Search Results

Search found 13404 results on 537 pages for 'george host'.

Page 443/537 | < Previous Page | 439 440 441 442 443 444 445 446 447 448 449 450  | Next Page >

  • asterisk extensions.conf & sip.conf

    - by Josh
    I'm trying to get my Dialplan to work. When I call, the only thing I get is a dial tone to enter extension "no Background(thanks-calling) is played". When extension 123 is dialed, busy signal is triggered and asterisk CLI get frozen. Any help will be appreciate it. Conf files below. ; PSTN on sip.conf [pstn] type=friend host=dynamic context=pstn username=pstn secret=password nat=yes canreinvite=no dtmfmode=rfc2833 qualify=yes insecure=port,invite disallow=all allow=ulaw ; PSTN on extensions.conf [pstn] exten => s,1,Answer exten => s,2,Wait,2 exten => s,4,DigitTimeout,5 exten => s,5,ResponseTimeout,10 exten => s,6,Background(thanks-calling) exten => 0,1,Goto(incoming,123,1) ; (Member Services) [incoming] exten => 123,1,NoOP(${CALLERID}) ; show the caller ID info in the console exten => 123,n,Ringing() exten => 123,n,Answer() exten => 123,n,Playback(silence/1) exten => 123,n,Playback(connecting1) exten => 123,n,Wait(3) exten => 123,n,Dial(SIP/line1,60) exten => 123,n,Congestion

    Read the article

  • ESX hosts lose connectivity with iSCSI SAN LUNs

    - by Themist
    I've been experiencing this issue for a couple of months now where my ESX hosts lose connectivity with my iSCSI SAN vmfs volumes. As a results the ESX hosts enter a nonresponsive mode the associated VMs disconnect and the only remedy is to reboot the host. This issue happens randomly . I have escalated this issue with VMWare but I haven't had any solution to the issue yet. I see no errors on my switches and there are no hardware issues as well. My SAN infrastucture is solid and there are 2 paths for every vmfs volume. Did anybody else experienced a similar issue? edit: Here are some more details: The iSCSI SAN software is Datacore Sanmelody 2.0.4.2 running on 2 HP Proliant G5 servers. The storage attached to each of the servers is an HP MSA70 and all the iSCSI SAN Volumes that are presented to my 4 ESX hosts are mirrored. I have two iSCSI swithces HP Procurve 1800G-24 that are trunked together. My SANLELODY servers are using NC360T NICs. I team two NICs and have one cable connecting to each iSCSi switch. Each ESX server uses two NICs as well for the iSCSI Network.

    Read the article

  • Windows 2012 RDS Temporary profile for Administrator

    - by Fabio
    I've configured a Windows 2012 RDS Farm with two virtual servers (VMWare - each one on a different ESX server). Both servers have Licensing, Web Access, Gateway, Connection Broker and Session Host roles. High Availability is set up and it works fine. Remote Apps are working and even Windows XP clients have access to the web interface. User profile path is \vmfiles1\UserProfileDisks\App\ and almost everyone has full right access to it. The problem I have is that I would like to be able to access both servers at the same time with the Administrator account (console), but each time I try, the second server that I logon to give me access with a temporary profile. I tried to enable/disable multiple sessions per user and forced Admin logoff with the GPO but nothing changed. Another thing is that the server pool is not saved, so each time I restart the RDS server or I logoff from it, I have to add a server in the server manager. Do you have any idea? Sorry if my english is not perfect.

    Read the article

  • Clustering filesystem for small files

    - by viraptor
    Hi, I'm looking for a distributed filesystem which I could use for storing lots of small files (<1MB usually). What I want to get is: 2 servers which have the fs mounted themselves and mirror the data locking support (among reachable nodes) some kind of best-effort automatic resynchronisation after one node goes down and comes back again What I mean by the resync is that, I'm ok with both servers doing read/write operations even if they split-brain. I'm also ok if a local process obtains a lock if the other host is not reachable. From the resync I expect only a file-level consistent view after a while - that is - if file x is modified on both nodes during a split-brain, I don't really care which one is available after they join again, as long as it's full file, not one block coming from node1 and another block from node2. Is there a solution like that out there? I see that gluster has some problems with file locks (even in 3.1). I also noticed that OCFS2 will panic if both nodes split-brain. What other filesystem would allow me to do what I want?

    Read the article

  • How to unblacklist an IP at Google?

    - by DJRayon
    I own a small business with two servers for webhosting. When setting up the primary (CentOS 5.5 + WHM, secondary is WHM DNS Only) server I kinda messed up the firewall, so the hackers could send stuff from my server. My primary IP is x.y.29.218. Anyway - I got blacklisted in several places, but now those blacklistings are gone. For a week or so, but Google still has my IP blacklisted. I handling serious damages because of that. Many clients want to switch from my hosting, etc. I've fixed the hole with CSF firewall SMTP_BLOCK option and enabled also the WHM SMTP TEAK Currently all I see from the Main Email View Mail Statistics (Errors section) in WHM is rows and rows of the following message removed-the-email-address-for-security R=lookuphost T=remote_smtp: SMTP error from remote mail server after end of data: host aspmx.l.google.com [a.b.39.27]: 550-5.7.1 [x.y.29.218 1] Our system has detected an unusual rate of\n550-5.7.1 unsolicited mail originating from your IP address. To protect our\n550-5.7.1 users from spam, mail sent from your IP address has been blocked.\n550-5.7.1 Please visit http://www.google.com/mail/help/bulk_mail.html to review\n550 5.7.1 our Bulk Email Senders Guidelines. h24si3868764fas.171 What are my options? I have one IP free. How can I configure Exim to send mail from that IP? My brain is like constantly blowing up because of this problem. Please someone, who has any knowledge how to deal with the current situation, please give me some kind of help - any help, suggestions, etc. I've tried everything I know, and I still don't know much, because this is the first time (I just started to webhost, etc) I deal with real physical servers not some kind of pre-setup VPS solution. Many - many thanks, whoever has time to offer some help.

    Read the article

  • BackupExec 12 + RALUS - VERY slow backups

    - by LVDave
    We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

    Read the article

  • Overriding vhost.conf to always allow PHP include access to directory

    - by Jeremy Dentel
    My predecessor in my job developed a simplistic newsletter system for our school's newspaper utilizing PEAR's Mail package. As I grow this system (and our site) we are constantly stuck with Plesk rewriting the vhost.conf file in which the PEAR include path has been manually entered. This has become an unwieldy task to actually manage and keep running. There's been a "note" from both the previous developer and I to attempt to solve this problem, but we can't entirely figure it out. I'm attempting a move to cPanel through another host, so hopefully it'll go away there, but until then, it can be tedious extremely difficult to get a solid uptake of the system without constant "web-presence." I've searched around and haven't found a solution. I'm rather new to the server management scene (command line was non-existant till around a year ago. =/), so I haven't found anything. Any help would be useful. "Similar Questions" popped this up, but it still seems to rely on vhost.conf, and will still allow changes within Plesk to overwrite the changes.

    Read the article

  • "Server Unavailable" and removed permissions on .NET sites after Windows Update

    - by tags2k
    Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

    Read the article

  • Vlans and subinterfaces

    - by Adeodatus
    I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

    Read the article

  • No audio in my ubuntu system

    - by hap497
    Hi, I am running ubuntu 9.10. But there is no sound in my environment. When I go to System-Preference, there is no 'sound' entry there. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I82801AAICH [Intel 82801AA-ICH], device 0: Intel ICH [Intel 82801AA-ICH] Subdevices: 1/1 Subdevice #0: subdevice #0 $ lsmod Module Size Used by usb_storage 52576 3 binfmt_misc 8356 1 vboxvfs 34620 0 vboxvideo 1884 1 drm 159584 2 vboxvideo agpgart 34988 1 drm snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 snd_seq_oss 28576 0 iptable_filter 3100 0 snd_seq_midi 6432 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi ppdev 6688 0 snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq psmouse 56500 0 serio_raw 5280 0 snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_ oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_ti mer,snd_seq_device i2c_piix4 9932 0 parport_pc 31940 0 soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm vboxguest 143836 7 vboxvfs lp 8964 0 parport 35340 3 ppdev,parport_pc,lp pcnet32 32644 0 mii 5212 1 pcnet32 floppy 54916 0 ~:987:2$ lspci 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02) 00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] 00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter 00:03.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 40) 00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service 00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01) 00:06.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 0 00:0b.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller ~:988:3$

    Read the article

  • Use Apache authentication to Segregate access to Subversion subdirectories

    - by Stefan Lasiewski
    I've inherited a Subversion repository, running on FreeBSD and using Apache2.2 . Currently, we have one project, which looks like this. We use both local files and LDAP for authentication. <Location /> DAV svn SVNParentPath /var/svn AuthName "Staff only" AuthType Basic # Authentication through Local file (mod_authn_file), then LDAP (mod_authnz_ldap) AuthBasicProvider file ldap # Allow some automated programs to check content into the repo # mod_authn_file AuthUserFile /usr/local/etc/apache22/htpasswd Require user robotA robotB # Allow any staff to access the repo # mod_authnz_ldap Require ldap-group cn=staff,ou=PosixGroup,ou=foo,ou=Host,o=ldapsvc,dc=example,dc=com </Location> We would like to allow customers to access to certain subdirectories, without giving them global access to the entire repository. We would prefer to do this without migrating these sub-directories to their own repositories. Staff also need access to these subdirectories. Here's what I tried: <Location /www.customerA.com> DAV svn SVNParentPath /var/svn # mod_authn_file AuthType Basic AuthBasicProvider file AuthUserFile /usr/local/etc/apache22/htpasswd-customerA Require user customerA </Location> <Location /www.customerB.com> DAV svn SVNParentPath /var/svn # mod_authn_file AuthType Basic AuthBasicProvider file AuthUserFile /usr/local/etc/apache22/htpasswd-customerB Require user customerB </Location> I've tried the above. Access to '/' works for staff. However, access to /www.customerA.com and /www.customerB.com does not work. It looks like Apache is trying to authenticate the 'customerB' against LDAP, and doesn't try local password file. The error is: [Mon May 03 15:27:45 2010] [warn] [client 192.168.8.13] [1595] auth_ldap authenticate: user stefantest authentication failed; URI /www.customerB.com [User not found][No such object] [Mon May 03 15:27:45 2010] [error] [client 192.168.8.13] user stefantest not found: /www.customerB.com What am I missing?

    Read the article

  • Measure Total Bandwidth for Billing

    - by TonyZ
    I am setting up a new network which customers will host their applications on. It needs to be able to scale out to a few hundred servers and each server will have several VMs on it. Right now in my test environment, after the telco router, we are using a Linux router/firewall which is then connected to a Layer 2 switch. Could be a layer 3 in the future. I need to track total bandwidth per VM for each machine, and I need to do it in a way that it is not part of the VM. Each VM will have a private class ip address which is Natted by the gateway, or we may eventually run more than firewall/reverse proxy off a layer 3 switch. So my thinking is that I can do it off of a promiscuous port on the switches, or at the gateway firewall. I would like to have an out of the box solution, preferably open source. Does anyone have suggestions on the easiest way to set this up, and the easiest tool to use. I have looked at the web sites for Nagios, Zenoss, Zabbix, ntops on the firewall, etc. It is hard to ascertain just from the web sites if they do exactly this or not. Obviously, performance is also somewhat key here. Anything running on the gateway should not drag it down doing traffic accounting. Thanks for any thoughts. Tony Zakula

    Read the article

  • Windows 2008 R2 Servers Sending Arp Requests for IPs outside Subnet

    - by Kyle Brandt
    By running a packet capture on my my routers I see some of my servers sending ARP requests for IPs that exist outside of its network. For example if my network is: Network: 8.8.8.0/24 Gateway: 8.8.8.1 (MAC: 00:21:9b:aa:aa:aa) Example Server: 8.8.8.20 (MAC: 00:21:9b:bb:bb:bb) By running a capture on the interface that has 8.8.8.1 I see requests like: Sender Mac: 00:21:9b:bb:bb:bb Sender IP: 8.8.8.20 Target MAC: 00:21:9b:aa:aa:aa Target IP: 69.63.181.58 Anyone seen this behavior before? My understanding of ARP is that requests should only go out for IPs within the subnet... Am I confused in my understanding of ARP? If I am not confused, anyone seen this behavior? Also, these seem to happen in bursts and it doesn't happen when I do something like ping an IP outside of the network. Update: In response to Ian's questions. I am not running anything like Hyper-V. I have multiple interfaces but only one is active (Using BACS failover teaming). The subnet mask is 255.255.255.0 (Even if it were something different it wouldn't explain an IP like 69.63.181.58). When I run MS Network Monitor or wireshark I do not see these ARP requests. What happens is that on the router capturing I see a burst of about 10 requests for IPs outside of the network from the host machine. On the machine itself using wireshark or NetMon I see a flood of ARP responses for all the machines on the network. However, I don't see any requests in the capture asking for those responses. So it seems like maybe it is maybe refreshing the arp cache but including IPs that outside of the network. Also when it does this NetMon doesn't show the ARP requests?

    Read the article

  • How can I change the default location/action of 'Open Outlook Data File' in Outlook 2010?

    - by Chadddada
    I have recently deployed a Remote Desktop Host server that functions as a remote Microsoft Office 2010 work space for users. In part of the locking down of this server I have installed all programs on the D: drive and, through the use of Group Policy, hidden all the drives on the server from standard users. In addition to hiding these drives I am not allowing users to save anything locally (on the server) or open Libraries. However one of the functions of the server is to provide the Outlook client. Often users will have the .PST file stored on a network location and want to open this in Outlook. Can I change the default action or location that File Open Open Outlook Data File looks or tries to pull the file from? The default location seems to be under Users / Libraries. When click 'Open' you get a warning: This operation has been cancelled due to restrictions in effect on this computer. Clicking OK drops the user into a small menu that shows attached network drives under Computer. Can I instead have the 'Open' click drop the users in a defined network drive or just open computer and allow them to select a share? I don't want them to see the error message. A solution that looks to have been used for Office 2000/03 is: Key: HKEY_CURRENT_USER\Software\Microsoft\Office\<version>\Outlook Value name: ForceOSTPath Value type: REG_EXPAND_SZ Value: path to your storage folder I am not sure if there is a better way to do this now OR if this even works with Office 2010.

    Read the article

  • Which events specifically cause Windows 2008 to mark a SAN volume offline?

    - by Jeremy
    I am searching for specific criteria/events that will cause Windows 2008 to mark a SAN volume as offline in disk management, even though it is connected to that SAN volume via FC or iSCSI. Microsoft states that "A dynamic disk may become Offline if it is corrupted or intermittently unavailable. A dynamic disk may also become Offline if you attempt to import a foreign (dynamic) disk and the import fails. An error icon appears on the Offline disk. Only dynamic disks display the Missing or Offline status." I am specifically wondering if, on the SAN, changing the path to the disk (such as the disk being presented to the host via a different iSCSI target IQN or a different LUN #) would cause a volume to be offlined in disk management. Thanks! Edit: I have already found two reasons why a disk might be set offline, disk signature collisions and the SAN disk policy. Bounty would be awarded to someone who can find further documented reasons related to changes in the volume's path. Disk signature collisions: http://blogs.technet.com/b/markrussinovich/archive/2011/11/08/3463572.aspx SAN disk policy: http://jeffwouters.nl/index.php/2011/06/disk-offline-with-error-the-disk-is-offline-because-of-a-policy-set-by-an-administrator/

    Read the article

  • How to grant read/write to specific user in any existent or future subdirectory of a given directory? [migrated]

    - by Samuel Rossille
    I'm a complete newbie in system administration and I'm doing this as a hobby. I host my own git repository on a VPS. Let's say my user is john. I'm using the ssh protocol to access my git repository, so my url is something like ssh://[email protected]/path/to/git/myrepo/. Root is the owner of everything that's under /path/to/git I'm attempting to give read/write access to john to everything which is under /path/to/git/myrepo I've tried both chmod and setfacl to control access, but both fail the same way: they apply rights recursively (with the right options) to all the current existing subdirectories of /path/to/git/myrepo, but as soon as a new directory is created, my user can not write in the new directory. I know that there are hooks in git that would allow me to reapply the rights after each commit, but I'm starting to think that i'm going the wrong way because this seems too complicated for a very basic purpose. Q: How should I setup my right to give rw access to john to anything under /path/to/git/myrepo and make it resilient to tree structure change ? Q2: If I should take a step back change the general approach, please tell me.

    Read the article

  • RDP problem with Vista and Windows 7 destination

    - by MadBison
    I use a server a home to host a bunch of concurrently running Hyper-V VM's with different OS's and software for testing. I have Vista on the laptop, all latest SP's and patches. The server is Server 2008 R2, fully patched. The guests are a mix of XP, Vista, Server 2008 and Windows 7. If I connect to the Win XP or Server 2008 guest using RDP, it is always good. Very quick, no speed issues. If I connect to the Vista or Win 7 guests, the response time is so slow it is unusable. Usually 6 or 8 seconds, and at times it is to long to measure! This happens from both the laptop running Vista, and the server running Server 2008 R2. Does anyone know what the issue is with RDP on Vista and Windows 7 destinations? I did read this: http://blog.tmcnet.com/blog/tom-keating/microsoft/remote-desktop-slow-problem-solved.asp and that is not the problem I have applied that change to all PC's.

    Read the article

  • Ubuntu Server attack? how to solve?

    - by saky
    Hello, Something (Someone) is sending out UDP packets sent from our whole ip range. This seems to be multicast DNS. Our server host provided this (Our IP Address is masked with XX): Jun 3 11:02:13 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 Jun 3 11:02:23 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 Jun 3 11:02:32 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 Jun 3 11:02:35 webserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:30:48:94:46:c4:08:00 SRC=193.23X.21X.XX DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53 I checked my /var/log/auth.log file and found out that someone from China (Using ip-locator) was trying to get in to the server using ssh. ... Jun 3 11:32:00 server2 sshd[28511]: Failed password for root from 202.100.108.25 port 39047 ssh2 Jun 3 11:32:08 server2 sshd[28514]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.100.108.25 user=root Jun 3 11:32:09 server2 sshd[28514]: Failed password for root from 202.100.108.25 port 39756 ssh2 Jun 3 11:32:16 server2 sshd[28516]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.100.108.25 user=root ... I have blocked that IP address using this command: sudo iptables -A INPUT -s 202.100.108.25 -j DROP However, I have no clue about the UDP multicasting, what is doing this? who is doing it? and how I can stop it? Anyone know?

    Read the article

  • Wastage of resources in Virtualization

    - by Sabeen Malik
    I have asked this question on SO, but was suggested that i ask it here on SF, so here it goes. http://stackoverflow.com/questions/3010753/wastage-of-resources-in-virtualization I am not sure if this is the right place to ask the question. However i hope it is. When looking for a VPS earlier today, I was trying to understand how each container would work in the background. Keeping in mind the fact that the operating system uses most of the memory and power on a system, wouldn't having multiple operating systems in the same machine mean more wastage of resources. For instance if i was running centOS on a dedicated box and it was running lets say 20 background OS level processes. Then i go and install a virtualization platform and install 5 more centOS virtual machines in the same system which are exactly the same as the host operating system. Doesn't this mean duplication of those 20 processes 6 times? So internally the context switching is happening between 120 processes instead of 20? Further Notes: Here is an example of what i am thinking: I have a master-slave configuration for a long running, cpu + memory intensive process, which can be distributed to 4 machines. Lets say when the process runs on these 4 machines with lets say 1 Gh CPU and 1 Gig RAM, i get 400 results per hour from the cluster (assuming 100 results from one machine) . Now i get a bigger machine ( lets say 4Gh and 4 Gig RAM), have 4 virtual hosts on it with 1 Gz CPU and 1 Gig RAM. Will this configuration give me the same 4 results per hour from these 4 virtual hosts?

    Read the article

  • "Server Unavailable" and removed permissions on .NET sites after Windows Update

    - by tags2k
    Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

    Read the article

  • pxe boot dos 7.x / 8.x on modern mainboard without floppy controller

    - by GitaarLAB
    How to pxe boot MS DOS 7.x / 8.x on a modern pc (mainboard without floppy controller) without using an external usb floppy drive? MS DOS 6.22 and earlier or other flavors pxe boot just fine on floppy-less hardware. But DOS 7.x and 8.x renders an error on boot: "Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) I read somewhere during research this was a rather unknown error, that started to become more common due to the advent of floppy-controller-less hardware. On some hardware (bios dependent) one could plug a usb-floppy-drive in the computer before booting (but that MIGHT also require it to be a "golden floppy drive" (as they where called back then). From a russian site (I read about a year ago and cannot find the hyperlink) MS-Dos versions 6.22 did some-kind of floppy-drive reset during initialization and since it couldn't connect to the floppy-host thus the error. How can I resolve this (without a physical external usb floppy)? Might there be some kind of virtual floppy-driver that could resolve this (for example to be loaded before the dos image loads)? Or could someone point me into the right direction (maybe even a hex-address and some further explanation or something)? I'm using syslinux by the way.

    Read the article

  • finding the best network latency between two countries

    - by Yoav Aner
    I know there are many tools to test for bandwidth and latency, but they all rely on having at least one host from which you can run those tests. I wonder whether there's an online source or some other way to guestimate the latency or speed between two countries (in general). For example, would a customer in Japan get lower latency if the server is located in Singapore or Australia? Is a user in India likely to get higher download speed from a server in the UK or in the US? Are there any online resources or some clever ways to answer those questions with a reasonable degree of accuracy? [UPDATE]: Thanks for the great suggestions from Raffael Luthiger. I didn't know about those looking glass servers. The submarine cable maps were also really cool to discover (Thanks to Jesper Mortensen). Also seems really wise if I could ask those network professional in the area for their experience, but obviously I don't have access to those. At least some of them are on SF :) However, I'm still a little unsure how to combine those resources to give me some measurements. This is the information I have: Two countries (A,B). I do have IP addresses of customers in country A (I can obtain those from the web server log files for example). Presumably I can find some looking glass servers in country B and run a trace to those IPs. What's the best measurements to use? Are there any scripts that help automate at least some of this process?

    Read the article

  • Apache reports a 200 status for non-existent WordPress URLs

    - by Jonah Bishop
    The WordPress .htaccess generally has the following rewrite rules: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> When I access a non-existent URL at my website, this rewrite rule gets hit, redirects to index.php, and serves up my custom 404.php template file. The status code that gets sent back to the client is the correct 404, as shown in this HTTP Live Headers output example: http://www.borngeek.com/nothere/ GET /nothere/ HTTP/1.1 Host: www.borngeek.com {...} HTTP/1.1 404 Not Found However, Apache reports the entire exchange with a 200 status code in my server log, as shown here in a log snippet (trimmed for simplicity): {...} "GET /nothere/ HTTP/1.1" 200 2155 "-" {...} This makes some sense to me, seeing as the original request was redirected to page that exists (index.php). Is there a way to force Apache to report the exchange as a 404? My problem is that bogus requests coming from Bad Guys show up as "successful requests" in the various server statistics software I use (AWStats, Analog, etc). I'd love to have them show up on the Apache side as 404s so that they get filtered out from the stat reports that get generated. I tried adding the following line to my .htaccess, but it had no effect (I'm guessing for the same reason as the previous redirect rules): ErrorDocument 404 /index.php?error=404 Does anyone have a clever way to fix this annoyance? Additional Info: OS is Debian 6.0.4, and Apache version looks to be 2.2.22-3 (hosted on DreamHost) The 404 being sent back to the client is being set by WordPress (i.e. I'm not manually calling header() anywhere)

    Read the article

  • Hotmail marking messages as junk

    - by Canadaka
    I was having problems with emails sent from my server being blocked completely by Hotmail, but I found out Hotmail had blocked my IP and by contacting Hotmail I had the block removed. See this question for more info: Email sent from server with rDNS & SPF being blocked by Hotmail But now all emails from my server are going directly to recipients "Junk" folder on hotmail and I can't figure out why. Hotmail says "Microsoft SmartScreen marked this message as junk and we'll delete it after ten days." I tried contacting the same people at Hotmail who had my IP block removed, but I haven't received any reply and its been almost a week. Here are some details: I have a valid SPF record for my domain "v=spf1 a include:_spf.google.com ~all" I have reverse DNS setup I have a Sender Score of 100 https://www.senderscore.org/lookup.php?lookup=66.199.162.177&ipLookup.x=55&ipLookup.y=14 I have signed up for Microsoft's SNDS and was approved. My ip says "All of the specified IPs have normal status." Microsoft added my IP to the JMRP Database My IP is not on any credible spam lists http://www.anti-abuse.org/multi-rbl-check-results/?host=66.199.162.177 my FROM header is being sent in proper format "From: CKA <[email protected]>" Here is a test email source:

    Read the article

  • ssl port didnt work on nginx

    - by Jin Lin
    I set up the unicorn and nginx on one of my ec2 machine. and my request are loading ok with nginx listen to port 80. but when I enable it to ssl, which listen to port 443. It doesn't work. and it can still work with port 80, https. server { listen 443 ssl; # replace with your domain name server_name domain.com; # replace this with your static Sinatra app files, root + public root /home/ubuntu/domain/public; ssl on; ssl_certificate /etc/ssl/domain.crt; ssl_certificate_key /etc/ssl/domain.key; # maximum accepted body size of client request client_max_body_size 4G; # the server will close connections after this time keepalive_timeout 5; location ~ ^/assets/ { add_header ETag ""; gzip_static on; expires max; add_header Cache-Control public; } location / { proxy_set_header X-Forwarded-Proto https; try_files $uri @app; } location @app { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; # pass to the upstream unicorn server mentioned above proxy_pass http://unicorn_server; } }

    Read the article

< Previous Page | 439 440 441 442 443 444 445 446 447 448 449 450  | Next Page >