config file details are below. I have this website to help with the router connections for Linux: http://www.usr.com/support/5461/5461-files/printer_installation_linux/index.html My printer's address through the router is: http://192.168.2.1:1631/printers/My_Printer Can you tell me how to fix this? Or, what to add to the cups configuration file to make this work? Please help. Thanks psychicnut CUPS CONFIG FILE DETAILS: # Show general information in error_log. LogLevel warn MaxLogSize 0 SystemGroup lpadmin Listen /var/run/cups/cups.sock Listen /var/run/cups/cups.sock Listen 192.168.2.1:1631 Browsing Off BrowseLocalProtocols dnssd DefaultAuthType Basic WebInterface Yes <Location /> Order allow,deny </Location> <Location /admin> Order allow,deny </Location> <Location /admin/conf> AuthType Default Require user @SYSTEM Order allow,deny </Location> <Policy default> JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default <Limit Create-Job Print-Job Print-URI Validate-Job> Order deny,allow </Limit> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job Cancel-My-Jobs Close-Job CUPS-Move-Job CUPS-Get-Document> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default CUPS-Get-Devices> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After Cancel-Jobs CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy> <Policy authenticated> JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default <Limit Create-Job Print-Job Print-URI Validate-Job> AuthType Default Order deny,allow </Limit> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job Cancel-My-Jobs Close-Job CUPS-Move-Job CUPS-Get-Document> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After Cancel-Jobs CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Cancel-Job CUPS-Authenticate-Job> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy> JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default

    Read the article

  • Bluetooth DUN Tethering fails

    - by tacone
    I have an HTC Desire HD, with Android Froyo (2.2) and PDANet installed. I am using Ubuntu 10.10. I cannot tether it over Bluetooth either with Network Manager or BlueMan. (note, I installed Blueman only after failing with NetWork manager, and I even tried the last version from the PPA). With both my device is discovered, paired, setup. But connecting always fail. Network manager says it cannot get the details of my device Blueman says Connection Refused (111) Here are some relevant entries from syslog. Mar 11 22:13:00 tacone-macbook bluetoothd[2242]: Bluetooth deamon 4.69 Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Starting SDP server Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Starting experimental netlink support Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Failed to find Bluetooth netlink family Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Failed to init netlink plugin Mar 11 22:13:00 tacone-macbook kernel: [ 158.284357] Bluetooth: L2CAP ver 2.14 Mar 11 22:13:00 tacone-macbook kernel: [ 158.284361] Bluetooth: L2CAP socket layer initialized Mar 11 22:13:00 tacone-macbook kernel: [ 158.446781] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Mar 11 22:13:00 tacone-macbook kernel: [ 158.446784] Bluetooth: BNEP filters: protocol multicast Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: HCI dev 0 registered Mar 11 22:13:00 tacone-macbook kernel: [ 158.569481] Bluetooth: SCO (Voice Link) ver 0.6 Mar 11 22:13:00 tacone-macbook kernel: [ 158.569484] Bluetooth: SCO socket layer initialized Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: HCI dev 0 up Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Starting security manager 0 Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: ioctl(HCIUNBLOCKADDR): Invalid argument (22) Mar 11 22:13:00 tacone-macbook kernel: [ 158.818600] Bluetooth: RFCOMM TTY layer initialized Mar 11 22:13:00 tacone-macbook kernel: [ 158.818607] Bluetooth: RFCOMM socket layer initialized Mar 11 22:13:00 tacone-macbook kernel: [ 158.818610] Bluetooth: RFCOMM ver 1.11 Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: probe failed with driver input-headset for device /org/bluez/2242/hci0/dev_F8_DB_7F_AF_6B_EE Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Adapter /org/bluez/2242/hci0 has been enabled Mar 11 22:13:00 tacone-macbook pulseaudio[1757]: bluetooth-util.c: Error from ListDevices reply: org.freedesktop.DBus.Error.AccessDenied Mar 11 22:13:00 tacone-macbook NetworkManager[1247]: <warn> bluez error getting adapter properties: Rejected send message, 1 matched rules; type="method_call", sender=":1.4" (uid=0 pid=1247 comm="NetworkManager) interface="org.bluez.Adapter" member="GetProperties" error name="(unset)" requested_reply=0 destination="org.bluez" (uid=0 pid=2242 comm="/usr/sbin/bluetoothd)) Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: return_link_keys (sba=00:23:6C:B5:03:6F, dba=00:23:6C:C0:F1:B0) Mar 11 22:13:00 tacone-macbook pulseaudio[1757]: bluetooth-util.c: Error from GetProperties reply: org.freedesktop.DBus.Error.AccessDenied Mar 11 22:15:02 tacone-macbook bluetoothd[2243]: Discovery session 0x2262d7c0 with :1.45 activated Mar 11 22:15:15 tacone-macbook bluetoothd[2243]: Stopping discovery Mar 11 22:15:15 tacone-macbook pulseaudio[1757]: bluetooth-util.c: Error from GetProperties reply: org.freedesktop.DBus.Error.AccessDenied Mar 11 22:15:16 tacone-macbook bluetoothd[2243]: link_key_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:15:16 tacone-macbook bluetoothd[2243]: io_capa_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:15:17 tacone-macbook bluetoothd[2243]: io_capa_response (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:15:18 tacone-macbook bluetoothd[2243]: Stopping discovery Mar 11 22:15:28 tacone-macbook bluetoothd[2243]: link_key_notify (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE, type=5) Mar 11 22:15:28 tacone-macbook kernel: [ 306.585725] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:15:28 tacone-macbook kernel: [ 306.630757] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:15:28 tacone-macbook bluetoothd[2243]: Authentication requested Mar 11 22:15:28 tacone-macbook bluetoothd[2243]: link_key_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:15:28 tacone-macbook kernel: [ 306.784829] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:15:28 tacone-macbook kernel: [ 306.857861] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:15:29 tacone-macbook bluetoothd[2243]: probe failed with driver input-headset for device /org/bluez/2242/hci0/dev_F8_DB_7F_AF_6B_EE Mar 11 22:15:29 tacone-macbook pulseaudio[1757]: bluetooth-util.c: Error from GetProperties reply: org.freedesktop.DBus.Error.AccessDenied Mar 11 22:15:29 tacone-macbook pulseaudio[1757]: last message repeated 8 times Mar 11 22:15:29 tacone-macbook bluetoothd[2243]: Stopping discovery Mar 11 22:15:30 tacone-macbook modem-manager: (tty/rfcomm0): could not get port's parent device Mar 11 22:15:30 tacone-macbook modem-manager: (rfcomm0) opening serial device... Mar 11 22:15:30 tacone-macbook modem-manager: (rfcomm0): probe requested by plugin 'Generic' Mar 11 22:15:43 tacone-macbook modem-manager: (rfcomm0) closing serial device... Mar 11 22:15:43 tacone-macbook modem-manager: (rfcomm0) opening serial device... Mar 11 22:15:49 tacone-macbook modem-manager: (rfcomm0) closing serial device... Mar 11 22:16:15 tacone-macbook modem-manager: (tty/rfcomm0): could not get port's parent device Mar 11 22:16:19 tacone-macbook kernel: [ 357.375108] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook bluetoothd[2243]: link_key_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:16:24 tacone-macbook kernel: [ 362.169506] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook kernel: [ 362.215529] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook bluetoothd[2243]: link_key_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:16:24 tacone-macbook kernel: [ 362.281559] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook kernel: [ 362.330588] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook modem-manager: (tty/rfcomm0): could not get port's parent device Any help ? PS: tethering via USB or WiFi is not an option, I need to do it over Bluetooth.

    Read the article

  • How To Replace Notepad in Windows 7

    - by Trevor Bekolay
    It used to be that Notepad was a necessary evil because it started up quickly and let us catch a quick glimpse of plain text files. Now, there are a bevy of capable Notepad replacements that are just as fast, but also have great feature sets. Before following the rest of this how-to, ensure that you’re logged into an account with Administrator access. Note: The following instructions involve modifying some Windows system folders. Don’t mess anything up while you’re in there! If you follow our instructions closely, you’ll be fine. Choose your replacement There are a ton of great Notepad replacements, including Notepad2, Metapad, and Notepad++. The best one for you will depend on what types of text files you open and what you do with them. We’re going to use Notepad++ in this how-to. The first step is to find the executable file that you’ll replace Notepad with. Usually this will be the only file with the .exe file extension in the folder where you installed your text editor. Copy the executable file to your desktop and try to open it, to make sure that it works when opened from a different folder. In the Notepad++ case, a special little .exe file is available for the explicit purpose of replacing Notepad.If we run it from the desktop, it opens up Notepad++ in all its glory. Back up Notepad You will probably never go back once you switch, but you never know. You can backup Notepad to a special location if you’d like, but we find it’s easiest to just keep a backed up copy of Notepad in the folders it was originally located. In Windows 7, Notepad resides in: C:\Windows C:\Windows\System32 C:\Windows\SysWOW64 in 64-bit versions only Navigate to each of those directories and copy Notepad. Paste it into the same folder. If prompted, choose to Copy, but keep both files. You can keep your backup as “notepad (2).exe”, but we prefer to rename it to “notepad.exe.bak”. Do this for all of the folders that have Notepad (2 total for 32-bit Windows 7, 3 total for 64-bit). Take control of Notepad and delete it Even if you’re on an administrator account, you can’t just delete Notepad – Microsoft has made some security gains in this respect. Fortunately for us, it’s still possible to take control of a file and delete it without resorting to nasty hacks like disabling UAC. Navigate to one of the directories that contain Notepad. Right-click on it and select Properties.   Switch to the Security tab, then click on the Advanced button. Note that the owner of the file is a user called “TrustedInstaller”. You can’t do much with files owned by TrustedInstaller, so let’s take control of it. Click the Edit… button. Select the desired owner (you could choose your own account, but we’re going to give any Administrator control) and click OK. You’ll get a message that you need to close and reopen the Properties windows to edit permissions. Before doing that, confirm that the owner has changed to what you selected. Click OK, then OK again to close the Properties window. Right-click on Notepad and click on Properties again. Switch to the Security tab. Click on Edit…. Select the appropriate group or user name in the list at the top, then add a checkmark in the checkbox beside Full control in the Allow column. Click OK, then Yes to the dialog box that pops up. Click OK again to close the Properties window. Now you can delete Notepad, by either selecting it and pressing Delete on the keyboard, or right-click on it and click Delete.   You’re now free from Notepad’s foul clutches! Repeat this procedure for the remaining folders (or folder, on 32-bit Windows 7). Drop in your replacement Copy your Notepad replacement’s executable, which should still be on your desktop. Browse to the two or three folders listed above and copy your .exe to those locations. If prompted for Administrator permission, click Continue. If your executable file was named something other than “notepad.exe”, rename it to “notepad.exe”. Don’t be alarmed if the thumbnail still shows the old Notepad icon. Double click on Notepad and your replacement should open. To make doubly sure that it works, press Win+R to bring up the Run dialog box and enter “notepad” into the text field. Press enter or click OK. Now you can allow Windows to open files with Notepad by default with little to no shame! All without restarting or having to disable UAC! Similar Articles Productive Geek Tips Search and Replace Specific Formatting (fonts, styles,etc) in Microsoft WordHow to Drag Files to the Taskbar to Open Them in Windows 7Customize the Windows 7 or Vista Send To MenuKill Processes from the Windows Command LineChange Your Windows 7 Library Icons the Easy Way TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Use My TextTools to Edit and Organize Text Discovery Channel LIFE Theme (Win7) Increase the size of Taskbar Previews (Win 7) Scan your PC for nasties with Panda ActiveScan CleanMem – Memory Cleaner AceStock – The Personal Stock Monitor

    Read the article

  • Using C# 4.0’s DynamicObject as a Stored Procedure Wrapper

    - by EltonStoneman
    [Source: http://geekswithblogs.net/EltonStoneman] Overview Ignoring the fashion, I still make a lot of use of DALs – typically when inheriting a codebase with an established database schema which is full of tried and trusted stored procedures. In the DAL a collection of base classes have all the scaffolding, so the usual pattern is to create a wrapper class for each stored procedure, giving typesafe access to parameter values and output. DAL calls then looks like instantiate wrapper-populate parameters-execute call:       using (var sp = new uspGetManagerEmployees())     {         sp.ManagerID = 16;         using (var reader = sp.Execute())         {             //map entities from the output         }     }   Or rolling it all into a fluent DAL call – which is nicer to read and implicitly disposes the resources:   This is fine, the wrapper classes are very simple to handwrite or generate. But as the codebase grows, you end up with a proliferation of very small wrapper classes: The wrappers don't add much other than encapsulating the stored procedure call and giving you typesafety for the parameters. With the dynamic extension in .NET 4.0 you have the option to build a single wrapper class, and get rid of the one-to-one stored procedure to wrapper class mapping. In the dynamic version, the call looks like this:       dynamic getUser = new DynamicSqlStoredProcedure("uspGetManagerEmployees", Database.AdventureWorks);     getUser.ManagerID = 16;       var employees = Fluently.Load<List<Employee>>()                             .With<EmployeeMap>()                             .From(getUser);   The important difference is that the ManagerId property doesn't exist in the DynamicSqlStoredProcedure class. Declaring the getUser object with the dynamic keyword allows you to dynamically add properties, and the DynamicSqlStoredProcedure class intercepts when properties are added and builds them as stored procedure parameters. When getUser.ManagerId = 16 is executed, the base class adds a parameter call (using the convention that parameter name is the property name prefixed by "@"), specifying the correct SQL Server data type (mapping it from the type of the value the property is set to), and setting the parameter value. Code Sample This is worked through in a sample project on github – Dynamic Stored Procedure Sample – which also includes a static version of the wrapper for comparison. (I'll upload this to the MSDN Code Gallery once my account has been resurrected). Points worth noting are: DynamicSP.Data – database-independent DAL that has all the data plumbing code. DynamicSP.Data.SqlServer – SQL Server DAL, thin layer on top of the generic DAL which adds SQL Server specific classes. Includes the DynamicSqlStoredProcedure base class. DynamicSqlStoredProcedure.TrySetMember. Invoked when a dynamic member is added. Assumes the property is a parameter named after the SP parameter name and infers the SqlDbType from the framework type. Adds a parameter to the internal stored procedure wrapper and sets its value. uspGetManagerEmployees – the static version of the wrapper. uspGetManagerEmployeesTest – test fixture which shows usage of the static and dynamic stored procedure wrappers. The sample uses stored procedures from the AdventureWorks database in the SQL Server 2008 Sample Databases. Discussion For this scenario, the dynamic option is very favourable. Assuming your DAL is itself wrapped by a higher layer, the stored procedure wrapper classes have very little reuse. Even if you're codegening the classes and test fixtures, it's still additional effort for very little value. The main consideration with dynamic classes is that the compiler ignores all the members you use, and evaluation only happens at runtime. In this case where scope is strictly limited that's not an issue – but you're relying on automated tests rather than the compiler to find errors, but that should just encourage better test coverage. Also you can codegen the dynamic calls at a higher level. Performance may be a consideration, as there is a first-time-use overhead when the dynamic members of an object are bound. For a single run, the dynamic wrapper took 0.2 seconds longer than the static wrapper. The framework does a good job of caching the effort though, so for 1,000 calls the dynamc version still only takes 0.2 seconds longer than the static: You don't get IntelliSense on dynamic objects, even for the declared members of the base class, and if you've been using class names as keys for configuration settings, you'll lose that option if you move to dynamics. The approach may make code more difficult to read, as you can't navigate through dynamic members, but you do still get full debugging support.     var employees = Fluently.Load<List<Employee>>()                             .With<EmployeeMap>()                             .From<uspGetManagerEmployees>                             (                                 i => i.ManagerID = 16,                                 x => x.Execute()                             );

    Read the article

  • Pre-filtering and shaping OData feeds using WCF Data Services and the Entity Framework - Part 2

    - by rajbk
    In the previous post, you saw how to create an OData feed and pre-filter the data. In this post, we will see how to shape the data. A sample project is attached at the bottom of this post. Pre-filtering and shaping OData feeds using WCF Data Services and the Entity Framework - Part 1 Shaping the feed The Product feed we created earlier returns too much information about our products. Let’s change this so that only the following properties are returned – ProductID, ProductName, QuantityPerUnit, UnitPrice, UnitsInStock. We also want to return only Products that are not discontinued.  Splitting the Entity To shape our data according to the requirements above, we are going to split our Product Entity into two and expose one through the feed. The exposed entity will contain only the properties listed above. We will use the other Entity in our Query Interceptor to pre-filter the data so that discontinued products are not returned. Go to the design surface for the Entity Model and make a copy of the Product entity. A “Product1” Entity gets created.   Rename Product1 to ProductDetail. Right click on the Product entity and select “Add Association” Make a one to one association between Product and ProductDetails.   Keep only the properties we wish to expose on the Product entity and delete all other properties on it (see diagram below). You delete a property on an Entity by right clicking on the property and selecting “delete”. Keep the ProductID on the ProductDetail. Delete any other property on the ProductDetail entity that is already present in the Product entity. Your design surface should look like below:    Mapping Entity to Database Tables Right click on “ProductDetail” and go to “Table Mapping”   Add a mapping to the “Products” table in the Mapping Details.   After mapping ProductDetail, you should see the following.   Add a referential constraint. Lets add a referential constraint which is similar to a referential integrity constraint in SQL. Double click on the Association between the Entities and add the constraint with “Principal” set to “Product”. Let us review what we did so far. We made a copy of the Product entity and called it ProductDetail We created a one to one association between these entities Excluding the ProductID, we made sure properties were not duplicated between these entities  We added a ProductDetail entity to Products table mapping (Entity to Database). We added a referential constraint between the entities. Lets build our project. We get the following error: ”'NortwindODataFeed.Product' does not contain a definition for 'Discontinued' and no extension method 'Discontinued' accepting a first argument of type 'NortwindODataFeed.Product' could be found …" The reason for this error is because our Product Entity no longer has a “Discontinued” property. We “moved” it to the ProductDetail entity since we want our Product Entity to contain only properties that will be exposed by our feed. Since we have a one to one association between the entities, we can easily rewrite our Query Interceptor like so: [QueryInterceptor("Products")] public Expression<Func<Product, bool>> OnReadProducts() { return o => o.ProductDetail.Discontinued == false; } Similarly, all “hidden” properties of the Product table are available to us internally (through the ProductDetail Entity) for any additional logic we wish to implement. Compile the project and view the feed. We see that the feed returns only the properties that were part of the requirement.   To see the data in JSON format, you have to create a request with the following request header Accept: application/json, text/javascript, */* (easy to do in jQuery) The result should look like this: { "d" : { "results": [ { "__metadata": { "uri": "http://localhost.:2576/DataService.svc/Products(1)", "type": "NorthwindModel.Product" }, "ProductID": 1, "ProductName": "Chai", "QuantityPerUnit": "10 boxes x 20 bags", "UnitPrice": "18.0000", "UnitsInStock": 39 }, { "__metadata": { "uri": "http://localhost.:2576/DataService.svc/Products(2)", "type": "NorthwindModel.Product" }, "ProductID": 2, "ProductName": "Chang", "QuantityPerUnit": "24 - 12 oz bottles", "UnitPrice": "19.0000", "UnitsInStock": 17 }, { ... ... If anyone has the $format operation working, please post a comment. It was not working for me at the time of writing this.  We have successfully pre-filtered our data to expose only products that have not been discontinued and shaped our data so that only certain properties of the Entity are exposed. Note that there are several other ways you could implement this like creating a QueryView, Stored Procedure or DefiningQuery. You have seen how easy it is to create an OData feed, shape the data and pre-filter it by hardly writing any code of your own. For more details on OData, Google it with your favorite search engine :-) Also check out the one of the most passionate persons I have ever met, Pablo Castro – the Architect of Aristoria WCF Data Services. Watch his MIX 2010 presentation titled “OData: There's a Feed for That” here. Download Sample Project for VS 2010 RTM NortwindODataFeed.zip

    Read the article

  • Cant correctly install Lazarus

    - by user206316
    I have a little problem with installing and running Lazarus. I just upgrade ubuntu from 13.04 to 13.10. When i had 13.04, i could install lazarus without any problems, but in 13.10 lazarus magicaly dissapeared, and when i tried install it from ubuntu software center, it said something like in my software resources lazarus-ide-0.9.30.4 doesnt exist. After some research on net i tried delete all files from earlier installations, download deb packages from sourceforge and install them, but when i want to instal fpc-src, error shows up with output: (Reading database ... 100% (Reading database ... 239063 files and directories currently installed.) Unpacking fpc-src (from .../Stiahnut/Lazarus/fpc-src.deb) ... dpkg: error processing /home/richi/Stiahnut/Lazarus/fpc-src.deb (--install): trying to overwrite '/usr/share/fpcsrc/2.6.2/rtl/nativent/tthread.inc', which is also in package fpc-source-2.6.2 2.6.2-5 dpkg-deb (subprocess): decompressing archive member: internal gzip write error: Broken pipe dpkg-deb: error: subprocess <decompress> returned error exit status 2 dpkg-deb (subprocess): cannot copy archive member from '/home/richi/Stiahnut/Lazarus/fpc-src.deb' to decompressor pipe: failed to write (Broken pipe) when i started lazarus, it of course tell me that it cant find fpc compier and fpc sources. So, please, i really need program for school and i dont wanna reinstall os anymore or something like that :( (Ubuntu 13.10 64bit) P.S: im not skilled in linux so if u know some commands to fix it just write them for copy and paste :) P.P.S:Sorry for bad English, im Slovak xD P.P.P.S: Thank so much for any answers update: output from sudo dpkg -l | grep "^rc" richi@Richi-Ubuntu:~/lazarus1.0.12$ sudo dpkg -l | grep "^rc" rc account-plugin-generic-oauth 0.10bzr13.03.26-0ubuntu1.1 amd64 GNOME Control Center account plugin for single signon - generic OAuth rc appmenu-gtk:amd64 12.10.3daily13.04.03-0ubuntu1 amd64 Export GTK menus over DBus rc appmenu-gtk3:amd64 12.10.3daily13.04.03-0ubuntu1 amd64 Export GTK menus over DBus rc fp-compiler-2.6.0 2.6.0-9 amd64 Free Pascal - compiler rc fp-utils-2.6.0 2.6.0-9 amd64 Free Pascal - utilities rc lazarus-ide-0.9.30.4 0.9.30.4-4 amd64 IDE for Free Pascal - common IDE files rc lazarus-ide-1.0.10 1.0.10+dfsg-1 amd64 IDE for Free Pascal - common IDE files rc lcl-utils-0.9.30.4 0.9.30.4-4 amd64 Lazarus Components Library - command line build tools rc lcl-utils-1.0.10 1.0.10+dfsg-1 amd64 Lazarus Components Library - command line build tools rc libbamf3-1:amd64 0.4.0daily13.06.19~13.04-0ubuntu1 amd64 Window matching library - shared library rc libboost-filesystem1.49.0 1.49.0-4 amd64 filesystem operations (portable paths, iteration over directories, etc) in C++ rc libboost-signals1.49.0 1.49.0-4 amd64 managed signals and slots library for C++ rc libboost-system1.49.0 1.49.0-4 amd64 Operating system (e.g. diagnostics support) library rc libboost-thread1.49.0 1.49.0-4 amd64 portable C++ multi-threading rc libbrlapi0.5:amd64 4.4-8ubuntu4 amd64 braille display access via BRLTTY - shared library rc libcamel-1.2-40 3.6.4-0ubuntu1.1 amd64 Evolution MIME message handling library rc libcolumbus0-0 0.4.0daily13.04.16~13.04-0ubuntu1 amd64 error tolerant matching engine - shared library rc libdns95 1:9.9.2.dfsg.P1-2ubuntu2.1 amd64 DNS Shared Library used by BIND rc libdvbpsi7 0.2.2-1 amd64 library for MPEG TS and DVB PSI tables decoding and generating rc libebackend-1.2-5 3.6.4-0ubuntu1.1 amd64 Utility library for evolution data servers rc libedata-book-1.2-15 3.6.4-0ubuntu1.1 amd64 Backend library for evolution address books rc libedata-cal-1.2-18 3.6.4-0ubuntu1.1 amd64 Backend library for evolution calendars rc libgc1c3:amd64 1:7.2d-0ubuntu5 amd64 conservative garbage collector for C and C++ rc libgd2-xpm:amd64 2.0.36~rc1~dfsg-6.1ubuntu1 amd64 GD Graphics Library version 2 rc libgd2-xpm:i386 2.0.36~rc1~dfsg-6.1ubuntu1 i386 GD Graphics Library version 2 rc libgnome-desktop-3-4 3.6.3-0ubuntu1 amd64 Utility library for loading .desktop files - runtime files rc libgphoto2-2:amd64 2.4.14-2 amd64 gphoto2 digital camera library rc libgphoto2-2:i386 2.4.14-2 i386 gphoto2 digital camera library rc libgphoto2-port0:amd64 2.4.14-2 amd64 gphoto2 digital camera port library rc libgphoto2-port0:i386 2.4.14-2 i386 gphoto2 digital camera port library rc libgtksourceview-3.0-0:amd64 3.6.3-0ubuntu1 amd64 shared libraries for the GTK+ syntax highlighting widget rc libgweather-3-1 3.6.2-0ubuntu1 amd64 GWeather shared library rc libharfbuzz0:amd64 0.9.13-1 amd64 OpenType text shaping engine rc libibus-1.0-0:amd64 1.4.2-0ubuntu2 amd64 Intelligent Input Bus - shared library rc libical0 0.48-2 amd64 iCalendar library implementation in C (runtime) rc libimobiledevice3 1.1.4-1ubuntu6.2 amd64 Library for communicating with the iPhone and iPod Touch rc libisc92 1:9.9.2.dfsg.P1-2ubuntu2.1 amd64 ISC Shared Library used by BIND rc libkms1:amd64 2.4.46-1 amd64 Userspace interface to kernel DRM buffer management rc libllvm3.2:i386 1:3.2repack-7ubuntu1 i386 Low-Level Virtual Machine (LLVM), runtime library rc libmikmod2:amd64 3.1.12-5 amd64 Portable sound library rc libpackagekit-glib2-14:amd64 0.7.6-3ubuntu1 amd64 Library for accessing PackageKit using GLib rc libpoppler28:amd64 0.20.5-1ubuntu3 amd64 PDF rendering library rc libraw5:amd64 0.14.7-0ubuntu1.13.04.2 amd64 raw image decoder library rc librhythmbox-core6 2.98-0ubuntu5 amd64 support library for the rhythmbox music player rc libsdl-mixer1.2:amd64 1.2.12-7ubuntu1 amd64 Mixer library for Simple DirectMedia Layer 1.2, libraries rc libsnmp15 5.4.3~dfsg-2.7ubuntu1 amd64 SNMP (Simple Network Management Protocol) library rc libsyncdaemon-1.0-1 4.2.0-0ubuntu1 amd64 Ubuntu One synchronization daemon library rc libunity-core-6.0-5 7.0.0daily13.06.19~13.04-0ubuntu1 amd64 Core library for the Unity interface. rc libusb-0.1-4:i386 2:0.1.12-23.2ubuntu1 i386 userspace USB programming library rc libwayland0:amd64 1.0.5-0ubuntu1 amd64 wayland compositor infrastructure - shared libraries rc linux-image-3.8.0-19-generic 3.8.0-19.30 amd64 Linux kernel image for version 3.8.0 on 64 bit x86 SMP rc linux-image-3.8.0-31-generic 3.8.0-31.46 amd64 Linux kernel image for version 3.8.0 on 64 bit x86 SMP rc linux-image-extra-3.8.0-19-generic 3.8.0-19.30 amd64 Linux kernel image for version 3.8.0 on 64 bit x86 SMP rc linux-image-extra-3.8.0-31-generic 3.8.0-31.46 amd64 Linux kernel image for version 3.8.0 on 64 bit x86 SMP rc screen-resolution-extra 0.15ubuntu1 all Extension for the GNOME screen resolution applet rc unity-common 7.0.0daily13.06.19~13.04-0ubuntu1 all Common files for the Unity interface.

    Read the article

  • CodePlex Daily Summary for Sunday, March 07, 2010

    CodePlex Daily Summary for Sunday, March 07, 2010New ProjectsAlgorithminator: Universal .NET algorithm visualizer, which helps you to illustrate any algorithm, written in any .NET language. Still in development.ALToolkit: Contains a set of handy .NET components/classes. Currently it contains: * A Numeric Text Box (an Extended NumericUpDown) * A Splash Screen base fo...Automaton Home: Automaton is a home automation software built with a n-Tier, MVVM pattern utilzing WCF, EF, WPF, Silverlight and XBAP.Developer Controls: Developer Controls contains various controls to help build applications that can script/write code.Dynamic Reference Manager: Dynamic Reference Manager is a set (more like a small group) of classes and attributes written in C# that allows any .NET program to reference othe...indiologic: Utilities of an IndioNeural Cryptography in F#: This project is my magistracy resulting work. It is intended to be an example of using neural networks in cryptography. Hashing functions are chose...Particle Filter Visualization: Particle Filter Visualization Program for the Intel Science and Engineering FairPólya: Efficient, immutable, polymorphic collections. .Net lacks them, we provide them*. * By we, we mean I; and by efficient, I mean hopefully so.project euler solutions from mhinze: mhinze project euler solutionsSilverlight 4 and WCF multi layer: Silverlight 4 and WCF multi layersqwarea: Project for a browser-based, minimalistic, massively multiplayer strategy game. Part of the "Génie logiciel et Cloud Computing" course of the ENS (...SuperSocket: SuperSocket, a socket application framework can build FTP/SMTP/POP server easilyToast (for ASP.NET MVC): Dynamic, developer & designer friendly content injection, compression and optimization for ASP.NET MVCNew ReleasesALToolkit: ALToolkit 1.0: Binary release of the libraries containing: NumericTextBox SplashScreen Based on the VB.NET code, but that doesn't really matter.Blacklist of Providers: 1.0-Milestone 1: Blacklist of Providers.Milestone 1In this development release implemented - Main interface (Work Item #5453) - Database (Work Item #5523)C# Linear Hash Table: Linear Hash Table b2: Now includes a default constructor, and will throw an exception if capacity is not set to a power of 2 or loadToMaintain is below 1.Composure: CassiniDev-Trunk-40745-VS2010.rc1.NET4: A simple port of the CassiniDev portable web server project for Visual Studio 2010 RC1 built against .NET 4.0. The WCF tests currently fail unless...Developer Controls: DevControls: These are the version 1.0 releases of these controls. Download the individually or all together (in a .zip file). More releases coming soon!Dynamic Reference Manager: DRM Alpha1: This is the first release. I'm calling it Alpha because I intend implementing other functions, but I do not intend changing the way current functio...ESB Toolkit Extensions: Tellago SOA ESB Extenstions v0.3: Windows Installer file that installs Library on a BizTalk ESB 2.0 system. This Install automatically configures the esb.config to use the new compo...GKO Libraries: GKO Libraries 0.1 Alpha: 0.1 AlphaHome Access Plus+: v3.0.3.0: Version 3.0.3.0 Release Change Log: Added Announcement Box Removed script files that aren't needed Fixed & issue in directory path Stylesheet...Icarus Scene Engine: Icarus Scene Engine 1.10.306.840: Icarus Professional, Icarus Player, the supporting software for Icarus Scene Engine, with some included samples, and the start of a tutorial (with ...mavjuz WndLpt: wndlpt-0.2.5: New: Response to 5 LPT inputs "test i 1" New: Reaction to 12 LPT outputs "test q 8" New: Reaction to all LPT pins "test pin 15" New: Syntax: ...Neural Cryptography in F#: Neural Cryptography 0.0.1: The most simple version of this project. It has a neural network that works just like logical AND and a possibility to recreate neural network from...Password Provider: 1.0.3: This release fixes a bug which caused the program to crash when double clicking on a generic item.RoTwee: RoTwee 6.2.0.0: New feature is as next. 16649 Add hashtag for tweet of tune.Now you can tweet your playing tune with hashtag.Visual Studio DSite: Picture Viewer (Visual C++ 2008): This example source code allows you to view any picture you want in the click of a button. All you got to do is click the button and browser via th...WatchersNET CKEditor™ Provider for DotNetNuke: CKEditor Provider 1.8.00: Whats New File Browser: Folders & Files View reworked File Browser: Folders & Files View reworked File Browser: Folders are displayed as TreeVi...WSDLGenerator: WSDLGenerator 0.0.0.4: - replaced CommonLibrary.dll by CommandLineParser.dll - added better support for custom complex typesMost Popular ProjectsMetaSharpSilverlight ToolkitASP.NET Ajax LibraryAll-In-One Code FrameworkWindows 7 USB/DVD Download Toolニコ生アラートWindows Double ExplorerVirtual Router - Wifi Hot Spot for Windows 7 / 2008 R2Caliburn: An Application Framework for WPF and SilverlightArkSwitchMost Active ProjectsUmbraco CMSRawrSDS: Scientific DataSet library and toolsBlogEngine.NETjQuery Library for SharePoint Web Servicespatterns & practices – Enterprise LibraryIonics Isapi Rewrite FilterFarseer Physics EngineFasterflect - A Fast and Simple Reflection APIFluent Assertions

    Read the article

< Previous Page | 430 431 432 433 434 435 436 437 438 439 440 441  | Next Page >