Search Results

Search found 14772 results on 591 pages for 'full trust'.

Page 446/591 | < Previous Page | 442 443 444 445 446 447 448 449 450 451 452 453  | Next Page >

• My PC is powercycling, what's going wrong?

  - by Renai

  So here is my sorry story of woe. My PC has been functioning normally for some time. Last week I bought a cheapish powered USB hub and plugged it into my home PC, which runs Windows 7. This weekend I plugged that hub into my home PC. At some stage I hibernated the PC. Then later on I plugged my Kobo eReader into the hub to charge. Later on I started the PC up. Only thing is, it now won’t start up. It just powercycles on for a second and a half with the fans at full, then powercycles off. Then back on for two seconds, then back off. There’s no display at all and it won’t get to the BIOS screen. It looks like anything USB is not functioning — the keyboard and mouse are not lighting up etc. I’ve taken out the BIOS battery and reseated the RAM, reseated the graphics card and so on, but my suspicion is that I have blown the USB section of the motherboard somehow. Suggestions? All else failing, where is the best place to take this machine in Sydney to get evaluated? It’s a fairly powerful beast, all up has cost me about $2500 over the years, including upgrades and a recent new graphics card, so can’t just start from scratch.

  Read the article

• Daisy-chainable DisplayPort Monitors

  - by thepurplepixel

  I am the proud new owner of a MacBook Pro with a mini-DisplayPort. My desk setup used to allow me to position the screen of my old MacBook beside an external monitor, essentially allowing dual-head. It was also advantageous that my old MBP and my external monitor had the same resolution, 1440x900. Now, I'm searching for a set of two monitors that I can use a HengeDock with. Unfortunately, the MacBook Pro suffers from having only one mini-DisplayPort. Looking up the spec for DisplayPort 1.2 (which the MBP supports), DisplayPort daisy chaining is supported. What I'm looking for is a monitor that has two DisplayPorts so I can daisy chain two monitors off the single mini-DisplayPort. What I don't want is a USB-based video solution. I need full acceleration on both monitors; an external video card won't cut it. I hope I don't have to wait a few years for these monitors to come out. TL;DR: I need two monitors with two DisplayPorts each that I can daisy-chain. Thanks!

  Read the article

• Do eSATA HDD docking stations have a capacity limit?

  - by Michael Kjörling

  I'm looking at perhaps buying an eSATA docking station to be able to easily plug in and unplug hard disk drives, particularly but not necessarily only for backup purposes. Note: This is not a hardware shopping recommendation question. Please don't vote to close it as such. Looking at different models, I find for example this page detailing the Deltaco SI-7908SUS which specifically states "storage capacity: 1.5 TB" as well as "pictured hard disk not included, only for illustration". A customer review specifically mentions that it does not work with 3 TB drives, although does not go into any detail such as OS, drive model, etc. From a brief glance, the vendor's web site does not appear to say either way. Then there is the quite similar Deltaco SI-7908B3 which boasts on the box "all 2.5" and 3.5" HDD/SSD compatible". My question is: Why would what basically amounts to a SATA/eSATA adapter have any say in what storage capacity devices are supported? Does it? Assuming the OS supports the full capacity of the drive, why should introducing another (not even a different, really) connector change anything? Bonus question: Might it make a difference if the docking station exposes multiple interfaces (such as in the case of for example the SI-7908SUS exposing USB 2.0 and eSATA)? (I still think it shouldn't, but it'd be nice to have it confirmed.)

  Read the article

• Problem in accessing Windows shared folder on Ubuntu using terminal

  - by vikramtheone

  Hi Guys, Description I have 2 systems with me, one running on Windows(Host) and one on Ubuntu, both on a LAN. On the Windows(Host) I develop software intended for the Linux system and because the Linux system has little external memory, my idea to overcome this is by making the project folder on the Host side a Shared Folder with full access and access it on Ubuntu over the network. To achieve this, I have installed Samba on Ubuntu, when I go to Places -> Network I can see the shared project folder and I simply mount it. A link appears on the desktop. Next, using Nautilus I open the link and I can access the contents of the shared folder. Problem Even though I mount the shared project folder, I don't see it appearing in the /media or the /mnt folder, as a result of this I don't know what path to use to access this folder, from the terminal. For example: When, I mounted my USB stick, as expected, a link for the device appears on the Desktop and I also see a folder in the media folder. So, similarly, a mounted shared folder should have appeared on the /mnt folder, too. Can anyone suggest what I should do now? There are many posts around, but no solid solution for this problem. Help!!! :) Vikram

  Read the article

• Windows Phone sync error when syncing with iTunes on different Hard Drive

  - by njallam

  I have my iTunes library file on a separate hard drive (which I believe may be the cause of the problem) and I have been trying to use it to synchronize with my Windows Phone. I would like to first note that if I set up my phone to synchronize with 'Windows Libraries', then it works fine. This is however not ideal as I have categorised my music and made playlists etc, on iTunes. When I first link my Windows Phone to the Windows Phone App (for desktop) and select iTunes from the above selection, I get the following error message: After searching that error, I found the following forum threads: Fix for error 8300300B when trying to sync Lumia 920 Windows 8 Phone in PC? Error code 8300300B on Windows Phone 8 while trying to sync I've tried the workarounds described in the above threads, however, they did not work for me. If I ignore that error message, I see the expected interface, along with all of my iTunes library's media, however the 'Sync' button is greyed out. I have tried some other things to try and fix this: Removing the app's AppData folder Uninstalling, reinstalling Using the full-screen modern app (does not allow for iTunes syncing)

  Read the article

• Auto Log-Off Windows users - Windows 2003 domain

  - by thehatter

  Hi! I am trying to make windows clients automatically log off after some time, I have been trying to use the winexit.scr which I have seen working else where in a similar environment. After working though these instructions (I did read the comments and notice the original ADM provided is buggy) I've had no joy what so ever! Winexit.scr refuses to read any settings in the registry, even while using a test account I can access the required reg key(s); edit, add, and remove values. Essentially winexit.scr always uses it's default values: 30 second timeout, no forced log-out. What I really want is a 30 minute timeout with a forced log-out, closing all the users apps etc. I've tried removing and re-adding the ADM template, creating the GPO from scratch several times, giving various registry permissions - including full control to "Everybody" just for fun! Oh, clients are all win XP SP3, DC is win 2003 R2 SP2. So, can anybody suggest something? Cheers!

  Read the article

• VCL - configuration for Magento and Varnish 3.0.2

  - by Tomas

  I would like to kindly ask if there's someone who can help me configure Varnish for Magento to reach far more hits. My current ratio from varnishstat is: cache_hit=271 cache_miss=926 I'm kindly asking this because I've googled almost every site related to this theme, but 99.9% of configurations don't work because of outdated code. Details of my set-up: I use Varnish on port 80, Apache on port 81, PageCache as Magento varnish module, APC for PHP speed and Memcached for dynamic caching. Load speed is about 1.5s on home-page (Pingdom.com average results) USA ping & 2.5s Europe. Servers are located in Toronto, Canada. EDIT: This is my full VCL configuration http://pastebin.com/885BzHCs (I just use xxx.xxx.xxx.xxx for my IPs) This is the info from the command (varnishtop -i TxHeader -I Cookie): TxHeader Cookie: frontend=965b5...(*lots of numbers); adminhtml=3ae65...(*lots of numbers); EXTERNAL_NO_CACHE=1 "(*lots of numbers)" is just my adding to the info Any idea how to avoid Varnish hitting this cookies? (If I got correctly the idea about avoiding Vanrish hitting the cookie and not caching the home page). Thank you for any help!

  Read the article

• Why do hosts prefer Linux to Windows Server?

  - by iconiK

  So far I see a HUGE majority of hosts provide only Linux shared hosting, providing Windows only to VPS (or even to only dedicated servers). Why is it so? While Windows is a lot more expensive than Linux (though it depends on a lot of factors, not just initial and support license cost), it also provides ASP.NET, IIS and of course, Microsoft SQL Server. I know in the past it might have been because of cPanel being Linux only but now they have a Windows version. But still, why is Linux predominantly used on shared hosting? PHP works on both systems. IIS can be (and probably is) faster. MySQL runs on both systems as well. cPanel has a Windows version. Python, Perl, Ruby, all run on Windows as well. You even have MS SQL Server Express, which I find more superior than MySQL in both speed and features. Access is there for low usage requirements, as is SQLite (which is so great for quick small stuff). And with PowerShell you have a good alternative to the Unix shell. EDIT: I am looking for common reasons, I realize each hosting company (and/or it's clients) may have different needs. This becomes very important when you get to VPS or Cloud which give you a full operating system to use.

  Read the article

• Outlook 2010 not resolving SMTP address to Display Name

  - by Ben

  I have a weird problem where a user (director, naturally) has an odd problem with the way the to field shows in his Outlook. We are using Outlook 2010 (with RPC/HTTP) and Exch 2003 at the back end. Most of his mail shows in his mailbox with the To: field as normal. (e.g. Fred Bloggs in the to field.) However, some mails come in showing in the To: field as [email protected]. (Apparently this is an issue!) For example, most show as: but a few come in as: There doesn't appear to be a pattern to this. I have tried to replicate by: Sending from any specific senders to see if it recurs (it doesn't) Typing his full name in my Outlook and sending (it resolves as normal) Sending programatically (e.g. from script) - (it still resolves OK) Forcing a "[email protected]" entry in my Outlook. It resolves as soon as I hit enter Sending in cached mode Sending disconnected Anyone got any ideas how I can either replicate the problem or fix it! I can't tell at the moment whether it is a problem at his end or the sender's. EDIT This seems to be a global issue, following some more digging. Most people seem to have a few emails in their inbox addressed to their smtp address, rather than display name.

  Read the article

• How can I wipe my iPod classic and fix any bad sectors on the hard drive without killing it?

  - by Sam Meldrum

  My iPod never finishes syncing and only syncs audio, not pictures or video. Any ideas as to how I can fix it? My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated? Update I have eliminated problems with the files, PC or iTunes as they sync fine to other iPods. I have also eliminated the cable by trying different cables which work with other iPods. What I'd really like to know is if there is any way to more fundamentally wipe the iPod safely, attempt to repair any bad sectors on the hard drive and then start from scratch. Anyone ever managed this?

  Read the article

• Performance data collection for short-running, ephemeral servers

  - by ErikA

  We're building a medical image processing software stack, currently hosted on various AWS resources. As part of this application, we have a handful of long-running servers (database, load balancers, web application, etc.). Collecting performance data on those servers is quite simple - my go-to- recipe of Nagios (for monitoring/notifications) and Munin (for collection of performance data and displaying trends) will work just fine. However - as part of this application, we are constantly starting up and terminating compute instances on EC2. In typical usage, these compute instances start up, configure themselves, receive a job from a message queue, and then get to work processing that job, which takes anywhere from 15 minutes to over 8 hours. After job completion, these instances get terminated, never to be heard from again. What is a decent strategy for collecting performance data on these short-lived instances? I don't necessarily need monitoring on them - if they fail for whatever reason, our application will detect this and handle re-starting the job on another instance or raising the flag so an administrator can take a look at things. However, it still would be useful to collect information like CPU (user, idle, iowait, etc.), memory usage, network traffic, disk read/write data, etc. In our internal database, we track the instance ID of the machine that runs each job, and it would be quite helpful to be able to look up performance data for a specific instance ID for troubleshooting and profiling. Munin doesn't seem like a great candidate, as it requires maintaining a list of munin nodes in a text file - far from ideal for an environment with a high amount of churn, and for the short amount of time each node will be running, I'd rather keep the full-resolution data indefinitely than have RRD water down the data over time. In the end, my guess is that this will require a monitoring engine that: uses a database (MySQL, SQLite, etc.) for configuration and data storage exposes an API for adding/removing hosts and services Are there other things I should be thinking about when evaluating options? Perhaps I'm over-thinking this, though, and just ought to run sar at 1-minute intervals on these short-lived instances and collect the sar db files prior to termination.

  Read the article

• WAMP starts Apache or Mysql, but not both?

  - by ladenedge

  When I install WAMP, the Apache and Mysql services are set to run as the LocalService user and all works well. However, because I need to access remote UNC paths in my PHP code, I need to run at least Apache as a user that exists on both the local host and the remote host - I'll call him WampUser. When both Apache and Mysql are set to start as WampUser, I cannot start both at the same time. If both are stopped, I can start either successfully. When I attempt to start the other, I get Error 1053: The service did not respond to the start or control request in a timely fashion. This error appears immediately - there is no timeout. When at least one of the services is set to start as LocalService, both start fine. I can, therefore, solve my problem by setting Apache to WampUser and Mysql to LocalService, but I'm more interested in why this is happening in the first place. I'm especially curious because this situation does not occur on other servers - something I've done to this server has made these two services exclusive when running as the same user. Here are some miscellaneous data points: I am using Windows Server 2003. I've provided recursive Full Control to the C:\wamp directory for WampUser. Nothing appears in the event log after the service fails. No log entries appear in either the Mysql log or the Apache error log. Neither application appears in the process list when the appropriate service is stopped. Any ideas?

  Read the article

• (manually configured) kernel update leaves wireless in a mess

  - by Mala

  I recently upgraded my kernel from 2.6.31-gentoo-r6 to 2.6.32-gentoo-r7. In both cases, I configured everything manually. However, since the upgrade, my wireless card appears to be on the fritz. It will connect to networks just fine, and remain connected, but can only access the internet (and other hosts on the network) for about 3 seconds after connecting. Reconnecting to the network appears to fix the problem... for another 3 seconds or so. The problem is "solved" by booting into the older kernel. The relevant lspci entry is 02:00.0 Network controller: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection I'm pretty sure I have the correct drivers enabled in the kernel Device Drivers ---> Network device support ---> Wireless LAN (IEEE 802.11) ---> <*> Intel Wireless Wifi [*] Enable LED support in iwlagn and iwl3945 drivers [*] Enable Spectrum Measurement in iwlagn driver [*] Enable full debugging output in iwlagn and iwl3945 drivers <*> Intel Wireless WiFi Next Gen AGN (iwlagn) [*] Intel Wireless WiFi 4965AGN [*] Intel Wireless WiFi 5000AGN; Intel WiFi Link 1000, 6000, and 6050 Series I tried with the other intel drivers enabled as well (iwl3945) and no difference. Is there something stupid I'm missing? Is there something I have to recompile after upgrading the kernel (a la nvidia)? Thanks Mala

  Read the article

• Netflix streaming stops loading at 98% on Revo 3700

  - by Martin Harris

  I'm trying to stream Netflix on an Acer Revo 3700 running Windows 7 Home Premium, but it hangs on the loading screen at 98% (after it has formatted the player to the right aspect ratio and added the controls, but before the video starts) with no error messages or failures. I have two other machines on the same network, one running Windows 7 Home Premium and another running XP, which both stream faultlessly. Things I have tried: Both a wired and wireless connection to the router Upgrading the video and audio drivers IE, Chrome and Firefox Boxee software Connecting with a VGA cable instead of HDMI (in case it is a HDCP thing) Uninstalling and reinstalling Silverlight. Getting someway into loading a HD movie and turning "Allow HD" off Does anyone know what Netflix is doing at the 98% load mark? Are there any log files? Anything else worth trying? Full disclosure: I'm using Netflix from the UK through a US based VPN. I've tried multiple VPNs and the problem is exactly the same, also the other machines on the same network through the same VPN work fine so I don't think this is the issue, but it might be a factor. The region check happens at around 7% and I get past that.

  Read the article

• What options to use for Accurate bacula backup ?

  - by Kiss Stefan

  It's actually 2 question in one. First is a bit more theoretically. So when specifying accurate options how does bacula figure out if a file needs to be backed up ? it's a simple AND ? As in if the options are Accurate = sm5 bacula will not backup the file if ((size = old size) AND (modtime = old modtime) AND (md5 = old md5)) Is that correct ? Do any of the options take precedence ? as in would be a file skipped if modif time is diffreent but it has the same md5sum ? Are there any implied options that you cannot ignore ? Practical case, ( bacula 5.0.1 ) I have to back-up a svn repo, in order to be able to make incremental backups as simple as posible i am hotcopying (client run before) it to another location, that bacula will backup ( then delete it with client run after). Now in the fileset i have Accurate = spnd5 This should tell bacula to take into consideration size , permission bits number of links , decreases in size and md5sum. However , an incremental is also including a full copy of the svn. What am i doing wrong ? it seems that it takes into account creation time even tho i have not specified it.

  Read the article

• Certificate enrollment request chain not trusted

  - by makerofthings7

  I am working on a MSFT lab for Direct Access, and need to create a Web certificate. The instructions ask be to do the following: On EDGE1, click Start, type mmc, and then press ENTER. Click Yes at the User Account Control prompt. Click File, and then click Add/Remove Snap-ins. Click Certificates, click Add, click Computer account, click Next, select Local computer, click Finish, and then click OK. In the console tree of the Certificates snap-in, open Certificates (Local Computer)\Personal\Certificates. Right-click Certificates, point to All Tasks, and then click Request New Certificate. Click Next twice. On the Request Certificates page, click Web Server, and then click More information is required to enroll for this certificate. On the Subject tab of the Certificate Properties dialog box, in Subject name, for Type, select Common Name. In Value, type edge1.contoso.com, and then click Add. Click OK, click Enroll, and then click Finish. In the details pane of the Certificates snap-in, verify that a new certificate with the name edge1.contoso.com was enrolled with Intended Purposes of Server Authentication. Right-click the certificate, and then click Properties. In Friendly Name, type IP-HTTPS Certificate, and then click OK. Close the console window. If you are prompted to save settings, click No. In production, our company has overridden the Web Server template and it doesn't seem to be issuing certificates with the full CA chain. When I look at the issued certificate properties then both tiers of the 2 tier CA hierarchy are missing. How can I fix this? I'm not sure where to look outside the GUI.

  Read the article

• Move the uploads folder in Wordpress

  - by Victor Hurdugaci

  Currently, my Wordpress' upload folder is located in \wp-content\uploads. Initially there was no structure so all files were put there. After a while it was changed to upload the files in \wp-content\uploads\YEAR\MONTH. Now that folder contains a mix of files (those starting with + are folders) like: +wp-content | +2010 | | +02 | | | File-1 | | | File-2 | | | .. | | | File-n | | +01 | | | File-1 | | | File-2 | | | .. | | | File-n | +2009 | | +12 | | | File-1 | | | File-2 | | | .. | | | File-n | | +11 | | | File-1 | | | File-2 | | | .. | | | File-n | +.. | | | .. | Unstructured-file-1 | Unstructured-file-2 | ... | Unstructured-file-n Based on the dates of the unstructured files, I would like to move them in a structured hierarchy (based on date, move it to a folder \wp-content\uploads\YEAR\MONTH). Now, my questions are: Where do I write and execute a script to the movement (I don't have full access to the server, just to a cPanel and to the Wordpress Admin page)? What must be updated so that the links in posts, that reference the unstructured files, point to the new location of those files? Not fully related to the previous description: is it alright to move the whole uploads folder to another location, like \uploads? PS: Moving the files/updating the database manually is not an option :)

  Read the article

• How to serve media across home network?

  - by TK Kocheran

  I'm looking to share my media across my home network. Router fully supports running a DLNA server, but I don't know if it'd be better to run the server from my main server computer instead of from the router, as the router would have to operate off of a network share and my server can operate directly off of the files. Here's what I need to serve, in order of importance: ISO 1:1 DVD rips (4-8GB files), MP4/H.264 encoded videos, MKV videos, MP3 files, JPEG/CR2 images. Maybe I'm completely ludicrous for wanting to push full DVD files across my network, but in reality, I would assume that only the parts of the actual file needed (ie: menu, main video payload for main title) would be served at any one time. Plus, encoding takes time and precious disk space, so why not stream it 1:1 ;) Does anyone know of the best way to accomplish this? Main goal is to serve it to Logitech Revue downstairs and secondary goal is to serve it to other computers in the house. For music, I assume I could run a DAAP server, but I don't think that the Revue supports that (and I can't exactly throw together an app that does it just yet).

  Read the article

• How to setup a hyper-v domain with internet access

  - by fynnbob

  First off let me say that I'm not a network admin or server guy, I know very little about that stuff. What I'm trying to do is setup a virtualized domain using hyper-V. Here is the configuration: Physical Server: 4Mb RAM Windows Server 2008 R2 running Hyper-V Virtual Environment: One Domain Controller running Windows Server 2008 R2 One Client running Windows Server 2008 R2 I have been successful in setting up a virtual domain controller and adding a virtual client to that domain controller but I'm stuck at trying to give the virtual Environment Internet access. I can give the client VM Internet access if I remove them from the virtual domain but once I add them back to the virtual domain, Internet access is gone. I've read articles describing many different ways this can be done (using RRAS with NAT, using a wireless connection, etc...) but all of those articles only cover a small piece of the setup and also seem to be geared towards people who know there way around networking and servers which I don't. I'd like to know more but my thing is software development and I have my hands full trying to keep up with everything in that realm. I simply want to setup a virtual domain with Internet access for testing. Can anyone point me to any "for Dummy's" type information on how to setup this type of environment or can anyone provide this kind of step-by-step help. Any help would be very much appreciated.

  Read the article

• Windows7 corrupted profile - prevention exists?

  - by Radek

  I have dedicated Windows7 (not on domain) virtual machine for overnight automation testing. Some commands (mySQLdump, tscon.exe) must be run under administrator account. Last week administrator account's profile was corrupted. I fixed it by renaming it in the registry and logging in as administrator. And today it is corrupted again. I use administrator account only to run above commands via runas. Also the computer is restarted via cmd - shutdown command - quite often. Especially every night before automation testing starts. I checked the comp for viruses - did full scan using avast although I believed that the comp is clean. Any idea how to prevent the profile to get corrupted again? update So the first log entry in event log is today from 1.15am and one of my scripts ran runas command as administrator exactly at 1.15am. It was second time that runas war executed though after the testing started. The same happened second day in a row. Before the testing starts I need to copy one file that is locked. So I run handle.exe from runas to unlock it. That is what I think causing the profile to get corrupted. I am not able to reproduce it by myself. The message from event viewer is Windows cannot load the locally stored profile. Possible causes of this error include insufficient security rights or a corrupt local profile. DETAIL – The process cannot access the file because it is being used by another process.

  Read the article

• UAC being turned off every time Windows 7 starts

  - by Mehper C. Palavuzlar

  I have strange problem on my HP laptop. This began to happen recently. Whenever I start my machine, Windows 7 Action Center displays the following warning: You need to restart your computer for UAC to be turned off. I never disable UAC, but obviously some process or virus (I'm not sure, only guessing) causes this. As soon as I get this warning, I head for the UAC settings, and re-enable UAC to dismiss this warning. This is a bothersome situation as I really don't know what causes the problem. I have run a full scan on the computer for any probable virus activity, but TrendMicro OfficeScan said that no viruses have been found. Malwarebytes' Anti-malware could not find any malicious items either. There are no other strange incidents on the machine. Everthing works fine except this bizarre incident. How can I learn what process is trying to turn off UAC? What way should I follow to overcome this problem?

  Read the article

• HP Laserjet 1320 drivers for Windows 7

  - by RedGrittyBrick

  Background I replaced som XP computers with Win 7 computers. We have a HP Laserjet 1320dn printer attached to the LAN. The XP computers could print to it from Word in duplex mode without any issues. Problem The Win 7 computers downloaded a full set of drivers including a "HP Laserjet 1320 PCL5" driver. However using this, Word's page footers cause extra pages to be printed with just a letter or so at a time from the footer. Some other apps have similar issues. I also have an ancient Laserjet 1200 attached to the LAN via a Jetdirect box and that works just fine. So I don't think the problem is with Word (the computers came with Word 2010 starter). What I tried I wrangled the control-panel new printer dialogue into using a "HP Laserjet 2100 PS" driver for the HP Laserjet 1320dn. Now my Word documents print as they should. However I don't have a duplex option on the print dialogue. I'd really like to be able to use duplex printing. Question Windows used to have a Universal Postscript driver that read a Postscript Printer Definition (PPD) file to make the printer's features available (tray choice, duplex etc). I can't see any way to do this in Windows 7. Is there a way? Is there any other way I can get Windows 7 Home Premium 64-bit to print properly to a HP Laserjet 1320dn and have access to all it's major features? Addendum: My page in Word looks like this: +--------------------+ | aa bb cc | | | | lorem ipsum dolor | | | ... | | | pp qq rr | +--------------------+ The headers and footers were inserted using Insert - header - blank (3 column). When printed I get 1 page with aa, bb, cc, pp in correct position (no other text) 1 blank page 1 page with qq in correct position (no other text) 1 blank page 1 page with rr in correct position (no other text) 1 blank page 1 page with lorem ipsum dolor in correct position (no headers or footers) If I use a Laserjet 2100 driver I get 1 correct page.

  Read the article

• Printing from Firefox on different printers and setting the page details beforehand

  - by user1162541

  I´ve got an odd problem and I have not been able to fix this. I have a computer which is connected to two printers. One is a receipt printer (EPSON TM-U220), and the other one is an impact printer (Epson LX-300+). From Firefox, I need to print on both printers at different moments. So first I print on the receipt printer, then on the impact printer, etc. However, whenever I first print on the receipt printer, and then go back to the impact printer, the printout is only the width of the page of the receipt printer. That is, the page does not come out properly, just the left part of the page is used for printing and the right part is completely empty, as if I am just printing on the small receipt paper. And there is no way I can tell Firefox that I am printing on this larger printer. The second print on the impact printer goes fine. Firefox now knows it is printing on the impact printer, and it comes out properly on the full page width. But every first print on the impact printer is using the wrong paper size. How can I fix this? When I go to PAGE PREVIEW I can not set the printer UNTIL I actually print the page. If I go to PRINT PREVIEW CONFIGURE PAGE, I can not set the printer I will be using. I can only do so if I go to PRINT PREVIEW PRINT (here is the dropdown box to set the printer). But I can only set the printer and then click PRINT, or CANCEL. If I click PRINT, then the computer remembers the setting but that page will come our wrong, and when I click cancel it simply does not remember the printer I just set.

  Read the article

• Cannot delete flash9.ocx

  - by Kara Marfia

  Some kinda voodoo, indeed. Bought a new boot drive, and it's time to use the old drive for data. I thought I'd save some time by just wiping the unneeded system folders, instead of backing up, formatting, and restoring. Wups! I have a single Adobe file that absolutely will not be deleted. G:\Windows\SysWOW64\Macromed\Flash\flash9.ocx - though it may have started with a different file name. I'm able to rename it, oddly enough. To be clear, the drive is currently plugged in externally. So I can boot the computer, plug this drive in afterward, and immediately attempt to delete. "File in use" box reads "the action can't be completed because the file is open in another program". I'd format at this point, but it's my white whale, and I have to know if Adobe has inserted some nasty little registry hack - or whatever it is - making this impossible. Since I'm sure it'll come up, I've taken ownership of the file - and this was the trick preventing me from deleting anything else on the drive - full rights on the file permissions, you name it, I've fiddled with the file itself. I'm about to try uninstalling flash from the system drive, in case that aligns the planets properly. Sometimes I wish I were less stubborn, and could just format already.

  Read the article

• Windows 8 x64 with VMWare Workstation or inside ESXi

  - by Dommer

  I need to run several virtual machines on a core i7-920 box with 12GB or RAM and a 256GB SSD to host the VMs. It also has a Highpoint RocketRaid 2720SGL RAID controller with a 12TB RAID 5 array. I want one of my VMs to run Windows 8 x64, to have access to the RAID array as a native disk (not as networked drives and it needs to run at full speed) and to be able to send files quickly across the network. Initially I thought I'd try to do this using ESXi 5, but I have been unable to find any working RAID drivers for the RR2720SGL and it is not on the HCL for ESXi 5. In light of this, I have installed Windows 8 x64 on the hardware and am thinking of installing VMWare Workstation and running my VMs inside there. I guess my questions are these: How does VMWare Workstation 9 perform compared to ESXi 5? In the real world I mean? Presumably installing Win 8 as the host OS will give me way better performance for that Win 8 machine than Win 8 running under ESXi? I should stick with Windows 8 x64 as the host OS, right? If I install a domain controller VM inside my Win 8 box and join the Win 8 machine to that domain, am I insane (I would guess the Win 8 machine wouldn't see the domain controller until it finished starting everything up, but I don't think that matters)?! is it feasible to give metrics like this and if so, what is the likely value of x? 25%? 50%? 75%? Win 8 under ESXi runs x% as fast as Win 8 installed bare metal.

  Read the article

< Previous Page | 442 443 444 445 446 447 448 449 450 451 452 453  | Next Page >