Search Results

Search found 11524 results on 461 pages for 'pc wiki'.

Page 436/461 | < Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >

• How to transition to Comcast with static IP address [migrated]

  - by steveha

  I have my own email server in my house, on a static IP address. I have had business DSL for over a decade, but I also now have Comcast business Internet. I want to transition from the DSL to the Comcast, and I have some questions. I have a domain name, my own mail server, and a firewall (a PC with two network interfaces, running Devil-Linux). I need to make sure I understand how to set up the Comcast cable box, and how to set up my firewall. First, do I need to change any settings in the cable box? Currently I have only used the cable box by plugging in a laptop, with the laptop doing DHCP. I think I can leave the box alone but I would like to make sure. Second, I'm not sure I understand the instructions Comcast gave me for setting up the firewall. My DSL provider gave me the following information: static IP address, net mask, gateway, and two DNS servers. Comcast gave me: static IP address, routable static IP address, net mask, and two DNS servers, and told me to put the "static IP address" as the "gateway" on the firewall. Is this just Comcast-speak here? Does "routable static IP address" mean the same thing as "static IP address" in my DSL setup, the end-point address that I should publish in the DNS MX records for my email server? Or should I publish the "static IP address", and Comcast will then route all its traffic over the cable box? My plan is: first, I'm going to configure another firewall, so I have one firewall for the DSL and one for the Comcast (rather than madly editing settings to switch back and forth). Then I will publish the new Comcast static IP address as a backup email server address in the DNS MX records, wait a while to let it propagate, and then switch my home over from the DSL to the Comcast. Then I'll change DNS to make that the primary mail address and the DSL the secondary, let that go a while and make sure it seems reliable. Then I'll remove the DSL from the DNS MX records completely, and finally shut down the DSL service. (I thought about keeping the DSL as a backup, but the reason I'm leaving DSL is that it has become unreliable; and I have heard that Comcast business Internet is reliable.) Final question, any advice for me? Anything you think might be useful, helpful, or educational. Thanks.

  Read the article

• What is a good layout for a somewhat advanced home network and storage solution?

  - by Shaun

  My home network/storage needs are changing and I am searching for some opinions and starting points on what a good network/storage layout would be that can serve my needs for a few years into the future. I think I have a decent starting point for equipment, but I am also willing to invest fairly heavily in a solution that can last me for a while. I am a bit of a tech nerd and I have a moderate tolerance for setup of the solution. I would prefer if maintenance of the system is somewhat low once it is setup, but I am willing to accept some tradeoffs. Existing equipment: Router - Netgear WNDR3700 (gigabit) Router - DLink Gamerlounge DGL-4300 (gigabit) Switch - 16 port Trendnet green switch (gigabit) Switch - 5 port Trendnet green (gigabit) Computer - i7-950 office computer (gigabit ethernet) Computer - Q6600 quad core media center, hooked up to TV, records shows (gigabit ethernet) Computer - Acer 1810T ultraportable laptop (gigabit and N ethernet) NAS - Intel SS4200-E (gigabit) External hard drive - 2TB WD Green drive (esata) All kinds of miscellaneous network connected TV, Bluray, Verizon network extender, HDhomerun TV tuners, etc. Requirements: -Robust backup solution for a growing collection of huge family picture files and personal files, around 1.5TB. (Including offsite backup) -Central location for all user's files, while also keeping them secure from each other. -Storage for terabytes of movie backups and recorded TV, and access to them from all computers (maybe around 4TB eventually) -Possibility to host files to friends and family easily Nice to have: -Backup of terabytes of movie backups Intriguing possibilities: -Capability to have users' Windows desktops and files look the same from all network computers I am not sure if the new Windows Home Server 2011 would fit into this well, if I need a domain server, how best to organize my backups, or how to most effectively use RAID. Currently I am simply backing up all computers to a RAID 1 on the NAS box, which I was thinking could prevent a situation where I reach for a backup and find that the disk is corrupt. One possibility that I am thinking about now is simply using my media center PC with a huge RAID of hard drives on which all files are stored. Pseudo-backup of all files would be present because of the RAID, but important files would also be backed up off site via carrying hard drives to work. But what if corruption seeps into the files and the corrupted data is then backed up? Does RAID protect against this? I really want to take next to zero risks with the irreplaceable files. I can handle some degree of risk with the movies and other files. I'm looking for critiques on this idea as well as other possibilities. To summarize, my goal is high functionality, media capable, and robust backup of irreplaceable files.

  Read the article

• Cannot run a VM with more than three network interfaces with KVM

  - by Bostonvaulter

  I'm running KVM on top of Ubuntu 10.10 Server I can create VM's (Virtual Machine) and network interfaces fine but I cannot seem to add more than three network interfaces. As soon as I have a VM with four network interfaces it gets stuck on startup at the starting SeaBIOS page with this message: Starting SeaBIOS (version pre-0.6.1-20100702_143500-palmer) So far I've verified this with two VM's, a Ubuntu 10.10 desktop and a Vyatta router. The specific network hardware I assign to the VM's doesn't seem to matter. I'm trying to have one bridged interface and three private networks using Vyatta to route between them. Does anyone know why I can't run a VM with more than three network interfaces? Edit: Additionally the KVM thread responsible for the specific VM hangs using ~100% CPU (i.e. one core). Here's the command for the process that is hanging: /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1,sockets=1,cores=1,threads=1 -name vyatta -uuid 6dff7c94-6810-423e-5fea-fec10da0e9b7 -nodefaults -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/vyatta.monitor,server,nowait -mon chardev=monitor,mode=readline -rtc base=utc -boot c -drive file=/home/rams/virtual-machines/vyatta.img,if=none,id=drive-ide0-0-0,boot=on,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -device rtl8139,vlan=0,id=net0,mac=00:54:00:be:cc:4b,bus=pci.0,addr=0x3 -net tap,fd=97,vlan=0,name=hostnet0 -device rtl8139,vlan=1,id=net1,mac=52:54:00:da:59:ed,bus=pci.0,addr=0x5 -net tap,fd=98,vlan=1,name=hostnet1 -device rtl8139,vlan=2,id=net2,mac=52:54:00:ce:22:b6,bus=pci.0,addr=0x6 -net tap,fd=99,vlan=2,name=hostnet2 -device rtl8139,vlan=3,id=net3,mac=52:54:00:1e:bc:46,bus=pci.0,addr=0x7 -net tap,fd=101,vlan=3,name=hostnet3 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -vnc 127.0.0.1:0 -k en-us -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 Edit: I've also found an error in dmesg that might be related (it also shows up when running virtd in verbose mode): 14:47:24.399: warning : qemudParsePCIDeviceStrs:1422 : Unexpected exit status '1', qemu probably failed I've also tried disabling app armor but that doesn't seem to make a difference.

  Read the article

• Need help making an ODBC MySQL Connection

  - by Andy Moore

  Short Version: How do I connect from PowerShell to an ODBC 5.1 MySQL Driver? I can't seem to find any connection strings that accurately have a "Provider" field for this particular instance. (See bottom of this question for examples/errors) ===== Long Version: I'm not a server guy, and I've been handed the task of setting up PowerGadgets on our network. I have a MySQL server running on a Linux box, that is configured for remote access and has a user defined for remote access as well. On my windows desktop PC, I have PowerGadgets installed. I installed the MySQL ODBC 5.1 connector, and went to Control Panel Data Sources and set up a User DSN connection to the database. The connection, user, and pass seem to be correct because it lists the tables of the database in my windows control panel. Where I'm running into trouble is in 3 places in PowerGadgets: When selecting a data source, I can select "SQL Server". Inputting the servers IP address does not work and I can't get this option to work at all. When selecting a data source, I can select "OleDB". This screen has a wizard on it, that appears to populate all the correct information (including database table names!) for me. "Test Connection" runs great. But if I try to complete the wizard, I get the error "The .NET Framework data provider for OLEDB does not support the MS Ole DB provider for ODBC Drivers." When selecting a data source, I can select "ODBC". This screen does not have a wizard and I cannot figure out a "connection string" that works. Typically it will respond with the error "The field 'Provider' is missing". Googling ODBC connection strings doesn't reveal any examples with a "provider" field and have no idea what to put in here. The connection string (for #2) above contains "SQLOLEDB" as a provider, and upon inputting that value into this connection string I get the same connection error that #2 gets. I believe I can solve my problems by figuring out a connection string for #3 but don't know where to get started. (PowerGadgets also allows for PowerShell support but I believe I will run into the same problem there) == Here's my current PowerShell connection that doesn't work: invoke-sql -connection "Driver={MySQL ODBC 5.1 Driver};Initial Catalog=hq_live;Data Source=HQDB" -sql "Select * FROM accounts" Spits back the error: "Invoke-Sql : An OLE DB Provider was not specified in the ConnectionString. An example would be, 'Provider=SQLOLEDB;'. == Another string that doesn't work: invoke-sql -connection "Provider=MSDASQL.1;Persist Security Info=False;Data Source=HQDB;Initial Catalog=hq_live" -sql "select * from accounts" And the error: The .Net Framework Data Provider for OLEDB (System.Data.OleDb) does not support the Microsoft OLE DB Provider for ODBC Drivers (MSDASQL). Use the .Net Framework Data Provider for ODBC (System.Data.Odbc).

  Read the article

• chkdsk, SeaTools, and "does not have enough space to replace bad clusters"

  - by Zian Choy

  When I tried to do a Windows Vista Complete PC Backup, I received an error message that blathered about bad sectors. Then, when I ran chkdsk /r on the destination drive, this is what I got: C:\Windows\system32>chkdsk /R E: The type of the file system is NTFS. Volume label is Desktop Backup. CHKDSK is verifying files (stage 1 of 5)... 822016 file records processed. File verification completed. 1 large file records processed. 0 bad file records processed. 0 EA records processed. 0 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 848938 index entries processed. Index verification completed. 0 unindexed files processed. CHKDSK is verifying security descriptors (stage 3 of 5)... 822016 security descriptors processed. Security descriptor verification completed. 13461 data files processed. CHKDSK is verifying file data (stage 4 of 5)... The disk does not have enough space to replace bad clusters detected in file 239649 of name . The disk does not have enough space to replace bad clusters detected in file 239650 of name . The disk does not have enough space to replace bad clusters detected in file 239651 of name . An unspecified error occurred.f 822000 files processed) Yet, when I ran the SeaTools short & long generic tests on the Seagate disk, I didn't receive any errors. I know that I could reformat the disk and try running chkdsk /r again but I'd prefer to avoid waiting 4 hours in the hope that the problem was magically fixed. On the other hand, if I RmA the drive to Seagate, I have no SeaTools error number to use and they may claim that the drive is just fine. What should I try to do next? Side frustration: There is plenty of free hard drive space. The E: partition has 182 GB free.

  Read the article

• libvirt qemu/kvm migration problem

  - by Panda

  I am using kvm and libvirt on my Dell server. Now i am trying to migrate one virtual machine from a physical server to another. However, I failed everytime. In virsh on physicalServer1, I typed: virsh # migrate virtualmachine1 qemu+ssh://username@physicalServer2/system error: operation failed: migration to 'tcp:physicalServer2:49163' failed: migration failed Then I searched FAQ part on libvirt.org. It says: error: operation failed: migration to '...' failed: migration failed This is an error often encountered when trying to migrate with QEMU/KVM. This typically happens with plain migration, when the source VM cannot connect to the destination host. You will want to make sure your hosts are properly configured for migration (see the migration section of this FAQ) I managed to ssh physicalServer2 from a shell on virtualmachine1 so the above red part did not explain my failure. I also open ports on physicalServer2, iptables -L shows following information: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT tcp -- anywhere anywhere state NEW tcp dpts:49152:49215 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer2: 2011-05-06 13:37:30.708: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.14 -enable-kvm -m 2048 -smp 1,sockets=1,cores=1,threads=1 -name openjudge-test -uuid a8c704bc-a4f9-90db-3e57-40e60b00aac1 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/virtualmachine1.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=readline -rtc base=utc -boot c -drive file=/media/nfs/virtualmachine1.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=00:16:36:8a:22 :a0,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:2 -vga cirrus -incoming tcp:0.0.0.0:49163 -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/0 2011-05-06 13:37:30.915: shutting down The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer1 is empty. Both physical servers are using Ubuntu 11.04. The libvirt and kvm used are installed by apt-get. The libvirt version is 0.8.8.

  Read the article

• Low framerate on background apps

  - by user1698923

  My problem is that when a game is running in the foreground, in Full Screen mode, any applications on my second monitor (such as youtube videos, videos, not app specific) drop their frame-rate to about 2-3 FPS. It seems like some sort of power management option that I can't track down. As far as I can tell, it's not due to the GPU not being able to keep up. For instance, my PC can play League of Legends at about 280FPS when the framerate is uncapped. If i cap it at 60FPS using the in-game option, it has no affect on the performance of the background app. Summary Operating System Windows 8 Pro 64-bit CPU Intel Core i7 3820 @ 3.60GHz 42 °C Sandy Bridge-E 32nm Technology RAM 12.0GB Triple-Channel DDR3 @ 533MHz (7-7-7-20) Motherboard Gigabyte Technology Co., Ltd. X79-UD3 (SOCKET 0) 37 °C Graphics DELL U2713HM (2560x1440@59Hz) DELL U2713HM (2560x1440@59Hz) 1280MB NVIDIA GeForce GTX 570 (Gigabyte) 58 °C Hard Drives 212GB Volume0 (RAID) 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 36 °C 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 34 °C Optical Drives No optical disk drives detected Audio ASUS Xonar Essence STX Audio Device Operating System Windows 8 Pro 64-bit Computer type: Desktop Graphics Monitor 1 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Secondary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY4\Monitor0 Monitor 2 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Primary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY5\Monitor0 NVIDIA GeForce GTX 570 Manufacturer NVIDIA Model GeForce GTX 570 GPU GF110 Device ID 10DE-1086 Revision A2 Subvendor Gigabyte (1458) Series GeForce GTX 500 Current Performance Level Level 3 Current GPU Clock 845 MHz Current Memory Clock 1900 MHz Current Shader Clock 1690 MHz Voltage 0.988 V Technology 40 nm Die Size 520 mm² Release Date Dec 07, 2010 DirectX Support 11.0 OpenGL Support 5.0 Bus Interface PCI Express x16 Temperature 57 °C Driver version 9.18.13.2018 BIOS Version 70.10.55.00.01 ROPs 40 Shaders 512 unified Memory Type GDDR5 Memory 1280 MB Bus Width 64x5 (320 bit) Filtering Modes 16x Anisotropic Noise Level Moderate Max Power Draw 219 Watts Count of performance levels : 3 Level 1 - "Default" GPU Clock 50 MHz Memory Clock 135 MHz Shader Clock 101 MHz Level 2 - "2D Desktop" GPU Clock 405 MHz Memory Clock 324 MHz Shader Clock 810 MHz Level 3 - "3D Applications" GPU Clock 845 MHz Memory Clock 1900 MHz Shader Clock 1690 MHz Things I've tried: 1) Updating the graphics driver 2) Setting windows power mode to High Performance 3) Reset Nvidia Global Performance settings to default

  Read the article

• How can I connect DLNA devices through NAT?

  - by Bob

  I have a Windows 7 PC running Serviio as a DLNA server. I have a Samsung I9100G running Skifta as a DLNA renderer (client). My network topology: At the moment, I can connect and watch my videos fine if the phone is on router #2. The server is on a wired network with #2. Router #1 is 192.168.1.1, router #2 is 192.168.2.1 (192.168.1.2) and router #3 is 192.168.3.1 (192.168.1.3). In other words, each router has its own subnet, using NAT - their "modem" port is connected with a "LAN" port on the modem/router 1. What I want to do is be able to connect to the DLNA server if the renderer is connected to router #1/#3 - #1 is on the WAN side of #2, while #3 is even further separated. I'll settle for just #1 working, though. Normally, I would just forward the appropriate ports, and everything would work fine. However, (apparently) DLNA uses UPnP, which I am unfamiliar with. I tried enabling UPnP on router #2, but that did not seem not change anything. It's a Belkin F5D7230-4 6000 - there's reported issues with UPnP on F5D7230-4 7000. UPnP is already enabled on router #1 - a Billion BiPAC 7700N. I've also tried the built in DLNA renderer/server/controller on my phone, Samsung AllShare. It can see the server on router #2 and browse files, but has issues playing or downloading them. It also can't see the server on the other two networks. I'm currently using Skifta/s "local" mode. "Remote" mode requires an account, which I don't really want to create if not necessary. Is it possible too do what I'm trying to do? If no, are there workarounds? If yes, how do I do it? Is my server the issue? The renderer (client)? The router(s)? My method? I can change just about anything except the routers.

  Read the article

• OCZ Vertex 2 not recognized by Ubuntu installer

  - by Zsub

  As I boot into the Ubuntu 10.10 (or 11.04, doesn't matter) live environment or installer, it just refuses to recognise my Vertex 2. It reports the disk as ATA and not supporting smart, shows no serial number, and doesn't list the size correctly. All fdisk tells me is Unable to read /dev/sda (it's the only storage in the PC). I'm now running a temporary install of Windows 7 off of it, which worked like a charm, so where am I going wrong with Ubuntu... Specs: Asus M4N68T-M LE V2 (BIOS 0702, most recent) OCZ Vertex 2 SSD 60 GB Amd Athlon II X4 640 Patriot PSD34G13332 4GB DDR3 ram (two banks) EDIT I installed a second drive, installed Ubuntu on that and booted, it recognised the SSD just fine. I'm now trying to apt-get upgrade the live-environment. I wonder if there is any way to sort of install Ubuntu from Ubuntu (I boot into the working install on the other drive, install it on the SSD and then boot from the SSD). EDIT2 Ok, so that doesn't work. The install detects the SSD, however, it cannot format it. EDIT3 After a fresh boot I can read out SMART-data and even perform a read-benchmark, but if I try to format it, or do a write-bench, it'll crap out and after that it says SMART is not supported. So basically it seems I can't write to the disk, as it will stop working when I do, I will try to run repeated read-benchmarks to see if that has any effect. EDIT4 I'm running several read benchmarks on the drive right now, they give results that are to be expected from an SSD. If the read-benches don't fail, I can use fdisk on the disk, but it is now stuck trying to re-read the partition table after issueing the 'w' command. EDIT5 Parted Magic did recognize the drive and with hdparm -I even could tell me the drive was in a frozen state. I powercycled it (just pull out the plug from the SSD and plug it back in) and it wasn't frozen anymore. After that I could upgrade the firmware on the drive (still using Parted Magic) and format it to Ext4. After I rebooted into the Ubuntu installer, it wouldn't get recognized and hdparm didn't want to talk to it saying HDIO_DRIVE_CMD(identify) failed: Invalid exchange. EDIT6 For some reason if I enable one of the RAID controllers (the one the SSD is connected to, obviously) Ubuntu will let me format it, mount it and write to it. The installer also recognizes it. However if the raid controller is enabled but no array is defined the motherboard can't boot from it :(

  Read the article

• why can't I open a port on Win 7? is it the app's fault?

  - by rjnagle

  I am having problems opening a port from one Windows PC on my local network. On Windows 7 computer ("Computer A") I running Calibre, an ebook management program that has something called an "ebook content server" . In essence, it serves via the web a content catalog. From Computer A, I can access the content server on localhost. ie. http://127.0.0.1:8787 calls up the content server successfully. With ipconfig I have confirmed that its local IP address is 192.168.1.106 From Computer B (a Vista Machine) I can ping 192.168.1.106 I have tried opening/editing a port in the Windows Firewall several times. In Windows firewall -- Allowed Programs in Control Panel, I see a listing for Calibre (with both Home/Work and PUblic checked) In details, I see Name: Calibre, Port Number 8787, Protocol TCP If I use the Advanced Security configuration screen for the firewall, I created an Inbound Rule on Computer A for Calibre (with the settings I indicated). If I run this command line on Computer A, I see: netstat -a -n TCP 0.0.0.0:554 0.0.0.0:0 LISTENING TCP 0.0.0.0:664 0.0.0.0:0 LISTENING TCP 0.0.0.0:2869 0.0.0.0:0 LISTENING TCP 0.0.0.0:3306 0.0.0.0:0 LISTENING TCP 0.0.0.0:5357 0.0.0.0:0 LISTENING TCP 0.0.0.0:6570 0.0.0.0:0 LISTENING TCP 0.0.0.0:6580 0.0.0.0:0 LISTENING TCP 0.0.0.0:8787 0.0.0.0:0 LISTENING TCP 0.0.0.0:10243 0.0.0.0:0 LISTENING TCP 192.168.1.106:63020 74.125.227.51:80 TIME_WAIT TCP [::]:80 [::]:0 LISTENING TCP [::]:135 [::]:0 LISTENING TCP [::]:443 [::]:0 LISTENING TCP [::]:445 [::]:0 LISTENING TCP [::]:554 [::]:0 LISTENING TCP [::]:2869 [::]:0 LISTENING TCP [::]:5357 [::]:0 LISTENING TCP [::]:6570 [::]:0 LISTENING TCP [::]:6580 [::]:0 LISTENING TCP [::]:10243 [::]:0 LISTENING TCP [::]:49152 [::]:0 LISTENING TCP [::]:49153 [::]:0 LISTENING TCP [::]:49154 [::]:0 LISTENING TCP [::]:49155 [::]:0 LISTENING TCP [::]:49170 [::]:0 LISTENING And lots of other junk, but this seems relevant, I see port 80 is open (I run xampp apache web server for windows on Machine A) This is the only time I see port 8787 referenced from the netstat commmand. From Windows Computer B, I can, ping 192.168.1.106 and even view http://drupal.local (on Computer A) and http://192.168.1.106/ (which goes to the Xampp config screen on Computer A). But I cannot access via Computer B htttp://192.168.1.106:8787 or htttp://computerhosta:8787 So what is going wrong? Is this a problem with the Calibre application or have I incorrectly opened the port? What things could possibly interfere with the opening of this port? On a sidenote, I have tried using telnet from Computer B to see if port 80 or 8787 is open for 192.168.1.106. I get no reply for either one. Thanks.

  Read the article

• Issues getting a Cisco WLC 5508 to find AIR-LAP1142N

  - by user95917

  hoping someone can help me with a problem here. I'm attempting to setup a test (loan from Cisco) wireless network. Here's what i've got/done: 5508 Controller - Service Port IP set to 10.74.5.2 /24. Management IP set to 10.74.6.2 /24 with a default gateway of 10.74.6.1. Virtual IP set to 1.1.1.1. Copper SFP in slot 7, CAT5 (known good) going from there to port 1/0/47 on the switch. Green lights on both ends. 2960-S Switch - Vlan1 - 10.74.6.1 /24. dhcp pool 10.74.6.0 /24, default router 10.74.6.1. excluded-address 10.74.6.1, 10.74.6.2. 1/0/4 on the switch is set to switchport mode access and no shut. 1/0/47 on the switch is setup to switchport mode trunk and no shut. 1/0/4 has a CAT5 (known good) cable going from there to the AP. When I do a sh cdp nei from the switch, i can see the AP and Controller listed. When i configure my PC's nic to 10.74.5.5, and plug a cable from my nic to the SP port on the controller i can get on the device via the gui. In there, the only errors/info that show up in the trap are: Link Up: Slot: 0 Port: 7 Controller time base status - Controller is out of sync with the central timebase. I've manually set the time but apparently that's not quite the problem (or at least not the entire problem). When i plug the AP in, i see on the switch console that it grants it power, it sees it connect...but the controller won't see it for some reason. From what i've read you shouldn't have to do anything to the AP as it's managed by the controller...but i'm not sure what setting I'm missing for it to work. The AP light on top is continually cycling green, red, yellow. When I first start it up, it blinks green for 20 or so seconds, then goes to solid green for another 20 seconds or so, then flashes blue, green, red for awhile...but always ends up goinn back to the standard, green, red, yellow. Does anyone see any obvious issues with my setup or have any suggestions as to why i might be having a problem? Thanks for your help!

  Read the article

• Windows 7 playback of dvr-Microsoft files stutters

  - by Jim Lynn

  I've just had to install Windows 7 on my Media Center machine because my Vista installation had a faulty drive. I've got the latest drivers that I can find - Intel 945GM integrated Graphics, Realtek audio drivers. Things are working OK with one exception. Playback of old recordings, from dvr-Microsoft format files, is choppy. The picture freezes for a fraction of a second, then quickly catches up. The sound is uninterrupted and doesn't pause. These freezes happen once every 5 seconds or so. It's very regular. Playback of Live TV from the digital tuner is perfectly smooth. DVD playback is perfectly smooth. As an experiment, I used the MPEG editing package VideoReDo to create a small test file in three different formats. This program takes the raw MPEG streams and repackages them into the desired container. I took the same clip and created three files in three formats: dvr-Microsoft (Microsoft's old recorded TV format); mpg (standard MPEG); and ts (raw MPEG transport stream of the kind often produced by PVRs). When these three files are played back under Windows 7, the mpg and ts files play smoothly, but the dvr-Microsoft file stutters. The last piece of data I have is that two other Windows 7 machines can play back dvr-Microsoft files smoothly with no stuttering. One is a netbook, with less grunt than the media centre. So there must be something specific about my Media Center machine that's causing the problem. Does anyone have any idea where I can look now? I don't know much about AV software, codecs, filter graphs etc. but I suspect that's where the problem lies. Rendering the video isn't the problem, but extracting the streams is. How would I go about diagnosing the problem? Edited to add: I just used the GraphStudio tool to look at the filter graph on the offending PC. The filter graph it uses by default for dvr-Microsoft looks identical to the other machines, and, interestingly, when I play the files using GraphStudio they run smoothly. Under Windows Media Player and Windows Media Center they stutter. I'd like to see the filter graph for Windows Media Player but GraphStudio won't show it. It looks like Windows Media Player and WMC are using a different decoding path to GraphStudio. Edited again to add: Today I purchased a new HDTV. The same Media Center driving the TV at 1080p is now playing back the old Recorded TV files smoothly, without stuttering. So whatever the cause of the original problem, using a different resolution seems to have removed the problem. It might also explain why nobody else has had this problem. I doubt many people use Media Centre with a 14in portable TV.

  Read the article

• Using an SSD with no AHCI [ICH7 base] - Windows 7 hangs frequently

  - by h4xnoodle

  I have a Shuttle Intel G31 + ICH7 (base -- not M/R etc) system. I just bought an OCZ Vertex 3 120gb [VTX3-25SAT3-120G] which includes the Sandforce 2218 firmware. The ICH7 does not support AHCI. I understand that this can be a problem. What I don't understand, is if it's necessary to have the proper performance of this drive. I know that without AHCI I may get a limited read/write speed -- this is fine. What my concern is, is the constant freezing/hangs I'm getting with Windows 7 on any disk activity. The 'Highest Active Time' flip-flops from 0 to 100% every minute or so regardless of large or small files. EDIT: The threads/processes with the highest response time is the kernel. I've been reading about other people with Shuttle SG31G2s, and they seem to be using SSDs no problem. Is this the controller's fault? The fact that I do not have AHCI enabled? It makes sense to me that if this SSD requires AHCI features that it would cause Windows to hang, but I would like to fully determine my situation before returning things/reformatting. To initially have my drive recognise the SSD at all, I had to change the BIOS option to Force Gen II instead of Auto for the SATA controller. I then installed Windows with no problem. There were no errors in the event log related to disk usage, but watching the perfmon I could see the highest active time and the processes (usually pagefile.sys being written to, or chrome/firefox caching) which was correlated to the hanging. So now what I need answered is: should I be returning this SSD and getting one with a different controller, or returning the SSD all-together as it will never work out and I will continue to get these hangs. Posts I've read: Windows 7 New SSD SATA AHCI? -- suggests to use AHCI http://forums.anandtech.com/showthread.php?t=2189868 -- Sandforce issues Windows 7 freezes with SSD -- and attached posts Why does my Windows 7 PC / SSD drive keep freezing? -- this is not the controller I have, but still a related issue. Windows 7 hangs after longer inactivity of user -- also tried messing with power settings with no luck. It was already set to 'Never' for turning off HDDs.

  Read the article

• Windows 7 remains powered on when restarting

  - by BombDefused

  I'm running windows 7 x64 on an MSI P67A-GD53 motherboard, in an Antec P280 Super Midi Towercase with a Corsair 650w PSU. I've just installed a second instance of windows 7 x64 on a separate disk (this is to keep my games separate from my work OS). The problem is that it appears now that I cannot restart from either instance of Windows 7. The shut down command, and sleep commands work as expected. When I try to restart, the shutdown happens but the system never reboots. Everything remains powered on, until I hold down the power button to force the power off. Ithink (but am not 100% sure) this has only started since I installed the second OS, and am assuming this has something to do with the motherboard needing to know which OS to run up again? Some other forums I've read suggest that the PSU has a major role in restart and could be at fault. Changing the boot order of the disks in the BIOS does not change anything. Any suggestions greatfully recieved! Update: I now have a reproduceable issue: I think the secondary OS install may have been a red herring. It was when windows tried to reboot during the install that I noticed the issue. After playing around with installing drivers, and rebooting many many times, I have found that it is the OC genie setting on the MSI motherboard that seems to trigger the problem. This makes sense as I only started using the OC genie feature a couple of weeks ago, and probably hadn't used restart in that time. However... simply turning off OC genie does not make the issue go away. I have to turn off OC genie, shutdown, start enter bios, go to the "Save and Exit" menu "Restore Defaults" yes to "Load optimized defaults", which will reset to clear the problem. Now when the PC boots into windows, I can restart as normal (and from the OS on either HDD). I only know how to control the issue, and don't still know the root cause. I'd like to be able to use the OC genie function if anyone can suggest a why I'm seeing this problem. Could it be that I'm drawing too much power when using OC feature?

  Read the article

• Installing nGinX Reverse Proxy on CentOS 5

  - by heavymark

  I'm trying to install nGinX as a reverse proxy on CentOS 5 with apache. The instructions to do this are here: http://wiki.mediatemple.net/w/(dv):Configure_nginx_as_reverse_proxy_web_server Note- in the instructions, for the url to get nginx I'm using the following: http://nginx.org/download/nginx-1.0.10.tar.gz Now here is my problem. After installing the required packages and running .configure I get the following: checking for OS + Linux 2.6.18-028stab094.3 x86_64 checking for C compiler ... found + using GNU C compiler + gcc version: 4.1.2 20080704 (Red Hat 4.1.2-51) checking for gcc -pipe switch ... found checking for gcc builtin atomic operations ... found checking for C99 variadic macros ... found checking for gcc variadic macros ... found checking for unistd.h ... found checking for inttypes.h ... found checking for limits.h ... found checking for sys/filio.h ... not found checking for sys/param.h ... found checking for sys/mount.h ... found checking for sys/statvfs.h ... found checking for crypt.h ... found checking for Linux specific features checking for epoll ... found checking for sendfile() ... found checking for sendfile64() ... found checking for sys/prctl.h ... found checking for prctl(PR_SET_DUMPABLE) ... found checking for sched_setaffinity() ... found checking for crypt_r() ... found checking for sys/vfs.h ... found checking for nobody group ... found checking for poll() ... found checking for /dev/poll ... not found checking for kqueue ... not found checking for crypt() ... not found checking for crypt() in libcrypt ... found checking for F_READAHEAD ... not found checking for posix_fadvise() ... found checking for O_DIRECT ... found checking for F_NOCACHE ... not found checking for directio() ... not found checking for statfs() ... found checking for statvfs() ... found checking for dlopen() ... not found checking for dlopen() in libdl ... found checking for sched_yield() ... found checking for SO_SETFIB ... not found checking for SO_ACCEPTFILTER ... not found checking for TCP_DEFER_ACCEPT ... found checking for accept4() ... not found checking for int size ... 4 bytes checking for long size ... 8 bytes checking for long long size ... 8 bytes checking for void * size ... 8 bytes checking for uint64_t ... found checking for sig_atomic_t ... found checking for sig_atomic_t size ... 4 bytes checking for socklen_t ... found checking for in_addr_t ... found checking for in_port_t ... found checking for rlim_t ... found checking for uintptr_t ... uintptr_t found checking for system endianess ... little endianess checking for size_t size ... 8 bytes checking for off_t size ... 8 bytes checking for time_t size ... 8 bytes checking for setproctitle() ... not found checking for pread() ... found checking for pwrite() ... found checking for sys_nerr ... found checking for localtime_r() ... found checking for posix_memalign() ... found checking for memalign() ... found checking for mmap(MAP_ANON|MAP_SHARED) ... found checking for mmap("/dev/zero", MAP_SHARED) ... found checking for System V shared memory ... found checking for POSIX semaphores ... not found checking for POSIX semaphores in libpthread ... found checking for struct msghdr.msg_control ... found checking for ioctl(FIONBIO) ... found checking for struct tm.tm_gmtoff ... found checking for struct dirent.d_namlen ... not found checking for struct dirent.d_type ... found checking for PCRE library ... found checking for system md library ... not found checking for system md5 library ... not found checking for OpenSSL md5 crypto library ... found checking for sha1 in system md library ... not found checking for OpenSSL sha1 crypto library ... found checking for zlib library ... found creating objs/Makefile Configuration summary + using system PCRE library + OpenSSL library is not used + md5: using system crypto library + sha1: using system crypto library + using system zlib library nginx path prefix: "/usr/local/nginx" nginx binary file: "/usr/local/nginx/sbin/nginx" nginx configuration prefix: "/usr/local/nginx/conf" nginx configuration file: "/usr/local/nginx/conf/nginx.conf" nginx pid file: "/usr/local/nginx/logs/nginx.pid" nginx error log file: "/usr/local/nginx/logs/error.log" nginx http access log file: "/usr/local/nginx/logs/access.log" nginx http client request body temporary files: "client_body_temp" nginx http proxy temporary files: "proxy_temp" nginx http fastcgi temporary files: "fastcgi_temp" nginx http uwsgi temporary files: "uwsgi_temp" nginx http scgi temporary files: "scgi_temp" It says if you get errors to stop and make sure packages are installed. I didn't get errors but as you can see I got several "not founds". Are those considered errors? If so how do I resolve that. And as noted in the link, I cannot install through yum, because it wont work with plesk then. Thanks!

  Read the article

• iptables to allow 80 and 443 on chillispot running ddwrt

  - by user76682

  I am having problems setting this up. this is what I am trying to do. I have Chillispot (hotpsot) running on dd-wrt. Everything is setup, but the client wants only 80 and 443 to go through through the hotspot. I found this tutorial for dd-wrt but that doesnt seem to work. http://www.dd-wrt.com/wiki/index.php/Iptables#Allow_HTTP_traffic_only_to_specific_domain.28s.29 Initially I tried to place the options at the top but didnt work. then i flushed the iptables and set only these three. I can see the pkts number grow but for some reason I can browse. root@DD-WRT:~# iptables -nvL FORWARD Chain FORWARD (policy ACCEPT 3105 packets, 2442K bytes) pkts bytes target prot opt in out source destination 1629 230K ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 multiport dports 21,80,443 2346 2792K ACCEPT 0 -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 328 46420 DROP 0 -- * * 0.0.0.0/0 0.0.0.0/0 Heres some info from the router, chillispot is the tun0 interface. root@DD-WRT:~# iptables -vnL FORWARD --line-numbers Chain FORWARD (policy DROP 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 0 0 ACCEPT 47 -- * vlan1 192.168.8.0/24 0.0.0.0/0 2 0 0 ACCEPT tcp -- * vlan1 192.168.8.0/24 0.0.0.0/0 tcp dpt:1723 3 32 1851 ACCEPT 0 -- tun0 * 0.0.0.0/0 0.0.0.0/0 state NEW 4 0 0 ACCEPT 0 -- br0 br0 0.0.0.0/0 0.0.0.0/0 5 48 2408 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU 6 756 452K lan2wan 0 -- * * 0.0.0.0/0 0.0.0.0/0 7 756 452K ACCEPT 0 -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 8 0 0 TRIGGER 0 -- vlan1 br0 0.0.0.0/0 0.0.0.0/0 TRIGGER type:in match:0 relate:0 9 0 0 trigger_out 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 10 0 0 ACCEPT 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 state NEW 11 0 0 DROP 0 -- * * 0.0.0.0/0 0.0.0.0/0 12 0 0 DROP 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 13 0 0 DROP 0 -- * br0 0.0.0.0/0 0.0.0.0/0 The interfaces: root@DD-WRT:~# ifconfig -a br0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F inet addr:192.168.8.1 Bcast:192.168.8.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2371 errors:0 dropped:0 overruns:0 frame:0 TX packets:1862 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:259721 (253.6 KiB) TX bytes:254862 (248.8 KiB) br0:0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:2508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1066410 (1.0 MiB) TX bytes:376001 (367.1 KiB) Interrupt:5 eth1 Link encap:Ethernet HWaddr 00:12:17:CF:80:61 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:729 errors:0 dropped:0 overruns:0 frame:114693 TX packets:697 errors:2 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107869 (105.3 KiB) TX bytes:473134 (462.0 KiB) Interrupt:4 Base address:0x1000 etherip0 Link encap:Ethernet HWaddr 1E:13:B7:09:CC:8C BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:18 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1210 (1.1 KiB) TX bytes:1210 (1.1 KiB) teql0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.182.1 P-t-P:192.168.182.1 Mask:255.255.255.0 UP POINTOPOINT RUNNING MTU:1500 Metric:1 RX packets:662 errors:0 dropped:0 overruns:0 frame:0 TX packets:587 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:92167 (90.0 KiB) TX bytes:427657 (417.6 KiB) vlan0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2371 errors:0 dropped:0 overruns:0 frame:0 TX packets:1864 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:269558 (263.2 KiB) TX bytes:262680 (256.5 KiB) vlan1 Link encap:Ethernet HWaddr 00:12:17:CF:80:60 inet addr:10.3.2.47 Bcast:10.255.255.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2675 errors:0 dropped:0 overruns:0 frame:0 TX packets:645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:705429 (688.8 KiB) TX bytes:102197 (99.8 KiB) The routing table: root@DD-WRT:~# netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.182.0 0.0.0.0 255.255.255.0 U 0 0 0 tun0 10.3.2.0 0.0.0.0 255.255.255.0 U 0 0 0 vlan1 192.168.8.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 br0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 10.3.2.1 0.0.0.0 UG 0 0 0 vlan1 Highly appreciate your help. TIA, Arun

  Read the article

• SQL server 2008 R2 installation error

  - by Sonia

  I have a windows 7,32 bit laptop. I am the administrator with all permissions. when I click on the SQL server 2008R2 set up file,it says : "SQL server set up has encountered the following error:Failed to retreive data for this request" click on OK. I have uninstalled all the components of SQL from control panel. I used Windows installer clean up to remove the files(which I must have not done ),but still no go. The summary.txt log says: Overall summary: Final result: Failed: see details below Exit code (Decimal): 847168662 Exit facility code: 638 Exit error code: 50326 Exit message: Failed to retrieve data for this request. Start time: 2012-05-25 14:59:15 End time: 2012-05-25 15:00:09 Requested action: RunRules Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\Detail.txt Exception help link: http%3a%2f%2fgo.microsoft.com%2ffwlink%3fLinkId%3d20476%26ProdName%3dMicrosoft%2bSQL%2bServer%26EvtSrc%3dsetup.rll%26EvtID%3d50000%26ProdVer%3d10.0.5500.0%26EvtType%3d0xEF814B06%400x92D13C14 Machine Properties: Machine name: EWAN-PC Machine processor count: 4 OS version: Windows Vista OS service pack: Service Pack 1 OS region: Australia OS language: English (United States) OS architecture: x86 Process architecture: 32 Bit OS clustered: No Package properties: Description: SQL Server Database Services 2008 SQLProductFamilyCode: {628F8F38-600E-493D-9946-F4178F20A8A9} ProductName: SQL2008 Type: RTM Version: 10 SPLevel: 0 Installation location: c:\385030d65c6ff61fb9\x86\setup\ Installation edition: EXPRESS User Input Settings: ACTION: RunRules CONFIGURATIONFILE: FEATURES: HELP: False INDICATEPROGRESS: False INSTANCENAME: QUIET: False QUIETSIMPLE: False RULES: GLOBALRULES,SqlUnsupportedProductBlocker,PerfMonCounterNotCorruptedCheck,Bids2005InstalledCheck,BlockInstallSxS,AclPermissionsFacet,FacetDomainControllerCheck,SSMS_IsInternetConnected,FacetWOW64PlatformCheck,FacetPowerShellCheck X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\ConfigurationFile.ini Detailed results: Rules with failures: Global rules: There are no scenario-specific rules. Rules report file: The rule result report file is not available. Exception summary: The following is an exception stack listing the exceptions in outermost to innermost order Inner exceptions are being indented Exception type: Microsoft.SqlServer.Management.Sdk.Sfc.EnumeratorException Message: Failed to retrieve data for this request. Data: HelpLink.ProdName = Microsoft SQL Server HelpLink.BaseHelpUrl = http://go.microsoft.com/fwlink HelpLink.LinkId = 20476 DisableWatson = true Stack: at Microsoft.SqlServer.Setup.Chainer.Workflow.PendingActions.InvokeActions(WorkflowObject metaDb, TextWriter loggingStream) at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionEngine.RunActionQueue() at Microsoft.SqlServer.Setup.Chainer.Workflow.Workflow.RunWorkflow(HandleInternalException exceptionHandler) at Microsoft.SqlServer.Chainer.Setup.Setup.RunRequestedWorkflow() at Microsoft.SqlServer.Chainer.Setup.Setup.Run() at Microsoft.SqlServer.Chainer.Setup.Setup.Start() at Microsoft.SqlServer.Chainer.Setup.Setup.Main() Inner exception type: Microsoft.SqlServer.Configuration.Sco.ScoException Message: Attempted to perform an unauthorized operation. Data: WatsonData = HKEY_LOCAL_MACHINE@SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\Microsoft SQL Server 10 Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Configuration.Sco.SqlRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Discovery.RegistryKeyExistsPropertyValueProvider.GetPropertyValue(Object[] context) at Microsoft.SqlServer.Discovery.DiscoveryEnumObject.GetPropertyValueFromProvider(IPropertyValueProvider propertyValueProvider, String machineName, Object[] context) at Microsoft.SqlServer.Discovery.ObjectInstanceSettings.IsObjectFound(String machineName, String idFilter) at Microsoft.SqlServer.Discovery.Product.FilterObjectSet(ArrayList objects, String idFilter) at Microsoft.SqlServer.Discovery.Product.GetData(EnumResult erParent) at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData() at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData(Request req, Object ci) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.GetData(Object connectionInfo, Request request) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.Process(Object connectionInfo, Request request) Inner exception type: System.UnauthorizedAccessException Message: Attempted to perform an unauthorized operation. Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) Ineed to install SQL server 2008 R2 for one of the company softwares to work. Any immediate help will be greatly appreciated. Thanks Sonia

  Read the article

• 500 Internal Server Error with PHP application

  - by James

  I have written a PHP application using Windows and XAMPP. I've been trying to run it on Ubuntu 10.10 with Lighttpd 1.4.26. Parts of the application work fine, but whenever I try to log in, I get a 500 - Internal Server Error page. The only thing that shows up in /var/log/lighttpd/error.log is 2011-02-25 13:43:13: (mod_fastcgi.c.2582) unexpected end-of-file (perhaps the fastcgi process died): pid: 1169 socket: unix:/tmp/php.socket-0 2011-02-25 13:43:13: (mod_fastcgi.c.3367) response not received, request sent: 1596 on socket: unix:/tmp/php.socket-0 for /~denton/customer-facing-portal/index.php?, closing connection If I had any output whatsoever from PHP, this would be a lot easier to debug. Any ideas on how to get some? Here is my /etc/lighttpd/lighttpd.conf file: # Debian lighttpd configuration file # ############ Options you really have to take care of #################### ## modules to load server.modules = ( "mod_alias", "mod_compress", # "mod_rewrite", # "mod_redirect", # "mod_usertrack", # "mod_expire", # "mod_flv_streaming", # "mod_evasive", "mod_setenv" ) ## a static document-root, for virtual-hosting take look at the ## server.virtual-* options server.document-root = "/var/www/" ## where to upload files to, purged daily. server.upload-dirs = ( "/var/cache/lighttpd/uploads" ) ## where to send error-messages to server.errorlog = "/var/log/lighttpd/error.log" ## files to check for if .../ is requested index-file.names = ( "index.php", "index.html", "index.htm", "default.htm", "index.lighttpd.html" ) ## Use the "Content-Type" extended attribute to obtain mime type if possible # mimetype.use-xattr = "enable" ## # which extensions should not be handle via static-file transfer # # .php, .pl, .fcgi are most often handled by mod_fastcgi or mod_cgi static-file.exclude-extensions = ( ".php", ".pl", ".fcgi" ) ######### Options that are good to be but not neccesary to be changed ####### ## Use ipv6 only if available. (disabled for while, check #560837) #include_shell "/usr/share/lighttpd/use-ipv6.pl" ## bind to port (default: 80) # server.port = 81 ## bind to localhost only (default: all interfaces) ## server.bind = "localhost" ## error-handler for status 404 #server.error-handler-404 = "/error-handler.html" #server.error-handler-404 = "/error-handler.php" ## to help the rc.scripts server.pid-file = "/var/run/lighttpd.pid" ## ## Format: <errorfile-prefix><status>.html ## -> ..../status-404.html for 'File not found' #server.errorfile-prefix = "/var/www/" ## virtual directory listings dir-listing.encoding = "utf-8" server.dir-listing = "enable" ### only root can use these options # # chroot() to directory (default: no chroot() ) #server.chroot = "/" ## change uid to <uid> (default: don't change) server.username = "www-data" ## change gid to <gid> (default: don't change) server.groupname = "www-data" #### compress module compress.cache-dir = "/var/cache/lighttpd/compress/" compress.filetype = ("text/plain", "text/html", "application/x-javascript", "text/css") #### url handling modules (rewrite, redirect, access) # url.rewrite = ( "^/$" => "/server-status" ) # url.redirect = ( "^/wishlist/(.+)" => "http://www.123.org/$1" ) #### expire module # expire.url = ( "/buggy/" => "access 2 hours", "/asdhas/" => "access plus 1 seconds 2 minutes") #### external configuration files ## mimetype mapping include_shell "/usr/share/lighttpd/create-mime.assign.pl" ## load enabled configuration files, ## read /etc/lighttpd/conf-available/README first include_shell "/usr/share/lighttpd/include-conf-enabled.pl" ## Set environment variables setenv.add-environment = ( "DB_URL__DEMO" => "192.168.1.231", "DB_NAME_DEMO" => "demo", "DB_USER_DEMO" => "user", "DB_PASS_DEMO" => "password", "DB_AGENCY_DEMO" => "demo" ) Here is my /etc/php5/cgi/php.ini file (sans 1641 lines of comments): [PHP] register_long_arrays = Off short_open_tag = Off engine = On short_open_tag = Off asp_tags = Off precision = 14 y2k_compliance = On output_buffering = 4096 zlib.output_compression = Off implicit_flush = Off unserialize_callback_func = serialize_precision = 100 allow_call_time_pass_reference = Off safe_mode = Off safe_mode_gid = Off safe_mode_include_dir = safe_mode_exec_dir = safe_mode_allowed_env_vars = PHP_ safe_mode_protected_env_vars = LD_LIBRARY_PATH disable_functions = disable_classes = expose_php = On max_execution_time = 30 max_input_time = 60 memory_limit = 128M error_reporting = E_ALL & ~E_DEPRECATED & ~E_STRICT display_errors = On display_startup_errors = On log_errors = On log_errors_max_len = 1024 ignore_repeated_errors = Off ignore_repeated_source = Off report_memleaks = On track_errors = On html_errors = On variables_order = "GPCS" request_order = "GP" register_globals = Off register_long_arrays = Off register_argc_argv = Off auto_globals_jit = On post_max_size = 8M magic_quotes_gpc = Off magic_quotes_runtime = Off magic_quotes_sybase = Off auto_prepend_file = auto_append_file = default_mimetype = "text/html" doc_root = user_dir = enable_dl = Off cgi.fix_pathinfo=1 file_uploads = On upload_max_filesize = 2M max_file_uploads = 20 allow_url_fopen = On allow_url_include = Off default_socket_timeout = 60 [Date] date.timezone = "America/Chicago" [filter] [iconv] [intl] [sqlite] [sqlite3] [Pcre] [Pdo] [Pdo_mysql] pdo_mysql.cache_size = 2000 pdo_mysql.default_socket= [Phar] [Syslog] define_syslog_variables = Off [mail function] SMTP = localhost smtp_port = 25 mail.add_x_header = On [SQL] sql.safe_mode = Off [ODBC] odbc.allow_persistent = On odbc.check_persistent = On odbc.max_persistent = -1 odbc.max_links = -1 odbc.defaultlrl = 4096 odbc.defaultbinmode = 1 [Interbase] ibase.allow_persistent = 1 ibase.max_persistent = -1 ibase.max_links = -1 ibase.timestampformat = "%Y-%m-%d %H:%M:%S" ibase.dateformat = "%Y-%m-%d" ibase.timeformat = "%H:%M:%S" [MySQL] mysql.allow_local_infile = On mysql.allow_persistent = On mysql.cache_size = 2000 mysql.max_persistent = -1 mysql.max_links = -1 mysql.default_port = mysql.default_socket = mysql.default_host = mysql.default_user = mysql.default_password = mysql.connect_timeout = 60 mysql.trace_mode = Off [MySQLi] mysqli.max_persistent = -1 mysqli.allow_persistent = On mysqli.max_links = -1 mysqli.cache_size = 2000 mysqli.default_port = 3306 mysqli.default_socket = mysqli.default_host = mysqli.default_user = mysqli.default_pw = mysqli.reconnect = Off [mysqlnd] mysqlnd.collect_statistics = On mysqlnd.collect_memory_statistics = Off [OCI8] [PostgresSQL] pgsql.allow_persistent = On pgsql.auto_reset_persistent = Off pgsql.max_persistent = -1 pgsql.max_links = -1 pgsql.ignore_notice = 0 pgsql.log_notice = 0 [Sybase-CT] sybct.allow_persistent = On sybct.max_persistent = -1 sybct.max_links = -1 sybct.min_server_severity = 10 sybct.min_client_severity = 10 [bcmath] bcmath.scale = 0 [browscap] [Session] session.save_handler = files session.use_cookies = 1 session.use_only_cookies = 1 session.name = PHPSESSID session.auto_start = 0 session.cookie_lifetime = 0 session.cookie_path = / session.cookie_domain = session.cookie_httponly = session.serialize_handler = php session.gc_probability = 1 session.gc_divisor = 1000 session.gc_maxlifetime = 1440 session.bug_compat_42 = Off session.bug_compat_warn = Off session.referer_check = session.entropy_length = 0 session.cache_limiter = nocache session.cache_expire = 180 session.use_trans_sid = 0 session.hash_function = 0 session.hash_bits_per_character = 5 url_rewriter.tags = "a=href,area=href,frame=src,input=src,form=fakeentry" [MSSQL] mssql.allow_persistent = On mssql.max_persistent = -1 mssql.max_links = -1 mssql.min_error_severity = 10 mssql.min_message_severity = 10 mssql.compatability_mode = Off mssql.secure_connection = Off [Assertion] [COM] [mbstring] [gd] [exif] [Tidy] tidy.clean_output = Off [soap] soap.wsdl_cache_enabled=1 soap.wsdl_cache_dir="/tmp" soap.wsdl_cache_ttl=86400 soap.wsdl_cache_limit = 5 [sysvshm] [ldap] ldap.max_links = -1 [mcrypt] [dba] Update: here is /etc/lighttpd/conf-enabled/15-fastcgi-php.conf As far as I know, it's just the default config file the Ubuntu package installed. ## FastCGI programs have the same functionality as CGI programs, ## but are considerably faster through lower interpreter startup ## time and socketed communication ## ## Documentation: /usr/share/doc/lighttpd-doc/fastcgi.txt.gz ## http://redmine.lighttpd.net/projects/lighttpd/wiki/Docs:ConfigurationOptions#mod_fastcgi-fastcgi ## Start an FastCGI server for php (needs the php5-cgi package) fastcgi.server += ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 1, "idle-timeout" => 20, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "4", "PHP_FCGI_MAX_REQUESTS" => "10000" ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" )) )

  Read the article

• VPN Connection causes DNS to use wrong DNS server

  - by Bryan

  I have a Windows 7 PC on our company network (which is a member of our Active Directory). Everything works fine until I open a VPN connection to a customer's site. When I do connect, I lose network access to shares on the network, including directories such as 'Application Data' that we have a folder redirection policy for. As you can imagine, this makes working on the PC very difficult, as desktop shortcuts stop working, software stops working properly due to having 'Application Data' pulled from under it. Our network is routed (10.58.5.0/24), with other local subnets existing within the scope of 10.58.0.0/16. The remote network is on 192.168.0.0/24. I've tracked the issue down to being DNS related. As soon as I open the VPN tunnel, all my DNS traffic goes via the remote network, which explains the loss of local resources, but my question is, how can I force local DNS queries to go to our local DNS servers rather than our customers? The output of ipconfig /all when not connected to the VPN is below: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled This is the output of the same command with the VPN tunnel connected: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local PPP adapter Customer Domain: Connection-specific DNS Suffix . : customerdomain.com Description . . . . . . . . . . . : CustomerDomain Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.85(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.0.16 192.168.0.17 Primary WINS Server . . . . . . . : 192.168.0.17 NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled Routing table Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.58.5.1 10.58.5.89 20 10.58.5.0 255.255.255.0 On-link 10.58.5.89 276 10.58.5.89 255.255.255.255 On-link 10.58.5.89 276 10.58.5.255 255.255.255.255 On-link 10.58.5.89 276 91.194.153.42 255.255.255.255 10.58.5.1 10.58.5.89 21 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 192.168.0.95 192.168.0.85 21 192.168.0.85 255.255.255.255 On-link 192.168.0.85 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.58.5.89 276 224.0.0.0 240.0.0.0 On-link 192.168.0.85 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.58.5.89 276 255.255.255.255 255.255.255.255 On-link 192.168.0.85 276 The binding order for the interfaces is as follows: I've not configured the VPN tunnel to use the default gateway at the remote end, and network comms to nodes on both networks are fine. (i.e. I can ping any node on our network or the remote network). I've modified the PPTP connection properties to use the DNS servers 10.58.3.32 followed by 192.168.0.16, yet the query still goes to 192.168.0.16. Edit: The local resources that disappear are hosted on domain DFS roots, which might (or might not) be relevant.

  Read the article

• Abnormal hangs and restarts Ubuntu 8.04

  - by jai-ho

  Hi, I am using Ubuntu 8.04 LTS and seeing the following behaviors: The system hangs after a while and becomes completely unresponsive. The system sometimes restarts itself ! Can you please help me identify what is the problem? Also please mention where should I look for the possible cause of this error. Thanks. EDIT: Got the following from the dmesg output (the system got hung and had to restart) [ 15.452015] Driver 'sr' needs updating - please use bus_type methods [ 15.456882] Driver 'sd' needs updating - please use bus_type methods [ 15.457987] sr0: scsi3-mmc drive: 52x/52x writer cd/rw xa/form2 cdda tray [ 15.457993] Uniform CD-ROM driver Revision: 3.20 [ 15.458058] sr 0:0:1:0: Attached scsi CD-ROM sr0 [ 15.463028] sd 1:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) [ 15.463051] sd 1:0:0:0: [sda] Write Protect is off [ 15.463055] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 15.463083] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 15.463151] sd 1:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) [ 15.463167] sd 1:0:0:0: [sda] Write Protect is off [ 15.463171] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 15.463197] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 15.463202] sda:<5sr 0:0:1:0: Attached scsi generic sg0 type 5 [ 15.464634] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 15.470120] sda1 sda2 < sda5 [ 15.495536] sd 1:0:0:0: [sda] Attached SCSI disk [ 15.759549] Attempting manual resume [ 15.759554] swsusp: Resume From Partition 8:5 [ 15.759556] PM: Checking swsusp image. [ 15.759742] PM: Resume from disk failed. [ 15.779964] EXT3-fs: INFO: recovery required on readonly filesystem. [ 15.779970] EXT3-fs: write access will be enabled during recovery. [ 19.904204] kjournald starting. Commit interval 5 seconds [ 19.904235] EXT3-fs: sda1: orphan cleanup on readonly fs [ 19.904245] ext3_orphan_cleanup: deleting unreferenced inode 303260 [ 19.904304] ext3_orphan_cleanup: deleting unreferenced inode 303329 [ 19.932763] ext3_orphan_cleanup: deleting unreferenced inode 3801871 [ 19.932785] ext3_orphan_cleanup: deleting unreferenced inode 3801874 [ 19.932798] ext3_orphan_cleanup: deleting unreferenced inode 3801910 [ 19.951253] ext3_orphan_cleanup: deleting unreferenced inode 3801912 [ 19.951266] ext3_orphan_cleanup: deleting unreferenced inode 3801914 [ 19.951278] ext3_orphan_cleanup: deleting unreferenced inode 3959212 [ 19.951299] ext3_orphan_cleanup: deleting unreferenced inode 3959213 [ 19.960335] ext3_orphan_cleanup: deleting unreferenced inode 3959215 [ 19.963531] ext3_orphan_cleanup: deleting unreferenced inode 3801875 [ 19.963545] ext3_orphan_cleanup: deleting unreferenced inode 3663727 [ 19.963565] ext3_orphan_cleanup: deleting unreferenced inode 3663708 [ 19.963577] ext3_orphan_cleanup: deleting unreferenced inode 4072122 [ 19.963597] ext3_orphan_cleanup: deleting unreferenced inode 4072157 [ 19.968616] ext3_orphan_cleanup: deleting unreferenced inode 4072159 [ 19.970252] ext3_orphan_cleanup: deleting unreferenced inode 4072160 [ 19.970264] ext3_orphan_cleanup: deleting unreferenced inode 4072161 [ 19.992889] ext3_orphan_cleanup: deleting unreferenced inode 4072264 [ 19.992903] ext3_orphan_cleanup: deleting unreferenced inode 4072267 [ 19.999585] ext3_orphan_cleanup: deleting unreferenced inode 4072268 [ 20.008329] ext3_orphan_cleanup: deleting unreferenced inode 4072270 [ 20.008343] ext3_orphan_cleanup: deleting unreferenced inode 4072123 [ 20.008360] ext3_orphan_cleanup: deleting unreferenced inode 4072452 [ 20.008374] ext3_orphan_cleanup: deleting unreferenced inode 4072453 [ 20.008385] ext3_orphan_cleanup: deleting unreferenced inode 4072124 [ 20.008398] ext3_orphan_cleanup: deleting unreferenced inode 311574 [ 20.008413] ext3_orphan_cleanup: deleting unreferenced inode 967890 [ 20.008420] EXT3-fs: sda1: 28 orphan inodes deleted [ 20.008423] EXT3-fs: recovery complete. [ 20.082622] EXT3-fs: mounted filesystem with ordered data mode. [ 29.025379] input: PC Speaker as /devices/platform/pcspkr/input/input2 [ 29.187133] Linux agpgart interface v0.102 [ 29.225338] iTCO_vendor_support: vendor-support=0 [ 29.259662] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)

  Read the article

• Trust Bluetooth 4.0 and Bluetooth Headset

  - by Seregwethrin

  Firstly, I'm writing this after 5 hours of nonstop struggle to make it work, so I searched into the deepest websites from Google, and tried many things. I have Trust Bluetooth 4.0 USB adapter (link) Samsung HM1500 Bluetooth Headset Windows 7 64-bit Desktop PC Facts Nothing wrong with the headset. (it works, tested on a phone and a laptop. Problem is all about bluetooth dongle and its driver.) Trust BT adapter can send and receive files even without any driver. I can pair successfully without any driver too. In Headset's Properties, Services tab, Handsfree and Headset services are checked. Problem When I pair with my BT headset, I cannot see it as a sound playback device. Also when I double-click the headset device icon in Bluetooth Devices, in laptop: it opens a connection window where I can connect and disconnect to that device - perfect! in desktop: it opens the properties window, even though Handsfree and Headset services are checked (I check them explicitly, in laptop they came as already checked) - Problem! Unsuccessful driver installations The driver on the Trust's website says "Error 1606 Could not access Network Location" on start, so it doesn't get installed. The driver on Broadcom (link) is being closed with Windows's that classic "has stopped working" error on validation step, so it doesn't get installed too. (Those tests made more than once) Successful installation In the Win64 folder of Trust's driver from their website, if I install through "BTW.msi", it doesn't give me Error 1606 and it gets installed. Then the problem: When I try to start bluetooth from start menu (or it gets started at Windows startup), an error popup says: "BtBalloon.dll is missing..." so it doesn't start. I found BBalloon.dll in the driver folder, I renamed it to BtBalloon.dll, moved into Windows/system32 and Windows/SysWOW64 folders, and it seems working. Or maybe it gets closed behind the scenes. The bluetooth icon is there with or without this driver since Windows has it. Bluetooth Peripheral Device First it didn't get installed from Windows Update. After, I showed the driver folder path in Device Manager and pressed "Explore in this location". Surprisingly, it's being found as "Handsfree" driver. Now even I uninstall the drivers, it still can see the Handsfree. But still, no playback device. Any ideas to guide me? I'm out of ideas.

  Read the article

• Critique My Backup and Storage Plan

  - by MetaHyperBolic

  My current storage (RAID-1 off of a hardware RAID card) and backup (a spare drive) solutions for my home network are inadequate. I have too much data scattered on various one-off drives. It is time to evolve. Backups seem simple enough, at least: lots of big drives. However, I am bewildered by the number of choices for small home storage. The Drobo S looks appealing. So does the ReadyNAS. I am not looking for bunches of shiny features, I'm mostly interested in reliability. I am not interested in building Yet Another PC to create a file server or doing something in the cloud, or whatever. I'm stupid, so I am keeping it simple. Requirements for Main Volume: Starting working space roughly 2TB, with options for growth up to 5TB RAID or something RAID-like with at least one parity drive eSATA II for speed during backups Ability to shut down gracefully when alerted of low power by a UPS Optional but Desirable: Will take 2TB drives now with options for the larger 3TB drives coming in 2010-2011 Optional but Desirable: : RAID-6 or something similar, with two parity drives Optional but Desirable: : Hot spare Ethernet connection not required, as the volume will be shared via the same machines which runs my home print server Backups: Backup performed via ROBOCOPY in mirror mode to an external hard drive via a eSATA II connection. Start with rotating between two external 2TB hard drives, will go up to six external 2TB drives. Start with a weekly backup, move to a bi-weekly backup as more drives are added. Move to 3TB drives as the size of my main volume increases. Backup drives will be stored on an off-site location. Hard drives: I plan on buying all of the same model, but different batches from different vendors. I found a "burn-in" utility with which I can pound away on the drives for a couple of weeks before adding them to the backup pool or the main volume. I estimate that I am looking at roughly $1,500 to start, once I start throwing in two TB drives for backup and four for storage. So, are there any obvious flaws in my plan? What have I overlooked? Any suggestions for the storage device for my main volume that fits my requirements? Or do I just keep it simple, 2 drives in RAID-1, then perform due diligence with my backups, accepting that I will have to buy a whole new unit when my data grows past 2TB?

  Read the article

• TomCat starts, but does not load properly

  - by user37136

  Hey guys, I've been working on this for a day now and still don't know what's wrong. I am essentially building a second environment for our web and app server. I got apache to load up just fine, but tomcat is proving to be difficult. It appears to start and load just fine, but when it comes to loading our application, its just got stuck for 2-5 minutes and then shut down. Here is the log on the original machine where it works fine: 2010-02-12 11:52:40,506 INFO Web application servlet context is initializing... 2010-02-12 11:52:40,540 DEBUG Servlet context attribute added: select_jobType=[{1,Undefined}, {100,Completion}, {200,Plugging}, {300,R+M}, {400,Workover}, {500,Swab - tubing}, {600,Swab - fluid}] 2010-02-12 11:52:40,540 DEBUG Servlet context attribute added: select_jobTaskType=[{1,Undefined}, {100,Rod part}, {200,Tubing leak}, {300,Pump change}, {400,Stripping job}, {500,Long stroke}, {600,A/L optimization}] 2010-02-12 11:52:40,541 DEBUG Servlet context attribute added: select_wellType=[{1,Undefined}, {100,Rod pump}, {200,ESP}, {300,Injector}, {400,PC pump}, {500,Co-Rod}, {600,Flowing}, {700,Storage}] 2010-02-12 11:52:40,541 DEBUG Servlet context attribute added: select_assetType=[{1,Rig}, {100,Disabled rig}] 2010-02-12 11:52:40,542 DEBUG Servlet context attribute added: select_state=[{AL,Alabama}, {AK,Alaska}, {AZ,Arizona}, {AR,Arkansas}, {CA,California}, {CO,Colorado}, {CT,Connecticut}, {DE,Delaware}, {FL,Florida}, {GA,Georgia}, {HI,Hawaii}, {ID,Idaho}, {IL,Illinois}, {IN,Indiana}, {IA,Iowa}, {KS,Kansas}, {KY,Kentucky}, {LA,Louisiana}, {ME,Maine}, {MD,Maryland}, {MA,Massachusetts}, {MI,Michigan}, {MN,Minnesota}, {MS,Mississippi}, {MO,Missouri}, {MT,Montana}, {NE,Nebraska}, {NV,Nevada}, {NH,New Hampshire}, {NJ,New Jersey}, {NM,New Mexico}, {NY,New York}, {NC,North Carolina}, {ND,North Dakota}, {OH,Ohio}, {OK,Oklahoma}, {OR,Oregon}, {PA,Pennsylvania}, {RI,Rhode Island}, {SC,South Carolina}, {SD,South Dakota}, {TN,Tennessee}, {TX,Texas}, {UT,Utah}, {VT,Vermont}, {VA,Virginia}, {WA,Washington}, {WV,West Virginia}, {WI,Wisconsin}, {WY,Wyoming}, {ACO,Atlantic Coast Offshore}, {FOAK,Federal Offshore Alaska}, {NGOM,Northern Gulf of Mexico}, {PCO,Pacific Coastal Offshore}] 2010-02-12 11:52:40,542 INFO KeyviewContextMonitor.contextInitialized: Loaded drop-down lists:com/key/portal/web/common/lists.properties 2010-02-12 11:52:40,937 DEBUG Servlet context attribute added: org.apache.struts.action.SERVLET_MAPPING=*.do 2010-02-12 11:52:40,937 DEBUG Servlet context attribute added: org.apache.struts.action.ACTION_SERVLET=org.apache.struts.action.ActionServlet@155d578 2010-02-12 11:52:41,939 DEBUG Servlet context attribute added: org.apache.struts.action.MODULE=org.apache.struts.config.impl.ModuleConfigImpl@e08e9d 2010-02-12 11:52:41,962 DEBUG Servlet context attribute added: org.apache.struts.action.FORM_BEANS=org.apache.struts.action.ActionFormBeans@b31c3c 2010-02-12 11:52:41,967 DEBUG Servlet context attribute added: org.apache.struts.action.FORWARDS=org.apache.struts.action.ActionForwards@102c646 2010-02-12 11:52:41,973 DEBUG Servlet context attribute added: org.apache.struts.action.MAPPINGS=org.apache.struts.action.ActionMappings@127276a 2010-02-12 11:52:41,974 DEBUG Servlet context attribute added: org.apache.struts.action.MESSAGE=org.apache.struts.util.PropertyMessageResources@18cae13 2010-02-12 11:52:41,984 DEBUG Servlet context attribute added: org.apache.struts.action.PLUG_INS=[Lorg.apache.struts.action.PlugIn;@f875ae 2010-02-12 11:52:46,816 INFO Sucessfully loaded application properties com/key/core/properties/application On my second environment, it didn't execute the last line. I start tomcat with the exact same command line !/bin/ksh export JAVA_HOME=/app/java export CATALINA_HOME=/app/tomcat export CATALINA_BASE=/app/keyview/appserver CATALINA_OPTS=" -Xms128m -Xmx800m -Dapplication.props=com/key/core/properties/application -Dlog4j.configuration=com/key/core/log/log4j.xml -Djava.awt.headless=true -Dlog4j.debug" export CATALINA_OPTS ${CATALINA_HOME}/bin/startup.sh I bolded the line that I think are in error. Thanks

  Read the article

• Problems updating to Windows 8.1

  - by user52428

  yesterday I attempted to upgrade to windows 8.1 from windows 8. My brother downloaded it on his computer the day before then. I got it from the Windows store. It downloaded and prompted me to restart so I did. It just had the windows 8 loading screen with the HP sign above it, no percentages or anything else, I waited for about 2 hours and while I was waiting I did some research. After reading I saw it could take 20 minutes to an hour to update, but it had already been 2 hours. I read another article and it said someone restarted their computer and it restored to windows 8.0. That's what I did and it worked. So I tried again and the same thing happens, so instead of waiting I decided I would just restart it again. I tried again and this time it showed a percentage it said,"Setting Up" After it reached 100% it went back to what happened before HP sign and just loaded again, I thought it would be different this time because it did show percentages. I waited an hour and nothing happened so I restarted the computer again. This time when I restarted it, it didn't restore, so I turned the laptop of for around 30 minutes turned it back on and it said,"Attempting to restore to previous version of Windows" It said that for around 10 minutes and it restored, so I shut downed my computer for an hour and did some more research, later I found that I needed to update my drivers my drivers we're updated so I did some more research after this I saw I needed to search for updates via: SettingsChange PC settingsWindows Update. It said I already had automatic updates on, I decided to check for updates and it said there was one update scheduled for Saturday. I didn't think this could change anything so I updated what I could. I tried to install it again it was around 11:30 last night when it was done downloading and it prompted me to restart but I had gone to sleep. I woke up today and saw it showed the HP sign and loaded again. I tried restarting it again but this didn't work I had to shut it of for 30 minutes and try again and it worked. So now I'm posting this seeing If I can get any help with this problem. Any help is appreciated. Thanks!

  Read the article

• Can't send email through Comcast SMTP to my domains

  - by Midnight Oil

  I am a Comcast customer with 3 computers and 3 computer users in the house. There are 2 fully updated Macs and one PC running Windows 7. We use Mail on the Macs, and Outlook on Windows 7. All computer accounts are configured to send mail through port 587 of smtp.comcast.net. I also have two personal domains registered with Network Solutions. For the sake of this discussion, call my domains myOwnDomain1.com and myOwnDomain2.com. I have email addresses at both domains. They are of the form [email protected] and [email protected]. Until recently, our email worked as expected. However, sometime between September 13, 2012 and September 19, 2012, we lost the ability to send email through Comcast's SMTP server to the email addresses at my personal domains. If we attempt to send email through Comcast's SMTP to those addresses, the email never arrives. Furthermore, the email clients give no indication of failure. The email just never arrives. The result is the same on all 3 computers and with all accounts on those computers. We can successfully send email through Comcast's SMTP from any of our accounts on any of our computers to any email address other than to my email addresses at my personal domains! However, I receive email at those domains that is not sent through smtp.comcast.net. For example, I can successfully send email from my gmail and yahoo accounts to my email addresses at my personal domains. Furthermore, I can successfully send email through smtp.myOwnDomain1.com to [email protected] and through smtp.myOwnDoman2.com to [email protected]. Comcast says the problem must be at Network Solutions. According to Network Solutions, their logs show they are not blocking reception of the email, and our IP address is not flagged as a spam source. They say the email is simply not arriving. Does anyone have any ideas why we can't send email through Comcast's SMTP server to my domains? As an odd coincidence, we recently noticed a change in Comcast's SMTP service. there is now a 5 minute delay on all outbound mail. Comcast's SMTP server seems to sit on the mail with a 5 minute timer.

  Read the article

< Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >