Search Results

Search found 20556 results on 823 pages for 'image viewer'.

Page 447/823 | < Previous Page | 443 444 445 446 447 448 449 450 451 452 453 454  | Next Page >

• How tot track which program causes my harddrive to spin up

  - by Andreas

  I have a strange problem: Every half hour one of my hard disks gets powered on again. I recognize this by the sound of a hard disk spinning up. So far I was not able to track which program could cause this. I ran Process Monitor to see whether there is an I/O peak coinciding with the spin-up. I checked Windows event viewer if there is an appropriate event at the same time Any ideas other than the usual disabling-services/programs etc. (which would be my next investigation step)? Also, it would be helpful to have a program that shows the current power status of all my drives, if there is one. Harddisk Sentinel unfortunately cannot do the job because it powers on all drives upon start and prevents their going into sleep mode. Thanks in advance. :)

  Read the article

• WebDAV "PROPFIND" exception in IIS due to network share?

  - by jacko

  Hi all, We're finding continuous exceptions in our event viewer on our live box to the following exception: [snippet] Process information: Process ID: 3916 Process name: w3wp.exe Account name: NT AUTHORITY\NETWORK SERVICE Exception information: Exception type: HttpException Exception message: Path 'PROPFIND' is forbidden. Thread information: Thread ID: 14 Thread account name: OURDOMAIN\Account Is impersonating: True Stack trace: at System.Web.HttpMethodNotAllowedHandler.ProcessRequest(HttpContext context) at System.Web.HttpApplication.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) Other Specs: Windows Server 2003 R2 & IIS 6.0 We've narrowed it down to occuring when people try to access shares on the box from within the network, and have discovered (we think) that its due to the WebDAV web services extension being previously disabled by past staff. The exceptions are being thrown when trying to access directories that are virtual dirs in IIS, and plain old UNC network shares What the implications for enabling the WebDAV extensions on our live web server? And will this solve our problems with the exceptions in our event log?

  Read the article

• How does RAM fail?

  - by ethanlee16

  I have an issue with a Dell Inspiron 15 (1545) laptop that refuses to open any applications (save select Microsoft programs, e.g. Security Essentials, Ctrl Panel, Windows Explorer (not Internet), regedit, Event Viewer, etc.). I've run Microsoft Memory Diagnostics Tool and it found a 'hardware problem was detected.' Does this indicate that the RAM has failed? I notice when I open programs like Word, Excel, Internet Explorer, etc., it always give me an error from WerFault.exe saying The instruction at xxxxxxx referenced memory at xxxxxxxxx. The memory could not be written. and sometimes something about illegal instructions. If it is a hardware problem, does this mean that replacing the RAM is my only option? Again, I would also like to know if RAM can fail (like hard drives) and if malware can cause RAM to fail also.

  Read the article

• How to install service packs onto Thin Apps and other questions

  - by Buzlightyear

  I have a VM that I use to do all my ThinApps, Once I have done my application and its built I copy just the bin folder to a server which has a share, I then create a shortcut to the program exe on users desktops. This all seems to work ok. Firstly is this correct? If so, how then do I apply a service pack to that application after the ThinApp VM has been reverted to a base image, I have corel draw which i have a service pack for but it wont intall it as its saying it cant find the package installed on the computer. I have Thinreg batch file so have included corel into that and the program appears in the program list. I have the sandbox redirected to the server share mentioned earlier into seperate user folders when the user logs in. Obvisouly once i have done a App I revert to a previous snapshop so my thinapp vm is back to base image, so the corel install is lost. Sorry if im missing something very simple. Is its a case if you have an exe/msp you have to reinstall the whole app again and start over, Thanks for any help.

  Read the article

• IIS won't start

  - by doekman

  When I startup my computer, pages from my local webserver (IIS) won't load. In the event viewer(System log) I get the error below. The only way I get IIS to work again is to issue an iisreset.exe. I have Windows XP. Any ideas to fix this? Event Type: Warning Event Source: W3SVC Event Category: None Event ID: 36 Date: 27-4-2010 Time: 10:30:47 User: N/A Computer: NLD4P4Z2J Description: The server failed to load application '/LM/W3SVC'. The error was '8007045b'. For additional information specific to this message please visit the Microsoft Online Support site located at: http://www.microsoft.com/contentredirect.asp. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• Why did windows change the elevation requirements of my AutoHotKey script, and how can I prevent such in the future?

  - by monsto

  I was working on an AutoHotKey (AHK) script to create prefab mouse movements for a very simple model viewer. I worked on it for a good hour. I zipped the script, posted it to a forum, and thought "oh hey, I should add bla bla bla to the script". When I returned to the program, the AHK script would not work. I could see the mouse movements working in other programs (notepad, chrome, etc), but not where I had been working the previous hour. After several hours of throwing darts at the troubleshooting wall, I discovered that the fix was to set the AHK.exe to Run as Administrator. The question here are multiple Why did Windows 7, in all it's wisdom, suddenly decide that elevation was necessary in the middle of usage? Can these permission requirements somehow be reverted by, say, removing a key from the registry or something? How can this kind of Windows behaviour be avoided in the future?

  Read the article

• BIOS corrupted? How to proceed? Acer Travelmate 290

  - by dtlussier

  I have a older ACER Travelmate 290 (manufactured in 2002 or 2003), which I recently tried to upgrade to Ubuntu 9.10. After doing the upgrade process it appeared as if I had a problem with my x server configuration, as on the first reboot post-install I heard the Ubuntu startup sound, but had a black screen. I thought I would then reboot again to drop down into text-mode to trouble shoot the x configuration problem. However, when I tried rebooting, something went wrong and since then when I start up the machine I get absolutely nothing except the first hardware check (i.e. HDD light flashes, CD/DVD drive spins, etc.). Other than that the screen remains totally black and I have no HDD or processor activity at all. I have tried restarting it a number of time holding down all kinds of key combinations to try and coax it into the BIOS (if possible) with no luck. I have also tried putting in both a live Linux disc and a Windows install disk without any luck. With a disk in the drive it will spin for a few seconds and then stop. All this has lead me to suspect that the BIOS is somehow corrupt (not sure about the right terminology). I have tried putting a new BIOS image and installer program downloaded from ACER on a USB key to see if it will run when I start up the machine, but no luck. I'm not sure if this method of interacting/updating/flashing the BIOS will work outside of Windows/DOS as both OSs are mentioned kind of ambiguously in the documentation. I have also taken the laptop case apart and inspected the various cards and cannot find any obviously burned out components. I'm not sure how to proceed at this point in terms of components to try, or how to try and load a new BIOS image onto the board. Any advice here would be great, especially from those with experience with this particular line of laptops. Thanks!

  Read the article

• Increased CF JVM max heap size and now CF service will not start

  - by Erik Vold

  So I went in to ColdFusion Administrator and increased my CF JVM max heap size, then I was told I would need to restart the service, so I stopped the service, and then tried to start it again and got the following error message: Windows could not start the ColdFusion 8 Application Server on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service vendor, and refer to service-specific error code 2. So I went to the Event Viewer application, then took a look at the Application log and saw an error that said: The ColdFusion 8 Application Server service could not be started. Check the server "coldfusion" log files for more information. So I went to my ColdFusion logs directory opened the server.log log file and I don't see anything useful in there or any of the other log files.. Any idea how I can change the JVM heap size back to what it was so that I can start CF again?

  Read the article

• How to debug why w3wp.exe crashes randomly?

  - by sassyboy

  On the main production server, the IIS worker process crashes sometimes. From the event viewer I get the following information. Faulting application name: w3wp.exe, version: 7.5.7601.17514, time stamp: 0x4ce7a5f8 Faulting module name: KERNELBASE.dll, version: 6.1.7601.17651, time stamp: 0x4e211319 Exception code: 0xe053534f Fault offset: 0x0000b9bc Faulting process id: 0x%9 Faulting application start time: 0x%10 Faulting application path: %11 Faulting module path: %12 Report Id: %13 This happens randomly on the prod server and I have not been able to recreate this crash anywhere else. This was happening on IIS 6, and we recently moved to Windows Server 2008 and IIS 7.5 and the crash happens there as well. How to go about finding the root cause of this?

  Read the article

• How can I trap errors for an application that is tightly coupled with IIS?

  - by PeanutsMonkey

  We have an unsupported application that relies on IIS however intermittently brings out the website it is integrated with. I have looked at the logs and there is nothing in the logs to indicate what the issue could be as the logs only have GET verbs. I have also looked at the event viewer and there are no error logged in there either. The application runs off a Windows 2008 server. Is there a freely available application we can have running in the background that will listen to or is aware of the application running and traps the error when it crashes? The unsupported application is a bespoke implementation for which we don't have code for and the developer is no longer contactable.

  Read the article

• Ubuntu to Ubuntu VNC over SSH tunnel

  - by rxt

  I have a Linux Ubuntu desktop at home, ssh enabled, vnc server installed, router rule configured. It all works, and at home I can connect via the local network from my Mac. From the outside I can login via ssh. I've configured putty as follows: session: host name and port number connection ssh tunnel: forwarded ports: L5900|192.168.0.23 the local address is: 192.168.1.45 When I make the connection I can login to the remote machine. Then I open Remote Desktop Viewer. I click connect protocol: vnc host: ? use host as ssh tunnel: ? I don't know what to use for the last two options. Which ip-addresses should I use?

  Read the article

• copying an lvm partition to a smaller disk, and renaming volume groups.

  - by dlamblin

  I was trying to shrink a vmdk (VMWare disk image) file to be as small as possible, and found two recommendations. The first is to cat /dev/zero into the fs then delete it, and run VMWare tools' shrink. This works okay. The second is to copy everything into a new vmdk. I went the second route. I did not use dd because I actaully want to use as few blocks as possible, instead of having a block-by-clok copy. Any unlinked files will still have blocks that aren't zeroed out. Secondly the centos image was mostly lvm, except for the boot partition, and my target was going to be 4gb instead of 8gb. I did use dd for the first 40mb to get the boot blocks and partition copied. I then used parted to create an identical primary boot, and smaller primary lvm. Then I used pvcreate on that device sdb2, vgcreate, and lvcreate to create a root and swap. I used mkfs.ext3fs on the root partition and then rsync -av / /2root excluding /proc /sys /2root /dev. So far everything went fine. My problem is that: The result is 2.7 GB while the source was 2.1 GB. This is weird to me. The second vgroup is called VolGroup01, while the original was called VolGroup00. How can I rename the VolGroup01 to VolGroup00 and swap it out after all this?

  Read the article

• LSI MegaRAID LINUX got Optimal after degradation but strange POST message

  - by kesrut

  Linux server box with LSI MegaRAID controller got degraded. But after some time RAID status changed to Optimal. Adapter 0 -- Virtual Drive Information: Virtual Drive: 0 (Target Id: 0) Name : RAID Level : Primary-1, Secondary-0, RAID Level Qualifier-0 Size : 2.727 TB Mirror Data : 2.727 TB State : Optimal Strip Size : 256 KB Number Of Drives per span:2 Span Depth : 3 Default Cache Policy: WriteBack, ReadAdaptive, Cached, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Cached, No Write Cache if Bad BBU Default Access Policy: Read/Write Current Access Policy: Read/Write Disk Cache Policy : Disk's Default Encryption Type : None Is VD Cached: No But now I'm getting RAID BIOS POST message: Your battery is either charging, bad or missing, and you have VDs configured for write-back mode. Because the battery is not currently usable, these VDs willl actually run in write-through mode until the battery is fully charged or replaced if it is bad or missing. (Image: http://cl.ly/image/1h1O093b1i2d) So may it be battery issue caused problem ? I get information about battery: BatteryType: iBBU Voltage: 4001 mV Current: 0 mA Temperature: 22 C Battery State : Operational BBU Firmware Status: Charging Status : None Voltage : OK Temperature : OK Learn Cycle Requested : No Learn Cycle Active : No Learn Cycle Status : OK Learn Cycle Timeout : No I2c Errors Detected : No Battery Pack Missing : No Battery Replacement required : No Remaining Capacity Low : No Periodic Learn Required : No Transparent Learn : No No space to cache offload : No Pack is about to fail & should be replaced : No Cache Offload premium feature required : No Module microcode update required : No Where can be problem ? I'm disabled alarms, but get them if enabled. But don't know how find root of problem.

  Read the article

• Windows 2008 DHCP service fails - "...failed to see a directory server for authorization."

  - by ewwhite

  I have a small environment running Windows 2008 R2 where the DHCP service on the domain controller fails every two weeks. The most-visible error is Event ID 1059 and the Event Viewer message is: "The DHCP service failed to see a directory server for authorization." The setup features two domain controller and the usual services and roles (file, print, Exchange). Restarting the service fails for a variety of reasons. I've had the following messages at different times: "Not enough storage is available to complete this operation". "Unable to determine the DHCP Server version for the Server 192.168.x.x" "The DHCP service has detected that it is running on a DC and has no credentials configured for use with Dynamic DNS registrations initiated by the DHCP service." A reboot of the domain controller resolves the issue for ~2 weeks. The systems are virtualized and there are no network connectivity issues. Any ideas what's happening here?

  Read the article

• Cannot open any applications on windows server 2008 R2 Standard edition

  - by kishore

  I have a server running on Windows server 2008 R2. It is recently added as a member of a domain. I am not able to start any applications in thew server. When I tried to open Event viewer it errored out saying "The page file is to small to complete the action". I am experiencing same problem when I tried to open Sql server Management studio, task scheduler or any other application. The windows server serves as a production database server, but our applications are not experiencing any problems. Can someone please help?

  Read the article

• 421 Concurrent Connections - Ratelimit from helpdesk to rackspace server

  - by g18c

  We have Kayako helpdesk running on our WHM Linux server. When e-mails come in from customers, notifications are sent out by Kayako to a number of staff whose mailboxes are hosted on Rackspace mail servers. I noticed a large queue in the Exim queued message viewer of WHM - when looking in Exim logs I can see many lines 2012-10-13 20:06:56 1TN72s-0007Cw-1l SMTP error from remote mail server after initial connection: host mx2.emailsrvr.com [173.203.2.32]: 421 Too many concurrent connections from this client. One client email results in about 5 emails to rackspace servers, perhaps 60 emails per 1 hour on average - not a huge amount but enough to cause messages to be rejected when sent in short bursts. In this case ideally if we can limit the connections sent to the rackspace server we can comply with their limit. For our requirements if we send 1 email every10 seconds or so, this would be OK. Messages to all other servers should go through a normal rates, only mx1.emailsrvr.com and mx2.emailsrvr.com should have this connection limit policy applied. Is this possible?

  Read the article

• Outlook Shared Address book and contact not displaying

  - by user224061

  We have a shared Exchange addressbook with distribution email groups. When someone connects to the shared addressbook, composes an email to a group, the email distribution list is empty, then the distribution list is expanded. In troubleshooting, I noticed that when we expand the distribution list to view the recipients, most of the recipients are missing and only semicolons appear. CLICK HERE FOR IMAGE Further troubleshooting, I notice that when I open the distribution list with my Outlook client and click on the Update Now icon, and then go to create the email then when I expand the group the email addresses now appear. CLICK HERE FOR IMAGE Now, my Outlook profile is a cached profile. The shared contact list that I pulled the distribution list from is an online/non-cached shared contact list. What I also found is that if I switched my Outlook client to be online only(not cached) the share address book lists appear properly when expanded. Is there any way to make this list appear correctly without having to click on update now for each and every distribution list in the shared contacts list we have on the server? I would really prefer that every time one wants to use this shared contact list, they do not have o click the update not button or switch from cached mode to make this work. T.I.A

  Read the article

• Remove Shell Extension Folder X64

  - by Florian Peschka

  I have a very strange shell extension folder which I just can't get rid of. How can I get rid of this? I already downloaded ShellExViewer, but I cannot find any extension called "X64", nor are the other extensions which reside in that folder anywhere in the Viewer. I am also not able to find that folder in the registry, but that's probably because I don't know where to look. How can I edit this so the contents of the folder are put in the "default" menu and not in a subfolder?

  Read the article

• IIS Logs not getting created

  - by Chris

  Hi I have a site running on IIS 6. I have turned on logging on the website tab of IIS and specified a directory for it to write to. Set it to an hourly schedule. However no logs are ever created. Have reset iis. checked disk space and permissions on the directory it is writing to but no logs are ever created. I can see this did work once, as there are logs created in the system32/logfiles directory from about a year ago. Even if I specify that directory nothing new gets created This is on a hosted service What else can I check? Is there any place that errors would be written to that might give me a clue as to what is going on? Have tried event viewer but nothing untoward in there Would appreciate any pointers on this

  Read the article

• Where do I define a group policy that will set a users desktop background color to green the first time they log in?

  - by Tyler

  Servers: W2k8 R2 x64 Desktops: Win7 Pro x64 Our current group policy uses a custom ADM file to define certain properties of the desktop (Background Image (centered), Background Color is green (00 74 00)). This policy works for us, but the down-side is that policies defined in our custom ADM are only applied after a GPUpdate /Force is applied. We would like these desktop theme settings to be applied the first time the user logs onto the computer. I've been working on a new policy that forces the computer to wait for the network when the user logs on to handle folder redirection. The reason for writing the new policy was to resolve the issue that a user needs to run GPupdate /Force the first time they log in, so it doesn't make sense for me to implement the new policy if there is still something that requires GPUpdate /Force to get the user in the state that we want them. I've moved the setting for background image out into Admin Templates- Desktop- Desktop- "Desktop Wallpaper" so this is now being set properly when the user first logs in. Now I'm left with a black background until I force a group policy update. I have tried to play around with setting a default "Theme" and had limited success; this was not reliable enough to call a solution. I suppose I could set the background color with a script? Any thoughts? It feels like I'm missing something obvious, or that this should be much easier than it is.

  Read the article

• Android failure to boot on LG [migrated]

  - by Ukavi

  I need to recover data from my AT&T LG Thrill Android Phone Background: My AT&T LG Thrill phone's battery died a couple of days ago because I forgot to charge it. When I charged the phone and tried to turn it on, it showed the LG logo followed by the dropping balls and the AT&T "Rethink Possible" screen. I then get a mesage that the Application Google Services Framework has crashed and the phone goes into a loop with the dropping balls showing again followed by "Rethink Possible" screen. This sequence repeats itself over and over and the phone does not get out of this loop. I have been able to go into the recovery screen (both Safe Mode and the Android Recovery Service) and have cleared cache, etc. However, I DO NOT want to wipe user data and restore to factory settings as this will wipe all of my data (pictures, application data, etc). Solution Needed: I need a suggestion to a way of accessing my data so that I can back it up onto an SD card/computer. I DO NOT want to root the phone as this may void the warranty. What I'm looking for is a way of perhaps putting the original flash image on the micro SD card and then have the phone read that image. Or some other similar solution that will get the phone out of this loop and allow me to get to the data.

  Read the article

• Printing from a Linux using an Acer Aspire Netbook

  - by JoelFan

  A friend asked me to check why their Linux Acer Aspire netbook can't print to their HP printer. When I plugged in the USB cable, the a "balloon" popped up on the netbook saying it was installing the printer. But the printing does not work. I was able to get into a Settings area and click on Print Test Page but nothing happened. If it was Ubuntu, I would go into the Log File Viewer, but I couldn't find that on whatever Linux flavor the Acer is running. I couldn't even figure out how to get to a terminal (shell) window. I tried searching the HP and Acer sites but nothing seems to apply to this issue.

  Read the article

• MDT 2010 Litetouch.vbs Fails to Launch

  - by Mitch

  I have the custom image captured. Import the image and files. Prepare the customsettings.ini and the boot.ini to minimize the questions the deployment team will need to answer. Everything works like a charm on virtual machines but when I map to the scripts folder on the deployment share and double-click litetouch.vbs it creates the c:\minint folder, subfolders, and a couple of log files then nothing. Here's what the log files look like: <![LOG[Property LogPath is now = C:\MININT\SMSOSD\OSDLOGS]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[Property CleanStart is now = ]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[Microsoft Deployment Toolkit version: 5.1.1642.01]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[Property Debug is now = FALSE]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[GetAllFixedDrives(False)]LOG]!><time="15:54:28.000+000" date="03-08-2011" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> Anyone encounter this before or know what might be happening/not happening and can direct me in the right way? I've only found a couple of other references to this anywhere and they had no solution/cause listed either. I'm stumped.

  Read the article

• Difference between genuine Windows and Pirated Windows [closed]

  - by Murtaza

  I always had This question in mind, that basically what difference does it make by installing a pirated windows, beside the fact that its un-ethical I myself use Genuine windows, but just for a test I installed pirated Windows7 Ultimate 64-bit on another laptop and one laptop has been installed with same Genuine windows. But I can't observe any difference between these two, both windows gets updated by microsoft and all are same, can someone point out the difference? And if any viewer doesnot know the answer, and wants to know it, you can vote-up so it can be viewed by more users and get answered. Thankyou.

  Read the article

• SQL 2008 Reporting Services Report Manager blank on Win 7

  - by Daniel Root

  I have installed SQL Server 2008 Reporting Services on my development laptop running windows 7. When I browse to the report manager, only the header is shown. The content pane is blank, and there is no 'Site Settings' option, New Folder options, etc. I found plenty of similar stories about SQL 2005, and then the fix was to manage permissions in the virtual directory in IIS. However, in 2008, there is no virtual directory - RS manages this outside of IIS. Per other serverfault articles, I've tried the following: adding my account to the reporting services group changing the service to run as local system made sure localhost was trusted site in IE ran IE as admin installed SQL Server 2008 SP1 There are no errors in the event viewer. Perhaps related, if I browse to the webservice, I also get the error: The permissions granted to user 'Computer\User' are insufficient for performing this operation. (rsAccessDenied)

  Read the article

< Previous Page | 443 444 445 446 447 448 449 450 451 452 453 454  | Next Page >